# Boeing Service Bulletin 737-55-1059: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-9068; AD 2017-06-14 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 737-55-1059](https://openairdocs.org/service-documents/boeing/sb-737-55-1059.md)
- Title as filed: SB-737-55-1059-01
- Pages: 85
- PDF: https://openairdocs.org/files/sha256/1c/81/1c811fb55d2e6a1dfb8d4d23f5709d98db7679177564308f865a04bb68b0f7ef
- Page: https://openairdocs.org/service-documents/boeing/sb-737-55-1059/file/1c811fb55d2e

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-55-1059
Original Issue: September 10, 1998
Revision 1: April 06, 2016
ATA System: 5510
SUBJECT: STABILIZERS - Horizontal Stabilizer - Lower Skin Inspection and Repair
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 1998 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
1 of 85
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
2 of 85
BOEING SERVICE BULLETIN 737-55-1059
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 32
4. Process Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
1. Kits/Parts: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2. Parts and Materials Supplied by the Operator: . . . . . . . . . . . . . . . . . . . . . . . . 36
3. Parts Modified and Reidentified: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4. Parts Removed and Not Replaced: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 37
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FIGURE 1: LEFT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION [Group 1,
Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
FIGURE 2: RIGHT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION [Group 1,
Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
FIGURE 3: STOP DRILL REPAIR  [Group 1, Configuration 1] . . . . . . . . . . . . . . . . . . . . . . 56
FIGURE 4: EXTERNAL DOUBLER REPAIR INSTALLATION  [Group 1, Configuration 1] . . . . . . . 57
FIGURE 5: HORIZONTAL STABILIZER LOWER SKIN SRM REPAIR OR EXTERNAL DOUBLER REPAIR
- POST-REPAIR INSPECTION  [Group 1, Configuration 2] . . . . . . . . . . . . . . . . . 61
FIGURE 6: LEFT HORIZONTAL STABILIZER LOWER SKIN OF UNREPAIRED AREAS - POST-REPAIR
INSPECTION [Group 1, Configuration 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
3 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 4

FIGURE 7: RIGHT HORIZONTAL STABILIZER LOWER SKIN OF UNREPAIRED AREAS - POST-REPAIR
INSPECTION [Group 1, Configuration 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
FIGURE 8: FORWARD FASTENER ROW OF EXTERNAL DOUBLER REPAIR - LOW FREQUENCY EDDY
CURRENT INSPECTION [Group 1, Configuration 2] . . . . . . . . . . . . . . . . . . . . . 67
FIGURE 9: CUT OUT REPAIR [Group 1, Configuration 1] . . . . . . . . . . . . . . . . . . . . . . . . 70
APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 1: LEFT AND RIGHT
HORIZONTAL STABILIZER LOWER SKINS THAT DO NOT HAVE A REPAIR INSTALLED –
INSPECTION AND REPAIR  [Group 1, Configuration 1] . . . . . . . . . . . . . . . . . . . 72
APPENDIX B: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 2: LEFT AND RIGHT
HORIZONTAL STABILIZER LOWER SKINS WITH AN EXISTING REPAIR INSTALLED -
POST-REPAIR INSPECTION AND REPAIR  [Group 1, Configuration 2] . . . . . . . . . . 77
APPENDIX C: INBOARD SKIN SPLICE REPAIRS - JACKING AND SHORING . . . . . . . . . . . . . . 81
APPENDIX D: INBOARD SKIN SPLICE REPAIRS - JACKS AND SHORING SUPPORT - REMOVAL . . 82
APPENDIX E: OUTBOARD SKIN SPLICE REPAIRS - JACKING AND SHORING . . . . . . . . . . . . . 83
APPENDIX F: OUTBOARD SKIN SPLICE REPAIRS - JACKS AND SHORING SUPPORT - REMOVAL . 84
APPENDIX G: BOEING PART DEMAND INTENT [Group 1, Configuration 1] . . . . . . . . . . . . . . . . 85
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
4 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 5

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-55-1059Original Issue: September 10, 1998
Revision 1: April 06, 2016
ATA System: 5510
SUBJECT: STABILIZERS - Horizontal Stabilizer - Lower Skin Inspection and Repair
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Airplane line numbers 3006 - 3132 were added to this service bulletin effectivity.
Effects of this Revision on airplanes on which the Original Issue was previously done:
ActionConditionGroup
Do detailed inspections of the hori-
zontal stabilizer lower skin for any
crack.
Left and right horizontal stabilizer
lower skins in Zone-A to Zone-F that
do not have a repair installed.
Group 1, Configuration 1
Do post-repair inspections of the
horizontal stabilizer lower skin for
any crack.
Left and right horizontal stabilizer
lower skins in Zone-A to Zone-F with
an existing repair, excluding Boeing
approved skin splice repairs.
Group 1, Configuration 2
REASON FOR REVISION
This revision is sent to introduce new repeat inspections for any crack in the horizontal stabilizer lower skin, an
updated external doubler repair, a new preventive modification, a new permanent skin splice repair and a new
Top Kit.
These sections were changed:
1. In Background, in the Summary section, added new information and a Summary Evaluation Table.
2. In Action, in the Summary section, changed instructions.
3. In Effectivity, in the Summary section, updated reference.
4. In Compliance, in the Summary section, removed information and added reference.
5. In Industry Support Information, in the Summary section, added warranty information.
6. In Manpower, in the Summary section, removed paragraph and added reference.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
5 of 85

### Page 6

7. In Material Information, in the Summary section, changed supplier information, added reference and
survey information.
8. In Summary illustration, in the Summary section, changed inspection area, added skin replacement
area and changed instructions.
9. In Paragraph 1.A., Effectivity, added line numbers 3006-3132 to Group 1, added note and divided the
effectivity into configurations.
10. In Paragraph 1.C., Reason, added new information and reason for this revision.
11. In Paragraph 1.D., Description, changed instructions and added maintenance zone table.
12. In Paragraph 1.E., Compliance, added new repeat inspection and corrective action information in tables.
13. In Paragraph 1.F., Approval, added approvals from European Aviation Safety Agency and Joint Aviation
Authorities.
14. In Paragraph 1.G., Manpower, updated information and added tables for new repairs, new preventive
modification, post-repair inspection and open hole inspection.
15. In Paragraph 1.H., Weight and Balance Changes, removed table for a doubler installation, added table
for new permanent skin splice repairs and preventive modification.
16. In Paragraph 1.J.1., References, updated existing data.
17. In Paragraph 1.J.2., Data Supplied with this Service Bulletin, added drawings supplied with this service
bulletin.
18. In Paragraph 1.K.1., Publications, added affected publication.
19. In Paragraph 1.K.2., Damage Tolerance Based Structural Inspections, added effects and reference.
20. In Paragraph 1.L., Interchangeability and Intermixability of Parts, added effect on parts.
21. In Paragraph 1.M., Software Accomplishment Summary, added effect.
22. In Paragraph 2.A., Material - Price and Availability, removed old Top Kits, added new Top Kit, revised
price.
23. In Paragraph 2.B., Industry Support Information, added warranty information.
24. In Paragraph 2.C., Parts Necessary for Each Airplane, updated the Kits/Parts table and the Parts and
Materials Supplied by the Operator table.
25. In Paragraph 3.A., General Information, revised the general notes in accordance with new requirements
and added terminating actions.
26. In Paragraph 3.B., Work Instructions, removed the permanent 0.063 inch doubler installation and repair,
added repairs, preventive modification, post-repair inspection and open hole inspection.
27. In Figure 1, inspections area extended and limited to left horizontal stabilizer lower skin only, additional
optional inspections added.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
6 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 7

28. Figure 2, added new figure for inspections.
29. Figure 3, separated repairs and moved to correct sequence.
30. Figure 4, changed fastener codes and added views.
31. In Figure 5, added post-repair inspection.
32. In Figure 6, added post-repair inspection of unrepaired bays on left horizontal stabilizer lower skin.
33. In Figure 7, added post-repair inspection of unrepaired bays on right horizontal stabilizer lower skin.
34. In Figure 8, added inspection of forward fastener row of external doubler repair.
35. In Figure 9, added repair as a separate figure.
36. Appendices A and B, added logic diagrams for compliance.
37. Appendix C, added jacking and shoring instructions for inboard skin splice repair.
38. Appendix D, added jacks and shoring support removal instructions for inboard skin splice repair.
39. Appendix E, added jacking and shoring instructions for outboard skin splice repair.
40. Appendix F, added jacks and shoring support removal instructions for outboard skin splice repair.
41. Appendix G, added Boeing Part Demand Intent.
The data given in Information Notice 737-55-1059 IN 01 and IN 02 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
September 10, 1998Original Issue:
April 06, 2016Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
7 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
8 of 85
BOEING SERVICE BULLETIN 737-55-1059
BLANK PAGE

### Page 9

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-55-1059Original Issue: September 10, 1998
Revision 1: April 06, 2016
ATA System: 5510
SUBJECT: STABILIZERS - Horizontal Stabilizer - Lower Skin Inspection and Repair
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of the work in this service bulletin will make sure that any crack found on the lower skins of the
horizontal stabilizer is detected and repaired. If the work given in this service bulletin is not accomplished, a
crack in the lower skin of the horizontal stabilizer may go undetected and grow in length. An undetected crack
and continuous operation of the airplane will cause reduced local stiffness of the stabilizer which can cause
heavy vibration leading to loss of structural integrity.
Nearly ninety cracks have been reported in horizontal stabilizer lower skins with most of them occurring between
Stabilizer Station (SSTA) 111.10 and 166.30. Ten operators reported cracks on eighteen airplanes outside this
range with fourteen of them inboard of SSTA 111.10. The cracks range in length from 0.25 inch to 3.75 inch
and the airplanes had between 12,670 and 69,569 flight cycles. The cracks started on the outer surface of the
skin where the chem-mill edge aligns with the edge of the lower flange of the rear spar. The cracks grew parallel
to the rear spar. High secondary bending stresses due to compression buckling of the skins and sonic fatigue
can cause the cracks to grow. Cracks also start from the fastener line nearest the chem-mill step. The cracks
were discovered during regular, scheduled maintenance inspections. Installation of new, non-chem milled skin
panels and an external doubler section have been used successfully over a number of years without reports of
additional cracking.
Boeing Structural Item Interim Advisory (SIIA) SIIA 737-250 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737-SRP-55-0014 and 737-SRP-55-0039 are related to this service
bulletin.
Boeing Fleet Team Digest (FTD) 737 FTD 55-06003 is related to this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
9 of 85

### Page 10

This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Group 1, Configuration 1:
Do a detailed inspection of left and right side lower skins of the horizontal stabilizers between SSTA 83.50 and
SSTA 249.10 for any crack. If any crack is found between SSTA 83.50 and SSTA 180.00, do the skin splice
repair and end inspections or install a Structural Repair Manual (SRM) repair or an external repair doubler and
do post repair inspections. SRM repair installation is an option for any crack found between SSTA 83.50 and
SSTA 157.10. External repair doubler installation is an option for any crack found between SSTA 111.10 and
SSTA 166.30. If any crack is found between SSTA 180.00 and SSTA 249.10, contact The Boeing Company for
repair instructions and do the repair. If no crack is found, continue inspections until the skin splice repair is done
or do a preventive modification to end inspections between SSTA 83.50 and SSTA 101.90 only.
Group 1, Configuration 2:
Do post repair inspections of left and right side lower skins of the horizontal stabilizers between SSTA 83.50
and SSTA 249.10 for any crack. If any crack is found between SSTA 83.50 and SSTA 180.00, do the skin splice
repair and end inspections. If any crack is found between SSTA 180.00 and SSTA 249.10, contact The Boeing
Company for repair instructions and do the repair. If no crack is found between SSTA 83.50 and SSTA 180.00,
continue post repair inspections until the skin splice repair is done. If no crack is found between SSTA 180.00
and SSTA 249.10, repeat post repair inspections.
EFFECTIVITY
All 737-300/-400/-500 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
10 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 11

COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance .
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and repair procedures given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Operators are encouraged to complete the survey provided in APPENDIX G of this service bulletin to help Boeing
predict the quantity and timing of the Boeing Supplied Kits/Parts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
11 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 12 (OCR)

BOEING SERVICE BULLETIN 737-55-1059
DO A DETAILED INSPECTION OF LEFT AND RIGHT SIDE
LOWER SKINS OF THE HORIZONTAL STABILIZERS FOR
ANY CRACK. IF ANY CRACK IS FOUND DO A SKIN
SPLICE REPAIR AND END INSPECTION OR, INSTALL A
SRM REPAIR OR AN EXTERNAL DOUBLER REPAIR AND DO
POST REPAIR INSPECTIONS. IF NO CRACK IS FOUND,
REPEAT INSPECT OR DO SKIN SPLICE REPAIRS OR DO A
PREVENTIVE MODIFICATION TO END INSPECTIONS.
RIGHT STABILIZER  ZONE-B  ZONE-A  LEFT STABILIZER
ZONE-D  ZONE-C  FRONT SPAR
ZONE-F  ZONE-E
SSTA 83.50
SSTA 105.70  REAR SPAR
SSTA 180.00
FWD
DETAILED INSPECTION
AREA  SSTA 249.10
HORIZONTAL STABILIZER LOWER SKIN LOOKING UP  S45206
Original Issue: September 10, 1998
Revision 1: April 06, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-55-1059
Work - See page 1 for details.  12 of 85

### Page 13

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-55-1059
Original Issue: September 10, 1998
Revision 1: April 06, 2016
ATA System: 5510
SUBJECT: STABILIZERS - Horizontal Stabilizer - Lower Skin Inspection and Repair
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is applicable to 737-300/-400/-500 Airplanes, line numbers 1001-3132 in one
Group. The Variable Numbers and Group Information for the applicable airplanes is given below.
Refer to Service Bulletin Index Document D6-19567, Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
NOTE: Prior to the release date of SB 737-55-1059 Revision 1, if a Boeing ODA FAA Form
8100-9 approved skin splice repair was installed, and the splice and replaced segment
of skin is in the same location as the part 4, part 5, part 6, or part 7 skin splice repair
given in paragraph 3.B., Work Instructions of this service bulletin, then the corresponding
paragraph 3.A., General Information note regarding inspection termination applies.
DESCRIPTIONCONFIGURATIONGROUP
737-300/-400/-500 airplanes. Line number 1001 to 3132.-1
Left and right horizontal stabilizer lower skins in Zone-A to Zone-F
that do not have a repair installed.
1
Left and right horizontal stabilizer lower skins in Zone-A to Zone-F
with an existing repair, excluding Boeing approved skin splice repairs.
2
Airplane Models:
737-300, 737-400, 737-500
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
13 of 85

### Page 14

GroupVariable Number
1PJ301 - PJ302
1PJ551 - PJ561
1PJ601 - PJ615
1PJ811
1PJ816 - PJ817
1PM381 - PM399
1PM401 - PM417
1PM541 - PM564
1PP001 - PP054
1PP101 - PP169
1PP181 - PP199
1PP201 - PP205
1PP221
1PP231 - PP243
1PP281 - PP286
1PP301 - PP305
1PP351 - PP353
1PP376 - PP384
1PP391 - PP393
1PP401 - PP440
1PP471 - PP475
1PP501 - PP522
1PP631 - PP634
1PP651 - PP652
1PP671 - PP699
1PP701 - PP733
1PP771 - PP779
1PP801 - PP808
1PP821 - PP827
1PP831 - PP848
1PP851 - PP852
1PP861 - PP877
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
14 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 15

GroupVariable Number
1PP891 - PP899
1PP901 - PP936
1PP946 - PP948
1PP951 - PP952
1PP961 - PP967
1PP981 - PP991
1PP993
1PQ001 - PQ016
1PQ026 - PQ041
1PQ051 - PQ092
1PQ101 - PQ199
1PQ201 - PQ202
1PQ221 - PQ237
1PQ241 - PQ243
1PQ251 - PQ267
1PQ281 - PQ299
1PQ301 - PQ307
1PQ331 - PQ332
1PQ341 - PQ348
1PQ361 - PQ373
1PQ391 - PQ395
1PQ401 - PQ418
1PQ421
1PQ431 - PQ438
1PQ447 - PQ448
1PQ451
1PQ454
1PQ471 - PQ475
1PQ479 - PQ481
1PQ486 - PQ487
1PQ491 - PQ493
1PQ771 - PQ772
1PQ791 - PQ793
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
15 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 16

GroupVariable Number
1PQ801 - PQ805
1PQ931 - PQ935
1PQ951
1PQ971 - PQ997
1PR001 - PR017
1PR021 - PR034
1PR041 - PR045
1PR061 - PR072
1PR077 - PR082
1PR091 - PR092
1PR096
1PR101
1PR121 - PR122
1PR131 - PR132
1PR141 - PR143
1PR161 - PR172
1PR181
1PS601 - PS631
1PS636 - PS638
1PS641 - PS644
1PS651 - PS657
1PS666 - PS669
1PS691 - PS692
1PS701 - PS706
1PS751 - PS799
1PS811
1PS836 - PS837
1PS841 - PS846
1PS851 - PS852
1PS856
1PS861 - PS863
1PS866 - PS868
1PS871 - PS874
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
16 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 17

GroupVariable Number
1PS896 - PS897
1PS901 - PS941
1PS956 - PS957
1PS961 - PS963
1PS971 - PS978
1PT001 - PT015
1PT021 - PT031
1PT041 - PT064
1PT101 - PT105
1PT121 - PT138
1PT146 - PT148
1PT161 - PT170
1PT181 - PT188
1PT211 - PT220
1PT295
1PT301 - PT309
1PT331 - PT360
1PT381 - PT399
1PT401 - PT438
1PT501 - PT517
1PT561 - PT565
1PT581 - PT586
1PT611 - PT621
1PT641 - PT644
1PT651 - PT656
1PT671 - PT672
1PT681 - PT685
1PT701 - PT703
1PT716 - PT717
1PT721 - PT725
1PT801 - PT834
1PT851 - PT854
1PT871 - PT886
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
17 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 18

GroupVariable Number
1PT901 - PT930
1PT971 - PT973
1PT981 - PT985
1PT996
1PU001 - PU025
1PU301
1PU311 - PU313
1PV001 - PV055
1PV201 - PV209
1PV226 - PV229
1PV231 - PV237
1PV271 - PV272
1PV281 - PV287
1PV296
1PV301 - PV302
1PV351
1PV356 - PV357
1PW001 - PW054
1PW061 - PW068
1PW072
1PW086 - PW088
1PW091 - PW094
1PW101 - PW102
1PW106
1PW111 - PW120
1PW156 - PW157
1PW161 - PW171
1PW201 - PW252
1PW261 - PW268
1PW271 - PW276
1PW278
1PW281 - PW293
1PW296
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
18 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 19

GroupVariable Number
1PW301 - PW327
1PW401 - PW408
1PW411 - PW418
1PW421 - PW424
1PW431 - PW435
1PW441 - PW450
1PW461 - PW467
1PW501 - PW504
1PW511 - PW522
1PW524 - PW550
1PW556 - PW557
1PW561 - PW564
1PW571 - PW576
1PW591 - PW596
1PW611 - PW622
1PW631 - PW637
1PW661 - PW662
1PW681 - PW683
1PW701 - PW702
1PW711 - PW717
1PW741 - PW742
1PW761
1PW771
1PW831
1PW851 - PW856
2. Spares Affected
None.
B. Concurrent Requirements
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
19 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 20

C. Reason
Accomplishment of the work in this service bulletin will make sure that any crack found on the lower
skins of the horizontal stabilizer is detected and repaired. If the work given in this service bulletin is not
accomplished, a crack in the lower skin of the horizontal stabilizer may go undetected and grow in
length. An undetected crack and continuous operation of the airplane will cause reduced local stiffness
of the stabilizer which can cause heavy vibration leading to loss of structural integrity.
Nearly ninety cracks have been reported in horizontal stabilizer lower skins with most of them occurring
between Stabilizer Station (SSTA) 111.10 and 166.30. Ten operators reported cracks on eighteen
airplanes outside this range with fourteen of them inboard of SSTA 111.10. The cracks range in length
from 0.25 inch to 3.75 inch and the airplanes had between 12,670 and 69,569 flight cycles. The cracks
started on the outer surface of the skin where the chem-mill edge aligns with the edge of the lower
flange of the rear spar. The cracks grew parallel to the rear spar. High secondary bending stresses
due to compression buckling of the skins and sonic fatigue can cause the cracks to grow. Cracks also
start from the fastener line nearest the chem-mill step. The cracks were discovered during regular,
scheduled maintenance inspections. Installation of new, non-chem milled skin panels and an external
doubler section have been used successfully over a number of years without reports of additional
cracking.
Boeing Structural Item Interim Advisory (SIIA) SIIA 737-250 is related to this service bulletin.
Boeing Service Related Problem (SRP) 737-SRP-55-0014 and 737-SRP-55-0039 are related to this
service bulletin.
Boeing Fleet Team Digest (FTD) 737 FTD 55-06003 is related to this service bulletin.
This revision is sent to introduce new repeat inspections for any crack in the horizontal stabilizer lower
skin, an updated external doubler repair, a new preventive modification, a new permanent skin splice
repair and a new Top Kit.
D. Description
Group 1, Configuration 1:
Do a detailed inspection of left and right side lower skins of the horizontal stabilizers between SSTA
83.50 and SSTA 249.10 for any crack. If any crack is found between SSTA 83.50 and SSTA 180.00,
do the skin splice repair and end inspections or install a Structural Repair Manual (SRM) repair or an
external repair doubler and do post repair inspections. SRM repair installation is an option for any crack
found between SSTA 83.50 and SSTA 157.10. External repair doubler installation is an option for any
crack found between SSTA 111.10 and SSTA 166.30. If any crack is found between SSTA 180.00 and
SSTA 249.10, contact The Boeing Company for repair instructions and do the repair. If no crack is
found, continue inspections until the skin splice repair is done or do a preventive modification to end
inspections between SSTA 83.50 and SSTA 101.90 only.
Group 1, Configuration 2:
Do post repair inspections of left and right side lower skins of the horizontal stabilizers between SSTA
83.50 and SSTA 249.10 for any crack. If any crack is found between SSTA 83.50 and SSTA 180.00,
do the skin splice repair and end inspections. If any crack is found between SSTA 180.00 and SSTA
249.10, contact The Boeing Company for repair instructions and do the repair. If no crack is found
between SSTA 83.50 and SSTA 180.00, continue post repair inspections until the skin splice repair is
done. If no crack is found between SSTA 180.00 and SSTA 249.10, repeat post repair inspections.
Effects of this Revision on airplanes on which the Original Issue was previously done:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
20 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 21

ActionConditionGroup
Do detailed inspections of the hori-
zontal stabilizer lower skin for any
crack.
Left and right horizontal stabilizer
lower skins in Zone-A to Zone-F that
do not have a repair installed.
Group 1, Configuration 1
Do post-repair inspections of the
horizontal stabilizer lower skin for
any crack.
Left and right horizontal stabilizer
lower skins in Zone-A to Zone-F with
an existing repair, excluding Boeing
approved skin splice repairs.
Group 1, Configuration 2
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
709, 710737-300, 737-400, 737-500
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Logic diagrams showing compliance tasks and compliance times are included as an aid in APPENDIX
A and APPENDIX B.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
NOTE: Prior to the release date of SB 737-55-1059 Revision 1, if a Boeing ODA FAA Form 8100-9
approved skin splice repair was installed, and the splice and replaced segment of skin is in
the same location as the part 4, part 5, part 6, or part 7 skin splice repair given in paragraph
3.B., Work Instructions of this service bulletin, then the corresponding paragraph 3.A., General
Information note regarding inspection termination applies.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
21 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 22

Group 1, Configuration 1:
Table 1: Left and Right Horizontal Stabilizer Lower Skins That Do Not Have a Repair Installed - Inspection
and Repair
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 7,000
horizontal stabi-
lizer flight cycles
after the Revi-
sion 1 date of
this service bul-
letin.
Before 15,000
total horizontal
stabilizer flight
cycles.
Do PART 1: DETAILED
INSPECTION OF THE
HORIZONTAL STABILIZ-
ER LOWER SKIN for any
crack.
All left and right horizontal
stabilizer lower skins that
do not have a repair in-
stalled in Zone-A to Zone-
F.
4,500 flight cycles.-Repeat PART 1: DE-
TAILED INSPECTION
OF THE HORIZONTAL
STABILIZER LOWER
SKIN for any crack. (a)
(b) (c) (d) (e)
CONDITION 1:
NO CRACK FOUND IN
ZONE-A or ZONE-B or
ZONE-C or ZONE-D or
ZONE-E or ZONE-F.
-Before further flight.OPTION 1: Do PART 4:
SKIN SPLICE REPAIR IN
ZONE-A. (a)
CONDITION 2: ANY
CRACK FOUND IN ZONE-
A.
-Before further flight.OPTION 2: Do an exter-
nal doubler repair in ac-
cordance with the SRM.
(f) (g)
-Before further flight.OPTION 1: Do PART 5:
SKIN SPLICE REPAIR IN
ZONE-B. (b)
CONDITION 3: ANY
CRACK FOUND IN ZONE-
B.
-Before further flight.OPTION 2: Do an exter-
nal doubler repair in ac-
cordance with the SRM.
(f) (g)
-Before further flight.OPTION 1: Do PART 6:
SKIN SPLICE REPAIR IN
ZONE-C. (c)
CONDITION 4: ANY
CRACK FOUND IN ZONE-
C.
-Before further flight.OPTION 2: Do an exter-
nal doubler repair in ac-
cordance with the SRM.
(f) (g) (h)
-Before further flight.OPTION 3: Do PART 8:
EXTERNAL DOUBLER
REPAIR. (f) (i)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
22 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 23

Group 1, Configuration 1:
Table 1: Left and Right Horizontal Stabilizer Lower Skins That Do Not Have a Repair Installed - Inspection
and Repair
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.OPTION 1: Do PART 7:
SKIN SPLICE REPAIR IN
ZONE-D. (d)
CONDITION 5: ANY
CRACK FOUND IN ZONE-
D.
-Before further flight.OPTION 2: Do an exter-
nal doubler repair in ac-
cordance with the SRM.
(f) (g) (h)
-Before further flight.OPTION 3: Do PART 8:
EXTERNAL DOUBLER
REPAIR. (f) (i)
-Before further flight.Contact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 6: ANY
CRACK FOUND IN ZONE-
E or ZONE-F.
(a) Accomplishment of PART 4: SKIN SPLICE REPAIR IN ZONE-A is terminating action to the inspections
between SSTA 83.50 and SSTA 111.10.
(b) Accomplishment of PART 5: SKIN SPLICE REPAIR IN ZONE-B is terminating action to the inspections
between SSTA 83.50 and SSTA 111.10.
(c) Accomplishment of PART 6: SKIN SPLICE REPAIR IN ZONE-C is terminating action to the inspections
between SSTA 101.90 and SSTA 184.70.
(d) Accomplishment of PART 7: SKIN SPLICE REPAIR IN ZONE-D is terminating action to the inspections
between SSTA 101.90 and SSTA 184.70.
(e) Accomplishment of PART 2: PREVENTIVE MODIFICATION IN ZONE-A or PART 3: PREVENTIVE
MODIFICATION IN ZONE-B is terminating action to the inspections between SSTA 83.50 and SSTA
101.90.
(f) Refer to Table 2 for compliance information related to post-repair inspections of SRM doubler repairs or
external doubler repairs.
(g) Do the repair in accordance with 737-300 SRM 55-10-01, Repair 13 or 737-400 SRM 55-10-01, Repair
13 or 737-500 SRM 55-10-01, Repair 13.
(h) This option only applies for any crack found in ZONE-C or ZONE-D between SSTA 105.70 and SSTA
157.10.
(i) This option only applies for any crack found in ZONE-C or ZONE-D between SSTA 111.10 and SSTA
166.30.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
23 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 24

Group 1, Configuration 2:
Table 2: Left and Right Horizontal Stabilizer Lower Skins With An Existing Repair Installed - Post-Repair
Inspection and Repair
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 12
months after the
Revision 1 date
of this service
bulletin.
Within 12
months after in-
stallation of the
repair.
Do PART 9: POST-RE-
PAIR INSPECTION OF
THE HORIZONTAL STA-
BILIZER LOWER SKIN
for any crack and for any
loose or any missing fas-
tener. (a) (b)
All left and right horizontal
stabilizer lower skins with
an existing repair installed.
(a)
12 months.-Repeat PART 9: POST-
REPAIR INSPECTION
OF THE HORIZONTAL
STABILIZER LOWER
SKIN for any crack and
for any loose or any
missing fastener. (b) (c)
(d) (e) (f)
CONDITION 7:
NO CRACK AND NO
LOOSE OR MISSING
FASTENER FOUND IN
ZONE-A or ZONE-B or
ZONE-C or ZONE-D or
ZONE-E or ZONE-F.
-Before further flight.Do PART 4: SKIN
SPLICE REPAIR IN
ZONE-A. (c)
CONDITION 8: ANY
CRACK FOUND IN ZONE-
A.
-Before further flight.Do PART 5: SKIN
SPLICE REPAIR IN
ZONE-B. (d)
CONDITION 9: ANY
CRACK FOUND IN ZONE-
B.
-Before further flight.Do PART 6: SKIN
SPLICE REPAIR IN
ZONE-C. (e)
CONDITION 10: ANY
CRACK FOUND IN ZONE-
C.
-Before further flight.Do PART 7: SKIN
SPLICE REPAIR IN
ZONE-D. (f)
CONDITION 11: ANY
CRACK FOUND IN ZONE-
D.
-Before further flight.Contact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 12: ANY
CRACK FOUND IN ZONE-
E or ZONE-F.
-Before further flight.Do PART 10: OPEN
HOLE INSPECTION for
any corrosion and any
hole elongation and for
any crack.
CONDITION 13: ANY
LOOSE OR ANY MISSING
FASTENER FOUND, NO
CRACK FOUND IN ZONE-
A OR ZONE-B OR ZONE-
C OR ZONE-D.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
24 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 25

Group 1, Configuration 2:
Table 2: Left and Right Horizontal Stabilizer Lower Skins With An Existing Repair Installed - Post-Repair
Inspection and Repair
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Before further flight.CONDITION 14 (ACTION
1): Install new fastener.
(g)
CONDITION 14: NO COR-
ROSION, NO HOLE
ELONGATION AND NO
CRACK FOUND IN ANY
HOLE OF LOOSE OR
MISSING FASTENERS IN
REPAIRED AREAS.
12 months.-CONDITION 14 (ACTION
2): Repeat PART 9:
POST-REPAIR INSPEC-
TION OF THE HORIZON-
TAL STABILIZER LOW-
ER SKIN for any crack
and for any loose or any
missing fastener. (b) (c)
(d) (e) (f)
-Before further flight.CONDITION 15 (ACTION
1): Contact The Boeing
Company for repair in-
structions and do the re-
pair.
CONDITION 15: ANY
CORROSION OR ANY
HOLE ELONGATION OR
ANY CRACK FOUND IN
ANY HOLE OF LOOSE OR
MISSING FASTENERS IN
REPAIRED AREAS. 12 months.-CONDITION 15 (ACTION2): Repeat PART 9:
POST-REPAIR INSPEC-
TION OF THE HORIZON-
TAL STABILIZER LOW-
ER SKIN for any crack
and for any loose or any
missing fastener. (b) (c)
(d) (e) (f)
(a) Prior to the release date of SB 737-55-1059 Revision 1, if a Boeing ODA FAA Form 8100-9 approved
skin splice repair was installed, and the splice and replaced segment of skin is in the same location as
the part 4, part 5, part 6, or part 7 skin splice repair given in paragraph 3.B., Work Instructions of this
service bulletin, then the corresponding paragraph 3.A., General Information note regarding inspection
termination applies.
(b) Doublers installed with solid rivets do not need to be inspected for any loose or any missing fasteners.
(c) Accomplishment of PART 4: SKIN SPLICE REPAIR IN ZONE-A is terminating action to the inspections
between SSTA 83.50 and SSTA 111.10.
(d) Accomplishment of PART 5: SKIN SPLICE REPAIR IN ZONE-B is terminating action to the inspections
between SSTA 83.50 and SSTA 111.10.
(e) Accomplishment of PART 6: SKIN SPLICE REPAIR IN ZONE-C is terminating action to the inspections
between SSTA 101.90 and SSTA 184.70.
(f) Accomplishment of PART 7: SKIN SPLICE REPAIR IN ZONE-D is terminating action to the inspections
between SSTA 101.90 and SSTA 184.70.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
25 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 26

Group 1, Configuration 2:
Table 2: Left and Right Horizontal Stabilizer Lower Skins With An Existing Repair Installed - Post-Repair
Inspection and Repair
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
(g) For repairs installed in accordance with an SRM, install new fastener in accordance with 737-300 SRM
55-10-01, Repair 13 or 737-400 SRM 55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13. For
repairs installed in accordance with FIGURE 4 of this service bulletin, install new fastener in accordance
with FIGURE 4 of this service bulletin. Only non-solid rivet repairs are being inspected.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the man-hours necessary to do this inspection, repair and
modification for each airplane. This estimate is for direct labor only, done by an experienced crew.
Adjust the estimate with operator man-hour data if necessary. The estimate does not include lost time.
These are some examples of lost time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1, Configuration 1:
PART 1: DETAILED INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
0.750.751FIGURE 1
0.750.751FIGURE 2
1.501.50TOTAL FOR EACH AIRPLANE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
26 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 27

Group 1, Configuration 1:
PART 2: PREVENTIVE MODIFICATION IN ZONE-A
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
2.252.251Modify
7.0028.004Close
14.2550.25TOTAL FOR EACH STABILIZER
1.757.004Access - OPTION 2
2.252.251Modify
1.757.004Close
5.7516.25TOTAL FOR EACH STABILIZER
Group 1, Configuration 1:
PART 3: PREVENTIVE MODIFICATION IN ZONE-B
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
2.252.251Modify
7.0028.004Close
14.2550.25TOTAL FOR EACH STABILIZER
1.757.004Access - OPTION 2
2.252.251Modify
1.757.004Close
5.7516.25TOTAL FOR EACH STABILIZER
PART 4: SKIN SPLICE REPAIR IN ZONE-A
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
12.2549.004Repair
7.0028.004Close
24.2597.00TOTAL FOR LEFT STABILIZER
1.757.004Access - OPTION 2
12.2549.004Repair
1.757.004Close
15.7563.00TOTAL FOR LEFT STABILIZER
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
27 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 28

PART 5: SKIN SPLICE REPAIR IN ZONE-B
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTON 1
12.2549.004Repair
7.0028.004Close
24.2597.00TOTAL FOR RIGHT STABILIZER
1.757.004Access - OPTION 2
12.2549.004Repair
1.757.004Close
15.7563.00TOTAL FOR RIGHT STABILIZER
PART 6: SKIN SPLICE REPAIR IN ZONE-C
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
40.75163.004Repair
7.0028.004Close
52.75211.00TOTAL FOR LEFT STABILIZER
1.757.004Access - OPTION 2
40.75163.004Repair
1.757.004Close
44.25177.00TOTAL FOR LEFT STABILIZER
PART 7: SKIN SPLICE REPAIR IN ZONE-D
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
40.75163.004Repair
7.0028.004Close
52.75211.00TOTAL FOR RIGHT STABILIZER
1.757.004Access - OPTION 2
40.75163.004Repair
1.757.004Close
44.25177.00TOTAL FOR RIGHT STABILIZER
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
28 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 29

Group 1, Configuration 1:
PART 8: EXTERNAL DOUBLER REPAIR
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
5.0020.004Access - OPTION 1
0.250.251FIGURE 3
1.751.751FIGURE 4
7.0028.004Close
14.0050.00TOTAL FOR EACH REPAIR
5.0020.004Access - OPTION 1
2.002.001FIGURE 9
1.751.751FIGURE 4
7.0028.004Close
15.7551.75TOTAL FOR EACH REPAIR
2.505.002Access - OPTION 2
0.250.251FIGURE 3
1.751.751FIGURE 4
2.505.002Close
7.0012.00TOTAL FOR EACH REPAIR
2.505.002Access - OPTION 2
2.002.001FIGURE 9
1.751.751FIGURE 4
2.505.002Close
8.7513.75TOTAL FOR EACH REPAIR
Group 1, Configuration 2:
PART 9: POST-REPAIR INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
0.500.501FIGURE 5
0.750.751FIGURE 6 or FIGURE 7
2.002.001FIGURE 8
3.253.25TOTAL FOR EACH REPAIR
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
29 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 30

Group 1, Configuration 2:
PART 10: OPEN HOLE INSPECTION
Elapsed Time (Hours)Man-HoursNumber of PersonsTask
0.050.051Remove fastener
0.050.051Inspection for corrosion
0.050.051Inspection for hole elonga-
tion
0.050.051High Frequency Eddy Cur-
rent (HFEC) inspection for
any crack
0.050.051Install fastener
0.250.25TOTAL FOR EACH HOLE
H. Weight and Balance Changes
Group 1, Configuration 1:
The weight and balance changes for the 0.080 inch doubler installation on one side of the horizontal
stabilizer are:
Group 1, Configuration 1:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)Airplane
+3,000+2.3737-300
+3,000+2.3737-400
+3,000+2.3737-500
Group 1, Configuration 1:
The weight and balance changes for the preventive modification in either Zone-A or Zone-B on one
side of the horizontal stabilizer are:
Group 1, Configuration 1:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)Airplane
+249.3+0.2737-300
+259.2+0.2737-400
+241.3+0.2737-500
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
30 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 31

The weight and balance changes for the skin splice repair in ZONE-A are:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)
Airplane
+1,200+0.9737-300
+1,200+0.9737-400
+1,200+0.9737-500
The weight and balance changes for the skin splice repair in ZONE-B are:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)Airplane
+1,200+0.9737-300
+1,200+0.9737-400
+1,200+0.9737-500
The weight and balance changes for the skin splice repair in ZONE-C are:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)Airplane
+4,000+3.1737-300
+4,000+3.1737-400
+4,000+3.1737-500
The weight and balance changes for the skin splice repair in ZONE-D are:
Change in Moment (Pound-Inch-
es)
Change in Weight (Pounds)Airplane
+4,000+3.1737-300
+4,000+3.1737-400
+4,000+3.1737-500
I. Electrical Load Data
Not applicable.
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 737-SRP-55-0014, 737-SRP-55-0039
b. Boeing Structural Item Interim Advisory (SIIA) 737-250
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
31 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 32

c. Standard Overhaul Practices Manual (SOPM) 20-50-01
d. 737 Fleet Team Digest (FTD) 55-06003
e. 737 Non-Destructive Testing (NDT) Manual Part 6, 51-00-00, Part 6, 51-00-26, Part 6, 53-30-23,
Part 6, 53-30-25, Part 6, 55-10-08
f. 737-300/400/500 Aircraft Maintenance Manual (AMM) 07-11-11, 27-21-00, 27-31-00, 27-41-11
g. 737-300 Structural Repair Manual (SRM) 51-10-02, 51-20-01, 51-40-02, 51-40-08, 51-50-02,
55-10-01
h. 737-400 Structural Repair Manual (SRM) 51-10-02, 51-20-01, 51-40-02, 51-40-08, 51-50-02,
55-10-01
i. 737-500 Structural Repair Manual (SRM) 51-10-02, 51-20-01, 51-40-02, 51-40-08, 51-50-02,
55-10-01
2. Data Supplied with this Service Bulletin:
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No
--1HORIZONTAL STABILIZER, LOWER SKIN
- SERVICE GENERAL REPAIR
692A5001
--2
--3
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
4. Process Data:
None.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
51-20, 51-40, 51-50, 55-10737 Structural Repair Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS. DTI requirements for the structure affected
are contained in Paragraph 1.E., Compliance of this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
32 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 33

L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
33 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 34

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
34 of 85
BOEING SERVICE BULLETIN 737-55-1059
BLANK PAGE

### Page 35

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in the kits in Paragraph 2.C., Parts Necessary
for Each Airplane. As an alternative, operators can purchase the kit from Boeing Spares. The Boeing
price data shown below is given for planning purposes. Supply data can be given if requested. The
kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
Prices are in United States Dollars. Terms: Net 30 days
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST
RESPONDER AT FR@BOEING.COM FOR THE LATEST PRICE INFORMATION
Unit Price as of the
Revision 1 date of
this Service Bul-
letin (US Dollars)
NameKit Part Number
$721.00Fastener Kit65C37853-66
Operators are encouraged to complete the survey provided in APPENDIX G of this service bulletin to
help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and repair procedures given in this
service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
NOTE: If purchased from Boeing, one top kit is necessary for each horizontal stabilizer. Two top
kits are necessary for each airplane. Materials given in Paragraph 2.C.2., Parts and
Materials Supplied by the Operator  are also necessary.
NOTE: Fastener kit 65C37853-44 has been replaced by fastener kit 65C37853-66.
NOTE: Fastener kit 65C37853-66 is necessary to accomplish Paragraph 3.B., Work Instructions,
PART 8: EXTERNAL DOUBLER REPAIR.
To get the kits shown below, refer to Paragraph 2.A., Material - Price and Availability .
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
35 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 36

Group 1, Configuration 1:
Kit 65C37853
NotesExisting Part
Number
NameQtyNew Part Number
-66
-TOP KIT,
RETROFIT - FAS-
TENER KIT
-65C37853-66
-WASHER10266-2955-11
-WASHER2566-2955-47
(a)-BOLT2BACB30NW6K10
(a)-BOLT-CSK. HEAD2BACB30NW6K9
-COLLAR4BACC30M6
(a)-RIVET, BLIND114NAS1399D5AB2
(a)-RIVET, BLIND18NAS1399D5AB4
(a)-RIVET, BLIND7NAS1399D5AB5
(a)-RIVET, BLIND6NAS1399D6AB10
(a)-RIVET, BLIND1NAS1399D6AB4
(a)-RIVET, BLIND66NAS1399D6AB7
(a)-RIVET, BLIND21NAS1399D6AB8
(a)-RIVET, BLIND4NAS1399D6AB9
(a) If grip length shown is not available at Boeing, fasteners supplied in kits
may be one grip length longer than indicated. Also, if any fasteners part
numbers listed are not available or have been superseded, substitute
fasteners may be supplied in kits.
2. Parts and Materials Supplied by the Operator:
NamePart NumberQTY
Doubler0.080 inch thick 2024-T3 Clad AluminumAs Necessary
Filler0.050 inch thick 2024-T3 Clad AluminumAs Necessary
SealantBMS 5-95 (a)As Necessary
PrimerBMS 10-11, Type I (a)As Necessary
PaintBMS 10-11, Type II (a)As Necessary
(a) See the Qualified Products List at the end of the Boeing Material Specification
(BMS) for supplier data.
NOTE: The parts listed above are only necessary to install an optional external doubler repair.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
36 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 37

Refer to 692A5001 for parts and materials necessary to accomplish skin splice repair.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
37 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 38

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
38 of 85
BOEING SERVICE BULLETIN 737-55-1059
BLANK PAGE

### Page 39

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 737 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 737
Aircraft Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
39 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 40

7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
12. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
13. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
14. Refer to APPENDIX A and APPENDIX B for logic diagrams. Logic diagrams are
provided as an aid only. Information contained in Paragraph 1.E., Compliance is the
primary source for compliance times. Information in Paragraph 3.B., Work Instructions
is the primary source for tasks required for compliance.
15. Accomplishment of PART 2: PREVENTIVE MODIFICATION IN ZONE-A or PART
3: PREVENTIVE MODIFICATION IN ZONE-B is terminating action to the inspections
between SSTA 83.50 and SSTA 101.90.
16. Accomplishment of PART 4: SKIN SPLICE REPAIR IN ZONE-A is terminating action
to the inspections between SSTA 83.50 and SSTA 111.10.
17. Accomplishment of PART 5: SKIN SPLICE REPAIR IN ZONE-B is terminating action
to the inspections between SSTA 83.50 and SSTA 111.10.
18. Accomplishment of PART 6: SKIN SPLICE REPAIR IN ZONE-C is terminating action
to the inspections between SSTA 101.90 and SSTA 184.70.
19. Accomplishment of PART 7: SKIN SPLICE REPAIR IN ZONE-D is terminating action
to the inspections between SSTA 101.90 and SSTA 184.70.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
40 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 41

B. WORK INSTRUCTIONS
Group 1, Configuration 1:
WARNING: BEFORE MOVING HORIZONTAL STABILIZER, MAKE CERTAIN THAT AREAS AROUND
HORIZONTAL STABILIZER AND ELEVATORS ARE CLEAR OF PERSONNEL AND
EQUIPMENT AND THAT UPPER TAIL CONE DOORS ARE CLOSED. THE MOVEMENT
OF SURFACES CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO
EQUIPMENT.
WARNING: DEPRESSURIZE THE RUDDER, ELEVATORS, AND HORIZONTAL STABILIZER.
PRESSURE IN THESE HYDRAULIC SYSTEMS CAN ALLOW COMPONENTS TO BE
MOVED SUDDENLY BY ANOTHER PERSON. THIS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.
1. Remove the pressure from systems A and B for the rudder. Refer to 737-300/400/500 AMM
27-21-00 as an accepted procedure.
2. Remove the pressure from the elevators. Refer to 737-300/400/500 AMM 27-31-00 as an accepted
procedure.
3. Set the stabilizer trim cutout switches to CUTOUT.
4. Open the following circuit breakers and attach DO-NOT-CLOSE tags.
a. P6 Circuit Breaker Panel:
(1) STABILIZER TRIM ACTUATOR.
(2) STABILIZER TRIM CONT.
b. P18 Circuit Breaker Panel:
(1) AUTOPILOT STABILIZER TRIM SERVO.
5. Use the stabilizer trim wheel on the control stand to set the horizontal stabilizer at zero degrees
(3 units of trim).
6. Install the trim lock assembly, F71336-501, on the stabilizer trim wheel.
a. Turn the trim wheel to put the handle at the top of the wheel.
b. Adjust the height of the trim lock to set the trim wheel handle tightly in the bottom of the yoke.
c. Install the pin through the yoke and install the safety pin.
7. Do PART 1: DETAILED INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN for
any crack.
a. CONDITION 1: NO CRACK FOUND IN ZONE-A or ZONE-B or ZONE-C or ZONE-D or ZONE-E
or ZONE-F.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
41 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 42

(1) Repeat PART 1: DETAILED INSPECTION OF THE HORIZONTAL STABILIZER LOWER
SKIN for any crack.
b. CONDITION 2: ANY CRACK FOUND IN ZONE-A.
(1) OPTION 1: Do PART 4: SKIN SPLICE REPAIR IN ZONE-A.
(2) OPTION 2: Do an external doubler repair in accordance with 737-300 SRM 55-10-01,
Repair 13 or 737-400 SRM 55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13.
NOTE: Refer to Table 2 for compliance information related to post-repair inspections
of SRM doubler repairs or external doubler repairs.
c. CONDITION 3: ANY CRACK FOUND IN ZONE-B.
(1) OPTION 1: Do PART 5: SKIN SPLICE REPAIR IN ZONE-B.
(2) OPTION 2: Do an external doubler repair in accordance with 737-300 SRM 55-10-01,
Repair 13 or 737-400 SRM 55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13.
NOTE: Refer to Table 2 for compliance information related to post-repair inspection of
SRM doubler repair or external doubler repairs.
d. CONDITION 4: ANY CRACK FOUND IN ZONE-C.
(1) OPTION 1: Do PART 6: SKIN SPLICE REPAIR IN ZONE-C.
(2) OPTION 2: Do an external doubler repair in accordance with 737-300 SRM 55-10-01,
Repair 13 or 737-400 SRM 55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13.
NOTE: Refer to Table 2 for compliance information related to post-repair inspection of
SRM doubler repair or external doubler repairs.
(3) OPTION 3: Do PART 8: EXTERNAL DOUBLER REPAIR.
NOTE: Refer to Table 2 for compliance information related to post-repair inspection of
SRM doubler repair or external doubler repairs.
NOTE: This option only applies for any crack found in ZONE-C or ZONE-D between
SSTA 111.10 and SSTA 166.30.
e. CONDITION 5: ANY CRACK FOUND IN ZONE-D.
(1) OPTION 1: Do PART 7: SKIN SPLICE REPAIR IN ZONE-D.
(2) OPTION 2: Do an external doubler repair in accordance with 737-300 SRM 55-10-01,
Repair 13 or 737-400 SRM 55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13.
NOTE: Refer to Table 2 for compliance information related to post-repair inspection of
SRM doubler repair or external doubler repairs.
NOTE: This option only applies for any crack found in ZONE-C or ZONE-D between
SSTA 105.70 and SSTA 157.10.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
42 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 43

(3) OPTION 3: Do PART 8: EXTERNAL DOUBLER REPAIR.
NOTE: Refer to Table 2 for compliance information related to post-repair inspection of
SRM doubler repair or external doubler repairs.
NOTE: This option only applies for any crack found in ZONE-C or ZONE-D between
SSTA 111.10 and SSTA 166.30.
f. CONDITION 6: ANY CRACK FOUND IN ZONE-E OR ZONE-F.
(1) Contact The Boeing Company for repair instructions and do the repair.
WARNING: BEFORE MOVING HORIZONTAL STABILIZER, MAKE CERTAIN THAT AREAS AROUND
HORIZONTAL STABILIZER AND ELEVATORS ARE CLEAR OF PERSONNEL AND
EQUIPMENT AND THAT UPPER TAIL CONE DOORS ARE CLOSED. THE MOVEMENT
OF SURFACES CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO
EQUIPMENT.
8. Remove the stabilizer trim lock assembly, F71336-501, from the stabilizer trim wheel.
9. Set the stabilizer trim cutout switches to NORMAL.
10. Remove the DO-NOT-CLOSE tags and close the following circuit breakers.
a. P6 Circuit Breaker Panel:
(1) STABILIZER TRIM ACTUATOR.
(2) STABILIZER TRIM CONT.
b. P18 Circuit Breaker Panel:
(1) AUTOPILOT STABILIZER TRIM SERVO.
11. Pressurize the elevator hydraulics. Refer to 737-300/400/500 AMM 27-31-00 as an accepted
procedure.
12. Pressurize the rudder hydraulics. Refer to 737-300/400/500 AMM 27-21-00 as an accepted
procedure.
13. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
43 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 44

Group 1, Configuration 2:
WARNING: BEFORE MOVING HORIZONTAL STABILIZER, MAKE CERTAIN THAT AREAS AROUND
HORIZONTAL STABILIZER AND ELEVATORS ARE CLEAR OF PERSONNEL AND
EQUIPMENT AND THAT UPPER TAIL CONE DOORS ARE CLOSED. THE MOVEMENT
OF SURFACES CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO
EQUIPMENT.
WARNING: DEPRESSURIZE THE RUDDER, ELEVATORS, AND HORIZONTAL STABILIZER.
PRESSURE IN THESE HYDRAULIC SYSTEMS CAN ALLOW COMPONENTS TO BE
MOVED SUDDENLY BY ANOTHER PERSON. THIS CAN CAUSE INJURIES TO
PERSONS AND DAMAGE TO THE EQUIPMENT.
1. Remove the pressure from systems A and B for the rudder. Refer to 737-300/400/500 AMM
27-21-00 as an accepted procedure.
2. Remove the pressure from the elevators. Refer to 737-300/400/500 AMM 27-31-00 as an accepted
procedure.
3. Set the stabilizer trim cutout switches to CUTOUT.
4. Open the following circuit breakers and attach DO-NOT-CLOSE tags.
a. P6 Circuit Breaker Panel:
(1) STABILIZER TRIM ACTUATOR.
(2) STABILIZER TRIM CONT.
b. P18 Circuit Breaker Panel:
(1) AUTOPILOT STABILIZER TRIM SERVO.
5. Use the stabilizer trim wheel on the stabilizer trim wheel to set the horizontal stabilizer at zero
degrees (3 units of trim).
6. Install the trim lock assembly, F71336-501, on the stabilizer trim wheel.
a. Turn the trim wheel to put the handle at the top of the wheel.
b. Adjust the height of the trim lock to set the trim wheel handle tightly in the bottom of the yoke.
c. Install the pin through the yoke and install the safety pin.
7. Do PART 9: POST-REPAIR INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN
for any crack and for any loose or any missing fastener.
NOTE: Prior to the release date of SB 737-55-1059 Revision 1, if a Boeing ODA FAA Form
8100-9 approved skin splice repair was installed, and the splice and replaced segment
of skin is in the same location as the part 4, part 5, part 6, or part 7 skin splice repair
given in paragraph 3.B., Work Instructions of this service bulletin, then the corresponding
paragraph 3.A., General Information note regarding inspection termination applies.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
44 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 45

NOTE: Doublers installed with solid rivets do not need to be inspected for any loose or any
missing fasteners.
a. CONDITION 7: NO CRACK AND NO LOOSE OR MISSING FASTENER FOUND IN ZONE-A
or ZONE-B or ZONE-C or ZONE-D or ZONE-E or ZONE-F.
(1) Repeat PART 9: POST-REPAIR INSPECTION OF THE HORIZONTAL STABILIZER
LOWER SKIN for any crack and for any loose or any missing fastener.
NOTE: Doublers installed with solid rivets do not need to be inspected for any loose or
any missing fasteners.
b. CONDITION 8: ANY CRACK FOUND IN ZONE-A.
(1) Do PART 4: SKIN SPLICE REPAIR IN ZONE-A.
c. CONDITION 9: ANY CRACK FOUND IN ZONE-B.
(1) Do PART 5: SKIN SPLICE REPAIR IN ZONE-B.
d. CONDITION 10: ANY CRACK FOUND IN ZONE-C.
(1) Do PART 6: SKIN SPLICE REPAIR IN ZONE-C.
e. CONDITION 11: ANY CRACK FOUND IN ZONE-D.
(1) Do PART 7: SKIN SPLICE REPAIR IN ZONE-D.
f. CONDITION 12: ANY CRACK FOUND IN ZONE-E OR ZONE-F.
(1) Contact The Boeing Company for repair instructions and do the repair.
g. CONDITION 13: ANY LOOSE OR ANY MISSING FASTENER FOUND, NO CRACK FOUND
IN ZONE-A OR ZONE-B OR ZONE-C OR ZONE-D.
(1) Do PART 10: OPEN HOLE INSPECTION for any corrosion and any hole elongation and
for any crack.
(a) CONDITION 14: NO CORROSION, NO HOLE ELONGATION AND NO CRACK
FOUND IN ANY HOLE OF LOOSE OR MISSING FASTENERS IN REPAIRED
AREAS.
1) CONDITION 14 (ACTION 1): Install new fastener.
NOTE: For repairs installed in accordance with an SRM, install new fastener
in accordance with 737-300 SRM 55-10-01, Repair 13 or 737-400 SRM
55-10-01, Repair 13 or 737-500 SRM 55-10-01, Repair 13. For repairs
installed in accordance with FIGURE 4 of this service bulletin, install
new fastener in accordance with FIGURE 4 of this service bulletin. Only
non-solid rivet repairs are being inspected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
45 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 46

2) CONDITION 14 (ACTION 2): Repeat PART 9: POST-REPAIR INSPECTION
OF THE HORIZONTAL STABILIZER LOWER SKIN for any crack and for any
loose or any missing fastener.
NOTE: Doublers installed with solid rivets do not need to be inspected for any
loose or any missing fasteners.
(b) CONDITION 15: ANY CORROSION OR ANY HOLE ELONGATION OR ANY CRACK
FOUND IN ANY HOLE OF LOOSE OR MISSING FASTENERS IN REPAIRED
AREAS.
1) CONDITION 15 (ACTION 1): Contact The Boeing Company for repair instructions
and do the repair.
2) CONDITION 15 (ACTION 2): Repeat PART 9: POST-REPAIR INSPECTION
OF THE HORIZONTAL STABILIZER LOWER SKIN for any crack and for any
loose or any missing fastener.
NOTE: Doublers installed with solid rivets do not need to be inspected for any
loose or any missing fasteners.
WARNING: BEFORE MOVING HORIZONTAL STABILIZER, MAKE CERTAIN THAT AREAS AROUND
HORIZONTAL STABILIZER AND ELEVATORS ARE CLEAR OF PERSONNEL AND
EQUIPMENT AND THAT UPPER TAIL CONE DOORS ARE CLOSED. THE MOVEMENT
OF SURFACES CAN CAUSE INJURIES TO PERSONNEL AND DAMAGE TO
EQUIPMENT.
8. Remove the stabilizer trim lock assembly, F71336-501, from the stabilizer trim wheel.
9. Set the stabilizer trim cutout switches to NORMAL.
10. Remove the DO-NOT-CLOSE tags and close the following circuit breakers.
a. P6 Circuit Breaker Panel:
(1) STABILIZER TRIM ACTUATOR.
(2) STABILIZER TRIM CONT.
b. P18 Circuit Breaker Panel:
(1) AUTOPILOT STABILIZER TRIM SERVO.
11. Pressurize the elevator hydraulics. Refer to 737-300/400/500 AMM 27-31-00 as an accepted
procedure.
12. Pressurize the rudder hydraulics. Refer to 737-300/400/500 AMM 27-21-00 as an accepted
procedure.
13. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
46 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 47

Group 1, Configuration 1:
PART 1: DETAILED INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN
1. Do a Detailed Inspection (DI) of the inspar lower skin of the horizontal stabilizer between SSTA
83.50 and 249.10 for any crack in accordance with the figures below.
Right Horizontal StabilizerLeft Horizontal Stabilizer
FIGURE 2FIGURE 1
Group 1, Configuration 1:
PART 2: PREVENTIVE MODIFICATION IN ZONE-A
1. Do one of the following:
a. OPTION 1: Remove the horizontal stabilizer and put it on a cradle. Refer to 737-300/400/500
AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX C.
NOTE: If PART 2: PREVENTIVE MODIFICATION IN ZONE-A is being done at the same time
as PART 6: SKIN SPLICE REPAIR IN ZONE-C or PART 7: SKIN SPLICE REPAIR IN
ZONE -D, do OPTION 1. If no other work is being done on the horizontal stabilizer, do
OPTION 1 or OPTION 2.
2. Make bonded skin assembly 692A5001-41 in accordance with Boeing drawing 692A5001.
3. Install made bonded skin assembly in accordance with Boeing drawing 692A5001-1.
4. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
5. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX D.
6. Put the airplane back to a serviceable condition.
Group 1, Configuration 1:
PART 3: PREVENTIVE MODIFICATION IN ZONE-B
1. Do one of the following:
a. OPTION 1: Remove the horizontal stabilizer and put it on a cradle. Refer to 737-300/400/500
AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX C.
NOTE: If PART 3: PREVENTIVE MODIFICATION IN ZONE-B is being done at the same time
as PART 6: SKIN SPLICE REPAIR IN ZONE-C or PART 7: SKIN SPLICE REPAIR IN
ZONE -D, do OPTION 1. If no other work is being done on the horizontal stabilizer, do
OPTION 1 or OPTION 2.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
47 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 48

2. Make bonded skin assembly 692A5001-42 in accordance with Boeing drawing 692A5001.
3. Install made bonded skin assembly in accordance with Boeing drawing 692A5001-2.
4. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
5. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX D.
6. Put the airplane back to a serviceable condition.
PART 4: SKIN SPLICE REPAIR IN ZONE-A
1. Do one of the following:
a. OPTION 1: Remove the left side horizontal stabilizer and put it on a cradle. Refer to
737-300/400/500 AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX C.
CAUTION: DO NOT CUT INTO THE STRUCTURE BEHIND THE SKIN. USE CAUTION TO
PREVENT NICKS, GOUGES OR OTHER DAMAGE TO THE STRUCTURE. IF THE
STRUCTURE IS DAMAGED, MORE REPAIR WORK WILL BE NECESSARY.
2. Remove, make and install the made lower skin in accordance with Boeing drawing 692A5001-1.
3. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
4. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX D.
5. Put the airplane back to a serviceable condition.
PART 5: SKIN SPLICE REPAIR IN ZONE-B
1. Do one of the following:
a. OPTION 1: Remove the right side horizontal stabilizer and put it on a cradle. Refer to
737-300/400/500 AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX C.
CAUTION: DO NOT CUT INTO THE STRUCTURE BEHIND THE SKIN. USE CAUTION TO
PREVENT NICKS, GOUGES OR OTHER DAMAGE TO THE STRUCTURE. IF THE
STRUCTURE IS DAMAGED, MORE REPAIR WORK WILL BE NECESSARY.
2. Remove, make and install the made lower skin in accordance with Boeing drawing 692A5001-2.
3. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
48 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 49

4. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX D.
5. Put the airplane back to a serviceable condition.
PART 6: SKIN SPLICE REPAIR IN ZONE-C
1. Do one of the following:
a. OPTION 1: Remove the left side horizontal stabilizer and put it on a cradle. Refer to
737-300/400/500 AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX E.
CAUTION: DO NOT CUT INTO THE STRUCTURE BEHIND THE SKIN. USE CAUTION TO
PREVENT NICKS, GOUGES OR OTHER DAMAGE TO THE STRUCTURE. IF THE
STRUCTURE IS DAMAGED, MORE REPAIR WORK WILL BE NECESSARY.
2. Remove, make and install the made lower skin in accordance with Boeing drawing 692A5001-3.
3. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
4. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX F.
5. Put the airplane back to a serviceable condition.
PART 7: SKIN SPLICE REPAIR IN ZONE-D
1. Do one of the following:
a. OPTION 1: Remove the right side horizontal stabilizer and put it on a cradle. Refer to
737-300/400/500 AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX E.
CAUTION: DO NOT CUT INTO THE STRUCTURE BEHIND THE SKIN. USE CAUTION TO
PREVENT NICKS, GOUGES OR OTHER DAMAGE TO THE STRUCTURE. IF THE
STRUCTURE IS DAMAGED, MORE REPAIR WORK WILL BE NECESSARY.
2. Remove, make and install the made lower skin in accordance with Boeing drawing 692A5001-4.
3. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
4. If the airplane was jacked and shored, remove shoring supports and jacks in accordance with
APPENDIX F.
5. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
49 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 50

Group 1, Configuration 1:
PART 8: EXTERNAL DOUBLER REPAIR
CAUTION: THE WEIGHT OF THE HORIZONTAL STABILIZER PRE-LOADS THE LOWER SKIN
RESULTING IN DEFLECTION OF THE SKIN SURFACE. OPTION 1: REMOVAL OF
THE HORIZONTAL STABILIZER IS THE PREFERRED METHOD FOR THIS REPAIR.
1. Do one of the following:
a. OPTION 1: Remove the horizontal stabilizer and put it on a cradle. Refer to 737-300/400/500
AMM 27-41-11 as an accepted procedure.
b. OPTION 2: Jack and shore the airplane in accordance with APPENDIX C.
CAUTION: DO NOT NOTCH OR DRILL THROUGH THE REAR SPAR CHORD OR ADJACENT
STRUCTURE WHEN THE DAMAGED SKIN IS CUT OUT OR STOP DRILLED.
2. Do one of the following:
a. If the crack is further than 0.50 inch from the centerline of fastener(s), stop drill the crack in
accordance with FIGURE 3.
b. If the crack is 0.50 inch or closer from the centerline of fastener(s), cut out the damaged area
in accordance with FIGURE 9.
3. Install an external doubler in accordance with FIGURE 4. The repair is similar to 737-300 SRM
55-10-01 Repair 13, 737-400 SRM 55-10-01 Repair 13, 737-500 SRM 55-10-01 Repair 13.
4. If removed, install horizontal stabilizer. Refer to 737-300/400/500 AMM 27-41-11 as an accepted
procedure.
5. If the airplane was jacked and shored, remove shoring and jacks in accordance with APPENDIX
D.
6. Put the airplane back to a serviceable condition.
Group 1, Configuration 2:
PART 9: POST-REPAIR INSPECTION OF THE HORIZONTAL STABILIZER LOWER SKIN
1. Do a High Frequency Eddy Current (HFEC) inspection of the skin around any SRM repair or any
external doubler repair for any crack and a Detailed Inspection of repaired doublers for any loose
or any missing fastener in accordance with FIGURE 5.
NOTE: Doublers installed with solid rivets do not need to be inspected for any loose or any
missing fastener.
2. Do a Detailed Inspection of the inspar lower skin of the horizontal stabilizer in unrepaired areas
for any crack in accordance with the figures below:
Right Horizontal StabilizerLeft Horizontal Stabilizer
FIGURE 7FIGURE 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
50 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 51

3. Do a Low Frequency Eddy Current (LFEC) inspection of the forward fastener row of any external
doubler repair for any crack in accordance with FIGURE 8.
Group 1, Configuration 2:
PART 10: OPEN HOLE INSPECTION
1. Remove any loose fastener.
2. Do a Detailed Inspection of open holes for any corrosion.
3. Do a Detailed Inspection of open holes for any hole elongation.
4. Do a High Frequency Eddy Current (HFEC) inspection of open holes in accordance with 737 NDT
Manual Part 6, 51-00-00 Procedure 11 or Procedure 16 for any crack.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1: April 06, 2016
51 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-55-1059
This Figure applies only to: Group 1, Configuration 1.
SSTA
249.10
SSTA
180.00
SSTA
105.70  SSTA
83.50
ZONE-E
_REAR SPAR
ZONE-C
ZONE-A  AREA SUBJECT TO  DETAILED
INSPECTION  INSPECTION AREA
FWD '
AREA OF INSPECTION
0.30
TYPICAL CRACK
• SPAR CHORD
•
LOWER INSPAR SKIN  € REAR SPAR
0.1  • & FASTENERS
1.50
> INBD
CHEM-MIL PERIPHERY
FWD
S45379
FIGURE 1: LEFT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: September 10, 1998
Revision 1 April 06, 2016  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-55-1059
Work - See page 1 for details.  52 of 85

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTESREFERENCESPROCEDURENAMETASKSTEP
(a) (b)-Detailed Inspec-
tion
Lower surface skinInspect1
(a) Do a Detailed Inspection for any crack.
(b) As an option to the Detailed Inspection, do a High Frequency Eddy Current (HFEC) inspection in ac-
cordance with 737 NDT Manual Part 6, 51-00-00, Procedure 23, and one of the following: (i) a Medium
Frequency Eddy Current (MFEC) inspection in accordance with 737 NDT Manual Part 6, 53-30-23;
(ii) a C-Scan inspection in accordance with 737 NDT Manual Part 6, 53-30-25 using reference standard
NDT1097-B; (iii) a Magneto Optical Imaging (MOI) inspection in accordance with 737 NDT Manual
Part 6, 55-10-08 for any crack.
FIGURE 1: LEFT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1 April 06, 2016
53 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 54 (OCR)

BOEING SERVICE BULLETIN 737-55-1059
This Figure applies only to: Group 1, Configuration 1.
SSTA
249.10
SSTA
180.00
SSTA
SSTA  105.70
83.50
ZONE-F
REAR  ZONE-D
SPAR
ZONE-B
1 DETAILED
• INSPECTION AREA
AREA SUBJECT
TO INSPECTION
AREA OF INSPECTION
0.30
TYPICAL CRACK
• SPAR CHORD
LOWER INSPAR SKIN  E REAR SPAR
0.1  * € FASTENERS
1.50
INBD <
Л  CHEM-MIL PERIPHERY
FWD
2442042
FIGURE 2: RIGHT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION
(SHEET 1 OF 2)
Original Issue: September 10, 1998
Revision 1 April 06, 2016  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  737-55-1059
Work - See page 1 for details.  54 of 85

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
More DataQtyIdentificationNameTaskStep
(a) (b)--Lower surface skinInspect1
(a) Do a Detailed Inspection of the outer surface for any crack. The inspection area is from 0.30 inch radius
from the center of each fastener and from 0.10 inch from the centerline of the forward fastener row to
1.50 inch forward of the forward fastener row centerline of the rear spar-to-skin fasteners.
(b) As an option to the Detailed Inspection, do a High Frequency Eddy Current (HFEC) inspection in accor-
dance with 737 NDT Manual Part 6, 51-00-00, Procedure 23, and one of the following: (i) a Medium Fre-
quency Eddy Current (MFEC) inspection in accordance with 737 NDT Manual Part 6, 53-30-23; (ii) a C-
Scan inspection in accordance with 737 NDT Manual Part 6, 53-30-25 using reference standard NDT1097-
B; (iii) a Magneto Optical Imaging (MOI) inspection in accordance with 737 NDT Manual Part 6, 55-10-08
for any crack.
FIGURE 2: RIGHT HORIZONTAL STABILIZER LOWER SKIN - DETAILED INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1 April 06, 2016
55 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 56

This Figure applies only to: Group 1, Configuration 1.
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
NOTESQTYPART NUMBERNAMETASKSTEP
(a) (b)--DamageDrill1
(a) Do not drill through the rear spar chord or adjacent structure. Use a 0.020 inch thick corrosion resistant
steel sacrificial sheet to prevent damage.
(b) Stop drill the crack with 0.25 inch diameter holes. Refer to 737-300 SRM 51-10-02 or 737-400 SRM 51-
10-02 or 737-500 SRM 51-10-02 as an accepted procedure.
FIGURE 3: STOP DRILL REPAIR
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1 April 06, 2016
56 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 57 (OCR)

BOEING SERVICE BULLETIN 737-55-1059
This Figure applies only to: Group 1, Configuration 1.
TYPICAL  0.50R
1.02 TYPICAL  SPACING THIS  ROW  SSTA  166.3
0.55  0.94 TYPICAL  SPACING THIS  ROW  LEFT SIDE LOWER STABILIZER SURFACE SHOWN, RIGHT SIDE OPPOSITE
0.99 TYPICAL  SPACING THIS  ½1197 7  SSTA  157.1
ROW
0.94  TYPICAL  0.94  TYPICAL  TYPICAL  CHEM-MILL  EDGE
- SEE A  ½ 4 4 ½  14648147  SSTA  147.9  TAINBD
LOWER CHORD  (TYPICAL)  FWD
TAPERED  SHIM  (TYPICAL)
TAPERED  SHIM  (TYPICAL›
FIGURE 4: EXTERNAL DOUBLER REPAIR INSTALLATION
(SHEET 1 OF 4)
Original Issue: September 10, 1998
Revision 1 April 06, 2016  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-55-1059
Work - See page 1 for details.  57 of 85

### Page 58 (OCR)

BOEING SERVICE BULLETIN 737-55-1059
SSTA  138.7  & FASTENER  EDGE MARGIN  2D  + 0.05
SKIN
2T  0.01  0.02  TYPICAL  A-A
SSTA  SSTA  129.5  120.37  LEFT SIDE LOWER STABILIZER SURFACE SHOWN, RIGHT SIDE OPPOSITE
TAPERED  SHIM  (TYPICAL)  LOWER  CHORD  (TYPICAL)  INBD
FWD
S46176
FIGURE 4: EXTERNAL DOUBLER REPAIR INSTALLATION
(SHEET 2 OF 4)
Original Issue: September 10, 1998
Revision 1 April 06, 2016  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-55-1059
Work - See page 1 for details.  58 of 85

### Page 59

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one repair.
NOTESQTYPART NUMBERNAMETASKSTEP
Remove carefully to reduce the
need for oversize replacement
fasteners.
--FastenersRemove1
Make from 0.080 inch 2024-T3
clad aluminum sheet.
--DoublerMake2
Chamfer all four edges. See View
A-A.
--EdgesChamfer3
Maximum gap between parts be-
fore fastener installation is 0.010
inch.
--DoublerClamp4
Match drill using a template and,
where access is possible, back-
drill using existing fastener holes.
--HolesDrill5
Mark new fastener holes.--HolesMark6
---HolesDrill
Refer to 737-300 SRM 51-20-01
or 737-400 SRM 51-20-01 or 737-
500 SRM 51-20-01 as an accept-
ed procedure.
-AlodineChemical Conversion
Coating Solution
Apply7
-BMS 10-11, Type IPrimer
Color to match adjacent structure.-BMS 10-11, Type IIEnamel
Fay seal and install fasteners wet
using BMS 5-95.
--DoublerInstall8
Around edges of doubler, BMS
5-95.
--Fillet SealApply9
CAUTION: Make sure the distance from the fastener to the edge of the chem-mill is 0.375 inch.
FIGURE 4: EXTERNAL DOUBLER REPAIR INSTALLATION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1 April 06, 2016
59 of 85
BOEING SERVICE BULLETIN 737-55-1059

### Page 60

The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener.
NOTESHOLE DIAPART NUMBERNAMECODE
(a)0.190 - 0.198NAS1399D6AB( )RivetA
(b)66-2955-11Countersink Washer
(a)0.159 - 0.167NAS1399D5AB( )RivetB
(b) (c)66-2955-47Countersink Washer
Install bolt with BMS 5-95. Use
0.0156 inch oversized fasteners if
necessary.
0.1953 - 0.1960BACB30NW6K( )BoltC
(b)66-2955-11Countersink Washer
-BACC30M6Collar
(a) If desired, you can install access panels in the lower skin. Refer to 737-300 SRM 55-10-01, Figure
201, or 737-400 SRM 55-10-01, Figure 201, or 737-500 SRM 55-10-01, Figure 201 as an accepted
procedure. Install blind rivets wet with sealant BMS 5-95.
(b) Refer to 737-300 SRM 51-40-08 or 737-400 SRM 51-40-08 or 737-500 SRM 51-40-08 as an accepted
procedure.
(c) NAS1399D5A2 rivets are installed without washers.
FIGURE 4: EXTERNAL DOUBLER REPAIR INSTALLATION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: September 10, 1998
737-55-1059Revision 1 April 06, 2016
60 of 85
BOEING SERVICE BULLETIN 737-55-1059

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-55-1059/file/1c811fb55d2e.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
