# Boeing Alert Service Bulletin MD80-55A067: No revision named - Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2011-0217; AD 2011-15-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. - Document: [Boeing Alert Service Bulletin MD80-55A067](https://openairdocs.org/service-documents/boeing/md80-55a067.md) - Title as filed: U.S. DOT/FAA - Service Bulletin - Pages: 55 - PDF: https://openairdocs.org/files/sha256/4c/f9/4cf9802e52991b102d3c83c415180ada9e57bc35402c64301c78efe9a1528199 - Page: https://openairdocs.org/service-documents/boeing/md80-55a067/file/4cf9802e5299 ## Text Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N. ### Page 1 Commercial Airplanes MD80 Service Bulletin ALERT Number: MD80-55A067 Original Issue: June 24, 2010 ATA System: 5531 SUBJECT: STABILIZERS - Vertical Stabilizer - Inspect/Repair Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15 CFR 730-774). An export license may be required before it is used for development, production or use by foreign persons from specific countries. The controller of this data has the individual responsibility to abide by all export laws. 9E991ECCN: BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET Copyright © 2010 The Boeing Company Unpublished Work - All Rights Reserved Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable subject matter. Boeing also claims copyright in this document as a compilation and/or collective work. This document includes proprietary information owned by The Boeing Company and/or one or more third parties. Treatment of the document and the information it contains is governed by contract with Boeing. For more information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124. Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner, BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document unless provided in writing by Boeing. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 1 of 55 2.0 ### Page 2 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 2 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT BLANK PAGE ### Page 3 Table of Contents Summary ...................................................... 5 1. PLANNING INFORMATION ........................................ 9 A. Effectivity ................................................ 9 1. Airplanes ............................................. 9 2. Spares Affected ........................................ 1 3 B. Concurrent Requirements ...................................... 1 3 C. Reason ................................................ 1 3 D. Description .............................................. 1 3 E. Compliance .............................................. 1 6 F. Approval ............................................... 2 5 G. Manpower .............................................. 2 5 H. Weight and Balance Changes .................................... 2 7 I. Electrical Load Data ......................................... 2 7 J. References .............................................. 2 7 1. Existing Data .......................................... 2 7 2. Data supplied with this Service Bulletin ............................ 2 7 3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 2 7 K. Publications Affected ........................................ 2 7 L. Interchangeability and Intermixability of Parts ........................... 2 8 2. MATERIAL INFORMATION ........................................ 2 9 A. Material - Price and Availability ................................... 2 9 B. Industry Support Information .................................... 2 9 C. Parts Necessary For Each Airplane ................................. 2 9 1. Kits/Parts ............................................ 2 9 2. Parts and Materials Supplied by the Operator ........................ 2 9 3. Parts Modified and Reidentified ................................ 2 9 4. Parts Removed and Not Replaced .............................. 2 9 D. Parts Necessary to Change Spares ................................. 2 9 E. Special Tooling - Price and Availability ............................... 2 9 F. Special Tooling Necessary to do this Service Bulletin ....................... 2 9 3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 1 A. GENERAL INFORMATION ..................................... 3 1 B. WORK INSTRUCTIONS ....................................... 3 2 APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION .......... 4 3 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 . 46 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 3 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 4 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 4 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT BLANK PAGE ### Page 5 Commercial Airplanes MD80 Service Bulletin ALERT SummaryNumber: MD80-55A067Original Issue: June 24, 2010 ATA System: 5531 SUBJECT: STABILIZERS - Vertical Stabilizer - Inspect/Repair Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO THE NEW OWNER. CONCURRENT REQUIREMENTS None. BACKGROUND Two operators reported finding a cracked vertical stabilizer skin at Station Zfs=52.267. Subsequent inspection revealed a severed front spar cap and a cracked front spar web. Cracks were also found on several other MD-80 airplanes, in the vertical stabilizer front spar cap bolt holes. The affected MD-80 airplanes had accrued between 39,749 through 56,212 flight-hours and 32,176 through 44,001 landing cycles when the cracks/anomalies were found. Boeing investigation determined that the skin cracks are due to high loading occurrences, such as, but not limited to, in-flight turbulence. Inspection will determine condition of the vertical stabilizer skin. Incorporation of the leading edge repair will minimize the possibility of crack growth. If not corrected, cracks in the vertical stabilizer leading edge and front spar cap may result in the structure unable to support limit load, and may lead to the loss of the vertical stabilizer. ACTION Refer to Paragraph 1.D., Description. EFFECTIVITY DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), MD-88 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes. COMPLIANCE Refer to Paragraph 1.E., Compliance. INDUSTRY SUPPORT INFORMATION Boeing warranty remedies are not available for the inspection and/or repair procedures given in this service bulletin. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 5 of 55 ### Page 6 MANPOWER Refer to Paragraph 1.G., Manpower. MATERIAL INFORMATION Operator Supplied Parts/Materials. Refer to Paragraph 2.A., Material - Price and Availability BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 6 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 7 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT INSPECT/REPAIR FIXED LEADING EDGE SKIN AND FRONT SPAR CAP AT STATION Zfs=52.267 000 1930929 Original Issue: June 24, 2010 MD80-55A067 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 7 of 55 ### Page 8 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 8 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT BLANK PAGE ### Page 9 Commercial Airplanes MD80 Service Bulletin ALERT Number: MD80-55A067 Original Issue: June 24, 2010 ATA System: 5531 SUBJECT: STABILIZERS - Vertical Stabilizer - Inspect/Repair Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 THIS BULLETIN IS SENT TO THE OPERATORS OF RECORD OF THE AIRPLANES SHOWN IN PARAGRAPH 1.A., EFFECTIVITY. IF AN AIRPLANE HAS BEEN LEASED OR SOLD, SEND THIS SERVICE BULLETIN TO THE NEW OPERATOR. IF APPLICABLE SPARES HAVE BEEN SOLD, SEND THIS SERVICE BULLETIN TO THE NEW OWNER. 1. PLANNING INFORMATION A. Effectivity 1. Airplanes This service bulletin is for the airplanes shown below. DESCRIPTIONCONFIGURATIONGROUP DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), MD-88 Airplanes -1 Airplane Models: DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), MD-88 GroupFuselage Num- ber 11000 - 1001 11004 - 1006 11008 - 1013 11016 11018 - 1019 11022 11025 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 9 of 55 ### Page 10 GroupFuselage Num- ber 11031 11034 - 1035 11043 11045 11049 11051 11053 11055 11057 11059 - 1060 11063 - 1080 11082 - 1083 11085 11087 - 1093 11095 - 1110 11112 - 1128 11130 - 1158 11160 - 1179 11181 11183 - 1223 11225 - 1241 11243 - 1273 11275 - 1290 11292 - 1323 11325 - 1334 11336 - 1350 11352 - 1451 11453 - 1477 11479 - 1503 11505 - 1666 11668 - 1701 11703 - 1771 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 10 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 11 GroupFuselage Num- ber 11773 - 1777 11779 - 1843 11845 - 1915 11917 - 1924 11926 - 1994 11996 - 2007 12009 - 2016 12019 - 2029 12031 - 2034 12036 - 2069 12071 - 2093 12101 - 2114 12116 12118 - 2119 12121 12124 12127 12130 12132 12134 - 2135 12137 12139 12145 12148 12151 - 2152 12167 12174 12176 12178 12180 12183 12185 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 11 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 12 GroupFuselage Num- ber 12187 12189 12192 12196 12199 12201 12204 12206 12208 12214 12218 12234 12239 12241 12244 12247 12249 12252 12254 12264 - 2287 1924 1938 1941 1944 1946 1948 1950 1952 - 953 1955 1957 - 958 1960 1962 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 12 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 13 GroupFuselage Num- ber 1965 - 967 1969 - 971 1973 - 975 1977 - 979 1981 1983 1986 1988 1991 - 992 1994 - 995 1997 1999 2. Spares Affected None. B. Concurrent Requirements None. C. Reason Two operators reported finding a cracked vertical stabilizer skin at Station Zfs=52.267. Subsequent inspection revealed a severed front spar cap and a cracked front spar web. Cracks were also found on several other MD-80 airplanes, in the vertical stabilizer front spar cap bolt holes. The affected MD-80 airplanes had accrued between 39,749 through 56,212 flight-hours and 32,176 through 44,001 landing cycles when the cracks/anomalies were found. Boeing investigation determined that the skin cracks are due to high loading occurrences, such as, but not limited to, in-flight turbulence. Inspection will determine condition of the vertical stabilizer skin. Incorporation of the leading edge repair will minimize the possibility of crack growth. If not corrected, cracks in the vertical stabilizer leading edge and front spar cap may result in the structure unable to support limit load, and may lead to the loss of the vertical stabilizer. D. Description This service bulletin provides instructions to do an initial inspection and repetitive inspections of the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267, and the vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins, as follows: NOTE: Refer to APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION, as a supplement to Paragraph 1.D., Description. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 13 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 14 PART A - INITIAL INSPECTION: 1. Removes two rows of fasteners above the splice and two rows of fasteners below the splice at Station Zfs=52.267. 2. Does a detailed inspection for "distress" in, and "existing repairs" to, the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267. NOTE: "Distress" is defined as deformed holes, elongated holes, oversized holes or cracks in the leading edge skin and splice. "Existing Repairs" are bushings, washers or reinforcing repairs to the leading edge. 3. Based on inspection results, does as follows: CONDITION 1 (Leading Edge is Not Distressed and No Existing Repair Found) a. Does an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267. b. Based on inspection results, does as follows: CONDITION 1A (No Crack Found) (1) Puts the airplane back to a serviceable condition. CONDITION 1B (Any Crack Found) (1) Does an evaluation/verification to confirm all crack indications. (2) Contacts Boeing for repair of all cracking and does the repair in accordance with Boeing's instructions. (3) Puts the airplane back to a serviceable condition. CONDITION 2 (Leading Edge is Distressed) a. Does an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267. b. Based on inspection results, does as follows: CONDITION 2A (No Crack Found) (1) Does leading edge repair. (2) Puts the airplane back to a serviceable condition. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 14 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 15 CONDITION 2B (Any Crack Found) (1) Does leading edge repair. (2) Does an evaluation/verification to confirm all crack indications. (3) Contacts Boeing for repair of all cracking and does the repair in accordance with Boeing's instructions. (4) Puts the airplane back to a serviceable condition. CONDITION 3 (Leading Edge Existing Repair Found) a. Does an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267. b. Based on inspection results, does as follows: CONDITION 3A (No Crack Found) (1) Puts the airplane back to a serviceable condition. CONDITION 3B (Any Crack Found) (1) Does an evaluation/verification to confirm all crack indications. (2) Contacts Boeing for repair of all cracking and does the repair in accordance with Boeing's instructions. (3) Puts the airplane back to a serviceable condition. PART B - REPETITIVE INSPECTION: 1. Inspection - Vertical Stabilizer Leading Edge: a. Does a detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners. b. Based on inspection results, does as follows: CONDITION 4 (No Loose Leading Edge Fasteners and No Missing Leading Edge Fasteners) (1) Does repetitive detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 15 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 16 CONDITION 5 (Loose Leading Edge Fasteners or Missing Leading Edge Fasteners) (1) Does leading edge repair. (2) Does repetitive detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners. 2. Inspection - Vertical Stabilizer Front Spar Cap Forward Flanges and either the Aft Flanges or Side Skins: a. Does an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267. b. Based on inspection results, does as follows: CONDITION 6 (No Crack Found) (1) Does repetitive inspection for cracks on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267. CONDITION 7 (Any Crack Found) (1) Does an evaluation/verification to confirm all crack indications. (2) Contacts Boeing for repair of all cracking and does the repair in accordance with Boeing's instructions. 3. Puts the airplane back to a serviceable condition. The work in this service bulletin is done in the maintenance zone(s) given below. Affected Maintenance Zones ZoneModel 63, 64DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC- 9-87 (MD-87), MD-88 E. Compliance The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin mandatory. NOTE: Refer to APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION, as a supplement to Paragraph 1.E., Compliance. NOTE: "Distress" is defined as deformed holes, elongated holes, oversized holes or cracks in the leading edge skin and splice. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 16 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 17 "Existing Repairs" are bushings, washers or reinforcing repairs to the leading edge. Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 4,500 flight cycles after the original issue date on this service bul- letin. Do a detailed inspection for "distress" in, and "existing repairs" to, the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. All Airplanes -Before further flight. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, using one of the options as follows: CONDITION 1 (Leading Edge is Not Distressed and No Ex- isting Repair Found) --OPTION 1: Do an open hole Eddy Current, High Fre- quency (ETHF) inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Paragraph 3.B., Work Instructions. AND Do a Radiographic Testing (RT) inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. OR --OPTION 2: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an ETHF surface inspection of the left and right side skins at the vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 17 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 18 Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -In Accordance With Table 2: PART B - Repetitive Inspec- tion: Fixed Leading Edge Skin at Sta- tion Zfs=52.267 Do repetitive inspections of the vertical stabi- lizer leading edge structure at the splice at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. CONDITION 1A (No Crack Found dur- ing either Option 1 or Option 2 Inspection) AND -In Accordance With Table 3: PART B - Repetitive Inspec- tion: Front Spar Cap at Station Zfs=52.267 Do repetitive inspections of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. -Before further flight. Do an evaluation/verification to confirm all crack indications in accordance with Para- graph 3.B., Work Instructions. CONDITION 1B (Any Crack Found dur- ing either Option 1 or Option 2 Inspection) -Before further flight. Contact Boeing for repair of all cracking and do the repair in accordance with Boeing's instructions. CONDITION 1B (Any confirmed crack indication) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 18 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 19 Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, using one of the options as follows: CONDITION 2 (Leading Edge is Dis- tressed) --OPTION 1: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. OR --OPTION 2: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an ETHF surface inspection of the left and right side skins at the vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. -Before further flight. Do leading edge repair in accordance with Paragraph 3.B., Work Instructions. CONDITION 2A (No Crack Found dur- ing either Option 1 or Option 2 Inspection) AND -In Accordance With Table 2: PART B - Repetitive Inspec- tion: Fixed Leading Edge Skin at Sta- tion Zfs=52.267 Do repetitive inspections of the vertical stabi- lizer leading edge structure at the splice at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. AND -In Accordance With Table 3: PART B - Repetitive Inspec- tion: Front Spar Cap at Station Zfs=52.267 Do repetitive inspections of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 19 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 20 Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight. Do leading edge repair in accordance with Paragraph 3.B., Work Instructions. CONDITION 2B (Any Crack Found dur- ing either Option 1 or Option 2 Inspection) AND -Before further flight. Do an evaluation/verification to confirm all crack indications in accordance with Para- graph 3.B., Work Instructions. AND -Before further flight. Contact Boeing for repair of all cracking and do the repair in accordance with Boeing's instructions. CONDITION 2B (Any confirmed crack indication) -Before further flight. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, using one of the options as follows: CONDITION 3 (Leading Edge Existing Repair Found) --OPTION 1: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. OR --OPTION 2: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an ETHF surface inspection of the left and right side skins at the vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 20 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 21 Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -In Accordance With Table 2: PART B - Repetitive Inspec- tion: Fixed Leading Edge Skin at Sta- tion Zfs=52.267 Do repetitive inspections of the vertical stabi- lizer leading edge structure at the splice at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. CONDITION 3A (No Crack Found dur- ing either Option 1 or Option 2 Inspection) AND -In Accordance With Table 3: PART B - Repetitive Inspec- tion: Front Spar Cap at Station Zfs=52.267 Do repetitive inspections of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. -Before further flight. Do an evaluation/verification to confirm all crack indications in accordance with Para- graph 3.B., Work Instructions. CONDITION 3B (Any Crack Found dur- ing either Option 1 or Option 2 Inspection) -Before further flight. Contact Boeing for repair of all cracking and do the repair in accordance with Boeing's instructions. CONDITION 3B (Any confirmed crack indication) Table 2: PART B - Repetitive Inspection: Fixed Leading Edge Skin at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 4,400 flight cycles after doing the initial inspec- tion. Do a detailed inspection of the vertical stabi- lizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accor- dance with Paragraph 3.B., Work Instruc- tions. Airplanes from CONDI- TION 1A or 2A or 3A of Table 1: PART A - Ini- tial Inspection on which the OPTION 1 inspec- tions were done. -Within 3,000 flight cycles after doing the initial inspec- tion. Do a detailed inspection of the vertical stabi- lizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accor- dance with Paragraph 3.B., Work Instruc- tions. Airplanes from CONDI- TION 1A or 2A or 3A of Table 1: PART A - Ini- tial Inspection on which the OPTION 2 inspec- tions were done. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 21 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 22 Table 2: PART B - Repetitive Inspection: Fixed Leading Edge Skin at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition 4,400 flight cycles (a) Within 4,400 flight cycles after doing the detailed inspec- tion. Do repetitive detailed inspection of the verti- cal stabilizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accordance with Paragraph 3.B., Work In- structions. CONDITION 4 (No Loose Leading Edge Fasteners and No Missing Leading Edge Fasteners) for airplanes on which the prior in- spection of the front spar cap was done us- ing OPTION 1. 3,000 flight cycles (a) Within 3,000 flight cycles after doing the detailed inspec- tion. Do repetitive detailed inspection of the verti- cal stabilizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accordance with Paragraph 3.B., Work In- structions. CONDITION 4 (No Loose Leading Edge Fasteners and No Missing Leading Edge Fasteners) for airplanes on which the prior in- spection of the front spar cap was done us- ing OPTION 2. -Before further flight. Do leading edge repair in accordance with Paragraph 3.B., Work Instructions. CONDITION 5 (Loose Leading Edge Fasteners or Missing Leading Edge Fasten- ers) for airplanes on which the prior inspec- tion of the front spar cap was done using OPTION 1. AND 4,400 flight cycles (a) Within 4,400 flight cycles after doing the detailed inspec- tion. Do repetitive detailed inspection of the verti- cal stabilizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accordance with Paragraph 3.B., Work In- structions. -Before further flight. Do leading edge repair in accordance with Paragraph 3.B., Work Instructions. CONDITION 5 (Loose Leading Edge Fasteners or Missing Leading Edge Fasten- ers) for airplanes on which the prior inspec- tion of the front spar cap was done using OPTION 2. AND 3,000 flight cycles (a) Within 3,000 flight cycles after doing the detailed inspec- tion. Do repetitive detailed inspection of the verti- cal stabilizer leading edge structure at the splice at Station Zfs=52.267 for indications of loose fasteners and missing fasteners in accordance with Paragraph 3.B., Work In- structions. (a) Changing from one inspection option to another option is acceptable, provided the repeat interval require- ment is first complied with, before changing options. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 22 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 23 Table 3: PART B - Repetitive Inspection: Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 4,400 flight cycles after doing the initial inspec- tion. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, using one of the options as follows: Airplanes from CONDI- TION 1A or 2A or 3A of Table 1: PART A - Ini- tial Inspection on which the OPTION 1 inspec- tions were done. --OPTION 1: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. OR --OPTION 2: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an ETHF surface inspection of the left and right side skins at the vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 23 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 24 Table 3: PART B - Repetitive Inspection: Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Within 3,000 flight cycles after doing the initial inspec- tion. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, using one of the options as follows: Airplanes from CONDI- TION 1A or 2A or 3A of Table 1: PART A - Ini- tial Inspection on which the OPTION 2 inspec- tions were done. --OPTION 1: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. OR --OPTION 2: Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges in accordance with Para- graph 3.B., Work Instructions. AND Do an ETHF surface inspection of the left and right side skins at the vertical stabilizer front spar cap aft flanges in accordance with Paragraph 3.B., Work Instructions. 4,400 flight cycles (a) Within 4,400 flight cycles after doing the inspection. Do repetitive inspections of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. CONDITION 6 (No Crack Found) for airplanes on which the prior inspection of the front spar cap was done using OPTION 1. 3,000 flight cycles (a) Within 3,000 flight cycles after doing the inspection. Do repetitive inspections of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with Paragraph 3.B., Work Instructions. CONDITION 6 (No Crack Found) for airplanes on which the prior inspection of the front spar cap was done using OPTION 2. -Before further flight. Do an evaluation/verification to confirm all crack indications in accordance with Para- graph 3.B., Work Instructions. CONDITION 7 (Any Crack Found dur- ing either Option 1 or Option 2 Inspection) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 24 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 25 Table 3: PART B - Repetitive Inspection: Front Spar Cap at Station Zfs=52.267 Repeat Interval (Not to Exceed) Compliance TimeActionCondition -Before further flight. Contact Boeing for repair of all cracking and do the repair in accordance with Boeing's instructions. CONDITION 7 (Any confirmed crack indication) (a) Changing from one inspection option to another option is acceptable, provided the repeat interval require- ment is first complied with, before changing options. F. Approval This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified in this service bulletin comply with the applicable regulations and are FAA approved, as well as European Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane in its original Boeing delivery configuration or as modified by other approved Boeing changes. If an airplane has a non-Boeing modification or repair that affects a component or system also affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval before incorporating this service bulletin. G. Manpower The table below shows an estimate of the task hours necessary to do the inspection/change/repair for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task hour data if necessary. The estimate does not include lost time. These are some examples of lost time:  Time to adjust to the workplace  Time to schedule the work  Time to inspect the work  Time to cure the materials  Time to make the parts  Time to find the tools. Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Elapsed HoursTask HoursNumber of PersonsTask 1.51.51Remove Fasteners - Fixed Leading Edge 1.01.01Inspect - Fixed Lead- ing Edge 1.01.01Remove Fasteners - Front Spar Cap For- ward Flange BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 25 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 26 Table 1: PART A - Initial Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Elapsed HoursTask HoursNumber of PersonsTask 1.01.01Inspect - Front Spar Cap Forward Flange 1.51.51Install Fasteners - Front Spar Cap For- ward Flange 2.02.01Inspect - Front Spar Cap Aft Flange 2.02.01Install Fasteners - Fixed Leading Edge 10.010.0TOTAL FOR EACH AIRPLANE (a) (b) (a) Inspection hours given are for each airplane. (b) Task hours required for repairs are not included and are to be determined by the operator based on inspection results. Table 2: PART B - Repetitive Inspection: Fixed Leading Edge Skin and Front Spar Cap at Station Zfs=52.267 Elapsed HoursTask HoursNumber of PersonsTask 1.01.01Inspect - Fixed Lead- ing Edge 1.01.01Remove Fasteners - Front Spar Cap For- ward Flange 1.01.01Inspect - Front Spar Cap Forward Flange 1.51.51Install Fasteners - Front Spar Cap For- ward Flange 2.02.01Inspect - Front Spar Cap Aft Flange 6.56.5TOTAL FOR EACH AIRPLANE (a) (b) (a) Inspection hours given are for each airplane. (b) Task hours required for repairs are not included and are to be determined by the operator based on inspection results. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 26 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 27 H. Weight and Balance Changes Weight and balance changes affected by incorporation of this service bulletin are contingent upon the changes to each particular airplane. Weight data is to be computed by the operator by weighing parts removed and parts installed during this change. Necessary revisions should be made to the appropriate airplane weight and balance report. I. Electrical Load Data Not changed. J. References 1. Existing Data a. Non-Destructive Test Standard Practices Manual (NDTSPM), 02-00-07, 06-00-07, 06-10-01.001, 06-10-01.003, Part 01-00-03, Part 02-00-03, Part 02-00-04, Part 06-00-03, Part 06-00-04. b. MD80 Structural Repair Manual (SRM) 55-03 Figure 29, Figure 30, and Figure 31, dated March 15, 2010. 2. Data supplied with this Service Bulletin None. 3. Installation Drawings Used in the Preparation of this Service Bulletin ChangeTitleDocument Number AREPAIR-FIXED LEADING EDGE SKIN, ZFS=52.267, VERTICAL STA- BILIZER SG09550004 DASTRUCTURE ASSY-VERT STAB5912123 YLEADING EDGE INSTL-VERTICAL STABILIZER 5930609 FCAP-VERT STAB FRONT SPAR5911394 ADSPAR ASSY-VERT STAB, FRONT9911833 These drawings were used to prepare this service bulletin. These drawings are not necessary to make the specified changes, and are not supplied with this service bulletin. These drawings may not be applicable to all airplane configurations or operators. K. Publications Affected 1. Publications: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 27 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 28 Chapter-SectionPublication MD80 SRM 55-03Structural Repair Manual 2. Damage Tolerance Based Structural Inspections: Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected are contained in Paragraph 1.E., Compliance of this service bulletin. L. Interchangeability and Intermixability of Parts Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 28 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 29 2. MATERIAL INFORMATION A. Material - Price and Availability None. B. Industry Support Information Boeing warranty remedies are not available for the inspection and/or repair procedures given in this service bulletin. C. Parts Necessary For Each Airplane 1. Kits/Parts Based on inspection results, refer to Figure 29 or Figure 30 or Figure 31 of MD80 SRM 55-03, dated March 15, 2010, for repair parts necessary for each airplane. 2. Parts and Materials Supplied by the Operator Based on inspection results, refer to Figure 29 or Figure 30 or Figure 31 of MD80 SRM 55-03, dated March 15, 2010, for operator supplied parts and materials necessary to do the required repairs. 3. Parts Modified and Reidentified None 4. Parts Removed and Not Replaced None D. Parts Necessary to Change Spares None E. Special Tooling - Price and Availability Inspection equipment required to accomplish this service bulletin are listed in APPENDIX B and in the NDTSPM and are to be procured from operator’s stock or sources indicated. F. Special Tooling Necessary to do this Service Bulletin No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine operator tool supply to make sure all necessary tools are available. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 29 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 30 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 30 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT BLANK PAGE ### Page 31 3. ACCOMPLISHMENT INSTRUCTIONS A. GENERAL INFORMATION WARNING: IF ELECTRICAL POWER IS APPLIED TO THE AIRPLANE, MAKE SURE YOU OBEY ALL PRECAUTIONS WHILE YOU DO WORK. IF YOU DO NOT OBEY THE PRECAUTIONS, DEATH OR INJURY TO PERSONS, AND DAMAGE TO THE AIRPLANE CAN OCCUR. CAUTION: ELECTRICALLY GROUND THE AIRPLANE. THIS WILL HELP TO PREVENT DAMAGE TO THE AIRPLANE OR EQUIPMENT. CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE. NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions, and the Figure(s) give the recommended sequence of steps. The sequence of steps to do this service bulletin can be changed. 2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for definition of the acronyms. 3. Equivalent parts are listed in the AEPL, Drawing 7595071. 4. Use the approved fastener substitutions and process material substitutions, in accordance with MD80 SRM 51. 5. Obey all of the warnings and cautions given in the specified manual sections. 6. The inspection area of the vertical stabilizer leading edge structure is two rows of fasteners above the splice and two rows of fasteners below the splice at Station Zfs=52.267. 7. "Distress" in the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267 is defined as deformed holes, elongated holes, oversized holes or cracks in the leading edge skin and splice. 8. "Existing Repairs" to the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267 are bushings, washers or reinforcing repairs to the leading edge. 9. "Breakaway torque" is defined as the torque required to overcome static friction when 100 percent of the locking feature is engaged and the fastener is unseated. Breakaway torque can be prefixed with a "maximum" or "minimum", and can be measured in either a loosening or tightening direction. Check for proper minimum breakaway torque. The minimum breakaway torque value for 1/4 inch diameter fasteners is 5.0 inch-pounds. The minimum breakaway torque value for 5/16 inch diameter fasteners is 7.0 inch-pounds. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 31 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 32 10. The inspection area of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins is defined as 12.50 inches +/- 0.25 inch above the leading edge skin splice and 12.50 inches +/- 0.25 inch below the leading edge skin splice at Station Zfs=52.267. 11. Where the work instructions include installation of a kept part, a new or serviceable part with the same part number can be installed as an alternative to the same part. The removed part can be discarded if a new part or serviceable part is installed. 12. Refer to APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION which describes the initial inspection and repetitive inspection requirements and can be used as a supplement to Paragraph 3.B., Work Instructions. 13. Refer to APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267, for the inspection procedures and requirements in accordance with Paragraph 3.B., Work Instructions. 14. A Detailed Inspection is defined as: An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required. 15. These work instructions refer to procedures included in other Boeing documents. When the words "refer to" are used and the operator has an accepted alternative procedure, the accepted alternative procedure can be used. When the words "in accordance with" are included in the instruction, the procedure in the Boeing document must be used. B. WORK INSTRUCTIONS PART A - INITIAL INSPECTION: 1. Do an initial inspection of the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267 as follows: a. Remove and keep two rows of fasteners above the splice and two rows of fasteners below the splice at Station Zfs=52.267. NOTE: Remove fasteners one row at a time. b. Do a detailed inspection for "distress" in, and "existing repairs" to, the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267. NOTE: "Distress" is defined as deformed holes, elongated holes, oversized holes or cracks in the leading edge skin and splice. "Existing Repairs" are bushings, washers or reinforcing repairs to the leading edge. 2. Based on inspection results, do as follows: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 32 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 33 CONDITION 1 (Leading Edge is Not Distressed and No Existing Repair Found) a. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with APPENDIX B, using one of the options as follows: NOTE: The inspection area is defined as 12.50 inches +/- 0.25 inch above the leading edge skin splice and 12.50 inches +/- 0.25 inch below the leading edge skin splice at Station Zfs=52.267. OPTION 1: (1) Do an Eddy Current, High Frequency (ETHF) inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do a Radiographic Testing (RT) inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 1. OPTION 2: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an ETHF surface inspection of the side skin at the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 2. b. Based on inspection results, do as follows: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 33 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 34 CONDITION 1A (No Crack Found during either Option 1 or Option 2 Inspection) (1) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. (2) Install kept leading edge fasteners. CONDITION 1B (Any Crack Found during either Option 1 or Option 2 Inspection) (1) Crack Found on the Vertical Stabilizer Front Spar Cap Forward Flange (a) Remove and keep nut plate gang channel on the vertical stabilizer front spar cap forward flange where the crack indication was found. (b) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer front spar cap forward flange. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept nut plate gang channel on the vertical stabilizer front spar cap forward flange. b) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap forward flange and do the repair in accordance with Boeing's instructions. (2) Crack Found on the Vertical Stabilizer Side Skin or Front Spar Cap Aft Flange (a) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer side skins. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer side skins and do the repair in accordance with Boeing's instructions. (b) Do an evaluation/verification to confirm any crack indication found on the front spar cap aft flange. Refer to NDTSPM 02-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 34 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 35 a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap aft flange and do the repair in accordance with Boeing's instructions. CONDITION 2 (Leading Edge is Distressed) a. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with APPENDIX B, using one of the options as follows: NOTE: The inspection area is defined as 12.50 inches +/- 0.25 inch above the leading edge skin splice and 12.50 inches +/- 0.25 inch below the leading edge skin splice at Station Zfs=52.267. OPTION 1: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 1. OPTION 2: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 35 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 36 (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an ETHF surface inspection of the side skin at the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 2. b. Based on inspection results, do as follows: CONDITION 2A (No Crack Found during either Option 1 or Option 2 Inspection) (1) Do leading edge repair in accordance with Figure 29 or Figure 30 or Figure 31 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. NOTE: At operator's discretion, replace 9911813-503 vertical stabilizer leading edge splice band or repair in accordance with Figure 29 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. (2) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. (3) Install kept leading edge fasteners. CONDITION 2B (Any Crack Found during either Option 1 or Option 2 Inspection) (1) Do leading edge repair in accordance with Figure 29 or Figure 30 or Figure 31 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. NOTE: At operator's discretion, replace 9911813-503 vertical stabilizer leading edge splice band or repair in accordance with Figure 29 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. (2) Crack Found on the Vertical Stabilizer Front Spar Cap Forward Flange (a) Remove and keep nut plate gang channel on the vertical stabilizer front spar cap forward flange where the crack indication was found. (b) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer front spar cap forward flange. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 36 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 37 a) Install kept nut plate gang channel on the vertical stabilizer front spar cap forward flange. b) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap forward flange and do the repair in accordance with Boeing's instructions. (3) Crack Found on the Vertical Stabilizer Side Skin or Front Spar Cap Aft Flange (a) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer side skins. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer side skins and do the repair in accordance with Boeing's instructions. (b) Do an evaluation/verification to confirm any crack indication found on the front spar cap aft flange. Refer to NDTSPM 02-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap aft flange and do the repair in accordance with Boeing's instructions. CONDITION 3 (Leading Edge Existing Repair Found) a. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with APPENDIX B, using one of the options as follows: NOTE: The inspection area is defined as 12.50 inches +/- 0.25 inch above the leading edge skin splice and 12.50 inches +/- 0.25 inch below the leading edge skin splice at Station Zfs=52.267. OPTION 1: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 37 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 38 (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 1. OPTION 2: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an ETHF surface inspection of the side skin at the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 2. b. Based on inspection results, do as follows: CONDITION 3A (No Crack Found during either Option 1 or Option 2 Inspection) (1) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. (2) Install kept leading edge fasteners. CONDITION 3B (Any Crack Found during either Option 1 or Option 2 Inspection) (1) Crack Found on the Vertical Stabilizer Front Spar Cap Forward Flange (a) Remove and keep nut plate gang channel on the vertical stabilizer front spar cap forward flange where the crack indication was found. (b) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer front spar cap forward flange. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 38 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 39 a) Install kept nut plate gang channel on the vertical stabilizer front spar cap forward flange. b) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap forward flange and do the repair in accordance with Boeing's instructions. (2) Crack Found on the Vertical Stabilizer Side Skin or Front Spar Cap Aft Flange (a) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer side skins. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer side skins and do the repair in accordance with Boeing's instructions. (b) Do an evaluation/verification to confirm any crack indication found on the front spar cap aft flange. Refer to NDTSPM 02-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap aft flange and do the repair in accordance with Boeing's instructions. 3. Put the airplane back to a serviceable condition. 4. Do repetitive inspections of the vertical stabilizer leading edge structure at the splice at Station Zfs=52.267, and the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267, at intervals specified in Paragraph 1.E., Compliance. PART B - REPETITIVE INSPECTION: 1. Inspection - Vertical Stabilizer Leading Edge: a. Do a detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 39 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 40 NOTE: The inspection area is two rows of fasteners above the splice and two rows of fasteners below the splice at Station Zfs=52.267. b. Based on inspection results, do as follows: CONDITION 4 (No Loose Leading Edge Fasteners and No Missing Leading Edge Fasteners) (1) Do repetitive detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners at intervals specified in Paragraph 1.E., Compliance. CONDITION 5 (Loose Leading Edge Fasteners or Missing Leading Edge Fasteners) (1) Do leading edge repair in accordance with Figure 29 or Figure 30 or Figure 31 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. NOTE: At operator's discretion, replace 9911813-503 vertical stabilizer leading edge splice band or repair in accordance with Figure 29 of MD80 SRM 55-03, dated March 15, 2010, or Service General Repair Drawing SG09550004, as applicable. (2) Do repetitive detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners at intervals specified in Paragraph 1.E., Compliance. 2. Inspection - Vertical Stabilizer Front Spar Cap Forward Flanges and either the Aft Flanges or Side Skins: a. Do an inspection for cracking on the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 in accordance with APPENDIX B, using one of the options as follows: NOTE: The inspection area is defined as 12.50 inches +/- 0.25 inch above the leading edge skin splice and 12.50 inches +/- 0.25 inch below the leading edge skin splice at Station Zfs=52.267. OPTION 1: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 40 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 41 (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an RT inspection of the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 1. OPTION 2: (1) Do an ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges as follows: (a) Remove and keep fasteners common to the left and right vertical stabilizer front spar cap forward flanges, above and below the leading edge skin splice at Station Zfs=52.267. (b) Do an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges at the fastener holes above and below the leading edge skin splice at Station Zfs=52.267 in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 1. (2) Do an ETHF surface inspection of the side skin at the left and right vertical stabilizer front spar cap aft flanges in accordance with the inspection procedure in APPENDIX B, Inspection Sequence 2 - Option 2. b. Based on inspection results, do as follows: CONDITION 6 (No Crack Found during either Option 1 or Option 2 Inspection) (1) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. (2) Install kept leading edge fasteners. CONDITION 7 (Any Crack Found during either Option 1 or Option 2 Inspection) (1) Crack Found on the Vertical Stabilizer Front Spar Cap Forward Flange (a) Remove and keep nut plate gang channel on the vertical stabilizer front spar cap forward flange where the crack indication was found. (b) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer front spar cap forward flange. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 41 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 42 a) Install kept nut plate gang channel on the vertical stabilizer front spar cap forward flange. b) Install kept fasteners common to the left and right vertical stabilizer front spar cap forward flanges. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap forward flange and do the repair in accordance with Boeing's instructions. (2) Crack Found on the Vertical Stabilizer Side Skin or Front Spar Cap Aft Flange (a) Do an evaluation/verification to confirm any crack indication found on the vertical stabilizer side skins. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer side skins and do the repair in accordance with Boeing's instructions. (b) Do an evaluation/verification to confirm any crack indication found on the front spar cap aft flange. Refer to NDTSPM 02-00-07 for applicable Crack/Defect Evaluation/Verification. 1) Crack Indication Not Confirmed a) Install kept leading edge fasteners. 2) Crack Indication Confirmed a) Contact Boeing for repair of the vertical stabilizer front spar cap aft flange and do the repair in accordance with Boeing's instructions. 3. Put the airplane back to a serviceable condition. 4. Do repetitive detailed inspection of the vertical stabilizer leading edge at the splice at Station Zfs=52.267 (fasteners not removed) for indications of loose fasteners and missing fasteners at intervals specified in Paragraph 1.E., Compliance. 5. Do repetitive inspection of the left and right vertical stabilizer front spar cap forward flanges and either the aft flanges or side skins at Station Zfs=52.267 at intervals specified in Paragraph 1.E., Compliance. BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 42 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 43 APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION 1. This flowchart describes the initial inspection and repetitive inspection requirements and can be used as a supplement to Paragraph 1.D., Description, Paragraph 1.E., Compliance, and Paragraph 3.B., Work Instructions. APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION (SHEET 1 OF 3) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 43 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 44 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT PART A INITIAL INSPECTION TABLE 1 TABLE 1 REMOVE TWO FASTENER ROWS ABOVE INSPECT VS FRONT AND BELOW SPLICE AT Zis = 52.267 LE DISTRESSED CONDITION 2 SPAR CAP FWD AND AFT FLANGE OR VS FRONT CRACK FOUND > CONDITION 2B YES REPAIR LE SPAR CAP FWD FLANGE AND SIDE SKIN INSPECT NO FOR "DISTRESS" IN CONDITION 2A AND EXISTING CONTACT BOEING REPAIRS TO VS FOR REPAIR OF LE STRUCTURE ALL CRACKING YES REPAIR LE DISTRESS OR REPAIRED PUT AIRPLANE BACK TO NO SERVICEABLE CONDITION 1 YES CONDITION INSPECT VS FRONT INSPECT VS FRONT SPAR CAP FWD AND AFT FLANGE OR VS FRONT CONDITION 3 SPAR CAP FWD AND AFT FLANGE OR VS FRONT CRACK FOUND CONDITION 3B YES CONTACT BOEING FOR REPAIR OF ALL CRACKING SPAR CAP FWD FLANGE SPAR CAP FWD FLANGE AND SIDE SKIN AND SIDE SKIN NO CONDITION 3A CRACK CONTACT BOEING FOUND YES FOR REPAIR OF CONDITION 1B ALL CRACKING PUT AIRPLANE BACK TO NO SERVICEABLE CONDITION 1A CONDITION PUT AIRPLANE BACK TO SERVICEABLE CONDITION CONTINUE TO PART B REPETITIVE INSPECTION APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION (SHEET 2 OF 3) Original Issue: June 24, 2010 BOEING PROPRIETARY - MD80-55A067 Copyright Unpublished Work - See page 1 for details. 44 of 55 ### Page 45 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT PART B REPETITIVE INSPECTIONS TABLE 2 AND 3 TABLE 2 TABLE 3 INSPECT LE FOR INSPECT VS FRONT LOOSE AND REPEAT SPAR CAP BASED ON MISSING FASTENERS INSPECTION ACCOMPLISHMENT OF OPTION 1 OR OPTION 2 FASTENERS LOOSE OR YES REPAIR LE MISSING CONDITION 5 OPTION 1 OPTION 2 INSPECT VS INSPECT VS FRONT SPAR CAP FRONT SPAR CAF FWD AND AFT FWD FLANGE AND FLANGE SIDE SKIN NO CONDITION 4 CONTACT BOEING CRACK FOUND FOR REPAIR OF ALL CONDITION 7 CRACKING NO CONDITION 6 PUT AIRPLANE REPEAT SERVICEABLE INSPECTION CONDITION 1986957 APPENDIX A: FLOWCHART - INITIAL INSPECTION AND REPETITIVE INSPECTION (SHEET 3 OF 3) Original Issue: June 24, 2010 BOEING PROPRIETARY - MD80-55A067 Copyright © Unpublished Work - See page 1 for details. 45 of 55 ### Page 46 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 1. Model Affected: MD-80 2. Drawing Reference: 5912123, 5930609, 5911394, 9911833 Description: 1. The inspection area consists of the vertical stabilizer front spar caps at Station Zfs=52.267. The purpose of Inspection Sequence 1 is to inspect the fastener holes common to the left and right front spar cap forward flanges and leading edge panels in accordance with Figure 1. The purpose of Inspection Sequence 2 is to detect fatigue cracks initiating at the fastener holes common to the left and right spar cap aft flanges and/or side skins in accordance with Figure 2 or Figure 3. The fatigue cracks will travel in the forward and aft directions from the fastener holes. NOTE: Two inspection methods are acceptable for Inspection Sequence 2 as follows: Option 1 - Radiographic Testing (RT) Option 2 - Eddy Current, High Frequency (ETHF) Inspection Sequence 1: 1. Eddy Current, High Frequency (ETHF) Inspection Sequence 2: 1. Radiographic Testing (RT) or Eddy Current, High Frequency (ETHF) Preparation for Inspection 1. Remove all dirt, grease, and loose paint from the inspection area. 2. Thoroughly clean the inspection area with an approved cleaning agent. Table 1 - Equipment/Materials SupplierCAGEQTYTypeTest Equipment Staveley Instruments0M4211Sperry SPX 160Portable X-ray machine (1.5 mm projected focal spot). 1329 East Kemper Road Cincinnati, Ohio 45246 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 1 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 46 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 47 Table 1 - Equipment/Materials SupplierCAGEQTYTypeTest Equipment Eastman Kodak Company1913910Kodak MX-ray film 343 State Street(Refer to Table 2 for sizes) Rochester, New York 14650 191394Kodak AAX-ray film (Refer to Table 2 for sizes) Source Optional--For radiographic identifica- tion. Lead numbers Source Optional---Masking Tape Source Optional-In conformance with envi- ronmental regulations and harmless to surfaces con- tacted. Cleaning Agent NOTE: The equipment/materials listed above were used to develop this procedure. Refer to NDTSPM Part 02-00-04 and NDTSPM Part 06-00-04 for supplier/vendor information. 1. 2. Equipment/material substitutions producing results equivalent to those defined by this document may also be used. Refer to NDTSPM Part 01-00-03, NDTSPM Part 02-00-03, and NDTSPM Part 06-00-03 for equipment/material information. Inspection Procedure: 1. Inspection Sequence 1 (Front Spar Cap Forward Flange Area) Inspection Method 01 (Eddy Current, High Frequency) a. Perform an open hole ETHF inspection of the left and right vertical stabilizer front spar cap forward flanges above and below the leading edge skin splice at Station Zfs=52.267 within the specified dimensions in accordance with Figure 1. Scan the circumference of the holes following the instructions found in the Nondestructive Testing Standard Practice Manual NDTSPM 06-10-01.003 (ETHF - Procedure 3). NOTE: Scoring of the fastener hole bore caused by the removal of fasteners may cause crack-like indications. Removal of nut plate may be necessary for proper clean up of the hole. Refer to NDTSPM 06-10-01.003 "Access" and "Preparation and Cleaning" for further information. The nut plate may also interfere with the probe scan with some open hole eddy current probe designs. APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 2 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 47 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 48 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT VERTICAL STABILIZER LEADING EDGE -RONT SPAR CAP PANEL 12.5‡0.25 ++++++ SIDE SKIN CRACK (TYPICAL) Zfs = 52.267 OPEN HOLE EDDY CURRENT INSPECT THE SPAR CAP WITHIN THE SPECIFIED DIMENSION (12.50 INCHES ‡0.25 ABOVE AND 12.5‡0.25 BELOW STATION Zfs = 52.267) TTY DORSAL FIN - LOWER ASSEMBLY A-A LEFT SIDE SHOWN (RIGHT SIDE OPPOSITE) VIEW LOOKING INBOARD FROM OUTSIDE VERTICAL STABILIZER HIGH FREQUENCY EDDY CURRENT INSPECTION OF SPAR CAP FORWARD FLANGE AT STATION Zfs = 52.267 FIGURE 1 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 3 OF 10) Original Issue: June 24, 2010 MD80-55A067 BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. 48 of 55 ### Page 49 2. Inspection Sequence 2 (Front Spar Cap Aft Flange Area) OPTION 1: Inspection Method 01 (Radiographic Testing) a. Inspection for cracks of the vertical stabilizer front spar cap aft flange at Station Zfs=52.267 in accordance with Figure 2. NOTE: The following steps must be done to both left and right sides of the vertical stabilizer. EXPOSURE 1: (1) Prepare Exposure 1 radiographic identification tag with the data as follows, using operator's shop practice: – Service Bulletin number – Exposure number and left or right side – Aircraft I.D. – Date (2) Attach Exposure 1 identification tag to film pack for each exposure using operator's shop practice. (3) Use masking tape to attach film to inspection element for Exposure 1 in accordance with Figure 2. (4) Expose film in accordance with x-ray parameters in Table 2 and Figure 2. EXPOSURE 2: (1) Prepare Exposure 2 radiographic identification tag with the data as follows, using operator's shop practice: – Service Bulletin number – Exposure number and left or right side – Aircraft I.D. – Date (2) Attach Exposure 2 identification tag to film pack for each exposure using operator's shop practice. (3) Use masking tape to attach film to inspection element for Exposure 2 in accordance with Figure 2. (4) Expose film in accordance with x-ray parameters in Table 2 and Figure 2. EXPOSURE 3: (1) Prepare Exposure 3 radiographic identification tag with the data as follows, using operator's shop practice: APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 4 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 49 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 50 – Service Bulletin number – Exposure number and left or right side – Aircraft I.D. – Date (2) Attach Exposure 3 identification tag to film pack for each exposure using operator's shop practice. (3) Use masking tape to attach film to inspection element for Exposure 3 in accordance with Figure 2. (4) Expose film in accordance with x-ray parameters in Table 2 and Figure 2. EXPOSURE 4: (1) Prepare Exposure 4 radiographic identification tag with the data as follows, using operator's shop practice: – Service Bulletin number – Exposure number and left or right side – Aircraft I.D. – Date (2) Attach Exposure 4 identification tag to film pack for each exposure using operator's shop practice. (3) Use masking tape to attach film to inspection element for Exposure 4 in accordance with Figure 2. (4) Expose film in accordance with x-ray parameters in Table 2 and Figure 2. EXPOSURE 5: (1) Prepare Exposure 5 radiographic identification tag with the data as follows, using operator's shop practice: – Service Bulletin number – Exposure number and left or right side – Aircraft I.D. – Date (2) Attach Exposure 5 identification tag to film pack for each exposure using operator's shop practice. (3) Use masking tape to attach film to inspection element for Exposure 5 in accordance with Figure 2. (4) Expose film in accordance with x-ray parameters in Table 2 and Figure 2. APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 5 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 50 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 51 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT VERTICAL STABILIZER LEADING EDGE FRONT SPAR CAP PANEL 3 TO 4 INCHES * OVERLAP FILM PLACEMENT SIDE SKIN 1.5 INCHES ‡0.25 (4 PLACES) - FILM PLACEMENT EXPOSURE 1 (SHOWN 10.010.25 TRANSPARENT † 12.5‡0.25 + FILM PLACEMENT EXPOSURE 2 (SHOWN 5.0‡0.25 TRANSPARENT) FILM PLACEMENT EXPOSURE 3 (SHOWN 5.010.25 TRANSPARENT) Zfs = 52.267 FILM PLACEMENT EXPOSURE 4 12.5t0.25 10.010.25 TRANSPARENT) (SHOWN FILM PLACEMENT EXPOSURE 5 SHOWN TRANSPARENT) INDICATES THE TARGET LOCATION OF DORSAL FIN THE X-RAY TUBE HEAD PORT AT THE LOWER ASSEMBLY OPPOSITE SIDE OF THE VERTICAL STABILIZER TO THE CENTER OF THE AREA BEING INSPECTED A-A * LEFT SIDE SHOWN (RIGHT SIDE OPPOSITE) VIEW LOOKING INBOARD FROM OUTSIDE VERTICAL STABILIZER TARGET SHOULD BE AFT OF AFT FLANGE AND SLIGHTLY OBLIQUE, SO THE FIRST FLANGE IS NOT SUPERIMPOSED OVER THE FLANGE BEING INSPECTED RADIOGRAPHIC TESTING AT AFT FLANGE AT STATION Zfs = 52.267 1930944 FIGURE 2 (SHEET 1) APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 6 OF 10) Original Issue: June 24, 2010 BOEING PROPRIETARY - MD80-55A067 Copyright © Unpublished Work - See page 1 for details. 51 of 55 ### Page 52 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT FILM PLACEMENT (TYPICAL) \ DIM "A" - (REFER TO TABLE 2) 18.7 ‡ 0.5- B-B VIEW LOOKING AFT RADIOGRAPHIC TESTING AT AFT FLANGE AT STATION Zfs = 52.267 FIGURE 2 (SHEET 2) 1984207 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS-52.267 (SHEET 7 OF 10) Original Issue: June 24, 2010 BOEING PROPRIETARY - MD80-55A067 Copyright © Unpublished Work - See page 1 for details. 52 of 55 ### Page 53 Table 2: Radiographic Exposure Data for Vertical Stabilizer Front Spar Cap Aft Flange at Station Zfs=52.267 REMARKSFILMDIM "A" (Inch) mas (a) kVEXPOSURE NUMBER SIZE (Inch) QTYASTM TYPE 5 X 721 (b)36 +/- 0.5600801 5 X 721 and 2 (c)36 +/- 0.5600802 5 X 721 and 2 (c)36 +/- 0.5600803 5 X 721 (b)36 +/- 0.5600804 5 X 721 (b)36 +/- 0.5600805 (a) May adjust mas as necessary to achieve a 1.7 to 3.5 H & D Density in the area of interest. (b) Kodak M or equivalent type with similar speed. (c) Kodak M and AA or equivalent type with similar speed (double load film pack). OPTION 2: Inspection Method 01 (Eddy Current, High Frequency) a. Perform an ETHF surface inspection of the vertical stabilizer side skins at those fasteners common to the left and right vertical stabilizer front spar cap aft flanges within the specified dimensions in accordance with Figure 3. Scan around the fasteners looking for cracks in the forward and aft direction. Scan around fasteners following the instructions found in the Nondestructive Testing Standard Practice Manual NDTSPM 06-10-01.001 (ETHF - Procedure 1). Use Calibration Method "P" and Scan Method "47". APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 8 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 53 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT ### Page 54 (OCR) BOEING SERVICE BULLETIN MD80-55A067 ALERT ALERT VERTICAL STABILIZER LEADING EDGE FRONT SPAR CAP PANEL •SIDE SKIN 12.5‡0.25 CRACK (TYPICAL) Zfs = 52.267 EDDY CURRENT INSPECT THE 12.5t0.25 SIDE SKIN WITHIN THE SPECIFIED DIMENSION (12.50 INCHES ‡0.25 ABOVE AND BELOW STATION Zfs = 52.267) DORSAL FIN - LOWER ASSEMBLY A-A LEFT SIDE SHOWN (RIGHT SIDE OPPOSITE) VIEW LOOKING INBOARD FROM OUTSIDE VERTICAL STABILIZER HIGH FREQUENCY EDDY CURRENT INSPECTION OF SIDE SKIN AT AFT FLANGE AT STATION Zfs = 52.267 FIGURE 3 1931422 APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS-52.267 (SHEET 9 OF 10) Original Issue: June 24, 2010 MD80-55A067 Copyright © Unpublished Work - See page 1 for details. BOEING PROPRIETARY - 54 of 55 ### Page 55 Inspection Results 1. Any indication is considered a crack which exhibits the same relative phase angle and an amplitude of 50 percent or greater than the indication obtained from the calibration notch in the reference standard. 2. Crack indications found during ETHF inspection shall be confirmed. Refer to NDTSPM 06-00-07 for applicable Crack/Defect Evaluation/Verification sections(s). 3. Crack indications found during RT inspection shall be confirmed. Refer to NDTSPM 02-00-07 for applicable Crack/Defect Evaluation/Verification section(s). Post Inspection Procedure 1. Remove and secure all test equipment and materials from the area. APPENDIX B: INSPECTION OF VERTICAL STABILIZER FRONT SPAR CAP AT STATION ZFS=52.267 (SHEET 10 OF 10) BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details. Original Issue: June 24, 2010 MD80-55A067 55 of 55 BOEING SERVICE BULLETIN MD80-55A067 ALERTALERT --- OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.