# Boeing Special Attention Service Bulletin 727-57-0187: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2013-0206; AD 2013-14-02 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 727-57-0187](https://openairdocs.org/service-documents/boeing/sb-727-57-0187.md)
- Title as filed: U.S. DOT/FAA - Service Information
- Pages: 49
- PDF: https://openairdocs.org/files/sha256/1f/d1/1fd19c8588826bb76997c82b4cb4507ebbec435682631e512660367969c8babd
- Page: https://openairdocs.org/service-documents/boeing/sb-727-57-0187/file/1fd19c858882

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
Number: 727-57-0187
Original Issue: March 08, 2012
ATA System: 5714
SUBJECT: WINGS - Wing Center Box - Upper Skin and Rear Spar Upper Chord Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2012 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
1 of 49
3.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
2 of 49
BOEING SERVICE BULLETIN 727-57-0187
BLANK PAGE

### Page 3

Table of Contents
Summary ...................................................... 5
1. PLANNING INFORMATION ........................................ 9
A. Effectivity ................................................ 9
1. Airplanes ............................................. 9
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 4
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 2 0
G. Manpower .............................................. 2 1
H. Weight and Balance Changes .................................... 2 2
I. Electrical Load Data ......................................... 2 2
J. References .............................................. 2 2
1. Existing Data .......................................... 2 2
2. Data supplied with this Service Bulletin ............................ 2 2
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 2 2
K. Publications Affected ........................................ 2 3
L. Interchangeability and Intermixability of Parts ........................... 2 3
2. MATERIAL INFORMATION ........................................ 2 5
A. Material - Price and Availability ................................... 2 5
B. Industry Support Information .................................... 2 5
C. Parts Necessary For Each Airplane ................................. 2 5
1. Kits/Parts ............................................ 2 5
2. Parts and Materials Supplied by the Operator ........................ 2 5
3. Parts Modified and Reidentified ................................ 2 5
4. Parts Removed and Not Replaced .............................. 2 5
D. Parts Necessary to Change Spares ................................. 2 5
E. Special Tooling - Price and Availability ............................... 2 6
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 6
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 7
A. GENERAL INFORMATION ..................................... 2 7
B. WORK INSTRUCTIONS ....................................... 2 7
FIGURE 1: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD HORIZONTAL FLANGE .......................... 3 2
FIGURE 2: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS [Group 1] .............................. 3 5
FIGURE 3: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS REQUIRING SEALANT REMOVAL [Group 2] .......... 3 8
FIGURE 4: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS WITHOUT SEALANT REMOVAL ................ 4 1
FIGURE 5: WINGS - WING CENTER BOX - EXTERNAL FUEL TANK INSPECTION OF THE UPPER SKIN
AND PRESSURE SEAL AT STA 870 ............................. 4 4
FIGURE 6: WINGS - WING CENTER SECTION - REAR SPAR UPPER CHORD - INTERNAL FUEL TANK
SEALANT APPLICATION ................................... 4 7
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
3 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 4

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
4 of 49
BOEING SERVICE BULLETIN 727-57-0187
BLANK PAGE

### Page 5

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 727-57-0187Original Issue: March 08, 2012
ATA System: 5714
SUBJECT: WINGS - Wing Center Box - Upper Skin and Rear Spar Upper Chord Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions to inspect the upper skin and the rear spar upper chord of the wing center
box, at Body Station (STA) 870 for cracking or corrosion. The upper skin and the rear spar upper chord of the
wing center box are classified as principal structural elements. If the work in this service bulletin is not done,
undetected cracking or corrosion in this area could severely limit the load carrying capabilities of the structure
which could result in the inability of the remaining structure to carry limit load which would preclude the continued
safe flight of the airplane.
Several operators have reported spanwise cracks and corrosion in the upper skin and rear spar upper chord
between Left Buttock Line (LBL) 70.50 and Right Buttock Line (RBL) 70.50, at STA 870. The crack sizes ranged
from 0.125 inches to 12 inches. The airplanes had accumulated between 31, 679 and 61,359 total flight hours
and between 17,754 and 58,796 total flight cycles. Analysis has shown that the cracks are a result of stress
corrosion which is a common problem in the 7178-T651 and 7178-T6511 aluminum from which the wing center
box upper skin and some rear spar upper chords are manufactured. All 727-100/-200 airplanes were delivered
with 7178-T651 aluminum plate upper skin panels and therefore all these airplanes are affected.
Corrosion occurrences in the wing center section are known issues. Boeing Service Bulletin 727-57-0170 was
issued for inspections and application of a corrosion inhibitor for external portions of the wing center section.
Additionally, multiple Structural Item Interim Advisories (SIIA) were issued for corrosion incidences to wing center
section stiffeners, webs, upper skins and chords at the rear spar. However, none of these documents resolves
the issue of cracking or corrosion at the wing center box upper skin and rear spar. Accomplishment of this service
bulletin will make sure that cracking or corrosion at the upper skin and the rear spar upper chord at the wing
center box, STA 870 are detected.
Boeing Service Related Problem (SRP) 727-SRP-52-0228 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 727 FTD 57-08003 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
5 of 49

### Page 6

ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., ComplianceNoAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected
(Flight Crew Operations Manual and/or
FAA Approved Airplane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Defuel all tanks. Get access to the lower surface of the wing center box upper skin near the aft rear spar through
the center fuel tank. Between LBL 70.50 and RBL 70.50, at STA 870, do the following inspections: Do a High
Frequency Eddy Current (HFEC) inspection or a detailed inspection for cracking around the forward fastener
row in the rear spar upper chord horizontal flange. Do a Low Frequency Eddy Current (LFEC) inspection around
the aft fastener row in the rear spar upper chord horizontal flange for cracking in the upper skin and the rear
spar upper chord horizontal flange. Do a HFEC inspection or a detailed inspection for cracking in the rear spar
upper chord radius. If any crack is found, contact Boeing for repair instructions and do the repair. If no cracking
is found, do the repeat inspections at the intervals given in Paragraph 1.E., Compliance.
Get access to the upper surface of the wing center box upper skin near the rear spar by removing floor panels
at the wing center box. Between LBL 70.50 and RBL 70.50, at STA 870, do the following inspections: Do a
detailed inspection or a HFEC inspection for cracking in the upper skin around the forward fastener row common
to the rear spar upper chord horizontal flange. Do a detailed inspection for any damage, cracking or corrosion
in the pressure seal. If any damage, cracking or corrosion is found, contact Boeing for repair instructions and
do the repair. If no cracking is found, do the repeat inspections at the intervals given in Paragraph 1.E.,
Compliance.
EFFECTIVITY
All 727, 727-100, 727-100C, 727-200, 727-200F, 727C Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the
list of affected airplanes.
COMPLIANCE
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection procedures given in this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
6 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 7

MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
7 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 8 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
EXTERNAL FUEL TANK INSPECTION:
INSPECT THE UPPER SKIN FOR CRACKING AND
INSPECT THE PRESSURE SEAL FOR DAMAGE,
CRACKING AND CORROSION. IF ANY DAMAGE,
CRACKING OR CORROSION IS FOUND, CONTACT
BOEING FOR REPAIR INSTRUCTIONS AND DO THE
REPAIR INSTRUCTED BY BOEING.
STA
870
STA
740
RBL
70.50
LBL
70.50
INSPECTION AREA
UPPER  PRESSURE
SKIN  SEAL
INTERNAL FUEL TANK INSPECTION:
INSPECT THE UPPER SKIN, THE
REAR SPAR UPPER CHORD
HORIZONTAL FLANGE AND THE
REAR SPAR UPPER CHORD
RADIUS FOR CRACKING. IF ANY  REAR SPAR
CRACK IS  FOUND, CONTACT  UPPER CHORD
BOEING FOR REPAIR
INSTRUCTIONS AND DO THE
REPAIR INSTRUCTED BY BOEING.
A-A  - REAR SPAR WEB  2121797
Original Issue: March 08, 2012
BOEING PROPRIETARY -  727-57-0187
Copyright © Unpublished Work - See page 1 for details.  8 of 49

### Page 9

Commercial 
Airplanes
727
Service Bulletin
SPECIAL ATTENTION
Number: 727-57-0187
Original Issue: March 08, 2012
ATA System: 5714
SUBJECT: WINGS - Wing Center Box - Upper Skin and Rear Spar Upper Chord Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
DESCRIPTIONCONFIGURATIONGROUP
727, 727C, 727-100, 727-100C, and 727-200 airplanes with bladder
fuel cells at the wing center section.
-1
727, 727-100 and 727-200, 727-200F airplanes with an integral fuel
tank at the wing center section.
-2
Airplane Models:
727, 727-100, 727-100C, 727-200, 727-200F, 727C
GroupVariable Number
1E0001 - E0042
1E0101 - E0140
1E0201 - E0216
1E0301 - E0351
1E0401 - E0423
1E3001 - E3006
1E3011 - E3014
1E3021 - E3040
1E3059
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
9 of 49

### Page 10

GroupVariable Number
1E3061 - E3077
1E3101 - E3103
1E3111 - E3118
1E3141 - E3152
1E3171 - E3177
1E3201 - E3206
1E3221 - E3224
1E3241 - E3290
1E3341 - E3350
1E3401 - E3421
1E3451 - E3452
1E3471 - E3474
1E3501 - E3513
1E3516 - E3522
2E3523
1E3551 - E3553
1E3571 - E3578
1E3601 - E3604
1E3621 - E3622
1E3651 - E3655
1E3677
1E3681 - E3682
2E3683 - E3684
1E3701 - E3704
1E3751 - E3755
1E3781 - E3784
1E5001 - E5011
1E5031 - E5068
1E5101 - E5116
1E5141 - E5143
1E5161 - E5164
1E5201 - E5203
1E5221 - E5245
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
10 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 11

GroupVariable Number
1E5251 - E5252
1E5271 - E5281
1E5301 - E5306
1E5351 - E5353
1E5381 - E5382
1E5401 - E5424
1E5426 - E5429
1E5433
1E5435
1E5451 - E5455
1E5481 - E5483
1E5501 - E5502
1QA001 - QA021
2QA022 - QA023
1QA024 - QA025
2QA026 - QA046
1QA051 - QA058
2QA059 - QA099
1QA101 - QA141
2QA142 - QA199
1QA201 - QA225
1QA301 - QA316
2QA317 - QA324
1QA325 - QA329
2QA330 - QA349
1QA351 - QA368
2QA369 - QA376
2QA378
1QA401 - QA428
2QA429 - QA499
1QA501 - QA532
2QA533 - QA537
1QA551 - QA567
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
11 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 12

GroupVariable Number
2QA568 - QA573
1QA574 - QA575
2QA576
1QA577 - QA578
2QA579
2QA581 - QA585
1QA601 - QA626
2QA627 - QA688
1QA701 - QA724
2QA725 - QA753
1QA801 - QA805
1QA851 - QA853
2QA854 - QA899
1QA901 - QA906
2QA907 - QA946
2QA949
1QB001 - QB002
1QB031 - QB033
2QB034 - QB049
2QB051 - QB068
1QB101 - QB102
2QB103 - QB110
2QB114 - QB119
2QB121 - QB149
2QB151 - QB158
2QB201 - QB220
2QB301 - QB316
2QB351 - QB352
2QB401 - QB407
2QB451 - QB458
2QB501 - QB575
2QB601 - QB629
2QB651
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
12 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 13

GroupVariable Number
2QB701 - QB705
2QB801 - QB810
2QB901 - QB904
2QD001 - QD012
2QD031 - QD046
2QD085 - QD088
2QD101 - QD105
2QD121 - QD127
2QD141 - QD149
2QD161 - QD164
2QD191 - QD192
2QD201 - QD239
2QD281 - QD284
2QD301 - QD305
2QD321 - QD330
2QD351
2QD401 - QD403
2QD407
2QD410
2QD421 - QD427
2QD441 - QD453
2QD471 - QD475
2QD501 - QD518
2QD551 - QD558
2QD571 - QD572
2QD581 - QD583
2QD601 - QD607
2QD621 - QD624
2QD641
2QD661 - QD663
2QD681 - QD685
2QD691 - QD692
2QD701 - QD702
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
13 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 14

GroupVariable Number
2QD711 - QD717
2QD741
2QD761 - QD769
2QD781 - QD782
2QD791
2QD801 - QD804
2QD821 - QD828
2QD901 - QD910
2QD931 - QD932
2QD951 - QD954
2QD971 - QD973
2QD991 - QD992
2QE001 - QE002
2QL001 - QL008
2QL031 - QL032
2QL081
2QL501 - QL515
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
This service bulletin gives instructions to inspect the upper skin and the rear spar upper chord of the
wing center box, at Body Station (STA) 870 for cracking or corrosion. The upper skin and the rear spar
upper chord of the wing center box are classified as principal structural elements. If the work in this
service bulletin is not done, undetected cracking or corrosion in this area could severely limit the load
carrying capabilities of the structure which could result in the inability of the remaining structure to carry
limit load which would preclude the continued safe flight of the airplane.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
14 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 15

Several operators have reported spanwise cracks and corrosion in the upper skin and rear spar upper
chord between Left Buttock Line (LBL) 70.50 and Right Buttock Line (RBL) 70.50, at STA 870. The
crack sizes ranged from 0.125 inches to 12 inches. The airplanes had accumulated between 31, 679
and 61,359 total flight hours and between 17,754 and 58,796 total flight cycles. Analysis has shown
that the cracks are a result of stress corrosion which is a common problem in the 7178-T651 and
7178-T6511 aluminum from which the wing center box upper skin and some rear spar upper chords
are manufactured. All 727-100/-200 airplanes were delivered with 7178-T651 aluminum plate upper
skin panels and therefore all these airplanes are affected.
Corrosion occurrences in the wing center section are known issues. Boeing Service Bulletin 727-57-0170
was issued for inspections and application of a corrosion inhibitor for external portions of the wing
center section. Additionally, multiple Structural Item Interim Advisories (SIIA) were issued for corrosion
incidences to wing center section stiffeners, webs, upper skins and chords at the rear spar. However,
none of these documents resolves the issue of cracking or corrosion at the wing center box upper skin
and rear spar. Accomplishment of this service bulletin will make sure that cracking or corrosion at the
upper skin and the rear spar upper chord at the wing center box, STA 870 are detected.
Boeing Service Related Problem (SRP) 727-SRP-52-0228 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 727 FTD 57-08003 is related to this service bulletin.
D. Description
Defuel all tanks. Get access to the lower surface of the wing center box upper skin near the aft rear
spar through the center fuel tank. Between LBL 70.50 and RBL 70.50, at STA 870, do the following
inspections: Do a High Frequency Eddy Current (HFEC) inspection or a detailed inspection for cracking
around the forward fastener row in the rear spar upper chord horizontal flange. Do a Low Frequency
Eddy Current (LFEC) inspection around the aft fastener row in the rear spar upper chord horizontal
flange for cracking in the upper skin and the rear spar upper chord horizontal flange. Do a HFEC
inspection or a detailed inspection for cracking in the rear spar upper chord radius. If any crack is found,
contact Boeing for repair instructions and do the repair. If no cracking is found, do the repeat inspections
at the intervals given in Paragraph 1.E., Compliance.
Get access to the upper surface of the wing center box upper skin near the rear spar by removing floor
panels at the wing center box. Between LBL 70.50 and RBL 70.50, at STA 870, do the following
inspections: Do a detailed inspection or a HFEC inspection for cracking in the upper skin around the
forward fastener row common to the rear spar upper chord horizontal flange. Do a detailed inspection
for any damage, cracking or corrosion in the pressure seal. If any damage, cracking or corrosion is
found, contact Boeing for repair instructions and do the repair. If no cracking is found, do the repeat
inspections at the intervals given in Paragraph 1.E., Compliance.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
1-74727, 727-100, 727-100C, 727-
200, 727C
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
15 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 16

Group 2:
Affected Maintenance Zones
ZoneModel
1-74727, 727-100, 727-200, 727-
200F
E. Compliance
Group 1:
Table 1: Wing Center Box - Internal Fuel Tank Inspection of the Upper Skin and Rear Spar Upper
Chord
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
--Do an inspection for cracking
around the forward fastener row
in the rear spar upper chord hori-
zontal flange between Left But-
tock Line (LBL) 70.50 and Right
Buttock Line (RBL) 70.50, at Body
Station (STA) 870, using one of
the following options:
All Airplanes.
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 1: Do a High Frequency
Eddy Current (HFEC) inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.a.(1)(a).
OR
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 2: Do a detailed inspec-
tion in accordance with Accom-
plishment Instructions paragraph
3.B.2.a.(1)(b).
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
Do a Low Frequency Eddy Cur-
rent (LFEC) inspection around the
aft fastener row in the rear spar
upper chord horizontal flange for
cracking in the upper skin and the
rear spar upper chord horizontal
flange between LBL 70.50 and
RBL 70.50, at STA 870, in accor-
dance with Accomplishment In-
structions paragraph 3.B.2.a.(2).
All Airplanes.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
16 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 17

Group 1:
Table 1: Wing Center Box - Internal Fuel Tank Inspection of the Upper Skin and Rear Spar Upper
Chord
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
--Do an inspection for cracking in
the rear spar upper chord radius
between LBL 70.50 and RBL
70.50, at STA 870, using one of
the following options:
All Airplanes.
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 1: Do a detailed inspec-
tion in accordance with Accom-
plishment Instructions paragraph
3.B.2.a.(3)(a).
OR
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 2: Do a HFEC inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.a.(3)(b).
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
17 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 18

Group 2:
Table 2: Wing Center Box - Internal Fuel Tank Inspection of the Upper Skin and Rear Spar Upper
Chord
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
--Do an inspection for cracking
around the forward fastener row
in the rear spar upper chord hori-
zontal flange between Left But-
tock Line (LBL) 70.50 and Right
Buttock Line (RBL) 70.50, at Body
Station (STA) 870, using one of
the following options:
All Airplanes.
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 1: Do a High Frequency
Eddy Current (HFEC) inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.a.(1)(a).
OR
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 2: Do a detailed inspec-
tion in accordance with Accom-
plishment Instructions paragraph
3.B.2.a.(1)(b).
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
Do a Low Frequency Eddy Cur-
rent (LFEC) inspection around the
aft fastener row in the rear spar
upper chord horizontal flange for
cracking in the upper skin and the
rear spar upper chord horizontal
flange between LBL 70.50 and
RBL 70.50, at STA 870, in accor-
dance with Accomplishment In-
structions paragraph 3.B.2.a.(2).
All Airplanes.
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
18 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 19

Group 2:
Table 2: Wing Center Box - Internal Fuel Tank Inspection of the Upper Skin and Rear Spar Upper
Chord
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
--Do an inspection for cracking in
the rear spar upper chord radius
between LBL 70.50 and RBL
70.50, at STA 870, using one of
the following options:
All Airplanes.
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 1: Do a detailed inspec-
tion in accordance with Accom-
plishment Instructions paragraph
3.B.2.a.(4)(a).
OR
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 2: Do a HFEC inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.a.(4)(b).
OR
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 3: Do a HFEC inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.a.(4)(c).
NOTE: Removal of sealant from
the rear spar upper chord radius
is not required for Option 3 inspec-
tion.
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
19 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 20

All Groups:
Table 3: Wing Center Box - External Fuel Tank Inspection of the Upper Skin and Pressure Seal
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
--Do an inspection for cracking in
the upper skin around the forward
fastener row common to the rear
spar upper chord horizontal flange
between LBL 70.50 and RBL
70.50, at STA 870, using one of
the following options:
All Airplanes.
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 1: Do a detailed inspec-
tion in accordance with Accom-
plishment Instructions paragraph
3.B.2.b.(1)(a).
OR
6 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
OPTION 2: Do a HFEC inspection
in accordance with Accomplish-
ment Instructions paragraph
3.B.2.b.(1)(b).
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any crack found.
3 years.Within 3 years af-
ter the original is-
sue date of this
service bulletin.
Do a detailed inspection for dam-
age, cracking or corrosion in the
pressure seal between LBL 70.50
and RBL 70.50, at STA 870, in
accordance with Accomplishment
Instructions paragraph 3.B.2.b.(2).
All Airplanes.
-Before further
flight.
Contact Boeing for repair instruc-
tions and do the repair instructed
by Boeing.
Any damage,
cracking or corro-
sion found.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
20 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 21

G. Manpower
The table below shows an estimate of the task hours necessary to do this service bulletin for each
airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with
operator task hour data if necessary. The estimate does not include lost time. These are some examples
of lost time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
2.008.004Preparation
2.339.304Open Access
5.0010.002FIGURE 1, OPTION 1
4.008.002FIGURE 1, OPTION 2
1.503.002FIGURE 2, OPTION 1
2.505.002FIGURE 2, OPTION 2
3.006.002FIGURE 5, OPTION 1
4.008.002FIGURE 5, OPTION 2
2.008.004Restoration
8.6517.302Close Access
(a)(a)TOTAL FOR EACH AIRPLANE
(a) The total task hours and total elapsed hours for each airplane depend on which inspection
options are accomplished. Operators should add the hours for each applicable task to
calculate the total hours for each airplane.
Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
2.008.004Preparation
4.3317.304Open Access
5.0010.002FIGURE 1, OPTION 1
4.008.002FIGURE 1, OPTION 2
7.1014.202FIGURE 3, OPTION 1
8.1516.302FIGURE 3, OPTION 2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
21 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 22

Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
2.505.002FIGURE 4, OPTION 3
3.006.002FIGURE 5, OPTION 1
4.008.002FIGURE 5, OPTION 2
7.7515.502FIGURE 6
2.008.004Restoration
4.3317.304Close Access
(a)(a)TOTAL FOR EACH AIRPLANE
(a) The total task hours and total elapsed hours for each airplane depend on which inspection
options are accomplished. Operators should add the hours for each applicable task to
calculate the total hours for each airplane.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not applicable.
J. References
1. Existing Data
a. Boeing Service Bulletin 727-57-0170.
b. Boeing Service Related Problem (SRP) 727-SRP-52-0228.
c. Standard Overhaul Practices Manual (SOPM) 20-30-93, 20-41-05, 20-50-19.
d. 727 Aircraft Maintenance Manual (AMM) 12-30-03, 28-10-00, 28-11-21, 28-12-01, 28-12-11,
28-23-00, 51-31-00, 53-20-11.
e. 727 Fleet Team Digest (FTD) 57-08003.
f. 727 Non-Destructive Testing (NDT) Manual Part 6, 51-00-00, Part 6, 51-00-27, Part 6, 57-10-28.
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
REAR SPAR INSTALLATION - WING CENTER SECTION65-16202
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
22 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 23

The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
23 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 24

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
24 of 49
BOEING SERVICE BULLETIN 727-57-0187
BLANK PAGE

### Page 25

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection procedures given in this service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
Group 1:
NotesNameQTYPart Number / Speci-
fication
(a)Corrosion Inhibiting Compound5 ozBMS 3-23, Type 2
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
Group 2:
NotesNameQTYPart Number / Speci-
fication
(a)Corrosion Inhibiting Compound5 ozBMS 3-23, Type 2
(a)Sealant, Integral Fuel Tank5 ozBMS 5-45, Class B
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
25 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 26

E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
26 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 27

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
4. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
5. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. Boeing Service Letter 727-SL-51-041, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
B. WORK INSTRUCTIONS
1. PREPARATION AND ACCESS
a. Defuel all tanks. Refer to 727 AMM 28-23-00 as an accepted procedure.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
27 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 28

b. Group 1:
(1) Open the wing center fuel cell access panel. Refer to 727 AMM 28-12-11 as an accepted
procedure.
(2) Remove the wing center section fuel tank bladder cells. Refer to 727 AMM 28-12-01 as
an accepted procedure.
c. Group 2:
(1) Open the wing center section fuel tank access panel. Refer to 727 AMM 28-11-21 as an
accepted procedure.
(2) Purge the wing center section fuel tank. Refer to 727 AMM 28-10-00 as an accepted
procedure.
d. Open floor panels 3355, 3356, 3455 and 3456 to get access to the upper surface of the wing
center section upper skin. Refer to 727 AMM 12-30-03 and 727 AMM 53-20-11 as accepted
procedures.
2. INSPECTION
a. Internal Fuel Tank Inspection
(1) Do an inspection for cracking around the forward fastener row in the rear spar upper
chord horizontal flange between Left Buttock Line (LBL) 70.50 and Right Buttock Line
(RBL) 70.50, at Body Station (STA) 870, using one of the following options:
(a) OPTION 1: Do a High Frequency Eddy Current (HFEC) inspection in accordance
with FIGURE 1.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(b) OPTION 2: Do a detailed inspection in accordance with FIGURE 1.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(2) Do a Low Frequency Eddy Current (LFEC) inspection around the aft fastener row in the
rear spar upper chord horizontal flange for cracking in the upper skin and the rear spar
upper chord horizontal flange between LBL 70.50 and RBL 70.50, at STA 870, in
accordance with FIGURE 1.
(a) If any crack is found, contact Boeing for repair instructions and do the repair instructed
by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
28 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 29

(b) If no cracking is found, do the repeat inspections at the interval given in Paragraph
1.E., Compliance.
(3) Group 1:
Do an inspection for cracking in the rear spar upper chord radius between LBL 70.50 and
RBL 70.50, at STA 870, using one of the following options:
(a) OPTION 1: Do a detailed inspection in accordance with FIGURE 2.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(b) OPTION 2: Do a HFEC inspection in accordance with FIGURE 2.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(4) Group 2:
Do an inspection for cracking in the rear spar upper chord radius between LBL 70.50 and
RBL 70.50, at STA 870, using one of the following options:
(a) OPTION 1: Remove the sealant from the rear spar upper chord radius and do a
detailed inspection in accordance with FIGURE 3.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, apply sealant to the rear spar upper chord radius in
accordance with FIGURE 6 and do the repeat inspections at the interval given
in Paragraph 1.E., Compliance.
(b) OPTION 2: Remove the sealant from the rear spar upper chord radius and do a
HFEC inspection in accordance with FIGURE 3.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, apply sealant to the rear spar upper chord radius in
accordance with FIGURE 6 and do the repeat inspections at the interval given
in Paragraph 1.E., Compliance.
(c) OPTION 3: Do a HFEC inspection in accordance with FIGURE 4.
NOTE: Removal of sealant from the rear spar upper chord radius is not required
for Option 3 inspection.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
29 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 30

1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
b. External Fuel Tank Inspection
(1) Do an inspection for cracking in the upper skin around the forward fastener row common
to the rear spar upper chord horizontal flange between LBL 70.50 and RBL 70.50, at STA
870, using one of the following options:
(a) OPTION 1: Do a detailed inspection in accordance with FIGURE 5.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(b) OPTION 2: Do a HFEC inspection in accordance with FIGURE 5.
1) If any crack is found, contact Boeing for repair instructions and do the repair
instructed by Boeing.
2) If no cracking is found, do the repeat inspections at the interval given in
Paragraph 1.E., Compliance.
(2) Do a detailed inspection for damage, cracking or corrosion in the pressure seal between
LBL 70.50 and RBL 70.50, at STA 870, in accordance with FIGURE 5.
(a) If any damage, cracking or corrosion is found, contact Boeing for repair instructions
and do the repair instructed by Boeing.
(b) If no damage, cracking or corrosion is found, do the repeat inspections at the interval
given in Paragraph 1.E., Compliance.
3. RESTORATION AND CLOSE ACCESS
a. Apply BMS 3-23, Type 2 Corrosion Inhibiting Compound to the upper surface of the wing
center box upper skin near the rear spar. Refer to SOPM 20-41-05 as an accepted procedure.
b. Close floor panels 3355, 3356, 3455 and 3456. Refer to 727 AMM 12-30-03 and 727 AMM
53-20-11 as accepted procedures.
c. Group 1:
(1) Apply BMS 3-23, Type 2 Corrosion Inhibiting Compound to the inside of the wing center
section where inspection was done. Refer to SOPM 20-41-05 as an accepted procedure.
(2) Install the wing center section fuel tank bladder cells. Refer 727 AMM 28-12-01 to as an
accepted procedure.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
30 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 31

(3) Close the wing center fuel cell access panel. Refer to 727 AMM 28-12-11 as an accepted
procedure.
d. Group 2:
(1) Close the wing center section fuel tank access panel. Refer to 727 AMM 28-11-21 as an
accepted procedure.
e. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
31 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 32 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
RBL
70.50
LBL'
70.50
2121799
FIGURE 1: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD HORIZONTAL FLANGE
(SHEET 1 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  32 of 49

### Page 33 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
WING CENTER BOX
UPPER SKIN
PRESSURE
SEAL
REAR SPAR
UPPER
CHORD
REAR SPAR
WEB
• HFEC OR DETAILED
• INSPECTION AREA
LFEC INSPECTION  AREA  TYPICAL REAR SPAR UPPER CORNER  2121800
(INTERNAL VIEW, LOOKING AFT)
FIGURE 1: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD HORIZONTAL FLANGE
(SHEET 2 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  33 of 49

### Page 34

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)1-Rear Spar Upper ChordInspect1
(b)--Upper Skin and Rear
Spar Upper Chord
Inspect2
(a) OPTION 1: Do a High Frequency Eddy Current (HFEC) inspection for cracking around the forward fastener
row in the rear spar upper chord horizonal flange between Left Buttock Line (LBL) 70.50 and Right Buttock
Line (RBL) 70.50 in accordance with 727 NDT Part 6, 57-10-28. OPTION 2: Do a detailed inspection for
cracking around the forward fastener row in the rear spar upper chord horizontal flange between LBL
70.50 and RBL 70.50.
(b) Do a Low Frequency Eddy Current (LFEC) inspection around the aft fastener row in the rear spar upper
chord horizontal flange for cracking in the upper skin and the rear spar upper chord horizontal flange be-
tween LBL 70.50 and RBL 70.50 in accordance with 727 NDT Part 6, 57-10-28.
FIGURE 1: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD HORIZONTAL FLANGE
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
34 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 35 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
This Figure applies only to: Group 1.
STA
740
RBL
70.50
LBL
70.50
2121812
FIGURE 2: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS
(SHEET 1 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  35 of 49

### Page 36 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
WING CENTER BOX
UPPER SKIN
PRESSURE
SEAL
REAR SPAR
UPPER
CHORD
WEER SPAR
INSPECTION AREA  HFEC OR DETAILED  TYPICAL REAR SPAR UPPER CORNER  2121813
(INTERNAL VIEW, LOOKING AFT)
FIGURE 2: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS
(SHEET 2 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  36 of 49

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)--Rear Spar Upper Chord
Radius
Inspect1
(a) OPTION 1: Do a detailed inspection for cracking in the rear spar upper chord radius between LBL 70.50
and RBL 70.50. OPTION 2: Do a High Frequency Eddy Current (HFEC) inspection for cracking in the
rear spar upper chord radius between LBL 70.50 and RBL 70.50 in accordance with 727 NDT Part 6, 51-
00-00 Figure 23. Scan the probe in a manner to detect span wise cracks.
FIGURE 2: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
37 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 38 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
This Figure applies only to: Group 2.
2900
LBL
70.50
2121815
FIGURE 3: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS REQUIRING SEALANT REMOVAL
(SHEET 1 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  38 of 49

### Page 39 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
WING CENTER BOX
UPPER SKIN
1X2
PRESSURE
SEAL
REAR SPAR
UPPER
CHORD
REAR SPAR
WEB
• HFEC OR DETAILED
* INSPECTION AREA  TYPICAL REAR SPAR UPPER CORNER  2121816
(INTERNAL VIEW, LOOKING AFT)
FIGURE 3: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS REQUIRING SEALANT REMOVAL
(SHEET 2 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  39 of 49

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)--SealantRemove1
(b)--Rear Spar Upper Chord
Radius
Inspect2
(a) Remove all the sealant from the rear spar upper chord radius between Left Buttock Line (LBL) 70.50 and
Right Buttock Line (RBL) 70.50. Refer to SOPM 20-50-19 as an accepted procedure.
(b) OPTION 1: Do a detailed inspection for cracking in the rear spar upper chord radius between LBL 70.50
and RBL 70.50. OPTION 2: Do a High Frequency Eddy Current (HFEC) inspection for cracking in the
rear spar upper chord radius between LBL 70.50 and RBL 70.50 in accordance with 727 NDT Part 6, 51-
00-00 Figure 23. Scan the probe in a manner to detect span wise cracks.
FIGURE 3: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS REQUIRING SEALANT REMOVAL
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
40 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 41 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
STA
740
RBL
70.50
_BI
/0.50
2133940
FIGURE 4: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS WITHOUT SEALANT REMOVAL
(SHEET 1 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  41 of 49

### Page 42 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
WING CENTER BOX
UPPER SKIN
PRESSURE
SEAL
REAR SPAR
UPPER
CHORD
REAR SPAR
WEB
• HFEC INSPECTION
AREA
TYPICAL REAR SPAR UPPER CORNER  2133943
(INTERNAL VIEW, LOOKING AFT)
FIGURE 4: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS WITHOUT SEALANT REMOVAL
(SHEET 2 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  42 of 49

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)--Rear Spar Upper Chord
Radius
Inspect1
(a) Do a High Frequency Eddy Current (HFEC) inspection for cracking in the rear spar upper chord radius
between Left Buttock Line (LBL) 70.50 and Right Buttock Line (RBL) 70.50 in accordance with 727 NDT
Part 6, 51-00-27. Scan the probe in a manner to detect spanwise cracks. Make sure to calibrate the in-
strument for the sealant thickness that is in the radius. The maximum thickness of the sealant allowed
for this procedure is defined in 727 NDT Part 6, 51-00-27.
FIGURE 4: WINGS - WING CENTER BOX - INTERNAL FUEL TANK INSPECTION OF THE REAR SPAR
UPPER CHORD RADIUS WITHOUT SEALANT REMOVAL
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
43 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 44 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
STA
_ 6 INCHES  870
UPPER
SKIN  B
INSPECTION AREA
STA
740
RBL
70.50
REAR
SPAR
LBL
70.50
2121819
FIGURE 5: WINGS - WING CENTER BOX - EXTERNAL FUEL TANK INSPECTION OF THE UPPER SKIN
AND PRESSURE SEAL AT STA 870
(SHEET 1 OF 3)
Original Issue: March 08, 2012
BOEING PROPRIETARY -  727-57-0187
Copyright © Unpublished Work - See page 1 for details.  44 of 49

### Page 45 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
PRESSURE
SEAL
6 INCHÉS
B
WING CENTER BOX
UPPER SKIN
HFEC OR DETAILED
INSPECTION AREA
DETAILED
INSPECTION AREA  2122019
FIGURE 5: WINGS - WING CENTER BOX - EXTERNAL FUEL TANK INSPECTION OF THE UPPER SKIN
AND PRESSURE SEAL AT STA 870
(SHEET 2 OF 3)
Original Issue: March 08, 2012
Copyright © Unpublished Work - See page 1 for details.  BOEING PROPRIETARY -  727-57-0187  45 of 49

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)--Upper SkinInspect1
(b)--Pressure SealInspect2
(a) OPTION 1: Do a detailed inspection for cracking in the upper skin around the forward fastener row common
to the rear spar upper chord horizontal flange between Left Buttock Line (LBL) 70.50 and Right Buttock
Line (RBL) 70.50. OPTION 2: Do a High Frequency Eddy Current (HFEC) inspection for cracking in the
upper skin around the forward fastener row common to the rear spar upper chord horizontal flange between
LBL 70.50 and RBL 70.50 in accordance with 727 NDT Part 6, 57-10-28.
(b) Do a detailed inspection of the pressure seal between LBL 70.50 and RBL 70.50 for damage, cracking
or corrosion. Examples of damage are missing, flaking, or blistering in the paint, primer, sealant, or corrosion
inhibiting compound.
FIGURE 5: WINGS - WING CENTER BOX - EXTERNAL FUEL TANK INSPECTION OF THE UPPER SKIN
AND PRESSURE SEAL AT STA 870
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
46 of 49
BOEING SERVICE BULLETIN 727-57-0187

### Page 47 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
STA
740
RBL
70.50
_BI
70.50
2121817
FIGURE 6: WINGS - WING CENTER SECTION - REAR SPAR UPPER CHORD - INTERNAL FUEL TANK
SEALANT APPLICATION
(SHEET 1 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  47 01 49

### Page 48 (OCR)

BOEING SERVICE BULLETIN 727-57-0187
WING CENTER BOX
UPPER SKIN
PRESSURE
SEAL
REAR SPAR
UPPER
CHORD
REAR SPAR
WEB
TYPICAL REAR SPAR UPPER CORNER  2121818
(INTERNAL VIEW, LOOKING AFT)
FIGURE 6: WINGS - WING CENTER SECTION - REAR SPAR UPPER CHORD - INTERNAL FUEL TANK
SEALANT APPLICATION
(SHEET 2 OF 3)
Original Issue: March 08, 2012
727-57-0187
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  48 of 49

### Page 49

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)--Rear Spar Upper Chord
Radius and Web
Clean1
(b)-BMS 5-45, CLASS BSealant, Integral Fuel
Tank
Apply2
(a) Clean the rear spar upper chord radius and the upper edge of the rear spar web between Left Buttock
Line (LBL) 70.50 and Right Buttock Line (RBL) 70.50. Refer to SOPM 20-30-93 as an accepted procedure.
(b) Apply a fillet seal common to the upper edge of the rear spar web and radius of the rear spar upper chord
LBL 70.50 to RBL 70.50. Refer to 727 AMM 51-31-00 or SOPM 20-50-19 as an accepted procedure.
FIGURE 6: WINGS - WING CENTER SECTION - REAR SPAR UPPER CHORD - INTERNAL FUEL TANK
SEALANT APPLICATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: March 08, 2012
727-57-0187
49 of 49
BOEING SERVICE BULLETIN 727-57-0187

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
