# Boeing Special Attention Service Bulletin 727-53-0232: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0646; AD 2011-01-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 727-53-0232](https://openairdocs.org/service-documents/boeing/sb-727-53-0232.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 111
- PDF: https://openairdocs.org/files/sha256/f0/5e/f05e6568320d11c0816b87583b3fe43685adccadd57cab2fc1d6151152a602e3
- Page: https://openairdocs.org/service-documents/boeing/sb-727-53-0232/file/f05e6568320d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
Number: 727-53-0232
Original Issue: September 23, 2009
ATA System: 5311
SUBJECT: FUSELAGE - Frames and Bulkheads - Body Station (STA) 1183 - Aft Pressure Bulkhead
Web Inspection, Repair and Preventive Modification.
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2009 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
1 of 111
5.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
2 of 111
BOEING SERVICE BULLETIN 727-53-0232
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 5
B. Concurrent Requirements ...................................... 1 5
C. Reason ................................................ 1 5
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 1 8
G. Manpower .............................................. 1 9
H. Weight and Balance Changes .................................... 2 1
I. Electrical Load Data ......................................... 2 1
J. References .............................................. 2 1
1. Existing Data .......................................... 2 1
2. Data supplied with this Service Bulletin ............................ 2 2
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 2 2
K. Publications Affected ........................................ 2 2
L. Interchangeability and Intermixability of Parts ........................... 2 2
2. MATERIAL INFORMATION ........................................ 2 3
A. Material - Price and Availability ................................... 2 3
B. Industry Support Information .................................... 2 3
C. Parts Necessary For Each Airplane ................................. 2 3
1. Kits/Parts ............................................ 2 3
2. Parts and Materials Supplied by the Operator ........................ 2 3
3. Parts Modified and Reidentified ................................ 2 4
4. Parts Removed and Not Replaced .............................. 2 4
D. Parts Necessary to Change Spares ................................. 2 4
E. Special Tooling - Price and Availability ............................... 2 5
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 5
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 7
A. GENERAL INFORMATION ..................................... 2 7
B. WORK INSTRUCTIONS ....................................... 2 7
FIGURE 1: INSPECTION OF THE AREA AROUND THE HYDRAULIC LINE SUPPORT BRACKET [Group
1, Configuration 1; Group 2] .................................. 3 1
FIGURE 2: INSPECTION OF THE AREA WITHOUT THE HYDRAULIC LINE SUPPORT BRACKET [Group
1, Configuration 2] ....................................... 3 4
FIGURE 3: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE UPPER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET [Group 1, Configuration 1; Group
2 ]  ................................................ 3 7
FIGURE 4: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE LOWER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET [Group 1, Configuration 1; Group
2 ]  ................................................ 4 0
FIGURE 5: TRIM OUT CRACKS LESS THAN OR EQUAL TO 10 INCHES LONG AT THE HYDRAULIC
LINE SUPPORT BRACKET LOCATION [Group 1, Configuration 1; Group 2] ....... 4 3
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
3 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 4

FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
[Group 1, Configuration 1; Group 2] .............................. 4 6
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT [Group 1,
Configuration 1; Group 2] ................................... 5 3
FIGURE 8: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR LOWER 4 INCH CRACK CUTOUT
[Group 1, Configuration 1; Group 2] .............................. 5 9
FIGURE 9: TYPICAL REPAIR INSTALLATION FOR LOWER 4 INCH CRACK CUTOUT [Group 1,
Configuration 1; Group 2] ................................... 6 6
FIGURE 10: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR 10 INCH CRACK CUTOUT [Group 1,
Configuration 1; Group 2] ................................... 7 2
FIGURE 11: TYPICAL REPAIR INSTALLATION FOR 10 INCH CRACK CUTOUT [Group 1, Configuration
1; Group 2] ........................................... 7 9
FIGURE 12: PREPARATION FOR INSTALLATION OF PREVENTIVE MODIFICATION DOUBLER [Group
1, Configuration 1; Group 2] .................................. 8 5
FIGURE 13: INSTALLATION OF PREVENTIVE MODIFICATION DOUBLER [Group 1, Configuration 1; Group
2 ]  ................................................ 9 1
FIGURE 14: BULKHEAD WEB INSPECTION WITH UPPER 4 INCH CUTOUT REPAIR DOUBLER
INSTALLED [Group 1, Configuration 1; Group 2] ....................... 9 6
FIGURE 15: BULKHEAD WEB INSPECTION WITH LOWER 4 INCH CUTOUT REPAIR DOUBLER
INSTALLED [Group 1, Configuration 1; Group 2] ...................... 1 0 0
FIGURE 16: BULKHEAD WEB INSPECTION WITH 10 INCH CUTOUT REPAIR DOUBLER INSTALLED
[Group 1, Configuration 1; Group 2] ............................. 1 0 4
FIGURE 17: BULKHEAD WEB INSPECTION WITH PREVENTIVE MODIFICATION DOUBLER INSTALLED
[Group 1, Configuration 1; Group 2] ............................. 1 0 8
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
4 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 5

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 727-53-0232Original Issue: September 23, 2009
ATA System: 5311
SUBJECT: FUSELAGE - Frames and Bulkheads - Body Station (STA) 1183 - Aft Pressure Bulkhead
Web Inspection, Repair and Preventive Modification.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will detect cracks if present in the aft pressure bulkhead web. A cracked
aft pressure bulkhead web may result in difficulty in achieving or maintaining cabin pressurization, or result in
rapid decompression.
Boeing received 13 reports of cracks in the aft pressure bulkhead web ranging from 0.75 inches to 11.8 inches
in length at Left Buttock Line (LBL) 61, between Water Line (WL) 220 and WL 228. The cracks originated at the
hydraulic line support brackets which were installed in production after airplane Line Number 1336, or in
accordance with Service Bulletin 727-29-0057. The cracks were found on airplanes which had accumulated
flight hours ranging from 14,939 to 39,369 and flight cycles ranging from 10,685 to 29,357. The cracks are
attributed to fatigue of the aft pressure bulkhead web due to vibrations from the number 1 engine hydraulic pump
line in addition to normal pressurization cycles. Material analysis revealed multiple crack initiation sites and no
evidence of corrosion.
This service bulletin gives instructions for initial and repeat inspections of the aft pressure bulkhead web for any
crack and to install a preventive modification if no crack is found or to install a repair if any crack is found.
Accomplishment of this service bulletin will make sure that cracks in the aft pressure bulkhead web are prevented
or detected and repaired before the structural integrity of the aft pressure bulkhead is degraded.
Boeing Service Related Problem 727-SRP-53-0314 is related to this service bulletin.
ACTION
Group 1, Configuration 1; Group 2:
Get access to the aft pressure bulkhead web. Do a detailed inspection for any crack in the aft pressure bulkhead
web around the hydraulic line support bracket area. If no crack is found, either repeat the inspection in accordance
with Paragraph 1.E., Compliance or accomplish the preventive modification in accordance with this service
bulletin. If any crack is found, accomplish the repair in accordance with this service bulletin. If any crack is found
to exceed the trim out limits given in this service bulletin contact Boeing for repair instructions and do the repair.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
5 of 111

### Page 6

Group 1, Configuration 2:
Get access to the aft pressure bulkhead web. Do a detailed inspection for any crack in the aft pressure bulkhead
web between WL 217 and WL 230, and LBL 48 and LBL 66. If no crack is found, repeat the detailed inspection
at intervals given in Paragraph 1.E., Compliance. If any crack is found, contact Boeing for repair instructions
and do the repair.
EFFECTIVITY
All 727 Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Federal Aviation Administration Airworthiness Directive FAA AD 98-11-03 R1 is related to this service bulletin.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, repair and/or preventive modification procedures
given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials. Refer to Paragraph 2.C.2., Parts and Materials Supplied by the Operator.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
6 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 7 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
STA
1183  AFT PRESSURE
BULKHEAD WEB
INSPECT THE AREA AROUND
THE HYDRAULIC LINE SUPPORT
BRACKET FOR ANY CRACK. IF
ANY CRACK IS FOUND
ACCOMPLISH THE REPAIR. IF
NO CRACK IS FOUND
ACCOMPLISH THE PREVENTIVE
MODIFICATION.  1548918
STA 1183 AFT PRESSURE BULKHEAD
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  7 0t 111

### Page 8

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
8 of 111
BOEING SERVICE BULLETIN 727-53-0232
BLANK PAGE

### Page 9

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
Number: 727-53-0232
Original Issue: September 23, 2009
ATA System: 5311
SUBJECT: FUSELAGE - Frames and Bulkheads - Body Station (STA) 1183 - Aft Pressure Bulkhead
Web Inspection, Repair and Preventive Modification.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-9825 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
727 Airplanes Line Number 1-1336 that did not have the 65-17944-84
support bracket installed in production.
-1
Airplanes that have incorporated Service Bulletin 727-29-0057.1
Airplanes that have not incorporated Service Bulletin 727-29-0057.2
727 Airplanes Line Number 1337-1832 that had the 65-17944-84
support bracket installed in production.
-2
Airplane Models:
727, 727-100, 727-100C, 727-200, 727-200F, 727C
GroupVariable Number
1E0001 - E0042
1E0101 - E0140
1E0201 - E0216
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
9 of 111

### Page 10

GroupVariable Number
1E0301 - E0351
1E0401 - E0423
1E3001 - E3006
1E3011 - E3014
1E3021 - E3040
1E3059
1E3061 - E3077
1E3101 - E3103
1E3111 - E3118
1E3141 - E3152
1E3171 - E3177
1E3201 - E3206
1E3221 - E3224
1E3241 - E3290
1E3341 - E3350
1E3401 - E3421
1E3451 - E3452
1E3471 - E3474
1E3501 - E3513
1E3516 - E3523
1E3551 - E3553
1E3571 - E3578
1E3601 - E3604
1E3621 - E3622
1E3651 - E3655
1E3677
1E3681 - E3684
1E3701 - E3704
1E3751 - E3755
1E3781 - E3784
1E5001 - E5011
1E5031 - E5068
1E5101 - E5116
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
10 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 11

GroupVariable Number
1E5141 - E5143
1E5161 - E5164
1E5201 - E5203
1E5221 - E5245
1E5251 - E5252
1E5271 - E5281
1E5301 - E5306
1E5351 - E5353
1E5381 - E5382
1E5401 - E5424
1E5426 - E5429
1E5433
1E5435
1E5451 - E5455
1E5481 - E5483
1E5501 - E5502
1QA001 - QA045
2QA046
1QA051 - QA099
1QA101 - QA174
2QA175 - QA199
1QA201 - QA225
1QA301 - QA321
2QA322
1QA323 - QA344
2QA345 - QA349
1QA351 - QA371
2QA372 - QA376
2QA378
1QA401 - QA440
2QA441 - QA499
1QA501 - QA537
1QA551 - QA579
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
11 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 12

GroupVariable Number
1QA581 - QA584
2QA585
1QA601 - QA654
2QA655 - QA688
1QA701 - QA743
2QA744 - QA753
1QA801 - QA805
1QA851 - QA898
2QA899
1QA901 - QA928
2QA929 - QA946
2QA949
1QB001 - QB002
1QB031 - QB042
2QB043 - QB049
2QB051 - QB068
1QB101 - QB110
1QB114 - QB119
1QB121 - QB149
2QB151 - QB158
1QB201 - QB203
2QB204 - QB220
1QB301 - QB310
2QB311 - QB316
1QB351 - QB352
1QB401 - QB407
1QB451 - QB453
2QB454 - QB458
1QB501 - QB539
2QB540 - QB575
2QB601 - QB629
2QB651
2QB701 - QB705
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
12 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 13

GroupVariable Number
2QB801 - QB810
2QB901 - QB904
1QD001 - QD007
2QD008 - QD012
1QD031 - QD037
2QD038 - QD046
1QD085 - QD088
1QD101 - QD105
1QD121 - QD123
2QD124 - QD127
1QD141 - QD145
2QD146 - QD149
1QD161
2QD162 - QD164
1QD191 - QD192
1QD201 - QD214
2QD215 - QD239
1QD281 - QD284
1QD301 - QD302
2QD303 - QD305
1QD321 - QD325
2QD326 - QD330
1QD351
1QD401 - QD402
2QD403
2QD407
2QD410
1QD421 - QD423
2QD424 - QD427
1QD441 - QD444
2QD445 - QD453
1QD471 - QD473
2QD474 - QD475
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
13 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 14

GroupVariable Number
1QD501 - QD507
2QD508 - QD518
1QD551 - QD554
2QD555 - QD558
2QD571 - QD572
2QD581 - QD583
2QD601 - QD607
2QD621 - QD624
2QD641
2QD661 - QD663
2QD681 - QD685
2QD691 - QD692
2QD701 - QD702
2QD711 - QD717
2QD741
2QD761 - QD769
2QD781 - QD782
2QD791
2QD801 - QD804
2QD821 - QD828
1QD901 - QD905
2QD906 - QD910
1QD931 - QD932
2QD951 - QD954
2QD971 - QD973
2QD991 - QD992
2QE001 - QE002
1QL001 - QL004
2QL005 - QL008
1QL031 - QL032
2QL081
2QL501 - QL515
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
14 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 15

2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
Accomplishment of this service bulletin will detect cracks if present in the aft pressure bulkhead web.
A cracked aft pressure bulkhead web may result in difficulty in achieving or maintaining cabin
pressurization, or result in rapid decompression.
Boeing received 13 reports of cracks in the aft pressure bulkhead web ranging from 0.75 inches to
11.8 inches in length at Left Buttock Line (LBL) 61, between Water Line (WL) 220 and WL 228. The
cracks originated at the hydraulic line support brackets which were installed in production after airplane
Line Number 1336, or in accordance with Service Bulletin 727-29-0057. The cracks were found in
airplanes which had accumulated flight hours ranging from 14,939 to 39,369 and flight cycles ranging
from 10,685 to 29,357. The cracks are attributed to fatigue of the aft pressure bulkhead web due to
vibrations from the number 1 engine hydraulic pump line in addition to normal pressurization cycles.
Material analysis revealed multiple crack initiation sites and no evidence of corrosion.
This service bulletin gives instructions for initial and repeat inspections of the aft pressure bulkhead
web for any crack and to install a preventive modification if no crack is found or to install a repair if any
crack is found. Accomplishment of this service bulletin will make sure that cracks in the aft pressure
bulkhead web are prevented or detected and repaired before the structural integrity of the aft pressure
bulkhead is degraded.
Boeing Service Related Problem 727-SRP-53-0314 is related to this service bulletin.
D. Description
Group 1, Configuration 1; Group 2:
Get access to the aft pressure bulkhead web. Do a detailed inspection for any crack in the aft pressure
bulkhead web around the hydraulic line support bracket area. If no crack is found, either repeat the
inspection in accordance with Paragraph 1.E., Compliance or accomplish the preventive modification
in accordance with this service bulletin. If any crack is found, accomplish the repair in accordance with
this service bulletin. If any crack is found to exceed the trim out limits given in this service bulletin
contact Boeing for repair instructions and do the repair.
Group 1, Configuration 2:
Get access to the aft pressure bulkhead web. Do a detailed inspection for any crack in the aft pressure
bulkhead web between WL 217 and WL 230, and LBL 48 and LBL 66. If no crack is found, repeat the
detailed inspection at intervals given in Paragraph 1.E., Compliance. If any crack is found, contact
Boeing for repair instructions and do the repair.
The work in this service bulletin is done in the maintenance zone(s) given below.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
15 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 16

Group 1:
Affected Maintenance Zones
ZoneModel
2-38, 2-39, 2-46727, 727-100, 727-100C, 727-
200, 727C
Group 2:
Affected Maintenance Zones
ZoneModel
2-38, 2-39, 2-46727-200, 727-200F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Federal Aviation Administration Airworthiness Directive FAA AD 98-11-03 R1 is related to this service
bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
16 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 17

Group 1, Configuration 1; Group 2:
Table 1: Inspection for cracking in the aft pressure bulkhead web
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
6,000 Flight Cycles
(a)
Within 3,500 Flight Cy-
cles from the date on this
service bulletin
Do a Detailed Inspection for any
crack in the aft pressure bulkhead
web between Water Line WL 217-
230 and Buttock Line BL 48L-66L
in accordance with paragraph
3.B.1.c
Bulkhead area not inspect-
ed within the last 3,500
Flight Cycles
6,000 Flight Cycles
(a)
Within 7,000 Flight Cy-
cles since the previous
inspection
Do a Detailed Inspection for any
crack in the aft pressure bulkhead
web between Water Line WL 217-
230 and Buttock Line BL 48L-66L
in accordance with paragraph
3.B.1.c
Bulkhead area inspected
within the last 3,500 Flight
Cycles
(a)Before further flightAccomplish the repair in accor-
dance with paragraph 3.B.2
If any crack is found
(a)Before further flightContact Boeing for repair instruc-
tions and do the repair
If any crack is found that
exceeds the limits given in
paragraph 3.B.2
(a) Installation of the repair or the preventive modification is the terminating action for the repeat inspections.
Group 1, Configuration 2:
Table 2: Inspection for cracking in the aft pressure bulkhead web
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
12,000 Flight Cy-
cles
Within 3,500 Flight Cy-
cles from the date on this
service bulletin
Do a Detailed Inspection for any
crack in the aft pressure bulkhead
web between WL 217-230 and BL
48L-66L in accordance with para-
graph 3.B.1.d
Bulkhead area not inspect-
ed within the last 3,500
Flight Cycles
12,000 Flight Cy-
cles
Within 7,000 Flight Cy-
cles since the previous
inspection
Do a Detailed Inspection for any
crack in the aft pressure bulkhead
web between WL 217-230 and BL
48L-66L in accordance with para-
graph 3.B.1.d
Bulkhead area inspected
within the last 3,500 Flight
Cycles
-Before further flightContact Boeing for repair instruc-
tions and do the repair
If any crack is found
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
17 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 18

Group 1, Configuration 1; Group 2:
Table 3: Inspection for cracking in the aft pressure bulkhead web with Modification Doubler or Repair
Doubler installed.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
2,000 Flight CyclesWithin 40,000 Flight Cy-
cles from the time of Pre-
ventive Modification Dou-
bler Installation
Do a High Frequency Eddy Cur-
rent (HFEC) inspection of the Aft
Pressure Bulkhead Web on the
aft side of the Bulkhead around
the periphery of the modification
doubler edges in accordance with
paragraph 3.B.5.a.(4)
All Airplanes with Preven-
tive Modification Doubler
Installed per paragraph
3.B.3.c
1,000 Flight Cycles
if the most recent
inspection was the
Detailed inspection
Within 40,000 Flight Cy-
cles from the time of the
Repair Doubler Installation
Do a Detailed inspection of the
Aft Pressure Bulkhead Web on
the aft side of the Bulkhead along
the peripheral fasteners common
to the repair doubler in accor-
dance with paragraph 3.B.5.a.(1)
or 3.B.5.a.(2) or 3.B.5.a.(3)
All Airplanes with Repair
Doubler Installed per
paragraph 3.B.2.b, or
3.B.2.c, or 3.B.2.d
--OR
6,000 Flight Cycles
if the most recent
inspection was the
HFEC inspection
Within 40,000 Flight Cy-
cles from the time of the
Repair Doubler Installation
Do a HFEC inspection of the Aft
Pressure Bulkhead Web on the
aft side of the Bulkhead around
the peripheral fasteners common
to the repair doubler in accor-
dance with paragraph 3.B.5.a.(1)
or 3.B.5.a.(2) or 3.B.5.a.(3)
-Before further flightContact Boeing for repair instruc-
tions and do the repair
If any crack is found
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
For airplanes identified in this service bulletin, Revision 0, the repair and/or modification of this service
bulletin, Revision 0, have been reviewed as required by paragraph (g) of FAA AD 98-11-03 R1. The
repair and/or modification are in the area of Structurally Significant Item F-28 of Supplemental Structural
Inspection Document, D6-48040-1, but all F-28 inspections remain effective with the repair and/or
modification installed. Therefore, an alternative inspection is not necessary for F-28. Do the existing
F-28 inspection as required per paragraph (b) and (c) of FAA AD 98-11-03 R1.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
18 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 19

If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection/repair for each
airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with
operator task hour data if necessary. The estimate does not include lost time. These are some examples
of lost time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Group 1, Configuration 1; Group 2:
Table 1 - Manpower for Inspection only
Elapsed HoursTask HoursNumber of PersonsTask
5.5011.002Open Access
0.250.251Figure 1
6.5013.002Close Access
12.2524.25TOTAL FOR EACH AIRPLANE
Group 1, Configuration 1; Group 2:
Table 2 - Manpower for Inspection and Repair Installation
Elapsed HoursTask HoursNumber of PersonsTask
5.5011.002Open Access
0.250.251Figure 1
5.2510.502Figure 3
5.2510.502Figure 4
7.0014.002Figure 5
4.258.502Figure 6
4.008.002Figure 7
4.258.502Figure 8
4.008.002Figure 9
4.258.502Figure 10
4.008.002Figure 11
6.5013.002Close Access
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
19 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 20

Group 1, Configuration 1; Group 2:
Table 2 - Manpower for Inspection and Repair Installation
Elapsed HoursTask HoursNumber of PersonsTask
54.50100.75TOTAL FOR EACH AIRPLANE
Group 1, Configuration 1; Group 2:
Table 3 - Manpower for Inspection and Preventive Modification
Elapsed HoursTask HoursNumber of PersonsTask
5.5011.002Open Access
0.250.251Figure 1
3.003.001Figure 12
1.001.001Figure 13
6.5013.002Close Access
16.2528.25TOTAL FOR EACH AIRPLANE
Group 1, Configuration 2:
Table 4 - Manpower for Inspection
Elapsed HoursTask HoursNumber of PersonsTask
2.004.002Open Access
0.250.251Figure 2
2.004.002Close Access
4.258.25TOTAL FOR EACH AIRPLANE
Group 1, Configuration 1; Group 2:
Table 5 - Post Repair Detailed Inspection
Elapsed HoursTask HoursNumber of PersonsTask
2.004.002Open Access
2.002.001FIGURE 14
2.002.001FIGURE 15
2.252.251FIGURE 16
2.004.002Close Access
Group 1, Configuration 1; Group 2:
Table 6 - Post Modification / Post Repair High Frequency Eddy Current (HFEC) Inspection
Elapsed HoursTask HoursNumber of PersonsTask
2.004.002Open Access
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
20 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 21

Group 1, Configuration 1; Group 2:
Table 6 - Post Modification / Post Repair High Frequency Eddy Current (HFEC) Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.751.751FIGURE 14
1.751.751FIGURE 15
2.002.001FIGURE 16
1.001.001FIGURE 17
2.004.002Close Access
H. Weight and Balance Changes
Group 1, Configuration 1; Group 2:
Weight and Balance Changes for Preventive Modification
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+ 946.0+ 0.8727-100
+ 1042.0+ 0.8727-200
Group 1, Configuration 1; Group 2:
Weight and Balance Changes for Repair Installation
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+ 1775.0+ 1.5727-100
+ 1955.0+ 1.5727-200
Group 1, Configuration 2:
None.
I. Electrical Load Data
Not applicable.
J. References
1. Existing Data
a. Boeing Service Bulletin 727-29-0057.
b. Boeing Service Related Problem (SRP) 727-SRP-53-0314.
c. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 98-11-03.
d. Standard Overhaul Practices Manual (SOPM) 20-41-02, 20-41-05, 20-43-03, 20-50-11.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
21 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 22

e. 727 Aircraft Maintenance Manual (AMM) 25-40-00, 25-54-00, 52-62-00.
f. 727 Non-Destructive Testing (NDT) Manual Part 6, 51-00-00.
g. 727 Structural Repair Manual (SRM) 51-30-02, 51-30-05.
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Pressure Bulkhead Installation - STA 118365-16350
This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
53-10727 Structural Repair Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS and new DTI requirements for the structure
affected are contained in Paragraph 1.E., Compliance of this service bulletin.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
22 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 23

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin
does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection, and/or repair procedures given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
Group 1, Configuration 2:
None.
Group 1, Configuration 1; Group 2:
NotesNameQTYPart Number / Specification
(c)DOUBLER12024-T3 CLAD ALUMINUM,
0.063 INCH THICK
(d)FILLER12024-T3 CLAD ALUMINUM,
0.050 INCH THICK
(c)TAPERED FILLER22024-T3 CLAD ALUMINUM,
0.063 INCH THICK
(c)FILLER22024-T3 CLAD ALUMINUM,
0.063 INCH THICK
(a) (f)BOLTAs RequiredBACB30FM6A2
(a) (f)BOLTAs RequiredBACB30FM6A4
(a) (f)BOLTAs RequiredBACB30FP6A3
(a) (f)BOLTAs RequiredBACB30FP6A4
(a) (f)BOLTAs RequiredBACB30FP6A5
(a) (f)BOLTAs RequiredBACB30FP6A7
(a) (f)COLLARAs RequiredBACC30M6
(a) (f)BOLTAs RequiredBACB30KK6A3
(a) (f)BOLTAs RequiredBACB30KK6A4
(a) (f)BOLTAs RequiredBACB30KK6A5
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
23 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 24

Group 1, Configuration 1; Group 2:
NotesNameQTYPart Number / Specification
(a) (f)BOLTAs RequiredBACB30KK6A6
(a) (f)COLLARAs RequiredBACC30R6
(a) (f)BOLTAs RequiredBACB30KK8A6
(a) (f)COLLARAs RequiredBACC30R8
(a) (f)BOLTAs RequiredBACB30LE5K8X
(a) (f)WasherAs RequiredBACW10BN
(a) (f)NUTAs RequiredBACN10HR5
(b) (f)PRIMERAs RequiredBMS 10-11, TYPE I
(b) (f)PRESSURE AND ENVI-
RONMENTAL
SEALANT
As RequiredBMS 5-95, TYPE I CLASS B-1/2
OR -2
(b) (f)CORROSION INHIBIT-
ING COMPOUND
As RequiredBMS 3-23
(e) (f)CHEMICAL CONVER-
SION COATING
As RequiredTYPE 2 CLASS A
(a) Refer to 727 Structural Repair Manual Chapter 51 for alternative fasteners.
(b) See the Qualified Products List at the end of the Boeing Material Specification
(BMS) for supplier data.
(c) Fabricate from 0.063 inch thick clad aluminum as shown in figure 6, 8, 10 or
12.
(d) Fabricate from 0.050 inch thick clad aluminum as shown in figure 6, 8, 10 or
12.
(e) Refer to SOPM 20-43-03 or 727 Structural Repair Manual Chapter 51 for
material sources.
(f) The quantities required for each repair or preventive modification will vary
according to the size of the repair or preventive modification. The quantities
provided in the Figures are for typical repair or preventive modification only.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
24 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 25

E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
25 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 26

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
26 of 111
BOEING SERVICE BULLETIN 727-53-0232
BLANK PAGE

### Page 27

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Hole dimensions for standard solid rivets are in 727 SRM, Chapter 51
4. Use the approved fastener and process material substitutions in accordance with
727 SRM, Chapter 51. Alternate fasteners are listed in 727 SRM Chapter 51 and
Boeing Drawing 65-88700.
5. If the length of any fastener specified in this service bulletin does not meet the
installation standards in SRM Chapter 51, then a fastener of the same specification,
or an approved substitute, with a length which meets the installation standards in
SRM Chapter 51 may be used.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
B. WORK INSTRUCTIONS
1. PART 1 - INSPECTION
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
27 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 28

a. Get access to the aft side of the aft pressure bulkhead above WL208 through the aft passenger
door airstairs. Refer to 727 AMM 52-62-00 as an accepted procedure.
b. Remove the central stairwell side panels to get access to the rear of the aft pressure bulkhead
web. Refer to 727 AMM 25-54-00 as an accepted procedure.
c. Group 1, Configuration 1; Group 2:
(1) Do a detailed inspection of the aft side of the aft pressure bulkhead web for any crack in
the area around the hydraulic line support bracket between WL 217 to WL 230, and LBL
48 to LBL 66 in accordance with FIGURE 1.
(a) If no crack is found, do one of the following options:
1) Option 1 - Accomplish the preventive modification in accordance with Paragraph
3.B.3 PART 3 - PREVENTIVE MODIFICATION.
2) Option 2 - Repeat the detailed inspection at intervals in accordance with
Paragraph 1.E., Compliance.
(b) If any crack is found, within the limits given in this service bulletin, accomplish the
repair in accordance with Paragraph 3.B.2 Part 2 - REPAIR.
(c) If any crack is found that exceeds the limits given in this service bulletin, contact
Boeing for repair instructions and do the repair.
d. Group 1, Configuration 2:
(1) Do a detailed inspection of the aft pressure bulkhead web for any crack between Water
Line WL 217 and WL 230, and Left Buttock Line LBL 48 and LBL 66 in accordance with
FIGURE 2.
(a) If no crack is found, repeat the detailed inspection at intervals in accordance with
Paragraph 1.E., Compliance.
(b) If any crack is found contact Boeing for repair instructions and do the repair.
2. Group 1, Configuration 1; Group 2:
PART 2 - REPAIR
a. Remove panels and cabinets on the aft wall of the left aft lavatory as required to get access
to the damaged web on the forward side of the aft pressure bulkhead. Removal of the entire
left aft lavatory may be required. Refer to 727 AMM 25-40-00 as an accepted procedure.
b. For cracking less than or equal to 4.0 inches found only at the upper fastener location in the
aft pressure bulkhead web common to the hydraulic line support bracket, do the repair that
follows:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
28 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 29

(1) Trim out the cracks in accordance with FIGURE 3.
(2) Fabricate repair parts for the upper cutout in accordance with FIGURE 6.
(3) Install repair parts for the upper cutout in accordance with FIGURE 7.
c. For cracking less than or equal to 4.0 inches found only at the lower fastener location in the
aft pressure bulkhead web common to the hydraulic line support bracket, do the repair that
follows:
(1) Trim out the cracks in accordance with FIGURE 4.
(2) Fabricate repair parts for the upper cutout in accordance with FIGURE 8.
(3) Install repair parts for the upper cutout in accordance with FIGURE 9.
d. For cracking less than or equal to 10.0 inches, do the repair that follows:
(1) Trim out the cracks in accordance with FIGURE 5.
(2) Fabricate repair parts in accordance with FIGURE 10.
(3) Install repair parts in accordance with FIGURE 11.
e. If cracking more than the limits given in any of steps (b), (c) or (d) above is found, contact
Boeing for repair procedure and do the repair.
3. Group 1, Configuration 1; Group 2:
PART 3 - PREVENTIVE MODIFICATION
a. Remove panels and cabinets on the aft wall of the left aft lavatory as required to get access
to the damaged web on the forward side of the aft pressure bulkhead. Removal of the entire
left aft lavatory may be required. Refer to 727 AMM 25-40-00 as an accepted procedure.
b. Fabricate and prepare for installation of preventive modification doubler in accordance with
FIGURE 12.
c. Install the preventive modification doubler in accordance with FIGURE 13.
4. PART 4 - CLOSE ACCESS
a. Install the central stairwell side panels. Refer to 727 AMM 25-54-00 as an accepted procedure.
b. Install panels and cabinets on the aft wall of the left aft lavatory as required and install the left
aft lavatory if removed. Refer to 727 AMM 25-40-00 as an accepted procedure.
c. Put the airplane back to a serviceable condition.
5. Group 1, Configuration 1; Group 2:
PART 5 - POST MODIFICATION AND POST REPAIR INSPECTIONS
a. Do the post modification or post repair inspections at the intervals given in Paragraph 1.E.,
Compliance, Table 3 as follows:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
29 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 30

(1) If a repair is installed for a 4 inch cutout in the upper bay area, do the post repair inspection
in accordance with FIGURE 14.
(a) If no crack is found, repeat the inspection at the interval given in Paragraph 1.E.,
Compliance.
(b) If any crack is found, contact Boeing for repair instructions and do the repair.
(2) If a repair is installed for a 4 inch cutout in the lower bay area, do the post repair inspection
in accordance with FIGURE 15.
(a) If no crack is found, repeat the inspection at the interval given in Paragraph 1.E.,
Compliance.
(b) If any crack is found, contact Boeing for repair instructions and do the repair.
(3) If a repair is installed for a 10 inch cutout, do the post repair inspection in accordance
with FIGURE 16.
(a) If no crack is found, repeat the inspection at the interval given in Paragraph 1.E.,
Compliance.
(b) If any crack is found, contact Boeing for repair instructions and do the repair.
(4) If a preventive modification doubler is installed, do the post modification inspection in
accordance with FIGURE 17.
(a) If no crack is found, repeat the inspection at the interval given in Paragraph 1.E.,
Compliance.
(b) If any crack is found, contact Boeing for repair instructions and do the repair.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
30 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 31 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
B -
WL 208
STA 1183 BULKHEAD
FIGURE 1: INSPECTION OF THE AREA AROUND THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 1 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  31 of 111

### Page 32 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
LBL
61.10
TYPICAL CRACKS
18.0-
WL
223.67
WL
213.67
VIEW LOOKING FORWARD  1548928
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 1: INSPECTION OF THE AREA AROUND THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 2 OF 3)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  32 of 111

### Page 33

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Do a Detailed Inspection for any
crack between Water Line WL
217 and WL 230, and Left But-
tock Line LBL 48 and LBL 66.
1-Aft Pressure Bulkhead
Web
Inspect1
FIGURE 1: INSPECTION OF THE AREA AROUND THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
33 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 34 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 2.
STA
1183
BULKHEAD WEB
STA 1183 BULKHEAD  1549317
FIGURE 2: INSPECTION OF THE AREA WITHOUT THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 1 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  34 of 111

### Page 35 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
_BL
51.10
18.0
WL
223.67
WL
213.67
INBD
VIEW LOOKING FORWARD  1549318
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 2: INSPECTION OF THE AREA WITHOUT THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 2 OF 3)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  35 of 111

### Page 36

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Do a Detailed Inspection for any
crack between Water Line WL
217 and WL 230, and Left But-
tock Line LBL 48 and LBL 66.
1-Aft Pressure Bulkhead
Web
Inspect1
FIGURE 2: INSPECTION OF THE AREA WITHOUT THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
36 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 37 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
STA 1183 BULKHEAD  1549332
FIGURE 3: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE UPPER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 1 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  37 of 111

### Page 38 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
LBL  66 LOCATIONS
61.10
E 8
B 6  B6 B6 B6 B6 B6 B6 B|6 B6 B|6 B6 B|6
B/6 B|6 B/6
BULKHEAD
WEB CUTOUT
E 8  D09
WL  4.0 MAX
223.67
R = 0.50 IN
TYPICAL
B6 B 6 B6 B  6 B6 B6 B  6 B6 B6
B 6 B|6 1  36 B|6 B|6
WL  INBD
213.67
VIEW LOOKING FORWARD  1549327
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 3: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE UPPER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 2 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  38 of 111

### Page 39

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Remove all fasteners from holes
which will be needed to install
the repair. Refer to 727 SRM
51-30-02 as an accepted proce-
dure.
66-FastenersRemove1
-165-17944-84Support BracketRemove / Keep2
-165-17944-85FillerRemove / Keep3
Do a HFEC inspection for
cracks in all existing open fasten-
er holes in accordance with 727
NDT Part 6, 51-00-00 Figure 16.
66-Fastener Holes in Sup-
port Bracket, Aft Pres-
sure Bulkhead Web,
Stiffeners, Chords
Inspect4
Trim out cracks and make sure
the edges of the trimmed area
are smooth. Maintain a 0.50
inches minimum radius and a
2D edge margin from fasteners.
1-Aft Pressure Bulkhead
Web
Cut5
Do a High Frequency Eddy
Current (HFEC) inspection for
cracks in all the edges of the
trim out in accordance with 727
NDT Part 6, 51-00-00 Figure 4
or 23.
1-Aft Pressure Bulkhead
Web
Inspect6
Enlarge the trim area by 0.040
inch as an insurance cut. Main-
tain a 0.50 inches minimum ra-
dius and a 2D edge margin from
fasteners.
1-Trim Out AreaExtend7
FIGURE 3: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE UPPER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
39 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 40 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
STA 1183 BULKHEAD  1549333
FIGURE 4: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE LOWER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 1 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  40 of 111

### Page 41 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
LBL
61.10
BULKHEAD
WEB CUTOUT
6)
B 6 I
66 LOCATIONS
WL  R = 0.50 IN
223.67  TYPICAL
4.0 MAX
|D 5  B6 B6 B6  B 6
T
WL  INBD
213.67
VIEW LOOKING FORWARD  1549328
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 4: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE LOWER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 2 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  41 of 111

### Page 42

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Remove all fasteners from the
holes which will be needed to
install the repair doubler. Refer
to 727 SRM 51-30-02 as an ac-
cepted procedure.
66-FastenersRemove1
-165-17944-84Support BracketRemove / Keep2
-165-17944-85FillerRemove / Keep3
Do a HFEC inspection for any
crack in all existing open fasten-
er holes in accordance with 727
NDT Part 6, 51-00-00 Figure 16.
66-Fastener Holes in Sup-
port Bracket, Aft Pres-
sure Bulkhead Web,
Stiffeners, Chords
Inspect4
Trim out cracks and make sure
the edges of the trimmed area
are smooth. Maintain a 0.50
inches minimum radius and a
2D edge margin from fasteners.
1-Aft Pressure Bulkhead
Web
Cut5
Do a High Frequency Eddy
Current (HFEC) inspection for
cracks in all the edges of the
trim out in accordance with 727
NDT Part 6, 51-00-00 Figure 4
or 23.
1-Aft Pressure Bulkhead
Web
Inspect6
Enlarge the trim area by 0.040
inch as an insurance cut. Main-
tain a 0.50 inches minimum ra-
dius and a 2D edge margin from
fasteners.
1-Trim Out AreaExtend7
FIGURE 4: TRIM OUT CRACKS LESS THAN OR EQUAL TO 4 INCHES AT THE LOWER FASTENER
LOCATION OF THE HYDRAULIC LINE SUPPORT BRACKET
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
42 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 43 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
STA 1183 BULKHEAD  1549334
FIGURE 5: TRIM OUT CRACKS LESS THAN OR EQUAL TO 10 INCHES LONG AT THE HYDRAULIC LINE
SUPPORT BRACKET LOCATION
(SHEET 1 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  43 of 111

### Page 44 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67.
LBL
$1.10
82 LOCATIONS
asIN  196 B6, B6 B6 B6 B6 B6  6 B6 B6 B6 B6 B|6 B6 B/6
BULKHEAD
WEB CUTOUT
WL
223.67
• 10.0 MAX
• R = 0.50 IN
TYPICAL
IC5  B6 B6 B 6 B
WL
213.67
INBD
VIEW LOOKING FORWARD  1549329
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 5: TRIM OUT CRACKS LESS THAN OR EQUAL TO 10 INCHES LONG AT THE HYDRAULIC LINE
SUPPORT BRACKET LOCATION
(SHEET 2 OF 3)
Original Issue: September 23, 2009
727-53-0232
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  44 of 111

### Page 45

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Remove all fasteners from holes
which will be needed to install
the repair doubler. Refer to 727
SRM 51-30-02 as an accepted
procedure.
82-FastenersRemove1
-165-17944-84Support BracketRemove / Keep2
-165-17944-85FillerRemove / Keep3
Do a HFEC inspection for any
crack in all existing open fasten-
er holes in accordance with 727
NDT Part 6, 51-00-00 Figure 16.
82-Fastener Holes in Sup-
port Bracket, Aft Pres-
sure Bulkhead Web,
Stiffeners, Chords
Inspect4
Trim out cracks and make sure
the edges of the trimmed area
are smooth. Maintain a 0.50
inches minimum radius and a
2D edge margin from fasteners.
1-Aft Pressure Bulkhead
Web
Cut5
Do a High Frequency Eddy
Current (HFEC) inspection for
cracks in all the edges of the
trim out in accordance with 727
NDT Part 6, 51-00-00 Figure 4
or 23.
1-Aft Pressure Bulkhead
Web
Inspect6
Enlarge the trim area by 0.040
inch as an insurance cut. Main-
tain a 0.50 inches minimum ra-
dius and a 2D edge margin from
fasteners.
1-Trim Out AreaExtend7
FIGURE 5: TRIM OUT CRACKS LESS THAN OR EQUAL TO 10 INCHES LONG AT THE HYDRAULIC LINE
SUPPORT BRACKET LOCATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
45 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 46 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
AND C
STA 1183 BULKHEAD  1549340
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 1 OF 7)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  46 of 111

### Page 47 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
DOUBLER  REPAIR  61.10  LBL  3 TAPERED
FILLER
FILLER
BULKHEAD
WEB CUTOUT
WL  4.0 MAX
223.67  FILLER
A 6
FILLER
B6 B6 BE  B 6  B 6
R = 0.50 IN
TYPICAL  TAPERED
FILLER
WL  INBD
213.67
VIEW LOOKING FORWARD  1549323
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 2 OF 7)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  47 of 111

### Page 48 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67  REPAIR  SUPPORT
DOUBLER  BRACKET  FILLER
(12) 13) 14)
TAPERED
FILLER
AGA
B6 B6  6 B 6B 6 B 6 B 6 B6  B 6 B
B|6 B6 B6
FILLER  $E 8  А6 Д6  А|6
EI8 A/G A/6 A/6  А 6|
LE|8  А|6;
223.67  WL  ¡ES  А/6 А/6  14 BULKHEAD  WEB CUTOUT
Е|8Ì  ¡A/6 А/6 Д/6 A/6І
B 6 B6 B6 B6  B6 B6 B6  B 6
B6 B6 B6
R = 0.50 IN
TYPICAL
FILLER
FILLER
WL  INBD
213.67
VIEW LOOKING FORWARD  1549345
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 3 OF 7)
Original issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  48 of 111

### Page 49 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
BULKHEAD -
WEB
FILLER
HORIZONTAL -
STIFFENER
112131
FILLER
3 12 13 14
SUPPORT BRACKET
69121314
REPAIR DOUBLER
WL
219.60
TRACE
HORIZONTAL  HORIZONTAL
STIFFENER  STIFFENER
FWD
BULKHEAD
WEB  STA
1183
A-A
1549344
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 4 OF 7)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  49 of 111

### Page 50

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Make from 0.063 inch thick
2024-T3 clad sheet. (a) (b)
1-Repair DoublerMake1
Make from 0.050 inch thick
2024-T3 clad sheet. (b)
1-FillerMake2
Make from 0.063 inch thick
2024-T3 clad sheet. (b)
2-Tapered FillersMake3
Make from 0.063 inch thick
2024-T3 clad sheet. (b)
2-FillersMake4
Insert on the forward side of
the bulkhead web between the
bulkhead web and the horizon-
tal stiffeners.
2-Tapered FillersAlign5
Start by backdrilling holes from
removed fastener locations
first and insert skin grips to
hold parts together, then drill
the rest of the holes. Refer to
727 SRM 51-30-05 as an ac-
cepted procedure. See fasten-
er code table for hole sizes.
12-Fastener HolesDrill
Insert on the forward side of
the bulkhead web between the
bulkhead web and the horizon-
tal stiffeners.
1-Repair DoublerAlign6
Locate in the cutout between
the repair doubler and the
other filler that mates with the
support bracket.
1-FillerAlign7
On the aft side of the bulkhead
between the bulkhead web
and the support bracket.
165-17944-85FillerAlign8
Locate on the aft side of the
bulkhead web on top of the
filler and lower stiffener flange.
165-17944-84Support BracketAlign
Start by backdrilling holes from
removed fastener locations
first and insert skin grips to
hold parts together, then drill
the rest of the holes. Refer to
727 SRM 51-30-05 as an ac-
cepted procedure. See fasten-
er code table for hole sizes.
105-Fastener HolesDrill9
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 5 OF 7)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
50 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 51

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Insert on the forward side of
the bulkhead web and the
horizontal stiffener.
2-FillersAlign10
Start by backdrilling holes from
removed fastener locations
first and insert skin grips to
hold parts together, then drill
the rest of the holes. Refer to
727 SRM 51-30-05 as an ac-
cepted procedure. See fasten-
er code table for hole sizes.
4-Fastener HolesDrill11
-165-17944-84Support BracketRemove / Keep12
-165-17944-85FillerRemove / Keep
-1-FillerRemove / Keep
-1-Repair DoublerRemove / Keep
-2-Tapered FillersRemove / Keep
-2-FillersRemove / Keep
-8-All Repair PartsDeburr13
Apply to all bare metal sur-
faces and trim edges. Refer to
SOPM 20-43-03 as an accept-
ed procedure.
-TYPE 2, CLASS AChemical Conversion
Coating
Apply14
Apply 2 coats to all bare metal
surfaces and trim edges. Refer
to SOPM 20-41-02 as an ac-
cepted procedure.
-BMS 10-11, TYPE IPrimerApply
(a) Make sure the repair doubler extends a minimum of three rows of fasteners on each side, above and below
the aft pressure bulkhead web cut out. Maintain a minimum 2D edge margin and 0.50 inch corner radius.
(b) Machine finish surface smoothness of 125 microinches AA or better.
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 6 OF 7)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
51 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 52

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
If the optional rivet will be
installed instead of the
bolt and collar, hole size
should be 0.191-0.202
0.187-0.19059-Fastener HolesA
-0.216-0.21946-Fastener HolesB
-0.200-0.2034-Fastener HolesC
-0.328-0.3324-Fastener HolesD
-0.278-0.2818-Fastener HolesE
FIGURE 6: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 7 OF 7)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
52 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 53 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
B —
STA 1183 BULKHEAD  1549335
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 1 OF 6)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  53 of 111

### Page 54 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67  REPAIR
DOUBLER  FILLER
TAPERED
FILLER
B|6 B|6 B|6 B|6 B|6 B|6 B|6 B|6|
6 B 6
FILI  •A 6 A 6A61
6 A 6A6
1E 8  A 6  _ A 6  6 A  _AL
223.67  WL  A248A2  WEB CUTOUT  BULKHEAD
E 8
\E|8
B 6  B 6 B6 B  B 6  B 6B 6
B 6 B 6
5) €
FILLER  R = 0.50 IN  TAPERED
TYPICAL  FILLER
121 LOCATIONS
WL  INBD
213.67
VIEW LOOKING FORWARD  1549360
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 2 OF 6)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  54 of 111

### Page 55 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
BULKHEAD -
WEB
FILLER
poo
HORIZONTAL -
STIFFENER
FILLER
030
SUPPORT BRACKET
139
REPAIR DOUBLER
WL
219.60
TRACE
HORIZONTAL  HORIZONTAL
STIFFENER  STIFFENER
FWD
BULKHEAD
WEB  STA
1183
A-A
1549755
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 3 OF 6)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  55 of 111

### Page 56

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Apply to all mating surfaces of
the repair parts. Refer to
SOPM 20-50-11 as an accept-
ed procedure.
-BMS 5-95, TYPE I
CLASS B-1/2 OR -2
Pressure and Environ-
mental Sealant
Apply1
Insert on the forward side of
the bulkhead web between the
bulkhead web and the horizon-
tal stiffeners.
2-Tapered FillersAlign2
Hold the tapered fillers in
place using skin grips.
2-Tapered FillersHold
Insert on the forward side of
the bulkhead web between the
bulkhead web and the horizon-
tal stiffeners.
1-Repair DoublerAlign3
Locate in the cutout between
the repair doubler and the
other filler that mates with the
support bracket.
1-FillerAlign4
On the aft side of the bulkhead
between the bulkhead web
and the support bracket.
165-17944-85FillerAlign5
Locate on the aft side of the
bulkhead web on top of the
filler and lower stiffener flange.
165-17944-84Support BracketAlign
Hold repair parts using skin
grips.
6-All Repair PartsHold6
Insert on the forward side of
the bulkhead web and the
horizontal stiffener.
2-FillersAlign7
Apply to all non-Aluminum
fasteners before installation.
Refer to SOPM 20-50-11 as
an accepted procedure. (a)
-BMS 5-95, TYPE I
CLASS B-1/2 OR -2
Pressure and Environ-
mental Sealant
Apply8
See fastener code table.121-FastenersInstall (New)
Make a fillet seal around the
repair doubler. Refer to SOPM
20-50-11 as an accepted pro-
cedure.
-BMS 5-95, TYPE I
CLASS B-1/2 OR -2
Pressure and Environ-
mental Sealant
Apply9
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 4 OF 6)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
56 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 57

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Apply to the forward side of
the repaired area. Refer to
SOPM 20-41-05 as an accept-
ed procedure.
-BMS 3-23Corrosion Inhibiting
Compound
Apply10
(a) Do not apply sealant to rivets.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
If the optional rivets are
installed, the hole size
should be 0.191-0.202
inches.
0.187-0.19055BACB30FM6A2
(BACR15BB6D5 option-
al)
BOLTA
If the optional rivets are
installed, the hole size
should be 0.191-0.202
inches.
0.187-0.1904BACB30FM6A4
(BACR15BB6D9 option-
al)
BOLT
--59BACC30M6COLLAR
-0.216-0.21921BACB30KK6A3BOLTB
-0.216-0.2196BACB30KK6A4BOLT
0.216-0.21918BACB30KK6A5BOLT
-0.216-0.2191BACB30KK6A6BOLT
--46BACC30R6COLLAR
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 5 OF 6)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
57 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 58

MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
-0.200-0.2034BACB30FP6A7BOLTC
--4BACC30M6COLLAR
-0.328-0.3324BACB30LE5K8XBOLTD
--4BACW10BN5WASHER
--4BACN10HR5NUT
-0.278-0.2818BACB30KK8A6BOLTE
--8BACC30R8COLLAR
FIGURE 7: TYPICAL REPAIR INSTALLATION FOR UPPER 4 INCH CRACK CUTOUT
(SHEET 6 OF 6)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 23, 2009
727-53-0232
58 of 111
BOEING SERVICE BULLETIN 727-53-0232

### Page 59 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
This Figure applies only to: Group 1, Configuration 1; Group 2.
STA
1183
BULKHEAD WEB
B AND C
STA 1183 BULKHEAD  1549341
FIGURE 8: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR LOWER 4 INCH CRACK CUTOUT
(SHEET 1 OF 7)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  59 of 111

### Page 60 (OCR)

BOEING SERVICE BULLETIN 727-53-0232
LBL
48
WL
233.67
REPAIR
DOUBLER  61.10  LBL  3 TAPERED
FILLER
В6 В|6 В|6 B|є B|6 B|є B|6 B|є В6В6 В
FILLER
JA s  2 FILLER
WL
223.67
BULKHEAD
WEB CUTOUT
4.0 MAX
FILLER
B 6 B6
R = 0.50 IN TAPERED  TYPICAL
FILLER
WL  INBD
213.67
VIEW LOOKING FORWARD  1549760
FIGURE 8: FABRICATION OF PARTS FOR TYPICAL REPAIR FOR LOWER 4 INCH CRACK CUTOUT
(SHEET 2 OF 7)
Original Issue: September 23, 2009
BOEING PROPRIETARY -  727-53-0232
Copyright © Unpublished Work - See page 1 for details.  60 of 111

The text continues at https://openairdocs.org/service-documents/boeing/sb-727-53-0232/file/f05e6568320d.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
