# Boeing Service Bulletin 737-53-1309: Revision 1, part 1 of 3

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-0919, the docket of a proposed AD (Federal Register 2025-09770). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 737-53-1309](https://openairdocs.org/service-documents/boeing/sb-737-53-1309.md)
- Title as filed: SB-737-53-1309-01_Rev1 -Part1
- Pages: 140
- PDF: https://openairdocs.org/files/sha256/77/94/77941c78ecf20a9fc6995fda54033c1944488b7977aac8f5c7584a43a0b3bc79
- Page: https://openairdocs.org/service-documents/boeing/sb-737-53-1309/file/77941c78ecf2

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-53-1309
Original Issue: October 20, 2011
Revision 1: May 22, 2024
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chem-mill Steps in Crown Skins at Specified Locations - Inspection
and Modification
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
BOEING PROPRIETARY
Copyright © 2024 The Boeing Company
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
1 of 388
5.0

### Page 2

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
2 of 388
BOEING SERVICE BULLETIN 737-53-1309
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 51
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 53
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 59
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FIGURE 1: FIGURE LAYOUT MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
FIGURE 2: FUSELAGE - SKIN - FORWARD ENTRY DOOR AREA - CHEM MILL STEP INSPECTION. 70
FIGURE 3: FUSELAGE - SKIN - FORWARD ENTRY DOOR AREA - INTERNAL MODIFICATION . . 72
FIGURE 4: FUSELAGE - SKIN - FORWARD ENTRY DOOR AREA - POST MODIFICATION INSPECTION
AT OUTER FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
FIGURE 5: FUSELAGE - SKIN - FORWARD ENTRY DOOR AREA - POST MODIFICATION INSPECTION
AT CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
FIGURE 6: FUSELAGE - SKIN - SKIN PAD-UP AREA AT FORWARD ENTRY DOOR - CHEM MILL STEP
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
FIGURE 7: FUSELAGE - SKIN - SKIN PAD-UP AREA AT FORWARD ENTRY DOOR AFT SIDE - INTERNAL
MODIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
3 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 4

FIGURE 8: FUSELAGE - SKIN - SKIN PAD-UP AREA AT FORWARD ENTRY DOOR AFT SIDE - POST
MODIFICATION INSPECTION AT OUTER FASTENER ROWS . . . . . . . . . . . . . . 94
FIGURE 9: FUSELAGE - SKIN - SKIN PAD-UP AREA AT FORWARD ENTRY DOOR AFT SIDE - POST
MODIFICATION INSPECTION AT CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . 96
FIGURE 10: FUSELAGE - SKIN - TCAS ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 98
FIGURE 11: FUSELAGE - SKIN - TCAS ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . 100
FIGURE 12: FUSELAGE - SKIN - TCAS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
FIGURE 13: FUSELAGE - SKIN - TCAS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
FIGURE 14: FUSELAGE - SKIN - ATC ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 108
FIGURE 15: FUSELAGE - SKIN - ATC ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . . 110
FIGURE 16: FUSELAGE - SKIN - ATC ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
FIGURE 17: FUSELAGE - SKIN - ATC ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
FIGURE 18: FUSELAGE - SKIN - TACAN ANTENNA AREA - CHEM MILL STEP INSPECTION . . . 131
FIGURE 19: FUSELAGE - SKIN - TACAN ANTENNA AREA - INTERNAL MODIFICATION . . . . . . 133
FIGURE 20: FUSELAGE - SKIN - TACAN ANTENNA AREA - POST MODIFICATION INSPECTION AT
OUTER FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
FIGURE 21: FUSELAGE - SKIN - TACAN ANTENNA AREA - POST MODIFICATION INSPECTION AT
CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
FIGURE 22: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - LEFT SIDE - CHEM MILL STEP
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
FIGURE 23: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - LEFT SIDE - INTERNAL MODIFICATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
FIGURE 24: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - LEFT SIDE - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . 154
FIGURE 25: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - LEFT SIDE - POST MODIFICATION
INSPECTION AT CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
FIGURE 26: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - RIGHT SIDE - CHEM MILL STEP
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
FIGURE 27: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - RIGHT SIDE - INTERNAL
MODIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
FIGURE 28: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - RIGHT SIDE - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . 174
FIGURE 29: FUSELAGE - SKIN - HIGH GAIN SATCOM ANTENNA - RIGHT SIDE - POST MODIFICATION
INSPECTION AT CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
FIGURE 30: FUSELAGE - SKIN - GPS ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 182
FIGURE 31: FUSELAGE - SKIN - GPS ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . 184
FIGURE 32: FUSELAGE - SKIN - GPS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
FIGURE 33: FUSELAGE - SKIN - GPS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
FIGURE 34: FUSELAGE - SKIN - MLS ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 197
FIGURE 35: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . . 199
FIGURE 36: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
4 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 5

FIGURE 37: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
FIGURE 38: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - CHEM MILL STEP
INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
FIGURE 39: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
FIGURE 40: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . 215
FIGURE 41: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
FIGURE 42: FUSELAGE - SKIN - ELT ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 219
FIGURE 43: FUSELAGE - SKIN - ELT ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . . 221
FIGURE 44: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
FIGURE 45: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
FIGURE 46: FUSELAGE - SKIN - ELT ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 230
FIGURE 47: FUSELAGE - SKIN - ELT ANTENNA AREA - INTERNAL MODIFICATION [Group 2-3] . 232
FIGURE 48: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS [Group 2-3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
FIGURE 49: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP [Group 2-3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
FIGURE 50: FUSELAGE - SKIN - ELT ANTENNA AREA - INTERNAL MODIFICATION [Group 1] . . 241
FIGURE 51: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
FIGURE 52: FUSELAGE - SKIN - ELT ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
FIGURE 53: FUSELAGE - SKIN - ADF ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 250
FIGURE 54: FUSELAGE - SKIN - ADF ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . . 252
FIGURE 55: FUSELAGE - SKIN - ADF ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
FIGURE 56: FUSELAGE - SKIN - ADF ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
FIGURE 57: FUSELAGE - SKIN - ADF ANTENNA AREA - CHEM MILL STEP INSPECTION . . . . . 273
FIGURE 58: FUSELAGE - SKIN - ADF ANTENNA AREA - INTERNAL MODIFICATION . . . . . . . . 275
FIGURE 59: FUSELAGE - SKIN - ADF ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
FIGURE 60: FUSELAGE - SKIN - ADF ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM
MILL STEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
FIGURE 61: FUSELAGE - SKIN - SATCOM AERO I ANTENNA AREA - CHEM MILL STEP INSPECTION
[Group 2-3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
FIGURE 62: FUSELAGE - SKIN - SATCOM AERO I ANTENNA AREA - INTERNAL MODIFICATION [Group
2-3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
FIGURE 63: FUSELAGE - SKIN - SATCOM AERO I ANTENNA AREA - POST MODIFICATION INSPECTION
AT OUTER FASTENER ROWS [Group 2-3] . . . . . . . . . . . . . . . . . . . . . . . . 303
FIGURE 64: FUSELAGE - SKIN - SATCOM AERO I ANTENNA AREA - POST MODIFICATION INSPECTION
AT CHEM MILL STEP [Group 2-3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
FIGURE 65: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(PRE-PRR38432) - CHEM MILL STEP INSPECTION [Group 1-2] . . . . . . . . . . . . . 307
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
5 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 6

FIGURE 66: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(PRE-PRR38432) - INTERNAL AND EXTERNAL MODIFICATION [Group 1-2] . . . . . 309
FIGURE 67: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(PRE-PRR38432) - POST MODIFICATION INSPECTION AT OUTER FASTENER ROWS
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
FIGURE 68: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(PRE-PRR38432) - POST MODIFICATION INSPECTION AT CHEM-MILL STEP [Group 1-2]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
FIGURE 69: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(PRE-PRR38432) - CHEM-MILL STEP INSPECTION [Group 1-2] . . . . . . . . . . . . . 327
FIGURE 70: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(PRE-PRR38432) - INTERNAL AND EXTERNAL MODIFICATION [Group 1-2] . . . . . 329
FIGURE 71: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(PRE-PRR38432) - POST MODIFICATION INSPECTION AT OUTER FASTENER ROWS
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
FIGURE 72: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(PRE-PRR38432) - POST MODIFICATION INSPECTION AT CHEM-MILL STEP [Group 1-2]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
FIGURE 73: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(POST-PRR38432) - CHEM-MILL STEP INSPECTION [Group 3] . . . . . . . . . . . . . 347
FIGURE 74: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(POST-PRR38432) - INTERNAL AND EXTERNAL MODIFICATION [Group 3] . . . . . . 349
FIGURE 75: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(POST-PRR38432) - POST MODIFICATION INSPECTION AT OUTER FASTENER ROWS
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
FIGURE 76: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, LEFT SIDE
(POST-PRR38432) - POST MODIFICATION INSPECTION AT CHEM-MILL STEP [Group 3]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
FIGURE 77: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(POST-PRR38432) - CHEM-MILL STEP INSPECTION [Group 3] . . . . . . . . . . . . . 367
FIGURE 78: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(POST-PRR38432) - INTERNAL AND EXTERNAL MODIFICATION [Group 3] . . . . . . 369
FIGURE 79: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(POST-PRR38432) - POST MODIFICATION INSPECTION AT OUTER FASTENER ROWS
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
FIGURE 80: FUSELAGE - SKIN - SKIN PAD-UP AT OVERWING DOOR STRUCTURE, RIGHT SIDE
(POST-PRR38432) - POST MODIFICATION INSPECTION AT CHEM-MILL STEP [Group 3]
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
APPENDIX A: NON DESTRUCTIVE INSPECTION (NDI) AREA . . . . . . . . . . . . . . . . . . . . . . 387
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
6 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 7

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-53-1309Original Issue: October 20, 2011
Revision 1: May 22, 2024
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chem-mill Steps in Crown Skins at Specified Locations - Inspection
and Modification
This revision includes all pages of the Service Bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-08-08 is related to this Service Bulletin.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this Service Bulletin. The Airworthiness Directive will make the compliance tasks and times given in this Service
Bulletin mandatory.
Effects of this Revision on airplanes on which Original Issue was previously done:
None. However, the Boeing compliance recommendation compliance times/intervals have been changed. It is
recommended for operators to review and update their maintenance program accordingly.
REASON FOR REVISION
This revision is sent to change the compliance times/intervals for the initial inspection, repeat inspections and
post modification inspections.
The Service Bulletin was also changed to Special Attention to reduce inspection threshold and intervals. Existing
Service Bulletin repeat inspections are not adequate because new fleet data indicates that crack growth is faster
and more distributed between tear straps, resulting in longer cracks, than originally observed in the test data
that was the basis for the Service Bulletin. Existing Service Bulletin inspection threshold for the pocket-pad
chem-mill step may not be adequate because new fleet data indicates that the crack initiation occurs earlier
than the Service Bulletin threshold.
These sections were changed:
1. Summary, Background: Updated statement and added Boeing Service Related Problem (SRP) and
Boeing Fleet Team Digest (FTD) references.
2. Summary, Compliance: Is updated to show a new Federal Aviation Administration (FAA) Airworthiness
Directive number.
3. Paragraph 1.C., Reason: Updated statement and added Boeing Service Related Problem (SRP) and
Boeing Fleet Team Digest (FTD) references. Added reason for revision statement.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
7 of 388

### Page 8

4. Paragraph 1.D., Description: Added the effects of this revision on airplanes on which Original Issue
was previously done statement.
5. Paragraph 1.E., Compliance: Updated to show a new Federal Aviation Administration (FAA)
Airworthiness Directive number and updated existing compliance tables to new format, changed
compliance times and repeat intervals.
6. Paragraph 1.F., Approval: updated statement and added Alternative Method of Compliance (AMOC)
statement.
7. Paragraph 1.J.1., Existing Data: Added references to show new Boeing Service Related Problem
(SRP), Boeing Fleet Team Digest (FTD), Federal Aviation Administration (FAA) Airworthiness Directive,
Engineering Change Memo and 737 Non-Destructive Testing (NDT) Manual.
8. Paragraph 1.M., Software Accomplishment Summary: New section added but not affected.
9. Paragraph 2.C.2., Parts and Materials Supplied by the Operator: updated tables.
10. Paragraph 3.A.,General Information: Added note 12 and 13.
11. Paragraph 3.B.,Work Instructions: Incorporated compliance table changes. Removed references to
compliance times in the work instructions.
12. Figure 1: Table is updated.
13. Figures 2, 6, 10, 14, 18, 22, 26, 30, 34, 38, 42, 46, 53, 57, 61, 65, 69, 73, and 77: Added new footnote
for alternative Non-Destructive Test (NDT) procedure.
14. Figure 19: Added new note.
15. Figure 54: Updated illustrations and footnotes.
16. Appendix A: Added title.
The data given in Alternative Method of Compliance Notice 737-53-1309 AMOC01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
October 20, 2011Original Issue:
May 22, 2024Revision 1:
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
8 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 9

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-53-1309Original Issue: October 20, 2011
Revision 1: May 22, 2024
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chem-mill Steps in Crown Skins at Specified Locations - Inspection
and Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This Service Bulletin is sent to give instructions to inspect the fuselage skin and install modification doublers at
specified locations where chem-mill areas are adjacent to non chem-mill areas at antenna and door bearstrap
installations. These actions are necessary to find and repair, or prevent fatigue cracking of the skin panel at the
specified chem-mill step locations which could result in rapid decompression of the airplane.
Boeing received reports of early fatigue cracks near chem-mill areas on the crown skin panels of
737-300/-400/-500 airplanes. The cracks resulted from high stresses in the areas where chem-mill pockets are
adjacent to non chem-mill areas. Since the original issue of this Service Bulletin, 3 cases of suspected fuselage
fatigue cracks were reported adjacent to non chem-milled skin bays on 737-700 airplanes with between 40,000
and 43,000 airframe flight cycles.
Boeing had not received reports of fuselage fatigue cracks on 737-600/-700/-700C/-800/-900/-900ER airplanes
at the time of the original issue of this Service Bulletin. However, a full scale fatigue test was conducted and the
test airplane was inspected for skin cracks at similar structural details and two cracks were found that occurred
late in the testing program. The 737-600 crown skin panels are of similar design to those of the 737-300/-400/-500
airplanes.
Boeing Service Related Problem (SRP) 737NG-SRP-53-0370 and 737NG-SRP-53-0626 are related to this
Service Bulletin.
Boeing Fleet Team Digest (FTD) 737NG-FTD-53-11001 and 737NG-FTD-53-20003 are related to this Service
Bulletin.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
9 of 388

### Page 10

ACTION (PRR 38945, PRR 39800-026RS)
Get external access to the areas of the crown skin at the specified antenna locations, the forward passenger
door bearstrap and the emergency exit bearstraps. Do an external detailed inspection and an external Non
Destructive Inspection (NDI) for cracking in the fuselage skin along the chem-mill steps at these locations. The
NDI methods that can be used are Medium Frequency Eddy Current (MFEC), Magneto Optical Imaging (MOI),
C-Scan or Ultrasonic Phased Array (UTPA). At each location, if any crack is found, contact Boeing for further
instructions and do the work instructed by Boeing. If no cracking is found, install the modification doublers and
fillers or repeat the inspections at the specified intervals given in Paragraph 1.E., Compliance. After
accomplishment of the modification, post modification inspections will be necessary.
EFFECTIVITY
737-600 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-08-08 is related to this Service Bulletin.
The effective date of AD 2013-08-08 is May 24, 2013.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive related to
this Service Bulletin. The Airworthiness Directive will make the compliance tasks and times given in this Service
Bulletin mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, and/or modification procedures given in this
Service Bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
10 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 11 (OCR)

BOEING SERVICE BULLETIN 737-53-1309
STA
887
STA
727
STA  000000000
360
DO AN EXTERNAL DETAILED INSPECTION AND AN
EXTERNAL NON DESTRUCTIVE INSPECTION (NDI)
S-10R  FOR CRACKING IN THE FUSELAGE SKIN ALONG THE
CHEM-MILL STEPS AT THE SPECIFIED LOCATIONS IN
THE CROWN SKIN
INSTALL MODIFICATION FILLERS AND DOUBLERS AT
THE CHEM-MILL STEP. DO POST MODIFICATION
INSPECTIONS AT ALL MODIFIED LOCATIONS.
STA  STA  STA  STA  STA
294.5  312  328  344  360
S-1
• S-2L
- S-3L
EXAMPLE CRACK
• INSPECTION AREA  LOOKING INBOARD  FWD  2066539
FORWARD ENTRY DOOR AREA PAD-UP SHOWN OTHER LOCATIONS SIMILAR
Original Issue: October 20, 2011
Revision 1: May 22, 2024  737-53-1309
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  11 of 388

### Page 12

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
12 of 388
BOEING SERVICE BULLETIN 737-53-1309
BLANK PAGE

### Page 13

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-53-1309
Original Issue: October 20, 2011
Revision 1: May 22, 2024
ATA System: 5331
SUBJECT: FUSELAGE - Skin - Chem-mill Steps in Crown Skins at Specified Locations - Inspection
and Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This bulletin is applicable to 737-600 Airplane(s), line number(s) 21, 30, 49, 92, 100, 112, 116,
120, 137, 149, 191, 193, 209, 227, 243, 255, 257, 268, 270, 282, 290, 303, 310, 329-330, 333,
335, 368, 375, 382, 407, 447, 510, 526, 543, 546, 563, 614, 816, 887, 932, 938, 1115, 1131, 1150,
1152, 1164, 1276, 1294, 1305, 1378, 1400, 1415, 1437, 1455, 1508, 1759, 1797, 1816, 1862,
1884, 1912, 1931, 1956, 2004, 2016, 2022, 2032, 2045 in 3 Group(s). Where the effectivity is
presented with hyphens between line numbers, the airplane applicability means "through" and
"inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
Refer to Service Bulletin Index D6-19567 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This Service Bulletin is for the airplane(s) shown below. An equivalent change is on subsequent
production airplanes. Refer to PRR 38945 and PRR 39800-026RS for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
737-600 airplanes that do not have a SATCOM Aero I antenna.- 1
737-600 airplanes with Overwing Exit Pre-PRR 38432.- 2
737-600 airplanes with Overwing Exit Post-PRR 38432.- 3
Airplane Models:
737-600
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
13 of 388

### Page 14

GroupVariable Number
1YE001 - YE002
2YE003 - YE020
2YE051
2YE101 - YE109
GroupVariable Number
2YE151 - YE157
2YE171 - YE172
3YE201 - YE206
3YE301 - YE305
GroupVariable Number
3YE321 - YE326
3YE371 - YE383
--
--
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
This Service Bulletin is sent to give instructions to inspect the fuselage skin and install modification
doublers at specified locations where chem-mill areas are adjacent to non chem-mill areas at antenna
and door bearstrap installations. These actions are necessary to find and repair, or prevent fatigue
cracking of the skin panel at the specified chem-mill step locations which could result in rapid
decompression of the airplane.
Boeing received reports of early fatigue cracks near chem-mill areas on the crown skin panels of
737-300/-400/-500 airplanes. The cracks resulted from high stresses in the areas where chem-mill
pockets are adjacent to non chem-mill areas. Since the original issue of this Service Bulletin, 3 cases
of suspected fuselage fatigue cracks were reported adjacent to non chem-milled skin bays on 737-700
airplanes with between 40,000 and 43,000 airframe flight cycles.
Boeing had not received reports of fuselage fatigue cracks on 737-600/-700/-700C/-800/-900/-900ER
airplanes at the time of the original issue of this Service Bulletin. However, a full scale fatigue test was
conducted and the test airplane was inspected for skin cracks at similar structural details and two cracks
were found that occurred late in the testing program. The 737-600 crown skin panels are of similar
design to those of the 737-300/-400/-500 airplanes.
Boeing Service Related Problem (SRP) 737NG-SRP-53-0370 and 737NG-SRP-53-0626 are related
to this Service Bulletin.
Boeing Fleet Team Digest (FTD)  737NG-FTD-53-11001 and 737NG-FTD-53-20003 are related to this
Service Bulletin.
Revision 1 is sent to change the compliance times/intervals for the initial inspection, repeat inspections
and post modification inspections. The Service Bulletin was also changed to Special Attention to reduce
inspection intervals. Existing Service Bulletin repeat inspections are not adequate because new fleet
data indicates that crack growth is faster and more distributed between tear straps, resulting in longer
cracks, than originally observed in the test data that was the basis for the Service Bulletin.
The data given in Alternative Method of Compliance Notice 737-53-1309AMOC01 is included in this
revision.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
14 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 15

D. Description
Get external access to the areas of the crown skin at the specified antenna locations, the forward
passenger door bearstrap and the emergency exit bearstraps. Do an external detailed inspection and
an external Non Destructive Inspection (NDI) for cracking in the fuselage skin along the chem-mill steps
at these locations. The NDI methods that can be used are Medium Frequency Eddy Current (MFEC),
Magneto Optical Imaging (MOI), C-Scan or Ultrasonic Phased Array (UTPA). At each location, if any
crack is found, contact Boeing for further instructions and do the work instructed by Boeing. If no
cracking is found, install the modification doublers and fillers or repeat the inspections at the specified
intervals given in Paragraph 1.E., Compliance. After accomplishment of the modification, post
modification inspections will be necessary.
Effects of this Revision on airplanes on which Original Issue was previously done:
None. However, the Boeing compliance recommendation compliance times/intervals have been changed.
It is recommended for operators to review and update their maintenance program accordingly.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
221, 222, 231, 232, 241, 242737-600
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-08-08 is related to this Service
Bulletin. The effective date of AD 2013-08-08 is May 24, 2013.
The Federal Aviation Administration (FAA) will possibly release an additional Airworthiness Directive
related to this Service Bulletin. The Airworthiness Directive will make the compliance tasks and times
given in this Service Bulletin mandatory.
Accomplish the required action(s), based on the applicable condition(s) in Table(s) 1 through 3, in
accordance with Paragraph 3. Accomplishment Instructions.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for
that CONDITION or OPTION.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
15 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 16

Table 1: Fuselage skin inspections at chem-mill steps in specific pocket to no pocket areas
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Whichever occurs first:Before 37,000
total flight cy-
cles.
OPTION 1 :
Do an external Detailed
inspection and do an ex-
ternal Medium Frequency
Eddy Current (MFEC) or
Magneto Optic Imager
(MOI) or C-Scan inspec-
tion for cracking in the
fuselage skin at the
chem-mill steps at speci-
fied locations in accor-
dance with Accomplish-
ment Instruction 3.B.2.a.
(a)(b)
ALL AIRPLANES
1. Within 600 flight cycles
after the Revision 1 date
of this Service Bulletin.
2. If the last inspection
was an Option 1 inspec-
tion accomplished in ac-
cordance with Accom-
plishment Instruction
3.B.2.a. of the original is-
sue of this Service Bul-
letin: within 1,500 flight
cycles after the last Op-
tion 1 inspection.
3. If the last inspection
was an Option 2 inspec-
tion accomplished in ac-
cordance with Accom-
plishment Instruction
3.B.2.a. of the original is-
sue of this Service Bul-
letin: within 2,100 flight
cycles after the last Op-
tion 2 inspection.
OPTION 2 :
Do an external Detailed
inspection and do an ex-
ternal Ultrasonic Phased
Array Inspection (UTPA)
for cracking in the fuse-
lage skin at the chem-mill
steps at specified loca-
tions in accordance with
Accomplishment Instruc-
tion 3.B.2.a. (a)(b)
-Before further flight.Contact Boeing for fur-
ther instructions and do
the work instructed by
Boeing.
CONDITION 1:
ANY CRACK FOUND
IN THE SKIN.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
16 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 17

Table 1: Fuselage skin inspections at chem-mill steps in specific pocket to no pocket areas
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
600 flight cycles-OPTION 1:CONDITION 2:
(c)(d)Repeat external detailed
inspection and external
Medium Frequency Eddy
Current (MFEC) or Mag-
neto Optic Imager (MOI)
or C-Scan inspection for
cracking in the fuselage
skin at the chem-mill
steps at specified loca-
tions in accordance with
Accomplishment Instruc-
tion 3.B.2.a. (a)(b)
NO CRACK FOUND
AS A RESULT OF
OPTION 1 INSPEC-
TIONS
(d)(e)Within 600 flight cycles after the most re-
cent OPTION 1 inspection was done.
OPTION 2:
Do an external Detailed
inspection and external
Ultrasonic Phased Array
Inspection (UTPA) for
cracking in the fuselage
skin at the chem-mill
steps at specified loca-
tions in accordance with
Accomplishment Instruc-
tion 3.B.2.a. (a)(b)
(d)(e)Within 1,200 flight cycles after the most
recent OPTION 2 inspection was done.
OPTION 1:
Do an external detailed
inspection and external
Medium Frequency Eddy
Current (MFEC) or Mag-
neto Optic Imager (MOI)
or C-Scan inspection for
cracking in the fuselage
skin at the chem-mill
steps at specified loca-
tions in accordance with
Accomplishment Instruc-
tion 3.B.2.a. (a)(b)
CONDITION 3:
NO CRACK FOUND
AS A RESULT OF
OPTION 2 INSPEC-
TIONS
1,200 flight cy-
cles(c)(d)
-OPTION 2:
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
17 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 18

Table 1: Fuselage skin inspections at chem-mill steps in specific pocket to no pocket areas
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
Repeat external detailed
inspection and external
Ultrasonic Phased Array
Inspection (UTPA) for
cracking in the fuselage
skin at the chem-mill
steps at specified loca-
tions in accordance with
Accomplishment Instruc-
tion 3.B.2.a. (a)(b)
(a) It is not necessary to inspect the chem-mill steps under an existing external repair doubler provided: (1)
The repair was installed after the original issue date of this Service Bulletin; (2) The repair was approved
by the FAA or by a Boeing company authorized representative who was authorized by the FAA to make
such findings; and (3) The repair extends a minimum of three rows of fasteners on each side of the chem-
mill line in the circumferential direction.
(b) MOI and C-Scan inspections cannot be used within 4 inches of the edge of an existing external part.
Within 4 inches of the edge of an existing external part, the MFEC or UTPA inspection must be used.
(c) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION. Operators must comply with the compliance time given for
the chosen OPTION under this CONDITION.
(d) Accomplishment of the modification in accordance with Accomplishment Instructions 3.B.3.a. terminates
the repeat inspections. Post-modification inspections are specified in Tables 2 and 3 of Paragraph 1.E.,
Compliance.
(e) Refer to the applicable CONDITION for further ACTIONS.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
18 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 19

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 3,700 flight
cycles after the
modification is in-
stalled.
Whichever occurs
first:
1. Within 3,700
flight cycles after
the Revision 1
date of this Ser-
vice Bulletin.
Before 50,000 to-
tal flight cycles.
OPTION 1:
Do an external
Low Frequency
Eddy Current
(LFEC) inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
ALL AIRPLANES
WITH EXTER-
NAL MODIFICA-
TIONS IN-
STALLED IN AC-
CORDANCE
WITH THIS SER-
VICE BULLETIN. 2. If the last inspec-
tion was an LFEC
inspection accom-
plished in accor-
dance with Accom-
plishment Instruc-
tion 3.B.5.a. of the
original issue of
this Service Bul-
letin: within 3,900
flight cycles after
the last LFEC in-
spection.
OPTION 2:
Do an internal
High Frequency
Eddy Current
(HFEC) inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
3. If the last inspec-
tion was an HFEC
inspection accom-
plished in accor-
dance with Accom-
plishment Instruc-
tion 3.B.5.a. of the
original issue of
this Service Bul-
letin: within 19,000
flight cycles after
the last HFEC in-
spection.
OPTION 3 (AC-
TION 1):
Do an external
LFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
OPTION 3 (AC-
TION 2):
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
19 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 20

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
Do an internal
HFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
20 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 21

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
-Within 2,100 flight
cycles after the
modification is in-
stalled.
Whichever occurs
first:
1. Within 2,100
flight cycles after
the Revision 1
date of this Ser-
vice Bulletin.
Within 28,000
flight cycles after
the modification is
installed, or before
50,000 total flight
cycles, whichever
occurs first.
OPTION 4:
Do an external de-
tailed inspection of
the fuselage skin
for cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
ALL AIRPLANES
WITH INTERNAL
MODIFICATIONS
INSTALLED IN
ACCORDANCE
WITH THIS SER-
VICE BULLETIN.
2. If the last inspec-
tion was a detailed
inspection accom-
plished in accor-
dance with Accom-
plishment Instruc-
tion 3.B.5.b.(1) of
the original issue
of this Service Bul-
letin: within 4,500
flight cycles after
the last detailed
inspection.
OPTION 5:
Do an external
HFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
filler in accordance
with Accomplish-
ment Instructions
3.B.5.b.(1).
3. If the last inspec-
tion was an HFEC
inspection accom-
plished in accor-
dance with Accom-
plishment Instruc-
tion 3.B.5.b.(1) of
the original issue
of this Service Bul-
letin: within 14,000
flight cycles after
the last HFEC in-
spection.
OPTION 6 (AC-
TION 1):
Do an external de-
tailed inspection of
the fuselage skin
for cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
OPTION 6 (AC-
TION 2):
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
21 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 22

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
Do an external
HFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
filler in accordance
with Accomplish-
ment Instructions
3.B.5.b.(1).
-Before further flight.Contact Boeing for
further instructions
and do the work
instructed by Boe-
ing.
CONDITION 1:
ANY CRACK
FOUND IN THE
SKIN.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
22 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 23

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
3,700 flight
cycles. (a)
-OPTION 1: Re-
peat external
LFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
CONDITION 2:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 1 INSPEC-
TION
(b)Within 3,700 flight cycles after the most recent OPTION 1
inspection was done.
OPTION 2: Do an
internal HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
(b)Within 3,700 flight cycles after the most recent OPTION 1
inspection was done.
OPTION 3 (AC-
TION 1): Do an
external LFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
(b)Within 3,700 flight cycles after the most recent OPTION 1
inspection was done.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
23 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 24

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 3 (AC-
TION 2): Do an in-
ternal HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
24 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 25

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(b)Within 11,000 flight cycles after the most recent OPTION
2 inspection was done.
OPTION 1: Do an
external LFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
CONDITION 3:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 2 INSPEC-
TION
11,000
flight cy-
cles. (a)
-OPTION 2: Re-
peat internal
HFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
doubler in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.a.
(b)Within 11,000 flight cycles after the most recent OPTION
2 inspection was done.
OPTION 3 (AC-
TION 1): Do an
external LFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
(b)Within 11,000 flight cycles after the most recent OPTION
2 inspection was done.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
25 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 26

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 3 (AC-
TION 2): Do an in-
ternal HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
26 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 27

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(b)Within 5,500 flight cycles after the most recent OPTION 3
(ACTION 1) and OPTION 3 (ACTION 2) inspections were
both done at least once.
OPTION 1: Do an
external LFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
CONDITION 4:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 3 INSPEC-
TION
(b)Within 5,500 flight cycles after the most recent OPTION 3
(ACTION 1) and OPTION 3 (ACTION 2) inspections were
both done at least once.
OPTION 2: Do an
internal HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
5,500 flight
cycles. (a)
-OPTION 3 (AC-
TION 1): Repeat
external LFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
24,000
flight cy-
cles. (a)
-
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
27 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 28

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 3 (AC-
TION 2): Repeat
internal HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification dou-
bler in accordance
with Accomplish-
ment Instructions
3.B.5.a.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
28 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 29

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
2,100 flight
cycles. (a)
-OPTION 4: Re-
peat external de-
tailed inspection of
the fuselage skin
for cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
CONDITION 5:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 4 INSPEC-
TION
(b)Within 2,100 flight cycles after the most recent OPTION 4
inspection was done.
OPTION 5: Do an
external HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
(b)Within 2,100 flight cycles after the most recent OPTION 4
inspection was done.
OPTION 6 (AC-
TION 1): Do an
external detailed
inspection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
(b)Within 2,100 flight cycles after the most recent OPTION 4
inspection was done.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
29 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 30

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 6 (AC-
TION 2): Do an
external HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
30 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 31

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(b)Within 4,700 flight cycles after the most recent OPTION 5
inspection was done.
OPTION 4: Do an
external detailed
inspection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
CONDITION 6:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 5 INSPEC-
TION
4,700 flight
cycles. (a)
-OPTION 5: Re-
peat external
HFEC inspection
of the fuselage
skin for cracking at
the outer row of
fasteners common
to the modification
filler in accordance
with Accomplish-
ment Instructions
3.B.5.b.(1).
(b)Within 4,700 flight cycles after the most recent OPTION 5
inspection was done.
OPTION 6 (AC-
TION 1): Do an
external detailed
inspection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
(b)Within 4,700 flight cycles after the most recent OPTION 5
inspection was done.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
31 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 32

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 6 (AC-
TION 2): Do an
external HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
32 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 33

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
(b)Within 600 flight cycles after the most recent OPTION 6
(ACTION 1) inspection was done.
OPTION 4: Do an
external detailed
inspection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
CONDITION 7:
NO CRACK
FOUND AS A
RESULT OF OP-
TION 6 INSPEC-
TION
(b)Within 3,900 flight cycles after the most recent OPTION 6
(ACTION 2) inspection was done.
OPTION 5: Do an
external HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
3,600 flight
cycles. (a)
-OPTION 6 (AC-
TION 1): Repeat
external detailed
inspection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
5,500 flight
cycles. (a)
-
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
33 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 34

Table 2: Post Modification Inspection of the fuselage skin at outer fastener rows common to the modifi-
cation parts
Repeat In-
terval (Not
to Exceed)
Compliance Time (Whichever Occurs Later)ActionCondition
OPTION 6 (AC-
TION 2): Repeat
external HFEC in-
spection of the
fuselage skin for
cracking at the
outer row of fasten-
ers common to the
modification filler
in accordance with
Accomplishment
Instructions
3.B.5.b.(1).
(a) After the accomplishment of this OPTION, it is acceptable to change the repeat action from this OPTION
to any other OPTION under this CONDITION. Operators must comply with the compliance time given for
the chosen OPTION under this CONDITION.
(b) Refer to the applicable CONDITION for further ACTIONS.
Table 3: Post Modification inspection of the fuselage skin at the Chem-mill step
Repeat Interval (Not
to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Within 600 flight cy-
cles after the Revi-
sion 1 date of this
Service Bulletin, or
within 5,500 flight cy-
cles after the last in-
spection accom-
plished in accor-
dance with the origi-
nal issue of this Ser-
vice Bulletin,
whichever occurs
first.
Before 50,000 total
flight cycles.
Do an external Non
Destructive Inspec-
tion (NDI) for crack-
ing in the fuselage
skin at the chem-mill
step at the specified
locations in accor-
dance with Accom-
plishment Instruc-
tions 3.B.5.b.(2).
ALL AIRPLANES
WITH INTERNAL
MODIFICATIONS
THAT WERE IN-
STALLED IN AC-
CORDANCE WITH
THIS SERVICE
BULLETIN BEFORE
22,400 TOTAL
FLIGHT CYCLES.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
34 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 35

Table 3: Post Modification inspection of the fuselage skin at the Chem-mill step
Repeat Interval (Not
to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
-Within 600 flight cy-
cles after the Revi-
sion 1 date of this
Service Bulletin, or
within 5,500 flight cy-
cles after the last in-
spection accom-
plished in accor-
dance with the origi-
nal issue of this Ser-
vice Bulletin,
whichever occurs
first.
Before 41,000 total
flight cycles.
Do an external NDI
for cracking in the
fuselage skin at the
chem-mill step at the
specified locations in
accordance with Ac-
complishment Instruc-
tions 3.B.5.b.(2).
ALL AIRPLANES
WITH INTERNAL
MODIFICATIONS
THAT WERE IN-
STALLED IN AC-
CORDANCE WITH
THIS SERVICE
BULLETIN AFTER
22,399 TOTAL
FLIGHT CYCLES
BUT BEFORE
32,001 TOTAL
FLIGHT CYCLES.
-Within 600 flight cy-
cles after the Revi-
sion 1 date of this
Service Bulletin, or
within 5,500 flight cy-
cles after the last in-
spection accom-
plished in accor-
dance with the origi-
nal issue of this Ser-
vice Bulletin,
whichever occurs
first.
Within 5,500 flight
cycles after the modi-
fication doubler is in-
stalled.
Do an external NDI
for cracking in the
fuselage skin at the
chem-mill step at the
specified locations in
accordance with Ac-
complishment Instruc-
tions 3.B.5.b.(2).
ALL AIRPLANES
WITH INTERNAL
MODIFICATIONS
THAT WERE IN-
STALLED IN AC-
CORDANCE WITH
THIS SERVICE
BULLETIN AFTER
32,000 TOTAL
FLIGHT CYCLES.
--Before further flight.Contact Boeing for
further instructions
and do the work in-
structed by Boeing.
CONDITION 1:
ANY CRACK
FOUND IN THE
SKIN.
5,500 flight cycles.-Repeat external NDI
for cracking in the
fuselage skin at the
chem-mill step at the
specified locations in
accordance with Ac-
complishment Instruc-
tions 3.B.5.b.(2).
CONDITION 2:
NO CRACK FOUND
IN THE SKIN.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
35 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 36

F. Approval
This Service Bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this Service Bulletin comply with the applicable regulations and are FAA approved, as well as
European Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all
EASA/JAA approved airplanes listed in the Service Bulletin effectivity. This Service Bulletin and its
approval were based on the airplane in its original Boeing delivery configuration or as modified by other
approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this Service Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Service Bulletin.
In addition, the Manager of the Continued Operational Safety Branch approves the accomplishment
of the inspections and modifications defined in this Service Bulletin revision as an alternative method
of compliance to accomplishing the inspections and modifications of paragraphs (g) and (i) of AD
2013-08-08. All provisions of AD 2013-08-08 that are not specifically referenced in the above statement
remain fully applicable and must be complied with accordingly.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection and modification
for each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate
with operator task hour data if necessary. The estimate does not include lost time. These are some
examples of lost time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Group 1:
Table 1: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.002.001FIGURE 2
1.001.001FIGURE 6
1.501.501FIGURE 10
2.505.002FIGURE 14
1.501.501FIGURE 18
2.502.501FIGURE 22
2.502.501FIGURE 26
1.501.501FIGURE 30
1.501.501FIGURE 34
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
36 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 37

Group 1:
Table 1: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.501.501FIGURE 38
1.501.501FIGURE 42
1.501.501FIGURE 46
2.254.502FIGURE 53
2.752.751FIGURE 57
2.002.001FIGURE 65
2.002.001FIGURE 69
1.001.001Close Access
32.0036.75TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 1:
Table 2: Modification
Elapsed HoursTask HoursNumber of PersonsTask
13.50108.008Open Access
2.002.001FIGURE 2
8.5017.002FIGURE 3
1.001.001FIGURE 6
4.759.502FIGURE 7
1.501.501FIGURE 10
4.509.002FIGURE 11
2.505.002FIGURE 14
15.0060.004FIGURE 15
1.501.501FIGURE 18
4.5018.004FIGURE 19
2.502.501FIGURE 22
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
37 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 38

Group 1:
Table 2: Modification
Elapsed HoursTask HoursNumber of PersonsTask
9.0036.004FIGURE 23
2.502.501FIGURE 26
9.0036.004FIGURE 27
1.501.501FIGURE 30
9.5038.004FIGURE 31
1.501.501FIGURE 34
4.7519.004FIGURE 35
1.501.501FIGURE 38
4.7519.004FIGURE 39
1.501.501FIGURE 42
4.7519.004FIGURE 43
1.501.501FIGURE 46
4.7519.004FIGURE 50
2.254.502FIGURE 53
14.5087.006FIGURE 54
2.752.751FIGURE 57
13.2553.004FIGURE 58
2.002.001FIGURE 65
17.5070.004FIGURE 66
2.002.001FIGURE 69
17.5070.004FIGURE 70
16.50132.008Close Access
206.50854.25TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)(e)(f)
(a) Estimates do not include time to manufacture parts. Time to manufacture parts is con-
sidered lost time in Boeing estimates.
(b) Totals shown do not include time to test disturbed systems.
(c) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(d) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(e) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
38 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 39

Group 1:
Table 2: Modification
Elapsed HoursTask HoursNumber of PersonsTask
(f) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 1:
Table 3: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.502.501FIGURE 4
0.800.801FIGURE 5
0.750.751FIGURE 8
0.750.751FIGURE 9
1.751.751FIGURE 12
0.750.751FIGURE 13
3.006.002FIGURE 16
1.201.201FIGURE 17
1.501.501FIGURE 20
1.501.501FIGURE 21
3.003.001FIGURE 24
3.003.001FIGURE 25
3.003.001FIGURE 28
3.003.001FIGURE 29
3.003.001FIGURE 32
3.003.001FIGURE 33
1.501.501FIGURE 36
1.501.501FIGURE 37
1.501.501FIGURE 40
1.501.501FIGURE 41
1.501.501FIGURE 44
1.501.501FIGURE 45
1.501.501FIGURE 51
1.501.501FIGURE 52
3.406.802FIGURE 55
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
39 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 40

Group 1:
Table 3: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
3.406.802FIGURE 56
2.104.202FIGURE 59
2.104.202FIGURE 60
3.256.502FIGURE 67
0.750.751FIGURE 68
3.256.502FIGURE 71
0.750.751FIGURE 72
1.001.001Close Access
65.5086.00TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 2:
Table 4: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.002.001FIGURE 2
1.001.001FIGURE 6
1.501.501FIGURE 10
2.505.002FIGURE 14
1.501.501FIGURE 18
2.502.501FIGURE 22
2.502.501FIGURE 26
1.501.501FIGURE 30
1.501.501FIGURE 34
1.501.501FIGURE 38
1.501.501FIGURE 42
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
40 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 41

Group 2:
Table 4: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.501.501FIGURE 46
2.254.502FIGURE 53
2.752.751FIGURE 57
1.501.501FIGURE 61
2.002.001FIGURE 65
2.002.001FIGURE 69
1.001.001Close Access
33.5038.25TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 2:
Table 5: Modification
Elapsed HoursTask HoursNumber of PersonsTask
13.50108.008Open Access
2.002.001FIGURE 2
8.5017.002FIGURE 3
1.001.001FIGURE 6
4.759.502FIGURE 7
1.501.501FIGURE 10
4.509.002FIGURE 11
2.505.002FIGURE 14
15.0060.004FIGURE 15
1.501.501FIGURE 18
4.5018.004FIGURE 19
2.502.501FIGURE 22
9.0036.004FIGURE 23
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
41 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 42

Group 2:
Table 5: Modification
Elapsed HoursTask HoursNumber of PersonsTask
2.502.501FIGURE 26
9.0036.004FIGURE 27
1.501.501FIGURE 30
9.5038.004FIGURE 31
1.501.501FIGURE 34
4.7519.004FIGURE 35
1.501.501FIGURE 38
4.7519.004FIGURE 39
1.501.501FIGURE 42
4.7519.004FIGURE 43
1.501.501FIGURE 46
4.7519.004FIGURE 47
2.254.502FIGURE 53
14.5087.006FIGURE 54
2.752.751FIGURE 57
13.2553.004FIGURE 58
1.501.501FIGURE 61
9.5038.004FIGURE 62
2.002.001FIGURE 65
17.5070.004FIGURE 66
2.002.001FIGURE 69
17.5070.004FIGURE 70
16.50132.008Close Access
217.50893.75TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)(e)(f)
(a) Estimates do not include time to manufacture parts. Time to manufacture parts is con-
sidered lost time in Boeing estimates.
(b) Totals shown do not include time to test disturbed systems.
(c) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(d) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(e) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
42 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 43

Group 2:
Table 5: Modification
Elapsed HoursTask HoursNumber of PersonsTask
(f) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 2:
Table 6: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.502.501FIGURE 4
0.800.801FIGURE 5
0.750.751FIGURE 8
0.750.751FIGURE 9
1.751.751FIGURE 12
0.750.751FIGURE 13
3.006.002FIGURE 16
1.201.201FIGURE 17
1.501.501FIGURE 20
1.501.501FIGURE 21
3.003.001FIGURE 24
3.003.001FIGURE 25
3.003.001FIGURE 28
3.003.001FIGURE 29
3.003.001FIGURE 32
3.003.001FIGURE 33
1.501.501FIGURE 36
1.501.501FIGURE 37
1.501.501FIGURE 40
1.501.501FIGURE 41
1.501.501FIGURE 44
1.501.501FIGURE 45
1.501.501FIGURE 48
1.501.501FIGURE 49
3.406.802FIGURE 55
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
43 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 44

Group 2:
Table 6: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
3.406.802FIGURE 56
2.104.202FIGURE 59
2.104.202FIGURE 60
3.003.001FIGURE 63
3.003.001FIGURE 64
1.503.002FIGURE 67
0.750.751FIGURE 68
3.256.502FIGURE 71
0.750.751FIGURE 72
1.001.001Close Access
71.5092.00TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 3:
Table 7: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.002.001FIGURE 2
1.001.001FIGURE 6
1.501.501FIGURE 10
2.505.002FIGURE 14
1.501.501FIGURE 18
2.502.501FIGURE 22
2.502.501FIGURE 26
1.501.501FIGURE 30
1.501.501FIGURE 34
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
44 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 45

Group 3:
Table 7: Chem-Mill Step Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.501.501FIGURE 38
1.501.501FIGURE 42
1.501.501FIGURE 46
2.254.502FIGURE 53
2.752.751FIGURE 57
1.501.501FIGURE 61
2.002.001FIGURE 73
2.002.001FIGURE 77
1.001.001Close Access
33.5038.25TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 3:
Table 8: Modification
Elapsed HoursTask HoursNumber of PersonsTask
13.50108.008Open Access
2.002.001FIGURE 2
8.5017.002FIGURE 3
1.001.001FIGURE 6
4.759.502FIGURE 7
1.501.501FIGURE 10
4.509.002FIGURE 11
2.505.002FIGURE 14
15.0060.004FIGURE 15
1.501.501FIGURE 18
4.5018.004FIGURE 19
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
45 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 46

Group 3:
Table 8: Modification
Elapsed HoursTask HoursNumber of PersonsTask
2.502.501FIGURE 22
9.0036.004FIGURE 23
2.502.501FIGURE 26
9.0036.004FIGURE 27
1.501.501FIGURE 30
9.5038.004FIGURE 31
1.501.501FIGURE 34
4.7519.004FIGURE 35
1.501.501FIGURE 38
4.7519.004FIGURE 39
1.501.501FIGURE 42
4.7519.004FIGURE 43
1.501.501FIGURE 46
4.7519.004FIGURE 47
2.254.502FIGURE 53
14.5087.006FIGURE 54
2.752.751FIGURE 57
13.2553.004FIGURE 58
1.501.501FIGURE 61
9.5038.004FIGURE 62
2.002.001FIGURE 73
17.5070.004FIGURE 74
2.002.001FIGURE 77
17.5070.004FIGURE 78
16.50132.008Close Access
217.50893.75TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)(e)(f)
(a) Estimates do not include time to manufacture parts. Time to manufacture parts is con-
sidered lost time in Boeing estimates.
(b) Totals shown do not include time to test disturbed systems.
(c) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
46 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 47

Group 3:
Table 8: Modification
Elapsed HoursTask HoursNumber of PersonsTask
(d) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(e) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(f) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
Group 3:
Table 9: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Open Access
2.502.501FIGURE 4
0.800.801FIGURE 5
0.750.751FIGURE 8
0.750.751FIGURE 9
1.751.751FIGURE 12
0.750.751FIGURE 13
3.006.002FIGURE 16
1.201.201FIGURE 17
1.501.501FIGURE 20
1.501.501FIGURE 21
3.003.001FIGURE 24
3.003.001FIGURE 25
3.003.001FIGURE 28
3.003.001FIGURE 29
3.003.001FIGURE 32
3.003.001FIGURE 33
1.501.501FIGURE 36
1.501.501FIGURE 37
1.501.501FIGURE 40
1.501.501FIGURE 41
1.501.501FIGURE 44
1.501.501FIGURE 45
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
47 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 48

Group 3:
Table 9: Post Modification Inspections
Elapsed HoursTask HoursNumber of PersonsTask
1.501.501FIGURE 48
1.501.501FIGURE 49
3.406.802FIGURE 55
3.406.802FIGURE 56
2.104.202FIGURE 59
2.104.202FIGURE 60
3.003.001FIGURE 63
3.003.001FIGURE 64
3.256.502FIGURE 75
0.750.751FIGURE 76
3.256.502FIGURE 79
0.750.751FIGURE 80
1.001.001Close Access
71.5092.00TOTAL FOR EACH AIRPLANE (a)(b)(c)(d)
(a) Figures where C-Scan method is an option, factors for C-Scan inspection method were
used in the estimate.
(b) For the optional Medium Frequency Eddy Current (MFEC) Inspection, multiply the esti-
mates given by a factor of 5.
(c) For the optional Magneto Optical Imaging (MOI) Inspection, multiply the estimates given
by a factor of 1.5.
(d) For the optional Ultrasonic Phased Array (UTPA) Inspection, multiply the estimates
given by a factor of 12.
H. Weight and Balance Changes
Group 1:
Change in Moment
(Pound-Inches) (a)
Change in Weight
(Pounds) (a)Location ID (Refer to FIGURE 1)
7002.1EP1
1700.5EP2
3601.0TCAS
1,4503.6ATC
4501.0TACAN
9101.9SAT 1
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
48 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 49

Group 1:
Change in Moment
(Pound-Inches) (a)
Change in Weight
(Pounds) (a)Location ID (Refer to FIGURE 1)
9101.9SAT 2
1,1702.4GPS
5101.0MLS
5701.0ACL
6301.0ELT 1
8601.0ELT 2
3,4505.0ADF 1
2,2002.9ADF 2
1,7502.8OVW 1
1,7502.8OVW 2
(a) As Modifications are accomplished for each applicable airplane, add the Change in
Weight values, and the Change in Moment values for each Modification Location accom-
plished.
Group 2:
Change in Moment
(Pound-Inches) (a)
Change in Weight
(Pounds) (a)Location ID (Refer to FIGURE 1)
7002.1EP1
1700.5EP2
3601.0TCAS
1,4503.6ATC
4501.0TACAN
9101.9SAT 1
9101.9SAT 2
1,1702.4GPS
5101.0MLS
5701.0ACL
6301.0ELT 1
8601.0ELT 2
3,4505.0ADF 1
2,2002.9ADF 2
1,9802.4SAT 3
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
49 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 50

Group 2:
Change in Moment
(Pound-Inches) (a)
Change in Weight
(Pounds) (a)Location ID (Refer to FIGURE 1)
1,7502.8OVW 1
1,7502.8OVW 2
(a) As Modifications are accomplished for each applicable airplane, add the Change in
Weight values, and the Change in Moment values for each Modification Location accom-
plished.
Group 3:
Change in Moment
(Pound-Inches) (a)
Change in Weight
(Pounds) (a)Location ID (Refer to FIGURE 1)
7002.1EP1
1700.5EP2
3601.0TCAS
1,4503.6ATC
4501.0TACAN
9101.9SAT 1
9101.9SAT 2
1,1702.4GPS
5101.0MLS
5701.0ACL
6301.0ELT 1
8601.0ELT 2
3,4505.0ADF 1
2,2002.9ADF 2
1,9802.4SAT 3
1,7502.8OVW 1
1,7502.8OVW 2
(a) As Modifications are accomplished for each applicable airplane, add the Change in
Weight values, and the Change in Moment values for each Modification Location accom-
plished.
I. Electrical Load Data
Not changed.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
50 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 51

J. References
1. Existing Data:
a. Engineering Change Memo PRR 38945, PRR 39800-026RS
b. Boeing Service Letter 737-SL-51-042
c. Boeing Service Related Problem (SRP) 737NG-SRP-53-0370, 737NG-SRP-53-0626
d. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2013-08-08
e. Service Bulletin Index D6-19567
f. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-41-02, 20-43-03, 20-50-19
g. 737 Non-Destructive Testing (NDT) Manual Part 4, 53-30-07, Part 4, 53-30-12, Part 6, 51-00-00,
Part 6, 53-30-00, Part 6, 53-30-09, Part 6, 53-30-18, Part 6, 53-30-19, Part 6, 53-30-23, Part
6, 53-30-25
h. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 25-21-25, 25-21-31, 25-21-45,
25-21-46, 25-21-71, 25-22-00, 25-23-13, 25-23-61, 25-24-10, 25-24-15, 25-24-31, 25-24-77,
25-31-11, 25-31-21, 25-31-31, 25-31-41, 25-31-51, 25-31-71, 25-40-11, 25-40-12, 25-40-13,
25-40-14, 25-40-15, 25-40-16, 25-40-17, 25-40-20, 25-80-00, 51-21-00
i. 737-600 Structural Repair Manual (SRM) 51-10-01, 51-20-01, 51-40-02,51-40-05, 51-40-08
j. Fleet Team Digest (FTD) 737NG-FTD-53-11001, 737NG-FTD-53-20003
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
CROWN PANEL INSTALLATION, SECT 41141A3910
SKIN INSTALLATION - S-4L TO S-4R, STA 360 TO 540143A3110
SKIN INSTALLATION - S-4 TO S-10, STA 360 TO 540143A3130
SKIN INSTALLATION - S-9L TO S-9R, STA 540 TO 727144A3101
SKIN INSTALLATION - S-4L TO S-4R, STA 727 TO 888146A3100
SKIN INSTALLATION - S-4 TO S-10, STA 727 TO 888146A3130
These drawings were used to prepare this Service Bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this Service Bulletin. These drawings may
not be applicable to all airplane configurations or operators.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
51 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 52

K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this Service Bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This Service Bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this Service Bulletin.
L. Interchangeability and Intermixability of Parts
Accomplishment of this Service Bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
52 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 53

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This Service Bulletin
does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are not available for the configuration changes, inspection, and/or modification
procedures given in this Service Bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
Group 1:
NotesNameQTYPart Number /
Specification
(a)(i)2024-T3 CLAD SHEET2 ft X 1 ftQQ-A-250/5, 0.032
inches thick.
(a)(i)2024-T3 CLAD SHEET3 ft X 25 ftQQ-A-250/5, 0.040
inches thick.
(b)(i)2024-T3 CLAD SHEET3 ft X 2 ftQQ-A-250/5, 0.050
inches thick.
(c)(i)PRESSURE AND ENVIRONMEN-
TAL SEALANT
275 ozBMS 5-95, TYPE
1, CLASS B
(c)(i)ORGANIC CORROSION INHIBIT-
ING COMPOUND
220 ozBMS 3-23, TYPE II
(c)(g)(i)PRIMER275 ozBMS 10-11, TYPE
I
(f)(h)(i)CHEMICAL CONVERSION COAT-
ING
275 ozTYPE 2, CLASS A
(d)(e)(i)RIVET1411BACR15BB6D5C
(d)(e)(i)RIVET306BACR15BB6D6C
(d)(e)(i)RIVET108BACR15BB6D7C
(d)(e)(i)RIVET4BACR15BB6D9C
(d)(e)(i)RIVET4BACR15BB6D11C
(d)(e)(i)RIVET401BACR15GF6D5
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
53 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 54

Group 1:
NotesNameQTYPart Number /
Specification
(d)(e)(i)RIVET679BACR15GF6D6
(d)(e)(i)RIVET80BACR15GF6D7
(d)(e)(i)RIVET4BACR15GF6D8
(d)(e)(i)RIVET935BACR15BB6AD5C
(d)(e)(i)RIVET20BACR15BB6AD6C
(d)(e)(i)BOLT11BACB30YP6K3
(d)(e)(i)BOLT52BACB30VT6K7
(d)(e)(i)BOLT48BACB30VT6K8
(d)(e)(i)BOLT4BACB30VT6K9
(e)(i)COLLAR71BACC30BL6
(e)(i)COLLAR16BACC30BQ6
(e)(i)NUT28BACN10ZV3
(a) Make internal doublers and fillers in accordance with the applicable figure for each mod-
ification location.
(b) Make external doublers in accordance with the applicable figure for the overwing modifi-
cation.
(c) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(d) Grip lengths shown are for reference only, fastener length to be determined on installation.
(e) Refer to 737 Structural Repair Manual Chapter 51 for alternate fasteners.
(f) Refer to SOPM 20-43-03 for material sources.
(g) Some primers contain Strontium Chromate and will not be available in the European
Union after January 2019 without an authorization. EU operators are encouraged to ensure
their suppliers are authorized to provide the material after the sunset date and that
downstream users comply with the risk mitigation measures and operational conditions.
(h) Some conversion coatings contain Chromium trioxide/Chromic acid and will not be
available in the European Union after September 2017 without an authorization. EU op-
erators are encouraged to ensure their suppliers are authorized to provide the material
after the sunset date and that downstream users comply with the risk mitigation measures
and operational conditions.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
54 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 55

Group 1:
NotesNameQTYPart Number /
Specification
(i) Can be purchased from The Boeing Company.
Boeing Distribution Services Inc (cage code: 2N935).
3760 W. 108th Street, Miami, FL 33018 USA
Website: https://www.boeingdistribution.com
Telephone: +1.305.925.2600 Fax: +1.305.507.7191 AOG: +1.305.471.8888
Email: Your BDSI customer representative or AOGdesk@Boeingdistribution.com
Group 2:
NotesNameQTYPart Number /
Specification
(a)(i)2024-T3 CLAD SHEET2 ft X 1 ftQQ-A-250/5, 0.032
inches thick.
(a)(i)2024-T3 CLAD SHEET3 ft X 27 ftQQ-A-250/5, 0.040
inches thick.
(b)(i)2024-T3 CLAD SHEET3 ft X 2 ftQQ-A-250/5, 0.050
inches thick.
(c)(i)PRESSURE AND ENVIRONMEN-
TAL SEALANT
280 ozBMS 5-95, TYPE
1, CLASS B
(c)(i)ORGANIC CORROSION INHIBIT-
ING COMPOUND
230 ozBMS 3-23, TYPE II
(c)(g)(i)PRIMER280 ozBMS 10-11, TYPE
I
(f)(h)(i)CHEMICAL CONVERSION COAT-
ING
280 ozTYPE 2, CLASS A
(d)(e)(i)RIVET1515BACR15BB6D5C
(d)(e)(i)RIVET306BACR15BB6D6C
(d)(e)(i)RIVET108BACR15BB6D7C
(d)(e)(i)RIVET4BACR15BB6D9C
(d)(e)(i)RIVET4BACR15BB6D11C
(d)(e)(i)RIVET479BACR15GF6D5
(d)(e)(i)RIVET709BACR15GF6D6
(d)(e)(i)RIVET80BACR15GF6D7
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
55 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 56

Group 2:
NotesNameQTYPart Number /
Specification
(d)(e)(i)RIVET4BACR15GF6D8
(d)(e)(i)RIVET999BACR15BB6AD5C
(d)(e)(i)RIVET20BACR15BB6AD6C
(d)(e)(i)BOLT11BACB30YP6K3
(d)(e)(i)BOLT52BACB30VT6K7
(d)(e)(i)BOLT48BACB30VT6K8
(d)(e)(i)BOLT4BACB30VT6K9
(d)(e)(i)BOLT8BACB30NX6K4
(e)(i)COLLAR71BACC30BL6
(e)(i)COLLAR16BACC30BQ6
(e)(i)COLLAR8BACC30BH6
(e)(i)NUT28BACN10ZV3
(a) Make internal doublers and fillers in accordance with the applicable figure for each mod-
ification location.
(b) Make external doublers in accordance with the applicable figure for the overwing modifi-
cation.
(c) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(d) Grip lengths shown are for reference only, fastener length to be determined on installation.
(e) Refer to 737 Structural Repair Manual Chapter 51 for alternate fasteners.
(f) Refer to SOPM 20-43-03 for material sources.
(g) Some primers contain Strontium Chromate and will not be available in the European
Union after January 2019 without an authorization. EU operators are encouraged to ensure
their suppliers are authorized to provide the material after the sunset date and that
downstream users comply with the risk mitigation measures and operational conditions.
(h) Some conversion coatings contain Chromium trioxide/Chromic acid and will not be
available in the European Union after September 2017 without an authorization. EU op-
erators are encouraged to ensure their suppliers are authorized to provide the material
after the sunset date and that downstream users comply with the risk mitigation measures
and operational conditions.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
56 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 57

Group 2:
NotesNameQTYPart Number /
Specification
(i) Can be purchased from The Boeing Company.
Boeing Distribution Services Inc (cage code: 2N935).
3760 W. 108th Street, Miami, FL 33018 USA
Website: https://www.boeingdistribution.com
Telephone: +1.305.925.2600 Fax: +1.305.507.7191 AOG: +1.305.471.8888
Email: Your BDSI customer representative or AOGdesk@Boeingdistribution.com
Group 3:
NotesNameQTYPart Number /
Specification
(a)(i)2024-T3 CLAD SHEET2 ft X 1 ftQQ-A-250/5, 0.032
inches thick.
(a)(i)2024-T3 CLAD SHEET3 ft X 22 ftQQ-A-250/5, 0.040
inches thick.
(b)(i)2024-T3 CLAD SHEET3 ft X 2 ftQQ-A-250/5, 0.050
inches thick.
(c)(i)PRESSURE AND ENVIRONMEN-
TAL SEALANT
280 ozBMS 5-95, TYPE
1, CLASS B
(c)(i)ORGANIC CORROSION INHIBIT-
ING COMPOUND
230 ozBMS 3-23, TYPE II
(c)(g)(i)PRIMER280 ozBMS 10-11, TYPE
I
(f)(h)(i)CHEMICAL CONVERSION COAT-
ING
280 ozTYPE 2, CLASS A
(d)(e)(i)RIVET1499BACR15BB6D5C
(d)(e)(i)RIVET306BACR15BB6D6C
(d)(e)(i)RIVET108BACR15BB6D7C
(d)(e)(i)RIVET4BACR15BB6D9C
(d)(e)(i)RIVET4BACR15BB6D11C
(d)(e)(i)RIVET481BACR15GF6D5
(d)(e)(i)RIVET707BACR15GF6D6
(d)(e)(i)RIVET80BACR15GF6D7
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
57 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 58

Group 3:
NotesNameQTYPart Number /
Specification
(d)(e)(i)RIVET4BACR15GF6D8
(d)(e)(i)RIVET1001BACR15BB6AD5C
(d)(e)(i)RIVET20BACR15BB6AD6C
(d)(e)(i)BOLT11BACB30YP6K3
(d)(e)(i)BOLT44BACB30VT6K7
(d)(e)(i)BOLT48BACB30VT6K8
(d)(e)(i)BOLT4BACB30VT6K9
(d)(e)(i)BOLT8BACB30NX6K4
(d)(e)(i)COLLAR71BACC30BL6
(e)(i)COLLAR8BACC30BQ6
(e)(i)COLLAR8BACC30BH6
(e)(i)NUT28BACN10ZV3
(a) Make internal doublers and fillers in accordance with the applicable figure for each mod-
ification location.
(b) Make external doublers in accordance with the applicable figure for the overwing modifi-
cation.
(c) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS)
for supplier data.
(d) Grip lengths shown are for reference only, fastener length to be determined on installation.
(e) Refer to 737 Structural Repair Manual Chapter 51 for alternate fasteners.
(f) Refer to SOPM 20-43-03 for material sources.
(g) Some primers contain Strontium Chromate and will not be available in the European
Union after January 2019 without an authorization. EU operators are encouraged to ensure
their suppliers are authorized to provide the material after the sunset date and that
downstream users comply with the risk mitigation measures and operational conditions.
(h) Some conversion coatings contain Chromium trioxide/Chromic acid and will not be
available in the European Union after September 2017 without an authorization. EU op-
erators are encouraged to ensure their suppliers are authorized to provide the material
after the sunset date and that downstream users comply with the risk mitigation measures
and operational conditions.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
58 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 59

Group 3:
NotesNameQTYPart Number /
Specification
(i) Can be purchased from The Boeing Company.
Boeing Distribution Services Inc (cage code: 2N935).
3760 W. 108th Street, Miami, FL 33018 USA
Website: https://www.boeingdistribution.com
Telephone: +1.305.925.2600 Fax: +1.305.507.7191 AOG: +1.305.471.8888
Email: Your BDSI customer representative or AOGdesk@Boeingdistribution.com
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this Service Bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
59 of 388
BOEING SERVICE BULLETIN 737-53-1309

### Page 60

Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1309Revision 1: May 22, 2024
60 of 388
BOEING SERVICE BULLETIN 737-53-1309
BLANK PAGE

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-53-1309/file/77941c78ecf2.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
