# Boeing Service Bulletin 737-53-1310: Revision 1, part 2 of 3

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2025-1367, the docket of a proposed AD (Federal Register 2025-13920). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 737-53-1310](https://openairdocs.org/service-documents/boeing/sb-737-53-1310.md)
- Title as filed: SB-737-53-1310 Rev 1_Part2
- Pages: 147
- PDF: https://openairdocs.org/files/sha256/bb/8b/bb8b076a46b3cd9a0a590443f5074e5cae50c5bc8ad30cd3284a8c74bd609a95
- Page: https://openairdocs.org/service-documents/boeing/sb-737-53-1310/file/bb8b076a46b3

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-7.
STA  STA
500B  500C
S-2R -
S-
-WD
LOOKING INBOARD
'///// INSPECTION AREA
2056231
FIGURE 40: FUSELAGE - SKIN - MLS ANTENNA AREA - CHEM-MILL STEP INSPECTION
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  273 of 510

### Page 2

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the
specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with
one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT
Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager
(MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6,
53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable
substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 40: FUSELAGE - SKIN - MLS ANTENNA AREA - CHEM-MILL STEP INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
274 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 3 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-7.
FILLER C  INTERNAL DOUBLER A  FILLER A  TAPERED FILLER B
7) 8) 15  (4  (6 7 8 15  6) 6) 7) 8) 15)
STA  STA
500B  500C
0.50→
MIN
0.50 →
MIN
TYPICAL
30
S-1
0.50
MIN
0.50
MIN
S-2R
0.50 -→  B
MIN
12 13 14 15  9 12 13 14 15  , 0.50  MIN
FILLER F  INTERNAL DOUBLER B
U 12 13 14 15)
+ EXISTING FASTENER  FILLER D  FWD  TAPERED FILLER E
+ NEW FASTENER
LOOKING OUTBOARD
-- REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION
(SHEET 1 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  275 of 510

### Page 4 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER A
EXISTING
STRINGER
EXISTING
/ SKIN/DOUBLER
INTERNAL
DOUBLER A
A-A
INTERNAL
DOUBLER B
→ EXISTING  SKIN/DOUBLER
EXISTING
STRINGER
FILLER D*
B-B  2051739
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION
(SHEET 2 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  276 of 510

### Page 5

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
NOTE: This figure must be accomplished at the same time as the adjacent modification in FIGURE 37.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--RIVETRemove1
(b)--HOLESInspect2
(c)(g)(h)1-INTERNAL DOUBLER
A
Make3
(d)(g)(h)1-FILLER AMake4
(e)(g)(h)1-TAPERED FILLER BMake5
(f)(g)(h)1-FILLER CMake
To all modification
parts and skin. (i)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply6
To all modification
parts and skin. (j)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts and skin.
(k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply7
See fastener code
table below.
1-FILLER AInstall (New)8
See fastener code
table below.
1-INTERNAL DOUBLER
A
Install (New)
See fastener code
table below.
1-TAPERED FILLER BInstall (New)
See fastener code
table below.
1-FILLER CInstall (New)
(c)(g)(h)1-INTERNAL DOUBLER
B
Make9
(d)(g)(h)1-FILLER DMake10
(e)(g)(h)1-TAPERED FILLER EMake11
(f)(g)(h)1-FILLER FMake
To all modification
parts and skin. (i)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply12
To all modification
parts and skin. (j)
-BMS 10-11, TYPE IPRIMERApply
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
277 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 6

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
To the mating sur-
faces of all modifica-
tion parts. (k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply13
See fastener code
table below.
1-FILLER DInstall (New)14
See fastener code
table below.
1-INTERNAL DOUBLER
B
Install (New)
See fastener code
table below.
1-TAPERED FILLER EInstall (New)
See fastener code
table below.
1-FILLER FInstall (New)
Fillet seal around all
modification parts.
(k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply15
(l)-BMS 3-23, TYPE IIORGANIC CORRO-
SION INHIBITING
COMPOUND
Apply16
(m)--EXTERNAL SURFACEClean17
(n)--EXTERNAL FINISHApply18
(a) Remove fasteners as necessary to get access to the modification area.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of all existing holes for cracking in
accordance with 737 NDT Part 6, 51-00-00, Procedure 16.
(c) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Break
all sharp edges. 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(d) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Make
sure the edge of the filler does not ride into the radius of the chem-mill step. Break all sharp edges. Minimum
125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(e) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches tapered to 0.010 inches. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(f) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches. Break all sharp edges. Minimum
125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(g) Maintain a minimum of 2D edge margin at all fastener locations. Maintain a 4D to 6D spacing between
rows of fasteners. Follow stringer pattern for spacing of fasteners forward and aft. Make sure the number
of fasteners and locations are kept as shown. Make sure that the modification parts or fasteners do not
ride the radius of the chem-mill pockets. Make sure the last fastener forward and aft on the filler in the
chem-mill pocket has a minimum of 0.50 inch edge margin to the edge of the chem-mill step.
(h) Make sure there are no nicks, scratches, burrs or sharp edges on the modification parts or the skin.
(i) Apply to bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted procedure.
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
278 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 7

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(j) Apply to chemical conversion coated surfaces. Refer to SOPM 20-41-02 as an accepted procedure.
(k) Refer to SOPM 20-50-19 as an accepted procedure.
(l) Apply to all internal modification parts and surrounding skin and structure. Refer to 737-700 SRM 51-20-
01 or 737-700IGW (BBJ) SRM 51-20-01 as an accepted procedure.
(m) Clean the external surface where an external finish will be applied. Refer to SOPM 20-30-03 as an accepted
procedure.
(n) Apply as necessary to the external surface of the modification area to match the adjacent structure. Refer
to 737-600/700/800/900 AMM 51-21-00 as an accepted procedure.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
(a)(b)0.190 - 0.19644BACR15BB6D5CRIVETA
(a)(b)0.190 - 0.19622BACR15GF6D5RIVETB
(a)(b)0.190 - 0.19636BACR15GF6D6RIVET
(a)(b)0.190 - 0.19630BACR15BB6AD5CRIVETC
(a) Fastener length to be determined on installation. Grip lengths shown are for reference only.
(b) Overdrive rivets in accordance with 737-700 SRM 51-40-02 or 737-700IGW (BBJ) SRM 51-40-02.
FIGURE 41: FUSELAGE - SKIN - MLS ANTENNA AREA - INTERNAL MODIFICATION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
279 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 8 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-7.
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FILLER
STA  STA
500C  500B
S-
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FWD  FILLER
INSPECTION AREA
LOOKING INBOARD  2060442
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 42: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  280 of 510

### Page 9

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--SKINInspect1
(a) Do an external detailed inspection for cracking between fasteners within the indicated area or do an ex-
ternal High Frequency Eddy Current (HFEC) inspection for cracking between fasteners within the indicated
area in accordance with 737 NDT Part 6, 51-00-00 Procedure 23.
FIGURE 42: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT OUTER
FASTENER ROWS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
281 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 10 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-7.
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FILLER
STA  STA
500C  500B
+
→
S-2R
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FWD  FILLER
NDI INSPECTION AREA  LOOKING INBOARD  2060444
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 43: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM-MILL
STEP
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  282 of 510

### Page 11

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(b)--SKINInspect1
(a) Do an external Non Destructive Inspection (NDI) for cracking in the chem-milled step in accordance with
737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18. NOTE: Frequency adjustment on the airplane
should be done at an area not common to the internal filler. A "U" shape signal at the chem-milled edge
per 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 may not be found in the area common to the
filler/doubler but is satisfactory.
(b) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
FIGURE 43: FUSELAGE - SKIN - MLS ANTENNA AREA - POST MODIFICATION INSPECTION AT CHEM-MILL
STEP
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
283 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 12 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-3, 5.
STA  STA
559  578
АНАЇНАНААНАННАНA!
- S-2R
‡H+  tH+tH.  - S-1
FWD
LOOKING INBOARD
/ INSPECTION AREA
2056232
FIGURE 44: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - CHEM-MILL STEP
INSPECTION
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  284 of 510

### Page 13

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the
specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with
one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT
Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager
(MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6,
53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable
substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 44: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - CHEM-MILL STEP
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
285 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 14 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-3, 5.
TAPERED FILLER B  FILLER A  INTERNAL DOUBLER A  TAPERED FILLER C
501 8 15  30181  501815
STA  STA
559  578
0.50  0.50
MIN  0.50  MIN
MIN
+ +5  TYPICAL
+ 4%
30 °
+ 45
- S-1
18)
+
СІБ  + 80  - S-2R
+
+ 5
0.50 -  MIN  0.50  MIN  B -  - 0.50  MIN
U 12 13 14 15  10 12 13 14 15  9 12 13 14 15)  1 12 13 14 15
TAPERED FILLER E  FILLER D  INTERNAL DOUBLER B  TAPERED FILLER F
* EXISTING FASTENER  •WD
+ NEW FASTENER  LOOKING OUTBOARD
*- REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 45: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION
(SHEET 1 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  286 of 510

### Page 15 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLERA
EXISTING
STRINGER ~
INTERNAL
DOUBLER A
EXISTING
SKIN/DOUBLER
A-A
EXISTING
SKIN/DOUBLER
INTERNAL
DOUBLER B
EXISTING -
STRINGER
FILLERD
B-B  2051741
FIGURE 45: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION
(SHEET 2 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
BOEING PROPRIETARY - See page 1 for details  Export Controlled ECCN: 9E991  287 of 510

### Page 16

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--RIVETRemove1
(b)--HOLESInspect2
(c)(f)(g)1-INTERNAL DOUBLER
A
Make3
(d)(f)(g)1-FILLER AMake4
(e)(f)(g)1-TAPERED FILLER BMake5
(e)(f)(g)1-TAPERED FILLER CMake
To all modification
parts and skin. (h)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply6
To all modification
parts and skin. (i)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply7
See fastener code
table below.
1-FILLER AInstall (New)8
See fastener code
table below.
1-INTERNAL DOUBLER
A
Install (New)
See fastener code
table below.
1-TAPERED FILLER BInstall (New)
See fastener code
table below.
1-TAPERED FILLER CInstall (New)
(c)(f)(g)1-INTERNAL DOUBLER
B
Make9
(d)(f)(g)1-FILLER DMake10
(e)(f)(g)1-TAPERED FILLER EMake11
(e)(f)(g)1-TAPERED FILLER FMake
To all modification
parts and skin. (h)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply12
To all modification
parts and skin. (i)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply13
FIGURE 45: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
288 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 17

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
See fastener code
table below.
1-FILLER DInstall (New)14
See fastener code
table below.
1-INTERNAL DOUBLER
B
Install (New)
See fastener code
table below.
1-TAPERED FILLER EInstall (New)
See fastener code
table below.
1-TAPERED FILLER FInstall (New)
Fillet seal around all
modification parts. (j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply15
(k)-BMS 3-23, TYPE IIORGANIC CORRO-
SION INHIBITING
COMPOUND
Apply16
(l)--EXTERNAL SURFACEClean17
(m)--EXTERNAL FINISHApply18
(a) Remove fasteners as necessary to get access to the modification area.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of all existing holes for cracking in
accordance with 737 NDT Part 6, 51-00-00, Procedure 16.
(c) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(d) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Make
sure the edge of the filler does not ride into the radius of the chem-mill step. Break all sharp edges. Minimum
125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(e) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches tapered to 0.010 inches. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(f) Maintain a minimum of 2D edge margin at all fastener locations. Maintain a 4D to 6D spacing between
rows of fasteners. Follow stringer pattern for spacing of fasteners forward and aft. Make sure the number
of fasteners and locations are kept as shown. Make sure that the modification parts or fasteners do not
ride the radius of the chem-mill pockets. Make sure the last fastener forward and aft on the filler in the
chem-mill pocket has a minimum of 0.50 inch edge margin to the edge of the chem-mill step. Make sure
the fasteners outside the chem-mill pocket have a minimum of 2D edge margin from the edge of the chem-
mill step.
(g) Make sure there are no nicks, scratches, burrs or sharp edges on the modification parts or the skin.
(h) Apply to bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted procedure.
(i) Apply to chemical conversion coated surfaces. Refer to SOPM 20-41-02 as an accepted procedure.
(j) Refer to SOPM 20-50-19 as an accepted procedure.
FIGURE 45: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
289 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 18

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(k) Apply to all internal modification parts and surrounding skin and structure. Refer to 737-700 SRM 51-20-
01 as an accepted procedure.
(l) Clean the external surface where an external finish will be applied. Refer to SOPM 20-30-03 as an accepted
procedure.
(m) Apply as necessary to the external surface of the modification area to match the adjacent structure. Refer
to 737-600/700/800/900 AMM 51-21-00 as an accepted procedure.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
(a)(b)0.190 - 0.19644BACR15BB6D5CRIVETA
(a)(b)0.190 - 0.19622BACR15GF6D5RIVETB
(a)(b)0.190 - 0.19630BACR15GF6D6RIVET
(a)(b)0.190 - 0.19630BACR15BB6AD5CRIVETC
(a) Fastener length to be determined on installation. Grip lengths shown are for reference only.
(b) Overdrive rivets in accordance with 737-700 SRM 51-40-02.
FIGURE 45: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - INTERNAL
MODIFICATION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
290 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 19 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-3, 5.
TAPERED FILLER  INTERNAL DOUBLER  FILLER  TAPERED FILLER
STA  STA
578  559
HI X
S-1
S-2R
FWD
TAPERED FILLER  INTERNAL DOUBLER  FILLER  TAPERED FILLER
INSPECTION AREA
LOOKING INBOARD  2060447
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 46: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  291 of 510

### Page 20

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--SKINInspect1
(a) Do an external detailed inspection for cracking between fasteners within the indicated area or do an ex-
ternal High Frequency Eddy Current (HFEC) inspection for cracking between fasteners within the indicated
area in accordance with 737 NDT Part 6, 51-00-00 Procedure 23.
FIGURE 46: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
292 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 21 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-3, 5.
TAPERED FILLER  INTERNAL DOUBLER  FILLER  TAPERED FILLER
STA  STA
578  559
S-1
S-2R •
FWD
TAPERED FILLER  INTERNAL DOUBLER  FILLER  TAPERED FILLER
NDI INSPECTION AREA  LOOKING INBOARD  2060451
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 47: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  293 of 510

### Page 22

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(b)--SKINInspect1
(a) Do an external Non Destructive Inspection (NDI) for cracking in the chem-milled step in accordance with
737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18. NOTE: Frequency adjustment on the airplane
should be done at an area not common to the internal filler. A "U" shape signal at the chem-milled edge
per 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 may not be found in the area common to the
filler/doubler but is satisfactory.
(b) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
FIGURE 47: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (PRE-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
294 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 23 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 4.
STA  STA  STA
540  559  597
• S-2R
• S-1
FWD
LOOKING INBOARD
''/////, INSPECTION AREA
3048747
FIGURE 48: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - CHEM-MILL STEP
INSPECTION
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  295 of 510

### Page 24

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the
specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with
one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT
Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager
(MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6,
53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the horizontal chem-mill step within the NDI area as specified in AP-
PENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable
substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 48: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - CHEM-MILL STEP
INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
296 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 25 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 4.
B
STA  STA
540  559
S-2R
FWD
LOOKING OUTBOARI
STRINGERS NOT SHOWN FOR CLARITY
2052443
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 1 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  BOEING PROPRIETARY - See page 1 for details  Export Controlled ECCN: 9E991  737-53-1310  297 of 510

### Page 26 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
TAPERED FILLER C  INTERNAL DOUBLER A  FILLER A  FILLER B
(25  Y25)
STA  STA
540  559
0.50  • 0.50
MIN  MIN
TYPICAL
30
Ete Ste  - S-1
A-
els
3te 3t6  t6 to ete ate te  - S-2R
30
TYPICAL
0.50  B  0.50
MIN  MIN
018 125  7 8 10  618 0 25
TAPERED FILLER F  INTERNAL DOUBLER B  4 1 8 1 25  FILLER E
* EXISTING FASTENER  FILLER D
- NEW FASTENER  LOOKING OUTBOARD  FWD  2052460
- REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 2 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  298 of 510

### Page 27 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER G  INTERNAL DOUBLER C  FILLER H
(12) 14)15  25  (11) 14)  13 14 15  16) 25
STA  STA
559  578
0.50  _ 0.50
MIN  MIN
+ 15
CTE  - S-1
ČIs  +  ets
0.50
MIN
0.50
MIN
+
36 at 8t6 ot6 816  S-2R
*†5
0.50  - 0.50
MIN  MIN
12  13 14 15 1 25
FILLER I  INTERNAL DOUBLER D  FILLER J
* EXISTING FASTENER
+ NEW FASTENER  LOOKING OUTBOARD  2052764
-*- REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 3 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  299 of 510

### Page 28 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER K  INTERNAL DOUBLER E  FILLER L  TAPERED FILLER M
18  (25)  (23 25)
STA  STA
578  597
0.50  MIN  E  →  • 0.50  MIN
TYPICAL  Sto AS  - %5
30°1
- %5
oto ote ti  • S-1
+
T
0.50  0.50
MIN  MIN
0.50 -  • 0.50
MIN  MIN
- 0.50
MIN
0.50
MIN
— S-2R
+
• T  - 15
0.50  0.50 →
MIN  MIN
(26)27)28
19 21 22 24 25  18 21 22 24 25  9 21 22 24 25  20 21 22 20 25
FILLER N  INTERNAL DOUBLER F  FILLER O  TAPERED FILLER P
FWD
+ EXISTING FASTENER  C
+ NEW FASTENER  LOOKING OUTBOARD  2052765
-*- REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 4 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  300 of 510

### Page 29 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER A .
DOUBLER B -  INTERNAL  EXISTING  SKIN/DOUBLER
EXISTING
STRINGER
EXISTING
STRINGER
INTERNAL  DOUBLER A  EXISTING  SKIN/DOUBLER
FILLER D
A-A  B-B
FILLER G  INTERNAL  SKIN/DOUBLER  , EXISTING
DOUBLER D
EXISTING
STRINGER
EXISTING
STRINGER
EXISTING
INTERNAL  SKIN/DOUBLER
DOUBLER C
FILLER I
C-C  D-D
FILLER K  FILLER O-
EXISTING  EXISTING
STRINGER  STRINGER
INTERNAL
INTERNAL  DOUBLER F  EXISTING
DOUBLER E  SKIN
FILLER L  EXISTING  SKIN  FILLER N  2052795
E-E  F-F
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 5 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  301 of 510

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--RIVETRemove1
(b)--HOLESInspect2
(c)(g)(h)1-INTERNAL DOUBLER
A
Make3
(c)(g)(h)1-INTERNAL DOUBLER
B
Make
(d)(g)(h)1-FILLER AMake4
(d)(g)(h)1-FILLER DMake
(e)(g)(h)1-FILLER BMake5
(e)(g)(h)1-FILLER EMake
(f)(g)(h)1-TAPERED FILLER CMake6
(f)(g)(h)1-TAPERED FILLER FMake
To all modification
parts and skin. (i)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply7
To all modification
parts and skin. (j)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply8
See fastener code
table below.
1-FILLER AInstall (New)9
See fastener code
table below.
1-FILLER BInstall (New)
See fastener code
table below.
1-INTERNAL DOUBLER
A
Install (New)
See fastener code
table below.
1-TAPERED FILLER CInstall (New)
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 6 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
302 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 31

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
See fastener code
table below.
1-FILLER DInstall (New)10
See fastener code
table below.
1-FILLER EInstall (New)
See fastener code
table below.
1-INTERNAL DOUBLER
B
Install (New)
See fastener code
table below.
1-TAPERED FILLER FInstall (New)
(c)(g)(h)1-INTERNAL DOUBLER
C
Make11
(c)(g)(h)1-INTERNAL DOUBLER
D
Make
(d)(g)(h)1-FILLER GMake12
(d)(g)(h)1-FILLER IMake
(e)(g)(h)1-FILLER HMake13
(e)(g)(h)1-FILLER JMake
To all modification
parts and skin. (i)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply14
To all modification
parts and skin. (j)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply15
See fastener code
table below.
1-FILLER GInstall (New)16
See fastener code
table below.
1-INTERNAL DOUBLER
C
Install (New)
See fastener code
table below.
1-FILLER HInstall (New)
See fastener code
table below.
1-FILLER IInstall (New)17
See fastener code
table below.
1-INTERNAL DOUBLER
D
Install (New)
See fastener code
table below.
1-FILLER JInstall (New)
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 7 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
303 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 32

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(c)(g)(h)1-INTERNAL DOUBLER
E
Make18
(c)(g)(h)1-INTERNAL DOUBLER
F
Make
(d)(g)(h)1-FILLER KMake19
(d)(g)(h)1-FILLER NMake
(d)(g)(h)1-FILLER LMake
(d)(g)(h)1-FILLER OMake
(f)(g)(h)1-TAPERED FILLER MMake20
(f)(g)(h)1-TAPERED FILLER PMake
To all modification
parts and skin. (i)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply21
To all modification
parts and skin. (j)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply22
See fastener code
table below.
1-FILLER KInstall (New)23
See fastener code
table below.
1-FILLER LInstall (New)
See fastener code
table below.
1-INTERNAL DOUBLER
E
Install (New)
See fastener code
table below.
1-TAPERED FILLER MInstall (New)
See fastener code
table below.
1-FILLER NInstall (New)24
See fastener code
table below.
1-FILLER OInstall (New)
See fastener code
table below.
1-INTERNAL DOUBLER
F
Install (New)
See fastener code
table below.
1-TAPERED FILLER PInstall (New)
Fillet seal around all
modification parts.
(k)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply25
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 8 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
304 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 33

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(l)-BMS 3-23, TYPE IIORGANIC CORRO-
SION INHIBITING
COMPOUND
Apply26
(m)--EXTERNAL SURFACEClean27
(n)--EXTERNAL FINISHApply28
(a) Remove fasteners as necessary to get access to the modification area.
(b) Do open hole High Frequency Eddy Current (HFEC) inspection of all existing holes for cracking in accor-
dance with 737 NDT Part 6, 51-00-00, Procedure 16.
(c) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(d) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Make
sure the edge of the filler does not ride into the radius of the chem-mill step. Break all sharp edges. Minimum
125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(e) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches. Break all sharp edges. Minimum
125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(f) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches tapered to 0.010 inches. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(g) Maintain a minimum of 2D edge margin at all fastener locations. Maintain a 4D to 6D spacing between
rows of fasteners. Follow stringer pattern for spacing of fasteners forward and aft. Make sure the number
of fasteners and locations are kept as shown. Make sure that the modification parts or fasteners do not
ride the radius of the chem-mill pockets. Make sure the last fastener forward and aft on the filler in the
chem-mill pocket has a minimum of 0.50 inch edge margin to the edge of the chem-mill step. Make sure
the fasteners outside the chem-mill pocket have a minimum of 2D edge margin from the edge of the chem-
mill step.
(h) Make sure there are no nicks, scratches, burrs or sharp edges on the modification parts or the skin.
(i) Apply to bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted procedure.
(j) Apply to chemical conversion coated surfaces. Refer to SOPM 20-41-02 as an accepted procedure.
(k) Refer to SOPM 20-50-19 as an accepted procedure.
(l) Apply to all internal modification parts and surrounding skin and structure. Refer to 737-700 SRM 51-20-
01 as an accepted procedure.
(m) Clean the external surface where an external finish will be applied. Refer to SOPM 20-30-03 as an accepted
procedure.
(n) Apply as necessary to the external surface of the modification area to match the adjacent structure. Refer
to 737-600/700/800/900 AMM 51-21-00 as an accepted procedure.
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 9 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
305 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 34

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
(a)(b)0.190 - 0.196140BACR15BB6D5CRIVETA
(a)(b)0.190 - 0.19650BACR15GF6D5RIVETB
(a)(b)0.190 - 0.19684BACR15GF6D6RIVET
(a)(b)0.190 - 0.19698BACR15BB6AD5CRIVETC
(a) Fastener length to be determined on installation. Grip lengths shown are for reference only.
(b) Overdrive rivets in accordance with 737-700 SRM 51-40-02.
FIGURE 49: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - INTERNAL
MODIFICATION
(SHEET 10 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
306 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 35 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 4.
STA  STA  STA
597  559  540
S-2R-
FWD
LOOKING INBOARD
STRINGERS NOT SHOWN FOR CLARIT\
2060452
FIGURE 50: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 1 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  307 of 510

### Page 36 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FILLER
STA  STA
597  578
S-1
S-2R
FWD
TAPERED FILLER  FILLER  INTERNAL DOUBLER FILLER
INSPECTION AREA  LOOKING INBOARD  2060456
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 50: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 2 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  308 of 510

### Page 37 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER  INTERNAL DOUBLER  FILLER
STA  STA
578  559
S-1
i+ +
S-2R -
FWD
FILLER  INTERNAL DOUBLER  FILLER
INSPECTION AREA  STRINGERS NOT SHOWN FOR CLARITY  LOOKING INBOARD  2060454
FIGURE 50: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 3 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  309 of 510

### Page 38 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
STA  STA
559  540
S-1
TJ
S-2R -
FILLER  FWD  INTERNAL DOUBLER  TAPERED FILLER
FILLER
INSPECTION AREA  LOOKING INBOARD  2060453
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 50: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 4 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  310 of 510

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--SKINInspect1
(a) Do an external detailed inspection for cracking between fasteners within the indicated area or do an ex-
ternal High Frequency Eddy Current (HFEC) inspection for cracking between fasteners within the indicated
area in accordance with 737 NDT Part 6, 51-00-00 Procedure 23.
FIGURE 50: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT OUTER FASTENER ROWS
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
311 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 40 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 4.
STA  STA  STA  STA
597  578  559  540
S-1
- S-2R
FWD
LOOKING INBOARD
STRINGERS NOT SHOWN FOR CLARITY
2060043
FIGURE 51: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 1 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  312 of 510

### Page 41 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FILLER
STA  STA
597  578
IL  - S-1
- S-2R
TAPERED FILLER  FILLER  INTERNAL DOUBLER  FILLER
FWD
/ NDI INSPECTION AREA  2060057
LOOKING INBOARD
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 51: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 2 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  313 of 510

### Page 42 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER  INTERNAL DOUBLER  FILLER
STA  STA
578  559
ı]  - S-1
— S-2R
FILLER  INTERNAL DOUBLER  FILLER
FWD
NDI INSPECTION AREA
B
LOOKING INBOARD  2060056
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 51: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 3 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  314 of 510

### Page 43 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
STA  STA
559  540
- S-1
— S-2R
FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
NDI INSPECTION AREA  FWD
LOOKING INBOARD  2060046
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 51: FUSELAGE - SKIN- ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 4 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  315 of 510

### Page 44

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(b)--SKINInspect1
(a) Do an external Non Destructive Inspection (NDI) for cracking in the chem-milled step in accordance with
737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18. NOTE: Frequency adjustment on the airplane
should be done at an area not common to the internal filler. A "U" shape signal at the chem-milled edge
per 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 may not be found in the area common to the
filler/doubler but is satisfactory.
(b) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
FIGURE 51: FUSELAGE - SKIN - ANTI-COLLISION LIGHT AREA (POST-PRR38745) - POST MODIFICATION
INSPECTION AT CHEM-MILL STEP
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
316 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 45 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-5.
STA  STA
616  639
— S-2R
FWD
LOOKING INBOARD
'////, INSPECTION AREA
2056234
FIGURE 52: FUSELAGE - SKIN - ELT ANTENNA AREA - CHEM-MILL STEP INSPECTION
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
BOEING PROPRIETARY - See page 1 for details  Export Controlled ECCN: 9E991  317 of 510

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the
specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with
one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT
Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager
(MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6,
53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable
substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 52: FUSELAGE - SKIN - ELT ANTENNA AREA - CHEM-MILL STEP INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
318 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 47 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-5.
INTERNAL DOUBLER A  FILLER A
ЗX6Х  Y15)
TAPERED FILLER C  TAPERED FILLER B
15  Đ010T
STA  STA
616  639
MIN  0.50  А  MIN  0.50
TYPICAL  +  + + % 9
30 °
• S-1
els
0.50
MIN
0.50
MIN
+
- S-2R
75
+ +5
0.50  0.50
MIN  MIN
11) 12) 13 14 15)
TAPERED FILLER F  1 12 13 14 15
TAPERED FILLER E
INTERNAL DOUBLER B  10
+ EXISTING FASTENER  FILLER D
NEW FASTENER  LOOKING OUTBOARD
REFERENCE FASTENER  STRINGERS NOT SHOWN FOR CLARITY
FIGURE 53: FUSELAGE - SKIN - ELT ANTENNA LOCATION - INTERNAL MODIFICATIONI
(SHEET 1 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  319 of 510

### Page 48 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
FILLER A
EXISTING
STRINGER -
INTERNAL
DOUBLER A
→ EXISTING  SKIN/DOUBLER
A-A
- SKIN/DOUBLER  EXISTING
INTERNAL
DOUBLER B
EXISTING
STRINGER
FILLER D
B-B  2051742
FIGURE 53: FUSELAGE - SKIN - ELT ANTENNA LOCATION - INTERNAL MODIFICATION
(SHEET 2 OF 5)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  320 of 510

### Page 49

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--RIVETRemove1
(b)--HOLESInspect2
(c)(f)(g)1-INTERNAL DOUBLER
A
Make3
(d)(f)(g)1-FILLER AMake4
(e)(f)(g)1-TAPERED FILLER BMake5
(e)(f)(g)1-TAPERED FILLER CMake
To all modification
parts and skin. (h)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply6
To all modification
parts and skin. (i)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts and skin.
(j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply7
See fastener code
table below.
1-FILLER AInstall (New)8
See fastener code
table below.
1-INTERNAL DOUBLER
A
Install (New)
See fastener code
table below.
1-TAPERED FILLER BInstall (New)
See fastener code
table below.
1-TAPERED FILLER CInstall (New)
(c)(f)(g)1-INTERNAL DOUBLER
B
Make9
(d)(f)(g)1-FILLER DMake10
(e)(f)(g)1-TAPERED FILLER EMake11
(e)(f)(g)1-TAPERED FILLER FMake
To all modification
parts and skin. (h)
-TYPE 2, CLASS ACHEMICAL CONVER-
SION COATING
Apply12
To all modification
parts and skin. (i)
-BMS 10-11, TYPE IPRIMERApply
To the mating sur-
faces of all modifica-
tion parts. (j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply13
FIGURE 53: FUSELAGE - SKIN - ELT ANTENNA LOCATION - INTERNAL MODIFICATION
(SHEET 3 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
321 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 50

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
See fastener code
table below.
1-FILLER DInstall (New)14
See fastener code
table below.
1-INTERNAL DOUBLER
B
Install (New)
See fastener code
table below.
1-TAPERED FILLER EInstall (New)
See fastener code
table below.
1-TAPERED FILLER FInstall (New)
Fillet seal around all
modification parts. (j)
-BMS 5-95, TYPE 1,
CLASS B
PRESSURE AND ENVI-
RONMENTAL
SEALANT
Apply15
(k)-BMS 3-23, TYPE IIORGANIC CORRO-
SION INHIBITING
COMPOUND
Apply16
(l)--EXTERNAL SURFACEClean17
(m)--EXTERNAL FINISHApply18
(a) Remove fasteners as necessary to get access to the modification area.
(b) Do an open hole High Frequency Eddy Current (HFEC) inspection of all existing holes for cracking in
accordance with 737 NDT Part 6, 51-00-00, Procedure 16.
(c) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(d) Make from 2024-T3 clad sheet / QQ-A-250/5, 0.040 inches thick. 0.50 inches radius on the corners. Follow
the edge of the chem-mill pocket when trimming the edge of the filler facing the stringer. Make sure the
edge of the filler does not ride into the radius of the chem-mill step. Break all sharp edges. Minimum 125
Ra surface finish. Refer to the fastener code table below for hole sizes.
(e) Make from 2024-T3 clad sheet / QQ-A-250/5, stock thickness 0.040 inches tapered to 0.010 inches. Break
all sharp edges. Minimum 125 Ra surface finish. Refer to the fastener code table below for hole sizes.
(f) Maintain a minimum of 2D edge margin at all fastener locations. Maintain a 4D to 6D spacing between
rows of fasteners. Follow stringer pattern for spacing of fasteners forward and aft. Make sure the number
of fasteners and locations are kept as shown. Make sure that the modification parts or fasteners do not
ride the radius of the chem-mill pockets. Make sure the last fastener forward and aft on the filler in the
chem-mill pocket has a minimum of 0.50 inch edge margin to the edge of the chem-mill step.
(g) Make sure there are no nicks, scratches, burrs or sharp edges on the modification parts or the skin.
(h) Apply to bare aluminum surfaces. Refer to SOPM 20-43-03 as an accepted procedure.
(i) Apply to chemical conversion coated surfaces. Refer to SOPM 20-41-02 as an accepted procedure.
(j) Refer to SOPM 20-50-19 as an accepted procedure.
(k) Apply to all internal modification parts and surrounding skin and structure. Refer to 737-700 SRM 51-20-
01 as an accepted procedure.
FIGURE 53: FUSELAGE - SKIN - ELT ANTENNA LOCATION - INTERNAL MODIFICATION
(SHEET 4 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
322 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 51

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(l) Clean the external surface where an external finish will be applied. Refer to SOPM 20-30-03 as an accepted
procedure.
(m) Apply as necessary to the external surface of the modification area to match the adjacent structure. Refer
to 737-600/700/800/900 AMM 51-21-00 as an accepted procedure.
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener. The QTY numbers shown below are the
number of fasteners necessary for this figure.
MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
(a)(b)0.190 - 0.19652BACR15BB6D5CRIVETA
(a)(b)0.190 - 0.19626BACR15GF6D5RIVETB
(a)(b)0.190 - 0.19634BACR15GF6D6RIVET
(a)(b)0.190 - 0.19634BACR15BB6AD5CRIVETC
(a) Fastener length to be determined on installation. Grip lengths shown are for reference only.
(b) Overdrive rivets in accordance with 737-700 SRM 51-40-02.
FIGURE 53: FUSELAGE - SKIN - ELT ANTENNA LOCATION - INTERNAL MODIFICATION
(SHEET 5 OF 5)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
323 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-5.
TAPERED FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
STA  1)  STA
639  616
+
- S-1
- S-2R
TAPERED FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
INSPECTION AREA  FWD
LOOKING INBOARD  2060058
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 54: FUSELAGE - SKIN - ELT ANTENNA LOCATION - POST MODIFICATION INSPECTION AT
OUTER FASTENER ROWS
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  324 of 510

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--SKINInspect1
(a) Do an external detailed inspection for cracking between fasteners within the indicated area or do an ex-
ternal High Frequency Eddy Current (HFEC) inspection for cracking between fasteners within the indicated
area in accordance with 737 NDT Part 6, 51-00-00 Procedure 23.
FIGURE 54: FUSELAGE - SKIN - ELT ANTENNA LOCATION - POST MODIFICATION INSPECTION AT
OUTER FASTENER ROWS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
325 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 54 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-5.
TAPERED FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
STA  STA
639  616
_It+
+ + 7+
• S-1
+
- S-2R
TAPERED FILLER  FILLER  INTERNAL DOUBLER  TAPERED FILLER
NDI INSPECTION AREA  FWD
LOOKING INBOARD  2060072
STRINGERS NOT SHOWN FOR CLARITY
FIGURE 55: FUSELAGE - SKIN - ELT ANTENNA LOCATION - POST MODIFICATION INSPECTION AT
CHEM-MILL STEP
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  326 of 510

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(b)--SKINInspect1
(a) Do an external Non Destructive Inspection (NDI) for cracking in the chem-milled step in accordance with
737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18. NOTE: Frequency adjustment on the airplane
should be done at an area not common to the internal filler. A "U" shape signal at the chem-milled edge
per 737 NDT Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 may not be found in the area common to the
filler/doubler but is satisfactory.
(b) Inspections are only required along the horizontal chem-mill step within the NDI inspection area in accor-
dance with APPENDIX A.
FIGURE 55: FUSELAGE - SKIN - ELT ANTENNA LOCATION - POST MODIFICATION INSPECTION AT
CHEM-MILL STEP
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
327 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 56 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-2, 5.
STA  663.75
FWD  LOOKING INBOARD
INSPECTION AREA
2055613
FIGURE 56: FUSELAGE - SKIN - OVERWING EXIT DOUBLER (PRE PRR 38432) - LEFT SIDE - CHEM-MILL
STEP INSPECTION
(SHEET 1 OF 2)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  328 of 510

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)--SKINInspect1
(b)(c)(d)--SKINInspect2
(a) Do an external detailed inspection for cracking in the fuselage skin along the chem-mill steps at the
specified locations.
(b) Do an external Non Destructive Inspection (NDI) for cracking at the chem-mill step in accordance with
one of the following methods: (1) Medium Frequency Eddy Current (MFEC) in accordance with 737 NDT
Part 6, 53-30-09 or 737 NDT Part 6, 53-30-18 or 737 NDT Part 6, 53-30-23 or (2) Magneto Optic Imager
(MOI) in accordance with 737 NDT Part 6, 53-30-19 or (3) C-Scan in accordance with 737 NDT Part 6,
53-30-25 or (4) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Part 4, 53-30-07.
(c) Inspections are only required along the chem-mill step within the NDI inspection area in accordance with
APPENDIX A.
(d) Ultrasonic Phased Array (UTPA) in accordance with 737 NDT Manual Part 4, 53-30-12 is an acceptable
substitute for 737 NDT Manual Part 4, 53-30-07.
FIGURE 56: FUSELAGE - SKIN - OVERWING EXIT DOUBLER (PRE PRR 38432) - LEFT SIDE - CHEM-MILL
STEP INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: October 20, 2011
737-53-1310Revision 1 May 22, 2024
329 of 510
BOEING SERVICE BULLETIN 737-53-1310

### Page 58 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
This Figure applies only to: Group 1-2, 5.
- 00
FWD  LOOKING OUTBOARD  STRINGERS NOT SHOWN FOR CLARITY
<N
2058773
FIGURE 57: FUSELAGE - SKIN - OVERWING EXIT DOUBLER (PRE PRR 38432) - LEFT SIDE - INTERNAL
AND EXTERNAL MODIFICATION
(SHEET 1 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  330 of 510

### Page 59 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
INTERNAL DOUBLER A  FILLER A
301  8 16)  4013G
STA  STA
597  TEAR  STRAP  578
- S-8L
0.50
MIN
TYPICAL
0.50
_TYPICAL  MIN
%5
СІБ  СТБ  • S-9L
els
95
95
• 0.50  - 0.50
MIN  MIN
5\6)  7 8 16  (4)6)  (16  € 1 8 16
TAPERED FILLER D  FILLER B  TAPERED FILLER C
FWD
• EXISTING FASTENER
+ NEW FASTENER
*- REFERENCE FASTENER
LOOKING OUTBOARD
STRINGERS NOT SHOWN FOR CLARITY  2058774
FIGURE 57: FUSELAGE - SKIN - OVERWING EXIT DOUBLER (PRE PRR 38432) - LEFT SIDE - INTERNAL
AND EXTERNAL MODIFICATION
(SHEET 2 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  Export Controlled ECCN: 9E991  737-53-1310
BOEING PROPRIETARY - See page 1 for details  331 of 510

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-53-1310
TEAR STRAP  EXTERNAL DOUBLER A
(16  15 16)
STA  STA
597  D11  616
- S-8L
45/A76/97  +  AXIATI  BAT BAT
- S-9L
+ 76
4% 6 1*  — 6
6 7 17A
FWD
* EXISTING FASTENER
+ NEW FASTENER
LOOKING INBOARD
2058469
FIGURE 57: FUSELAGE - SKIN - OVERWING EXIT DOUBLER (PRE PRR 38432) - LEFT SIDE - INTERNAL
AND EXTERNAL MODIFICATION
(SHEET 3 OF 10)
Original Issue: October 20, 2011
Revision 1 May 22, 2024  737-53-1310
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  332 of 510

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-53-1310/file/bb8b076a46b3.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
