# Boeing Service Bulletin 737-25-1707: SB-737-25-1707-02--

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2021-0504; AD 2021-26-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 737-25-1707](https://openairdocs.org/service-documents/boeing/sb-737-25-1707.md)
- Title as filed: SB-737-25-1707-02--
- Pages: 87
- PDF: https://openairdocs.org/files/sha256/a7/f5/a7f5f6ff30d2575e6890ce6ac5bf4423a16f90da614181344d049a63077e7393
- Page: https://openairdocs.org/service-documents/boeing/sb-737-25-1707/file/a7f5f6ff30d2

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-25-1707
Original Issue: September 24, 2015
Revision 2: July 27, 2020
ATA System: 2523
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Service Units - Passenger
Service Unit (PSU) and Life Vest Panel Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2015 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
1 of 87
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
2 of 87
BOEING SERVICE BULLETIN 737-25-1707
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 31
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 40
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 43
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
[Group 1-2, 5, 7-8, Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT [Group 2,
Configuration 1; Group 5; Group 8, Configuration 1] . . . . . . . . . . . . . . . . . . . . . 54
FIGURE 3: PASSENGER SERVICE UNIT - LANYARD ASSEMBLY MEASUREMENT [Group 1-2,
Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group 6, Configuration
1; Group 7-8, Configuration 2; Group 9, Configuration 1] . . . . . . . . . . . . . . . . . . 60
FIGURE 4: LIFE VEST PANEL - LANYARD ASSEMBLY MEASUREMENT [Group 2, Configuration 2; Group
4, Configuration 1; Group 8, Configuration 2; Group 9] . . . . . . . . . . . . . . . . . . . . 62
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
3 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 4

FIGURE 5: PASSENGER SERVICE UNIT - IDENTIFICATION [Group 1-2, Configuration 2; Group 3-4,
Configuration 1; Group 5, Configuration 2; Group 6, Configuration 1; Group 7-8, Configuration
2; Group 9, Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
FIGURE 6: PASSENGER SERVICE UNIT - LANYARD ASSEMBLY REPLACEMENT [Group 1-2,
Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group 6, Configuration
1; Group 7-8, Configuration 2; Group 9, Configuration 1] . . . . . . . . . . . . . . . . . . 66
FIGURE 7: LIFE VEST PANEL - IDENTIFICATION [Group 2, Configuration 2; Group 4, Configuration 1;
Group 8, Configuration 2; Group 9] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
FIGURE 8: LIFE VEST PANEL - LANYARD ASSEMBLY REPLACEMENT [Group 2, Configuration 2; Group
4, Configuration 1; Group 8, Configuration 2; Group 9] . . . . . . . . . . . . . . . . . . . . 71
FIGURE 9: PASSENGER SERVICE UNIT - PART NUMBER INSPECTION AND REIDENTIFICATION
[Group 7, Configuration 2-3; Group 8, Configuration 2-3] . . . . . . . . . . . . . . . . . . 74
APPENDIX A: PASSENGER SERVICE UNIT (PSU) - REIDENTIFICATION . . . . . . . . . . . . . . . . 76
APPENDIX B: LIFE VEST PANEL - REIDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . 85
APPENDIX C: PART DEMAND INTENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
APPENDIX D: KITS 002A0002-451 AND 002A0002-452 - CHECK . . . . . . . . . . . . . . . . . . . . . 87
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
4 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 5

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-25-1707Original Issue: September 24, 2015
Revision 2: July 27, 2020
ATA System: 2523
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Service Units - Passenger
Service Unit (PSU) and Life Vest Panel Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2019-03-26 is related to this service bulletin.
Airplane variable numbers YG701, YG711, YM591 thru YM593 and YM594 thru YM599 were added to Group
1 of this service bulletin effectivity.
Airplane variable numbers YA811 thru YA814 were moved from Group 1 to new Group 5 of this service bulletin
effectivity.
Airplane variable numbers YG515 thru YG517, YG721, YG722 and YK478 were added to Group 3 of this service
bulletin effectivity.
Airplane variable numbers YF671 thru YF674, YF676 thru YF685, YF691, YF693 thru YF695, YQ519 and YQ520
were moved from Group 3 to new Group 9 of this service bulletin effectivity.
Airplane variable numbers YF669 and YF670, YF675, YF692, YQ356 thru YQ363, YQ364, YQ365 and YQ516
thru YQ518 were added to Group 4 of this service bulletin effectivity.
Airplane variable numbers YQ351 thru YQ355 and YQ371 were moved from Group 4 to new Group 6 of this
service bulletin effectivity.
Airplane variable numbers YA255, YA256, YA645, YA656, YB884, YB885, YG112, YG113, YK721 thru YK740,
YK796, YK797, YL271, YL272, YL301, YL303, YL461 thru YL470, YM571, YM572 and YN071 thru YN078,
were moved from Group 1 to new Group 7 of this service bulletin effectivity.
Airplane variable numbers YN091, YN092 and YN121 were moved from Group 2 to new Group 8 of this service
bulletin effectivity.
Effects of this Revision on airplanes on which the Original Issue or Revision 1 was previously done:
See Paragraph 1.D., Description for more information.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
5 of 87

### Page 6

REASON FOR REVISION
This revision is sent to add and move airplanes to new groups to agree with their Passenger Service Unit (PSU)
and Life Vest Panel configurations. This revision is also sent to add reidentification part numbers related to those
PSUs that were changed by Boeing Service Bulletin 737-35-1107.
These sections were changed:
1. Summary Background, added reference in planning table.
2. Summary Action, changed applicability, added information for Groups 5, 6, 7, 8 and 9.
3. Summary Compliance, removed Notice of Proposed Rule Making, added Airworthiness Directive
information.
4. Summary Illustration, changed applicability, added information for Groups 5, 6, 7, 8 and 9.
5. Paragraph 1.A.1., Airplanes, added and moved airplanes to new groups, changed configuration
descriptions, added configurations, added new Groups 5, 6, 7, 8 and 9.
6. Paragraph 1.C., Reason, added Revision 2 information.
7. Paragraph 1.D., Description, changed applicability, added information for Groups 5, 6, 7, 8 and 9,
added Revision 2 information, added maintenance zones for Groups 5, 6, 7, 8 and 9.
8. Paragraph 1.E., Compliance, removed Notice of Proposed Rule Making, added Airworthiness Directive
information.
9. Paragraph 1.F., Approval, added Alternative Method of Compliance (AMOC) information.
10. Paragraph 1.G., Manpower, changed applicability, added estimates for Groups 5, 6, 7, 8 and 9, corrected
and added tasks in applicable tables for 'Part 1 - Airplane Work: Life Vest Panel', changed and added
information for 'Part 2 - Component Work: PSU'.
11. Paragraph 1.H., Weight and Balance Changes, changed applicability.
12. Paragraph 1.J.1., Existing Data, removed Notice of Proposed Rule Making, added Airworthiness
Directive, added Boeing Service Bulletin reference.
13. Paragraph 1.K., Publications Affected, changed the information.
14. Paragraph 2.A., Material - Price and Availability, changed applicability, changed the information, added
information for Group 7 and 8 Configuration 3, changed footnote (b).
15. Paragraph 2.B., Industry Support Information, changed applicability.
16. Paragraph 2.C.1., Kits/Parts, changed applicability.
17. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, changed applicability, added availability
information, divided information to show correct parts and materials for PSUs and Life Vest Panels.
18. Paragraph 2.C.3., Parts Modified and Reidentified, added part numbers.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
6 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 7

19. Paragraph 2.D., Parts Necessary to Change Spares, added part, changed footnotes to better qualify
parts usage.
20. Paragraph 3.B., Work Instructions, changed applicability, added instructions in Part 1 and Part 2.
21. Figure 1, changed applicability, changed step 7, added information, changed illustration locator and
detail PSU view.
22. Figure 2, changed applicability, changed step 12, added information, changed illustration locator.
23. Figure 3 and Figure 4, changed applicability, changed illustration locator.
24. Figure 5 and Figure 7, changed applicability, changed step 1, added information, changed illustration
locator.
25. Figure 6, changed applicability, changed step 3, added information, changed illustration locator.
26. Figure 8, changed applicability, changed step 6, added information, changed illustration locator.
27. Figure 9, added.
28. Appendix A, added PSU reidentification part numbers.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
September 24, 2015Original Issue:
May 18, 2018Revision 1:
July 27, 2020Revision 2:
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
7 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
8 of 87
BOEING SERVICE BULLETIN 737-25-1707
BLANK PAGE

### Page 9

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-25-1707Original Issue: September 24, 2015
Revision 2: July 27, 2020
ATA System: 2523
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Service Units - Passenger
Service Unit (PSU) and Life Vest Panel Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions to add a secondary method of retention to the Life Vest Panels and the
Passenger Service Units (PSUs), to prevent them from detachment during an occurrence that is more than
emergency load requirements. If this service bulletin is not done, PSUs or Life Vest Panels can become detached
when emergency load requirements are exceeded which could lead to passenger injuries and impede passenger
and crew egress during evacuation.
In three survivable 737NG hull loss accidents that are thought to have exceeded design loads, PSUs and Life
Vest Panels became detached from supporting structure in the airplane. The design of these PSUs and Life
Vest Panels meet the applicable emergency load requirements of Federal Aviation Regulation (FAR) 25.561.
However, to enhance the safety of the airplane, Boeing has changed the design to add a secondary retention
for these PSUs and Life Vest Panels to prevent detachment and falling into the cabin during a survivable hull
loss accident. The design of these existing PSUs and Life Vest Panels have a single lanyard assembly for
maintenance purposes on the inboard edge of the panel.
Accomplishment of this service bulletin installs lanyard assemblies for retention support on the PSUs and Life
Vest Panels to decrease the risk of injury to passengers and evacuation hindrance during survivable hull loss
accidents.
Since the release of the Original Issue of this service bulletin, Boeing has found that the torsion spring of lanyard
assembly, part number 417A3003-9, could be manufactured incorrectly. The incorrect manufacture could have
resulted in the distance between the hooks of the torsion spring to be less than necessary. A torsion spring in
this condition causes it to not engage correctly when it is attached in the PSU rail. Boeing has worked with the
supplier who has corrected the problem to subsequently supply correctly manufactured lanyard assemblies. As
a solution to the problem where incorrectly manufactured lanyard assemblies could be installed on PSUs and
Life Vest Panels changed by this service bulletin at the Original Issue or that got installed on airplanes before
delivery, Boeing has included instructions in this service bulletin to make sure those PSUs and Life Vest Panels
have correctly manufactured lanyard assemblies.
Boeing Fleet Team Digest (FTD) 737NG FTD 25-14002 is related to this service bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
9 of 87

### Page 10

Boeing Service Related Problem (SRP) 737NG-SRP-25-0342 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION (PRR 39004)
Group 1, 7, Configuration 1:
Lower each PSU. Add and replace lanyard assemblies. Close each PSU.
Group 2, 5, 8, Configuration 1:
Lower each PSU and Life Vest Panel. Add and replace lanyard assemblies. Close each PSU and Life Vest
Panel.
Group 1, Configuration 2; Group 3, 6, Configuration 1:
Lower each PSU. Measure the distance between the hooks of the torsion spring of the lanyard assembly. Do
corrective actions or identify each lanyard assembly is serviceable. Close each PSU.
Group 2, Configuration 2; Group 4, 9, Configuration 1:
Lower each PSU and Life Vest Panel. Measure the distance between the hooks of the torsion spring of the
lanyard assembly. Do corrective actions or identify each lanyard assembly is serviceable. Close each PSU and
Life Vest Panel.
Group 9, Configuration 2:
Lower each Life Vest Panel. Measure the distance between the hooks of the torsion spring of the lanyard
assembly. Do corrective actions or identify each lanyard assembly is serviceable. Close each Life Vest Panel.
Group 5, Configuration 2:
Lower each PSU. Measure the distance between the hooks of the torsion spring of the lanyard assembly. Do
corrective actions or identify each lanyard assembly is serviceable. Close each PSU. Lower each Life Vest
Panel. Add and replace lanyard assemblies. Close each Life Vest Panel.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
10 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 11

Group 5, Configuration 3:
Lower each Life Vest Panel. Add and replace lanyard assemblies. Close each Life Vest Panel.
Group 7-8, Configuration 2:
Lower each PSU. Inspect each PSU to find if it has the correct reidentification part number, and change the
reidentification part number on the PSU(s) if an incorrect one is found. Measure the distance between the hooks
of the torsion spring of the lanyard assembly. Do corrective actions or identify each lanyard assembly is
serviceable. Close each PSU.
Group 7-8, Configuration 3:
Lower each PSU. Inspect each PSU to find if it has the correct reidentification part number, and change the
reidentification part number on the PSU(s) if an incorrect one is found. Close each PSU.
Group 1-2, Configuration 3; Group 3-4, 6, Configuration 2:
No further action required.
EFFECTIVITY
737-600/700/700C/800/900/900ER airplanes without a Boeing Sky Interior (BSI). Refer to Paragraph 1.A.1.,
Airplanes, for the list of affected airplane(s).
Refer to Paragraph 1.A.2., Spares Affected, for the list of affected components.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2019-03-26 is related to this service bulletin.
The effective date of AD 2019-03-26 is April 8, 2019.
Boeing recommends that the inspection, change and/or repair given in this service bulletin be done within 60
months after the effective date of AD 2019-03-26.
INDUSTRY SUPPORT INFORMATION
Refer to Paragraph 2.B., Industry Support Information.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Operators are encouraged to complete the survey provided in APPENDIX C of this service bulletin to help Boeing
predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
11 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 12 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each Passenger Service Unit.
Step  Task  Name  Identification  Qty  More Data
1  Measure  DISTANCE  1  Measure the dis-
tance between the
hooks of the torsion
spring.
FIGURE 3: PASSENGER SERVICE UNIT - LANYARD ASSEMBLY MEASUREMENT
(SHEET 2 OF 2)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  737-25-1707
Copyright © Unpublished
Work - See page 1 for details.  61 of 87

### Page 13

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-25-1707
Original Issue: September 24, 2015
Revision 2: July 27, 2020
ATA System: 2523
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Service Units - Passenger
Service Unit (PSU) and Life Vest Panel Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D6-19567 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This bulletin is applicable to 737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
Airplane(s), line number(s) 1-100, 102-110, 112-125, 127-130, 132-142, 144-145, 147-149, 151-157,
159-166, 168-178, 180-188, 190-196, 198-205, 207-216, 218-224, 226-233, 235-240, 242-243,
245-250, 252-264, 266-279, 281-300, 302-311, 313-322, 324-335, 337-347, 349-355, 357-376,
378-383, 385-396, 398-400, 402-407, 409-414, 416-422, 424-431, 433-444, 446-450, 452-455,
457-480, 482-490, 492-515, 517-529, 531-544, 546-553, 555-568, 570-585, 587-601, 603-612,
614-622, 624-641, 643-683, 685-737, 739-746, 748-778, 780-786, 788-825, 827-835, 837-852,
854-860, 862-881, 883-888, 890-911, 913-925, 927-939, 941-952, 954-968, 970-978, 980-987,
989-995, 997-1036, 1038-1059, 1061-1074, 1076-1088, 1090-1110, 1112-1123, 1125-1188,
1190-1195, 1197-1203, 1205-1210, 1212-1216, 1218-1222, 1224-1231, 1233-1244, 1246-1601,
1603-1613, 1615-1745, 1747-1757, 1759-1784, 1786-1802, 1804-1809, 1811-1824, 1826-1838,
1840-1858, 1860-1864, 1866-1884, 1886-1933, 1935-1965, 1967-1978, 1980-1990, 1992-2028,
2030-2046, 2048-2067, 2069-2079, 2081-2106, 2108-2195, 2197-2210, 2212-2339, 2341-2474,
2476-2594, 2596-2598, 2600-2663, 2665-2695, 2697-2721, 2723-2724, 2726-2751, 2753-2813,
2815-2821, 2823-2868, 2870-2930, 2932-2964, 2966-2996, 2998-3023, 3025-3032, 3034-3068,
3070, 3072-3127, 3129-3188, 3190-3207, 3209-3218, 3220-3318, 3320-3323, 3325-3328,
3330-3355, 3357-3368, 3370-3390, 3392-3398, 3400-3420, 3422-3424, 3427-3451, 3453-3457,
3459, 3462-3463, 3465-3481, 3483-3484, 3487, 3489, 3491-3494, 3496, 3498-3506, 3508,
3510-3516, 3518-3520, 3523-3529, 3531, 3533-3536, 3538-3539, 3541-3544, 3546-3547,
3550-3552, 3555-3556, 3558-3561, 3563-3564, 3566, 3568-3571, 3573-3575, 3578-3581,
3584-3585, 3587, 3589-3590, 3593-3594, 3596-3600, 3602-3607, 3609-3610, 3613-3614,
3616-3617, 3621-3622, 3624-3626, 3628-3629, 3632, 3635, 3637-3638, 3643-3644, 3647-3649,
3652, 3654, 3656-3658, 3661-3662, 3672, 3674-3677, 3679, 3682-3684, 3687, 3690-3692, 3696,
3698, 3703, 3705, 3708, 3712-3716, 3719, 3724, 3726, 3728, 3736, 3742-3744, 3747, 3754-3755,
3759, 3762, 3767, 3769-3770, 3772, 3774, 3778-3780, 3786-3789, 3791, 3795, 3797, 3800, 3804,
3811, 3814, 3819, 3821-3822, 3828-3830, 3834, 3841-3842, 3860, 3863, 3869, 3872, 3874, 3882,
3884, 3886, 3905-3906, 3908, 3920, 3926, 3928, 3931-3932, 3938, 3945, 3953, 3958, 3974, 3983,
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
13 of 87

### Page 14

3986, 3992, 4002-4003, 4011, 4017, 4048, 4062, 4072, 4074, 4087, 4091, 4095, 4097, 4101,
4104, 4122, 4136, 4151-4152, 4166, 4169, 4174, 4177, 4190, 4204, 4211, 4220, 4227-4228, 4240,
4249, 4261, 4268, 4280, 4282, 4293, 4303, 4313, 4321, 4334, 4349, 4364, 4376-4377, 4393,
4426, 4429, 4458, 4469, 4545, 4561, 4586, 4608, 4621, 4634, 4641, 4653, 4702, 4770, 4788,
4851-4852, 4922, 4953, 4970, 4985, 5000, 5025, 5072, 5079, 5090, 5099, 5101, 5103, 5106,
5111, 5124, 5147, 5158, 5188, 5216, 5238, 5248, 5257, 5289, 5296, 5301, 5316, 5330, 5341,
5344, 5352, 5367, 5374, 5393, 5401-5402, 5429, 5434, 5444, 5448, 5474, 5476, 5511, 5562,
5568, 5605, 5609, 5618, 5625, 5638, 5642, 5650, 5653, 5660, 5665, 5677, 5681, 5683, 5705,
5717, 5724, 5766, 5785, 5836, 5862, 5982, 6060, 6099, 6187, 6203, 7477, 7587 in 9 Group(s).
Where the effectivity is presented with hyphens between line numbers, the airplane applicability
means "through" and "inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below. Refer
to PRR 39004 for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
Airplanes without a Boeing Sky Interior, equipped with Passenger
Service Units (PSUs).
-1
Airplanes that have not done the Original Issue or Revision 1 of this
Service Bulletin.
1
Airplanes that have done the Original Issue but have not done
Revision 1 of this Service Bulletin.
2
Airplanes that have done Revision 1 of this Service Bulletin.3
Airplanes without a Boeing Sky Interior, equipped with PSUs and
Life Vest Panels.
-2
Airplanes that have not done the Original Issue or Revision 1 of this
Service Bulletin.
1
Airplanes that have done the Original Issue but have not done
Revision 1 of this Service Bulletin.
2
Airplanes that have done Revision 1 of this Service Bulletin.3
Airplanes without a Boeing Sky Interior, equipped with PSUs, that
had lanyard assemblies installed in production
-3
Airplanes that have not done Revision 1 of this Service Bulletin.1
Airplanes that have done Revision 1 of this Service Bulletin.2
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
14 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 15

DESCRIPTIONCONFIGURATIONGROUP
Airplanes without a Boeing Sky Interior, equipped with PSUs and
Life Vest Panels, that had lanyard assemblies installed in production.
-4
Airplanes that have not done Revision 1 of this Service Bulletin.1
Airplanes that have done Revision 1 of this Service Bulletin.2
Airplanes without a Boeing Sky Interior, equipped with PSUs and
Life Vest Panels, that were included in Group 1 of the effectivity of
this Service Bulletin at the Original Issue and Revision 1.
-5
Airplanes that have not done the Original Issue or Revision 1 of this
Service Bulletin.
1
Airplanes that have done the Original Issue but have not done
Revision 1 of this Service Bulletin.
2
Airplanes that have done Revision 1 of this Service Bulletin.3
Airplanes without a Boeing Sky Interior, equipped with PSUs, that
had lanyard assemblies installed in production, that were included
in Group 4 of the effectivity of this Service Bulletin at Revision 1.
-6
Airplanes that have not done Revision 1 of this Service Bulletin.1
Airplanes that have done Revision 1 of this Service Bulletin.2
Airplanes without a Boeing Sky Interior, equipped with PSUs, that
were included in Group 1 of the effectivity of this Service Bulletin at
the Original Issue and Revision 1, and that are also included in the
effectivity of Boeing Service Bulletin 737-35-1107.
-7
Airplanes that have not done the Original Issue or Revision 1 of this
service bulletin.
1
Airplanes that have done the Original Issue but have not done
Revision 1 of this service bulletin.
2
Airplanes that have done Revision 1 of this service bulletin.3
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
15 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 16

DESCRIPTIONCONFIGURATIONGROUP
Airplanes without a Boeing Sky Interior, equipped with PSUs and
Life Vest Panels, that were included in Group 2 of the effectivity of
this Service Bulletin at the Original Issue and Revision 1, and that
are also included in the effectivity of Boeing Service Bulletin
737-35-1107.
-8
Airplanes that have not done the Original Issue or Revision 1 of this
service bulletin.
1
Airplanes that have done the Original Issue but have not done
Revision 1 of this service bulletin.
2
Airplanes that have done Revision 1 of this service bulletin.3
Airplanes without a Boeing Sky Interior, equipped with PSUs and
Life Vest Panels, that had lanyard assemblies installed in production,
and that were included in Group 3 of the effectivity of this Service
Bulletin at Revision 1.
-9
Airplanes that have not done Revision 1 of this Service Bulletin.1
Airplanes that have done Revision 1 of this Service Bulletin.2
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
GroupVariable Number
1YA001 - YA099
1YA101 - YA199
2YA201 - YA211
1YA221
1YA231 - YA242
1YA251 - YA254
7YA255 - YA256
2YA271 - YA272
1YA291
1YA301 - YA302
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
GroupVariable Number
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
7YA645
GroupVariable Number
1YA646 - YA650
7YA656
1YA657 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
2YA721 - YA722
1YA731 - YA734
1YA751 - YA756
1YA801 - YA803
1YA809
5YA811 - YA814
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
16 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 17

GroupVariable Number
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
2YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB636
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB883
7YB884 - YB885
1YB886 - YB893
1YB901 - YB903
1YB911
GroupVariable Number
1YB961 - YB974
2YB975
2YB981
1YB986 - YB989
2YB990 - YB998
1YC001 - YC030
1YC051 - YC084
1YC091 - YC095
1YC101 - YC104
1YC111 - YC113
1YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC179
1YC186 - YC190
1YC201 - YC203
1YC206 - YC207
1YC301 - YC305
1YC321 - YC387
2YC391 - YC393
1YC394
1YC396
1YC401 - YC408
2YC409 - YC415
1YC416 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC439
1YC441 - YC448
1YC451 - YC455
GroupVariable Number
1YC459
1YC461 - YC467
1YC471 - YC499
1YC501 - YC526
1YC571 - YC583
1YC587 - YC589
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
1YC701 - YC715
1YC720 - YC725
1YC727 - YC752
1YC761 - YC770
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
17 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 18

GroupVariable Number
1YD256 - YD257
1YD261
1YD301 - YD334
2YD391
1YD481 - YD485
1YD491 - YD499
1YD501 - YD512
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
1YD591 - YD595
1YD601 - YD612
1YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
1YF001 - YF011
1YF021 - YF049
1YF051 - YF080
1YF086 - YF087
1YF106 - YF107
1YF111 - YF114
1YF116 - YF119
1YF121 - YF132
1YF176 - YF178
1YF191 - YF192
GroupVariable Number
1YF201 - YF276
1YF401 - YF402
1YF431 - YF432
1YF436 - YF437
1YF441 - YF442
1YF451 - YF460
2YF501 - YF599
2YF601 - YF668
4YF669 - YF670
9YF671 - YF674
4YF675
9YF676 - YF685
9YF691
4YF692
9YF693 - YF695
1YF701 - YF707
1YF801 - YF805
2YF831 - YF832
2YF836 - YF838
1YF871 - YF872
1YF901 - YF905
1YF921 - YF928
1YF951 - YF954
1YG101 - YG104
7YG112 - YG113
1YG114
1YG251 - YG252
1YG501 - YG514
3YG515 - YG517
1YG601 - YG602
1YG701
1YG711
3YG721 - YG722
GroupVariable Number
1YH001 - YH012
1YH031 - YH055
1YH071 - YH080
1YH101 - YH132
1YH201 - YH202
1YH206 - YH207
1YH321 - YH322
1YJ001 - YJ013
1YJ021
1YJ471 - YJ480
1YJ501 - YJ517
1YJ531 - YJ579
1YJ591 - YJ599
1YJ631 - YJ632
1YJ671 - YJ694
1YJ801 - YJ845
2YJ846 - YJ860
1YJ861 - YJ867
1YJ871 - YJ880
1YJ901 - YJ904
1YJ908 - YJ929
1YJ931 - YJ937
1YJ941 - YJ956
1YJ961
1YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
1YK131 - YK133
1YK136 - YK139
1YK141 - YK142
1YK146 - YK148
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
18 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 19

GroupVariable Number
1YK151 - YK154
1YK161 - YK167
1YK171
1YK176 - YK177
1YK186
1YK191
1YK196
1YK201 - YK202
1YK301 - YK314
1YK321 - YK340
1YK361 - YK378
1YK401 - YK406
1YK426 - YK427
1YK431 - YK450
1YK456 - YK467
1YK471 - YK473
1YK476
3YK478
1YK480 - YK487
2YK491 - YK493
1YK495 - YK496
2YK497 - YK499
1YK511 - YK516
1YK521 - YK530
1YK551 - YK571
1YK576 - YK577
1YK580 - YK585
1YK601 - YK602
1YK606 - YK607
1YK611 - YK616
1YK621 - YK634
1YK641 - YK644
1YK651 - YK665
GroupVariable Number
1YK671 - YK672
1YK676 - YK677
1YK681 - YK686
1YK691
1YK695 - YK699
1YK701 - YK713
1YK716 - YK719
7YK721 - YK740
1YK741
1YK751 - YK770
1YK776 - YK778
1YK781 - YK785
1YK791 - YK792
7YK796 - YK797
2YK801 - YK899
1YK901 - YK912
1YK918 - YK919
1YK921 - YK929
1YK941 - YK999
1YL001 - YL005
1YL011 - YL016
1YL021 - YL024
1YL051 - YL052
1YL056 - YL057
1YL061
1YL066 - YL069
1YL076 - YL077
1YL101 - YL137
1YL201 - YL237
1YL241 - YL242
7YL271 - YL272
1YL281 - YL284
7YL301
GroupVariable Number
1YL302
7YL303
1YL311 - YL314
1YL316 - YL321
1YL351 - YL353
2YL371 - YL374
1YL401
1YL421 - YL429
1YL431 - YL444
7YL461 - YL470
1YL471 - YL478
1YL501 - YL509
1YL531 - YL534
1YL541 - YL551
1YL561 - YL579
1YL591 - YL598
1YL601 - YL606
1YL611 - YL612
1YL616 - YL617
1YL621
1YL626
1YL631 - YL634
1YL636 - YL637
1YL661 - YL664
1YL676 - YL691
1YL696 - YL697
1YL701 - YL707
2YL731
1YL751 - YL752
1YL756 - YL757
1YL761 - YL780
1YL796 - YL797
1YL801 - YL815
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
19 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 20

GroupVariable Number
1YL901 - YL910
1YL921 - YL940
1YL951 - YL968
1YM101 - YM103
1YM201 - YM244
1YM251 - YM299
1YM301 - YM399
1YM401 - YM415
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
7YM571 - YM572
1YM581 - YM582
1YM591 - YM599
1YM631 - YM634
1YM641 - YM652
1YM671 - YM674
1YM691 - YM699
GroupVariable Number
1YM701 - YM710
1YM761 - YM765
1YM771 - YM779
1YN001 - YN016
1YN021 - YN024
1YN061
7YN071 - YN078
1YN079 - YN082
8YN091 - YN092
1YN101 - YN112
8YN121
1YN126
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
1YN261
2YQ001 - YQ003
1YQ011 - YQ021
1YQ026 - YQ029
1YQ036 - YQ045
1YQ201 - YQ207
GroupVariable Number
1YQ231
1YQ241 - YQ251
1YQ281 - YQ284
1YQ291 - YQ296
1YQ301 - YQ302
1YQ321 - YQ324
1YQ331 - YQ334
1YQ346 - YQ347
6YQ351 - YQ355
4YQ356 - YQ365
6YQ371
1YQ401 - YQ403
1YQ451 - YQ454
1YQ456
1YQ461
1YQ471
2YQ501 - YQ515
4YQ516 - YQ518
9YQ519 - YQ520
--
--
2. Spares Affected
Examine your spares supply for the parts identified in APPENDIX A and APPENDIX B. If any parts
or components are found, refer to Paragraph 3.B., Work Instructions, Part 2 - Component Work,
for the recommended action.
B. Concurrent Requirements
None.
C. Reason
This service bulletin gives instructions to add a secondary method of retention to the Life Vest Panels
and the Passenger Service Units (PSUs), to prevent them from detachment during an occurrence that
is more than emergency load requirements. If this service bulletin is not done, PSUs or Life Vest Panels
can become detached when emergency load requirements are exceeded which could lead to passenger
injuries and impede passenger and crew egress during evacuation.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
20 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 21

In three survivable 737NG hull loss accidents that are thought to have exceeded design loads, PSUs
and Life Vest Panels became detached from supporting structure in the airplane. The design of these
PSUs and Life Vest Panels meet the applicable emergency load requirements of Federal Aviation
Regulation (FAR) 25.561. However, to enhance the safety of the airplane, Boeing has changed the
design to add a secondary retention for these PSUs and Life Vest Panels to prevent detachment and
falling into the cabin during a survivable hull loss accident. The design of these existing PSUs and Life
Vest Panels have a single lanyard assembly for maintenance purposes on the inboard edge of the
panel.
Accomplishment of this service bulletin installs lanyard assemblies for retention support on the PSUs
and Life Vest Panels to decrease the risk of injury to passengers and evacuation hindrance during
survivable hull loss accidents.
Since the release of the Original Issue of this service bulletin, Boeing has found that the torsion spring
of lanyard assembly, part number 417A3003-9, could be manufactured incorrectly. The incorrect
manufacture could have resulted in the distance between the hooks of the torsion spring to be less
than necessary. A torsion spring in this condition causes it to not engage correctly when it is attached
in the PSU rail. Boeing has worked with the supplier who has corrected the problem to subsequently
supply correctly manufactured lanyard assemblies. As a solution to the problem where incorrectly
manufactured lanyard assemblies could be installed on PSUs and Life Vest Panels changed by this
service bulletin at the Original Issue or that got installed on airplanes before delivery, Boeing has
included instructions in this service bulletin to make sure those PSUs and Life Vest Panels have correctly
manufactured lanyard assemblies.
Boeing Fleet Team Digest (FTD) 737NG FTD 25-14002 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-SRP-25-0342 is related to this service bulletin.
Revision 1 was sent to add airplanes to the effectivity of this service bulletin and to better describe and
define the addition and replacement of the lanyard assemblies on the PSUs and Life Vest Panels. Also,
Revision 1 adds instructions to make sure that a lanyard assembly, part number 417A3003-9, installed
by the Original Issue of this service bulletin, installed on a PSU and Life Vest Panel during production,
or held in kits 002A0002-451 and -452 that are to be installed, was manufactured to have the correct
distance between the hooks of its torsion spring. New kits 002A0002-500, -501 and -502 are available
in this revision, which, if ordered, supply a correctly manufactured lanyard assembly. Also, instructions
to attach the lanyard assembly torsion spring to the nearest larger hole in the PSU rail, are described
more clearly in this revision.
The data given in Information Notice 737-25-1707 IN01 and IN 02 is included in Revision 1.
Revision 2 is sent to add and move airplanes to new groups to agree with their Passenger Service Unit
(PSU) and Life Vest Panel configurations. This revision is also sent to add reidentification part numbers
related to those PSUs that were changed by Boeing Service Bulletin 737-35-1107.
D. Description
Group 1, 7, Configuration 1:
Lower each PSU. Add and replace lanyard assemblies. Close each PSU.
Group 2, 5, 8, Configuration 1:
Lower each PSU and Life Vest Panel. Add and replace lanyard assemblies. Close each PSU and Life
Vest Panel.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
21 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 22

Group 1, Configuration 2; Group 3, 6, Configuration 1:
Lower each PSU. Measure the distance between the hooks of the torsion spring of the lanyard assembly.
Do corrective actions or identify each lanyard assembly is serviceable. Close each PSU.
Group 2, Configuration 2; Group 4, 9, Configuration 1:
Lower each PSU and Life Vest Panel. Measure the distance between the hooks of the torsion spring
of the lanyard assembly. Do corrective actions or identify each lanyard assembly is serviceable. Close
each PSU and Life Vest Panel.
Group 9, Configuration 2:
Lower each Life Vest Panel. Measure the distance between the hooks of the torsion spring of the
lanyard assembly. Do corrective actions or identify each lanyard assembly is serviceable. Close each
Life Vest Panel.
Group 5, Configuration 2:
Lower each PSU. Measure the distance between the hooks of the torsion spring of the lanyard assembly.
Do corrective actions or identify each lanyard assembly is serviceable. Close each PSU. Lower each
Life Vest Panel. Add and replace lanyard assemblies. Close each Life Vest Panel.
Group 5, Configuration 3:
Lower each Life Vest Panel. Add and replace lanyard assemblies. Close each Life Vest Panel.
Group 7-8, Configuration 2:
Lower each PSU. Inspect each PSU to find if it has the correct reidentification part number, and change
the reidentification part number on the PSU(s) if an incorrect one is found. Measure the distance
between the hooks of the torsion spring of the lanyard assembly. Do corrective actions or identify each
lanyard assembly is serviceable. Close each PSU.
Group 7-8, Configuration 3:
Lower each PSU. Inspect each PSU to find if it has the correct reidentification part number, and change
the reidentification part number on the PSU(s) if an incorrect one is found. Close each PSU.
Group 1-2, Configuration 3; Group 3-4, 6, Configuration 2:
No further action required.
Effects of Revision 2 on airplanes on which the Original Issue or Revision 1 was previously done:
ActionConditionGroup
Measure the distance between the hooks of the torsion spring
of each lanyard assembly, part number 417A3003-9. If the
measured distance is less than specified, replace each lan-
yard assembly and identify each PSU and each replaced
lanyard assembly. If the measured distance is equal to or
greater than specified, identify each PSU and each lanyard
assembly.
Airplanes that have added and
replaced lanyard assemblies on
PSUs.
Group 1, Con-
figuration 2
None.Airplanes that have added and
replaced lanyard assemblies on
PSUs, and that have made sure
that the lanyards installed on the
PSUs were serviceable.
Group 1, Con-
figuration 3
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
22 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 23

ActionConditionGroup
Measure the distance between the hooks of the torsion spring
of each lanyard assembly, part number 417A3003-9. If the
measured distance is less than specified, replace each lan-
yard assembly and identify each PSU and Life Vest Panel,
and each replaced lanyard assembly. If the measured dis-
tance is equal to or greater than specified, identify each PSU
and Life Vest Panel and each lanyard assembly.
Airplanes that have added and
replaced lanyard assemblies on
PSUs and Life Vest Panels.
Group 2, Con-
figuration 2
None.Airplanes that have added and
replaced lanyard assemblies on
PSUs and Life Vest Panels, and
that have made sure that the
lanyards installed on the PSUs
and Life Vest Panels were ser-
viceable.
Group 2, Con-
figuration 3
None.Airplanes that have made sure
that the lanyards installed on the
PSUs in production were ser-
viceable.
Group 3, Con-
figuration 2;
Group 6, Con-
figuration 2
None.Airplanes that have made sure
that the lanyards installed on the
PSUs and Life Vest Panels in
production were serviceable.
Group 4, Con-
figuration 2
Action 1: Measure the distance between the hooks of the
torsion spring of each lanyard assembly, part number
417A3003-9. If the measured distance is less than specified,
replace each lanyard assembly and identify each PSU and
each replaced lanyard assembly. If the measured distance
is equal to or greater than specified, identify each PSU and
each lanyard assembly.
Airplanes that have added and
replaced lanyard assemblies on
PSUs, but not on Life Vest
Panels.
Group 5, Con-
figuration 2
Action 2: Add and replace lanyard assemblies on Life Vest
Panels.
Add and replace lanyard assemblies on Life Vest Panels.Airplanes that have added and
replaced lanyard assemblies on
PSUs, and that have made sure
that the lanyards installed on the
PSUs were serviceable.
Group 5, Con-
figuration 3
Action 1: Inspect each PSU to find if it has the correct reiden-
tification part number, change the reidentification part number
on the PSU(s) if an incorrect one is found.
Airplanes that have added and
replaced lanyard assemblies on
PSUs.
Group 7, Con-
figuration 2
Action 2: Measure the distance between the hooks of the
torsion spring of each lanyard assembly, part number
417A3003-9. If the measured distance is less than specified,
replace each lanyard assembly and identify each PSU and
each replaced lanyard assembly. If the measured distance
is equal to or greater than specified, identify each PSU and
each lanyard assembly.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
23 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 24

ActionConditionGroup
Inspect each PSU to find if it has the correct reidentification
part number, change the reidentification part number on the
PSU(s) if an incorrect one is found.
Airplanes that have added and
replaced lanyard assemblies on
PSUs, and that have made sure
that the lanyards installed on the
PSUs were serviceable.
Group 7, Con-
figuration 3
Action 1: Inspect each PSU to find if it has the correct reiden-
tification part number, and change the reidentification part
number on the PSU(s) if an incorrect one is found.
Airplanes that have added and
replaced lanyard assemblies on
PSUs and Life Vest Panels.
Group 8, Con-
figuration 2
Action 2: Measure the distance between the hooks of the
torsion spring of each lanyard assembly, part number
417A3003-9. If the measured distance is less than specified,
replace each lanyard assembly and identify each PSU and
Life Vest Panel, and each replaced lanyard assembly. If the
measured distance is equal to or greater than specified,
identify each PSU and Life Vest Panel and each lanyard as-
sembly.
Inspect each PSU to find if it has the correct reidentification
part number, and change the reidentification part number on
the PSU(s) if an incorrect one is found.
Airplanes that have added and
replaced lanyard assemblies on
PSUs and Life Vest Panels, and
that have made sure that the
lanyards installed on the PSUs
and Life Vest Panels were ser-
viceable.
Group 8, Con-
figuration 3
Measure the distance between the hooks of the torsion spring
of each lanyard assembly, part number 417A3003-9. If the
measured distance is less than specified, replace each lan-
yard assembly and identify each Life Vest Panel and each
replaced lanyard assembly. If the measured distance is equal
to or greater than specified, identify each Life Vest Panel and
each lanyard assembly.
Airplanes that have made sure
that the lanyards installed on the
PSUs in production were ser-
viceable, but not for Life Vest
Panels.
Group 9, Con-
figuration 2
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-600, 737-700, 737-700C,
737-800, 737-900, 737-900ER
Group 2, 7:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-700, 737-800
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
24 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 25

Group 3:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-700C, 737-800
Group 4, 6, 9:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-800
Group 5, 8:
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-700
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2019-03-26 is related to this service
bulletin. The effective date of AD 2019-03-26 is April 8, 2019.
Boeing recommends that the inspection, change and/or repair given in this service bulletin be done
within 60 months after the effective date of AD 2019-03-26.
F. Approval
NOTE: The approval statement that follows is valid for 737-700C airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved for all airplanes
listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other approved Boeing changes.
In addition, the Manager of the FAA Seattle ACO approves the accomplishment of addition and
replacement of lanyards on PSUs and Life Vest Panels, and the inspection of lanyards, of this service
bulletin revision, as an Alternative Method of Compliance (AMOC) to the requirements of paragraph
(g) of AD 2019-03-26. All provisions of AD 2019-03-26 that are not specifically referenced in the above
statement remain fully applicable and must be complied with.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
NOTE: The approval statement that follows is valid for all affected airplanes, except 737-700C
airplanes.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
25 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 26

This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
In addition, the Manager of the FAA Seattle ACO approves the accomplishment of addition and
replacement of lanyards on PSUs and Life Vest Panels, and the inspection of lanyards, of this service
bulletin revision, as an Alternative Method of Compliance (AMOC) to the requirements of paragraph
(g) of AD 2019-03-26. All provisions of AD 2019-03-26 that are not specifically referenced in the above
statement remain fully applicable and must be complied with.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The tables below show an estimate of the task hours necessary to do this modification for each PSU/Life
Vest Panel. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate
with operator task hour data if necessary. The estimate does not include lost time. These are some
examples of lost time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Group 1-2, 5, 7-8, Configuration 1:
Part 1 - Airplane Work: PSU
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.300.301FIGURE 1
0.050.051Close Access
0.400.40TOTAL FOR EACH PSU
Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group
6, 9, Configuration 1:
Part 1 - Airplane Work: PSU
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.050.051FIGURE 3
0.050.051FIGURE 5
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
26 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 27

Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group
6, 9, Configuration 1:
Part 1 - Airplane Work: PSU
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251FIGURE 6(a)
0.050.051Close Access
(b)(b)TOTAL FOR EACH PSU
(a) Applicable only if the lanyard assemblies is to be replaced.
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each PSU.
Group 7-8, Configuration 2:
Part 1 - Airplane Work: PSU
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.050.051FIGURE 3
0.050.051FIGURE 5
0.250.251FIGURE 6(a)
0.250.251FIGURE 9
0.050.051Close Access
(b)(b)TOTAL FOR EACH PSU
(a) Applicable only if the lanyard assemblies is to be replaced.
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each PSU.
Group 7-8, Configuration 3:
Part 1 - Airplane Work: PSU
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.250.251FIGURE 9
0.050.051Close Access
0.350.35TOTAL FOR EACH PSU
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
27 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 28

Group 2, Configuration 1; Group 5; Group 8, Configuration 1:
Part 1 - Airplane Work: Life Vest Panel
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.300.301FIGURE 2
0.050.051Close Access
0.400.40TOTAL FOR EACH LIFE VEST PANEL
Group 2, Configuration 2; Group 4, Configuration 1; Group 8, Configuration 2; Group 9:
Part 1 - Airplane Work: Life Vest Panel
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051Open Access
0.050.051FIGURE 4
0.050.051FIGURE 7
0.250.251FIGURE 8(a)
0.050.051Close Access
(b)(b)TOTAL FOR EACH LIFE VEST PANEL
(a) Applicable only if the lanyard assemblies is to be replaced.
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each life vest panel.
Part 2 - Component Work: PSU - 417N3011-( ) - Without Added And Replaced Lanyard As-
semblies
Elapsed HoursTask HoursNumber of PersonsTask
0.300.301FIGURE 1
0.300.30TOTAL FOR EACH PSU
Part 2 - Component Work: PSU - 417N3011-( ) - With Added And Replaced Lanyard Assem-
blies, Not Reidentified In Accordance With The Original Issue or Revision 1 of This Service
Bulletin
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051FIGURE 3
0.050.051FIGURE 5
0.250.251FIGURE 6(a)
(b)(b)TOTAL FOR EACH PSU
(a) Applicable only if the lanyard assemblies is to be replaced.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
28 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 29

Part 2 - Component Work: PSU - 417N3011-( ) - With Added And Replaced Lanyard Assem-
blies, Not Reidentified In Accordance With The Original Issue or Revision 1 of This Service
Bulletin
Elapsed HoursTask HoursNumber of PersonsTask
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each PSU panel.
Part 2 - Component Work: PSU - 417N3011-2659B thru 417N3011-2674BM, 417N3011-2401B
thru 417N3011-2404B, 417N3011-2413B, 417N3011-2414B - With Added And Replaced Lanyard
Assemblies
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051FIGURE 3
0.050.051FIGURE 5
0.250.251FIGURE 6(a)
0.250.251FIGURE 9
(b)(b)TOTAL FOR EACH PSU
(a) Applicable only if the lanyard assemblies is to be replaced.
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each PSU panel.
Part 2 - Component Work: Life Vest Panel - 417N3070-( ) - Without Added And Replaced
Lanyard Assemblies
Elapsed HoursTask HoursNumber of PersonsTask
0.300.301FIGURE 2
0.300.30TOTAL FOR EACH LIFE VEST PANEL
Part 2 - Component Work: PSU - Life Vest Panel: 417N3070-( ) - With Added And Replaced
Lanyard Assemblies
Elapsed HoursTask HoursNumber of PersonsTask
0.050.051FIGURE 4
0.050.051FIGURE 7
0.250.251FIGURE 8(a)
(b)(b)TOTAL FOR EACH LIFE VEST PANEL:
(a) Applicable only if the lanyard assemblies is to be replaced.
(b) A total is not given as task usage is variable. Add the values of the applicable
tasks together to get the total for each life vest panel.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
29 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 30

Group 1-2, Configuration 2:
Check Kits
Elapsed HoursTask HoursNumber of PersonsTask
0.100.101APPENDIX D
0.100.10TOTAL FOR EACH KIT
H. Weight and Balance Changes
Group 1-2, Configuration 1; Group 5; Group 7-8, Configuration 1:
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
(b)+ 0.02 (a)737-600/700/700C/800/900/900ER
(a) Change is for one PSU or Life Vest Panel. Multiply by the number of PSUs or Life Vest
Panels changed to get the total Weight change. Use one of the methods that follow
(although Method 1 is the recommendation) to find the number of PSUs or Life Vest
Panels:
– Method 1 - Count the PSUs or Life Vest Panels manually.
– Method 2 - Use the total number of seat groups to get an estimate, for example,
triples plus doubles plus singles.
– Method 3 - Use the number of revenue passengers divided by 3 to get an estimate,
for example 200 divided by 3 equals 67 PSUs.
(b) For Change in Moment, use the total change in weight multiplied by 700 to get the
change in moment. 700 is the typical balance arm length in inches.
Group 1, Configuration 2-3; Group 2, Configuration 2-3; Group 3-4, 6; Group 7, Configuration
2-3; Group 8, Configuration 2-3; Group 9:
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 39004
b. Boeing Service Bulletin 737-25-1545, 737-25-1614, 737-35-1107
c. Boeing Service Related Problem (SRP) 737NG-SRP-25-0342
d. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2019-03-26
e. Service Bulletin Index D6-19567
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
30 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 31

f. Standard Overhaul Practices Manual (SOPM) 20-50-01, 20-50-10, 20-50-12
g. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 25-23-61
h. 737NG Fleet Team Digest (FTD) 25-14002
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
PSU INSTALLATION417A3100
KIT - PSU INSTL849A6011
The table above lists applicable drawing used to prepare this service bulletin. The drawing is not
necessary to make the specified changes, and is not supplied with this service bulletin. The drawing
may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
25-20737-600/700/800/900 Aircraft Maintenance
Manual - System Description Section
25-23737-600/700/800/900 Aircraft Maintenance
Manual - Practices and Procedures
11-30, 11-32, 21-24, 23-31, 25-23,
33-23, 33-27, 35-22
737-600/700/800/900 Illustrated Parts Cata-
log
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary for Each Airplane, for interchangeability and intermixability
information.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
31 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 32

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
32 of 87
BOEING SERVICE BULLETIN 737-25-1707
BLANK PAGE

### Page 33

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary for Each Airplane, and Paragraph
2.D., Parts Necessary to Change Spares. Operators are encouraged to share schedule requirements
with Boeing for incorporation of the service bulletin. The parts are subject to the terms and conditions
of the Boeing standard purchase order acknowledgment. Prices are in United States Dollars. Terms:
Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
Operators are encouraged to complete the survey provided in APPENDIX C of this service bulletin to
help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
Group 1-2, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 1 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
-Top Kit - PSU Panel
Modification - Lanyard
Improvement
002A0002-451 (a)
(a) Not available for procurement. This kit is replaced by kit 002A0002-500. The Bill Of Materials of top kits
002A0002-500 and 002A0002-451 are the same. The only difference is that the 417A3003-9 lanyard as-
sembly in top kit 002A0002-500 is serviceable. Refer to Paragraph 2.C.1., Kits/Parts.
Group 2, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 1 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
-Top Kit - Life Vest Pan-
el Modification - Lan-
yard Improvement
002A0002-452 (a)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
33 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 34

Group 2, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 1 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
(a) Not available for procurement. This kit is replaced by kit 002A0002-501. The Bill Of Materials of top kits
002A0002-501 and 002A0002-452 are the same. The only difference is that the 417A3003-9 lanyard as-
sembly in top kit 002A0002-501 is serviceable. Refer to Paragraph 2.C.1., Kits/Parts.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
34 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 35

Group 1-2, 5, 7-8, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
$186.00213500April 11, 2018REPLACEMENT KIT
- PSU PANEL MODI-
FICATION - LAN-
YARD IMPROVE-
MENT
002A0002-500
500April 18, 2018
500April 25, 2018
500May 2, 2018
500May 9, 2018
500May 16, 2018
500May 23, 2018
500May 31, 2018
500June 7, 2018
500June 14, 2018
500June 21, 2018
500June 28, 2018
500July 6, 2018
500July 13, 2018
500July 20, 2018
500July 27, 2018
500August 3, 2018
500August 10, 2018
500August 17, 2018
500August 24, 2018
500August 31, 2018
500September 10, 2018
500September 17, 2018
500September 24, 2018
500October 1, 2018
500October 8, 2018
500October 15, 2018
500October 22, 2018
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
35 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 36

Group 1-2, 5, 7-8, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
October 29, 2018 500
500November 5, 2018
Group 2, Configuration 1; Group 5; Group 8, Configuration 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
$196.00213500January 5,
2018
REPLACEMENT KIT -
LIFE VEST PANEL
MODIFICATION - LAN-
YARD IMPROVEMENT
002A0002-501
500February 2,
2018
500March 2, 2018
500March 30,
2018
500April 27, 2018
500May 25, 2018
500June 25, 2018
266July 24, 2018
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
36 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 37

Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3-4, Configuration 1; Group 5, Configuration
2; Group 6, Configuration 1; Group 7-8, Configuration 2; Group 9:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNamePart Number
$103.00213600(c)SUPPLEMENTAL KIT
- SPRING CLIP - LAN-
YARD IMPROVEMENT
002A0002-502
(a)(b) 1,000April 19, 2018
1,000April 26, 2018
1,000May 3, 2018
2,700May 10, 2018
2,700May 17, 2018
1,000May 24, 2018
1,000June 1, 2018
1,000June 8, 2018
1,000June 15, 2018
4,500June 29, 2018
4,500July 9, 2018
(a) Boeing recommends that operators order this kit before airplanes are inspected or kits are checked such
that lanyard assemblies that have a measured distance of less than 0.83 inches can be replaced immedi-
ately. Order this kit for the quantity of Passenger Service Units (PSUs) or PSUs and Life Vest Panels on
each airplane, or for the quantity of 002A0002-451 or 002A0002-452 kits on hand. Refer to Paragraph
3.B., Work Instructions, or APPENDIX D for the kit check.
(b) This supplemental kit is only necessary for Group 1-2, Configuration 1 airplanes if kit(s) 002A0002-451/-
452 were received, but the modification in accordance with this service bulletin is not done.
(c) Available to ship on receipt of purchase order.
Group 7-8, Configuration 3:
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
37 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 38

B. Industry Support Information
Group 1-2, Configuration 1:
Boeing warranty remedies are not available for the modification given in this service bulletin.
Notwithstanding, for any kit P/N 002A0002-451, and as applicable kit P/N 002A0002-452, received
from Boeing but not yet installed, Boeing warranty remedies are available for the inspection and, if
necessary, replacement of any defective P/N 471A3003-9 lanyard assembly in accordance with
APPENDIX D. The replacement lanyard assembly for any kits will be supplied at no charge. Send a
purchase order for the P/N 002A0002-502 kit to Boeing Material Management. Please reference this
service bulletin number and the airplane variable number(s) in your purchase order. For task hour
reimbursement of APPENDIX D, send a warranty claim to BCA Contracts - Warranty. The warranty
claim must include original Boeing kit purchase order.
Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group 6,
Configuration 1; Group 7-8, Configuration 2; Group 9:
Boeing warranty remedies are available for airplanes in warranty as of December 13, 2017 for the
dimensional inspection and, if necessary, replacement of any defective P/N 417A3003-9 lanyard
assembly. The replacement lanyard assembly will be supplied at no charge. Send a purchase order
for the P/N 002A0002-502 kit to Boeing Material Management. Please reference this service bulletin
number and the airplane variable number(s) in your purchase order. For task hour reimbursement,
send a warranty claim to BCA Contracts - Warranty.
All warranty remedies will expire eight years from the Revision 1 date of this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit or supplemental kit and the items shown in Paragraph 2.C.2., Parts
and Materials Supplied by the Operator, is necessary for each PSU or Life Vest
Panel.
1.
2. If you have top kit 002A0002-451, it must be checked before use. Refer to
APPENDIX D.
3. If you have top kit 002A0002-452, it must be checked before use. Refer to
APPENDIX D.
Group 1-2, 5, 7-8, Configuration 1:
Kit 002A0002
NotesExisting Part
Number
NameQTYNew Part Number
-500
REPLACEMENT
KIT - PSU PANEL
MODIFICATION -
LANYARD IM-
PROVEMENT
-002A0002-500
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
38 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 39

Group 1-2, 5, 7-8, Configuration 1:
Kit 002A0002
NotesExisting Part
Number
NameQTYNew Part Number
-500
(a)LANYARD ASSY,
STD CLIP, PSU
2417A3003-2
(a)(d)417N3190-1LANYARD ASSY,
SPRING CLIP,
PSU
1417A3003-9
(b)WASHER FLAT3NAS1149C0316R
(b)(c)SCREW3NAS1301-6-5
(a) This part is used in production.
(b) There are more parts than are necessary.
(c) If grip length shown is not available at Boeing, fasteners supplied in kits
may be one grip length longer than indicated. Also, if any fasteners part
numbers listed are not available or have been superseded, substitute
fasteners may be supplied in kits.
(d) The lanyard assembly supplied in this kit is in a serviceable condition as
defined in this service bulletin, but will not have a white mark on it. Refer
to Paragraph 3.A., General Information. A white mark is applied in FIG-
URE 1.
Group 2, Configuration 1; Group 5; Group 8, Configuration 1:
Kit 002A0002
NotesExisting Part
Number
NameQTYNew Part Number
-501
REPLACEMENT
KIT - LIFE VEST
PANEL MODIFICA-
TION - LANYARD
IMPROVEMENT
-002A0002-501
(a)LANYARD ASSY,
STD CLIP, PSU
2417A3003-2
(a)(d)417N3190-1LANYARD ASSY,
SPRING CLIP,
PSU
1417A3003-9
(b)(c)BACS12HN08-6 or
BACS12FA08K6
BOLT3BACS12HN08-8
(b)WASHER FLAT3NAS1149C0316R
(b)(c)SCREW3NAS1301-6-5
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
39 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 40

Group 2, Configuration 1; Group 5; Group 8, Configuration 1:
Kit 002A0002
NotesExisting Part
Number
NameQTYNew Part Number
-501
(a) This part is used in production.
(b) There are more parts than are necessary.
(c) If grip length shown is not available at Boeing, fasteners supplied in kits
may be one grip length longer than indicated. Also, if any fasteners part
numbers listed are not available or have been superseded, substitute
fasteners may be supplied in kits.
(d) The lanyard assembly supplied in this kit is in a serviceable condition as
defined in this service bulletin, but will not have a white mark on it. Refer
to Paragraph 3.A., General Information. A white mark is applied in FIG-
URE 2.
Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3-4, Configuration 1; Group
5, Configuration 2; Group 6, Configuration 1; Group 7-8, Configuration 2; Group 9:
Kit 002A0002
NotesExisting Part
Number
NameQTYNew Part Number
-502
SUPPLEMENTAL
KIT - SPRING
CLIP - LANYARD
IMPROVEMENT
-002A0002-502
(a)(b)417N3003-9LANYARD ASSY,
SPRING CLIP,
PSU
1417A3003-9
(a) This part is used in production.
(b) The lanyard assembly supplied in this kit is in a serviceable condition as
defined in this service bulletin, but will not have a white mark on it. Refer
to Paragraph 3.A., General Information. A white mark is applied in FIG-
URE 5 or FIGURE 6 and FIGURE 7 or FIGURE 8.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
40 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 41

NotesNameQTYPart Number /
Specification
(a)(b)LOCTITE1/4 fl.
oz.
222MS (MIL-S-
46163A TYPE II
GRADE M)
(a) Can be purchased from: Henkel Loctite Corporation., 15051 E. Don Julian Road, City of
Industry, California 91746, CAGE Code: 12405.
(b) Can be purchased from: Boeing Distribution Inc (previously Aviall), 2750 Regent Boulevard,
Dallas, Texas 75261, Telephone: 1-800-Aviall-1, Website: http://www.aviall.com, CAGE
Code: 22819.
Group 2, Configuration 1-2; Group 4, Configuration 1; Group 5; Group 6-8, Configuration 1; Group
8, Configuration 2; Group 9:
NotesNameQTYPart Number /
Specification
(a)WASHER FLAT2NAS1149DN816J
(a) Quantity necessary is for each Life Vest Panel when a new BACS12HN08-8 bolt replaces
a BACS12FA08K6 bolt. Refer to FIGURE 2 or FIGURE 8.
Group 1-2, Configuration 3; Group 3-5, Configuration 2; Group 5, Configuration 3; Group
6, Configuration 2; Group 7-8, Configuration 3:
None.
3. Parts Modified and Reidentified
The parts shown below are changed as shown in this service bulletin. The quantity (QTY) is the
number of parts changed for each PSU or Life Vest Panel. Components or subassembly parts are
indented. The quantity of the indented part is the number of parts used on the next higher assembly.
NotesNew Part NumberNameQTYExisting Part
Number
(a)(c)(g)417N3011-( ) or
002A0002-( )
Passenger Service Unit
(PSU)
-417N3011-( ) or
002A0002-( )
(a)(f)-Clamp Assy2. 417N3180-1
(a)(g)(h)417A3003-9Lanyard Assy, Spring
Clip, PSU
1. 417A3003-9
(a)(d)(g)417N3070-( )Life Vest Panel-417N3070-( )
(e)(g)-Life Vest Assy-Underbin1. 417N3014-( )
(a)(f)-Clamp Assy2. . 417N3180-1
(a)(g)(h)417A3003-9Lanyard Assy, Spring
Clip, PSU
1. . 417A3003-9
(a) Make the change in accordance with this service bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
41 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 42

NotesNew Part NumberNameQTYExisting Part
Number
(b) Identify on the part that the change done in accordance with this service bulletin was made.
(c) Refer to APPENDIX A for the new part number of each changed PSU.
(d) Refer to APPENDIX B for the new part number of each changed Life Vest Panel.
(e) The equivalent production part numbers are 417N3014-5 and 417N3014-6.
(f) The equivalent production part number is 417N3180-4.
(g) You cannot use the existing part to replace the new or changed part.
(h) The part number pre and post this service bulletin is the same, but a white mark on the
lanyard assembly, post this service bulletin, identifies that it is serviceable as defined in
this service bulletin. Refer to Paragraph 3.A., General Information.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
To get the parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTESNAMEQTYPART NUMBER
(a)(b)LANYARD ASSY, STD
CLIP, PSU
2417A3003-2
(a)(b)(c)LANYARD ASSY, SPRING
CLIP, PSU
1417A3003-9
(a)(b)SCREW2NAS1301-6-5
(b)BOLT2BACS12HN08-8
(a)(b)WASHER FLAT2NAS1149C0316R
(d)WASHER FLAT2NAS1149DN816J
(a) Necessary for each PSU without added and replaced lanyard assemblies.
(b) Necessary for each Life Vest Panel without added and replaced lanyard assemblies.
(c) Necessary for each PSU or Life Vest Panel, with added and replaced lanyard assemblies, that does not
have a serviceable lanyard assembly.
(d) Necessary for each Life Vest Panel when a new BACS12HN08-8 bolt replaces a BACS12FA08K6 bolt.
Refer to FIGURE 2.
E. Special Tooling - Price and Availability
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
42 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 43

F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
43 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 44

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
44 of 87
BOEING SERVICE BULLETIN 737-25-1707
BLANK PAGE

### Page 45

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF
METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE
BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES
CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
45 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 46

8. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
9. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
10. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. If a step or sub-step is labeled
"RC Exempt," then the RC requirement is removed from that step or sub-step. An
Alternative Method of Compliance (AMOC) is required for any deviations to RC steps,
including sub-steps and identified figures. Steps not labeled as RC may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC. This is provided that
the RC steps, including sub-steps and identified figures, can still be done as specified,
and the airplane can be put back in an airworthy condition.
11. A serviceable 417A3003-9 lanyard assembly is defined in this service bulletin as one
that has a white mark applied on it. The white mark identifies that the lanyard
assembly was manufactured correctly to have a distance of 0.83 - 0.89 inches
between the hooks of its torsion spring.
B. WORK INSTRUCTIONS
Group 1-2, Configuration 3; Group 3-4, 6, Configuration 2:
1. No further action required.
Group 1, Configuration 1-2; Group 2, Configuration 1-2; Group 3-4, Configuration 1; Group 5;
Group 6, Configuration 1; Group 7-9:
Part 1 - Airplane Work
1. At each Passenger Service Unit (PSU) location:
a. Lower the PSU. Refer to 737-600/700/800/900 AMM 25-23-61 as an accepted procedure.
NOTE: Do not disconnect hose and electrical connections.
b. Group 1-2, 5, 7-8, Configuration 1:
RC - Add and replace lanyard assemblies in accordance with FIGURE 1.
c. Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group
6, Configuration 1; Group 7-8, Configuration 2; Group 9, Configuration 1:
Disconnect lanyard assembly, part number 417A3003-9, at the torsion spring end, from the
PSU rail.
d. Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration 2; Group
6, Configuration 1; Group 7-8, Configuration 2; Group 9, Configuration 1:
RC - Measure the distance between the hooks of the torsion spring of the lanyard assembly
in accordance with FIGURE 3.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
46 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 47

(1) If the measured distance is 0.83 inches or greater, identify the PSU and that the lanyard
assembly is serviceable in accordance with FIGURE 5.
(2) If the measured distance is less than 0.83 inches, replace the lanyard assembly in
accordance with FIGURE 6.
e. Group 7, Configuration 2-3; Group 8, Configuration 2-3:
RC - Inspect each PSU to find if it has the correct reidentification part number, and change
the reidentification part number on the PSU(s) if an incorrect one is found in accordance with
FIGURE 9.
f. Close the PSU. Refer to 737-600/700/800/900 AMM 25-23-61 as an accepted procedure.
2. Group 2, Configuration 1-2; Group 4, Configuration 1; Group 5; Group 8, Configuration 1-2;
Group 9:
At each Life Vest Panel location:
a. Lower the Life Vest Panel. Refer to 737-600/700/800/900 AMM 25-23-61 as an accepted
procedure.
b. Group 2, Configuration 1; Group 5; Group 8, Configuration 1:
RC - Add and replace lanyard assemblies in accordance with FIGURE 2.
c. Group 2, Configuration 2; Group 4, Configuration 1; Group 8, Configuration 2; Group
9:
Disconnect lanyard assembly, part number 417A3003-9, at the torsion spring end, from the
PSU rail.
d. Group 2, Configuration 2; Group 4, Configuration 1; Group 8, Configuration 2; Group
9:
RC - Measure the distance between the hooks of the torsion spring of the lanyard assembly
in accordance with FIGURE 4.
(1) If the measured distance is 0.83 inches or greater, identify the Life Vest Panel and that
the lanyard assembly is serviceable in accordance with FIGURE 7.
(2) If the measured distance is less than 0.83 inches, replace the lanyard assembly in
accordance with FIGURE 8.
e. Close the Life Vest Panel. Refer to 737-600/700/800/900 AMM 25-23-61 as an accepted
procedure.
3. Put the airplane back to a serviceable condition.
Part 2 - Component Work
1. PSU:
417N3011-( ) - Without Added And Replaced Lanyard Assemblies
a. Add and replace lanyard assemblies in accordance with FIGURE 1.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
47 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 48

417N3011-( ) - With Added And Replaced Lanyard Assemblies, Not Reidentified In Accordance
With Revision 1 of This Service Bulletin
a. Measure the distance between the hooks of the torsion spring of the lanyard assembly in
accordance with FIGURE 3.
(1) If the measured distance is 0.83 inches or greater, identify the PSU and that the lanyard
assembly is serviceable in accordance with FIGURE 5.
(2) If the measured distance is less than 0.83 inches, replace the lanyard assembly in
accordance with FIGURE 6.
417N3011-2659B thru 417N3011-2674BM, 417N3011-2401B thru 417N3011-2404B,
417N3011-2413B, 417N3011-2414B - With Added And Replaced Lanyard Assemblies, Not
Reidentified In Accordance With Revision 1 of This Service Bulletin
a. Measure the distance between the hooks of the torsion spring of the lanyard assembly in
accordance with FIGURE 3.
(1) If the measured distance is 0.83 inches or greater, identify the PSU and that the lanyard
assembly is serviceable in accordance with FIGURE 5.
(2) If the measured distance is less than 0.83 inches, replace the lanyard assembly in
accordance with FIGURE 6.
b. Inspect each PSU to find if it has the correct reidentification part number, and change the
reidentification part number on the PSU(s) if an incorrect one is found in accordance with
FIGURE 9.
417N3011-2659B thru 417N3011-2674BM, 417N3011-2401B thru 417N3011-2404B,
417N3011-2413B, 417N3011-2414B - With Added And Replaced Lanyard Assemblies,
Reidentified In Accordance With Revision 1 of This Service Bulletin
a. Inspect each PSU to find if it has the correct reidentification part number, and change the
reidentification part number on the PSU(s) if an incorrect one is found in accordance with
FIGURE 9.
2. Life Vest Panel:
417N3070-( ) - Without Added And Replaced Lanyard Assemblies
a. Add and replace lanyard assemblies in accordance with FIGURE 2.
417N3070-( ) - With Added And Replaced Lanyard Assemblies
a. Measure the distance between the hooks of the torsion spring of the lanyard assembly in
accordance with FIGURE 4.
(1) If the measured distance is 0.83 inches or greater, identify the Life Vest Panel and that
the lanyard assembly is serviceable in accordance with FIGURE 7.
(2) If the measured distance is less than 0.83 inches, replace the lanyard assembly in
accordance with FIGURE 8.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2: July 27, 2020
48 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 49 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
This Figure applies only to: Group 1-2, 5, 7-8, Configuration 1.
PSU RAIL
TYPICAL
(PSU (SHOWN CLOSED))
TORSION (8
SPRING
2796166
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 1 OF 5)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  Copyright © Unpublished  737-25-1707
Work - See page 1 for details.  49 of 87

### Page 50 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
₴ 3)
2796167
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 2 OF 5)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  737-25-1707
Copyright © Unpublished
Work - See page 1 for details.  50 of 87

### Page 51 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
PLUNGER
PLUNGER
2796168
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 3 OF 5)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  Copyright © Unpublished
Work - See page 1 for details.  28 10 19

### Page 52

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each Passenger Service Unit.
More DataQtyIdentificationNameTaskStep
(a)1417N3190-1LANYARD ASSEMBLYRemove1
2-BOLTRemove / Keep2
2-WASHERRemove / Keep
Make sure the lan-
yard assembly is
from kit 002A0002-
500.
1417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Install (New)3
2-WASHERInstall (Kept)
2-BOLTInstall (Kept)
(g)1417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Identify
2-BOLTRemove / Keep4
2-WASHERRemove / Keep
2417A3003-2LANYARD ASSY, STD
CLIP, PSU
Install (New)5
2-BOLTInstall (Kept)
2-WASHERInstall (Kept)
(c)-417A3003-2LANYARD ASSY, STD
CLIP, PSU
Attach6
(d)-222MS (MIL-S-46163A
TYPE II GRADE M)
LOCTITEApply
2NAS1149C0316RWASHER FLATInstall (New)
(e)2NAS1301-6-5SCREWInstall (New)
(f)1417N3011-( ) OR
002A0002-( )
PASSENGER SER-
VICE UNIT
Identify7
(h)-737-25-1707 R02SERVICE BULLETIN
NUMBER
Apply
(b)-417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Attach8
(a) Support the PSU during the disconnection and removal of the lanyard assembly to prevent breakage of
the clamp assemblies on the outboard edge of the PSU.
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2 July 27, 2020
52 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 53

More DataQtyIdentificationNameTaskStep
(b) Attach the torsion spring in the nearest larger hole in the PSU rail. During attachment make sure the torsion
spring is compressed to get the hooks fully into the larger hole of the PSU rail. Release compression and
pull down on the lanyard assembly. If the hooks of the torsion spring are not fully engaged, the torsion
spring could come out of the hole and the PSU could become detached from the PSU rail. The torsion
spring will rotate freely in the hole of the PSU rail as the PSU is closed. This does not affect retention.
(c) The plunger goes through the hole in the clip of the lanyard assembly.
(d) Refer to SOPM 20-50-12 as an accepted procedure.
(e) Screw into the end of the plunger which has a threaded hole in it. Make sure the screw is not loose.
(f) Remove the old part number and re-identify each changed PSU with the new part number, on a non-
decorative surface. Refer to APPENDIX A for the new part number of each changed PSU. A white pen
or sticker can be used for better contrast on a dark background. Refer to SOPM 20-50-10 as an accepted
procedure.
(g) Identify the lanyard assembly as serviceable with a permanent white mark, that can be easily seen when
the PSU is lowered. Refer to SOPM 20-50-10 as an accepted procedure.
(h) Apply to the PSU, on a non-decorative surface, to show that the change in accordance with this service
bulletin is done. A white pen or sticker can be used for better contrast on a dark background. Refer to
SOPM 20-50-10 as an accepted procedure.
FIGURE 1: PASSENGER SERVICE UNIT, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2 July 27, 2020
53 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 54 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
This Figure applies only to: Group 2, Configuration 1; Group 5; Group 8, Configuration 1.
TYPICAL  PSU RAIL
(LIFE VEST PANEL
(SHOWN CLOSED)
TORSION (13
SPRING
FASTEN STRAPS  OVER LIFEVESTS  SECUREL Y
2796169
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 1 OF 6)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  737-25-1707
Copyright © Unpublished
Work - See page 1 for details.  54 of 87

### Page 55 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
34
2796170
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 2 OF 6)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  Copyright © Unpublished  737-25-1707
Work - See page 1 for details.  55 of 87

### Page 56 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
PLUNGER
PLUNGER
10
2796171
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 3 OF 6)
Original issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  737-25-1707
Copyright © Unpublished
Work - See page 1 for details.  56 of 87

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each Life Vest Panel.
More DataQtyIdentificationNameTaskStep
(a)1417N3190-1LANYARD ASSEMBLYRemove1
1-BOLTRemove2
If installed.1-WASHERRemove / Keep
Disconnect only at
the end specified.
1417N3190-17LIFE VEST DOOR
LANYARD
Disconnect
1-BOLTRemove / Keep3
If installed.1-WASHERRemove / Keep
Make sure the lan-
yard assembly is
from kit 002A0002-
501.
1417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Install (New)4
Put the free end
back in position. (g)
1417N3190-17LIFE VEST DOOR
LANYARD
Connect
If removed.1-WASHERInstall (Kept)
If a washer was not
removed.
1NAS1149DN816JWASHERInstall (New)
1BACS12HN08-8BOLTInstall (New)
(h)1417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Identify
1-BOLTInstall (Kept)5
If removed.1-WASHERInstall (Kept)
1-BOLTRemove / Keep6
If installed.1-WASHERRemove / Keep
1417A3003-2LANYARD ASSY, STD
CLIP, PSU
Install (New)7
1-BOLTInstall (Kept)
If removed.1-WASHERInstall (Kept)
(c)-417A3003-2LANYARD ASSY, STD
CLIP, PSU
Attach8
(d)-222MS (MIL-S-46163A
TYPE II GRADE M)
LOCTITEApply
(e)1NAS1301-6-5SCREWInstall (New)
1NAS1149C0316RWASHER FLATInstall (New)
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 4 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2 July 27, 2020
57 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 58

More DataQtyIdentificationNameTaskStep
1-BOLTRemove9
If installed.1-WASHERRemove / Keep
Disconnect only at
the end identified.
1417N3190-17LIFE VEST DOOR
LANYARD
Disconnect
1417A3003-2LANYARD ASSY, STD
CLIP, PSU
Install (New)10
Put the free end
back in position. (g)
1417N3190-17LIFE VEST DOOR
LANYARD
Connect
If removed.1-WASHERInstall (Kept)
If a washer was not
removed.
1NAS1149DN816JWASHERInstall (New)
1BACS12HN08-8BOLTInstall (New)
(c)-417A3003-2LANYARD ASSY, STD
CLIP, PSU
Attach11
(f)-222MS (MIL-S-46163A
TYPE II GRADE M)
LOCTITEApply
(e)1NAS1301-6-5SCREWInstall (New)
1NAS1149C0316RWASHER FLATInstall (New)
(f)1417N3070-( )LIFE VEST PANELIdentify12
(i)-737-25-1707 R02SERVICE BULLETIN
NUMBER
Apply
(b)-417A3003-9LANYARD ASSY,
SPRING CLIP, PSU
Attach13
(a) Support the Life Vest Panel during the disconnection and removal of the lanyard assembly to prevent
breakage of the clamp assemblies on the outboard edge of the Life Vest Panel.
(b) Attach the torsion spring in the nearest larger hole in the PSU rail. During attachment make sure the torsion
spring is compressed to get the hooks fully into the larger hole of the PSU rail. Release compression and
pull down on the lanyard assembly. If the hooks of the torsion spring are not fully engaged, the torsion
spring could come out of the hole and the Life Vest Panel could become detached from the PSU rail. The
torsion spring will rotate freely in the hole of the PSU rail as the Life Vest Panel is closed. This does not
affect retention.
(c) The plunger goes through the hole in the clip of the lanyard assembly.
(d) Refer to SOPM 20-50-12 as an accepted procedure.
(e) Screw into the end of the plunger which has a threaded hole in it. Make sure the screw is not loose.
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2 July 27, 2020
58 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 59

More DataQtyIdentificationNameTaskStep
(f) Remove the old part number and re-identify each changed Life Vest Panel with the new part number, on
a non-decorative surface. Refer to APPENDIX B for the new part number of each changed Life Vest
Panel. A white pen or sticker can be used for better contrast on a dark background. Refer to SOPM 20-
50-10 as an accepted procedure.
(g) The terminal end of 417N3190-17 can be moved to install 417A3003-2.
(h) Identify the lanyard assembly as serviceable with a permanent white mark, that can be easily seen when
the Life Vest Panel is lowered. Refer to SOPM 20-50-10 as an accepted procedure.
(i) Apply to the Life Vest Panel, on a non-decorative surface, to show that the change in accordance with
this service bulletin is done. A white pen or sticker can be used for better contrast on a dark background.
Refer to SOPM 20-50-10 as an accepted procedure.
FIGURE 2: LIFE VEST PANEL, LANYARD ASSEMBLIES - ADDITION AND REPLACEMENT
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2015
737-25-1707Revision 2 July 27, 2020
59 of 87
BOEING SERVICE BULLETIN 737-25-1707

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-25-1707
This Figure applies only to: Group 1-2, Configuration 2; Group 3-4, Configuration 1; Group 5, Configuration
2; Group 6, Configuration 1; Group 7-8, Configuration 2; Group 9, Configuration 1.
HOOK
TORSION SPRING
0.89
0.83
A-A
TYPICAL  HOOK
(PSU (SHOWN CLOSED))
2796356
FIGURE 3: PASSENGER SERVICE UNIT - LANYARD ASSEMBLY MEASUREMENT
(SHEET 1 OF 2)
Original Issue: September 24, 2015
Revision 2 July 27, 2020  Export Controlled ECCN: 9E991  Copyright © Unpublished  737-25-1707
Work - See page 1 for details.  60 of 87

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-25-1707/file/a7f5f6ff30d2.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
