# Boeing Service Bulletin MD11-28-137: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2015-0248; AD 2016-04-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin MD11-28-137](https://openairdocs.org/service-documents/boeing/md11-28-137.md)
- Title as filed: U.S. DOT/FAA - SB-MD11-28-137-00
- Pages: 69
- PDF: https://openairdocs.org/files/sha256/ff/36/ff36415553981ab14f7257ee6ec3bd47f90a653ec0baef905ec1283063ea60b6
- Page: https://openairdocs.org/service-documents/boeing/md11-28-137/file/ff3641555398

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
MD11
Service Bulletin
Number: MD11-28-137
Original Issue: June 24, 2014
ATA System: 2800
SUBJECT: FUEL - Fuel - Change Fuel Pump Control and Indication System Wiring
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2014 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: June 24, 2014
MD11-28-137
1 of 69
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
2 of 69
BOEING SERVICE BULLETIN MD11-28-137
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 0
B. Concurrent Requirements ...................................... 1 0
C. Reason ................................................ 1 1
D. Description .............................................. 1 1
E. Compliance .............................................. 1 2
F. Approval ............................................... 1 2
G. Manpower .............................................. 1 2
H. Weight and Balance Changes .................................... 1 3
I. Electrical Load Data ......................................... 1 4
J. References .............................................. 2 0
1. Existing Data: ......................................... 2 0
2. Data Supplied with this Service Bulletin: ........................... 2 0
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 0
4. Process Data: ......................................... 2 1
K. Publications Affected ........................................ 2 1
L. Interchangeability and Intermixability of Parts ........................... 2 1
M. Software Accomplishment Summary ................................ 2 1
2. MATERIAL INFORMATION ........................................ 2 3
A. Material - Price and Availability ................................... 2 3
B. Industry Support Information .................................... 2 3
C. Parts Necessary for Each Airplane ................................. 2 3
1. Kits/Parts ............................................ 2 3
2. Parts and Materials Supplied by the Operator ........................ 2 9
3. Parts Modified and Reidentified ................................ 2 9
4. Parts Removed and Not Replaced .............................. 2 9
D. Parts Necessary to Change Spares ................................. 2 9
E. Special Tooling - Price and Availability ............................... 2 9
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 9
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 1
A. GENERAL INFORMATION ..................................... 3 1
B. WORK INSTRUCTIONS ....................................... 3 3
APPENDIX A: FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
.................................................. 3 6
APPENDIX B: INPUT SURVEY ........................................ 6 9
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
3 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
4 of 69
BOEING SERVICE BULLETIN MD11-28-137
BLANK PAGE

### Page 5

Commercial 
Airplanes
MD11
Service Bulletin
SummaryNumber: MD11-28-137Original Issue: June 24, 2014
ATA System: 2800
SUBJECT: FUEL - Fuel - Change Fuel Pump Control and Indication System Wiring
CONCURRENT REQUIREMENTS
Refer to Paragraph 1.B., Concurrent Requirements.
BACKGROUND
Frictional heating or sparking resulting from fuel pump failure, wear of fuel pump rotating components, or ingestion
of debris by the fuel pump may result in development of a fuel tank ignition source. Frictional heating or sparking
in fuel pump inlets or priming system outlets exposed (i.e. not covered by fuel) to the tank ullage in combination
with the ullage being flammable, may result in a fuel tank ignition event. Center wing auxiliary, tail, and fuselage
auxiliary fuel tanks may be subject to this condition since they are normally pumped dry over the course of a
mission. A fuel tank ignition event could develop with a fuel pump running in an empty tank if the normal shutoff
command is delayed or as a result of control system failures that keep the fuel pump in a latent uncommanded
running condition. To ensure a timely fuel pump shutoff command revise flight crew shutoff procedures for center
wing auxiliary, tail, and fuselage auxiliary fuel pumps. To address the latent fuel pump uncommanded running
condition change center wing auxiliary, tail, and fuselage auxiliary fuel pump control and indication system wiring
to detect and indicate fuel pump uncommanded running conditions. If not corrected, a fuel pump running in an
empty fuel tank may result in a fuel tank ignition event.
This service bulletin is the result of the safety assessments conducted by Boeing under a Special Federal Aviation
Regulation (SFAR) 88, Fuel Tank System Fault Tolerance Evaluation Requirements.
Boeing Fleet Team Digest (FTD) MD-11 FTD 28-03006 and MD-11 FTD 28-13001 are related to this service
bulletin.
ACTION
This service bulletin changes fuel pump control and indication system wiring to detect and indicate fuel pump
uncommanded running conditions.
EFFECTIVITY
MD-11 and MD-11F Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-08-23 is related to this service bulletin.
Boeing recommends that the change given in this service bulletin be done within 60 months after the effective
date of AD 2013-08-23.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
5 of 69

### Page 6

INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Operators are encouraged to complete the survey provided in APPENDIX B of this service bulletin to help Boeing
predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
6 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 7 (OCR)

BOEING SERVICE BULLETIN MD11-28-137
CENTER ACCESSORY
COMPARTMENT
FORWARD CARGO
COMPARTMENT
RIGHT SIDE
AIR CONDITIONING
COMPARTMENT
RIGHT SIDE
ELECTRICAL
POWER CENTER
FORWARD CARGO
COMPARTMENT
LEFT SIDE
LOWER NOSE  AIR CONDITIONING
AND AVIONICS  COMPARTMENT  LEFT SIDE  COMPARTMENT
CHANGE FUEL PUMP CONTROL  1857655
AND INDICATION SYSTEM WIRING
Original Issue: June 24, 2014
Export Controlled ECCN: 9E991 - BOEING  MD11-28-137
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  7 of 69

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
8 of 69
BOEING SERVICE BULLETIN MD11-28-137
BLANK PAGE

### Page 9

Commercial 
Airplanes
MD11
Service Bulletin
Number: MD11-28-137
Original Issue: June 24, 2014
ATA System: 2800
SUBJECT: FUEL - Fuel - Change Fuel Pump Control and Indication System Wiring
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
MD-11 and MD-11F Airplanes that change fuel pump control and
indication system wiring to detect and indicate uncommanded fuel
pump running conditions in accordance with SR11280077-7001,
-7002 and SR11280083-7001 drawing configurations.
-1
MD-11 Airplanes that change fuel pump control and indication system
wiring to detect and indicate uncommanded fuel pump running
conditions in accordance with SR11280077-7003, -7004 and
SR11280083-7003 drawing configurations.
-2
MD-11 and MD-11F Airplanes that change fuel pump control and
indication system wiring to detect and indicate uncommanded fuel
pump running conditions in accordance with SR11280077-7005,
-7006 and SR11280083-7005 drawing configurations.
-3
Airplane Models:
MD-11, MD-11F
GroupFuselage Num-
ber
1447 - 449
1451 - 459
1460 - 464
1466 - 469
1470 - 479
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
9 of 69

### Page 10

GroupFuselage Num-
ber
1480 - 489
1491 - 499
1500 - 509
1510 - 517
1519
1520 - 529
1530 - 531
2532
1533 - 539
1540 - 543
2544
1545 - 549
1550 - 552
1554 - 559
1560 - 569
1570 - 579
1580 - 589
1590 - 596
3597 - 599
3600 - 609
3610 - 619
3620 - 629
3630 - 639
3640 - 646
2. Spares Affected
None.
B. Concurrent Requirements
The service bulletin listed below must be done before or at the same time as this service bulletin:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
10 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 11

DescriptionService BulletinCompany
Replace Fuel Pump Control Relays with Fault Current
Detectors and Change Fuel Tank Boost/Transfer Pump
Wire Termination
MD11-28A133
Original Issue
The Boeing Company
C. Reason
Frictional heating or sparking resulting from fuel pump failure, wear of fuel pump rotating components,
or ingestion of debris by the fuel pump may result in development of a fuel tank ignition source. Frictional
heating or sparking in fuel pump inlets or priming system outlets exposed (i.e. not covered by fuel) to
the tank ullage in combination with the ullage being flammable, may result in a fuel tank ignition event.
Center wing auxiliary, tail, and fuselage auxiliary fuel tanks may be subject to this condition since they
are normally pumped dry over the course of a mission. A fuel tank ignition event could develop with a
fuel pump running in an empty tank if the normal shutoff command is delayed or as a result of control
system failures that keep the fuel pump in a latent uncommanded running condition. To ensure a timely
fuel pump shutoff command revise flight crew shutoff procedures for center wing auxiliary, tail, and
fuselage auxiliary fuel pumps. To address the latent fuel pump uncommanded running condition change
center wing auxiliary, tail, and fuselage auxiliary fuel pump control and indication system wiring to
detect and indicate fuel pump uncommanded running conditions. If not corrected, a fuel pump running
in an empty fuel tank may result in a fuel tank ignition event.
This service bulletin is the result of the safety assessments conducted by Boeing under a Special
Federal Aviation Regulation (SFAR) 88, Fuel Tank System Fault Tolerance Evaluation Requirements.
Boeing Fleet Team Digest (FTD) MD-11 FTD 28-03006 and MD-11 FTD 28-13001 are related to this
service bulletin.
D. Description
This service bulletin changes fuel pump control and indication system wiring to detect and indicate fuel
pump uncommanded running conditions.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1, 3:
Affected Maintenance Zones
ZoneModel
112, 113, 114, 121, 122, 123, 125, 126, 127,
131, 132
MD-11, MD-11F
Group 2:
Affected Maintenance Zones
ZoneModel
112, 113, 114, 121, 122, 123, 125, 126, 127,
131, 132
MD-11
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
11 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 12

E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-08-23 is related to this service
bulletin.
Boeing recommends that the change given in this service bulletin be done within 60 months after the
effective date of AD 2013-08-23.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
In addition, the Manager of the FAA Los Angeles Aircraft Certification Office approves the action (i.e.
inspection or modification) defined in this service bulletin as an Alternative Method of Compliance
(AMOC) to the requirements of paragraph (g)(2) and (g)(4) of AD 2013-08-23. All provisions of AD
2013-08-23 that are not specifically referenced in the above statement remain fully applicable and must
be complied with.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
3.06.02Open Access
0.61.22Install Hardware
42.484.82Route and Terminate
Wiring
3.06.02Close Access
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
12 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 13

Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
0.51.02Test
49.599.0TOTAL FOR EACH AIRPLANE
Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
3.06.02Open Access
1.32.62Install Hardware
73.3146.62Route and Terminate
Wiring
3.06.02Close Access
0.51.02Test
81.1162.2TOTAL FOR EACH AIRPLANE
Group 3:
Elapsed HoursTask HoursNumber of PersonsTask
3.06.02Open Access
0.61.22Install Hardware
42.084.02Route and Terminate
Wiring
3.06.02Close Access
0.51.02Test
49.198.2TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Group 1:
Moment Change
(MEW) IN.-LBS
Mfr's Empty Weight
(MEW) LBS
Approximate Station
(Inches)
Airplane
+3928.9+6.6595.3MD-11, MD-11F
Group 2:
Moment Change
(MEW) IN.-LBS
Mfr's Empty Weight
(MEW) LBS
Approximate Station
(Inches)
Airplane
+6473.5+11.0588.5MD-11
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
13 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 14

Group 3:
Moment Change
(MEW) IN.-LBS
Mfr's Empty Weight
(MEW) LBS
Approximate Station
(Inches)
Airplane
+3498.9+5.6624.8MD-11, MD-11F
I. Electrical Load Data
1. Direct Current DC Load Changes:
No DC loads added or deleted.
2. Alternating Current (AC) Load Changes:
a. Add AC loads by amounts shown below:
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-2
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1209)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
LWR AUX TK L PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5875A
CHAP
280
BUS
2B
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-2
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1207)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
UPR AUX TK L PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5880A
CHAP
280
BUS
2B
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
14 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 15

UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-2
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1207)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
UPR AUX TK L PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5880A
CHAP
280
BUS
2B
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
0.50.551010DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
UNITS
%OPR
1
100
E/NE
PHASE
E
A
VAC
PF
115
VAC-1
1
UNIT
LOAD
(W)
5
NOTES
(B1-497)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
L TAIL TANK PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5888A
CHAP
280
BUS
1A
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
00000TAKEOFF & CLIMB
2.52.555050CRUISE COLD
2.52.555050CRUISE HOT
2.52.555050DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
15 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 16

UNITS
%OPR
1
100
E/NE
PHASE
E
A
VAC
PF
115
VAC
Emer
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1577)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
TAIL ALT PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
7000
CHAP
280
BUS
3A
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
00000TAKEOFF & CLIMB
0.250550CRUISE COLD
0.250550CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-1
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1206)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
UPR AUX TK R PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5878A
CHAP
280
BUS
1A
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
0.50.551010DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
16 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 17

UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-3
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1208)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
LWR AUX TK R PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5884A
CHAP
280
BUS
3C
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
UNITS
%OPR
1
100
E/NE
PHASE
E
A
VAC
PF
115
VAC-2
1
UNIT
LOAD
(W)
5
NOTES
(B1-496)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
R TAIL TANK PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
5889A
CHAP
280
BUS
2B
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
00000TAKEOFF & CLIMB
2.52.555050CRUISE COLD
2.52.555050CRUISE HOT
2.52.555050DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
17 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 18

Group 2:
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-1
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1645)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
FWD AUX-1 L PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
7001
CHAP
280
BUS
1A
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Group 2:
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-1
1
UNIT
LOAD
(W)
5
NOTES
(B1-542)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
FWD AUX-2 L PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
7002
CHAP
280
BUS
1A
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
18 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 19

Group 2:
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-3
1
UNIT
LOAD
(W)
5
NOTES
(B1-
1644)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
FWD AUX-1 R PUMP
SLAVE RELAY
5D0123-1
ITEM
500X
R2-
7003
CHAP
280
BUS
3C
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Group 2:
UNITS
%OPR
1
100
E/NE
PHASE
E
C
VAC
PF
115
VAC-3
1
UNIT
LOAD
(W)
5
NOTES
(B1-543)
SUPPLIER
DACO
EQUIPMENT NAME
PART NUMBER
FWD AUX-2 R PUMP
SLAVE RELAY
5D0123-1
ITEM
5002
R2-
7004
CHAP
280
BUS
3C
AVERAGE WATTS% TIME OPR
15/30 M2/5 M5 S15/30 M2/5 MCONDITION
00000LOADING
00000START
00000TAXI
555100100TAKEOFF & CLIMB
555100100CRUISE COLD
555100100CRUISE HOT
00000DESCENT & LAND
00000EMERGENCY
00000GROUND SERVICE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
19 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 20

b. Delete AC loads by amounts shown below:
No AC loads deleted.
J. References
1. Existing Data:
a. Boeing Service Bulletin MD11-28A133.
b. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2013-08-23.
c. Standard Overhaul Practices Manual (SOPM) 20-50-01.
d. Standard Wiring Practices Manual (SWPM) 20-00-09, 20-00-13, 20-00-16, 20-10-04, 20-20-02,
20-20-03, 20-31-00, 20-40-01 and 20-50-01.
e. MD11 Aircraft Maintenance Manual (AMM) 06-31-00, 06-31-06, 06-31-08, 24-40-00, 28-22-01
and 52-31-00.
f. MD-11 Fleet Team Digest (FTD) 28-03006 and 28-13001.
g. MD-11 Structural Repair Manual (SRM) 51.
2. Data Supplied with this Service Bulletin:
No data is supplied with this service bulletin. To obtain the data necessary to support this service
bulletin submit a data request to:
Data and Services Management
Mail Code: 110-SE20 (bldg 80)
2201 Seal Beach Blvd.
Seal Beach, California 90740 USA
Phone: (562) 797-1717
Fax: (562) 797-3783
E-mail: lbd.dataservicesmanagement@boeing.com
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No
-BDWGELEC INSTL - FUEL PUMP UNCOMMAND-
ED SIGNAL
SR11280077
-ADWGWIRE INSTL - FUEL PUMP UNCOMMAND-
ED SIGNAL
SR11280083
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
20 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 21

4. Process Data:
Douglas Process Specifications referred to on the drawings are not given in this service bulletin
since these procedures are frequently used as standard shop practices.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
28-22Aircraft Maintenance Manual
Section 1 and 3FAA Approved Flight Manual
28-02, 28-14, 28-22Fault Isolation Manual
Volumes I, II & IIIFlight Crew Operations Manual
MDC-02K1003 (ALI 28-4)Special Compliance Item Report
28-21, 28-22, 28-44Wiring Diagram Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated this service bulletin for effects on Fatigue Critical Structure (FCS) and for
changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This
service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
21 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 22

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
22 of 69
BOEING SERVICE BULLETIN MD11-28-137
BLANK PAGE

### Page 23

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane. Operators
are encouraged to share schedule requirements with Boeing for incorporation of the service bulletin.
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPON-
DER AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFOR-
MATION
Unit Price as of the original is-
sue date of this Service Bulletin
(US Dollars)
ROLT as of the original issue
date of this Service Bulletin
(Calendar Days)
NameKit Number
$14,149.00120Service KitSB11280137-3
$17,765.00120Service KitSB11280137-5
$14,856.00120Service KitSB11280137-7
Operators are encouraged to complete the survey provided in APPENDIX B of this service bulletin to
help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
B. Industry Support Information
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each airplane.
Group 1:
SB11280137-3
NotesNameQTYPart Number
(a)SCREW143D0005-04-9
(a)SCREW63D0005-08-11
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
23 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 24

Group 1:
SB11280137-3
NotesNameQTYPart Number
(a)CLIPNUT143D0191-04
(a)TERM BLOCK55D0010-15
(a)SOCKET75D0021-2
(a)TERM BLOCK15D0107-1
(a)RELAY75D0123-1
LOCKWASHER6MS35338-42
WASHER14NAS1252-4L
WASHER6NAS1252-8L
RIVNUT6NAS1329S08K75
(b)WIRE KIT1SR11280077-101
(b)WIRE KIT1SR11280077-104
(b)WIRE KIT1SR11280077-108
(b)WIRE KIT1SR11280077-112
(b)WIRE KIT1SR11280077-114
(b)WIRE KIT1SR11280077-116
(b)WIRE KIT1SR11280077-117
(b)WIRE KIT1SR11280077-119
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Refer to Wire Kit Table below for Wire Kit Contents.
Group 1:
Wire Kit Table
-119-117-116-114-112-108-104-101SR11280077
NotesNameQTYPart Number
(a)TERMINAL LUG 76425D0086-24
(a)TERMINAL LUG 76615D0086-26
(a)TERMINAL LUG 87835D0086-3
(a)TERMINAL LUG 7612645D0086-5
(a)TERMINAL LUG 76213245D0086-6
(b)WIRE CODE 80132
FT.
24
FT.
D2426-1C-16NM
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
24 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 25

Group 1:
Wire Kit Table
-119-117-116-114-112-108-104-101SR11280077
NotesNameQTYPart Number
(b)WIRE CODE 801100
FT.
11
FT.
29
FT.
20
FT.
250
FT.
250
FT.
255
FT.
50
FT.
D2426-1C-20NM
(b)WIRE CODE 80152
FT.
D2426-1C-22NM
(b)WIRE CODE 80120
FT.
D2426-1C-24NM
PIN, T/C 113124DC38-16P
PIN, T/C 11263132433DC38-20P
SKT T/C 11232281DC39-16S
SKT T/C 1124766DC39-20S
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Or approved alternate. Refer to SWPM 20-00-13.
Group 2:
SB11280137-5
NotesNameQTYPart Number
(a)SCREW223D0005-04-9
(a)SCREW163D0005-08-11
(a)SCREW23D0005-3-11
(a)CLIPNUT223D0191-04
(a)TERM BLOCK15D0010-13
(a)TERM BLOCK85D0010-15
(a)SOCKET115D0021-2
(a)TERM BLOCK15D0107-1
(a)RELAY115D0123-1
LOCKWASHER16MS35338-42
LOCKWASHER2MS35338-43
WASHER2NAS1252-10L
WASHER22NAS1252-4L
WASHER16NAS1252-8L
RIVNUT7NAS1329S08K75
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
25 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 26

Group 2:
SB11280137-5
NotesNameQTYPart Number
(b)WIRE KIT1SR11280077-102
(b)WIRE KIT1SR11280077-105
(b)WIRE KIT1SR11280077-107
(b)WIRE KIT1SR11280077-109
(b)WIRE KIT1SR11280077-111
(b)WIRE KIT1SR11280077-113
(b)WIRE KIT1SR11280077-115
(b)WIRE KIT1SR11280077-116
(b)WIRE KIT1SR11280077-118
(b)WIRE KIT1SR11280077-120
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Refer to Wire Kit Table below for Wire Kit Contents.
Group 2:
Wire Kit Table
-120-118-116-115-113-111-109-107-105-102SR11280077
NotesNameQTYPart Number
(a)DIODE25D0013-2A
(a)TERMINAL
LUG 764
25D0086-24
(a)TERMINAL
LUG 766
15D0086-26
(a)TERMINAL
LUG 878
35D0086-3
(a)TERMINAL
LUG 761
6685D0086-5
(a)TERMINAL
LUG 762
334625D0086-6
(b)WIRE CODE
801
32
FT.
24
FT.
D2426-1C-
16NM
(b)WIRE CODE
801
150
FT.
33
FT.
29
FT.
39
FT.
334
FT.
84
FT.
334
FT.
85
FT.
349
FT.
236
FT.
D2426-1C-
20NM
(b)WIRE CODE
801
108
FT.
42
FT.
D2426-1C-
22NM
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
26 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 27

Group 2:
Wire Kit Table
-120-118-116-115-113-111-109-107-105-102SR11280077
NotesNameQTYPart Number
(b)WIRE CODE
801
20
FT.
D2426-1C-
24NM
PIN, T/C 1131314DC38-16P
PIN, T/C 11266233611557DC38-20P
SKT T/C 1123121369DC39-16S
SKT T/C 11241011813DC39-20S
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Or approved alternate. Refer to SWPM 20-00-13.
Group 3:
SB11280137-7
NotesNameQTYPart Number
(a)SCREW23D0005-08-10
(a)SCREW63D0005-08-11
(a)NUT-CLIP23D0039-8
(a)RELAY75D0123-1
RELAY SOCKET765009-020-513
RELAY SOCKET165009-021-513
(a)BRACKET29D0062-3-08-08
PIN T/C 11451M39029/1-102
RIVET4MS20470AD4-3D
LOCKWASHER6MS35338-42
WASHER6NAS1252-8L
RIVNUT6NAS1329S08K75
CLAMP2NMC1001-2
(b)WIRE KIT1SR11280077-103
(b)WIRE KIT1SR11280077-106
(b)WIRE KIT1SR11280077-110
(b)WIRE KIT1SR11280077-112
(b)WIRE KIT1SR11280077-114
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
27 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 28

Group 3:
SB11280137-7
NotesNameQTYPart Number
(b)WIRE KIT1SR11280077-116
(b)WIRE KIT1SR11280077-117
(b)WIRE KIT1SR11280077-119
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Refer to Wire Kit Table below for Wire Kit Contents.
Group 3:
Wire Kit Table
-119-117-116-114-112-110-106-103SR11280077
NotesNameQTYPart Number
(a)TERMINAL LUG 76425D0086-24
(a)TERMINAL LUG 76615D0086-26
(a)TERMINAL LUG 7612645D0086-5
(a)TERMINAL LUG 7621325D0086-6
(a)PIN T/C 1005145D0187-2222P
PIN T/C 5798617240
SOCKET T/C 57834617340
(b)WIRE CODE 80125
FT.
24
FT.
D2426-1C-16NM
(b)WIRE CODE 801100
FT.
11
FT.
29
FT.
20
FT.
250
FT.
250
FT.
188
FT.
50
FT.
D2426-1C-20NM
(b)WIRE CODE 801126
FT.
D2426-1C-24NM
PIN, T/C 11312DC38-16P
PIN, T/C 112631324DC38-20P
SKT T/C 11232DC39-16S
SKT T/C 1124733DC39-20S
PIN T/C 114734M39029/1-101
PIN T/C 11452M39029/1-102
CONTACT28M39029/22-193
(a) Or approved equivalent. Refer to AEPL Drawing 7595071.
(b) Or approved alternate. Refer to SWPM 20-00-13.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
28 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 29

2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number / Specification
(a)TIE TAPEAs RequiredDMS 2089
(18XTZ), (23XTZ)
or
Equivalent
(a) Can be purchased from: Gudenbrod, Incorporated, 274 Shoemaker Road,
Pottstown, Pennsylvania, 19464, CAGE 82110
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
29 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 30

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
30 of 69
BOEING SERVICE BULLETIN MD11-28-137
BLANK PAGE

### Page 31

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY
ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE
PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE
CAN OCCUR.
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE
TO THE AIRPLANE OR EQUIPMENT.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Equivalent parts are listed in the AEPL, Drawing 7595071.
3. Use the approved fastener and process material substitutions, in accordance with
MD-11 SRM 51.
4. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards in SRM
Chapter 51 may be used. In addition, washers may be installed for fastener grip
length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
5. A 1/8-inch thick stack of the same type washers called for in this service bulletin is
the maximum thickness which may be used under fastener head or nut to counteract
accumulation of tolerances.
EXCEPTION: When the available fastener length increments are greater than
1/16-inch, a 3/16-inch thick stack of the same type washers may be used.
6. Unless shown differently, these dimensions and tolerances are used:
 Linear dimensions are in inches.
 Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch.
 Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch.
 Angular tolerance is plus or minus 2 degrees.
 Hole dimensions for standard solid rivets are in MD-11 SRM 51.
 Torque limits to tighten nuts and bolts are in MD-11 SRM 51.
7. Refer to these SWPM chapters for applicable operations, as accepted procedures:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
31 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 32

TitleChapter
GENERAL MAINTENANCE PRACTICES - ELECTRICALSWPM 20-00-09
ELECTRICAL WIRE CODESSWPM 20-00-13
ELECTRICAL WIRE END TERMINATION CODES AND TOOL
CODES
SWPM 20-00-16
COIL AND STOW - MAINTENANCE PRACTICESSWPM 20-10-04
TERMINAL BLOCKS - MAINTENANCE PRACTICESSWPM 20-20-02
GENERAL INSTALLATIONS HARDWARE - MAINTENANCE
PRACTICES
SWPM 20-20-03
ELECTRICAL CONNECTORS - MAINTENANCE PRACTICESSWPM 20-31-00
POWER DISTRIBUTION BUS - MAINTENANCE PRACTICESSWPM 20-40-01
ELECTRICAL BONDING - MAINTENANCE PRACTICESSWPM 20-50-01
8. Obey all of the warnings and cautions given in the specified manual sections.
9. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
10. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U' or 'Y' in place of the '-' (dash) in the part number. It is permitted
to install parts identified with a 'U' or 'Y' as an alternative to the '-' (dash) number
part. Boeing Drawing SE10000000, Sheets 5.0 and 6.0 contain more data.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
13. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
14. Review and understand all general notes of Service Rework Drawings that follow:
SheetsService Rework Drawing
3, 3.1, 3.2, 3.3, 3.4SR11280077
1SR11280083
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
32 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 33

B. WORK INSTRUCTIONS
1. Gain access:
a. Open access doors in the table as follow:
Location/DescriptionReferenceAccess Door
Avionics Equipment CompartmentMD11 AMM 06-31-00112AB
Left-side Air-conditioning Compartment113AL
113DL
Right-side Air-conditioning Compartment114AR
Center Accessory Compartment131AB
b. Open forward cargo compartment door. Refer to MD11 AMM 52-31-00 as an accepted
procedure.
c. Remove/Keep forward cargo compartment ceiling panels and attaching hardware right and
left sides between stations Y=595.000 and Y=673.500. Refer to MD11 AMM 06-31-06 and
MD11 AMM 06-31-08.
2. Install relays and hardware in accordance with the table(s) as follow:
Group 1:
SheetsDrawing
13, 14, 22, 24, 25SR11280077-7001
Group 2:
SheetsDrawing
15, 16, 18, 20, 21, 22, 23, 24, 25, 26, 27SR11280077-7003
Group 3:
SheetsDrawing
17, 18, 19, 22, 24, 25SR11280077-7005
3. Route wiring in accordance with the table(s) as follow:
Group 1:
Additional DataSheet(s)Drawing
1, 4.1, 5, 6, 7, 8, 9, 10SR11280083
Views C, B-B, FORWARD EQUIPMENT RACK2SR11280083
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
33 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 34

Group 1:
Additional DataSheet(s)Drawing
Views N, F-F, G-G, D3SR11280083
Views AL-AL, AM for -7001, AN, AP11SR11280083
Group 2:
Additional DataSheet(s)Drawing
1, 2, 4.1, 5, 6, 7, 8, 9, 10SR11280083
Views N, F-F, G-G, D3SR11280083
Views AL-AL, AM for -7003, AN, AP11SR11280083
Group 3:
Additional DataSheet(s)Drawing
1, 3, 4, 5, 6, 7, 8, 9, 10SR11280083
Views C, B-B, FORWARD EQUIPMENT RACK2SR11280083
Views AL-AL, AM for -7005, AN, AP11SR11280083
4. Change wiring in accordance with the table(s) as follow:
Group 1:
SheetsDrawing
6.8, 6.9, 6.10, 6.11, 6.12, 8, 101.201, 104.201, 104.202, 108.201,
112.201, 114.201, 116.201, 117.201, 119.201, 302.201
SR11280077-7001
Group 2:
SheetsDrawing
6.13, 6.14, 6.15, 6.16, 6.17, 6.18, 6.19, 6.20, 8, 102.201, 105.201,
105.202, 107.201, 109.201, 111.201, 113.201, 115.201, 116.201,
118.201, 120.201, 301.201, 303.201, 305.201
SR11280077-7003
Group 3:
SheetsDrawing
6.21, 6.22, 6.23, 6.24, 6.25, 6.26, 103.201, 106.201, 106.202,
110.201, 112.201, 114.201, 116.201, 117.201, 119.201, 304.201
SR11280077-7005
5. Test fuel pumps uncommanded on detection circuits as follow:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
34 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 35

Group 1, 3:
Perform Functional Test of the Fuel Pumps Uncommanded On Detection Circuit in accordance
with MD-11 AMM 28-22-01.
Group 2:
Perform Functional Test of the Fuel Pumps Uncommanded On Detection Circuit in accordance
with APPENDIX A.
6. Close access:
a. Install/Kept forward cargo compartment ceiling panels and attaching hardware right and left
sides between stations Y=595.000 and Y=673.500. Refer to MD11 AMM 06-31-06 and MD11
AMM 06-31-08.
b. Close forward cargo compartment door. Refer to MD11 AMM 52-31-00 as an accepted
procedure.
c. Close access doors in the table as follow:
Location/DescriptionReferenceAccess Door
Avionics Equipment CompartmentMD11 AMM 06-31-00112AB
Left-side Air-conditioning Compartment113AL
113DL
Right-side Air-conditioning Compartment114AR
Center Accessory Compartment131AB
7. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
35 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 36

1. Test equipment required:
a. Electrical jumper wire, 22 gauge, two feet in length with alligator clips at both ends large enough
to grasp Fault Current Detector (FCD) terminal posts.
b. Multimeter, with alligator clips at end of wire leads large enough to grasp FCD terminal posts.
2. Test set up:
a. Apply electrical power to the aircraft. Refer to MD-11 AMM 24-40-00 as an accepted procedure.
b. On the Systems Control Panel do as follows:
(1) Turn the six BRT knobs (15) to the middle position.
(2) Push the FUEL switchlight (16).
c. Adjust the applicable fuel quantities as follows:
(1) Total aux fuel quantity is less than 600 lb (272 kg).
(2) Forward aux tank (if installed) fuel quantity must be less than 200 lb (91 kg).
(3) Tail tank fuel quantity must be less than 300 lb (136 kg).
d. On the Fuel System Control Panel (FSCP) set the SYSTEM switchlight (17) to MANUAL and after
10 seconds verify the following on the FUEL synoptic page:
(1) All main tank forward and aft boost pumps (total of 7) are shown as ON (green or amber circle
and pump vanes).
(2) Upper Aux Left Pump is shown as ON (green or amber circle and pump vanes).
(3) Upper Aux Right Pump is shown as ON (green or amber circle and pump vanes).
(4) Lower Aux Left Pump is shown as ON (green or amber circle and pump vanes).
(5) Lower Aux Right Pump is shown as ON (green or amber circle and pump vanes).
(6) Tail Tank Left Pump is shown as ON (green or amber circle and pump vanes).
(7) Tail Tank Right Pump is shown as ON (green or amber circle and pump vanes).
e. On the FSCP push the 1 PUMPS, 2 PUMPS, 3 PUMPS, AUX TANKS L TRANS, AUX TANKS R
TRANS and TAIL TANK TRANS switches and verify the following on the FUEL synoptic page:
(1) All main tank forward and aft boost pumps (total of 7) are shown as OFF (white empty circle).
(2) Upper Aux Left Pump is shown as OFF (white empty circle).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 1 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
36 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 37

(3) Upper Aux Right Pump is shown as OFF (white empty circle).
(4) Lower Aux Left Pump is shown as OFF (white empty circle).
(5) Lower Aux Right Pump is shown as OFF (white empty circle).
(6) Tail Tank Left Pump is shown as OFF (white empty circle).
(7) Tail Tank Right Pump is shown as OFF (white empty circle).
NOTE: If other fuel pumps are shown as ON, push the applicable pump switch on the FSCP
until all fuel pumps are shown as OFF.
f. On the FWD AUX FUEL TANK switch panel, verify that the L TRANS and R TRANS switches are
OFF.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE CIRCUIT
BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY TO PERSONS
AND DAMAGE TO EQUIPMENT CAN OCCUR.
g. Open circuit breakers and install safety tags as follow:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP POWER TAIL TANK L XFRB1-157820B
FUEL PUMP POWER AUX TANK 1 L FWDB1-39421B
FUEL PUMP POWER AUX TANK 2 L FWDB1-164722B
FUEL PUMP POWER AUX TANK R UPRB1-125023B
FUEL PUMP POWER TANK 1 FWDB1-61424B
FUEL PUMP POWER TANK 2 FWDB1-60825B
FUEL PUMP POWER TANK 3 XFRB1-61826B
FUEL PUMP CONTROL TAIL TANK L XFRB1-49720E
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
FUEL PUMP CONTROL AUX TANK R UPRB1-120623E
FUEL PUMP CONTROL TANK 1 FWDB1-61524E
FUEL PUMP CONTROL TANK 2 FWDB1-60925E
FUEL PUMP CONTROL TANK 3 XFRB1-61926E
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 2 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
37 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 38

UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP POWER TAIL TANK R XFRB1-157620C
FUEL PUMP POWER AUX TANK L UPRB1-124822C
FUEL PUMP POWER AUX TANK L LWRB1-124923C
FUEL PUMP POWER TANK 1 XFRB1-61024C
FUEL PUMP POWER TANK 2 R AFTB1-59625C
FUEL PUMP POWER TANK 3 AFTB1-62026C
FUEL PUMP CONTROL TAIL TANK R XFRB1-49621F
FUEL PUMP CONTROL AUX TANK L UPRB1-120722F
FUEL PUMP CONTROL AUX TANK L LWRB1-120923F
FUEL PUMP CONTROL TANK 1 XFRB1-61124F
FUEL PUMP CONTROL TANK 2 R AFTB1-60325F
FUEL PUMP CONTROL TANK 3 AFTB1-62126F
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP POWER AUX TANK 1 R FWDB1-39321D
FUEL PUMP POWER AUX TANK 2 R FWDB1-164622D
FUEL PUMP POWER AUX TANK R LWRB1-125123D
FUEL PUMP POWER TANK 1 AFTB1-61224D
FUEL PUMP POWER TANK 2 XFRB1-75625D
FUEL PUMP POWER TANK 3 FWDB1-61626D
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
FUEL PUMP CONTROL AUX TANK 2 R FWDB1-54322G
FUEL PUMP CONTROL AUX TANK R LWRB1-120823G
FUEL PUMP CONTROL TANK 1 AFTB1-61324G
FUEL PUMP CONTROL TANK 2 XFRB1-75725G
FUEL PUMP CONTROL TANK 3 FWDB1-61726G
3. Test procedure - Fuel Pumps Uncommanded On Detection Circuit Functional Test:
a. Upper Aux Left Pump (M1-1934) Test:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 3 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
38 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 39

(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-2, remove
the terminal shield of FCD U1-702 (1) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-2 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-702 (1).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L UPRB1-120722F
(4) On the FUEL synoptic page, verify the Upper Aux Left Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Upper Aux Left Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L UPRB1-120722F
(6) On the FUEL synoptic page verify the Upper Aux Left Pump is shown in as OFF (white empty
circle).
(7) At the CAC EPC Bay-2 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-702 (1).
(8) At the CAC EPC Bay-2 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-702 (1) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 4 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
39 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 40

UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L UPRB1-120722F
(10) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-702 (1)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-702 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the AUX TANKS L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-702 (1)
reads less than 10 volts.
(b) On the FUEL synoptic page the Upper Aux Left Pump is shown as ON (amber circle and
pump vanes).
(12) On the FSCP, push the AUX TANKS L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-702 (1)
reads more than 110 volts.
(b) On the FUEL synoptic page the Upper Aux Left Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L UPRB1-120722F
(14) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-702 (1)
reads less than 10 volts.
(15) At the CAC EPC Bay-2 remove the multimeter lead from terminal stud 12 of FCD U1-702 (1).
(16) At the CAC EPC Bay-2 install the terminal shield (14) on FCD U1-702 (1) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 5 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
40 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 41

b. Upper Aux Right Pump (M1-1933) Test:
(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-1, remove
the terminal shield of FCD U1-701 (2) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-1 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-701 (2).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R UPRB1-120623E
(4) On the FUEL synoptic page, verify the Upper Aux Right Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Upper Aux Right Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R UPRB1-120623E
(6) On the FUEL synoptic page verify the Upper Aux Right Pump is shown in as OFF (white empty
circle).
(7) At the CAC EPC Bay-1 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-701 (2).
(8) At the CAC EPC Bay-1 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-701 (2) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 6 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
41 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 42

UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R UPRB1-120623E
(10) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-701 (2)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-701 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the AUX TANKS R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-701 (2)
reads less than 10 volts.
(b) On the FUEL synoptic page the Upper Aux Right Pump is shown as ON (amber circle
and pump vanes).
(12) On the FSCP, push the AUX TANKS R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-701 (2)
reads more than 110 volts.
(b) On the FUEL synoptic page the Upper Aux Right Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R UPRB1-120623E
(14) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-701 (2)
reads less than 10 volts.
(15) At the CAC EPC Bay-1 remove the multimeter lead from terminal stud 12 of FCD U1-701 (2).
(16) At the CAC EPC Bay-1 install the terminal shield (14) on FCD U1-701 (2) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 7 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
42 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 43

c. Lower Aux Left Pump (M1-1936) Test:
(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-2, remove
the terminal shield of FCD U1-704 (3) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-2 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-704 (3).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L LWRB1-120923F
(4) On the FUEL synoptic page, verify the Lower Aux Left Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Lower Aux Left Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L LWRB1-120923F
(6) On the FUEL synoptic page verify the Lower Aux Left Pump is shown in as OFF (white empty
circle).
(7) At the CAC EPC Bay-2 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-704 (3).
(8) At the CAC EPC Bay-2 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-704 (3) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 8 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
43 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 44

UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L LWRB1-120923F
(10) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-704 (3)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-704 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the AUX TANKS L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-704 (3)
reads less than 10 volts.
(b) On the FUEL synoptic page the Lower Aux Left Pump is shown as ON (amber circle and
pump vanes).
(12) On the FSCP, push the AUX TANKS L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-704 (3)
reads more than 110 volts.
(b) On the FUEL synoptic page the Lower Aux Left Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK L LWRB1-120923F
(14) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-704 (3)
reads less than 10 volts.
(15) At the CAC EPC Bay-2 remove the multimeter lead from terminal stud 12 of FCD U1-704 (3).
(16) At the CAC EPC Bay-2 install the terminal shield (14) on FCD U1-704 (3) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 9 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
44 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 45

d. Lower Aux Right Pump (M1-1935) Test:
(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-3, remove
the terminal shield of FCD U1-703 (4) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-3 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-703 (4).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R LWRB1-120823B
(4) On the FUEL synoptic page, verify the Lower Aux Right Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Lower Aux Right Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R LWRB1-120823B
(6) On the FUEL synoptic page verify the Lower Aux Right Pump is shown in as OFF (white empty
circle).
(7) At the CAC EPC Bay-3 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-703 (4).
(8) At the CAC EPC Bay-3 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-703 (4) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 10 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
45 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 46

UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R LWRB1-120823B
(10) At the CAC EPC Bay-3 verify the multimeter attached to terminal stud 12 of FCD U1-703 (4)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-703 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the AUX TANKS R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-3 the multimeter attached to terminal stud 12 of FCD U1-703 (4)
reads less than 10 volts.
(b) On the FUEL synoptic page the Lower Aux Right Pump is shown as ON (amber circle
and pump vanes).
(12) On the FSCP, push the AUX TANKS R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-3 the multimeter attached to terminal stud 12 of FCD U1-703 (4)
reads more than 110 volts.
(b) On the FUEL synoptic page the Lower Aux Right Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK R LWRB1-120823B
(14) At the CAC EPC Bay-3 verify the multimeter attached to terminal stud 12 of FCD U1-703 (4)
reads less than 10 volts.
(15) At the CAC EPC Bay-3 remove the multimeter lead from terminal stud 12 of FCD U1-703 (4).
(16) At the CAC EPC Bay-3 install the terminal shield (14) on FCD U1-703 (4) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 11 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
46 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 47

e. Tail Tank Left Pump (M1-2802) Test:
(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-1, remove
the terminal shield of FCD U1-851 (5) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-1 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-851 (5).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK L XFRB1-49720E
(4) On the FUEL synoptic page, verify the Tail Tank Left Pump is shown as ON (amber circle and
pump vanes).
NOTE: If the Tail Tank Left Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK L XFRB1-49720E
(6) On the FUEL synoptic page verify the Tail Tank Left Pump is shown in as OFF (white empty
circle).
(7) At the CAC EPC Bay-1 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-851 (5).
(8) At the CAC EPC Bay-1 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-851 (5) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 12 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
47 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 48

UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK L XFRB1-49720E
(10) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-851 (5)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-851 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the TAIL TANK TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-851 (5)
reads less than 10 volts.
(b) On the FUEL synoptic page the Tail Tank Left Pump is shown as ON (amber circle and
pump vanes).
(12) On the FSCP, push the TAIL TANK TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-851 (5)
reads more than 110 volts.
(b) On the FUEL synoptic page the Tail Tank Left Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK L XFRB1-49720E
(14) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-851 (5)
reads less than 10 volts.
(15) At the CAC EPC Bay-1 remove the multimeter lead from terminal stud 12 of FCD U1-851 (5).
(16) At the CAC EPC Bay-1 install the terminal shield (14) on FCD U1-851 (5) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 13 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
48 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 49

f. Tail Tank Right Pump (M1-2800) Test:
(1) At the Center Accessory Compartment (CAC) Electrical Power Center (EPC) Bay-2, remove
the terminal shield of FCD U1-852 (6) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(2) At the CAC EPC Bay-2 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-852 (6).
(3) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK R XFRB1-49621F
(4) On the FUEL synoptic page, verify the Tail Tank Right Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Tail Tank Right Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(5) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK R XFRB1-49621F
(6) On the FUEL synoptic page verify the Tail Tank Right Pump is shown as OFF (white empty
circle).
(7) At the CAC EPC Bay-2 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-852 (6).
(8) At the CAC EPC Bay-2 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-852 (6) and verify that it reads less than 10 volts.
(9) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 14 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
49 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 50

UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK R XFRB1-49621F
(10) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-852 (6)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF FCD U1-852 TO BE POWERED
WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN CLEAR
OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR INJURY
COULD RESULT.
(11) On the FSCP, push the TAIL TANK TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-852 (6)
reads less than 10 volts.
(b) On the FUEL synoptic page the Tail Tank Right Pump is shown as ON (amber circle and
pump vanes).
(12) On the FSCP, push the TAIL TANK TRANS switch and verify as follows:
(a) At the CAC EPC Bay-2 the multimeter attached to terminal stud 12 of FCD U1-852 (6)
reads more than 110 volts.
(b) On the FUEL synoptic page the Tail Tank Right Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(13) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 2
NameNumberColumnRow
FUEL PUMP CONTROL TAIL TANK R XFRB1-49621F
(14) At the CAC EPC Bay-2 verify the multimeter attached to terminal stud 12 of FCD U1-852 (6)
reads less than 10 volts.
(15) At the CAC EPC Bay-2 remove the multimeter lead from terminal stud 12 of FCD U1-852 (6).
(16) At the CAC EPC Bay-2 install the terminal shield (14) on FCD U1-852 (6) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 15 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
50 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 51

g. Tail Altn Pump (M1-2801) Test:
(1) On the FUEL synoptic page, verify the Tail Altn Pump is shown as OFF (white empty circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(2) Open and tag circuit breakers as follow:
OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TANK 2 L AFTB1-68017G
FUEL PUMP TAIL TANK ALTNB1-157418G
(3) At the Avionics Compartment Forward Equipment Panel remove the terminal shield of FCD
U1-850 (7) as follows:
(a) Remove the two screws (12) and lockwashers (13) from the FCD terminal shield (14).
(b) Remove the terminal shield (14).
(4) At the Avionics Compartment Forward Equipment Panel connect the jumper wire from terminal
stud 11 to terminal stud 12 of FCD U1-850 (7).
(5) Close circuit breaker as follows:
OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TAIL TANK ALTNB1-157418G
(6) On the FUEL synoptic page, verify the Tail Tank Altn Pump is shown as ON (amber circle
and pump vanes).
NOTE: If the Tail Tank Altn Pump is not shown as ON, this indicates that there is a possible
wiring or component failure of the uncommanded on detection circuitry and
troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(7) Open circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 16 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
51 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 52

OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TAIL TANK ALTNB1-157418G
(8) On the FUEL synoptic page verify the Tail Tank Altn Pump is shown as OFF (white empty
circle).
(9) At the Avionics Compartment Forward Equipment Panel remove the jumper wire from terminal
stud 11 to terminal stud 12 of FCD U1-850 (7).
(10) At the Avionics Compartment Forward Equipment Panel attach the multimeter lead, set to
measure AC voltage, to terminal stud 12 of FCD U1-850 (7) and verify that it reads less than
10 volts.
WARNING: THE NEXT STEPS WILL CAUSE TERMINALS 12, A2, B2, C2, A1, B1, C1, AND X1
OF FCD U1-850 TO BE POWERED WITH 115 VAC POWER. PERSONNEL IN THE
AVIONICS COMPARTMENT SHOULD REMAIN CLEAR OF THESE EXPOSED
TERMINALS UNTIL POWER IS REMOVED OR INJURY COULD RESULT.
(11) Close circuit breaker as follows:
OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TAIL TANK ALTNB1-157418G
(12) At the Avionics Compartment Forward Equipment Panel verify the multimeter attached to
terminal stud 12 of FCD U1-850 (7) reads more than 110 volts.
(13) On the FSCP, push the TAIL TANK ALT PUMP switch and verify as follows:
(a) At the Avionics Compartment Forward Equipment Panel the multimeter attached to
terminal stud 12 of FCD U1-850 (7) reads less than 10 volts.
(14) On the FSCP, push the TAIL TANK ALT PUMP switch and verify as follows:
(a) At the Avionics Compartment Forward Equipment Panel the multimeter attached to
terminal stud 12 of FCD U1-850 (7) reads more than 110 volts.
(b) On the FUEL synoptic page the Tail Tank Altn Pump is shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(15) Open circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 17 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
52 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 53

OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TAIL TANK ALTNB1-157418G
(16) At the Avionics Compartment Forward Equipment Panel verify the multimeter attached to
terminal stud 12 of FCD U1-850 (7) reads less than 10 volts.
(17) At the Avionics Compartment Forward Equipment Panel remove the multimeter lead from
terminal stud 12 of FCD U1-850 (7).
(18) At the Avionics Compartment Forward Equipment Panel install the terminal shield (14) on
FCD U1-850 (7) as follows:
(a) Install the terminal shield (14) with two screws (12) and two lockwashers (13).
(19) Close circuit breakers as follow:
OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP TANK 2 L AFTB1-68017G
FUEL PUMP TAIL TANK ALTNB1-157418G
h. Forward Aux Tank Left Pumps (M1-1492 and M1-1494) Test:
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(1) Verify circuit breakers are open and tagged as follow:
OVERHEAD, RIGHT EMER AC BUS
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
(2) At the CAC EPC Bay-1 remove the terminal shields of FCDs U1-709 (8) and U1-790 (9) as
follow:
(a) Remove the two screws (12) and lockwashers (13) from each FCD terminal shield (14).
(b) Remove the terminal shields (14).
(3) At the CAC EPC Bay-1 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-709 (8).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 18 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
53 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 54

(4) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
(5) On the FUEL synoptic page, verify the two Fwd Aux Left Pumps are shown as ON (amber
circle and pump vanes).
(6) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the L TRANS
switch is illuminated.
NOTE: If the ON annunciator light in the L TRANS switch is not illuminated or the Fwd Aux
Left Pumps are not shown as ON, then there is a possible wiring or component failure
of the uncommanded on detection circuitry and troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(7) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
(8) On the FUEL synoptic page verify both Fwd Aux Left Pumps are shown as OFF (white empty
circle).
(9) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the L TRANS
switch is not illuminated.
(10) At the CAC EPC Bay-1 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-709 (8).
(11) At the CAC EPC Bay-1 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-709 (8) and verify that it reads less than 10 volts.
(12) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 19 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
54 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 55

(13) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-709 (8)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF THE FCD U1-709 TO BE
POWERED WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN
CLEAR OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR
INJURY COULD RESULT.
(14) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-709 (8)
reads less than 10 volts.
(b) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as ON (amber circle
and pump vanes).
(c) After approximately 20 - 30 seconds the multimeter reads more than 110 volts.
NOTE: If the voltage does not increase to more than 110 volts and remain there, then
there is a possible wiring or component failure of the uncommanded on detection
circuitry and troubleshooting is necessary.
1) Monitor the voltage for an additional minute and verify that the voltage does not drop
back below 10 volts at any time.
(15) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-709 (8)
reads more than 110 volts.
(b) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(16) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 L FWDB1-164521E
(17) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-709 (8)
reads less than 10 volts.
(18) At the CAC EPC Bay-1 remove the multimeter lead from terminal stud 12 of FCD U1-709 (8).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 20 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
55 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 56

(19) At the CAC EPC Bay-1 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-790 (9).
(20) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
(21) On the FUEL synoptic page, verify the two Fwd Aux Left Pumps are shown as ON (amber
circle and pump vanes).
(22) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the L TRANS
switch is illuminated.
NOTE: If the ON annunciator light in the L TRANS switch is not illuminated or the Left Forward
Aux Pumps are not shown as ON, then there is a possible wiring or component failure
of the uncommanded on detection circuitry and troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(23) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
(24) On the FUEL synoptic page verify both Fwd Aux Left Pumps are shown as OFF (white empty
circle).
(25) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the L TRANS
switch is not illuminated.
(26) At the CAC EPC Bay-1 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-790 (9).
(27) At the CAC EPC Bay-1 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-790 (9) and verify that it reads less than 10 volts.
(28) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 21 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
56 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 57

UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
(29) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-790 (9)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF THE FCD U1-790 TO BE
POWERED WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN
CLEAR OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR
INJURY COULD RESULT.
(30) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-790 (9)
reads less than 10 volts.
(b) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as ON (amber circle
and pump vanes).
(c) After approximately 20 - 30 seconds the multimeter reads more than 110 volts.
NOTE: If the voltage does not increase to more than 110 volts and remain there, then
there is a possible wiring or component failure of the uncommanded on detection
circuitry and troubleshooting is necessary.
1) Monitor the voltage for an additional minute and verify that the voltage does not drop
back below 10 volts at any time.
(31) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) At the CAC EPC Bay-1 the multimeter attached to terminal stud 12 of FCD U1-790 (9)
reads more than 110 volts.
(b) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(32) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 1
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 2 L FWDB1-54222E
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 22 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
57 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 58

(33) At the CAC EPC Bay-1 verify the multimeter attached to terminal stud 12 of FCD U1-790 (9)
reads less than 10 volts.
(34) At the CAC EPC Bay-1 remove the multimeter lead from terminal stud 12 of FCD U1-790 (9).
(35) At the CAC EPC Bay-1 install the terminal shields (14) on FCDs U1-709 (8) and U1-790 (9)
as follow:
(a) Install the terminal shields (14) with two screws (12) each and two lockwashers (13) each.
(36) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as ON (amber circle
and pump vanes).
(b) On the Fwd Aux Fuel Tank Overhead Panel the ON annunciator light in the L TRANS
switch is illuminated.
NOTE: If the ON annunciator light in the L TRANS switch is not illuminated or the Fwd
Aux Left Pumps are not shown as ON, verify that diode R7-361 is installed
correctly.
(37) On the Fwd Aux Fuel Tank Overhead Panel push the L TRANS switch and verify as follows:
(a) On the FUEL synoptic page both Fwd Aux Left Pumps are shown as OFF (white empty
circle).
(b) On the Fwd Aux Fuel Tank Overhead Panel the ON annunciator light in the L TRANS
switch is not illuminated.
i. Forward Aux Tank Right Pumps (M1-1491 and M1-1493) Test:
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(1) Verify circuit breakers are open and tagged as follow:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
FUEL PUMP CONTROL AUX TANK 2 R FWDB1-54322G
(2) At the CAC EPC Bay-3 remove the terminal shields of the FCDs U1-710 (10) and U1-789
(11) as follow:
(a) Remove the two screws (12) and lockwashers (13) from each FCD terminal shield (14).
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 23 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
58 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 59

(b) Remove the terminal shields (14).
(3) At the CAC EPC Bay-3 connect the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-710 (10).
(4) Close circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
(5) On the FUEL synoptic page, verify the two Fwd Aux Right Pumps are shown as ON (amber
circle and pump vanes).
(6) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the R TRANS
switch is illuminated.
NOTE: If the ON annunciator light in the R TRANS switch is not illuminated or the Forward
Aux Right Pumps are not shown as ON, then there is a possible wiring or component
failure of the uncommanded on detection circuitry and troubleshooting is necessary.
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(7) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
(8) On the FUEL synoptic page verify both Fwd Aux Right Pumps are shown as OFF (white empty
circle).
(9) On the Fwd Aux Fuel Tank Overhead Panel, verify the ON annunciator light in the R TRANS
switch is not illuminated.
(10) At the CAC EPC Bay-3 remove the jumper wire from terminal stud 11 to terminal stud 12 of
FCD U1-710 (10).
(11) At the CAC EPC Bay-3 attach the multimeter lead, set to measure AC voltage, to terminal
stud 12 of FCD U1-710 (10) and verify that it reads less than 10 volts.
(12) Close circuit breaker as follows:
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 24 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
59 of 69
BOEING SERVICE BULLETIN MD11-28-137

### Page 60

UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
(13) At the CAC EPC Bay-3 verify the multimeter attached to terminal stud 12 of FCD U1-710 (10)
reads more than 110 volts.
WARNING: THE NEXT STEP WILL CAUSE TERMINAL X1 OF THE FCD U1-710 TO BE
POWERED WITH 115 VAC POWER. PERSONNEL IN THE CAC SHOULD REMAIN
CLEAR OF THIS EXPOSED TERMINAL UNTIL POWER IS SWITCHED OFF OR
INJURY COULD RESULT.
(14) On the Fwd Aux Fuel Tank Overhead Panel push the R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-3 the multimeter attached to terminal stud 12 of FCD U1-710 (10)
reads less than 10 volts.
(b) On the FUEL synoptic page both Fwd Aux Right Pumps are shown as ON (amber circle
and pump vanes).
(c) After approximately 20 - 30 seconds the multimeter reads more than 110 volts.
NOTE: If the voltage does not increase to more than 110 volts and remain there, then
there is a possible wiring or component failure of the uncommanded on detection
circuitry and troubleshooting is necessary.
1) Monitor the voltage for an additional minute and verify that the voltage does not drop
back below 10 volts at any time.
(15) On the Fwd Aux Fuel Tank Overhead Panel push the R TRANS switch and verify as follows:
(a) At the CAC EPC Bay-3 the multimeter attached to terminal stud 12 of FCD U1-710 (10)
reads more than 110 volts.
(b) On the FUEL synoptic page both Fwd Aux Right Pumps are shown as OFF (white empty
circle).
WARNING: TAG AND USE SAFETY CLIPS TO SAFETY THE CIRCUIT BREAKERS. IF THE
CIRCUIT BREAKERS ARE NOT OPENED, TAGGED, AND SAFETIED, INJURY
TO PERSONS AND DAMAGE TO EQUIPMENT CAN OCCUR.
(16) Open circuit breaker as follows:
UPPER MAIN, FUEL AC BUS 3
NameNumberColumnRow
FUEL PUMP CONTROL AUX TANK 1 R FWDB1-164421G
APPENDIX A:  FUNCTIONAL TEST OF THE FUEL PUMPS UNCOMMANDED ON DETECTION CIRCUIT
(SHEET 25 OF 33)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 24, 2014
MD11-28-137
60 of 69
BOEING SERVICE BULLETIN MD11-28-137

The text continues at https://openairdocs.org/service-documents/boeing/md11-28-137/file/ff3641555398.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
