# Boeing Service Bulletin DC8-57-104: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2015-2455; AD 2016-04-21 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin DC8-57-104](https://openairdocs.org/service-documents/boeing/dc8-57-104.md)
- Title as filed: U.S. DOT/FAA - SB-DC8-57-104-00
- Pages: 54
- PDF: https://openairdocs.org/files/sha256/16/92/16926822354f3aebe168a57df1f55dcb8effeee548ce76c34e6796c751ff65b7
- Page: https://openairdocs.org/service-documents/boeing/dc8-57-104/file/16926822354f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
DC8
Service Bulletin
Number: DC8-57-104
Original Issue: August 18, 2014
ATA System: 5710
SUBJECT: WINGS - Wing Plating Skin and Stringers - Lower Wing Skins, Stringers, and Splice
Fittings at Stations Xw=+408 and Xw=-408 From Stringer 51 to Stringer 65 Inspection
and Repair or Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2014 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: August 18, 2014
DC8-57-104
1 of 54
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
2 of 54
BOEING SERVICE BULLETIN DC8-57-104
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 4
D. Description .............................................. 1 4
E. Compliance .............................................. 1 6
F. Approval ............................................... 1 7
G. Manpower .............................................. 1 7
H. Weight and Balance Changes .................................... 1 8
I. Electrical Load Data ......................................... 1 9
J. References .............................................. 1 9
1. Existing Data: ......................................... 1 9
2. Data Supplied with this Service Bulletin: ........................... 1 9
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 0
K. Publications Affected ........................................ 2 0
L. Interchangeability and Intermixability of Parts ........................... 2 0
M. Software Accomplishment Summary ................................ 2 0
2. MATERIAL INFORMATION ........................................ 2 1
A. Material - Price and Availability ................................... 2 1
B. Industry Support Information .................................... 2 1
C. Parts Necessary for Each Airplane ................................. 2 1
1. Kits/Parts: ........................................... 2 1
2. Parts and Materials Supplied by the Operator: ........................ 2 1
3. Parts Modified and Reidentified: ............................... 2 4
4. Parts Removed and Not Replaced: .............................. 2 4
D. Parts Necessary to Change Spares ................................. 2 4
E. Special Tooling - Price and Availability ............................... 2 4
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 5
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 7
A. GENERAL INFORMATION ..................................... 2 7
B. WORK INSTRUCTIONS ....................................... 2 9
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO LEFT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00
FROM STRINGER 51 TO STRINGER 65 [Group 1-3, Configuration 2] ........... 3 1
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= -408.00
FROM STRINGER 51 TO STRINGER 65 [Group 1-3, Configuration 2] ........... 3 6
FIGURE 3: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00 [Group
1-3, Configuration 2] ...................................... 4 1
FIGURE 4: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00 [Group
1-3, Configuration 2] ...................................... 4 4
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
3 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 4

FIGURE 5: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00 [Group
1-3, Configuration 2] ...................................... 4 7
FIGURE 6: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00 [Group
1-3, Configuration 2] ...................................... 5 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
4 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 5

Commercial 
Airplanes
DC8
Service Bulletin
SummaryNumber: DC8-57-104Original Issue: August 18, 2014
ATA System: 5710
SUBJECT: WINGS - Wing Plating Skin and Stringers - Lower Wing Skins, Stringers, and Splice
Fittings at Stations Xw=+408 and Xw=-408 From Stringer 51 to Stringer 65 Inspection
and Repair or Modification
CONCURRENT REQUIREMENTS
None.
BACKGROUND
14 Code of Federal Regulations (CFR) Part 26.21, Amendment 26-5 with effective date January 14, 2011,
requires the release of new service actions (Service Bulletins) to support airplane operation up to the Widespread
Fatigue Damage (WFD) regulation Limit of Validity (LOV). New service actions has been identified to support
operation up to the DC-8 LOV. Inspection and modification of the lower wing skin, stringers and splice fittings
in the left and right wings will support operation up to the DC-8 LOV. If the inspection and repair or modification
are not completed, there may be undetected cracks in the lower skins, stringers, and/or splice fittings fastener
holes which could result in the loss of fail safe structural integrity.
The left and right lower surface wing splices at XW = + 408 and XW = -408 have been determined to be structures
that are susceptible to Widespread Fatigue Damage (WFD).
Boeing Fleet Team Digest (FTD) DC-8 FTD FTD-51-12001 is related to this service bulletin.
ACTION
This service bulletin provides instructions to do as follows:
Group 1-3, Configuration 1:
1. Contact The Boeing Company to get instructions for the repair and do the work instructed by The
Boeing Company.
Group 1-3, Configuration 2:
1. Do Eddy Current High Frequency (ETHF) inspection for cracks of the fastener open holes common to
the lower skins, stringers, and splice fittings at stations Xw=408 and Xw=-408 from stringer 51 to stringer
65. Based on inspection findings do what follows:
CONDITION 1: ANY CRACK FOUND IN ANY HOLE
a. Contact The Boeing Company to get instructions for the repair and do the work instructed by The
Boeing Company.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
5 of 54

### Page 6

CONDITION 2: NO CRACK FOUND IN ANY HOLE
a. Install external doublers and fasteners.
b. Do external doubler Eddy Current Low Frequency (ETLF) Inspection around fasteners. Based on
inspection findings do what follows:
CONDITION 3: NO CRACK FOUND AROUND ANY EXTERNAL DOUBLER FASTENER
a. Do repeat external Eddy Current Low Frequency (ETLF) Inspection around fastener at intervals
specified in Paragraph 1.E., Compliance.
CONDITION 4: ANY CRACK FOUND AROUND ANY EXTERNAL DOUBLER FASTENER
a. Contact The Boeing Company to get instructions for the repair and do the work instructed by The
Boeing Company.
EFFECTIVITY
DC8 Airplane(s) DC-8-55, DC-8-61F, DC-8-62, DC-8-62F, DC-8-63, DC-8-63F, DC-8-71F, DC-8-72F,
DC-8-73F,DC-8F-54, and DC-8F-55. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplane(s).
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and/or repair procedures given in this service
bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
6 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 7 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
LOWER WING SKINS, STRINGERS
AND SPLICE FITTINGS AT
STATIONS XW=408.000 AND
Xw=-408.000 FROM STRINGER 51
TO STRINGER 65 INSPECTION
AND REPAIR OR MODIFICATION  2310960
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  7 of 54

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
8 of 54
BOEING SERVICE BULLETIN DC8-57-104
BLANK PAGE

### Page 9

Commercial 
Airplanes
DC8
Service Bulletin
Number: DC8-57-104
Original Issue: August 18, 2014
ATA System: 5710
SUBJECT: WINGS - Wing Plating Skin and Stringers - Lower Wing Skins, Stringers, and Splice
Fittings at Stations Xw=+408 and Xw=-408 From Stringer 51 to Stringer 65 Inspection
and Repair or Modification
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
DC-8-55, DC-8F-54, DC-8F-55, DC-8-71F-1
DC-8 Airplanes with previous structural repairs at the lower skins,
stringers, and/or splice.
1
DC8- Airplanes with NO previous repairs at the lower skins, stringers,
and/or splice fitting.
2
DC-8-61F-2
DC-8 Airplanes with previous structural repairs at the lower skins,
stringers, and/or splice.
1
DC-8 Airplanes with NO previous repairs at the lower skins, stringers,
and/or splice.
2
DC-8-62, DC-8-62F, DC-8-63, DC-8-63F, DC-8-72F, DC-8-73F-3
DC-8 Airplanes with previous structural repairs at the lower skins,
stringers, and/or splice.
1
DC-8 Airplanes with NO previous repairs at the lower skins, stringers,
and/or splice.
2
Airplane Models:
DC-8-55, DC-8-61F, DC-8-62, DC-8-62F, DC-8-63, DC-8-63F, DC-8-71F, DC-8-72F, DC-8-73F,
DC-8F-54, DC-8F-55
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
9 of 54

### Page 10

GroupFuselage Num-
ber
1122
1157
1175
1178 - 179
1180
1182
1185
1187
1189
1195
1197
1199
1200 - 201
1203
1207 - 209
1210
1215
1218
1220
1223
1225
1229
1232
1234 - 236
1238
1240 - 242
1244
1246 - 248
1250 - 256
1259
1261 - 262
1265
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
10 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 11

GroupFuselage Num-
ber
1267 - 269
3270
1271 - 272
1274 - 278
3279
1282 - 284
3286
2287
1288 - 289
1292
3293
1294 - 295
3298 - 299
3300
1302
3303 - 304
2305 - 306
3307
1308
3309
3311 - 312
1313
1316 - 317
3318 - 319
1320 - 321
3322 - 323
1326
3327
1328 - 329
1331
3332 - 335
1337 - 339
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
11 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 12

GroupFuselage Num-
ber
1340 - 343
3344
1346
3347 - 348
1350 - 351
2352
3353
1354
1356
1358
2360
3361 - 362
1363
2364
3365 - 367
1368 - 369
3370 - 371
1372 - 373
3375 - 379
3380
1381 - 382
3383
3385 - 386
1387 - 388
3389
3391 - 396
1397 - 399
1400
3401
3403
1404
1406
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
12 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 13

GroupFuselage Num-
ber
3407
1408
1410
3411 - 417
1420
3421 - 424
1425 - 426
3427 - 428
3430 - 434
3437 - 439
3440 - 447
1448 - 449
1450
3451 - 454
3456
1459
1460
3461
1462
3463 - 469
3470
3472
3474 - 476
1477
3478 - 479
3480 - 489
3490 - 491
1492
3493 - 494
1495
3496
3498 - 499
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
13 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 14

GroupFuselage Num-
ber
3500 - 506
3508 - 509
3511 - 513
3515 - 519
3520 - 529
3530 - 539
3540
3542
3546 - 549
3550 - 556
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
14 Code of Federal Regulations (CFR) Part 26.21, Amendment 26-5 with effective date January 14,
2011, requires the release of new service actions (Service Bulletins) to support airplane operation up
to the Widespread Fatigue Damage (WFD) regulation Limit of Validity (LOV). New service actions has
been identified to support operation up to the DC-8 LOV. Inspection and modification of the lower wing
skin, stringers and splice fittings in the left and right wings will support operation up to the DC-8 LOV.
If the inspection and repair or modification are not completed, there may be undetected cracks in the
lower skins, stringers, and/or splice fittings fastener holes which could result in the loss of fail safe
structural integrity.
The left and right lower surface wing splices at XW = + 408 and XW = -408 have been determined to
be structures that are susceptible to Widespread Fatigue Damage (WFD).
Boeing Fleet Team Digest (FTD) DC-8 FTD FTD-51-12001 is related to this service bulletin.
D. Description
This service bulletin provides instructions to do as follows:
Group 1-3, Configuration 1:
1. Contact The Boeing Company to get instructions for the repair and do the work instructed by The
Boeing Company.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
14 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 15

Group 1-3, Configuration 2:
1. Do Eddy Current High Frequency (ETHF) inspection for cracks of the fastener open holes common
to the lower skins, stringers, and splice fittings at stations Xw=408 and Xw=-408 from stringer 51
to stringer 65. Based on inspection findings do what follows:
CONDITION 1: ANY CRACK FOUND IN ANY HOLE
a. Contact The Boeing Company to get instructions for the repair and do the work instructed by
The Boeing Company.
CONDITION 2: NO CRACK FOUND IN ANY HOLE
a. Install external doublers and fasteners.
b. Do external doubler Eddy Current Low Frequency (ETLF) Inspection around fasteners. Based
on inspection findings do what follows:
CONDITION 3: NO CRACK FOUND AROUND ANY EXTERNAL DOUBLER FASTENER
a. Do repeat external Eddy Current Low Frequency (ETLF) Inspection around fastener at intervals
specified in Paragraph 1.E., Compliance.
CONDITION 4: ANY CRACK FOUND AROUND ANY EXTERNAL DOUBLER FASTENER
a. Contact The Boeing Company to get instructions for the repair and do the work instructed by
The Boeing Company.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
117DC-8-55, DC-8-71F, DC-8F-54,
DC-8F-55
Group 2:
Affected Maintenance Zones
ZoneModel
117DC-8-61F
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
15 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 16

Group 3:
Affected Maintenance Zones
ZoneModel
117DC-8-62, DC-8-62F, DC-8-63,
DC-8-63F, DC-8-72F, DC-8-73F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Group 1-3, Configuration 1:
Within 120 days after the original issue date of this service bulletin, contact Boeing to get instructions
for the inspection, repair and/or modification and do the work instructed by Boeing.
Group 1-3, Configuration 2:
Table 1: ETHF Inspection for Cracks of Open Fastener Holes Common to Lower Wing Skins, Stringers,
and Splice Fittings at Stations Xw=+408 and Xw=-408 From Stringer 51 to Stringer 65:
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 6 years
after the original
issue date of
this service bul-
letin (NOT to ex-
ceed 56,000 to-
tal flight cycles)
Before 32,000
total flight cy-
cles.
Do Eddy Current High
Frequency (ETHF) inspec-
tion for cracks of the open
fastener holes common
to the lower skins,
stringers, and splice fit-
ting at stations Xw=408
and Xw=-408 from
stringer 51 to stringer 65.
All Airplanes
--Before further
flight.
Contact The Boeing
Company to get instruc-
tions for the repair and do
the work instructed by
The Boeing Company.
CONDITION 1: ANY
CRACK FOUND IN ANY
HOLE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
16 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 17

Group 1-3, Configuration 2:
Table 1: ETHF Inspection for Cracks of Open Fastener Holes Common to Lower Wing Skins, Stringers,
and Splice Fittings at Stations Xw=+408 and Xw=-408 From Stringer 51 to Stringer 65:
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Install external doublers.CONDITION 2: NO
CRACK FOUND IN ANY
HOLE ---AND
--Within 10,000
flight cycles af-
ter external dou-
bler installation.
Do external doubler Eddy
Current Low Frequency
(ETLF) Inspection around
fasteners.
600 flight cycles.--Do repeat external dou-
bler Eddy Current Low
Frequency (ETLF) Inspec-
tion around fasteners.
CONDITION 3: NO
CRACK FOUND AROUND
ANY EXTERNAL DOU-
BLER FASTENER
--Before further
flight.
Contact The Boeing
Company to get instruc-
tions for the repair and do
the work instructed by
The Boeing Company.
CONDITION 4: ANY
CRACK FOUND AROUND
ANY EXTERNAL DOU-
BLER FASTENER
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved. This service
bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as
modified by other approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
In addition, the Manager of the FAA Los Angeles Aircraft Certification Office approves the action (i.e.
inspection or modification) defined in this service bulletin as an alternative method of compliance to
the requirements of paragraph (f) of AD 2008-26-07 and a method of compliance to paragraphs (i), (j),
and (m) of AD 2008-25-05 for only the lower wing splice at stations XW=+408 and XW=-408 in between
Stringer 51 and Stringer 65. All provisions of AD 2008-26-07 and AD 2008-25-05 that are not specifically
referenced in the above statement remain fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each wing.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
17 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 18

— Time to schedule the work
— Time to inspect the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1-3, Configuration 1:
None.
Group 1-3, Configuration 2:
Elapsed HoursTask HoursNumber of PersonsTask
1.01.01Open Access
3.03.01Figure 1
3.03.01Figure 2
1.01.01Close Access
8.08.0TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Group 1-3, Configuration 1:
None.
Group 1, Configuration 2:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)Airplane
+24640.0+25.0+985.6DC-8F-54, DC-8-
55, DC-8F-55, DC-
8-71F
Group 2, Configuration 2:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)Airplane
+24832.1+25.2+985.4DC-8-61F
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
18 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 19

Group 3, Configuration 2:
Moment Change
(MEW) IN.-LBS
Mfr's Empty
Weight (MEW)
LBS
Approximate Sta-
tion (Inches)Airplane
+24832.1+25.2+985.4DC-8-62, DC-8-63,
DC-8-72CF, DC-8-
73CF
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Bulletin (SB) DC8-57A102
b. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2008-25-05, 2008-26-07
c. Non-Destructive Test Standard Practices Manual (NDTSPM) 06-10-01.003 Procedure 3,
06-10-02.001, Procedure 1
d. Standard Overhaul Practices Manual (SOPM) 20-50-01
e. DC-8 Aircraft Maintenance Manual (AMM) 06-11-02, 13-1-2, 28-00, 28-00-00, 28-10-1, 28-1-1
f. DC-8 Fleet Team Digest (FTD) FTD-51-12001
g. DC-8 Structural Repair Manual (SRM) Chapter 51
2. Data Supplied with this Service Bulletin:
No data is supplied with this service bulletin. To obtain the data necessary to support this service
bulletin submit a data request to:
Data and Services Management
MS D800-0019
3855 Lakewood Boulevard
Long Beach, California 90846
Phone: (562) 593-6996
Fax: (562) 593-2001
E-mail: dse.boecom@boeing.com
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No
-ADWGDC-8 WING MOD, LOWER Xw=408.343SR08570025
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
19 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 20

3. Installation Drawings Used in the Preparation of this Service Bulletin:
ChangeTitleDocument Number
ADC-8 WING MOD, LOWER
Xw=408.343
SR08570025
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this service bulletin.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
20 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 21

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection/repair procedures given in this service
bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
Group 1, Configuration 2:
NotesNameQTYPart Number /
Specification
(a)PIN83D0009-8X7
(b)PIN, OVERSIZE442HLT629-8-8
(b)PIN, OVERSIZE192HLT629-8-9
(b)PIN, OVERSIZE326HLT629-8-10
(b)PIN, OVERSIZE18HLT629-8-11
(b)PIN, OVERSIZE2HLT629-8-12
NUT988MS21042L4
RIVET168NAS1097AD6-9
RIVET192NAS1097AD6-10
RIVET32NAS1097AD6-11
WASHER988NAS1252-416H
DOUBLER1SR08570025-3
DOUBLER1SR08570025-4
DOUBLER1SR08570025-5
DOUBLER1SR08570025-6
DOUBLER1SR08570025-7
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
21 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 22

Group 1, Configuration 2:
NotesNameQTYPart Number /
Specification
DOUBLER1SR08570025-8
DOUBLER1SR08570025-9
DOUBLER1SR08570025-10
(d)Sealant4
Quarts
PR-1422 B2
Or equivalent.
(a) Or approved equivalent, refer to AEPL, Drawing
7595071.
(b) Can be purchased from: Hi-Shear Corporation, 2600
Skypark Drive, Torrance, California 90505. CAGE:
73197.
(c) If grip length shown is not available at Boeing, fas-
teners supplied in kits may be one grip length longer
than indicated. Also, if any fasteners part numbers
listed are not available or have been superseded,
substitute fasteners may be supplied in kits.
(d) Refer to the Qualified Products List at the end of the
Boeing Material Specification (BMS) for supplier
data.
Group 2, Configuration 2:
NotesNameQTYPart Number /
Specification
(a)PIN83D0009-8X7
(b)PIN, OVERSIZE444HLT629-8-8
(b)PIN, OVERSIZE176HLT629-8-9
(b)PIN, OVERSIZE336HLT629-8-10
(b)PIN, OVERSIZE22HLT629-8-11
(b)PIN, OVERSIZE2HLT629-8-12
NUT988MS21042L4
RIVET160NAS1097AD6-9
RIVET232NAS1097AD6-10
WASHER988NAS1252-416H
DOUBLER1SR08570025-3
DOUBLER1SR08570025-4
DOUBLER1SR08570025-7
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
22 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 23

Group 2, Configuration 2:
NotesNameQTYPart Number /
Specification
DOUBLER1SR08570025-8
DOUBLER1SR08570025-11
DOUBLER1SR08570025-12
DOUBLER1SR08570025-13
DOUBLER1SR08570025-14
(d)Sealant4
Quarts
PR-1422 B2
Or equivalent.
(a) Or approved equivalent, refer to AEPL, Drawing
7595071.
(b) Can be purchased from: Hi-Shear Corporation, 2600
Skypark Drive, Torrance, California 90505. CAGE:
73197.
(c) If grip length shown is not available at Boeing, fas-
teners supplied in kits may be one grip length longer
than indicated. Also, if any fasteners part numbers
listed are not available or have been superseded,
substitute fasteners may be supplied in kits.
(d) Refer to the Qualified Products List at the end of the
Boeing Material Specification (BMS) for supplier
data.
Group 3, Configuration 2:
NotesNameQTYPart Number /
Specification
(a)PIN83D0009-8X7
(b)PIN, OVERSIZE444HLT629-8-8
(b)PIN, OVERSIZE172HLT629-8-9
(b)PIN, OVERSIZE340HLT629-8-10
(b)PIN, OVERSIZE22HLT629-8-11
(b)PIN, OVERSIZE2HLT629-8-12
NUT988MS21042L4
RIVET160NAS1097AD6-9
RIVET232NAS1097AD6-10
WASHER988NAS1252-416H
DOUBLER1SR08570025-3
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
23 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 24

Group 3, Configuration 2:
NotesNameQTYPart Number /
Specification
DOUBLER1SR08570025-4
DOUBLER1SR08570025-7
DOUBLER1SR08570025-8
DOUBLER1SR08570025-11
DOUBLER1SR08570025-12
DOUBLER1SR08570025-13
DOUBLER1SR08570025-14
(d)Sealant4
Quarts
PR-1422 B2
Or equivalent.
(a) Or approved equivalent, refer to AEPL, Drawing
7595071.
(b) Can be purchased from: Hi-Shear Corporation, 2600
Skypark Drive, Torrance, California 90505. CAGE:
73197.
(c) If grip length shown is not available at Boeing, fas-
teners supplied in kits may be one grip length longer
than indicated. Also, if any fasteners part numbers
listed are not available or have been superseded,
substitute fasteners may be supplied in kits.
(d) Refer to the Qualified Products List at the end of the
Boeing Material Specification (BMS) for supplier
data.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
24 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 25

F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
25 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 26

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
26 of 54
BOEING SERVICE BULLETIN DC8-57-104
BLANK PAGE

### Page 27

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY
ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE
PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE
CAN OCCUR.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE
TO THE AIRPLANE OR EQUIPMENT.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms
2. Equivalent parts are listed in the AEPL, Drawing 7595071.
3. Use the approved fastener and process material substitutions, in accordance with
DC-8 SRM Chapter 51.
4. If the length of any fastener specified in this service bulletin does not meet installation
standards given in Structural Repair Manual (SRM) Chapter 51, then a fastener of
the same specification, or an approved substitute, with a length which meets the
installation standards given in SRM Chapter 51 may be used. In addition, washers
may be installed for fastener grip length in accordance with SRM Chapter 51. Refer
to SOPM 20-50-01 for alternate full threaded fasteners (screws) needed for installation
in this service bulletin.
5. A 1/8-inch thick stack of the same type washers called for in this service bulletin is
the maximum thickness which may be used under fastener head or nut to counteract
accumulation of tolerances.
EXCEPTION: When the available fastener length increments are greater than
1/16-inch, a 3/16-inch thick stack of the same type washers may be used.
6. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch.
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets are in DC-8 SRM Chapter 51
– Torque Values:
— Values for structural fasteners are given in DC-8 Structural Repair Manual,
Chapter 51.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
27 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 28

— Values for airframe maintenance tasks are included in Chapter 20 of DC-8
Airplane Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of DC-8
Airplane Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
7. Obey all of the warnings and cautions given in the specified manual sections.
8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
9. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U' or 'Y' in place of the '-' (dash) in the part number. It is permitted
to install parts identified with a 'U' or 'Y' as an alternative to the '-' (dash) number
part. Boeing Drawing SE10000000, Sheets 5.0 and 6.0 contain more data.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
12. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
13. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
14. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
15. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
16. The CONDITIONS, ACTIONS and OPTIONS shown apply to each open fastener
hole independently.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
28 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 29

17. Some steps in the Work Instructions are identified as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
identified as RC must be done to comply with the AD. Alternative procedures for
steps not identified with RC can be used if the RC steps can still be done as specified,
and the airplane can be put back in a serviceable condition. An Alternative Method
of Compliance (AMOC) is not necessary for deviations to steps that are not identified
as RC.
B. WORK INSTRUCTIONS
Group 1-3, Configuration 1:
RC - Contact Boeing to get instructions for the repair for this service bulletin, and do the work instructed
by Boeing.
Group 1-3, Configuration 2:
1. Drain and purge Number 1 Main fuel tank, Number 1 Alternate, Number 4 Main, and Number 4
Alternate, fuel tanks. Refer to DC-8 AMM 28-00 as an accepted procedure.
WARNING: FUEL VAPOR IN TANKS MAY BE TOO RICH TO IGNITE WHEN TANKS ARE
INITIALLY OPENED; HOWEVER VAPOR CONCENTRATION WILL PASS
THROUGH AN EXPLOSIVE MIXTURE LEVEL DURING TANK VENTILATION.
VAPOR MIXTURES TOO LEAN TO IGNITE, IF ALLOWED TO ACCUMULATE IN
AN UNVENTILATED SPACE, CAN FORM AN EXPLOSIVE MIXTURE.
WARNING: TANKS MUST BE PURGED TO SAFE ATMOSPHERIC CONDITION, BELOW
LOWER EXPLOSIVE LIMITS, AS DETERMINED BY QUALIFIED PERSONNEL
USING FUEL VAPOR MEASURING EQUIPMENT. CONSULT LOCAL AUTHORITY
OR REGULATORY AGENCY.
a. Remove external access doors 505A, 505B, 514H, and 514I. Refer to DC-8 AMM 06-11-02
or DC-8 AMM 13-1-2 for Series 50 and prior as accepted procedures.
b. Remove internal access doors 560A and 560B to gain access forward of the center spar.
2. Remove fuel tank plumbing and equipment necessary to facilitate access.
3. RC - Do an Eddy Current High Frequency (ETHF) inspection for cracks in accordance with FIGURE
1 and FIGURE 2 and based on inspection findings do what follows:
a. CONDITION 1: ANY CRACK FOUND IN ANY HOLE
(1) RC - Contact The Boeing Company to get instructions for the repair and do the work
instructed by The Boeing Company.
b. CONDITION 2: NO CRACK FOUND IN ANY HOLE
(1) RC - Install external doublers in accordance with the drawing number that follows:
Group 1, Configuration 2:
SR08570025-7001
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
29 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 30

Group 2, Configuration 2:
SR08570025-7003
Group 3, Configuration 2:
SR08570025-7005
(2) RC - Do external doubler Eddy Current Low Frequency (ETLF) Inspection around fasteners
in accordance with FIGURE 3, FIGURE 4, FIGURE 5, and FIGURE 6 at intervals specified
in Paragraph 1.E., Compliance.
(a) CONDITION 3: NO CRACK FOUND AROUND ANY EXTERNAL DOUBLER
FASTENER
1) RC - Repeat external doubler Eddy Current Low Frequency (ETLF) Inspection
around fasteners in accordance with FIGURE 3, FIGURE 4, FIGURE 5, and
FIGURE 6 at intervals specified in Paragraph 1.E., Compliance.
(b) CONDITION 4: ANY CRACK FOUND AROUND ANY EXTERNAL DOUBLER
FASTENER
1) RC - Contact Boeing to get instructions for the repair for this service bulletin,
and do the work instructed by Boeing.
4. Reinstall fuel tank plumbing and equipment previously removed to facilitate access as given in
DC-8 AMM 28-00-00.
5. Refill fuel tank(s) opened for inspection or repair and check for fuel leaks. If necessary, repair fuel
leaks as given in DC-8 AMM 28-1-1 for Series 50 airplanes or DC-8 AMM 28-10-1 for Series 60
airplanes.
6. Put the airplane back to a serviceable condition
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
30 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 31 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
ALL STRINGER
LOCATIONS SHOWN C
(TYPICAL)
FRONT
SPAR
Xrs=393
- STGR 65
-STGR 64
→ STGR 63
\rs=428  - STGR 62
CENTER
SPAR
STGR 61
- STGR 60
LOOKING DOWN AT WING LOWER SKIN SURFACE  2310970
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO LEFT WING
SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00 FROM STRINGER
51 TO STRINGER 65
(SHEET 1 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  31 of 54

### Page 32 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
ALL STRINGER  LOCATIONS SHOWN C  -STGR 59
(TYPICAL)
Xw=408
IBD  •STGR 58
Xrs=428
-STGR 57
-STGR 56
•STGR 55
- STGR 54
+STGR 53
STGR 52
-STGR 51
REAR
SPAR
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO LEFT WING
SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00 FROM STRINGER
51 TO STRINGER 65
(SHEET 2 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  32 of 54

### Page 33 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
0216 LOCATIONS
STRINGER SPLICE  -=== - CENTER LINE STRINGER
FITTING  TYPICAL
• WING STRINGER
| ENSPE  INSPECTION
• C
STRINGER SPLICE
FITTING
SKIN  SKIN.
WING  STRINGER  C  WING  STRINGER  2311012
A-A  B-B
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMONTO LEFT WING
SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00 FROM STRINGER
51 TO STRINGER 65
(SHEET 3 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  33 of 54

### Page 34 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
• TYPICAL CRACK
C-C
2322435
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO LEFT WING
SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00 FROM STRINGER
51 TO STRINGER 65
(SHEET 4 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  DC8-57-104
Work - See page 1 for details.  34 of 54

### Page 35

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each inspection location.
MORE DATAQTYNAMETASKSTEP
16FastenersRemove1
(a)16WingInspect2
(a) Do an ETHF inspection for cracks at the open fastener holes in accordance with DC-8 NDTSPM 06-10-
01.003 Procedure 3.
NOTE: THE RELEVANT SIGNAL INDICATIONS SHOWN IN THE NDTSPM PROCEDURE ARE FOR A
"MANUAL" INSPECTION TECHNIQUE.
A RELEVANT SIGNAL INDICATION - WHEN USING AN AUTOMATED ROTATING PROBE SYSTEM
- WILL BE IN THE SHAPE OF A, "W", WITH LIFT-OFF SIGNAL (SET DURING CALIBRATION)
GENERALLY POSITIONED HORIZONTALLY.
FIGURE 1: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO LEFT WING
SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= 408.00 FROM STRINGER
51 TO STRINGER 65
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
35 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 36 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
ALL STRINGER
LOCATIONS SHOWN
(TYPICAL)
FRONT
SPAR
Хrs=393
STGR 65
Xw=408
STGR 64
STGR 63
STGR 62  XrS=  :428
CENTER
SPAR
STGR 61
STGR 60
LOOKING DOWN AT WING LOWER SKIN SURFACE  2315467
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW=-408.00 FROM
STRINGER 51 TO STRINGER 65
(SHEET 1 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.

### Page 37 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
ALL STRINGER
LOCATIONS SHOWN
STGR 59
(TYPICAL)
INBD
STGR 58
Xrs=428
STGR 57
STGR 56
STGR 55
STGR 54
STGR 53
STGR 52
STGR 51
REAR
SPAR
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW=-408.00 FROM
STRINGER 51 TO STRINGER 65
(SHEET 2 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  37 of 54

### Page 38 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
16 LOCATIONS 1
CENTER LINE STRINGER  STRINGER SPLICE
TYPICAL  FITTING
WING STRINGER
B
ENSPECTION  ETHF
C *
STRINGER SPLICE
FITTING
• SKIN
WING  WING
STRINGER  C  STRINGER  C
A-A  B-B  2322810
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW=-408.00 FROM
STRINGER 51 TO STRINGER 65
(SHEET 3 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  38 of 54

### Page 39 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
• TYPICAL CRACK
C-C
2322820
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW=-408.00 FROM
STRINGER 51 TO STRINGER 65
(SHEET 4 OF 5)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  39 of 54

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each inspection location.
MORE DATAQTYNAMETASKSTEP
16FastenersRemove1
(a)16WingInspect2
(a) Do an ETHF inspection for cracks at the open fastener holes in accordance with DC-8 NDTSPM 06-10-
01.003 Procedure 3.
NOTE: THE RELEVANT SIGNAL INDICATIONS SHOWN IN THE NDTSPM PROCEDURE ARE FOR A
"MANUAL" INSPECTION TECHNIQUE.
A RELEVANT SIGNAL INDICATION - WHEN USING AN AUTOMATED ROTATING PROBE SYSTEM
- WILL BE IN THE SHAPE OF A, "W", WITH LIFT-OFF SIGNAL (SET DURING CALIBRATION)
GENERALLY POSITIONED HORIZONTALLY.
FIGURE 2: ETHF INSPECTION FOR CRACKS AT THE OPEN FASTENER HOLES COMMON TO RIGHT
WING SKIN, WING STRINGERS, AND STRINGER SPLICE FITTING AT STATION XW= -408.00 FROM
STRINGER 51 TO STRINGER 65
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
40 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 41 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
/ FRONT
SPAR
Xrs=393
- STGR 65
→ STGR 64
- STGR 63
STGR 62
CENTEF
SPAF
•STGR 61
• STGR 60
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 3: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 1 OF 3)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  41 of 54

### Page 42 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
- STGR 59
Xw=408
Xrs=428  -STGR 58
+ STGR 57
-STGR 56
-STGR 55
-STGR 54
_STGR 53
- STGR 52
-STGR 51
— REAR
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 3: ETLE INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 2 OF 3)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  42 of 54

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATANAMETASKSTEP
(a)WingInspect1
(a) Do an ETLF inspection for cracks at the left wing external doubler modifications
outer perimeter of fasteners in accordance with DC-8 NDTSPM 06-10-02.001,
Procedure 1.
FIGURE 3: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
43 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 44 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
FRONT
SPAR
Xrs=393
STGR 65
XW=408
STGR 64
STGR 63
STGR 62  <rs=428
CENTER
SPAR
STGR 61
STGR 60
LOOKING DOWN AT WING LOWER SKIN SURFACE  2335409
FIGURE 4: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 1 OF 3)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  DC8-57-104
Work - See page 1 for details.  44 of 54

### Page 45 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
STGR 59
Xw=408
STGR 58  Xrs=428  INBD
STGR 57
STGR 56
STGR 55
STGR 54
STGR 53
STGR 52
STGR 51
REAR
SPAR
LOOKING DOWN AT WING LOWER SKIN SURFACE  2335410
FIGURE 4: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 2 OF 3)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  45 of 54

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATANAMETASKSTEP
(a)WingInspect1
(a) Do an ETLF inspection for cracks at the left wing external doubler modifications
outer perimeter of fasteners in accordance with DC-8 NDTSPM 06-10-02.001,
Procedure 1.
FIGURE 4: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
46 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 47 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
- FRONT
SPAR
Xrs=393
- STGR 65
-STGR 64
•STGR 63
STGR 62
CENTER
• SPAR
STGR 61
• STGR 60
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 5: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 1 OF 4)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  47 of 54

### Page 48 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
- STGR 59
Xrs=428  -STGR 58
- STGR 57
-STGR 56
-STGR 55
•STGR 54
-STGR 53
• STGR 52
-STGR 51
— REAR
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 5: ETLE INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 2 OF 4)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  DC8-57-104
Work - See page 1 for details.  48 of 54

### Page 49 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
Xw=408
0.100/0.125
REFERENCE
0.003+0.003  STANDARD
-0.002
- NOTCH
STRINGER
TYPICAL
~ FASTENER
PROBE
C
NULL/BALANCE
POINT  NOTCH/CRACK
INDICATION
LIFT OFF
IMPEDANCE PLANE DISPLAY
FIGURE 5: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 3 OF 4)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  49 of 54

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATANAMETASKSTEP
(a) (b) (c) (d)WingInspect1
(a) Flaw Detector (Impedance Plane Display) Nortec-2000D Olympus or equivalent.
(b) Eddy Current - Low Frequency - Probe SPO 2404 1KHz 100KHz Olympus or
equivalent.
(c) Locate reference standard parallel and next to the row of fasteners to be inspected
and locate nonconductive template over fastener and scan clockwise.
(d) The EDM notch is to be installed in the plate representing the wing skin layer; below
the (repair) doubler.
FIGURE 5: ETLF INSPECTION FOR CRACKS AT THE LEFT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = 408.00
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
50 of 54
BOEING SERVICE BULLETIN DC8-57-104

### Page 51 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
This Figure applies only to: Group 1-3, Configuration 2.
FRONT\
SPAR
Xrs=393
STGR 65
XW=408
STGR 64
STGR 63
STGR 62  ‹rs=428
CENTER
SPAR
STGR 61
STGR 60 -
LOOKING DOWN AT WING LOWER SKIN SURFACE
FIGURE 6: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 1 OF 4)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  51 of 54

### Page 52 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
STGR 59
STGR 58  Xrs=428
INBD
STGR 57
STGR 56
STGR 55
STGR 54
STGR 53
STGR 52
STGR 51
REAR
SPAR~
LOOKING DOWN AT WING LOWER SKIN SURFACE  2335439
FIGURE 6: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 2 OF 4)
Original Issue: August 18, 2014
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
Work - See page 1 for details.  52 of 54

### Page 53 (OCR)

BOEING SERVICE BULLETIN DC8-57-104
Xw=408
-0.100/0.125
REFERENCE
STANDARD  0.003 +0.003
-0.002
NOTCH-
STRINGER
TYPICAL
FASTENER
PROBE
NULL/BALANCE
POINT  NOTCH/CRACK
INDICATION
LIFT OFF
IMPEDANCE PLANE DISPLAY
2335566
FIGURE 6: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 3 OF 4)
Original Issue: August 18, 2014
Export Controlled ECCN: 9E991 - BOEING  DC8-57-104
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  53 of 54

### Page 54

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATANAMETASKSTEP
(a) (b) (c) (d)WingInspect1
(a) Flaw Detector (Impedance Plane Display) Nortec-2000D Olympus or equivalent.
(b) Eddy Current - Low Frequency - Probe SPO 2404 1KHz 100KHz Olympus or
equivalent.
(c) Locate reference standard parallel and next to the row of fasteners to be inspected
and locate nonconductive template over fastener and scan clockwise.
(d) The EDM notch is to be installed in the plate representing the wing skin layer; below
the (repair) doubler.
FIGURE 6: ETLF INSPECTION FOR CRACKS AT THE RIGHT WING AND EXTERNAL DOUBLER
MODIFICATIONS OUTER PERIMETER OF FASTENERS AT STATION XW = -408.00
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 18, 2014
DC8-57-104
54 of 54
BOEING SERVICE BULLETIN DC8-57-104

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
