# Boeing Special Attention Service Bulletin 737-57-1293: Boeing - Service Bulletin

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2009-0288; AD 2013-08-18 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 737-57-1293](https://openairdocs.org/service-documents/boeing/sb-737-57-1293.md)
- Title as filed: Boeing - Service Bulletin
- Pages: 135
- PDF: https://openairdocs.org/files/sha256/ec/ea/eceae11611dab8cfc603fb3e46a3c79917535e389c7bebd052d671a32f6d6033
- Page: https://openairdocs.org/service-documents/boeing/sb-737-57-1293/file/eceae11611da

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-57-1293
Original Issue: November 13, 2008
Revision 3: December 14, 2012
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2008 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner™,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and Boeing
liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection
with this document unless provided in writing by Boeing. BOEING is a trademark of Boeing Management
Company.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
1 of 135
5.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
2 of 135
BOEING SERVICE BULLETIN 737-57-1293
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 2 8
B. Concurrent Requirements ...................................... 2 8
C. Reason ................................................ 2 8
D. Description .............................................. 2 9
E. Compliance .............................................. 3 0
F. Approval ............................................... 3 0
G. Manpower .............................................. 3 1
H. Weight and Balance Changes .................................... 3 3
I. Electrical Load Data ......................................... 3 4
J. References .............................................. 3 4
1. Existing Data: ......................................... 3 4
2. Data Supplied with this Service Bulletin: ........................... 3 4
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 3 4
K. Publications Affected ........................................ 3 5
L. Interchangeability and Intermixability of Parts ........................... 3 5
M. Software Accomplishment Summary ................................ 3 5
2. MATERIAL INFORMATION ........................................ 3 7
A. Material - Price and Availability ................................... 3 7
B. Industry Support Information .................................... 3 8
C. Parts Necessary for Each Airplane ................................. 3 8
1. Kits/Parts: ........................................... 3 8
2. Parts and Materials Supplied by the Operator: ........................ 3 9
3. Parts Modified and Reidentified: ............................... 4 1
4. Parts Removed and Not Replaced: .............................. 4 3
D. Parts Necessary to Change Spares ................................. 4 3
E. Special Tooling - Price and Availability ............................... 4 3
F. Special Tooling Necessary to do this Service Bulletin ....................... 4 3
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 4 5
A. GENERAL INFORMATION ..................................... 4 5
B. WORK INSTRUCTIONS ....................................... 4 6
FIGURE 1: LEFT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS [Group 1, Configuration 1] . 52
FIGURE 2: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS
[Group 2, Configuration 1] ................................... 5 4
FIGURE 3: LEFT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE
BLOWOUT DOOR HINGE [Group 2, Configuration 1] .................... 5 6
FIGURE 4: LEFT WING - BLOWOUT DOOR HINGE TRIM [Group 1-2, Configuration 1] ........ 5 9
FIGURE 5: LEFT WING - OUTBOARD STRAKELET BOX - MODIFICATION [Group 1, Configuration 1]
.................................................. 6 2
FIGURE 6: LEFT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL REPLACEMENT [Group 1,
Configuration 1] ......................................... 6 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
3 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 4

FIGURE 7: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT
APPLICATION [Group 1, Configuration 1] .......................... 7 3
FIGURE 8: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT
APPLICATION [Group 2, Configuration 1] .......................... 7 8
FIGURE 9: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - LEAK TEST
[Group 1-2] ........................................... 8 2
FIGURE 10: LEFT WING - LEADING EDGE SLAT TRACK RIBS - SEALANT APPLICATION [Group 1,
Configuration 1] ......................................... 8 4
FIGURE 11: LEFT WING - LEADING EDGE SLAT TRACK RIBS - CLOSE ACCESS [Group 1, Configuration
1 ]  ................................................ 8 7
FIGURE 12: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - CLOSE
ACCESS [Group 2, Configuration 1] .............................. 8 9
FIGURE 13: RIGHT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS [Group 1, Configuration 1]
.................................................. 9 1
FIGURE 14: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS
[Group 2, Configuration 1] ................................... 9 3
FIGURE 15: RIGHT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE
BLOWOUT DOOR HINGE [Group 2, Configuration 1] .................... 9 5
FIGURE 16: RIGHT WING - BLOWOUT DOOR HINGE TRIM [Group 1-2, Configuration 1] ....... 9 8
FIGURE 17: RIGHT WING - OUTBOARD STRAKELET BOX - MODIFICATION [Group 1, Configuration 1]
................................................. 1 0 1
FIGURE 18: RIGHT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL REPLACEMENT [Group 1,
Configuration 1] ........................................ 1 0 7
FIGURE 19: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT
APPLICATION [Group 1, Configuration 1] .......................... 1 1 2
FIGURE 20: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - SEALANT
APPLICATION [Group 2, Configuration 1] .......................... 1 1 7
FIGURE 21: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - LEAK
TEST [Group 1-2] ....................................... 1 2 1
FIGURE 22: RIGHT WING - LEADING EDGE SLAT TRACK RIBS - SEALANT APPLICATION [Group 1,
Configuration 1] ........................................ 1 2 3
FIGURE 23: RIGHT WING - LEADING EDGE SLAT TRACK RIBS - CLOSE ACCESS [Group 1, Configuration
1 ]  ................................................ 1 2 6
FIGURE 24: RIGHT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - CLOSE
ACCESS [Group 2, Configuration 1] ............................. 1 2 8
FIGURE 25: LEFT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL DISK INSTALLATION . 130
FIGURE 26: RIGHT WING - FUEL SHUTOFF VALVE ACCESS DOOR - SEAL DISK INSTALLATION . 133
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
4 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 5

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 737-57-1293Original Issue: November 13, 2008
Revision 3: December 14, 2012
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on the airplane(s) changed in accordance with Revision 2 of this service bulletin.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2008-NM-214-AD, is related to
this service bulletin.
REASON FOR REVISION
This revision is sent to clarify the requirements for the reidentification of parts and assemblies changed by this
service bulletin.
The data given in Information Notice 737-57-1293 IN 04 and 737-57-1293 IN 05 are included in this revision.
These sections were changed:
1. Added Paragraph 1.M., Software Accomplishment Summary.
2. Paragraph 2.B., Industry Support Information, changed warranty statement.
3. Paragraph 2.C.1., Parts Necessary for Each Airplane, added new footnote and changed group
applicability heading.
4. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added new footnotes.
5. Paragraph 2.C.3., Parts Modified and Reidentified, updated list of parts.
6. Paragraph 2.D., Parts Necessary to Change Spares, added seal retainer.
7. Paragraph 3.B., Work Instructions, reorganized existing work instructions into group-configuration sets
and changed applicable references.
8. Figures 4 and 16, changed part numbers and footnote.
9. Figures 5 and 17, added optional part number, changed part numbers and footnotes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
5 of 135

### Page 6

10. Figures 6 and 18, changed part numbers.
11. Figure 11, changed part number.
12. Figures 25 and 26, added button callout on art, changed quantity and footnotes.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
November 13, 2008Original Issue:
January 11, 2010Revision 1:
September 28, 2011Revision 2:
December 14, 2012Revision 3:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
6 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 7

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 737-57-1293Original Issue: November 13, 2008
Revision 3: December 14, 2012
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions to modify the fluid drain path in the wing leading edge area, forward of
the wing front spar. If this service bulletin is not incorporated, flammable fluids accumulating in the wing leading
edge may drain inboard and onto the engine exhaust nozzle, which could result in a fire.
Boeing has received a report of leaking fuel from the wing leading edge area at the inboard end of the number
5 leading edge slat. The leak was discovered during a post flight inspection on a 737 airplane with a fuel quantity
of over 2500 pounds. Subsequent investigation found that the leak occurred in an area of the front spar that
does not have a proper drain path. This led to the fuel draining onto the engine exhaust nozzle. The leak appears
to have been caused by loose downstop assembly hardware of the slat track down stop and is the subject of
Boeing Service Letter 737-SL-57-084.
Group 2 airplanes had the wing leading edge drain path incorporated in production, however the parting agent
and Formed-In- Place gasket on the blowout door and fuel shutoff valve access door needs to be replaced and
the new seal disks need to be installed on the latches in the fuel shutoff valve access door. Group 3 airplanes
had the wing leading edge drain path incorporated in production and had the blowout doors and fuel shutoff
valve access doors sealed properly in production, but they need the new seal disks installed on the latches in
the fuel shutoff valve access doors.
Boeing Service Related Problem (SRP) 737NG-SRP-28-0110 and 737NG-SRP-57-0248 are related to this
service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
7 of 135

### Page 8

ReferenceAffectedPlanning Data
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION (PRR 38275-181S, PRR 38275-113S)
Group 1, Configuration 1:
1. Open the blowout door and the fuel shutoff valve access door. Remove and keep 13 wing lower leading
edge panels from slat station (SS) 26 to slat station (SS) 500 in the left and right wings. Remove wing
upper leading edge panels, if necessary, to help install the flame arrestor tube.
2. Apply sealant to the cavities between the inboard slat track ribs and leading edge lower panels at SS
47.69, 122.69, 163.95, 240.95, 282.91, 362.51 and 409.09 in the left and right wings.
3. At the outboard leading edge strakelet box, install a flame arrestor tube through the vapor barrier rib
to direct fluids to the strut drain system. Apply sealant to create a form-in-place gasket at the blowout
door located under the strakelet box to prevent fluids from leaking onto the engine exhaust nozzle.
Replace the existing seal in the fuel shut off valve access door with a bulb seal to prevent flammable
fluid leakage onto the engine exhaust nozzle.
4. Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel
shutoff valve access doors.
5. Close the fuel shutoff valve access door and the blowout door and do a leak test. Install all lower leading
edge access panels, and any upper leading edge panels that may have been removed.
Group 2, Configuration 1:
1. Open the blowout door and the fuel shutoff valve access door in the left and right wings. Remove and
keep the lower leading edge access panel immediately outboard of the fuel shutoff valve access door
in the left and right wings. Remove the parting agent and sealant at these locations and install new
sealant using improved parting agent.
2. Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel
shutoff valve access doors.
3. Close the blowout door and fuel shutoff valve access door and do a leak test. Install the lower leading
edge access panel.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
8 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 9

Group 1-2, Configuration 2; Group 3:
1. Install a rubber seal disk under the head of the smaller latch button at each latch location on the fuel
shutoff valve access doors.
EFFECTIVITY
737-600, -700, -700C, -800, -900, -900ER airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected
airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2008-NM-214-AD, is related to
this service bulletin.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of April 28, 2006. Please refer to Paragraph
2.B., Industry Support Information.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
9 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 10 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
INSTALL A FLAME ARRESTOR TUBE THROUGH THE
VAPOR BARRIER RIB. APPLY SEALANT TO THE BLOW OUT
DOOR, REPLACE THE SEAL IN THE FUEL SHUT OFF
ACCESS PANEL, AND INSTALL SEAL DISK.
SEE
00000000000
SEE  0...
UPPER SKIN
PANEL
INBOARD RIB
ASSEMBLY
APPLY SEALANT
BETWEEN ACCESS PANELS  FRONT
AND INBOARD SLAT  SPAR
TRACK RIB ASSEMBLY
UPPER SKIN
PANEL  INBD
FILL MACHINE GAP ON  FUDI
INBOARD RIB ASSEMBLY
WITH SEALANT
DRAIN PATH
OUTBOARD RIB
ASSEMBLY CONLY BASE  1343463
SHOWN FOR CLARITY)
Original Issue: November 13, 2008
Revision 3: December 14, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57-1293
Work - See page 1 for detalls.  10 of 135

### Page 11

Commercial 
Airplanes
737
Service Bulletin
SPECIAL ATTENTION
Number: 737-57-1293
Original Issue: November 13, 2008
Revision 3: December 14, 2012
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Fuel Drain Path Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-19567 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below. An equivalent change is on subsequent
production airplanes. Refer to PRR 38275-113S and PRR 38275-181S for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
737-600, -700, -700C, -800 and -900 airplanes Line Numbers 1 -
1980, 1982 - 2092 and 2094 - 2130.
-1
Airplanes that have not incorporated the original issue or Revision 1
of the bulletin.
1
Airplanes that have incorporated the original issue or Revision 1 of
the bulletin.
2
737-700, -700C, -800 and -900ER airplanes Line Numbers 2131 -
2437 delivered with a modified fuel drain path in the wing leading
edge.
-2
Airplanes that have not incorporated the original issue or Revision 1
of the bulletin.
1
Airplanes that have incorporated the original issue or Revision 1 of
the bulletin.
2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
11 of 135

### Page 12

DESCRIPTIONCONFIGURATIONGROUP
737-700, -700C, -800 and -900ER airplanes Line Numbers 2438-3833
that have had the intent of Revision 1 of the bulletin incorporated in
production.
-3
Airplane Models:
737-600, 737-700, 737-700C, 737-800, 737-900, 737-900ER
GroupVariable Number
1YA001 - YA099
1YA101 - YA199
1YA201 - YA211
1YA221
1YA231 - YA242
1YA251 - YA256
1YA271 - YA272
1YA291
1YA301 - YA302
1YA311 - YA314
1YA321 - YA323
1YA336 - YA345
1YA351
1YA356 - YA357
1YA366 - YA367
1YA371 - YA377
1YA501 - YA536
1YA541 - YA552
1YA571 - YA578
1YA601 - YA615
1YA621 - YA622
1YA626 - YA631
1YA635 - YA636
1YA641 - YA642
1YA645 - YA650
1YA656 - YA659
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
12 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 13

GroupVariable Number
1YA666 - YA667
1YA671 - YA672
1YA681 - YA691
1YA701 - YA710
1YA721 - YA722
1YA731 - YA734
1YA751 - YA756
1YA801 - YA803
1YA809
1YA811 - YA814
1YA831 - YA835
1YA841 - YA862
1YA881 - YA882
1YA891 - YA892
1YA961 - YA978
1YB001 - YB006
1YB101 - YB132
1YB151 - YB153
1YB156 - YB158
1YB161 - YB164
1YB171 - YB172
1YB181 - YB184
1YB201 - YB208
1YB271
1YB276
1YB301 - YB310
1YB371 - YB392
1YB501 - YB502
1YB521 - YB526
1YB541 - YB544
1YB551
1YB561 - YB598
1YB601 - YB632
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
13 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 14

GroupVariable Number
3YB633 - YB635
1YB651
1YB656
2YB671 - YB672
1YB851 - YB863
1YB871 - YB874
1YB881 - YB891
2YB892 - YB893
1YB901 - YB903
1YB911
1YB961 - YB964
2YB965 - YB971
3YB972 - YB975
3YB981
3YB986 - YB998
1YC001 - YC030
1YC051 - YC083
2YC084
1YC091 - YC094
3YC095
1YC101 - YC104
1YC111 - YC113
1YC121
1YC126 - YC127
1YC136 - YC141
1YC146 - YC147
1YC151 - YC156
1YC166 - YC171
1YC176 - YC178
2YC179
1YC186 - YC189
2YC190
1YC201 - YC203
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
14 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 15

GroupVariable Number
1YC206 - YC207
1YC301 - YC305
1YC321 - YC387
1YC391 - YC394
1YC396
1YC401 - YC417
1YC421 - YC422
1YC426 - YC428
1YC436 - YC437
2YC438 - YC439
1YC441 - YC448
1YC451 - YC455
1YC459
1YC461 - YC467
1YC471 - YC499
1YC501 - YC526
1YC571 - YC583
1YC587 - YC589
1YC591 - YC593
1YC601 - YC655
1YC681 - YC696
1YC701 - YC715
1YC720 - YC725
1YC727 - YC746
2YC747 - YC749
3YC750
1YC751 - YC752
1YC761 - YC770
1YC781 - YC793
1YC801 - YC892
1YC901 - YC907
1YC921 - YC922
1YC931 - YC932
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
15 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 16

GroupVariable Number
1YC941 - YC951
1YC971 - YC978
1YC981 - YC983
1YD001 - YD007
1YD021 - YD025
1YD041 - YD057
1YD081 - YD084
1YD101 - YD110
3YD111 - YD117
1YD121 - YD126
1YD151 - YD159
1YD171 - YD172
1YD201 - YD203
1YD206 - YD209
1YD216 - YD219
1YD251 - YD254
1YD256 - YD257
1YD261
1YD301 - YD334
1YD391
1YD401 - YD410
1YD412 - YD414
3YD415 - YD417
1YD481 - YD485
1YD491 - YD495
2YD496 - YD499
1YD501 - YD512
1YD531 - YD535
1YD541 - YD547
1YD561 - YD564
1YD571 - YD572
1YD591 - YD595
1YD601 - YD612
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
16 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 17

GroupVariable Number
1YD651 - YD655
1YE001 - YE020
1YE051
1YE101 - YE109
1YE151 - YE157
1YE171 - YE172
1YE201 - YE206
1YE301 - YE305
1YE321 - YE326
1YE371 - YE383
3YF001 - YF011
3YF021 - YF049
3YF051 - YF067
3YF086 - YF087
3YF106 - YF107
3YF111 - YF114
3YF116 - YF119
3YF121 - YF131
3YF176 - YF178
3YF191 - YF192
3YF201 - YF276
3YF401 - YF402
3YF431 - YF432
3YF436 - YF437
3YF441 - YF442
3YF451 - YF460
3YF501 - YF599
3YF601 - YF633
3YF701 - YF707
3YF801 - YF805
3YF831 - YF832
3YF836 - YF838
3YF901 - YF905
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
17 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 18

GroupVariable Number
3YF921 - YF928
3YF951 - YF954
1YG001 - YG044
1YG061 - YG064
1YG066 - YG089
1YG091 - YG099
1YG101 - YG102
2YG103
3YG104
1YG111 - YG112
2YG113 - YG114
2YG116 - YG118
3YG119 - YG133
1YG201 - YG205
1YG211 - YG214
3YG221 - YG224
2YG251 - YG252
1YG501 - YG509
3YG510 - YG512
1YG601 - YG602
2YG701
3YG711
2YH003 - YH006
3YH007 - YH012
3YH031 - YH050
2YH051
3YH052 - YH055
3YH071 - YH080
3YH101 - YH132
3YH201 - YH202
3YH206 - YH207
3YH301 - YH306
3YH321 - YH322
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
18 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 19

GroupVariable Number
3YH501 - YH511
3YH551
3YH601 - YH602
3YH611 - YH612
3YH631
1YJ001 - YJ006
2YJ007 - YJ008
3YJ009 - YJ010
1YJ011 - YJ013
1YJ021
1YJ471 - YJ480
1YJ501 - YJ517
1YJ531 - YJ558
3YJ559 - YJ579
1YJ591 - YJ594
2YJ595 - YJ596
3YJ597 - YJ599
1YJ631 - YJ632
1YJ671 - YJ685
2YJ686 - YJ689
1YJ690 - YJ694
1YJ801 - YJ867
1YJ871
2YJ872 - YJ873
3YJ874 - YJ880
1YJ901 - YJ902
2YJ903
3YJ904
3YJ908 - YJ910
1YJ911 - YJ928
3YJ929
1YJ931 - YJ936
2YJ937
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
19 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 20

GroupVariable Number
1YJ941 - YJ949
2YJ950 - YJ955
3YJ956
3YJ961
2YJ976 - YJ977
1YK001 - YK007
1YK101 - YK104
1YK111 - YK112
1YK121 - YK122
1YK131 - YK132
3YK133
1YK136 - YK137
2YK138 - YK139
1YK141 - YK142
1YK146 - YK147
2YK148
1YK151 - YK154
1YK161 - YK162
2YK163 - YK166
3YK167
3YK171
3YK176 - YK177
3YK186
3YK191
3YK196
3YK201 - YK202
1YK301 - YK305
2YK306 - YK307
3YK308 - YK314
1YK321 - YK334
2YK335 - YK336
3YK337 - YK340
1YK361 - YK369
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
20 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 21

GroupVariable Number
2YK370 - YK372
3YK373 - YK378
1YK401 - YK406
1YK426 - YK427
1YK431 - YK443
2YK444 - YK450
1YK456 - YK460
3YK461 - YK467
3YK471 - YK473
1YK476
1YK480 - YK484
2YK485
3YK486 - YK487
3YK491 - YK492
3YK495 - YK498
1YK511 - YK514
2YK515
3YK516
3YK521 - YK530
1YK551 - YK565
3YK566 - YK570
1YK571
1YK576 - YK577
1YK580 - YK582
2YK583 - YK585
1YK601 - YK602
2YK606 - YK607
1YK611 - YK613
2YK614
3YK615 - YK616
1YK621 - YK623
2YK624 - YK625
3YK626 - YK630
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
21 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 22

GroupVariable Number
1YK631 - YK632
2YK633 - YK634
1YK641 - YK642
2YK643 - YK644
1YK651 - YK654
2YK655 - YK658
3YK659 - YK665
3YK671 - YK672
3YK676 - YK677
3YK681 - YK686
3YK691
1YK701 - YK707
2YK708 - YK709
3YK710 - YK713
2YK716 - YK719
1YK721 - YK731
2YK732 - YK741
3YK751 - YK770
3YK776 - YK778
3YK781 - YK785
1YK791 - YK792
2YK796 - YK797
1YK801 - YK830
2YK831 - YK863
3YK864 - YK899
1YK901 - YK906
2YK907 - YK910
3YK911 - YK912
2YK918
3YK919
2YK921
3YK922 - YK929
1YK941 - YK944
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
22 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 23

GroupVariable Number
2YK945 - YK950
3YK951 - YK960
1YK961 - YK964
2YK965 - YK970
3YK971 - YK980
1YK981 - YK982
2YK983 - YK984
3YK985 - YK998
1YL001 - YL005
1YL011 - YL014
2YL015 - YL016
2YL021 - YL024
1YL051 - YL052
2YL056 - YL057
2YL061
2YL066 - YL069
3YL076 - YL077
2YL101 - YL106
3YL107 - YL137
1YL201
2YL202 - YL203
3YL204 - YL230
3YL241 - YL242
1YL271
2YL272
2YL281 - YL282
3YL283 - YL284
1YL301 - YL302
2YL303
2YL311 - YL312
3YL313 - YL314
3YL316 - YL321
3YL351 - YL353
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
23 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 24

GroupVariable Number
3YL371 - YL374
3YL401
2YL421 - YL423
3YL424 - YL429
2YL431 - YL436
3YL437 - YL444
1YL461
2YL462 - YL470
3YL471 - YL478
2YL501 - YL503
3YL504 - YL509
2YL531
3YL532 - YL534
3YL541 - YL551
3YL561 - YL579
3YL591 - YL598
2YL601 - YL603
3YL604 - YL606
3YL611 - YL612
3YL616 - YL617
3YL621
3YL626
3YL631 - YL634
3YL636 - YL637
3YL661 - YL664
3YL676 - YL691
3YL696 - YL697
3YL701 - YL707
3YL731
3YL751 - YL752
3YL756 - YL757
3YL761 - YL780
3YL796 - YL797
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
24 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 25

GroupVariable Number
3YL801 - YL815
2YL901
3YL902 - YL910
3YL921 - YL930
2YL931
3YL932 - YL940
3YL951 - YL968
1YM101 - YM103
1YM201 - YM216
2YM217 - YM230
3YM231 - YM244
1YM251 - YM299
1YM301 - YM309
2YM310 - YM343
3YM344 - YM399
3YM401 - YM413
1YM471
1YM481 - YM484
1YM501 - YM511
2YM512 - YM514
3YM515
1YM521 - YM522
1YM541
1YM551 - YM553
1YM571 - YM572
2YM581 - YM582
1YM591 - YM593
3YM594 - YM599
1YM631 - YM633
2YM634
2YM641 - YM644
3YM645 - YM652
2YM671 - YM672
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
25 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 26

GroupVariable Number
3YM673 - YM674
3YM691 - YM699
3YM701 - YM710
3YM761 - YM765
3YM771 - YM779
1YN001 - YN008
2YN009 - YN013
3YN014 - YN016
1YN021
2YN022 - YN023
3YN024
1YN061
1YN071 - YN074
2YN075 - YN078
3YN079 - YN082
2YN091 - YN092
1YN101 - YN106
2YN107 - YN112
2YN121
2YN201
3YN202
2YN211 - YN214
3YN215 - YN219
2YN231
3YN232 - YN236
3YN261
3YN501
3YN531 - YN534
3YN551
3YN601
3YN701 - YN702
3YQ001 - YQ003
3YQ011 - YQ019
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
26 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 27

GroupVariable Number
3YQ026 - YQ029
3YQ036 - YQ044
3YQ201 - YQ202
3YQ231
3YQ241 - YQ251
3YQ281 - YQ282
3YQ291 - YQ296
3YQ301 - YQ302
3YQ401 - YQ403
3YQ451 - YQ454
3YR001 - YR013
3YR051 - YR056
3YR101 - YR102
3YR111 - YR116
3YR126 - YR129
3YR141 - YR142
3YR166 - YR172
3YR201 - YR204
3YR231 - YR245
3YR271 - YR278
3YR286
3YR291 - YR294
3YR296 - YR297
3YR301 - YR311
3YR361 - YR362
3YR381
3YR401 - YR405
3YR421 - YR422
3YR431
3YR451 - YR453
3YR501 - YR503
3YR511 - YR512
3YR516 - YR518
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
27 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 28

GroupVariable Number
3YR526
3YR601 - YR605
3YR616 - YR617
3YR651 - YR652
3YR656
3YR701 - YR713
3YR801 - YR806
3YR851 - YR853
3YR951
3YS001
3YS051 - YS052
2. Spares Affected
Refer to Paragraph 2.D., Parts Necessary to Change Spares.
B. Concurrent Requirements
None.
C. Reason
This service bulletin gives instructions to modify the fluid drain path in the wing leading edge area,
forward of the wing front spar. If this service bulletin is not incorporated, flammable fluids accumulating
in the wing leading edge may drain inboard and onto the engine exhaust nozzle, which could result in
a fire.
Boeing has received a report of leaking fuel from the wing leading edge area at the inboard end of the
number 5 leading edge slat. The leak was discovered during a post flight inspection on a 737 airplane
with a fuel quantity of over 2500 pounds. Subsequent investigation found that the leak occurred in an
area of the front spar that does not have a proper drain path. This led to the fuel draining onto the
engine exhaust nozzle. The leak appears to have been caused by loose downstop assembly hardware
of the slat track down stop and is the subject of Boeing Service Letter 737-SL-57-084.
Group 2 airplanes had the wing leading edge drain path incorporated in production, however the parting
agent and Formed-In- Place gasket on the blowout door and fuel shutoff valve access door needs to
be replaced and the new seal disks need to be installed on the latches in the fuel shutoff valve access
door. Group 3 airplanes had the wing leading edge drain path incorporated in production and had the
blowout doors and fuel shutoff valve access doors sealed properly in production, but they need the
new seal disks installed on the latches in the fuel shutoff valve access doors.
Boeing Service Related Problem (SRP) 737NG-SRP-28-0110 and 737NG-SRP-57-0248 are related
to this service bulletin.
Revision 1 was sent to clarify issues that were found during the validation.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
28 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 29

Revision 2 was sent to provide operators with additional assistance for installing the flame arrestor
tube and passing the leak test.
Revision 3 is sent to clarify the requirements for the reidentification of parts and assemblies changed
by this service bulletin.
The data given in Information Notice 737-57-1293 IN 04 and 737-57-1293 IN 05 are included in this
revision.
D. Description
Group 1, Configuration 1:
1. Open the blowout door and the fuel shutoff valve access door. Remove and keep 13 wing lower
leading edge panels from slat station (SS) 26 to slat station (SS) 500 in the left and right wings.
Remove wing upper leading edge panels, if necessary, to help install the flame arrestor tube.
2. Apply sealant to the cavities between the inboard slat track ribs and leading edge lower panels at
SS 47.69, 122.69, 163.95, 240.95, 282.91, 362.51 and 409.09 in the left and right wings.
3. At the outboard leading edge strakelet box, install a flame arrestor tube through the vapor barrier
rib to direct fluids to the strut drain system. Apply sealant to create a form-in-place gasket at the
blowout door located under the strakelet box to prevent fluids from leaking onto the engine exhaust
nozzle. Replace the existing seal in the fuel shut off valve access door with a bulb seal to prevent
flammable fluid leakage onto the engine exhaust nozzle.
4. Install a rubber seal disk under the head of the smaller latch button at each latch location on the
fuel shutoff valve access doors.
5. Close the fuel shutoff valve access door and the blowout door and do a leak test. Install all lower
leading edge access panels, and any upper leading edge panels that may have been removed.
Group 2, Configuration 1:
1. Open the blowout door and the fuel shutoff valve access door in the left and right wings. Remove
and keep the lower leading edge access panel immediately outboard of the fuel shutoff valve
access door in the left and right wings. Remove the parting agent and sealant at these locations
and install new sealant using improved parting agent.
2. Install a rubber seal disk under the head of the smaller latch button at each latch location on the
fuel shutoff valve access doors.
3. Close the blowout door and fuel shutoff valve access door and do a leak test. Install the lower
leading edge access panel.
Group 1-2, Configuration 2; Group 3:
1. Install a rubber seal disk under the head of the smaller latch button at each latch location on the
fuel shutoff valve access doors.
Revision 3 - No more work is necessary on the airplane(s) changed in accordance with Revision 2 of
this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
29 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 30

The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
521, 522, 523, 524, 525, 621, 622, 623, 624, 625737-600, 737-700, 737-700C,
737-800, 737-900
Group 2:
Affected Maintenance Zones
ZoneModel
521, 522, 621, 622737-700, 737-700C, 737-800,
737-900ER
Group 3:
Affected Maintenance Zones
ZoneModel
521, 621737-700, 737-700C, 737-800,
737-900ER
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Federal Aviation Administration (FAA) Notice of Proposed Rule Making NPRM 2008-NM-214-AD, is
related to this service bulletin.
Boeing recommends that the modifications given in this service bulletin be done within 2 years after
the Revision 2 date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
30 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 31

G. Manpower
The table below shows an estimate of the task-hours necessary to do this modification for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task-hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1, Configuration 1:
LEFT WING
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.250.251Preparation
1.001.001Optional Access (a)
2.254.502FIGURE 1
2.502.501FIGURE 4
2.002.001FIGURE 5
3.003.001FIGURE 6
1.001.001FIGURE 7
0.250.251FIGURE 9
2.505.002FIGURE 10
2.254.502FIGURE 11
1.251.251FIGURE 25
17.2524.25TOTAL FOR THE LEFT WING OF THE AIRPLANE
(a) Task may or may not be required to be performed. If task is required, time given must
be added to total shown to arrive at revised total per airplane.
Group 1, Configuration 1:
RIGHT WING
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.250.251Preparation
1.001.001Optional Access (a)
2.004.002FIGURE 13
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
31 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 32

Group 1, Configuration 1:
RIGHT WING
Elapsed HoursTask HoursNumber of Per-
sons
Task
2.502.501FIGURE 16
2.002.001FIGURE 17
3.003.001FIGURE 18
1.001.001FIGURE 19
0.250.251FIGURE 21
2.505.001FIGURE 22
2.004.002FIGURE 23
1.251.251FIGURE 26
16.7523.25TOTAL FOR THE RIGHT WING OF THE AIRPLANE
(a) Task may or may not be required to be performed. If task is required, time given must be
added to total shown to arrive at revised total per airplane.
Group 2, Configuration 1:
LEFT WING
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.250.251Preparation
1.001.001Optional Access (a)
1.001.001FIGURE 2
3.503.501FIGURE 3
2.502.501FIGURE 4
3.003.001FIGURE 8
0.250.251FIGURE 9
1.001.001FIGURE 12
1.251.251FIGURE 25
12.7512.75TOTAL FOR THE LEFT WING OF THE AIRPLANE
(a) Task may or may not be required to be performed. If task is required, time given must be
added to total shown to arrive at revised total per airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
32 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 33

Group 2, Configuration 1:
RIGHT WING
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.250.251Preparation
1.001.001Optional Access (a)
1.001.001FIGURE 14
3.503.501FIGURE 15
2.502.501FIGURE 16
3.003.001FIGURE 20
0.250.251FIGURE 21
1.001.001FIGURE 24
1.251.251FIGURE 26
12.7512.75TOTAL FOR THE RIGHT WING OF THE AIRPLANE
(a) Task may or may not be required to be performed. If task is required, time given must be
added to total shown to arrive at revised total per airplane.
Group 1-2, Configuration 2; Group 3:
LEFT WING
Elapsed HoursTask HoursNumber of PersonsTask
1.251.251FIGURE 25
1.251.25TOTAL FOR THE LEFT WING OF THE
AIRPLANE
Group 1-2, Configuration 2; Group 3:
RIGHT WING
Elapsed HoursTask HoursNumber of PersonsTask
1.251.251FIGURE 26
1.251.25TOTAL FOR THE RIGHT WING OF THE
AIRPLANE
H. Weight and Balance Changes
Group 1, Configuration 1:
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)
+900+1.5
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
33 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 34

Group 2, Configuration 1:
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)
NegligibleNegligible
Group 1-2, Configuration 2; Group 3:
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)
NegligibleNegligible
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 38275-181S, PRR 38275-113S
b. Boeing Service Letter 737-SL-51-042, 737-SL-57-084
c. Boeing Service Related Problem (SRP) 737NG-SRP-28-0110, 737NG-SRP-57-0248
d. Federal Aviation Administration (FAA) Notice of Proposed Rule Making (NPRM)
2008-NM-214-AD
e. Standard Overhaul Practices Manual (SOPM) 20-11-03, 20-30-03, 20-30-93, 20-41-02,
20-43-03, 20-44-04, 20-50-10, 20-50-12, 20-50-19
f. Standard Wiring Practices Manual (SWPM) 20-20-00, 20-20-10
g. 737 Structural Repair Manual (SRM) 51-70-04, 51-70-14
h. 737-600/700/800/900 Aircraft Maintenance Manual (AMM) 27-81-00, 57-41-02
i. BAC 5845
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Seal Application - Leading Edge, Wing Section 14.110A3140
Strakelet Box Installation - Outboard Fixed Leading Edge.116A5500
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
34 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 35

TitleDrawing Number
Access Door Installation - Outboard Fixed Leading Edge.116A8500
Door Assy- Engine Fuel Shutoff/Defuel Valve, Outbd Fixed LE116A8510
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications
Chapter-SectionPublication
57-41737-600/700/800/900 Aircraft Maintenance Manual
52-49, 57-40737-600/700/800/900 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated this service bulletin for effects on Fatigue Critical Structure (FCS) and for
changes to Damage Tolerance Inspections (DTI) required in the Maintenance Program. This
service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary For Each Airplane, for interchangeability and intermixability
information.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
35 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 36

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
36 of 135
BOEING SERVICE BULLETIN 737-57-1293
BLANK PAGE

### Page 37

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary For Each Airplane as shown
below. If there is a limit to the quantity (QTY) of available kits a supply sequence is given by Spares.
More kits become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from the
date Boeing gets the purchase order.
Unit Price thru
(June 30, 2012)
ROLT
(Weeks)
NameKit Number
$1262.00 (b)56 (b)Top Kit - Fuel Drain Path Modifica-
tion
002A0001-111
(a)
(a) Old top kit 002A0001-82 plus a quantity of (4) 116A8505-2 seal disks equals
new kit 002A0001-111.
(b) Kit availability and ROLT is same as seal disk availability and ROLT shown
in the table below.
Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary For Each Airplane as shown
below. If there is a limit to the quantity (QTY) of available parts a supply sequence is given by Spares.
More parts become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from
the date Boeing gets the purchase order.
Unit Price thru
(June 30, 2012)
ROLT
(Weeks)
QTYDateNameEnd Item
$94.00562510/03/11Seal Disk116A8505-2
2510/17/11
25 (a)10/31/11
(a) A quantity of 25 Seal Disks will be released every 2 weeks until 06/10/13.
The kits and seal disks are subject to the terms and conditions of the Boeing standard purchase order
acknowledgment. After the Unit Price date, new price and ROLT data is applicable. Prices are in United
States dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that
follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Spares Customer Support - MC 36-65 Boeing Spares Department P.O. Box 3707 Seattle,
Washington 98124-2207 USA
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST
RESPONDER AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE
INFORMATION
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
37 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 38

B. Industry Support Information
Boeing warranty remedies are available for 737 airplanes in warranty as of April 28, 2006. For task
hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing
Commercial Airplanes Group - Warranties. The kits or parts for airplanes in warranty as of that date
will be supplied at no charge. Send a purchase order for the kits or parts to Boeing Spares. Please
refer to this service bulletin number and reference the airplane variable numbers in your purchase
order.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
Group 1, Configuration 1:
a. To get the kits shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied
by the Operator, are necessary for each airplane.
Group 1, Configuration 1:
Kit 002A0001-111
NotesExisting Part
Number
NameFigureNew Part Number
2625181765
Qty
FLAME ARRESTOR
TUBE
---1-1116A5515-1
SEAL--1-1-116A8503-13
SEAL RETAINER--1-1-116A8504-9
BOLT, 100 DEG
SHEAR
---1-1BACB30XD3K3
BOLT, 100 DEG
SHEAR
--6-6-BACB30XD3K5
BOLT, 100 DEG
SHEAR
--7-7-BACB30XD3K6
BOLT, 100 DEG
SHEAR
--2-2-BACB30XD3K8
BOLT--2-2-BACB30ZE3-6
(a)CLAMP---1-1BACC10HM08P
BONDING JUMPER--1-1-BACJ40AB20-6
NUT--171171BACN10YR3CD
SHIM, LAMINATED--1-1-BACS40R010C162F
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
38 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 39

Group 1, Configuration 1:
Kit 002A0001-111
NotesExisting Part
Number
NameFigureNew Part Number
2625181765
Qty
WASHER DIMPLED--1-1-BACW10DM6P
WASHER--2-2-NAS1149D0316H
WASHER--8181NAS1149D0332J
Seal Disk22----116A8505-2
(a) BACC10HM08PW is an acceptable substitute for BACC10HM08P.
Group 1, Configuration 2; Group 2-3:
a. To get the parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: Four Seal Disks and the items shown in Paragraph 2.C.2., Parts and Materials
Supplied by the Operator, are necessary for each airplane.
Group 1, Configuration 2; Group 2-3:
End Item Parts
NotesExisting Part
Number
NameFigureNew Part Number
2625181765
Qty
Seal Disk22----116A8505-2
2. Parts and Materials Supplied by the Operator:
Group 1, Configuration 1:
NotesNameQTYPart Number / Specification
(e)Cleaning Agent10 OuncesMethyl Ethyl Ketone (MEK)
(a)Sealant20 OuncesBMS5-45, Class B-1/2
(a) (f)Sealant30 OuncesBMS5-45, Class B-1/2 or B-2
(b)Chemical Conversion
Coating
4 OuncesType 2, Class A
(a)Primer2 ouncesBMS10-11, Type I
(a)Primer2 OuncesBMS10-79, Type III
(a)Gloss Enamel2 OuncesBMS10-11, Type II
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
39 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 40

Group 1, Configuration 1:
NotesNameQTYPart Number / Specification
(a)Gloss Enamel2 OuncesBMS10-60, Type II
-Blind Rivets12BACR15FP6MP5R
(a)Sealant4 OuncesBMS5-142 Class B-1/2 or B-2
(c)Parting Agent8 OuncesFrekote 710-NC
(d)Washer4NAS1149D0316H
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification
(BMS) for supplier data.
(b) Refer to SOPM 20-43-03 as an accepted procedure or 737 SRM Chapter 51 for mate-
rial sources.
(c) Petrolatum that meets VV-P-236 specifications is an acceptable substitute for Frekote
710-NC.
(d) As an option you may salvage and re-install the removed washers.
(e) Refer to SOPM 20-30-93 as an accepted procedure.
(f) BMS5-36, Type II is an acceptable substitute adhesive for Figures 25 and 26 only.
Refer to SOPM 20-50-12 Type 50, Method 1 as an accepted procedure.
Group 2, Configuration 1:
NotesNameQTYPart Number / Specification
(d)Cleaning Agent5 OuncesMethyl Ethyl Ketone (MEK)
(a)Sealant10 ouncesBMS5-45, Class B-1/2
(a) (e)Sealant20 OuncesBMS5-45, Class B-1/2 or B-2
(b)Chemical Conversion
Coating
2 OuncesType 2, Class A
(a)Primer1 OunceBMS10-79, Type III
(a)Gloss Enamel1 OunceBMS10-60, Type II
-Blind Rivets12BACR15FP6MP5R
(c)Parting Agent6 OuncesFrekote 710-NC
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification
(BMS) for supplier data.
(b) Refer to SOPM 20-43-03 as an accepted procedure or 737 SRM Chapter 51 for mate-
rial sources.
(c) Petrolatum that meets VV-P-236 specifications is an acceptable substitute for Frekote
710-NC.
(d) Refer to SOPM 20-30-93 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
40 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 41

Group 2, Configuration 1:
NotesNameQTYPart Number / Specification
(e) BMS5-36, Type II is an acceptable substitute adhesive for Figures 25 and 26 only.
Refer to SOPM 20-50-12 Type 50, Method 1 as an accepted procedure.
Group 1-2, Configuration 2; Group 3:
NotesNameQTYPart Number / Specification
(a) (b)Sealant1 OunceBMS5-45, Class B-1/2 or B-2
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification
(BMS) for supplier data.
(b) BMS5-36, Type II is an acceptable substitute adhesive for Figures 25 and 26 only.
Refer to SOPM 20-50-12 Type 50, Method 1 as an accepted procedure.
3. Parts Modified and Reidentified:
Group 1, Configuration 1:
NotesNew Part NumberNameQTYExisting Part
Number
(a)116A5508-11Seal Rib1116A5508-3
116A5508-5
116A5508-7
116A5508-9
(a)116A5508-12Seal Rib1116A5508-4
116A5508-6
116A5508-8
116A5508-10
(a)116A5510-23Strakelet Box Assembly1116A5510-9
116A5510-11
116A5510-13
116A5510-17
116A5510-19
116A5510-21
(a)116A5510-24Strakelet Box Assembly1116A5510-10
116A5510-12
116A5510-14
116A5510-18
116A5510-20
116A5510-22
Ref. 521BB116A8510-19Fuel Shutoff Valve Access
Door Assembly
1116A8510-13
(a) (b)
Ref. 621BB116A8510-20Fuel Shutoff Valve Access
Door Assembly
1116A8510-14
(a) (b)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
41 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 42

Group 1, Configuration 1:
NotesNew Part NumberNameQTYExisting Part
Number
(a)116A5522-9Hinge Half1116A5522-5
(a)116A5522-10Hinge Half1116A5522-6
(a)116A5522-7Hinge Assembly1116A5522-1
(a)116A5522-8Hinge Assembly1116A5522-2
(a)116A5507-9Door Land Assembly1116A5507-1
116A5507-7
(a)116A5507-10Door Land Assembly1116A5507-2
116A5507-8
(a)116A8505-1Latch Assembly4H3479-5
(a) Make the change given in this service bulletin.
(b) Reworked 116A8510-9 or 116A8510-10 Fuel Shutoff Valve Access Door Assemblies
do not have an equivalent Boeing part number because they have a different hinge
component.
Group 2, Configuration 1:
NotesNew Part NumberNameQTYExisting Part
Number
(a)116A5522-9Hinge Half1116A5522-5
(a)116A5522-10Hinge Half1116A5522-6
(a)116A5522-7Hinge Assembly1116A5522-1
(a)116A5522-8Hinge Assembly1116A5522-2
Ref. 521BB116A8510-19Fuel Shutoff Valve Access
Door Assembly
1116A8510-17
(a)
Ref. 621BB116A8510-20Fuel Shutoff Valve Access
Door Assembly
1116A8510-18
(a)
(a)116A8505-1Latch Assembly4H3479-5
(a) Make the change given in this service bulletin.
Group 1-2, Configuration 2; Group 3:
NotesNew Part NumberNameQTYExisting Part
Number
Ref. 521BB116A8510-19Fuel Shutoff Valve Access
Door Assembly
1116A8510-17
(a)
Ref. 621BB116A8510-20Fuel Shutoff Valve Access
Door Assembly
1116A8510-18
(a)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
42 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 43

Group 1-2, Configuration 2; Group 3:
NotesNew Part NumberNameQTYExisting Part
Number
(a)116A8505-1Latch Assembly4H3479-5
(a) Make the change given in this service bulletin.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
To get the parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
Group 1, Configuration 1:
QTYNamePart Number
2Seal116A8503-13
2Seal Retainer116A8504-9
4Seal Disk116A8505-2
Group 1, Configuration 2; Group 2-3:
QTYNamePart Number
4Seal Disk116A8505-2
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
43 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 44

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
44 of 135
BOEING SERVICE BULLETIN 737-57-1293
BLANK PAGE

### Page 45

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in 737 SRM Chapter
51
– Torque limits to tighten nuts and bolts are in 737 SRM Chapter 51
4. Use the approved fastener and process material substitutions in accordance with
737 SRM Chapter 51.
5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
6. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
7. If the length of any fastener specified in this service bulletin does not meet installation
standards given in 737 SRM Chapter 51, then a fastener of the same specification,
or an approved substitute, with a length which meets the installation standards given
in 737 SRM Chapter 51 may be used. In addition, washers may be installed for
fastener grip length in accordance with 737 SRM Chapter 51.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
45 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 46

9. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
10. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
11. Boeing Service Letter 737-SL-51-042, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
12. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
13. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
14. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
15. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
B. WORK INSTRUCTIONS
Group 1, Configuration 1:
1. Extend the leading edge slats to the fully down position. Refer to 737-600/700/800/900 AMM
27-81-00 as an accepted procedure.
2. Deactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
3. Do the fuel drain path modification as follows:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
46 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 47

LEFT WING
a. Open the left wing blowout door, fuel shutoff valve access door and remove the left wing
leading edge lower panels to get access to the leading edge slat track ribs in accordance with
FIGURE 1.
b. Remove, if necessary, access panel 521AT.
c. Trim the blowout door hinge in the left wing in accordance with FIGURE 4.
NOTE: It might be necessary to remove the hinge pin from the hinge assembly, in order to
trim the hinge half.
d. Install a flame arrestor tube through the vapor barrier rib in the left outboard strakelet box in
accordance with FIGURE 5.
e. Replace the seal and the seal retainer on the left fuel shutoff valve access door in accordance
with FIGURE 6.
(1) Do a detailed inspection on the countersink diameter for the bonding jumper fastener
hole in the left fuel shutoff valve access door. The 100 degree countersink hole should
have a diameter of 0.310 to 0.320 inches. Repair the left fuel shutoff valve access door
if the diameter of the countersink is outside this range. Refer to 737 SRM 51-70-04 and
737 SRM 51-70-14 as accepted procedures.
f. Apply sealant to the blowout door and fuel shutoff valve access door in the left wing in
accordance with FIGURE 7.
g. Install a seal disk on each latch in the fuel shutoff valve access door in the left wing in
accordance with FIGURE 25.
h. With the blowout door and fuel shutoff valve access door in the left wing closed, do a leak
test in accordance with FIGURE 9.
(1) If water drains through the strut drain tube and no water drips onto the engine nozzle
within 2 minutes of pouring the water, then the test is successful.
(2) If water does not drain through the strut drain tube, then find and remove whatever is
blocking the drain path. Repeat leak test in accordance with FIGURE 9.
(3) If water drips onto the engine nozzle within 2 minutes of pouring the water, then reapply
sealant as required until the test is successful.
i. Apply sealant to the left wing leading edge slat track ribs at SS 47.69, 122.69, 163.95, 240.95,
282.91, 362.51 and 409.09 in accordance with FIGURE 10.
j. Close the blowout door, fuel shutoff valve access door and install the leading edge lower
panels in the left wing in accordance with FIGURE 11.
k. Close panel 521AT, if the panel was removed.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
47 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 48

RIGHT WING
a. Open the right wing blowout door, fuel shutoff valve access door and remove the right wing
leading edge lower panels to get access to the leading edge slat track ribs in accordance with
FIGURE 13.
b. Remove, if necessary, access panel 621AT.
c. Trim the blowout door hinge in the right wing in accordance with FIGURE 16.
NOTE: It might be necessary to remove the hinge pin from the hinge assembly, in order to
trim the hinge half.
d. Install a flame arrestor tube through the vapor barrier rib at the right outboard strakelet box
in accordance with FIGURE 17.
e. Replace the seal and seal retainer on the right fuel shutoff valve access door in accordance
with FIGURE 18.
(1) Do a detailed inspection on the countersink diameter for the bonding jumper fastener
hole in the right fuel shutoff valve access door. The 100 degree countersink hole should
have a diameter of 0.310 to 0.320 inches. Repair the right fuel shutoff valve access door
if the diameter of the countersink is outside this range. Refer to 737 SRM 51-70-04 and
737 SRM 51-70-14 as accepted procedures.
f. Apply sealant to the blowout door and fuel shutoff valve access door in the right wing in
accordance with FIGURE 19.
g. Install a seal disk on each latch in the fuel shutoff valve access door in the right wing in
accordance with FIGURE 26.
h. With the blowout door and fuel shutoff valve access door in the right wing closed, do a leak
test in accordance with FIGURE 21.
(1) If water drains through the strut drain tube and no water drips onto the engine nozzle
within 2 minutes of pouring the water, then the test is successful.
(2) If water does not drain through the strut drain tube, then find and remove whatever is
blocking the drain path. Repeat leak test in accordance with FIGURE 21.
(3) If water drips onto the engine nozzle within 2 minutes of pouring the water, then reapply
sealant as required until the test is successful.
i. Apply sealant to the right wing leading edge slat track ribs at SS 47.69, 122.69, 163.95, 240.95,
282.91, 362.51 and 409.09 in accordance with FIGURE 22.
j. Close the blowout door, fuel shutoff valve access door and install the leading edge lower
panels in the right wing in accordance with FIGURE 23.
k. Close panel 621AT, if the panel was removed.
4. Reactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
48 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 49

5. Retract the leading edge slats to the fully up position. Refer to 737-600/700/800/900 AMM 27-81-00
as an accepted procedure.
6. Put the airplane back to a serviceable condition.
Group 2, Configuration 1:
1. Extend the leading edge slats to the fully down position. Refer to 737-600/700/800/900 AMM
27-81-00 as an accepted procedure.
2. Deactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
3. Change seal at the blowout door and fuel shutoff valve access door as follows:
LEFT WING
a. Open the left wing blowout door, fuel shutoff valve access door and remove access panel
521CB in accordance with FIGURE 2.
b. Remove, if necessary, access panel 521AT.
c. Remove the parting agent and the sealant from the blowout door, fuel shutoff valve access
door and panel 521CB, and do a general visual inspection of the blowout door hinge in the
left wing in accordance with FIGURE 3.
(1) If the blowout door hinge is not trimmed, trim the blowout door hinge in accordance with
FIGURE 4.
NOTE: It might be necessary to remove the hinge pin from the hinge assembly, in order
to trim the hinge half.
(2) If the blowout door hinge is trimmed, continue with the next step.
d. Apply new parting agent and sealant to the blowout door and fuel shutoff valve access door
in the left wing in accordance with FIGURE 8.
e. Install a seal disk on each latch in the fuel shutoff valve access door in the left wing in
accordance with FIGURE 25.
f. With the blowout door and fuel shutoff valve access door in the left wing closed, do a leak
test in accordance with FIGURE 9.
(1) If water drains through the strut drain tube and no water drips onto the engine nozzle
within 2 minutes of pouring the water, then the test is successful.
(2) If water does not drain through the strut drain tube, then find and remove whatever is
blocking the drain path. Repeat leak test in accordance with FIGURE 9.
(3) If water drips onto the engine nozzle within 2 minutes of pouring the water, then reapply
sealant as required until the test is successful.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
49 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 50

NOTE: It may be necessary to do FIGURE 3 and FIGURE 8 again to achieve a proper
seal.
g. Close the blowout door, fuel shutoff valve access door and panel 521CB in the left wing in
accordance with FIGURE 12.
h. Close panel 521AT, if the panel was removed.
RIGHT WING
a. Open the right wing blowout door, fuel shutoff valve access door and remove access panel
621CB in accordance with FIGURE 14.
b. Remove, if necessary, access panel 621AT.
c. Remove the parting agent and the sealant from the blowout door, fuel shutoff valve access
door and panel 621CB and do a general visual inspection of the blowout door hinge in the
right wing in accordance with FIGURE 15.
(1) If the blowout door hinge is not trimmed, trim the blowout door hinge in accordance with
FIGURE 16.
NOTE: It might be necessary to remove the hinge pin from the hinge assembly, in order
to trim the hinge half.
(2) If the blowout door hinge is trimmed, continue with the next step.
d. Apply new parting agent and sealant to the blowout door and fuel shutoff valve access door
in the right wing in accordance with FIGURE 20.
e. Install a seal disk on each latch in the fuel shutoff valve access door in the right wing in
accordance with FIGURE 26.
f. With the blowout door and fuel shutoff valve access door in the right wing closed, do a leak
test in accordance with FIGURE 21.
(1) If water drains through the strut drain tube and no water drips onto the engine nozzle
within 2 minutes of pouring the water, then the test is successful.
(2) If water does not drain through the strut drain tube, then find and remove whatever is
blocking the drain path. Repeat leak test in accordance with FIGURE 21.
(3) If water drips onto the engine nozzle within 2 minutes of pouring the water, then reapply
sealant as required until the test is successful.
NOTE: It may be necessary to do FIGURE 15 and FIGURE 20 again to achieve a proper
seal.
g. Close the blowout door, fuel shutoff valve access door and panel 621CB in the right wing in
accordance with FIGURE 24.
h. Close panel 621AT, if the panel was removed.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
50 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 51

4. Reactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
5. Retract the leading edge slats to the fully up position. Refer to 737-600/700/800/900 AMM 27-81-00
as an accepted procedure.
6. Put the airplane back to a serviceable condition.
Group 1-2, Configuration 2; Group 3:
1. Deactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
2. Install a seal disk on each latch in the fuel shutoff valve access door as follows:
LEFT WING
a. Open the left wing fuel shutoff valve access door.
b. Install the seal disks in the latches of the left wing fuel shutoff valve access door in accordance
with FIGURE 25.
RIGHT WING
a. Open the right wing fuel shutoff valve access door.
b. Install seal disks in the latches of the right wing fuel shutoff valve access door in accordance
with FIGURE 26.
3. Group 1-2, Configuration 2:
If Revision 1 of the service bulletin was incorporated on an airplane, but failed the leak test at one
of the latch locations in the fuel shutoff valve access door, then do the leak test in accordance with
FIGURE 9 (for the left wing), or FIGURE 21 (for the right wing), as applicable, after installing the
seal disks on the latches.
a. If water drains through the strut drain tube and no water drips onto the engine nozzle within
2 minutes of pouring the water, then the test is successful.
b. If water does not drain through the strut drain tube, then find and remove whatever is blocking
the drain path. Repeat leak test in accordance with FIGURE 9 (for the left wing), or FIGURE
21 (for the right wing), as applicable.
4. Reactivate the leading edge slat system. Refer to 737-600/700/800/900 AMM 27-81-00 as an
accepted procedure.
5. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3: December 14, 2012
51 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 52 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
This Figure applies only to: Group 1, Configuration 1.
FWD
INBD \
LEFT WING  1343464
(VIEW LOOKING UP)
FIGURE 1: LEFT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS
(SHEET 1 OF 2)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57-1293
Work - See page 1 for details.  52 of 135

### Page 53

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
-1521ABBLOWOUT DOOROpen1
-1521BBFUEL SHUTOFF VALVE
ACCESS DOOR
(a)1521CBACCESS PANELRemove / Keep2
(a)1521FBACCESS PANELRemove / Keep3
1521GB
1521HB
1521JB
(a)1521MBACCESS PANELRemove / Keep4
1521NB
1521PB
1521QB
(a)1521TBACCESS PANELRemove / Keep5
1521UB
1521VB
1521WB
(a) Refer to 737-600/700/800/900 AMM 57-41-02 as an accepted procedure.
FIGURE 1: LEFT WING - LEADING EDGE SLAT TRACK RIBS - ACCESS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3 December 14, 2012
53 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 54 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
This Figure applies only to: Group 2, Configuration 1.
FWD
INBD \
LEFT WING  1570851
(VIEW LOOKING UP)
FIGURE 2: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS
(SHEET 1 OF 2)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57-1293
Work - See page 1 for details.  54 of 135

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
-1521ABBLOWOUT DOOROpen1
-1521BBFUEL SHUTOFF VALVE
ACCESS DOOR
Open
(a)1521CBACCESS PANELRemove/Keep2
(a) Refer to 737-600/700/800/900 AMM 57-41-02 as an accepted procedure.
FIGURE 2: LEFT WING - BLOWOUT DOOR AND FUEL SHUTOFF VALVE ACCESS DOOR - ACCESS
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3 December 14, 2012
55 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 56 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
This Figure applies only to: Group 2, Configuration 1.
LEFT WING
SEE A
SEE
SS
SEAL RIB/  47.69
STOP ASSY
LOWER
SKIN
PANEL
LOWER
PANEL
ASSEMBLY
FWD
INBD C  1813672
VIEW LOOKING UP
FIGURE 3: LEFT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE
BLOWOUT DOOR HINGE
(SHEET 1 OF 3)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57-1293
Work - See page 1 for details.  56 of 135

### Page 57 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
Ф
HINGE
Ф
BLOWOUT DOOR
INSIDE VIEW OF BLOWOUT DOOR,
HINGE SHOWN TRIMMED
Ф  HINGE
BLOWOUT DOOR
INSIDE VIEW OF BLOWOUT DOOR,  1570865
HINGE SHOWN UNTRIMMED
FIGURE 3: LEFT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE
BLOWOUT DOOR HINGE
(SHEET 2 OF 3)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  737-57-1293
Work - See page 1 for details.  57 of 135

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
--AZ-534-2BPARTING AGENTRemove1
(a)-BMS5-45, Class B-
1/2 or B-2
SEALANTRemove
(b) (c)--BLOWOUT DOOR SURROUNDClean2
--FUEL SHUTOFF VALVE AC-
CESS DOOR SURROUND
Clean
2-RIBClean
Do a General Visual In-
spection to determine if
both ends of the hinge
half are trimmed approx-
imately as shown.
1116A5522-( )HINGE HALFInspect3
(a) Remove the existing formed-in-place gasket from both door openings and panel opening. Use a plastic
scraper. You do not need to remove the sealant from the machined gap, if it is not damaged. Refer to
SOPM 20-50-19 as an accepted procedure.
(b) Remove all the corrosion inhibiting compound from the area shown. Refer to SOPM 20-50-19 as an ac-
cepted procedure.
(c) If the Teflon coating on the door surround structure is damaged or shows signs of abrasion, apply one
coat of BMS10-11, Type I primer. Refer to SOPM 20-41-02 as an accepted procedure. Also apply one
coat of BMS10-60, Type I semi-gloss enamel. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 3: LEFT WING - PARTING AGENT AND SEALANT REMOVAL, AND INSPECTION OF THE
BLOWOUT DOOR HINGE
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 13, 2008
737-57-1293Revision 3 December 14, 2012
58 of 135
BOEING SERVICE BULLETIN 737-57-1293

### Page 59 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
This Figure applies only to: Group 1-2, Configuration 1.
\ SEE
LEFT WING
... .
(2)10
6 LOCATIONS
SEE ®
FWD C
INBD
VIEW LOOKING UP
FIGURE 4: LEFT WING - BLOWOUT DOOR HINGE TRIM
(SHEET 1 OF 3)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  737-57-1293  59 of 135

### Page 60 (OCR)

BOEING SERVICE BULLETIN 737-57-1293
SEE C  4 SEE C
Ф
Ф
BLOWOUT DOOR
R 0.30
—R 0.30
0.12 R  0:12 R
0.06
1570450
FIGURE 4: LEFT WING - BLOWOUT DOOR HINGE TRIM
(SHEET 2 OF 3)
Original Issue: November 13, 2008
Revision 3 December 14, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  737-57-1293
Work - See page 1 for details.  60 of 135

The text continues at https://openairdocs.org/service-documents/boeing/sb-737-57-1293/file/eceae11611da.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
