# Boeing Special Attention Service Bulletin 737-32-1448: Revision 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0162; AD 2019-01-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 737-32-1448](https://openairdocs.org/service-documents/boeing/sb-737-32-1448.md)
- Title as filed: SB 737-32-1448 Rev2
- Pages: 226
- PDF: https://openairdocs.org/files/sha256/ba/b5/bab571c8cf4dc9d79ca78fed3d38a3fc98132830c34614147654c41829d73bee
- Page: https://openairdocs.org/service-documents/boeing/sb-737-32-1448/file/bab571c8cf4d

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-32-1448
Original Issue: May 19, 2011
Revision 2: August 02, 2017
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Forward and Aft Trunnion Pin Assemblies
Inspection and Change
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2011 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
1 of 226
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
2 of 226
BOEING SERVICE BULLETIN 737-32-1448
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 7
S u m m a r y  ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 5
A . E f f e c t i v i t y  ............................................... 1 5
1. Airplanes ............................................ 1 5
2 . S p a r e s  A f f e c t e d  ........................................ 3 6
B. Concurrent Requirements ...................................... 3 7
C. Reason ................................................ 3 7
D. Description .............................................. 3 8
E. Compliance .............................................. 4 1
F . A p p r o v a l  ............................................... 6 0
G. Manpower .............................................. 6 1
H. Weight and Balance Changes .................................... 6 7
I. Electrical Load Data ......................................... 6 8
J . R e f e r e n c e s  .............................................. 6 8
1. Existing Data: ......................................... 6 8
2. Data Supplied with this Service Bulletin: ........................... 6 8
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 6 8
K. Publications Affected ........................................ 6 9
L. Interchangeability and Intermixability of Parts ........................... 6 9
M. Software Accomplishment Summary ................................ 6 9
2. MATERIAL INFORMATION ........................................ 7 1
A. Material - Price and Availability ................................... 7 1
B. Industry Support Information .................................... 7 2
C. Parts Necessary for Each Airplane ................................. 7 2
1 . K i t s / P a r t s  ............................................ 7 2
2. Parts and Materials Supplied by the Operator ........................ 7 4
3. Parts Modified and Reidentified ................................ 7 6
4. Parts Removed and Not Replaced .............................. 7 8
D. Parts Necessary to Change Spares ................................. 7 8
E. Special Tooling - Price and Availability ............................... 7 8
F. Special Tooling Necessary to do this Service Bulletin ....................... 7 8
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 7 9
A. GENERAL INFORMATION ..................................... 7 9
B. WORK INSTRUCTIONS ....................................... 8 0
FIGURE 1: LEFT MAIN LANDING GEAR (MLG) OUTER CYLINDER ASSEMBLY AND TRUNNION PIN
ASSEMBLIES INSPECTION .................................. 9 6
FIGURE 2: MAIN LANDING GEAR (MLG) FORWARD TRUNNION PIN ASSEMBLY INSPECTION . 98
FIGURE 3: MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY INSPECTION ..... 9 9
FIGURE 4: RIGHT MAIN LANDING GEAR (MLG) OUTER CYLINDER ASSEMBLY AND TRUNNION PIN
ASSEMBLIES INSPECTION ................................. 1 0 0
FIGURE 5: LEFT MAIN LANDING GEAR (MLG) FORWARD OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 1-2, 4-5] .............................. 1 0 2
FIGURE 6: LEFT MAIN LANDING GEAR (MLG) FORWARD OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 3, 6] ................................ 1 0 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
3 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 4

FIGURE 7: LEFT MAIN LANDING GEAR (MLG) AFT OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 1-2, 4-5] .............................. 1 1 0
FIGURE 8: LEFT MAIN LANDING GEAR (MLG) AFT OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 3, 6] ................................ 1 1 5
FIGURE 9: MAIN LANDING GEAR (MLG) FORWARD TRUNNION PIN CROSS BOLT BUSHING
REPLACEMENT [Group 1, 4] ................................ 1 2 0
FIGURE 10: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE REMOVAL [Group 1-3] .... 1 2 2
FIGURE 11: MAIN LANDING GEAR (MLG) AFT TRUNNION PIN CROSS BOLT BUSHING REPLACEMENT
[Group 1-2, 4-5] ........................................ 1 2 5
FIGURE 12: MAIN LANDING GEAR (MLG) AFT TRUNNION PIN CROSS BOLT BUSHING REPLACEMENT
[Group 3, 6] .......................................... 1 2 7
FIGURE 13: MAIN LANDING GEAR (MLG) AFT TRUNNION BEARING RACE INSPECTION .... 1 2 9
FIGURE 14: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE INSTALLATION [Group 1-2] . 130
FIGURE 15: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE INSTALLATION [Group 3] . . 134
FIGURE 16: LEFT MAIN LANDING GEAR INSTALLATION ....................... 1 3 8
FIGURE 17: RIGHT MAIN LANDING GEAR (MLG) FORWARD OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 1-2, 4-5] .............................. 1 4 1
FIGURE 18: RIGHT MAIN LANDING GEAR (MLG) FORWARD OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 3, 6] ................................ 1 4 5
FIGURE 19: RIGHT MAIN LANDING GEAR (MLG) AFT OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 1-2, 4-5] .............................. 1 4 9
FIGURE 20: RIGHT MAIN LANDING GEAR (MLG) AFT OUTER CYLINDER TRUNNION BUSHING
REPLACEMENT [Group 3, 6] ................................ 1 5 4
FIGURE 21: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE REMOVAL [Group 1-3] .... 1 5 9
FIGURE 22: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE INSTALLATION [Group 1-2] . 162
FIGURE 23: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY, AFT TRUNNION
BEARING BALL AND AFT TRUNNION BEARING RACE INSTALLATION [Group 3] . . 166
FIGURE 24: RIGHT MAIN LANDING GEAR INSTALLATION ...................... 1 7 0
FIGURE 25: MAIN LANDING GEAR TRUNNION HOUSING ASSEMBLY RETAINER AND SEAL INSPECTION
[Group 1-2, 4-5, Configuration 1] ............................... 1 7 3
FIGURE 26: MAIN LANDING GEAR TRUNNION HOUSING ASSEMBLY RETAINER AND SEAL
REPLACEMENT [Group 1-2, 4-5] .............................. 1 7 5
FIGURE 27: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY REMOVAL [Group 4-6]
................................................. 1 7 7
FIGURE 28: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY INSTALLATION [Group
4 - 5 ]  ............................................... 1 8 0
FIGURE 29: LEFT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY INSTALLATION [Group
6 ]  ................................................ 1 8 3
FIGURE 30: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY REMOVAL [Group
4 - 6 ]  ............................................... 1 8 6
FIGURE 31: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY INSTALLATION [Group
4 - 5 ]  ............................................... 1 8 9
FIGURE 32: RIGHT MAIN LANDING GEAR (MLG) AFT TRUNNION PIN ASSEMBLY INSTALLATION [Group
6 ]  ................................................ 1 9 2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
4 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 5

APPENDIX A: FORWARD OUTER CYLINDER TRUNNION BUSHING - MAKE [Group 1-2, 4-5] .... 1 9 5
APPENDIX B: FORWARD OUTER CYLINDER TRUNNION BUSHING - MAKE [Group 3, 6] ...... 1 9 8
APPENDIX C: AFT OUTER CYLINDER TRUNNION BUSHING - MAKE [Group 1-2, 4-5] ........ 2 0 1
APPENDIX D: AFT OUTER CYLINDER TRUNNION BUSHING - MAKE [Group 3, 6] .......... 2 0 4
APPENDIX E: FORWARD TRUNNION PIN CROSS BOLT BUSHING - MAKE [Group 1, 4] ....... 2 0 7
APPENDIX F: AFT TRUNNION PIN CROSS BOLT BUSHING - MAKE [Group 1-2, 4-5] ......... 2 0 9
APPENDIX G: AFT TRUNNION PIN CROSS BOLT BUSHING - MAKE [Group 3, 6] ........... 2 1 1
APPENDIX H: AFT TRUNNION BEARING BALL - CHANGE [Group 1-2] ................. 2 1 3
APPENDIX I: AFT TRUNNION BEARING BALL - CHANGE [Group 3] .................. 2 1 6
APPENDIX J: AFT TRUNNION BEARING RACE - CHANGE [Group 1-2] ................ 2 1 9
APPENDIX K: AFT TRUNNION BEARING RACE - CHANGE [Group 3] .................. 2 2 2
APPENDIX L: DIMENSIONING SYMBOLS ................................. 2 2 5
APPENDIX M: PART DEMAND INTENT ................................... 2 2 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
5 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 6

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
6 of 226
BOEING SERVICE BULLETIN 737-32-1448
BLANK PAGE

### Page 7

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-32-1448Original Issue: May 19, 2011
Revision 2: August 02, 2017
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Forward and Aft Trunnion Pin Assemblies
Inspection and Change
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2016-18-01 is related to this service bulletin.
The effective date of AD 2016-18-01 is October 5, 2016.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service
bulletin mandatory.
Airplane line numbers 3527 through 6510 were added to the service bulletin effectivity, in new groups 4-6.
Effects of this Revision on airplanes on which the Original Issue or Revision 1 was previously done:
ActionConditionGroup
Do a review of maintenance records
or inspect the Main Landing Gear to
find if any of the existing part num-
bers in Paragraph 2.C.3., Parts
Modified and Reidentified are in-
stalled on the airplane, and do addi-
tional actions based on applicable
conditions in accordance with Para-
graph 1.E., Compliance.
Accomplished Service Bulletin 737-
32-1448 Original Issue or Revision
1
1-3
REASON FOR REVISION
This revision is sent to extend the effectivity of this service bulletin to airplane line numbers 3527 through 6510.
The Main Landing Gear (MLG) affected by the change in this service bulletin are rotable parts, and these
airplanes may no longer have their original MLG assemblies due to MLG maintenance activity. The engineering
drawings have been revised to not allow the existing part numbers in Paragraph 2.C.3., Parts Modified and
Reidentified to be installed on airplane line numbers 6511 and on. Instructions have been added to the service
bulletin to do a review of maintenance records or inspect the MLG to see if the currently installed MLG requires
inspection and change in accordance with this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
7 of 226

### Page 8

These sections were changed:
1. In Summary, Background: Added SRP reference.
2. In Summary, Action: Added new step and updated applicability.
3. In the Summary Illustration: Added new groups.
4. In Paragraph 1.A., Effectivity: Changed to include additional airplanes and added new groups.
5. In Paragraph 1.C., Reason: Added revision information and SRP reference.
6. In Paragraph 1.D., Description: Added new step, updated applicability, and added revision information.
7. In Paragraph 1.E., Compliance: Added AD reference and updated the compliance tables.
8. In Paragraph 1.F., Approval: Added AD reference and additional paragraphs.
9. In Paragraph 1.G., Manpower: Updated applicability.
10. In Paragraph 1.J., References: Added AD reference.
11. In Paragraph 1.K., Publications Affected: Added publication.
12. In Paragraph 2., Material Information: Updated applicability.
13. In Paragraph 2.C.3., Parts Modified and Reidentified: Updated table.
14. In Paragraph 3.A., General Information: Added new note.
15. In Paragraph 3.B., Work Instructions: Added new steps and updated applicability.
16. In Figures 5 - 12, 14, 15, 17 - 23, 25, and 26: Updated applicability.
17. Added new Figures 27 - 32.
18. In Appendixes A - G: Updated applicability.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
May 19, 2011Original Issue:
May 29, 2015Revision 1:
August 02, 2017Revision 2:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
8 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 9

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-32-1448Original Issue: May 19, 2011
Revision 2: August 02, 2017
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Forward and Aft Trunnion Pin Assemblies
Inspection and Change
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin is sent to make sure the left and right Main Landing Gear (MLG) forward and aft trunnion
pin assemblies and the components related to the MLG forward and aft trunnion pin assemblies remain
serviceable. Corrosion and chrome damage has been found on some of these components. If this service bulletin
is not done, corrosion and chrome plate damage on these components could cause the MLG forward and aft
trunnion pin assemblies to crack which could result in a MLG collapse.
Several operators have reported heavy corrosion and pitting of the MLG forward and aft trunnion pin assemblies.
Boeing found a number of causes for this damage which include insufficient lubrication, joint contamination and
mixed greases. It was found that the lubrication between the forward and aft trunnion pin assemblies and the
outer cylinder assembly bushings and the lubrication of the aft trunnion bearing ball was not sufficient to prevent
wear and corrosion. It was also found that the clearances between the forward and aft trunnion pin cross bolt
bushings and the cross bolts could affect the rate of wear and corrosion of MLG trunnion pin assemblies. To
correct these problems, Boeing has changed the design of the outer cylinder forward and aft trunnion bushings
to improve lubrication around the outer diameter of the forward and aft trunnion pin assemblies and changed
the design of aft trunnion bearing split ball to add a circumferential lube groove and larger diameter through
holes which improves lubrication around the aft pin at the interface with the aft trunnion bearing. In addition
Boeing has changed the design of the forward and aft trunnion pin cross bolt bushings for the trunnion pins to
reduce relative motion of each pin within the outer cylinder assembly bushings and reduce wear.
Accomplishment of this service bulletin lubricates and inspects existing MLG forward and aft trunnion pin
assemblies at regular intervals to prevent damage and corrosion. Instructions are given to overhaul or replace
damaged or corroded forward and aft trunnion pin assemblies. In addition, instructions are provided to install
new forward and aft trunnion bushings in the MLG outer cylinder assembly, install new trunnion pin cross bolt
bushings in the forward and aft trunnion pins, install a new/changed aft trunnion bearing ball, install a new/changed
aft trunnion bearing race, and install a new forward trunnion pin housing assembly seal and retainer configuration
on applicable airplanes. Installation of the new trunnion bushings in the MLG outer cylinder assembly,
new/changed aft trunnion bearing ball and aft trunnion bearing race are the terminating actions to the repeat
lubrication and repeat inspections given in this service bulletin and will improve grease distribution which will
reduce wear in the joint and prevent corrosion.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
9 of 226

### Page 10

Boeing recommends to do this service bulletin at the same time as 737-32-1376 or 737-32-1402 if applicable.
Boeing Service Related Problem (SRP) 737-SRP-32-0165 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 737NG FTD 32-09001 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-32-0213 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION (PRR 38275-165S)
1. Do a review of maintenance records or inspect the MLG to find if any of the existing part numbers in
Paragraph 2.C.3., Parts Modified and Reidentified are installed on the airplane. If any applicable part
number is found, do the work packages that follow.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 1:
1. Lubricate the forward and aft trunnion pin assemblies on the left and right MLG.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 2:
1. Do a general visual inspection and a detailed inspection if necessary of the forward and aft trunnion
pin assemblies on the left and right MLG.
NOTE: Make sure that you have serviceable trunnion pins available in case the trunnion pins inspected
are found with corrosion or damage and need to be replaced.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
10 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 11

a. If corrosion or damage is found on the forward trunnion pin assembly:
(1) Group 1-2, 4-5, Configuration 1:
Overhaul or replace the forward trunnion pin assembly and install a new forward trunnion pin
housing assembly seal and retainer configuration.
(2) Group 3, 6:
Overhaul or replace the forward trunnion pin assembly.
b. If corrosion or damage is found on the aft trunnion pin assemblies, overhaul or replace the aft
trunnion pin assemblies.
c. If no corrosion or damage is found on the fwd and aft trunnion pin assemblies, no overhaul or
replacement of the forward and aft trunnion pin assemblies is necessary.
2. Lubricate the forward and aft trunnion pin assemblies on the left and right MLG.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 3:
1. Group 1-2, Configuration 1:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace the
forward and aft outer cylinder trunnion bushings, the forward and aft trunnion pin cross bolt bushings,
the aft bearing ball and aft bearing race with new or changed parts and install a new forward trunnion
pin housing assembly seal and retainer configuration.
2. Group 3:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace the
forward and aft outer cylinder trunnion bushings, the forward and aft trunnion pin cross bolt bushings,
the aft bearing ball and aft bearing race with new or changed parts.
3. Group 4-5, Configuration 1:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace the
forward and aft outer cylinder trunnion bushings, and the forward and aft trunnion pin cross bolt bushings
with new or changed parts and install a new forward trunnion pin housing assembly seal and retainer
configuration.
4. Group 6:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace the
forward and aft outer cylinder trunnion bushings, and the forward and aft trunnion pin cross bolt bushings
with new or changed parts.
Group 1-2, 4-5, Configuration 2:
WORK PACKAGE 4:
1. Install a new forward trunnion pin housing assembly seal and retainer configuration.
EFFECTIVITY
737-600/700/700C/800/900/900ER Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected
airplanes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
11 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 12

COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2016-18-01 is related to this service bulletin.
The effective date of AD 2016-18-01 is October 5, 2016.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service
bulletin mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the configuration changes, inspection, and/or overhaul procedures
given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Operators are encouraged to complete the survey provided in APPENDIX M of this service bulletin to help
Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
12 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 13 (OCR)

BOEING SERVICE BULLETIN 737-32-1448
AFT TRUNNION
PIN ASSEMBLY
INBD  INBD
LEFT MAIN LANDING GEAR SHOWN
RIGHT MAIN LANDING GEAR SIMILAR  MAIN LANDING
(LOOKING AFT)  GEAR SUPPORT  MAIN LANDING GEAR NOT SHOWN
BEAM  FOR CLARITY
GROUP 1-2, CONFIGURATION 1, GROUP 3, GROUP 4-5
CONFIGURATION 1, GROUP 6:
WORK PACKAGE 1:
LUBRICATE THE FORWARD AND AFT TRUNNION PIN ASSEMBLIES
FORWARD  TRUNNION PIN  ON THE LEFT AND RIGHT MLG.
ASSEMBLY  GROUP 1-2, CONFIGURATION 1, GROUP 3, GROUP 4-5
CONFIGURATION 1, GROUP 6:
WORK PACKAGE 2:
DO A GENERAL VISUAL INSPECTION AND A DETAILED
NSPECTION IF NECESSARY OF THE FWD AND AFT TRUNNION PIN
ASSEMBLIES ON THE LEFT AND RIGHT MLE
-IF CORROSION OR DAMAGE IS FOUND ON THE FWD AND/OR
AFT TRUN  NION PIN ASSEMBLIES, REPAIR OR REPLACE THE
FWD AND/OR AFT TRUNNION PIN ASSEMBLIES AS APPLICABLE.
GROUP 1-2, CONFIGURATION 1 ONLY:
INSTALL A NEW FORWARD TRUNNION PIN HOUSING ASSEMBLY
-SEAL AND RETAINER CONFIGURATION AS APPLICABLE.
GROUP 4-5 CONFIGURATION 1; GROUP 6
WORK PACKAGE 3:
- REPLACE THE FWD AND AFT OUTER CYLINDER TRUNNION
BUSHINGS, THE FORWARD TRUNNION PIN CROSS BOLT
BUSHINGS (GROUP 4 ONLY) AND AFT TRUNNION PIN CROSS
BOLT BUSHINGS.
MAIN LANDING GEAR NOT SHOWN  GROUP 4-5, CONFIGURATION 1 ONLY
FOR CLARITY  -INSTALL A NEW FORWARD TRUNNION PIN HOUSING ASSEMBLY
SEAL AND RETAINER.
GROUP 1-2, 4-5, CONFIGURATION 2:
WORK PACKAGE 4:
-INSTALL A NEW MLG FORWARD TRUNNION PIN HOUSING  ASSEMBLY, SEAL AND RETAINER.  1984864
Original Issue: May 19, 2011
Revision 2: August 02, 2017  Export Controlled ECCN: 9E991 - BOEING  737-32-1448
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  13 of 226

### Page 14

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
14 of 226
BOEING SERVICE BULLETIN 737-32-1448
BLANK PAGE

### Page 15

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-32-1448
Original Issue: May 19, 2011
Revision 2: August 02, 2017
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Forward and Aft Trunnion Pin Assemblies
Inspection and Change
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-19567 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is applicable to 737-600/700/700C/800/900/900ER Airplanes, line numbers
1 thru 6510, in 6 Groups. The Variable Numbers and Group Information for the applicable airplanes
is given below. Refer to PRR 38275-165S for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
737-600/700 airplanes line number 1 thru 3526, except 737-700
airplanes with a Boeing Business Jet configuration, an Extended
Range configuration, and an Air Early Warning and Control
configuration.
-1
Airplanes with Main Landing Gear that was not changed in
accordance with Work Package 3 of the original issue of this service
bulletin.
1
Airplanes with Main Landing Gear that was changed in accordance
with Work Package 3 of the original issue of this service bulletin.
2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
15 of 226

### Page 16

DESCRIPTIONCONFIGURATIONGROUP
737-700C/800/900 airplanes line number 1 thru 3526 and 737-700
Increased Gross Weight (IGW) airplanes line number 1 thru 3526,
which includes any 737-700 airplanes with a Boeing Business Jet
configuration, an Extended Range configuration, and an Air Early
Warning And Control configuration.
-2
Airplanes with Main Landing Gear that was not changed in
accordance with Work Package 3 of the original issue of this service
bulletin.
1
Airplanes with Main Landing Gear that was changed in accordance
with Work Package 3 of the original issue of this service bulletin.
2
737-900ER airplanes line number 1 thru 3526.-3
737-700 airplanes line number 3527 thru 6510, except 737-700
airplanes with a Boeing Business Jet configuration, an Extended
Range configuration, and an Air Early Warning and Control
configuration.
-4
Airplanes with Main Landing Gear that was not changed in
accordance with Work Package 3 of the original issue of this service
bulletin.
1
Airplanes with Main Landing Gear that was changed in accordance
with Work Package 3 of the original issue of this service bulletin.
2
737-700C/800airplanes line number 3527 thru 6510, and 737-700
Increased Gross Weight (IGW) airplanes line number 3527 and on,
which includes any 737-700 airplanes with a Boeing Business Jet
configuration, an Extended Range configuration, and an Air Early
Warning And Control configuration.
-5
Airplanes with Main Landing Gear that was not changed in
accordance with Work Package 3 of the original issue of this service
bulletin.
1
Airplanes with Main Landing Gear that was changed in accordance
with Work Package 3 of the original issue of this service bulletin.
2
737-900ER airplanes line number 3527 thru 6510.-6
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
16 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 17

GroupVariable Number
1YA001 - YA099
1YA101 - YA199
1YA201 - YA211
1YA221
1YA231 - YA242
1YA251 - YA256
1YA271 - YA272
1YA291
1YA301 - YA302
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
1YA721 - YA722
1YA731 - YA734
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
17 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 18

GroupVariable Number
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB635
4YB636
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
18 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 19

GroupVariable Number
1YB881 - YB893
1YB901 - YB903
1YB911
1YB961 - YB974
4YB975
1YB981
1YB986 - YB996
4YB997 - YB998
2YC001 - YC030
2YC051 - YC084
2YC091 - YC095
2YC101 - YC104
2YC111 - YC113
2YC121
2YC126 - YC127
2YC136 - YC141
2YC146 - YC147
2YC151 - YC156
2YC166 - YC171
2YC176 - YC179
2YC186 - YC190
2YC201 - YC203
2YC206 - YC207
2YC301 - YC305
2YC321 - YC387
2YC391 - YC394
2YC396
2YC401 - YC417
2YC421 - YC422
2YC426 - YC428
2YC436 - YC439
2YC441 - YC448
2YC451 - YC455
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
19 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 20

GroupVariable Number
2YC459
2YC461 - YC467
2YC471 - YC499
2YC501 - YC526
2YC571 - YC583
2YC587 - YC589
2YC591 - YC593
2YC601 - YC655
2YC681 - YC696
2YC701 - YC715
2YC720 - YC725
2YC727 - YC752
2YC761 - YC770
2YC781 - YC793
2YC801 - YC892
2YC901 - YC907
2YC921 - YC922
2YC931 - YC932
2YC941 - YC951
2YC971 - YC978
2YC981 - YC983
2YD001 - YD007
2YD021 - YD025
2YD041 - YD057
2YD081 - YD084
2YD101 - YD113
5YD114 - YD117
2YD121 - YD126
2YD151 - YD159
2YD171 - YD172
2YD201 - YD203
2YD206 - YD209
2YD216 - YD219
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
20 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 21

GroupVariable Number
2YD251 - YD254
2YD256 - YD257
2YD261
2YD301 - YD334
2YD391
2YD401 - YD410
2YD412 - YD417
5YD418 - YD422
2YD481 - YD485
2YD491 - YD499
2YD501 - YD512
2YD531 - YD535
2YD541 - YD547
2YD561 - YD564
2YD571 - YD572
2YD591 - YD595
2YD601 - YD612
2YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
2YF001 - YF011
2YF021 - YF049
2YF051 - YF065
5YF066 - YF080
2YF086 - YF087
2YF106 - YF107
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
21 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 22

GroupVariable Number
2YF111 - YF114
2YF116 - YF119
2YF121 - YF128
5YF129 - YF132
2YF176 - YF178
2YF191 - YF192
2YF201 - YF276
2YF401 - YF402
2YF431 - YF432
5YF436 - YF437
2YF441 - YF442
2YF451 - YF460
2YF501 - YF599
5YF601 - YF685
5YF691 - YF695
2YF701 - YF707
2YF801 - YF803
5YF804 - YF805
2YF831 - YF832
2YF836 - YF838
5YF871 - YF872
2YF901 - YF905
2YF921 - YF927
5YF928
2YF951
5YF952 - YF954
2YG001 - YG044
2YG061 - YG064
2YG066 - YG089
2YG091 - YG099
2YG101 - YG104
2YG111 - YG114
2YG116 - YG128
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
22 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 23

GroupVariable Number
5YG129 - YG146
2YG201 - YG205
2YG211 - YG214
2YG221 - YG224
2YG251 - YG252
2YG501 - YG511
5YG512 - YG515
2YG601 - YG602
2YG701
2YG711
5YG721 - YG722
3YH001 - YH012
3YH031 - YH055
3YH071 - YH078
6YH079 - YH080
3YH101 - YH132
3YH201 - YH202
3YH206 - YH207
3YH301 - YH306
6YH307
3YH321 - YH322
6YH501 - YH542
6YH551 - YH594
6YH601 - YH606
6YH611 - YH620
6YH631 - YH632
6YH636 - YH637
6YH641
6YH681 - YH685
6YH701 - YH755
6YH801 - YH881
6YH901 - YH908
6YH911 - YH915
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
23 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 24

GroupVariable Number
6YH951 - YH952
2YJ001 - YJ013
2YJ021
2YJ471 - YJ480
2YJ501 - YJ517
2YJ531 - YJ579
2YJ591 - YJ599
2YJ631 - YJ632
2YJ671 - YJ694
2YJ801 - YJ867
2YJ871 - YJ880
2YJ901 - YJ904
2YJ908 - YJ929
2YJ931 - YJ937
2YJ941 - YJ956
2YJ961
2YJ976 - YJ977
2YK001 - YK007
2YK101 - YK104
2YK111 - YK112
2YK121 - YK122
2YK131 - YK133
2YK136 - YK139
2YK141 - YK142
2YK146 - YK148
2YK151 - YK154
2YK161 - YK167
2YK171
2YK176 - YK177
2YK186
2YK191
2YK196
2YK201 - YK202
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
24 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 25

GroupVariable Number
2YK301 - YK314
2YK321 - YK340
2YK361 - YK378
2YK401 - YK406
2YK426 - YK427
2YK431 - YK450
2YK456 - YK467
2YK471 - YK473
2YK476
5YK478
2YK480 - YK487
2YK491
5YK492 - YK493
2YK495 - YK498
5YK499
2YK511 - YK516
2YK521 - YK530
2YK551 - YK571
2YK576 - YK577
2YK580 - YK585
2YK601 - YK602
2YK606 - YK607
2YK611 - YK616
2YK621 - YK634
2YK641 - YK644
2YK651 - YK665
2YK671 - YK672
2YK676 - YK677
2YK681 - YK686
2YK691
5YK695 - YK699
2YK701 - YK713
2YK716 - YK719
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
25 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 26

GroupVariable Number
2YK721 - YK741
2YK751 - YK770
2YK776 - YK778
2YK781 - YK785
2YK791 - YK792
2YK796 - YK797
2YK801 - YK899
2YK901 - YK912
2YK918 - YK919
2YK921 - YK928
5YK929
2YK941 - YK959
5YK960
2YK961 - YK996
5YK997 - YK999
2YL001 - YL005
2YL011 - YL016
2YL021 - YL024
2YL051 - YL052
2YL056 - YL057
2YL061
2YL066 - YL069
2YL076 - YL077
2YL101 - YL136
5YL137
2YL201 - YL226
5YL227 - YL237
5YL241 - YL242
2YL271 - YL272
2YL281 - YL284
2YL301 - YL303
2YL311 - YL314
2YL316 - YL321
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
26 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 27

GroupVariable Number
2YL351 - YL353
2YL371 - YL374
2YL401
2YL421 - YL429
2YL431 - YL444
2YL461 - YL478
2YL501 - YL509
2YL531 - YL534
2YL541 - YL544
5YL545 - YL551
2YL561 - YL569
5YL570 - YL579
2YL591 - YL598
2YL601 - YL606
2YL611 - YL612
2YL616 - YL617
2YL621
2YL626
2YL631 - YL634
2YL636 - YL637
2YL661 - YL664
2YL676 - YL681
5YL682 - YL690
2YL691
2YL696 - YL697
2YL701 - YL706
5YL707
2YL731
2YL751 - YL752
2YL756 - YL757
2YL761 - YL779
5YL780
2YL796 - YL797
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
27 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 28

GroupVariable Number
2YL801 - YL815
2YL901 - YL910
2YL921 - YL940
2YL951 - YL968
1YM101 - YM103
1YM201 - YM242
4YM243 - YM244
1YM251 - YM299
1YM301 - YM398
4YM399
4YM401 - YM415
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
1YM581 - YM582
1YM591 - YM599
1YM631 - YM634
1YM641 - YM652
1YM671 - YM674
1YM691 - YM698
4YM699
1YM701 - YM710
1YM761 - YM765
4YM771 - YM779
1YN001 - YN016
1YN021 - YN024
1YN061
1YN071 - YN082
1YN091 - YN092
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
28 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 29

GroupVariable Number
1YN101 - YN112
1YN121
4YN126
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
1YN261
1YN501
4YN531 - YN534
4YN551 - YN566
4YN581 - YN585
4YN591 - YN593
4YN601 - YN606
4YN651 - YN653
4YN661 - YN663
4YN671 - YN672
4YN701 - YN702
4YN741 - YN746
4YN756 - YN758
2YQ001 - YQ003
2YQ011 - YQ017
5YQ018 - YQ021
2YQ026 - YQ027
5YQ028 - YQ029
2YQ036 - YQ042
5YQ043 - YQ045
2YQ201
5YQ202 - YQ207
2YQ231
2YQ241 - YQ242
5YQ243 - YQ251
5YQ281 - YQ284
2YQ291 - YQ295
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
29 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 30

GroupVariable Number
5YQ296
5YQ301 - YQ302
5YQ321 - YQ324
5YQ331 - YQ334
5YQ346 - YQ347
5YQ351 - YQ365
5YQ371
2YQ401 - YQ403
5YQ451 - YQ454
5YQ456
5YQ461
5YQ471
5YQ501 - YQ520
2YR001 - YR005
5YR006 - YR050
2YR051 - YR053
5YR054 - YR098
2YR101
5YR102 - YR105
2YR111 - YR112
5YR113 - YR124
5YR126 - YR144
2YR166
5YR167 - YR182
5YR186 - YR198
2YR201 - YR203
5YR204 - YR211
2YR231 - YR232
5YR233 - YR294
5YR296 - YR297
5YR301 - YR334
5YR338 - YR341
5YR361 - YR366
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
30 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 31

GroupVariable Number
5YR371 - YR373
5YR376 - YR377
5YR381 - YR382
5YR386 - YR388
5YR391
5YR396 - YR399
5YR401 - YR405
5YR411 - YR413
5YR416 - YR418
5YR421 - YR424
5YR426 - YR455
5YR457 - YR499
5YR501 - YR506
5YR511 - YR520
5YR526 - YR544
5YR546 - YR551
5YR556 - YR562
5YR571 - YR582
5YR591 - YR592
5YR601 - YR605
5YR616 - YR658
5YR661 - YR663
5YR671 - YR673
5YR676 - YR678
5YR681 - YR682
5YR701 - YR769
5YR771 - YR799
5YR801 - YR823
5YR831 - YR838
5YR841 - YR899
5YR901 - YR903
5YR931 - YR934
5YR938 - YR944
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
31 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 32

GroupVariable Number
5YR951 - YR998
5YS001 - YS002
5YS006 - YS009
5YS031 - YS032
5YS051 - YS073
5YS101 - YS120
5YS126 - YS142
5YS146 - YS160
5YS166 - YS194
5YS196 - YS197
5YS201 - YS209
5YS221 - YS225
5YS231 - YS236
5YS271 - YS288
5YS301 - YS348
5YS351 - YS378
5YS381 - YS383
5YS401
5YS451
5YS456 - YS457
5YS462 - YS465
5YS467
5YS501 - YS502
5YS506
5YS511 - YS518
5YS531
5YS536 - YS538
5YS541 - YS542
5YS546
5YS551 - YS556
5YS561 - YS578
5YS581 - YS595
5YS601 - YS690
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
32 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 33

GroupVariable Number
5YS701 - YS712
5YS721 - YS762
5YS771 - YS780
5YS806 - YS810
5YS816 - YS818
5YS823 - YS825
5YS851 - YS862
5YS876
5YS881 - YS883
5YS896 - YS897
5YS901 - YS909
5YS911 - YS957
5YS961 - YS974
5YS976 - YS977
5YS981 - YS987
5YS991 - YS998
5YT001 - YT004
5YT006
5YT026 - YT027
5YT031 - YT032
5YT036 - YT038
5YT061 - YT068
5YT101 - YT122
5YT126 - YT138
5YT176 - YT185
5YT191
5YT196 - YT199
5YT201
5YT206 - YT207
5YT211 - YT213
5YT251 - YT299
5YT301 - YT307
5YT311 - YT312
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
33 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 34

GroupVariable Number
5YT321 - YT354
5YT371 - YT372
5YT381
5YT391 - YT396
5YT401 - YT403
5YT411 - YT417
5YT427
5YT461 - YT477
5YT491 - YT492
5YT501 - YT521
5YT551 - YT552
5YT556 - YT563
5YT565
5YT571 - YT576
5YT601 - YT606
5YT701 - YT708
5YT761 - YT781
5YT791 - YT793
5YT796 - YT797
5YT801 - YT804
5YT811 - YT813
5YT826 - YT827
5YT831 - YT832
5YT841 - YT846
5YT851 - YT852
5YT856 - YT863
5YT885 - YT887
5YT891 - YT895
5YT901 - YT975
6YU001 - YU060
6YU201 - YU216
6YU301 - YU310
5YV001 - YV004
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
34 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 35

GroupVariable Number
5YV006 - YV012
5YV021 - YV023
5YV030 - YV033
5YV037 - YV038
5YV041 - YV042
5YV045 - YV047
5YV051 - YV054
5YV081
5YV083 - YV084
5YV097 - YV099
5YV101 - YV146
5YV201
5YV251 - YV252
5YV256 - YV257
5YV301 - YV312
5YV351 - YV368
5YV381 - YV388
5YV391 - YV394
5YV401
5YV411
5YV431 - YV433
5YV441 - YV450
5YV461 - YV462
5YV501 - YV504
5YV521
5YV571 - YV581
5YV601 - YV605
5YV651 - YV664
5YV695 - YV696
5YV711
5YV722 - YV731
5YV741 - YV761
5YV781 - YV787
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
35 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 36

GroupVariable Number
5YV801 - YV811
5YV881 - YV883
5YV901 - YV910
5YV923
5YV971 - YV980
5YW001
5YW011 - YW098
5YW226 - YW240
5YW245 - YW249
5YW261
5YW263
5YW267 - YW278
5YW283 - YW285
5YW292 - YW294
5YW356 - YW358
5YW361 - YW362
5YW371 - YW386
5YW401 - YW404
5YW451 - YW452
5YW471 - YW472
5YW491
5YW551 - YW553
5YW585
5YW595
5YW881
5YW891 - YW893
5YW906 - YW907
5YW916 - YW918
5YW971 - YW974
2. Spares Affected
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
36 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 37

B. Concurrent Requirements
None.
C. Reason
This service bulletin is sent to make sure the left and right Main Landing Gear (MLG) forward and aft
trunnion pin assemblies and the components related to the MLG forward and aft trunnion pin assemblies
remain serviceable. Corrosion and chrome damage has been found on some of these components. If
this service bulletin is not done, corrosion and chrome plate damage on these components could cause
the MLG forward and aft trunnion pin assemblies to crack which could result in a MLG collapse.
Several operators have reported heavy corrosion and pitting of the MLG forward and aft trunnion pin
assemblies. Boeing found a number of causes for this damage which include insufficient lubrication,
joint contamination and mixed greases. It was found that the lubrication between the forward and aft
trunnion pin assemblies and the outer cylinder assembly bushings and the lubrication of the aft trunnion
bearing ball was not sufficient to prevent wear and corrosion. It was also found that the clearances
between the forward and aft trunnion pin cross bolt bushings and the cross bolts could affect the rate
of wear and corrosion of MLG trunnion pin assemblies. To correct these problems, Boeing has changed
the design of the outer cylinder forward and aft trunnion bushings to improve lubrication around the
outer diameter of the forward and aft trunnion pin assemblies and changed the design of aft trunnion
bearing split ball to add a circumferential lube groove and larger diameter through holes which improves
lubrication around the aft pin at the interface with the aft trunnion bearing. In addition Boeing has
changed the design of the forward and aft trunnion pin cross bolt bushings for the trunnion pins to
reduce relative motion of each pin within the outer cylinder assembly bushings and reduce wear.
Accomplishment of this service bulletin lubricates and inspects existing MLG forward and aft trunnion
pin assemblies at regular intervals to prevent damage and corrosion. Instructions are given to overhaul
or replace damaged or corroded forward and aft trunnion pin assemblies. In addition, instructions are
provided to install new forward and aft trunnion bushings in the MLG outer cylinder assembly, install
new trunnion pin cross bolt bushings in the forward and aft trunnion pins, install a new/changed aft
trunnion bearing ball, install a new/changed aft trunnion bearing race, and install a new forward trunnion
pin housing assembly seal and retainer configuration on applicable airplanes. Installation of the new
trunnion bushings in the MLG outer cylinder assembly, new/changed aft trunnion bearing ball and aft
trunnion bearing race are the terminating actions to the repeat lubrication and repeat inspections given
in this service bulletin and will improve grease distribution which will reduce wear in the joint and prevent
corrosion.
Boeing recommends to do this service bulletin at the same time as 737-32-1376 or 737-32-1402 if
applicable.
Boeing Service Related Problem (SRP) 737-SRP-32-0165 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 737NG FTD 32-09001 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737NG-32-0213 is related to this service bulletin.
Revision 1 is sent to add Work Package 4 for Group 1 and Group 2 airplanes that have previously
changed the Main Landing gear (MLG) trunnion pin assemblies in accordance with Work Package 3.
It provides new figures to replace the seal and retainer configuration for the trunnion housing assembly.
This information has also been added to Work Package 3 for operators that have not previously changed
the MLG trunnion pin assemblies. In addition, 737-700 Increased Gross Weight (IGW) airplanes, which
includes any 737-700 airplanes with a Boeing Business Jet (BBJ) configuration, an Extended Range
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
37 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 38

(ER) configuration, and an Air Early Warning And Control (AEW&C) configuration are moved from
Group 1 to Group 2 as they have a MLG configuration that is similar to 737-800 airplanes. The use of
Component Maintenance Manual (CMM) and Standard Overhaul Practices Manual (SOPM) procedures
that have been identified as critical in this service bulletin are mandated. Instructions to accomplish
these critical procedures now use the terminology "in accordance with". Revision 1 also clarifies the
lubrication procedure to show only the applicable lubrication locations and changes the MLG support
beam part marking information.
The data given in Information Notice 737-32-1448 IN 01 is included in Revision 1.
Revision 2 is sent to extend the effectivity of this service bulletin to airplane line numbers 3527 through
6510. The Main Landing Gear (MLG) affected by the change in this service bulletin are rotable parts,
and these airplanes may no longer have their original MLG assemblies due to MLG maintenance
activity. The engineering drawings have been revised to not allow the existing part numbers in Paragraph
2.C.3., Parts Modified and Reidentified to be installed on airplane line numbers 6511 and on. Instructions
have been added to the service bulletin to do a review of maintenance records or inspect the MLG to
see if the currently installed MLG requires inspection and change in accordance with this service bulletin.
D. Description
1. Do a review of maintenance records or inspect the MLG to find if any of the existing part numbers
in Paragraph 2.C.3., Parts Modified and Reidentified are installed on the airplane. If any applicable
part number is found, do the work packages that follow.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 1:
1. Lubricate the forward and aft trunnion pin assemblies on the left and right MLG.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 2:
1. Do a general visual inspection and a detailed inspection if necessary of the forward and aft trunnion
pin assemblies on the left and right MLG.
NOTE: Make sure that you have serviceable trunnion pins available in case the trunnion pins
inspected are found with corrosion or damage and need to be replaced.
a. If corrosion or damage is found on the forward trunnion pin assembly:
(1) Group 1-2, 4-5, Configuration 1:
Overhaul or replace the forward trunnion pin assembly and install a new forward trunnion
pin housing assembly seal and retainer configuration.
(2) Group 3, 6:
Overhaul or replace the forward trunnion pin assembly.
b. If corrosion or damage is found on the aft trunnion pin assemblies, overhaul or replace the
aft trunnion pin assemblies.
c. If no corrosion or damage is found on the fwd and aft trunnion pin assemblies, no overhaul
or replacement of the forward and aft trunnion pin assemblies is necessary.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
38 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 39

2. Lubricate the forward and aft trunnion pin assemblies on the left and right MLG.
Group 1-2, Configuration 1; Group 3; Group 4-5, Configuration 1; Group 6:
WORK PACKAGE 3:
1. Group 1-2, Configuration 1:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace
the forward and aft outer cylinder trunnion bushings, the forward and aft trunnion pin cross bolt
bushings, the aft bearing ball and aft bearing race with new or changed parts and install a new
forward trunnion pin housing assembly seal and retainer configuration.
2. Group 3:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace
the forward and aft outer cylinder trunnion bushings, the forward and aft trunnion pin cross bolt
bushings, the aft bearing ball and aft bearing race with new or changed parts.
3. Group 4-5, Configuration 1:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace
the forward and aft outer cylinder trunnion bushings, and the forward and aft trunnion pin cross
bolt bushings with new or changed parts and install a new forward trunnion pin housing assembly
seal and retainer configuration.
4. Group 6:
As terminating action to repeat lubrications and repeat inspections given in compliance, replace
the forward and aft outer cylinder trunnion bushings, and the forward and aft trunnion pin cross
bolt bushings with new or changed parts.
Group 1-2, 4-5, Configuration 2:
WORK PACKAGE 4:
1. Install a new forward trunnion pin housing assembly seal and retainer configuration.
Effects of Revision 1 on airplanes on which the original issue was previously done:
ActionConditionGroup
Operators must continue to do the
repeat lubrication and MLG forward
and aft trunnion inspections in accor-
dance with Paragraph 1.E., Compli-
ance until new and improved parts
are installed.
Previously accomplished the lubrica-
tion and MLG forward and aft trun-
nion inspections in accordance with
Paragraph 3.B., Work Instructions,
Work Package 1 and 2 of the origi-
nal issue of this service bulletin.
Group 1, Configuration 1
Install a new forward trunnion pin
housing assembly seal and retainer
configuration in accordance with
Paragraph 3.B., Work Instructions,
Work Package 4.
Previously accomplished the MLG
trunnion pin assemblies change in
accordance with Paragraph 3.B.,
Work Instructions, Work Package 3
and 2 of the original issue of this
service bulletin.
Group 1, Configuration 2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
39 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 40

ActionConditionGroup
Operators must continue to do the
repeat lubrication and MLG forward
and aft trunnion inspections in accor-
dance with Paragraph 1.E., Compli-
ance until new and improved parts
are installed.
Previously accomplished the lubrica-
tion and MLG forward and aft trun-
nion inspections in accordance with
Paragraph 3.B., Work Instructions,
Work Package 1 and 2 of the origi-
nal issue of this service bulletin.
Group 2, Configuration 1
Install a new forward trunnion pin
housing assembly seal and retainer
configuration in accordance with
Paragraph 3.B., Work Instructions,
Work Package 4.
Previously accomplished the MLG
trunnion pin assemblies change in
accordance with Paragraph 3.B.,
Work Instructions, Work Package 3
and 2 of the original issue of this
service bulletin.
Group 2, Configuration 2
Operators must continue to do the
repeat lubrication and MLG forward
and aft trunnion inspections in accor-
dance with Paragraph 1.E., Compli-
ance until new and improved parts
are installed. (a)
Previously accomplished the lubrica-
tion and MLG forward and aft trun-
nion inspections in accordance with
Paragraph 3.B., Work Instructions,
Work Package 1 and 2 of the origi-
nal issue of this service bulletin.
Group 3
(a) MLG forward trunnion pin housing assembly seal and retainer replacement is not necessary.
Effects of Revision 2 on airplanes on which the Original Issue or Revision 1 was previously done:
ActionConditionGroup
Do a review of maintenance records
or inspect the MLG to find if any of
the existing part numbers in Para-
graph 2.C.3., Parts Modified and
Reidentified are installed on the air-
plane, and do additional actions
based on applicable conditions in
accordance with Paragraph 1.E.,
Compliance.
Accomplished Service Bulletin 737-
32-1448 Original Issue or Revision
1
1-3
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
133, 134, 551, 651, 734, 744737-600, 737-700
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
40 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 41

Group 2:
Affected Maintenance Zones
ZoneModel
133, 134, 551, 651, 734, 744737-700, 737-700C, 737-800,
737-900
Group 3, 6:
Affected Maintenance Zones
ZoneModel
133, 134, 551, 651, 734, 744737-900ER
Group 4:
Affected Maintenance Zones
ZoneModel
133, 134, 551, 651, 734, 744737-700
Group 5:
Affected Maintenance Zones
ZoneModel
133, 134, 551, 651, 734, 744737-700, 737-700C, 737-800
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2016-18-01 is related to this service
bulletin. The effective date of AD 2016-18-01 is October 5, 2016.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive
related to this service bulletin. The Airworthiness Directive will make the compliance tasks and times
given in this service bulletin mandatory.
Boeing recommends that the inspection, change and/or overhaul given in this service bulletin be done
within the time limits given in the table below.
Accomplish the required actions, based on the applicable conditions in Tables 1 through 5, in accordance
with Paragraph 3. Accomplishment Instructions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
41 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 42

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin. (d)
OPTION 1: Do a review
of maintenance records
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
All airplanes
OPTION 2: Inspect the
MLG forward and aft
trunnion pin assemblies
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
---No further action is re-
quired.
No existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
42 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 43

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
30 days. See foot-
note (a)
Within 30 days
since the date of
issuance of the
original stan-
dard airworthi-
ness certificate
or date of is-
suance of the
original export
certificate of air-
worthiness.
Within 30 days
after the effec-
tive date of AD
2016-18-01.
Lubricate the applicable
MLG forward and aft
trunnion pin assemblies
in accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 1.
Any existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
18 months. See
footnote (a)
Within 60
months since
the date of is-
suance of the
original stan-
dard airworthi-
ness certificate
or date of is-
suance of the
original export
certificate of air-
worthiness, or
within 60
months from the
date of MLG in-
stallation after
overhaul
whichever oc-
curs later.
Within 6 months
after the effec-
tive date of AD
2016-18-01.
Do a general visual in-
spection of the applicable
MLG forward and aft
trunnion pin assemblies
with the MLG not re-
moved for signs of corro-
sion and chrome plating
damage in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Lubricate the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
No sign of corrosion or
chrome plating damage
found during general visual
inspection of the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
43 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 44

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Do a detailed inspection
of the applicable MLG
forward trunnion pin as-
sembly and do a part
number inspection of the
MLG forward trunnion pin
housing assembly seal
and retainer in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG forward
trunnion pin assembly dur-
ing general visual inspec-
tion in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2
with a new seal and re-
tainer configuration.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
AndAnd
Lubricate the applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
44 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 45

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
No overhaul or replace-
ment of the MLG forward
trunnion pin assembly is
necessary. Lubricate the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2
with a new seal and re-
tainer configuration. See
footnote (b)
And
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
45 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 46

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
See footnote (b)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG aft
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG aft trun-
nion pin assemblies during
general visual inspection in
accordance with Paragraph
3.B., Work Instructions
Work Package 2.
--Before further
flight.
No overhaul or replace-
ment of the MLG aft trun-
nion pin assembly is nec-
essary. Lubricate the ap-
plicable MLG aft trunnion
pin assembly in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
Overhaul or replace the
applicable MLG aft trun-
nion pin assembly in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 2. See
footnote (c)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
46 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 47

Group 1-2, Configuration 1:
TABLE 1: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 10 years
after the effec-
tive date of AD
2016-18-01.
Do the MLG trunnion pin
assembly changes in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 3. See
footnote (a)
All airplanes
And
Inspect the left and right
MLG forward trunnion pin
housing assembly seal
and retainer for part
numbers in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 3.
--Before further
flight.
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 3
with a new seal and re-
tainer configuration.
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
3.
---No replacement of the
MLG forward trunnion pin
housing assembly seal
and retainer is necessary.
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 3.
(a) Installation of the new and improved parts in accordance with Work Package 3 is the terminating action
for the repeat lubrication and repeat inspection tasks given in this service bulletin.
(b) Forward trunnion pins can be overhauled at the operators approved maintenance facility in accordance
with CMM 57-15-01 "Repair 12-3 and Repair 12-4" revision 30, dated July 01, 2014 or later Boeing ap-
proved revisions that are published on myboeingfleet.
(c) Aft trunnion pins can be overhauled at the operators approved maintenance facility in accordance with
CMM 32-11-09 "Repair 3-1" revision 23, dated March 01, 2014 or later Boeing approved revisions that
are published on myboeingfleet.
(d) If any existing part number from Paragraph 2.C.3., Parts Modified and Reidentified is installed on the
airplane, make sure that the existing part is not used on any other airplane until the part is modified and
reidentified in accordance with Work Package 3 of this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
47 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 48

Group 3:
TABLE 2: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin. (d)
OPTION 1: Do a review
of maintenance records
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
All airplanes
OPTION 2: Inspect the
MLG forward and aft
trunnion pin assemblies
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
---No further action is re-
quired.
No existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
48 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 49

Group 3:
TABLE 2: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
30 days. See foot-
note (a)
Within 30 days
since the date of
issuance of the
original stan-
dard airworthi-
ness certificate
or date of is-
suance of the
original export
certificate of air-
worthiness.
Within 30 days
after the effec-
tive date of AD
2016-18-01.
Lubricate the applicable
MLG forward and aft
trunnion pin assemblies
in accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 1.
Any existing part number
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
18 months. See
footnote (a)
Within 60
months since
the date of is-
suance of the
original stan-
dard airworthi-
ness certificate
or date of is-
suance of the
original export
certificate of air-
worthiness, or
within 60
months from the
date of MLG in-
stallation after
overhaul
whichever oc-
curs later.
Within 6 months
after the effec-
tive date of AD
2016-18-01.
Do a general visual in-
spection of the applicable
MLG forward and aft
trunnion pin assemblies
with the MLG not re-
moved for signs of corro-
sion and chrome plating
damage in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Lubricate the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
No sign of corrosion or
chrome plating damage
found during general visual
inspection of the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
49 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 50

Group 3:
TABLE 2: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Do a detailed inspection
of the applicable MLG
forward trunnion pin as-
sembly in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG forward
trunnion pin assembly dur-
ing general visual inspec-
tion in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
No overhaul or replace-
ment of the MLG forward
trunnion pin assembly is
necessary. Lubricate the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
See footnote (b)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG aft
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG aft trun-
nion pin assemblies during
general visual inspection in
accordance with Paragraph
3.B., Work Instructions
Work Package 2.
--Before further
flight.
No overhaul or replace-
ment of the MLG aft trun-
nion pin assembly is nec-
essary. Lubricate the ap-
plicable MLG aft trunnion
pin assembly in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
50 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 51

Group 3:
TABLE 2: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Overhaul or replace the
applicable MLG aft trun-
nion pin assembly in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 2. See
footnote (c)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Within 10 years
after the effec-
tive date of AD
2016-18-01.
Do the MLG trunnion pin
assembly changes in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 3. See
footnote (a)
All airplanes
(a) Installation of the new and improved parts in accordance with Work Package 3 is the terminating action
for the repeat lubrication and repeat inspection tasks given in this service bulletin.
(b) Forward trunnion pins can be overhauled at the operators approved maintenance facility in accordance
with CMM 57-15-01 "Repair 12-3 and Repair 12-4" revision 30, dated July 01, 2014 or later Boeing ap-
proved revisions that are published on myboeingfleet.
(c) Aft trunnion pins can be overhauled at the operators approved maintenance facility in accordance with
CMM 32-11-09 "Repair 3-1" revision 23, dated March 01, 2014 or later Boeing approved revisions that
are published on myboeingfleet.
(d) If any existing part number from Paragraph 2.C.3., Parts Modified and Reidentified is installed on the
airplane, make sure that the existing part is not used on any other airplane until the part is modified and
reidentified in accordance with Work Package 3 of this service bulletin.
Group 1-2, Configuration 2:
TABLE 3: MAIN LANDING GEAR (MLG) TRUNNION PIN HOUSING ASSEMBLY SEAL AND RETAIN-
ER CHANGE
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 10 years af-
ter the effective
date of AD 2016-
18-01.
Replace the MLG forward
trunnion pin housing as-
sembly seal, support ring
assembly, and retainer in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 4.
Airplanes with Main Land-
ing Gear that was changed
in accordance with Work
Package 3 of the original
issue of this service bul-
letin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
51 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 52

Group 4-5, Configuration 1:
TABLE 4: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin. (d)
OPTION 1: Do a review
of maintenance records
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
All airplanes
OPTION 2: Inspect the
MLG forward and aft
trunnion pin assemblies
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
---No further action is re-
quired.
No existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
30 days. See foot-
note (a)
-Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin.
Lubricate the applicable
MLG forward and aft
trunnion pin assemblies
in accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 1.
Any existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
18 months. See
footnote (a)
-Within 6 months
after the Revi-
sion 2 date of
this service bul-
letin.
Do a general visual in-
spection of the applicable
MLG forward and aft
trunnion pin assemblies
with the MLG not re-
moved for signs of corro-
sion and chrome plating
damage in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
52 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 53

Group 4-5, Configuration 1:
TABLE 4: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Lubricate the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
No sign of corrosion or
chrome plating damage
found during general visual
inspection of the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG
forward trunnion pin as-
sembly and do a part
number inspection of the
MLG forward trunnion pin
housing assembly seal
and retainer in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG forward
trunnion pin assembly dur-
ing general visual inspec-
tion in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2
with a new seal and re-
tainer configuration.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
AndAnd
Lubricate the applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
53 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 54

Group 4-5, Configuration 1:
TABLE 4: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
No overhaul or replace-
ment of the MLG forward
trunnion pin assembly is
necessary. Lubricate the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2
with a new seal and re-
tainer configuration. See
footnote (b)
And
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
54 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 55

Group 4-5, Configuration 1:
TABLE 4: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
See footnote (b)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
And
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG aft
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG aft trun-
nion pin assemblies during
general visual inspection in
accordance with Paragraph
3.B., Work Instructions
Work Package 2.
--Before further
flight.
No overhaul or replace-
ment of the MLG aft trun-
nion pin assembly is nec-
essary. Lubricate the ap-
plicable MLG aft trunnion
pin assembly in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
Overhaul or replace the
applicable MLG aft trun-
nion pin assembly in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 2. See
footnote (c)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
55 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 56

Group 4-5, Configuration 1:
TABLE 4: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 10 years
after the Revi-
sion 2 date of
this service bul-
letin.
Do the MLG trunnion pin
assembly changes in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 3. See
footnote (a)
All airplanes
And
Inspect the left and right
MLG forward trunnion pin
housing assembly seal
and retainer for part
numbers in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 3.
--Before further
flight.
Replace the MLG forward
trunnion pin housing as-
sembly seal, retainer, and
support ring assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 3
with a new seal and re-
tainer configuration.
MLG forward trunnion pin
housing assembly seal P/N
S38624 and retainer P/N
161A1194-1 found during
inspection in accordance
with Paragraph 3.B., Work
Instructions, Work Package
3.
---No replacement of the
MLG forward trunnion pin
housing assembly seal
and retainer is necessary.
MLG forward trunnion pin
housing assembly seal P/N
5649-0615-369 and retain-
er P/N 161A1194-3 found
during inspection in accor-
dance with Paragraph 3.B.,
Work Instructions, Work
Package 3.
(a) Installation of the new and improved parts in accordance with Work Package 3 is the terminating action
for the repeat lubrication and repeat inspection tasks given in this service bulletin.
(b) Forward trunnion pins can be overhauled at the operators approved maintenance facility in accordance
with CMM 57-15-01 "Repair 12-3 and Repair 12-4" revision 30, dated July 01, 2014 or later Boeing ap-
proved revisions that are published on myboeingfleet.
(c) Aft trunnion pins can be overhauled at the operators approved maintenance facility in accordance with
CMM 32-11-09 "Repair 3-1" revision 23, dated March 01, 2014 or later Boeing approved revisions that
are published on myboeingfleet.
(d) If any existing part number from Paragraph 2.C.3., Parts Modified and Reidentified is installed on the
airplane, make sure that the existing part is not used on any other airplane until the part is modified and
reidentified in accordance with Work Package 3 of this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
56 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 57

Group 6:
TABLE 5: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin. (d)
OPTION 1: Do a review
of maintenance records
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
All airplanes
OPTION 2: Inspect the
MLG forward and aft
trunnion pin assemblies
to find if any of the exist-
ing part numbers in Para-
graph 2.C.3., Parts Modi-
fied and Reidentified are
installed on the airplane.
---No further action is re-
quired.
No existing part numbers
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
30 days. See foot-
note (a)
-Within 30 days
after the Revi-
sion 2 date of
this service bul-
letin.
Lubricate the applicable
MLG forward and aft
trunnion pin assemblies
in accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 1.
Any existing part number
in Paragraph 2.C.3., Parts
Modified and Reidentified
installed on the Airplane.
18 months. See
footnote (a)
-Within 6 months
after the Revi-
sion 2 date of
this service bul-
letin.
Do a general visual in-
spection of the applicable
MLG forward and aft
trunnion pin assemblies
with the MLG not re-
moved for signs of corro-
sion and chrome plating
damage in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
57 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 58

Group 6:
TABLE 5: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
Lubricate the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
No sign of corrosion or
chrome plating damage
found during general visual
inspection of the MLG for-
ward and aft trunnion pin
assemblies in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG
forward trunnion pin as-
sembly in accordance
with Paragraph 3.B.,
Work Instructions, Work
Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG forward
trunnion pin assembly dur-
ing general visual inspec-
tion in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
No overhaul or replace-
ment of the MLG forward
trunnion pin assembly is
necessary. Lubricate the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Overhaul or replace the
applicable MLG forward
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
See footnote (b)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG forward trunnion pin
assembly in accordance
with Paragraph 3.B., Work
Instructions, Work Package
2.
--Before further
flight.
Do a detailed inspection
of the applicable MLG aft
trunnion pin assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 2.
Any sign of corrosion or
chrome plating damage
found on a MLG aft trun-
nion pin assemblies during
general visual inspection in
accordance with Paragraph
3.B., Work Instructions
Work Package 2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
58 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 59

Group 6:
TABLE 5: MAIN LANDING GEAR (MLG) TRUNNION PIN ASSEMBLIES CORROSION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
--Before further
flight.
No overhaul or replace-
ment of the MLG aft trun-
nion pin assembly is nec-
essary. Lubricate the ap-
plicable MLG aft trunnion
pin assembly in accor-
dance with Paragraph
3.B., Work Instructions,
Work Package 2.
No areas of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Before further
flight.
Overhaul or replace the
applicable MLG aft trun-
nion pin assembly in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 2. See
footnote (c)
Any area of loose or miss-
ing chrome plating or corro-
sion found during detailed
inspection of applicable
MLG aft trunnion pin as-
sembly in accordance with
Paragraph 3.B., Work In-
structions, Work Package
2.
--Within 10 years
after the Revi-
sion 2 date of
this service bul-
letin.
Do the MLG trunnion pin
assembly changes in ac-
cordance with Paragraph
3.B., Work Instructions,
Work Package 3. See
footnote (a)
All airplanes
(a) Installation of the new and improved parts in accordance with Work Package 3 is the terminating action
for the repeat lubrication and repeat inspection tasks given in this service bulletin.
(b) Forward trunnion pins can be overhauled at the operators approved maintenance facility in accordance
with CMM 57-15-01 "Repair 12-3 and Repair 12-4" revision 30, dated July 01, 2014 or later Boeing ap-
proved revisions that are published on myboeingfleet.
(c) Aft trunnion pins can be overhauled at the operators approved maintenance facility in accordance with
CMM 32-11-09 "Repair 3-1" revision 23, dated March 01, 2014 or later Boeing approved revisions that
are published on myboeingfleet.
(d) If any existing part number from Paragraph 2.C.3., Parts Modified and Reidentified is installed on the
airplane, make sure that the existing part is not used on any other airplane until the part is modified and
reidentified in accordance with Work Package 3 of this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
59 of 226
BOEING SERVICE BULLETIN 737-32-1448

### Page 60

Group 4-5, Configuration 2:
TABLE 6: MAIN LANDING GEAR (MLG) TRUNNION PIN HOUSING ASSEMBLY SEAL AND RETAIN-
ER CHANGE
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 10 years af-
ter the Revision 2
date of this service
bulletin.
Replace the MLG forward
trunnion pin housing as-
sembly seal, support ring
assembly, and retainer in
accordance with Para-
graph 3.B., Work Instruc-
tions, Work Package 4.
Airplanes with Main Land-
ing Gear that was changed
in accordance with Work
Package 3 of the original
issue of this service bul-
letin.
F. Approval
NOTE: The approval statement that follows is valid for all affected airplanes, except 737-700C
airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
This service bulletin is also approved for airplanes having FAA Aviation Partners Boeing (APB)
Supplemental Type Certificate (STC) number ST00830SE installed (not including any areas affected
by the split scimitar winglet configuration).
For BBJ models that have APB winglets installed by STC number ST00830SE, the operator is
responsible for obtaining appropriate regulatory agency approval before incorporating this service
bulletin if the bulletin is in the area affected by blended winglets.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
The Manager of the FAA Seattle Aircraft Certification Office approves accomplishment of the inspection
program, lubrication, corrective actions, and modifications, with the corresponding compliance times,
defined in Paragraph 1.E., Compliance, Tables 1, 2, and 3 of this service bulletin as an alternative
method of compliance to the corresponding requirements of paragraphs (g), (h), (i), and (j) of AD
2016-18-01.
NOTE: The approval statement that follows is valid for 737-700C airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved for all airplanes
listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other approved Boeing changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 19, 2011
737-32-1448Revision 2: August 02, 2017
60 of 226
BOEING SERVICE BULLETIN 737-32-1448

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-32-1448/file/bab571c8cf4d.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
