# Boeing Special Attention Service Bulletin 737-52-1170: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0393; AD 2018-26-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 737-52-1170](https://openairdocs.org/service-documents/boeing/sb-737-52-1170.md)
- Title as filed: SB-737-52-1170-01--BOEING
- Pages: 148
- PDF: https://openairdocs.org/files/sha256/7b/c7/7bc73a8bce4f6d11fb2640129f646a7f226deb3890fe1ad04409a13dd93cd533
- Page: https://openairdocs.org/service-documents/boeing/sb-737-52-1170/file/7bc73a8bce4f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-52-1170
Original Issue: July 29, 2014
Revision 1: December 19, 2017
ATA System: 5280
SUBJECT: DOORS - Landing Gear Center Door Assembly Attachments - Inspection, Repair and
Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2014 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
1 of 148
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
2 of 148
BOEING SERVICE BULLETIN 737-52-1170
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
S u m m a r y  ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A . E f f e c t i v i t y  ............................................... 1 1
1. Airplanes ............................................ 1 1
2 . S p a r e s  A f f e c t e d  ........................................ 3 4
B. Concurrent Requirements ...................................... 3 4
C. Reason ................................................ 3 4
D. Description .............................................. 3 5
E. Compliance .............................................. 3 7
F . A p p r o v a l  ............................................... 4 7
G. Manpower .............................................. 4 7
H. Weight and Balance Changes .................................... 5 0
I. Electrical Load Data ......................................... 5 0
J . R e f e r e n c e s  .............................................. 5 0
1. Existing Data: ......................................... 5 0
2. Data Supplied with this Service Bulletin: ........................... 5 1
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 5 1
K. Publications Affected ........................................ 5 1
L. Interchangeability and Intermixability of Parts ........................... 5 1
M. Software Accomplishment Summary ................................ 5 1
2. MATERIAL INFORMATION ........................................ 5 3
A. Material - Price and Availability ................................... 5 3
B. Industry Support Information .................................... 5 4
C. Parts Necessary for Each Airplane ................................. 5 4
1 . K i t s / P a r t s  ............................................ 5 4
2. Parts and Materials Supplied by the Operator ........................ 5 5
3. Parts Modified and Reidentified ................................ 5 5
4. Parts Removed and Not Replaced .............................. 5 5
D. Parts Necessary to Change Spares ................................. 5 6
E. Special Tooling - Price and Availability ............................... 5 6
F. Special Tooling Necessary to do this Service Bulletin ....................... 5 6
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 5 7
A. GENERAL INFORMATION ..................................... 5 7
B. WORK INSTRUCTIONS ....................................... 5 9
FIGURE 1: LEFT MLG CENTER DOOR ASSEMBLY - RETENTION CLIP ASSEMBLIES AND ATTACHMENT
BOLT - DETAILED INSPECTION [Group 1; Group 2, Configuration 1; Group 3] ...... 7 2
FIGURE 2: RIGHT MLG CENTER DOOR ASSEMBLY - RETENTION CLIP ASSEMBLIES AND
ATTACHMENT BOLT - DETAILED INSPECTION [Group 1; Group 2, Configuration 1; Group 3]
.................................................. 7 5
FIGURE 3: LEFT MLG CENTER DOOR ASSEMBLY - ATTACHMENT BOLT - DETAILED INSPECTION
[Group 2, Configuration 2] ................................... 7 8
FIGURE 4: RIGHT MLG CENTER DOOR ASSEMBLY - ATTACHMENT BOLT - DETAILED INSPECTION
[Group 2, Configuration 2] ................................... 8 1
FIGURE 5: LEFT MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENT [Group 1; Group 2,
Configuration 1; Group 3] ................................... 8 4
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
3 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 4

FIGURE 6: LEFT MLG CENTER DOOR ASSEMBLY - RETENTION CLIP REMOVAL [Group 1; Group 2,
Configuration 1; Group 3] ................................... 9 0
FIGURE 7: RIGHT MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENT [Group 1; Group
2, Configuration 1; Group 3] .................................. 9 4
FIGURE 8: RIGHT MLG CENTER DOOR ASSEMBLY - RETENTION CLIP REMOVAL [Group 1; Group 2,
Configuration 1; Group 3] ................................... 1 0 0
FIGURE 9: LEFT MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENT [Group 2, Configuration
2; Group 3] .......................................... 1 0 4
FIGURE 10: LEFT MLG CENTER DOOR ASSEMBLY ATTACHMENT ASSEMBLIES - REMOVAL [Group
2, Configuration 2; Group 3] ................................. 1 0 8
FIGURE 11: RIGHT MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENT [Group 2,
Configuration 2; Group 3] ................................... 1 1 1
FIGURE 12: RIGHT MLG CENTER DOOR ASSEMBLY ATTACHMENT ASSEMBLIES - REMOVAL [Group
2, Configuration 2; Group 3] ................................. 1 1 5
FIGURE 13: LEFT MLG CENTER DOOR ASSEMBLY - MODIFICATION ................ 1 1 8
FIGURE 14: RIGHT MLG CENTER DOOR ASSEMBLY - MODIFICATION ............... 1 2 3
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E., COMPLIANCE: TABLE 1 AND TABLE 3 [Group 1;
Group 2, Configuration 1] ................................... 1 2 8
APPENDIX B: LOGIC DIAGRAM FOR PARAGRAPH 1.E., COMPLIANCE: TABLE 2 AND TABLE 3 [Group 2,
Configuration 2] ........................................ 1 3 2
APPENDIX C: LOGIC DIAGRAM FOR PARAGRAPH 1.E., COMPLIANCE: TABLE 4, TABLE 5, TABLE 6, AND
TABLE 3 [Group 3] ...................................... 1 3 6
APPENDIX D: MLG CENTER DOOR LOWER ATTACHMENT INSTALLATION CONFIGURATIONS  [Group
3 ]  ................................................ 1 4 3
APPENDIX E: PART DEMAND INTENT ................................... 1 4 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
4 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 5

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-52-1170Original Issue: July 29, 2014
Revision 1: December 19, 2017
ATA System: 5280
SUBJECT: DOORS - Landing Gear Center Door Assembly Attachments - Inspection, Repair and
Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Effects of this Revision on airplanes Line Numbers 1 - 4274 on which the Original Issue was previously done.
None.
Airplane Line Numbers 4275-6724, and 6736 were added to Group 3 of this service bulletin effectivity.
REASON FOR REVISION
This revision is sent to clarify the MLG center door assembly retention clip assembly adjustment washer quantity,
type and location.
This revision also adds Group 3 airplanes to the service bulletin effectivity. These airplanes had been delivered
with the terminating action (fully captured bolt retention clip assembly) MLG center door lower attachment
configuration. The maintenance procedures provided instructions that could have put Group 3 airplanes in a
configuration other than the delivered terminating action configuration. Group 3 airplanes does a one-time
inspection to determine the MLG center door lower attachment configuration and does related investigative and
corrective action.
These sections were changed:
1. In Summary, updated Action, Industry Support Information, Manpower, Material Information and
Summary art.
2. In Paragraph 1.A.1., Airplanes, added Group 3 and Appendix D reference.
3. In Paragraph 1.D., Description, added Group 3 summarization of work to be done. Reformatted existing
summarization of work to be done.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
5 of 148

### Page 6

4. In Paragraph 1.E., Compliance, added Group 3 compliance information. Reformatted existing compliance
information.
5. In Paragraph 1.F., Approval, changed approval statement.
6. In Paragraph 1.G., Manpower, added Group 3 manpower data.
7. In Paragraph 2.A., Material - Price and Availability and Paragraph 2.C., Parts Necessary for Each
Airplane, changed kitting information and changed information in the Parts and Materials Supplied by
the Operator table.
8. In Paragraph 2.B., Industry Support Information, updated warranty statement.
9. In Paragraph 3.A.,General Information, updated general notes..
10. In Paragraph 3.B., Work Instructions, added Group 3 work instructions. Reformatted existing work
instructions.
11. In Figures 1 through 14, updated illustrations.
12. In Figures 1, 2, 5, 6, 7, 8, 9, 11, 13, and 14, changed step table.
13. In Appendix A, added tables for description of parts, conditions, and flag notes and changed logic
diagram.
14. In Appendix B through Appendix F, added new appendicies.
The data given in Information Notice 737-52-1170 IN 01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
July 29, 2014Original Issue:
December 19, 2017Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
6 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 7

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-52-1170Original Issue: July 29, 2014
Revision 1: December 19, 2017
ATA System: 5280
SUBJECT: DOORS - Landing Gear Center Door Assembly Attachments - Inspection, Repair and
Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions to inspect for loose, missing, damaged or bottomed out attachment bolts
or any damage to the retention clip assemblies of the Main Landing Gear (MLG) center door assemblies. In
flight vibrations can cause the movement of the attachment bolts during flight which could also result in damage
to the MLG shock strut bushings. If the attachment bolts loosen and depart the airplane, this could result in
departure of the center and inboard door assemblies that could impact and cause significant damage to the
main flap and horizontal stabilizer. A modification and repair is provided to replace the retention clip assemblies.
Failure to accomplish this service bulletin could result in departure of the center and inboard door assemblies,
subsequent damage to the main flap and horizontal stabilizer, and loss of control of the airplane.
One operator reported the departure and loss of the center and inboard door assemblies from the left MLG
during flight. The airplane had completed 28,279 flight cycles when the incident occurred. There have also been
several reports of the two inboard bolts that attach the MLG center door assembly to the shock strut cylinder
being loose or missing. One operator reported loose, worn and missing attachment bolts on several airplanes
with the reported airplane flight cycles ranging from 15,921 to 31,673.
A new design of retention clip assemblies is installed in production after line number 4274.
Boeing Service Related Problem (SRP) 737NG-SRP-52-0101 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 737NG FTD 52-12001 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
7 of 148

### Page 8

ReferenceAffectedPlanning Data
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Refer to Paragraph 1.D., Description.
EFFECTIVITY
737-600/-700/-700C/-800/-900/-900ER airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected
airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for 737 airplanes in warranty as of January 26, 2012. Please refer to
Paragraph 2.B., Industry Support Information. The warranty remedies will expire eight years from the original
issue date of this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
8 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 9

Operators are encouraged to complete the survey provided in APPENDIX E of this service bulletin to help Boeing
predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
9 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 10 (OCR)

BOEING SERVICE BULLETIN 737-52-1170
FWD
MLG CENTER  DOOR ASSEMBLY  STRUT  MLG SHOCK
MLG INBOARD
DOOR ASSEMBLY
Original Issue: July 29, 2014
Revision 1: December 19, 2017
- GROUP 1, GROUP 2 CONFIGURATIONS
1 AND 2:
DO A DETAILED INSPECTION FOF
LOOSE, MISSING OR DAMAGED PARTS.
IF ANY PARTS ARE LOOSE, MISSING
OR DAMAGED, REMOVE THE MLG
CENTER DOOR AND DO ALL RELATED
INVESTIGATIVE AND CORRECTIVE
ACTIONS. REPEAT INSPECT UNTIL
INSTALLATION OF MLG CENTER DOOR
LOWER ATTACHMENT FULLY
CAPTURED BOLT RETENTION
MODIFICATION IS DONE.
GROUP 3:
DO A ONE-TIME CHECK OF
MAINTENANCE RECORDS OR AN
ON-AIRPLANE CHECK TO DETERMINE
MLG CENTER DOOR ATTACHMENT
INSTALLATION CONFIGURATION AND  DO ALL RELATED INVESTIGATIVE AND  2264815
CORRECTIVE ACTIONS.
PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-52-1170
Work - See page 1 for detalls.  10 of 148

### Page 11

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-52-1170
Original Issue: July 29, 2014
Revision 1: December 19, 2017
ATA System: 5280
SUBJECT: DOORS - Landing Gear Center Door Assembly Attachments - Inspection, Repair and
Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D6-19567 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is for the airplane(s) shown below.
Refer to APPENDIX D for identification of MLG center door lower attachment installation
configurations.
DESCRIPTIONCONFIGURATIONGROUP
737-600/-700/-700C/-800/-900/-900ER airplanes line numbers 1-4274
less airplane line numbers 4, 6, 9-20, 22-29, 31-100, 102-106.
Airplanes that have accomplished service bulletin 737-52-1133. MLG
center door lower attachments with partially captured bolt retention
assemblies installed
-1
737-600/-700/-800 airplane line numbers 4, 6, 9-20, 22-29, 31-100,
102-106.
-2
Airplanes that have accomplished service bulletin 737-52-1133. MLG
center door lower attachments with partially captured bolt retention
assemblies installed.
1
Airplanes that have not accomplished service bulletin 737-52-1133.
MLG center door lower attachments with no bolt retention assemblies
installed.
2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
11 of 148

### Page 12

DESCRIPTIONCONFIGURATIONGROUP
737-700/-800/-900ER airplane line numbers 4275-6724, and 6736.
MLG center door lower attachments delivered with fully captured bolt
retention assemblies installed.
-3
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
GroupVariable Number
1YA001 - YA003
2YA004 - YA019
1YA020 - YA099
1YA101 - YA199
2YA201 - YA203
1YA204 - YA211
1YA221
1YA231
2YA232 - YA242
2YA251 - YA252
1YA253 - YA256
2YA271 - YA272
2YA291
2YA301 - YA302
2YA311 - YA312
1YA313 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
2YA501 - YA512
1YA513 - YA536
2YA541
1YA542 - YA552
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
12 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 13

GroupVariable Number
2YA571 - YA572
1YA573 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
2YA701 - YA703
1YA704 - YA710
1YA721 - YA722
1YA731 - YA734
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
13 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 14

GroupVariable Number
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB635
3YB636
1YB651
1YB656
1YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB893
1YB901 - YB903
1YB911
1YB961 - YB975
1YB981
1YB986 - YB998
1YC001 - YC002
2YC003 - YC007
1YC008 - YC030
2YC051 - YC053
1YC054 - YC070
2YC071 - YC073
1YC074 - YC084
1YC091 - YC095
2YC101 - YC102
1YC103 - YC104
2YC111
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
14 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 15

GroupVariable Number
1YC112 - YC113
2YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC179
1YC186 - YC190
1YC201 - YC203
1YC206 - YC207
2YC301 - YC302
1YC303 - YC305
2YC321 - YC330
1YC331 - YC380
2YC381
1YC382 - YC387
1YC391 - YC394
1YC396
2YC401 - YC404
1YC405 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC439
1YC441 - YC448
1YC451 - YC455
1YC459
1YC461 - YC467
1YC471 - YC499
2YC501 - YC505
1YC506 - YC526
1YC571 - YC583
1YC587 - YC589
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
15 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 16

GroupVariable Number
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
1YC701 - YC715
1YC720 - YC725
1YC727 - YC752
1YC761 - YC770
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
1YD256 - YD257
1YD261
1YD301 - YD334
1YD391
1YD401 - YD410
1YD412 - YD419
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
16 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 17

GroupVariable Number
3YD420 - YD422
1YD481 - YD485
1YD491 - YD499
1YD501 - YD512
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
1YD591 - YD595
1YD601 - YD612
1YD651 - YD655
1YE001 - YE002
2YE003 - YE005
1YE006 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
1YF001 - YF011
1YF021 - YF049
1YF051 - YF069
3YF070 - YF080
1YF086 - YF087
1YF106 - YF107
1YF111 - YF114
1YF116 - YF119
1YF121 - YF132
1YF176 - YF178
1YF191 - YF192
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
17 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 18

GroupVariable Number
1YF201 - YF276
1YF401 - YF402
1YF431 - YF432
1YF436 - YF437
1YF441 - YF442
1YF451 - YF460
1YF501 - YF599
1YF601 - YF661
3YF662 - YF685
3YF691 - YF695
1YF701 - YF707
1YF801 - YF805
1YF831 - YF832
1YF836 - YF838
1YF871
3YF872
1YF901 - YF905
1YF921 - YF928
1YF951 - YF954
1YG001 - YG044
1YG061 - YG064
1YG066 - YG089
1YG091 - YG099
1YG101 - YG104
1YG111 - YG114
1YG116 - YG136
3YG137 - YG138
1YG201 - YG205
1YG211 - YG214
1YG221 - YG224
1YG251 - YG252
1YG501 - YG512
1YG601 - YG602
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
18 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 19

GroupVariable Number
1YG701
1YG711
1YH001 - YH012
1YH031 - YH055
1YH071 - YH080
1YH101 - YH132
1YH201 - YH202
1YH206 - YH207
1YH301 - YH306
3YH307
1YH321 - YH322
1YH501 - YH524
3YH525 - YH542
1YH551 - YH569
3YH570 - YH594
1YH601 - YH604
3YH605 - YH606
1YH611 - YH619
3YH620
1YH631 - YH632
3YH636 - YH637
1YH641
3YH681 - YH685
1YH701 - YH702
3YH703 - YH755
3YH801 - YH888
3YH901 - YH908
3YH911 - YH915
3YH951 - YH952
1YJ001 - YJ013
1YJ021
1YJ471 - YJ480
1YJ501 - YJ517
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
19 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 20

GroupVariable Number
1YJ531 - YJ579
1YJ591 - YJ599
1YJ631 - YJ632
1YJ671 - YJ694
1YJ801 - YJ867
1YJ871 - YJ880
1YJ901 - YJ904
1YJ908 - YJ929
1YJ931 - YJ937
1YJ941 - YJ956
1YJ961
1YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
1YK131 - YK133
1YK136 - YK139
1YK141 - YK142
1YK146 - YK148
1YK151 - YK154
1YK161 - YK167
1YK171
1YK176 - YK177
1YK186
1YK191
1YK196
1YK201 - YK202
1YK301 - YK314
1YK321 - YK340
1YK361 - YK378
1YK401 - YK406
1YK426 - YK427
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
20 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 21

GroupVariable Number
1YK431 - YK450
1YK456 - YK467
1YK471 - YK473
1YK476
3YK478
1YK480 - YK487
1YK491 - YK493
1YK495 - YK499
1YK511 - YK516
1YK521 - YK530
1YK551 - YK571
1YK576 - YK577
1YK580 - YK585
1YK601 - YK602
1YK606 - YK607
1YK611 - YK616
1YK621 - YK634
1YK641 - YK644
1YK651 - YK665
1YK671 - YK672
1YK676 - YK677
1YK681 - YK686
1YK691
1YK695
3YK696 - YK699
1YK701 - YK713
1YK716 - YK719
1YK721 - YK741
1YK751 - YK770
1YK776 - YK778
1YK781 - YK785
1YK791 - YK792
1YK796 - YK797
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
21 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 22

GroupVariable Number
1YK801 - YK899
1YK901 - YK912
1YK918 - YK919
1YK921 - YK929
1YK941 - YK999
1YL001 - YL005
1YL011 - YL016
1YL021 - YL024
1YL051 - YL052
1YL056 - YL057
1YL061
1YL066 - YL069
1YL076 - YL077
1YL101 - YL137
1YL201 - YL237
1YL241 - YL242
1YL271 - YL272
1YL281 - YL284
1YL301 - YL303
1YL311 - YL314
1YL316 - YL321
1YL351 - YL353
1YL371 - YL374
1YL401
1YL421 - YL429
1YL431 - YL444
1YL461 - YL478
1YL501 - YL509
1YL531 - YL534
1YL541 - YL551
1YL561 - YL579
1YL591 - YL598
1YL601 - YL606
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
22 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 23

GroupVariable Number
1YL611 - YL612
1YL616 - YL617
1YL621
1YL626
1YL631 - YL634
1YL636 - YL637
1YL661 - YL664
1YL676 - YL691
1YL696 - YL697
1YL701 - YL707
1YL731
1YL751 - YL752
1YL756 - YL757
1YL761 - YL780
1YL796 - YL797
1YL801 - YL815
1YL901 - YL910
1YL921 - YL940
1YL951 - YL968
1YM101 - YM103
1YM201 - YM244
1YM251 - YM299
1YM301 - YM399
1YM401 - YM415
1YM471
1YM481 - YM484
1YM501 - YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
1YM581 - YM582
1YM591 - YM599
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
23 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 24

GroupVariable Number
1YM631 - YM634
1YM641 - YM652
1YM671 - YM674
1YM691 - YM699
1YM701 - YM710
1YM761 - YM765
1YM771 - YM779
1YN001 - YN016
1YN021 - YN024
1YN061
1YN071 - YN082
1YN091 - YN092
1YN101 - YN112
1YN121
1YN126
1YN201 - YN202
1YN211 - YN219
1YN231 - YN236
1YN261
1YN501
1YN531 - YN534
1YN551 - YN554
3YN555
1YN601 - YN606
3YN651 - YN652
3YN666 - YN667
3YN671 - YN672
1YN701 - YN702
3YN741 - YN742
1YQ001 - YQ003
1YQ011 - YQ021
1YQ026 - YQ029
1YQ036 - YQ045
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
24 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 25

GroupVariable Number
1YQ201 - YQ202
3YQ203 - YQ207
1YQ231
1YQ241 - YQ251
1YQ281 - YQ284
1YQ291 - YQ296
1YQ301 - YQ302
1YQ321 - YQ323
3YQ324
3YQ331 - YQ334
3YQ346 - YQ347
3YQ351 - YQ367
3YQ371
1YQ401 - YQ403
1YQ451 - YQ454
1YQ456
1YQ461
1YQ471
1YQ501 - YQ502
3YQ503 - YQ520
3YQ601 - YQ602
3YQ606
3YQ610 - YQ612
1YR001 - YR020
3YR021 - YR050
1YR051 - YR062
3YR063 - YR090
1YR091 - YR096
3YR097 - YR098
1YR101 - YR102
3YR103 - YR105
1YR111 - YR117
3YR118 - YR124
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
25 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 26

GroupVariable Number
1YR126 - YR143
3YR144
1YR166 - YR182
3YR186 - YR198
1YR201 - YR204
3YR205 - YR215
1YR231 - YR258
3YR259 - YR270
1YR271 - YR288
3YR289 - YR290
1YR291 - YR294
1YR296 - YR297
1YR301 - YR321
3YR322 - YR334
3YR338 - YR341
1YR361 - YR366
3YR371 - YR373
3YR376 - YR377
1YR381 - YR382
1YR386
3YR387 - YR388
3YR391
3YR396 - YR399
1YR401 - YR405
1YR411 - YR412
3YR413
1YR416 - YR417
3YR418
1YR421 - YR422
3YR423 - YR424
3YR426 - YR430
1YR431 - YR435
3YR436 - YR440
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
26 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 27

GroupVariable Number
1YR441 - YR445
3YR446 - YR450
1YR451 - YR455
1YR457 - YR467
3YR468 - YR499
1YR501 - YR506
1YR511 - YR514
3YR515
1YR516 - YR520
1YR526 - YR532
3YR533 - YR535
1YR536 - YR540
3YR541 - YR544
3YR546 - YR551
3YR556 - YR562
3YR571 - YR582
3YR591 - YR592
1YR601 - YR605
1YR616 - YR621
3YR622 - YR650
1YR651 - YR658
1YR661 - YR663
3YR671 - YR673
3YR676 - YR678
3YR681 - YR682
1YR701 - YR742
3YR743 - YR769
3YR771 - YR799
1YR801 - YR812
3YR813 - YR826
1YR831 - YR838
1YR841 - YR845
3YR846 - YR850
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
27 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 28

GroupVariable Number
1YR851 - YR863
3YR864 - YR899
1YR901 - YR903
1YR931 - YR932
3YR933 - YR934
3YR938 - YR940
1YR941 - YR942
3YR943 - YR944
1YR951 - YR954
3YR955 - YR980
1YR981 - YR989
3YR990 - YR998
1YS001 - YS002
3YS006 - YS009
1YS031 - YS032
1YS051 - YS060
3YS061 - YS073
1YS101 - YS108
3YS109 - YS120
3YS126 - YS142
3YS146 - YS150
1YS151 - YS160
1YS166 - YS167
3YS168 - YS194
3YS196 - YS197
1YS201
3YS202 - YS209
1YS221 - YS223
3YS224 - YS225
3YS231 - YS236
1YS271 - YS273
3YS274 - YS288
3YS295 - YS296
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
28 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 29

GroupVariable Number
1YS301 - YS312
3YS313 - YS348
3YS351 - YS370
1YS371 - YS373
3YS374 - YS378
3YS381 - YS383
3YS401
3YS451
3YS456 - YS457
3YS462 - YS465
3YS467
1YS501 - YS502
3YS506
3YS511 - YS518
3YS531
3YS536 - YS538
3YS541 - YS542
3YS546
1YS551 - YS553
3YS554 - YS556
1YS561
3YS562 - YS578
3YS581 - YS590
1YS591
3YS592 - YS595
1YS601 - YS626
3YS627 - YS685
1YS686 - YS690
1YS701 - YS703
3YS704 - YS713
1YS721 - YS726
3YS727 - YS762
1YS771 - YS772
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
29 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 30

GroupVariable Number
3YS773 - YS780
3YS806 - YS810
3YS816 - YS818
3YS823 - YS825
3YS851 - YS863
3YS876
3YS881 - YS883
3YS891
3YS896 - YS897
3YS901 - YS909
3YS911 - YS957
3YS961 - YS974
3YS976 - YS977
3YS981 - YS987
3YS991 - YS998
3YT001 - YT004
3YT006
3YT026 - YT027
3YT031 - YT032
3YT036 - YT038
3YT061 - YT068
3YT101 - YT138
3YT176 - YT185
3YT191
3YT196 - YT199
3YT201
3YT206 - YT207
3YT211 - YT213
3YT251 - YT299
3YT301 - YT307
3YT311 - YT312
3YT321 - YT355
3YT371 - YT372
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
30 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 31

GroupVariable Number
3YT381
3YT391 - YT396
3YT401 - YT403
3YT411 - YT417
3YT427
3YT461 - YT477
3YT491 - YT492
3YT501 - YT521
3YT551 - YT552
3YT556 - YT563
3YT565
3YT571 - YT576
3YT601 - YT606
3YT701 - YT708
3YT761 - YT781
3YT791 - YT794
3YT796 - YT797
3YT801 - YT804
3YT811 - YT813
3YT826 - YT827
3YT831 - YT832
3YT841 - YT849
3YT851 - YT852
3YT856 - YT863
3YT885 - YT887
3YT891 - YT895
3YT901 - YT990
3YU001 - YU060
3YU201 - YU216
3YU301 - YU316
3YV001 - YV004
3YV006 - YV012
3YV021 - YV023
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
31 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 32

GroupVariable Number
3YV030 - YV034
3YV037 - YV042
3YV045 - YV047
3YV051 - YV057
3YV081
3YV083 - YV084
3YV097 - YV099
3YV101 - YV154
3YV201
3YV251 - YV252
3YV256 - YV257
3YV301 - YV312
3YV351 - YV368
3YV381 - YV388
3YV391 - YV394
3YV401
3YV411
3YV431 - YV433
3YV441 - YV452
3YV461 - YV462
3YV467 - YV468
3YV501 - YV505
3YV521
3YV571 - YV583
3YV601 - YV605
3YV651 - YV664
3YV695 - YV696
3YV711
3YV722 - YV731
3YV741 - YV771
3YV781 - YV788
3YV801 - YV815
3YV831
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
32 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 33

GroupVariable Number
3YV881 - YV883
3YV901 - YV915
3YV923 - YV926
3YV971 - YV980
3YW001
3YW011 - YW099
3YW101 - YW114
3YW201
3YW226 - YW240
3YW245 - YW252
3YW261
3YW263
3YW267 - YW281
3YW283 - YW285
3YW292 - YW296
3YW351
3YW356 - YW358
3YW361 - YW363
3YW371 - YW391
3YW401 - YW413
3YW441
3YW451 - YW452
3YW471 - YW472
3YW491 - YW492
3YW531
3YW551 - YW559
3YW585 - YW590
3YW595 - YW596
3YW616 - YW619
3YW666
3YW881
3YW891 - YW893
3YW906 - YW907
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
33 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 34

GroupVariable Number
3YW916 - YW918
3YW971 - YW976
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
This service bulletin gives instructions to inspect for loose, missing, damaged or bottomed out attachment
bolts or any damage to the retention clip assemblies of the Main Landing Gear (MLG) center door
assemblies. In flight vibrations can cause the movement of the attachment bolts during flight which
could also result in damage to the MLG shock strut bushings. If the attachment bolts loosen and depart
the airplane, this could result in departure of the center and inboard door assemblies that could impact
and cause significant damage to the main flap and horizontal stabilizer. A modification and repair is
provided to replace the retention clip assemblies. Failure to accomplish this service bulletin could result
in departure of the center and inboard door assemblies, subsequent damage to the main flap and
horizontal stabilizer, and loss of control of the airplane.
One operator reported the departure and loss of the center and inboard door assemblies from the left
MLG during flight. The airplane had completed 28,279 flight cycles when the incident occurred. There
have also been several reports of the two inboard bolts that attach the MLG center door assembly to
the shock strut cylinder being loose or missing. One operator reported loose, worn and missing
attachment bolts with the reported airplane flight cycles ranging from 15,921 to 31,673.
A new design of retention clip assemblies is installed in production after line number 4274.
Boeing Service Related Problem (SRP) 737NG-SRP-52-0101 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 737NG FTD 52-12001 is related to this service bulletin.
The data given in Information Notice 737-52-1170 IN 01 is included in this revision.
This revision is sent to clarify the MLG center door assembly retention clip assembly adjustment washer
quantity, type and location.
This revision also adds Group 3 airplanes to the service bulletin effectivity. These airplanes had been
delivered with the terminating action (fully captured bolt retention clip assembly) MLG center door lower
attachment configuration. The maintenance procedures provided instructions that could have put Group
3 airplanes in a configuration other than the delivered terminating action configuration. Group 3 airplanes
does a one-time inspection to determine the MLG center door lower attachment configuration and does
related investigative and corrective action.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
34 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 35

D. Description
Group 1; Group 2, Configuration 1:
1. Get access to the Main Landing Gear (MLG) center door assembly. Do a detailed inspection of
the forward and aft center door assembly attachments for loose, missing, damaged, or bottomed
out attachment bolts, and any wear to the retention clip assemblies. If any bolts are loose, missing,
damaged, or bottomed out or there is any wear to the retention clip assemblies, remove the center
door assembly attachments and do a detailed inspection/measurement of the MLG shock strut
bushings for excessive wear, galling, and any crack. If no bolts are loose, missing, damaged, or
bottomed out and there is no wear to the retention clip assemblies, repeat inspections or install
the fully captured bolt retention clip assembly modification.
2. If any excessive wear, galling, or crack is found, do a bushing replacement and lug magnetic
particle inspection or fluorescent penetrant inspection for any crack and corrosion of the bushing
hole in the shock strut attachment lug and repair if any crack or corrosion is found. Then replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification. If no excessive wear, galling, or crack is found, replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification.
Group 2, Configuration 2:
1. Get access to the Main Landing Gear (MLG) center door assembly. Do a detailed inspection of
the forward and aft center door assembly attachments for loose, missing, or damaged attachment
bolts. If any bolts are loose, missing, or damaged, remove the center door assembly attachments
and do a detailed inspection/measurement of the MLG shock strut bushings for excessive wear,
galling, and any crack. If no bolts are loose, missing, or damaged, repeat inspections or install the
fully captured bolt retention clip assembly modification.
2. If any excessive wear, galling, or crack is found, do a bushing replacement and lug magnetic
particle inspection or fluorescent penetrant inspection for any crack and corrosion of the bushing
hole in the shock strut attachment lug and repair if any crack or corrosion is found. Then replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification. If no excessive wear, galling, or crack is found, replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification.
Group 3:
1. Do a maintenance records check or an on-airplane check to determine Main Landing Gear (MLG)
center door lower attachment installation configuration.
2. If no retention clip assemblies are installed, do a detailed inspection of the forward and aft center
door assembly attachments for loose, missing, or damaged attachment bolts. If any bolts are loose,
missing, or damaged, remove the center door assembly attachments and do a detailed
inspection/measurement of the MLG shock strut bushings for excessive wear, galling, and any
crack. If no bolts are loose, missing, or damaged, repeat inspections or install the fully captured
bolt retention clip assembly modification.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
35 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 36

If any excessive wear, galling, or crack is found, do a bushing replacement and lug magnetic
particle inspection or fluorescent penetrant inspection for any crack and corrosion of the bushing
hole in the shock strut attachment lug and repair if any crack or corrosion is found. Then replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification. If no excessive wear, galling, or crack is found, replace
all damaged parts with new or serviceable parts and repeat inspections or install the fully captured
bolt retention clip assembly modification.
3. If partially captured bolt retention clip assemblies are installed, do a detailed inspection of the
forward and aft center door assembly attachments for loose, missing, damaged, or bottomed out
attachment bolts, and any wear to the retention clip assemblies. If any bolts are loose, missing,
damaged, or bottomed out or there is any wear to the retention clip assemblies, remove the center
door assembly attachments and do a detailed inspection/measurement of the MLG shock strut
bushings for excessive wear, galling, and any crack. If no bolts are loose, missing, damaged, or
bottomed out and there is no wear to the retention clip assemblies, repeat inspections or install
the fully captured bolt retention clip assembly modification.
If any excessive wear, galling, or crack is found, do a bushing replacement and lug magnetic
particle inspection or fluorescent penetrant inspection for any crack and corrosion of the bushing
hole in the shock strut attachment lug and repair if any crack or corrosion is found. Then replace
all damaged parts with new or serviceable parts and repeat inspection or install the fully captured
bolt retention clip assembly modification. If no excessive wear, galling, or crack is found, replace
all damaged parts with new or serviceable parts and repeat inspection or install the fully captured
bolt retention clip assembly modification.
4. If fully captured bolt retention clip assemblies are installed, no further work is required.
Effects of this Revision on airplanes Line Numbers 1 - 4274 on which the Original Issue was previously
done:
None.
Airplane Line Numbers 4275-6491, 6493-6531, 6533-6559, 6561-6593, and 6596-6606 were added
to Group 3 of this service bulletin effectivity.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
732, 733, 742, 743737-600, 737-700, 737-700C,
737-800, 737-900, 737-900ER
Group 2:
Affected Maintenance Zones
ZoneModel
732, 733, 742, 743737-600, 737-700, 737-800
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
36 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 37

Group 3:
Affected Maintenance Zones
ZoneModel
732, 733, 742, 743737-700, 737-800, 737-900ER
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
A logic diagram showing compliance tasks and compliance times is included as an aid in APPENDIX
A through APPENDIX C.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
The table that follows immediately below describes the service bulletin PARTS noted in the compliance
tables.
DescriptionTitle
MLG CENTER DOOR ASSEMBLY ATTACHMENTS - DETAILED INSPECTIONPART 2
MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENTPART 3
MLG CENTER DOOR ASSEMBLY ATTACHMENTS - REMOVALPART 4
MLG CENTER DOOR RETENTION CLIP ASSEMBLIES - MODIFICATIONPART 5
MLG CENTER DOOR ASSEMBLY BOLTS AND RETENTION CLIP ASSEMBLIES -
REPLACEMENT
PART 6
MLG LUG INSPECTION AND BUSHING REPLACEMENTPART 7
MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH NO RETENTION CLIP
ASSEMBLY - INSPECTION AND MODIFICATION
PART 9
MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH PARTIALLY CAPTURED
BOLT RETENTION CLIP ASSEMBLY - INSPECTION AND MODIFICATION
PART 10
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
37 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 38

Group 1; Group 2, Configuration 1:
Table 1: LEFT AND RIGHT MAIN LANDING GEAR (MLG) - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Oc-
curs later)
ActionCondition
-Within 800 flight
cycles after the
original issue
date of this ser-
vice bulletin.
Before 12,000 to-
tal flight cycles.
Do PART 2.All airplanes.
-Before further flight.OPTION 1 (ACTION 1):CONDITION 1: NO
LOOSE, MISSING, DAM-
AGED OR BOTTOMED
OUT ATTACHMENT
BOLTS AND NO WEAR
TO THE RETENTION
CLIP ASSEMBLIES
Do PART 4.
-Before further flight.OPTION 1 (ACTION 2):
Do PART 5. (a)
5,500 flight cy-
cles.(a)
-OPTION 2:
Repeat PART 2.
-Before further flight.Do PART 3.CONDITION 2: ANY
LOOSE, MISSING, DAM-
AGED OR BOTTOMED
OUT ATTACHMENT
BOLTS, OR ANY WEAR
TO THE RETENTION
CLIP ASSEMBLIES
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
38 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 39

Group 1; Group 2, Configuration 1:
Table 1: LEFT AND RIGHT MAIN LANDING GEAR (MLG) - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Oc-
curs later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1):CONDITION 2.1: EXCES-
SIVE WEAR FOUND IN
THE INTERNAL DIAME-
TER OF THE BUSHING
OR ANY GALLING OR
ANY CRACK FOUND
Do PART 7. (b)
-Before further flight.OPTION 1 (ACTION 2):
Do PART 5. (a)
-Before further flight.OPTION 2 (ACTION 1):
Do PART 7. (b)
-Before further flight.OPTION 2 (ACTION 2):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 2 (ACTION 3):
Repeat PART 2.
-Before further flight.OPTION 3 (ACTION 1):
Remove the center and in-
board door assemblies.
-Before installation of the center and
inboard door assemblies.
OPTION 3 (ACTION 2):
Do PART 7. (b)
-Before further flight.OPTION 3 (ACTION 3):
Do PART 5. (a)
-Before further flight.OPTION 4 (ACTION 1):
Remove the center and in-
board door assemblies.
-Before installation of the center and
inboard door assemblies.
OPTION 4 (ACTION 2):
Do PART 7. (b)
-Before further flight.OPTION 4 (ACTION 3):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 4 (ACTION 4):
Repeat PART 2.
-Before further flight.OPTION 1:CONDITION 2.2: NO EX-
CESSIVE WEAR FOUND
IN THE INTERNAL DIAM-
ETER OF THE BUSHING
AND NO GALLING AND
NO CRACK FOUND
Do PART 5. (a)
-Before further flight.OPTION 2 (ACTION 1):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 2 (ACTION 2):
Repeat PART 2.
(a) Accomplishment of PART 5: MLG CENTER DOOR RETENTION CLIP ASSEMBLIES - MODIFICATION
is terminating action to the PART 2 repeat inspection.
(b) Do Corrective actions in accordance with Table 3.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
39 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 40

Group 2, Configuration 2:
Table 2: LEFT AND RIGHT MAIN LANDING GEAR (MLG) - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Oc-
curs later)
ActionCondition
-Within 800 flight
cycles after the
original issue
date of this ser-
vice bulletin.
Before 12,000 to-
tal flight cycles.
Do PART 2.All airplanes.
-Before further flight.OPTION 1 (ACTION 1):CONDITION 3: NO
LOOSE, MISSING OR
DAMAGED ATTACH-
MENT BOLTS
Do PART 4.
-Before further flight.OPTION 1 (ACTION 2):
Do PART 5. (a)
5,500 flight cy-
cles.(a)
-OPTION 2:
Repeat PART 2.
-Before further flight.Do PART 3.CONDITION 4: ANY
LOOSE, MISSING OR
DAMAGED ATTACH-
MENT BOLTS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
40 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 41

Group 2, Configuration 2:
Table 2: LEFT AND RIGHT MAIN LANDING GEAR (MLG) - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Oc-
curs later)
ActionCondition
-Before further flight.OPTION 1 (ACTION 1):CONDITION 4.1: EXCES-
SIVE WEAR FOUND IN
THE INTERNAL DIAME-
TER OF THE BUSHING
OR ANY GALLING OR
ANY CRACK FOUND
Do PART 7. (b)
-Before further flight.OPTION 1 (ACTION 2):
Do PART 5. (a)
-Before further flight.OPTION 2 (ACTION 1):
Do PART 7. (b)
-Before further flight.OPTION 2 (ACTION 2):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 2 (ACTION 3):
Repeat PART 2.
-Before further flight.OPTION 3 (ACTION 1):
Remove the center and in-
board door assemblies.
-Before installation of the center and
inboard door assemblies.
OPTION 3 (ACTION 2):
Do PART 7. (b)
-Before further flight.OPTION 3 (ACTION 3):
Do PART 5. (a)
-Before further flight.OPTION 4 (ACTION 1):
Remove the center and in-
board door assemblies.
-Before installation of the center and
inboard door assemblies.
OPTION 4 (ACTION 2):
Do PART 7. (b)
-Before further flight.OPTION 4 (ACTION 3):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 4 (ACTION 4):
Repeat PART 2.
-Before further flight.OPTION 1:CONDITION 4.2: NO EX-
CESSIVE WEAR FOUND
IN THE INTERNAL DIAM-
ETER OF THE BUSHING
AND NO GALLING AND
NO CRACK FOUND
Do PART 5. (a)
-Before further flight.OPTION 2 (ACTION 1):
Do PART 6.
5,500 flight cy-
cles.(a)
-OPTION 2 (ACTION 2):
Repeat PART 2.
(a) Accomplishment of PART 5: MLG CENTER DOOR RETENTION CLIP ASSEMBLIES - MODIFICATION
is terminating action to the PART 2 repeat inspection.
(b) Do corrective action in accordance with Table 3.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
41 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 42

Table 3: PART 7: MLG LUG INSPECTION AND BUSHING REPLACEMENT - Corrective Actions
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
ACTION 1: Repair the
lug.
CONDITION 5: ANY
CRACK OR CORROSION
FOUND ACTION 2: Install new
bushings.
-Before further
flight.
Install new bushings.CONDITION 6: NO
CRACK AND NO CORRO-
SION FOUND
Group 3:
Table 4: LEFT AND RIGHT MAIN LANDING GEAR (MLG) CENTER DOOR LOWER ATTACHMENTS CHECK
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 800 flight
cycles after the
Revision 1 date
of this service
bulletin.
Before 12,000
total flight cy-
cles.
Do OPTION 1: MLG
CENTER DOOR LOWER
ATTACHMENT INSTAL-
LATION CONFIGURA-
TION MAINTENANCE
RECORDS CHECK.
All airplanes
Do OPTION 2: MLG
CENTER DOOR LOWER
ATTACHMENT INSTAL-
LATION CONFIGURA-
TION ON-AIRPLANE
CHECK.
--Before further
flight.
Do OPTION 2: MLG
CENTER DOOR LOWER
ATTACHMENT INSTAL-
LATION CONFIGURA-
TION ON-AIRPLANE
CHECK.
CONDITION 7: MLG CEN-
TER DOOR LOWER AT-
TACHMENT INSTALLA-
TION CONFIGURATION
COULD NOT BE DETER-
MINED AFTER ACCOM-
PLISHMENT OF OPTION
1
--Before further
flight.
Do corrective action in
accordance with Table 5.
CONDITION 8: NO RETEN-
TION CLIP ASSEMBLIES
INSTALLED
--Before further
flight.
Do corrective action in
accordance with Table 6.
CONDITION 9: PARTIAL-
LY CAPTURED BOLT RE-
TENTION CLIP ASSEM-
BLIES INSTALLED
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
42 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 43

Group 3:
Table 4: LEFT AND RIGHT MAIN LANDING GEAR (MLG) CENTER DOOR LOWER ATTACHMENTS CHECK
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
---No further work required.CONDITION 10: FULLY
CAPTURED BOLT RETEN-
TION CLIP ASSEMBLIES
INSTALLED
Group 3:
Table 5: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH NO RETENTION CLIP ASSEMBLY
- INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do PART 9.MLG center door lower at-
tachment installation config-
uration - no retention clip
assemblies installed.
-Before further
flight.
OPTION 1 (ACTION 1):
Remove the MLG center
door assembly attach-
ments.
CONDITION 11: NO
LOOSE, MISSING OR
DAMAGED ATTACHMENT
BOLTS
-Before further
flight.
OPTION 1 (ACTION 2):
Do PART 5. (a)
5,500 flight cycles.
(a)
-OPTION 2: Repeat PART
9.
-Before further
flight.
Do a detailed inspection
and measurement of the
MLG lug bushings for ex-
cessive wear, galling and
any crack.
CONDITION 12: ANY
LOOSE, MISSING OR
DAMAGED ATTACHMENT
BOLTS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
43 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 44

Group 3:
Table 5: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH NO RETENTION CLIP ASSEMBLY
- INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
OPTION 1 (ACTION 1):
Do PART 7. (b)
CONDITION 12.1: EXCES-
SIVE WEAR FOUND IN
THE INTERNAL DIAME-
TER OF THE BUSHING
OR ANY GALLING OR
ANY CRACK FOUND
-Before further
flight.
OPTION 1 (ACTION 2):
Do PART 5. (a)
-Before further flightOPTION 2 (ACTION 1):
Do PART 7. (b)
-Before further flightOPTION 2 (ACTION 2):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 2 (ACTION 3):
Repeat PART 9.
-Before further
flight.
OPTION 3 (ACTION 1):
Remove the center and
inboard door assemblies.
-Before installation
of the center and
inboard door as-
semblies.
OPTION 3 (ACTION 2):
Do PART 7. (b)
-Before further
flight.
OPTION 3 (ACTION 3):
Do PART 5. (a)
-Before further
flight.
OPTION 4 (ACTION 1):
Remove the center and
inboard door assemblies.
-Before installation
of the center and
inboard door as-
semblies.
OPTION 4 (ACTION 2):
Do PART 7. (b)
-Before further
flight.
OPTION 4 (ACTION 3):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 4 (ACTION 4):
Repeat PART 9.
-Before further
flight.
OPTION 1: Do PART 5.
(a)
CONDITION 12.2: NO EX-
CESSIVE WEAR FOUND
IN THE INTERNAL DIAME-
TER OF THE BUSHING
AND NO GALLING AND
NO CRACK FOUND
-Before further
flight.
OPTION 2 (ACTION 1):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 2 (ACTION 2):
Repeat PART 9.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
44 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 45

Group 3:
Table 5: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH NO RETENTION CLIP ASSEMBLY
- INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(a) Accomplishment of PART 5: MLG CENTER DOOR RETENTION CLIP ASSEMBLIES -
MODIFICATION is terminating action to the PART 9 repeat inspection.
(b) Do corrective action in accordance with Table 3.
Group 3:
Table 6: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH PARTIALLY CAPTURED BOLT
RETENTION CLIP ASSEMBLY - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Do PART 10.MLG center door lower at-
tachment installation config-
uration - partially captured
bolt retention clip assem-
blies installed.
-Before further
flight.
OPTION 1 (ACTION 1):
Remove the MLG center
door assembly retention
clip assemblies.
CONDITION 13: NO
LOOSE, MISSING, DAM-
AGED OR BOTTOMED
OUT ATTACHMENT
BOLTS AND NO WEAR
TO THE RETENTION CLIP
ASSEMBLIES
-Before further
flight.
OPTION 1 (ACTION 2):
Do PART 5. (a)
5,500 flight cycles.
(a)
-OPTION 2: Repeat PART
10.
-Before further
flight.
Do a detailed inspection
and measurement of the
MLG lug bushings for ex-
cessive wear, galling and
any crack.
CONDITION 14: ANY
LOOSE, MISSING, DAM-
AGED OR BOTTOMED
OUT ATTACHMENT
BOLTS, OR ANY WEAR
TO THE RETENTION CLIP
ASSEMBLIES
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
45 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 46

Group 3:
Table 6: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH PARTIALLY CAPTURED BOLT
RETENTION CLIP ASSEMBLY - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
OPTION 1 (ACTION 1):
Do PART 7.
CONDITION 14.1: EXCES-
SIVE WEAR FOUND IN
THE INTERNAL DIAME-
TER OF THE BUSHING
OR ANY GALLING OR
ANY CRACK FOUND
(b)
-Before further
flight.
OPTION 1 (ACTION 2):
Do PART 5. (a)
-Before further
flight.
OPTION 2 (ACTION 1):
Do PART 7. (b)
-Before further
flight.
OPTION 2 (ACTION 2):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 2 (ACTION 3):
Repeat PART 10.
-Before further
flight.
OPTION 3 (ACTION 1):
Remove the center and
inboard door assemblies.
-Before installation
of the center and
inboard door as-
semblies.
OPTION 3 (ACTION 2):
Do PART 7.
(b)
-Before further
flight.
OPTION 3 (ACTION 3):
Do PART 5. (a)
-Before further
flight.
OPTION 4 (ACTION 1):
Remove the center and
inboard door assemblies.
-Before installation
of the center and
inboard door as-
semblies.
OPTION 4 (ACTION 2):
Do PART 7. (b)
-Before further
flight.
OPTION 4 (ACTION 3):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 4 (ACTION 4):
Repeat PART 10.
-Before further
flight.
OPTION 1: Do PART 5.
(a)
CONDITION 14.2: NO EX-
CESSIVE WEAR FOUND
IN THE INTERNAL DIAME-
TER OF THE BUSHING
AND NO GALLING AND
NO CRACK FOUND
-Before further
flight.
OPTION 2 (ACTION 1):
Do PART 6.
5,500 flight cycles.
(a)
-OPTION 2 (ACTION 2):
Repeat PART 10.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
46 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 47

Group 3:
Table 6: MLG CENTER DOOR ASSEMBLY ATTACHMENTS WITH PARTIALLY CAPTURED BOLT
RETENTION CLIP ASSEMBLY - INSPECTION AND MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
(a) Accomplishment of PART 5: MLG CENTER DOOR RETENTION CLIP ASSEMBLIES -
MODIFICATION is terminating action to the PART 10 repeat inspection.
(b) Do corrective action in accordance with Table 3.
F. Approval
NOTE: The approval statement that follows is valid for 737-700C airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved for all airplanes
listed in the service bulletin effectivity. This service bulletin and its approval were based on the airplane
in its original Boeing delivery configuration or as modified by other approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
NOTE: The approval statement that follows is valid for all affected airplanes, except 737-700C
airplanes.
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
47 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 48

Group 1; Group 2, Configuration 1:
Table 1: Detailed Inspection
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
0.500.501FIGURE 1
0.500.501FIGURE 2
0.500.501Restoration
2.002.00TOTAL FOR EACH AIRPLANE
Group 2, Configuration 2:
Table 2: Detailed Inspection
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
0.100.101FIGURE 3
0.100.101FIGURE 4
0.500.501Restoration
1.201.20TOTAL FOR EACH AIRPLANE
Group 1; Group 2, Configuration 1:
Table 3: Repair / Modification
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
1.001.001FIGURE 5
0.750.751FIGURE 6
1.001.001FIGURE 7
0.750.751FIGURE 8
0.600.601FIGURE 13
0.600.601FIGURE 14
0.500.501Restoration
5.70 (a)5.70 (a)TOTAL FOR EACH AIRPLANE
(a) Hours for gear swing (if necessary) are not included.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
48 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 49

Group 2, Configuration 2:
Table 4: Repair / Modification
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
0.600.601FIGURE 9
0.500.501FIGURE 10
0.600.601FIGURE 11
0.500.501FIGURE 12
0.600.601FIGURE 13
0.600.601FIGURE 14
0.500.501Restoration
4.40 (a)4.40 (a)TOTAL FOR EACH AIRPLANE
(a) Hours for gear swing (if necessary) are not included.
Group 3:
Table 5: Main Landing Gear Center Door Lower Attachment Installation Configuration Check
Elapsed HoursTask HoursNumber of PersonsTask
0.100.101On-airplane Check
0.10 (a)0.10 (a)TOTAL FOR EACH AIRPLANE
(a) Maintenance records check is considered lost time. Hours for maintenance
records check are not included.
Group 3:
Table 6: MLG Center Door Assembly Attachments With No Retention Clip Assembly - Detailed
Inspection / Modification
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
0.100.101FIGURE 3
0.100.101FIGURE 4
0.600.601FIGURE 9
0.500.501FIGURE 10
0.600.601FIGURE 11
0.500.501FIGURE 12
0.600.601FIGURE 13
0.600.601FIGURE 14
0.500.501Restoration
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
49 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 50

Group 3:
Table 6: MLG Center Door Assembly Attachments With No Retention Clip Assembly - Detailed
Inspection / Modification
Elapsed HoursTask HoursNumber of PersonsTask
4.604.60TOTAL FOR EACH AIRPLANE
Group 3:
Table 7: MLG Center Door Assembly Attachments With Partially Captured Bolt Retention
Clip Assembly - Detailed Inspection / Modification
Elapsed HoursTask HoursNumber of PersonsTask
0.500.501Preparation
0.500.501FIGURE 1
0.500.501FIGURE 2
1.001.001FIGURE 5
0.750.751FIGURE 6
1.001.001FIGURE 7
0.750.751FIGURE 8
0.600.601FIGURE 13
0.600.601FIGURE 14
0.500.501Restoration
6.706.70TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Letter 737-SL-51-042
b. Boeing Service Related Problem (SRP) 737NG-SRP-52-0101
c. Component Maintenance Manual (CMM) 32-11-12
d. Service Bulletin Index D6-19567
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
50 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 51

e. Standard Overhaul Practices Manual (SOPM) 20-20-01, 20-20-02, 20-30-02, 20-42-02,
20-42-10, 20-50-01, 20-50-03, 20-50-19
f. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 32-00-01, 32-13-11
g. 737NG Fleet Team Digest (FTD) 52-12001
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
FITTING ASSY - INBD, AFT, CENTER MLG DOOR113A8240
FITTING - FWD, INBD, CENTER MAIN LANDING GEAR DOOR113A8241
DOOR INSTL - MAIN LANDING GEAR113A8000
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
32-13737 Aircraft Maintenance Manual
32-11Component Maintenance Manual
32-13737 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
51 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 52

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
52 of 148
BOEING SERVICE BULLETIN 737-52-1170
BLANK PAGE

### Page 53

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits/parts shown in Paragraph 2.C., Parts Necessary for Each Airplane. Operators
are encouraged to share schedule requirements with Boeing for incorporation of the service bulletin.
The kits/parts are subject to the terms and conditions of the Boeing standard purchase order
acknowledgment. Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 1
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 1 date of
this Service Bul-
letin (Calendar
Days)
QTYDateNameKit Number
----TOP KIT002A0003-206
(a)(b)
2,900.00263200
(c)
May 25, 2016REPLACEMENT KIT002A0003-45 (a)
115January 20,
2017
100March 17,
2017
5.00280200
(d)
May 10, 2016SUPPLEMENTAL KIT002A0003-46 (b)
115January 05,
2017
(a) 002A0003-206 was superseded and replaced by 002A0003-45 for operators that have not purchased any
kits.
(b) 002A0003-46 is a supplemental kit for operators that have purchased but not used 002A0003-206 Top
Kit.
(c) A total of 1,800 kits will be available by February 17, 2017. The total will be available in 9 split quantities
of 200 kits.
(d) A total of 1,600 kits will be available by November 29, 2016. The total will be available in 8 split quantities
of 200 kits.
Operators are encouraged to complete the survey provided in APPENDIX E of this service bulletin to
help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
53 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 54

B. Industry Support Information
Boeing warranty remedies are available for 737 airplanes in warranty as of January 26, 2012. For task
hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing Fleet
Support Contracts - Warranty. The kit(s)/ part(s) for airplanes in warranty as of that date will be supplied
at no charge. Send a purchase order for the kit(s)/ part(s) to Boeing Material Management. Please
refer to this service bulletin number and reference the airplane variable number(s) in your purchase
order. The warranty remedies will expire eight years from the original issue date of this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each airplane. The Top Kit is divided into Figure kits for
each installation figure shown in the table below.
Figure Kit
1413Top Kit
11002A0003-45
KIT 002A0003-45
Notes
Existing Part
NumberName
Figure
New Part Number
1413
Qty
(a)LAMINATED SHIM33113A8501-6
(b)FWD RETENTION
CLIP
11113A8501-18
(b)LOWER RETEN-
TION CLIP
11113A8501-21
(b)AFT UPPER RE-
TENTION PLATE
11113A8501-23
(c)BOLT, HEX HEAD22BACB30NM3K13
(c)BOLT11BACB30NM3K5
(d)BOLT, HEX HEAD22BACB30NM6K22
(BACB30NM6HK22
optional)
-NUT33BACN10YR3CD
-WASHER11BACW10BN6UC
-WASHER33BACW10BP3ACU
-WASHER44BACW10P533CA
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
54 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 55

KIT 002A0003-45
Notes
Existing Part
NumberName
Figure
New Part Number
1413
Qty
-WASHER44BACW10P534CA
-WASHER33BACW10P584CG
-WASHER44BACW10P585CG
-WASHER, FLAT33NAS1149D0363J
(a) Discard the existing part.
(b) This part is used in production.
(c) If grip length shown is not available at Boeing, fasteners supplied in kits may
be one grip length longer than indicated. Also, if any fasteners part numbers
listed are not available or have been superseded, substitute fasteners may be
supplied in kits.
(d) Grip length substitution not allowed.
KIT 002A0003-46
NotesNameQtyNew Part Number
-WASHER6BACW10P584CG
-WASHER8BACW10P585CG
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
NotesNameQTYPart Number /
Specification
(a)Grease1 oz.BMS 3-33
(a)Sealant6 oz.BMS 5-95
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
55 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 56

D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
56 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 57

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF
METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE
BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES
CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Airplane Maintenance Manual (AMM).
— Values for electrical maintenance tasks are included in Chapter 20 of
Standard Wiring Practices Manual (SWPM).
— Values for engine maintenance tasks are included in Chapter 70 of 737
Airplane Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
57 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 58

7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. Refer to APPENDIX Athrough APPENDIX C for logic diagrams. Logic diagrams are
provided as an aid only. Information contained in Paragraph 1.E., Compliance is the
primary source for compliance times. Information in Paragraph 3.B., Work Instructions
is the primary source for tasks required for compliance.
10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
13. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
14. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
15. If shading is used, shaded areas in Figures are to separate the non-critical and
non-authoritative information from the critical and authoritative information.
16. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
17. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
18. The CONDITIONS, ACTIONS and OPTIONS shown apply to each side of the airplane
independently.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
58 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 59

19. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. If a step or sub-step is labeled
"RC Exempt," then the RC requirement is removed from that step or sub-step. An
Alternative Method of Compliance (AMOC) is required for any deviations to RC steps,
including sub-steps and identified figures. Steps not labeled as RC may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC. This is provided that
the RC steps, including sub-steps and identified figures, can still be done as specified,
and the airplane can be put back in an airworthy condition.
20. A check of the airplane maintenance records is acceptable for compliance with the
requirements of OPTION 1: MAIN LANDING GEAR (MLG) CENTER DOOR LOWER
ATTACHMENTS MAINTENANCE RECORDS CHECK of Paragraph 3.B., Work
Instructions provided the MLG center door lower attachment installation configuration
can be determined from that check.
B. WORK INSTRUCTIONS
Group 1; Group 2, Configuration 1:
1. Do PART 1: PREPARATION.
2. RC - Do PART 2: MLG CENTER DOOR ASSEMBLY ATTACHMENTS - DETAILED INSPECTION
for any loose, missing, damaged or bottomed out attachment bolts, and any wear to the retention
clip assemblies.
a. CONDITION 1: NO LOOSE, MISSING, DAMAGED OR BOTTOMED OUT ATTACHMENT
BOLTS AND NO WEAR TO THE RETENTION CLIP ASSEMBLIES.
(1) OPTION 1 (ACTION 1): Do PART 4: MLG CENTER DOOR ASSEMBLY ATTACHMENTS
- REMOVAL.
(2) OPTION 1 (ACTION 2): Do PART 5: MLG CENTER DOOR RETENTION CLIP
ASSEMBLIES - MODIFICATION.
NOTE: Accomplishment of the modification in accordance with PART 5 terminates the
repeat inspection requirement.
(3) OPTION 2: Repeat PART 2: MLG CENTER DOOR ASSEMBLY ATTACHMENTS -
DETAILED INSPECTION for any loose, missing, damaged or bottomed out attachment
bolts, and any wear to the retention clip assemblies.
b. CONDITION 2: ANY LOOSE, MISSING, DAMAGED OR BOTTOMED OUT ATTACHMENT
BOLTS, OR ANY WEAR TO THE RETENTION CLIP ASSEMBLIES.
(1) Do PART 3: MLG LUG BUSHINGS - DETAILED INSPECTION/MEASUREMENT for
excessive wear, galling and any crack.
(a) CONDITION 2.1: EXCESSIVE WEAR FOUND IN THE INTERNAL DIAMETER OF
THE BUSHING OR ANY GALLING OR ANY CRACK FOUND.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
59 of 148
BOEING SERVICE BULLETIN 737-52-1170

### Page 60

1) OPTION 1 (ACTION 1): Do PART 7: MLG LUG INSPECTION AND BUSHING
REPLACEMENT.
2) OPTION 1 (ACTION 2): Do PART 5: MLG CENTER DOOR RETENTION CLIP
ASSEMBLIES - MODIFICATION.
NOTE: Accomplishment of the modification in accordance with PART 5
terminates the repeat inspection requirement.
3) OPTION 2 (ACTION 1): Do PART 7: MLG LUG INSPECTION AND BUSHING
REPLACEMENT.
4) OPTION 2 (ACTION 2): Do PART 6: MLG CENTER DOOR ASSEMBLY BOLTS
AND RETENTION CLIP ASSEMBLIES - REPLACEMENT.
5) OPTION 2 (ACTION 3): Repeat PART 2: MLG CENTER DOOR ASSEMBLY
ATTACHMENTS - DETAILED INSPECTION for any loose, missing, damaged
or bottomed out attachment bolts, and any wear to the retention clip assemblies.
6) OPTION 3 (ACTION 1): Remove the center and inboard door assemblies. Refer
to Airplane Flight Manual (AFM), Configuration Deviation List (CDL) to determine
performance limitations and refer to 737-600/700/800/900 AMM 32-13-11 as an
accepted procedure for parts to be removed or left in place.
7) OPTION 3 (ACTION 2): Do PART 7: MLG LUG INSPECTION AND BUSHING
REPLACEMENT.
8) OPTION 3 (ACTION 3): Do PART 5: MLG CENTER DOOR RETENTION CLIP
ASSEMBLIES - MODIFICATION.
NOTE: Accomplishment of the modification in accordance with PART 5
terminates the repeat inspection requirement.
9) OPTION 4 (ACTION 1): Remove the center and inboard door assemblies. Refer
to Airplane Flight Manual (AFM), Configuration Deviation List (CDL) to determine
performance limitations and refer to 737-600/700/800/900 AMM 32-13-11 as an
accepted procedure for parts to be removed or left in place.
10) OPTION 4 (ACTION 2): Do PART 7: MLG LUG INSPECTION AND BUSHING
REPLACEMENT.
11) OPTION 4 (ACTION 3): Do PART 6: MLG CENTER DOOR ASSEMBLY BOLTS
AND RETENTION CLIP ASSEMBLIES - REPLACEMENT.
12) OPTION 4 (ACTION 4): Repeat PART 2: MLG CENTER DOOR ASSEMBLY
ATTACHMENTS - DETAILED INSPECTION for any loose, missing, damaged
or bottomed out attachment bolts, and any wear to the retention clip assemblies.
(b) CONDITION 2.2: NO EXCESSIVE WEAR FOUND IN THE INTERNAL DIAMETER
OF THE BUSHING AND NO GALLING AND NO CRACK FOUND.
1) OPTION 1: Do PART 5: MLG CENTER DOOR RETENTION CLIP ASSEMBLIES
- MODIFICATION.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: July 29, 2014
737-52-1170Revision 1: December 19, 2017
60 of 148
BOEING SERVICE BULLETIN 737-52-1170

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-52-1170/file/7bc73a8bce4f.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
