# Boeing Special Attention Service Bulletin 737-25-1831: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2019-0980, the docket of AD 2019-24-15. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 737-25-1831](https://openairdocs.org/service-documents/boeing/sb-737-25-1831.md)
- Title as filed: 737-25-1831-00--RB
- Pages: 8
- PDF: https://openairdocs.org/files/sha256/c5/d6/c5d6a45fbf67566c3f55129b8084d68c14ffc9ab2ecc3e440bde1c21dd78dca2
- Page: https://openairdocs.org/service-documents/boeing/sb-737-25-1831/file/c5d6a45fbf67

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-25-1831 RB
Original Issue: September 24, 2019
ATA System: 2521
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Mid Exit Door Head Strike
Pads Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2019 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: September 24, 2019
737-25-1831 RB
1 of 8
5.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
2 of 8
REQUIREMENTS BULLETIN 737-25-1831
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
3 of 8
REQUIREMENTS BULLETIN 737-25-1831

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
4 of 8
REQUIREMENTS BULLETIN 737-25-1831
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-25-1831 RB
Original Issue: September 24, 2019
ATA System: 2521
SUBJECT: EQUIPMENT/FURNISHINGS - Passenger Compartment - Mid Exit Door Head Strike
Pads Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to 737-900ER Airplane(s), line number(s) 3771, 3837, 4368, 4711, 4726,
5150, 5223, 5320, 5395, 5412, 5419, 5459, 5639 in 4 Group(s).
DESCRIPTIONCONFIGURATIONGROUP
737-900ER airplane line numbers 3771 and 3837-1
737-900ER airplane line numbers 4368, 4711, and 4726-2
737-900ER airplane line numbers 5150, 5320, 5395, 5419, and 5639-3
737-900ER airplane line numbers 5223, 5412, and 5459-4
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
5 of 8

### Page 6

3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-25-1831 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-25-1831 RB mandatory.
Group 1-3:
Table 1: Head Strike Pads Replacement at left and right Mid Exit Door
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 36 months
after the Original
Issue date of the
Requirements Bul-
letin 737-25-1831
RB
Remove nonconforming
head strike pads one
each on the left and right
Mid Exit Door
All Airplanes
Install conforming head
strike pads one each on
the left and right Mid Exit
Door
Group 4:
Table 2: Head Strike Pads Replacement at left and right Mid Exit Door
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 36 months
after the Original
Issue date of the
Requirements Bul-
letin 737-25-1831
RB
Remove nonconforming
head strike pads two
each on the left and right
Mid Exit Door
All Airplanes
Install conforming head
strike pads two each on
the left and right Mid Exit
Door
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
6 of 8
REQUIREMENTS BULLETIN 737-25-1831

### Page 7

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
7 of 8
REQUIREMENTS BULLETIN 737-25-1831

### Page 8

B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1-3:
Table 1: Head Strike Pads Replacement at left and right Mid Exit Door
Refer to the listed procedures in SB
737-25-1831 Original Issue or later
approved revisions as an accepted
procedure
Method of ComplianceActionCondition
PART 1: PASSENGER COMPART-
MENT, LEFT AND RIGHT SIDE - MID
EXIT DOORS - HEAD STRIKE PAD
REMOVAL
-Remove nonconforming
head strike pads one
each on the left and right
Mid Exit Door
All Airplanes
PART 2: PASSENGER COMPART-
MENT, LEFT SIDE - MID EXIT DOOR
- HEAD STRIKE PAD INSTALLATION
Install conforming head
strike pads one each on
the left and right Mid Exit
Door PART 3: PASSENGER COMPART-
MENT, RIGHT SIDE - MID EXIT DOOR
- HEAD STRIKE PAD INSTALLATION
Group 4:
Table 2: Head Strike Pads Replacement at left and right Mid Exit Door
Refer to the listed procedures in SB
737-25-1831 Original Issue or later
approved revisions as an accepted
procedure
Method of ComplianceActionCondition
PART 1: PASSENGER COMPART-
MENT, LEFT AND RIGHT SIDE - MID
EXIT DOORS - HEAD STRIKE PAD
REMOVAL
-Remove nonconforming
head strike pads two
each on the left and right
Mid Exit Door
All Airplanes
PART 2: PASSENGER COMPART-
MENT, LEFT SIDE - MID EXIT DOOR
- HEAD STRIKE PAD INSTALLATION
Install conforming head
strike pads two each on
the left and right Mid Exit
Door PART 3: PASSENGER COMPART-
MENT, RIGHT SIDE - MID EXIT DOOR
- HEAD STRIKE PAD INSTALLATION
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 24, 2019
737-25-1831 RB
8 of 8
REQUIREMENTS BULLETIN 737-25-1831

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
