# Boeing Special Attention Service Bulletin 737-29-1127: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2019-0114, the docket of AD 2019-14-02. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 737-29-1127](https://openairdocs.org/service-documents/boeing/sb-737-29-1127.md)
- Title as filed: SB-737-29-1127-00--RB
- Pages: 12
- PDF: https://openairdocs.org/files/sha256/86/56/86569929f3753c93eb90def1b61b9f4069e79e8bc35d68a8a989d4ab22675ae5
- Page: https://openairdocs.org/service-documents/boeing/sb-737-29-1127/file/86569929f375

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-29-1127 RB
Original Issue: October 08, 2018
ATA System: 2911 2915
SUBJECT: HYDRAULIC POWER - Hydraulic Systems A and B - Pressure Module Check Valve
Inspection And Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
Copyright © 2018 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: October 08, 2018
737-29-1127 RB
1 of 12
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
2 of 12
REQUIREMENTS BULLETIN 737-29-1127
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
3 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
4 of 12
REQUIREMENTS BULLETIN 737-29-1127
BLANK PAGE

### Page 5

Commercial 
Airplanes
737
Requirements Bulletin
SPECIAL ATTENTION
Number: 737-29-1127 RB
Original Issue: October 08, 2018
ATA System: 2911 2915
SUBJECT: HYDRAULIC POWER - Hydraulic Systems A and B - Pressure Module Check Valve
Inspection And Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. EFFECTIVITY
A. Airplanes
This bulletin is applicable to 737-100/200/200C/300/400/500 Airplanes, line number 1-3132.
DESCRIPTIONCONFIGURATIONGROUP
737-100, 737-200, 737-200C airplanes line numbers 1 thru 291.-1
737-200, 737-200C airplanes that could have one or more Parker
P/N H61C0552M1 pressure module check valves installed in hydraulic
system A.
-2
737-300, 737-400, 737-500 airplanes that could have one or more
Parker P/N H61C0552M1 pressure module check valves installed in
hydraulic systems A and B.
-3
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
5 of 12

### Page 6

3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 737-29-1127 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 737-29-1127 RB mandatory.
Accomplish the required actions, based on the applicable conditions in Table 1, in accordance with the
Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for that
CONDITION or OPTION.
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and permanent
removal from service of any airplanes upon reaching the LOV, whether or not it is operated under FAA
jurisdiction. As such, Boeing no longer provides maintenance instructions for airplanes that have accumulated
flight cycles beyond the LOV. Airplanes in Group 1 (line numbers 1-291) have accumulated flight cycles
beyond the LOV of the maintenance program. 14 CFR 121.1115 and 129.115 prohibit operation of an
airplane beyond its LOV.
Group 2-3:
Table 1: Main Landing Gear Wheel Well - Pressure Module Check Valve Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 5,360 flight
hours after the
original issue date
of Requirements
Bulletin 737-29-
1127 RB.
OPTION 1: Do a check of
maintenance and delivery
records to identify the
part numbers of the two
hydraulic system A pres-
sure module check
valves. (a)(b)
All Group 2 Airplanes
OPTION 2: Do an on-air-
plane inspection for the
part numbers of the two
hydraulic system A pres-
sure module check
valves. (b)
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
6 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 7

Group 2-3:
Table 1: Main Landing Gear Wheel Well - Pressure Module Check Valve Replacement
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 5,360 flight
hours after the
original issue date
of Requirements
Bulletin 737-29-
1127 RB.
OPTION 1: Do a check of
maintenance and delivery
records to identify the
part numbers of the four
hydraulic systems A and
B pressure module check
valves. (a)(b)
All Group 3 Airplanes
OPTION 2: Do an on-air-
plane inspection for the
part numbers of the four
hydraulic systems A and
B pressure module check
valves. (b)
--No further action is re-
quired.
CONDITION 1: NO PARK-
ER P/N H61C0552M1
CHECK VALVE FOUND
-Within 5,360 flight
hours after the
original issue date
of Requirements
Bulletin 737-29-
1127 RB.
Replace with a Crissair
P/N 1C4196 check valve.
CONDITION 2: ANY
PARKER P/N
H61C0552M1 CHECK
VALVE FOUND
(a) It is necessary to do OPTION 2 if the manufacturer's name or part numbers of the installed
check valves cannot be positively identified in the records check.
(b) If the part number cannot be positively identified, it is acceptable to identify the installed
check valve by the manufacturer's name.
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This document and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
7 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 8

Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
8 of 12
REQUIREMENTS BULLETIN 737-29-1127
BLANK PAGE

### Page 9

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Aircraft Maintenance Manual (AMM).
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
9 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 10

— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
6. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for that CONDITION or OPTION.
7. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
8. The instructions in the Work Instructions and the figures can include operation of
tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated Tool and
Equipment Manual, and the Special Tool and Ground Handling Drawing Index contain
data on versions of the tools or test equipment that you can use. It is permitted to
use replaced tools. It is not permitted to use superseded tools.
9. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1:
Boeing endorses the FAA rules related to Limit of Validity (LOV) and recommends immediate and
permanent removal from service of any airplanes upon reaching the LOV, whether or not it is
operated under FAA jurisdiction. As such, Boeing no longer provides maintenance instructions for
airplanes that have accumulated flight cycles beyond the LOV. Airplanes in Group 1 (line numbers
1-291) have accumulated flight cycles beyond the LOV of the maintenance program. 14 CFR
121.1115 and 129.115 prohibit operation of an airplane beyond its LOV.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
10 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 11

Group 2-3:
Table 1: Main Landing Gear Wheel Well - Pressure Module Check Valve Replacement
Refer to the listed proce-
dures in SB 737-29-1127
Original Issue or later
approved revisions as an
accepted procedure:
Method of
Compliance
ActionCondition
Do PART 1: RECORDS
CHECK
-OPTION 1: Do a check of
maintenance and delivery
records to identify the part
numbers of the two hy-
draulic system A pressure
module check valves.
(a)(b)
All Group 2 Airplanes
Do PART 2: PREPARA-
TION
-OPTION 2: Do an on-air-
plane inspection for the
part numbers of the two
hydraulic systems A and B
pressure module check
valves. (b)
Do PART 3: PART NUM-
BER INSPECTION
-
Do PART 1: RECORDS
CHECK
-OPTION 1: Do a check of
maintenance and delivery
records to identify the part
numbers of the four hy-
draulic systems A and B
pressure module check
valves. (a)(b)
All Group 3 Airplanes
Do PART 2: PREPARA-
TION
-OPTION 2: Do an on-air-
plane inspection for the
part numbers of the four
hydraulic systems A and B
pressure module check
valves. (b)
Do PART 3: PART NUM-
BER INSPECTION
-
Do PART 5: RESTORA-
TION if PART 2 was done
-No further action is re-
quired.
CONDITION 1: NO PARK-
ER P/N H61C0552M1
CHECK VALVE FOUND
Do PART 2: PREPARA-
TION if not previously
done
-Replace with a Crissair
P/N 1C4196 check valve.
CONDITION 2: ANY
PARKER P/N
H61C0552M1 CHECK
VALVE FOUND Do PART 4: CHECK
VALVE REPLACEMENT
-
Do PART 5: RESTORA-
TION
-
(a) It is necessary to do OPTION 2 if the manufacturer's name or part numbers of the installed
check valves cannot be positively identified in the records check.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
11 of 12
REQUIREMENTS BULLETIN 737-29-1127

### Page 12

Group 2-3:
Table 1: Main Landing Gear Wheel Well - Pressure Module Check Valve Replacement
Refer to the listed proce-
dures in SB 737-29-1127
Original Issue or later
approved revisions as an
accepted procedure:
Method of
Compliance
ActionCondition
(b) If the part number cannot be positively identified, it is acceptable to identify the installed
check valve by the manufacturer's name.
Export Controlled ECCN: 9E991
Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 08, 2018
737-29-1127 RB
12 of 12
REQUIREMENTS BULLETIN 737-29-1127

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
