# Boeing Special Attention Service Bulletin 747-25-3381: Revision 3, part 2 of 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2021-0794; AD 2021-26-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 747-25-3381](https://openairdocs.org/service-documents/boeing/sb-747-25-3381.md)
- Title as filed: SB-747-25-3381-03-- BOEING_Part2
- Pages: 106
- PDF: https://openairdocs.org/files/sha256/9d/f6/9df69edca9eb5dd9f3540eb1e4b295fec3c6626c710108d43491a0d1ca101807
- Page: https://openairdocs.org/service-documents/boeing/sb-747-25-3381/file/9df69edca9eb

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
STA
1540
STA
STA  1560
1480
STA
STA  1500
580
STA
STA  600
520
STA
STA  540
340
STA
WL  360
235
UP
INBD  00300
FOAM AIR SEAL
LOCATIONS
STA
1840
STA
1860
WL
233
UP
FWD •
00300
INBD *  FOAM AIR SEAL
LOCATIONS  2395540
FIGURE 6: MAIN DECK SYSTEM TUBE/IRE FOAM SEAL REPLACEMENT, RIGHT SIDEWALL
(SHEET 3 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  108 of 213

### Page 2 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
STA
2080
STA
STA  2100
1960
WL  STA
233 -  1980
INBD C  00300
FOAM AIR SEAL
LOCATIONS
340 430  STA STA  SEE F  SIDEWALL  UPPER  PANEL  SIDEWALL LIGHT  REVEAL PANEL  2100  STA
LOWER
SIDEWALL
PANEL
FLOOR
DADO
PANEL  FWD
INBD C  AIR  GRILLE
MAIN DECK, RIGHT SIDE WALL  COVER
STRIP  2574517
FIGURE 6: MAIN DECK SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT, RIGHT SIDEWALL
(SHEET 4 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  109 of 213

### Page 3 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
CEILING  BLANKET
PANEL  - FABRIC TAB
CAPSTRIP
SYSTEM HOSE
• BLANKET
INBD C
BLANKET
1 INCH FLAP  FWD C
FRAME
TYPICAL
SYSTEM  TAPE S  SYSTEM
RUN HOSE  12S TAPE OR  RUN HOSE
TIE WRAP
INSULATION
BLANKET
FLAP
BLANKET  12OO FOAM  BLANKET
ASSEMBLY
ASSEMBLY  WITH AN INSULATION BLANKET FLAP  TYPICAL  WITHOUT AN INSULATION BLANKET FLAP  TYPICAL  2574520
C-C  c-c
FIGURE 6: MAIN DECK SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT, RIGHT SIDEWALL
(SHEET 5 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright @ Unpublished  747-25-3381
Work - See page 1 for details.  110 of 213

### Page 4

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each step.
For bulk material rolls, the quantity number shown in the first-use step is the total number of rolls provided in
the top kit. The quantity number is not shown in the figure-steps thereafter.
NOTE: If the side wall linings are not removed, refer to 747-400 AMM 25-59-01 as an accepted
procedure for removal.
1.
2. The location of the system tube or wire penetrations, shown in this figure, are typical. Operators
should look only for similar penetrations between STA 340 and STA 2100. When similar
penetrations are found, make only the change given in this figure at those locations.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(d)(e)--FOAMInspect1
From around insulation blanket
flap located where tubes or
wires penetrate the sidewall in-
sulation.
--TAPE OR TIE
WRAP
Remove2
Surface before the new foam
tape is installed.(b)
--SYSTEM TUBES
AND OR WIRES
Clean3
Surface before the new foam
tape is installed.(b)
--INSULATION
BLANKET FLAP
Clean
Around system tubes or wires
to make sure tubes or wires are
separated. Fill all the open
spaces with foam when multiple
tubes or wires pierce the insula-
tion blanket. (c)
-015U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Put/Hold4
From the bulk material roll. Cut
a piece that is 5 inches long, or
cut more if more is required to
make a smoke barrier. (c)
1015U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Install (New)
Enough from bulk material roll
to wrap around the insulation
blanket flap.
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPECut5
Around insulation blanket flap
and tubes or wires. Make sure
the tape tightly holds the insula-
tion blanket flap so there is no
air space and a smoke barrier
is made. (f)
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPEInstall (New)
FIGURE 6: MAIN DECK SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT, RIGHT SIDEWALL
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
111 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 5

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Identify in the vicinity of re-
placed foam tape that this ser-
vice bulletin was done. Refer to
SOPM 20-50-10 as an accepted
procedure for part marking.
--NEW FOAM TAPEIdentify6
(a) Do a general visual inspection on left sidewall between station 340 and station 2100 on the main deck.
Inspect for foam around system runs. If BMS 8-39 found, remove and replace it with the new material.
(b) Refer to SOPM 20-30-03 as an accepted procedure.
(c) Where system tubes or wires penetrate the insulation blanket, make sure all the space inside the insu-
lation blanket flap is filled with foam tape to create a smoke barrier.
(d) Refer to Table 2 in APPENDIX D for a list of existing part numbers for this Figure.
(e) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
(f) Install tape where BMS 1-68 is used to seal system run penetrations through the insulation blanket. If
there is no blanket flap or tab present, use tape to attach the foam seal to the insulation blanket.
FIGURE 6: MAIN DECK SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT, RIGHT SIDEWALL
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
112 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 6 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 6-10, Configuration 1; Group 10, Configuration 2; Group 12-13,
Configuration 1; Group 13, Configuration 4; Group 14, Configuration 1, 4; Group 15-16, Configuration
1; Group 16, Configuration 2, 5; Group 17, Configuration 1-2, 5; Group 18-19, Configuration 1; Group 19,
Configuration 2, 5.
SEE B
SEE
SEE
STA
FLOOR  • 680
FWD C  BEAM  →END
VERTICAL  INSULATION
POST  • BLANKET
STABILIZER  STA
ANGLE  *460
INSULATION
BLANKET
UP
FORWARD  CARGO COMPARTMENT  LEFT SIDE  FWD
D90354
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 1 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  113 of 213

### Page 7 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
- VERTICAL
POST
STABILIZER
ANGLE -  INSULATION
BLANKET
1 BLANKET
FLAP
1OOTAPE OR
TIE WRAP
STRINGER
S-34
A-A
(TYPICAL ARRANGEMENT USED
WHERE SYSTEMS PIERCE S-34 TO
STABILIZER ANGLE FIRE BARRIER)
DEO TAPE OR
SYSTEM RUN 3  TIE WRAI
12OO FOAM
B-B  SEAL  D90394
(TYPICAL)
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 2 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  L8EE-SZ-LĐL
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  114 of 213

### Page 8 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
STA
820  FLOOR
BEAM
STABILIZER
ANGLE
STA
960
INSULATION
BLANKET
@FWD
LEFT SIDE
FORWARD CARGO
COMPARTMENT
D90530
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 3 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  115 of 213

### Page 9 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
FORWARD CARGO COMPARTMENT  FORWARD CARGO COMPARTMENT
AFT END WALL  FORWARD END WALL
INSULATION  INSULATION
BLANKET FLAP  BLANKET FLAP
HALFCAP.  HALFCAP
TAPE OR  TAPE OR
TIE WRAP  TIE WRAP
125
4
10€
TAPE OR  TAPE OR
TIE WRAP  HALFCAP  TIE WRAP  HALFCAP
TYPICAL  TYPICAL
ARRANGEMENT FOR SYSTEMS PENETRATION
OF FRAME WHEN AN INSULATION BLANKET
FLAP IS PRESENT
ARRANGEMENT FOR SYSTEMS PENETRATION
OF FRAME  WHEN AN INSULATION BLANKET
FLAP IS PRESENT
C-C  D-D
SYSTEM 3  DOO TAPE OR
RUN  TIE WRAP
TAPE OR  TIE WRAP  3) SYSTEM  RUN
100  ) SYSTEM RUN
SYSTEM 3
RUN
E-E  E-E  DOOO SA  SEAI
EXAMPLE, WHERE FOAM  IS NOT REQUIRED)  (EXAMPLE, WHERE FOAM  IS REQUIRED)  D90391
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 4 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  116 of 213

### Page 10 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
FLOOR
BEAM  STA
460
STABILIZER
ANGLE
STA
960
INSULATION
BLANKET
RIGHT SIDE
FORWARD CARGO
COMPARTMENT
F WD <
D90535
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 5 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  117 of 213

### Page 11 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
FORWARD CARGO COMPARTMENT  FORWARD CARGO COMPARTMENT
AFT END WALL  FORWARD END WALL
TAPE  TAPE
120
NEW FOAM  NEW FOAM
WRAPPED  WRAPPED*
IN TAPE  IN TAPE
100  100
TAPE  TAPE
→ FWD
TYPICAL ARRANGEMENT FOR
SYSTEMS PENETRATION WHEN AN
INSULATION BLANKET FLAP IS
NOT PRESENT
C-C
TYPICAL ARRANGEMENT FOR
SYSTEMS PENETRATION WHEN AN
INSULATION BLANKET FLAP IS
NOT PRESENT
D-D
TAPE F  SYSTEM
RUN HOSE
SYSTEM 3  DO TAPE OR
RUN  TIE WRAP
3) SYSTEM
RUN
SYSTEM (3
RUN
206 FOAM
SEAL
TYPICAL  TYPICAL  BLANKET
F-F  G-G
ASSEMBLY
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 6 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  118 of 213

### Page 12

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown for parts used in each step are the total number of parts necessary for each step.
For bulk material rolls, the quantity number shown in the first-use step is the total number of rolls provided in
the top kit. The quantity number is not shown in the figure-steps thereafter.
NOTE: If the sidewall linings, ball transfer panels and roller trays were not removed, refer to 747-400
AMM 25-52-01 and 747-400 AMM 25-53-15 as accepted procedures for removal.
1.
2. The locations of the system tube or wire penetrations on the sloping sidewall, shown in this
figure, are typical. Inspect for similar penetrations around the perimeter STA 460 to STA 960,
along the stabilizer angle near Stringer S-34. Any penetrations through the insulation blankets
between the applicable stringer and the applicable stabilizer angle must be sealed for
halon/smoke retention. Refer to APPENDIX C for an illustrated visual aid.
3. The locations of the system tube or wire penetrations under the floor, shown in this figure, are
typical. Inspect for similar penetrations on the insulation blanket from the left to right side
between STA 460 and STA 960. Refer to APPENDIX C for an illustrated visual aid. Any
penetrations through the insulation blankets must be sealed for halon/smoke retention.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to Notes 1 and2. (a)(c)(d)--FOAMInspect1
From around insulation blanket
flap located where tubes or
wires penetrate the insulation.
Refer to Note 2.
--TAPE OR TIE
WRAP
Remove2
From inside the insulation blan-
ket flap. (c)(d)
--FOAMRemove
Surface before the new foam
tape is installed. Use mechani-
cal means to remove debris.
--SYSTEM RUNClean3
Surface before the new foam
tape is installed. Use mechani-
cal means to remove debris.
--INSULATION
BLANKET FLAP
Clean
Around system tubes or wires
to make sure tubes or wires are
separated. Fill all the open
spaces when multiple tubes or
wires pierce the insulation blan-
ket. (b)
-15U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Put/Hold4
From the bulk material roll. Cut
a piece that is 5 inches long, or
cut more if more is required to
make a smoke barrier. (b)
-015U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Install (New)
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
119 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 13

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Enough from bulk material roll
to wrap around the insulation
blanket flap.
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPECut5
Around insulation blanket flap
and tubes or wires. Make sure
the tape tightly holds the insula-
tion blanket flap so there is no
air space and a smoke barrier
is made. (e)
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPEInstall (New)
Identify in the vicinity of re-
placed foam tape that this ser-
vice bulletin was done. Refer to
SOPM 20-50-10 as an accepted
procedure for part marking.
--NEW FOAM TAPEIdentify6
(a) Do a general visual inspection of the FWD cargo compartment area between station 460 and station
960. Inspect for foam around system runs. If BMS 8-39 found, remove and replace it with the new ma-
terial.
(b) Where system tubes or wires penetrate the insulation blanket, make sure all the space inside the insu-
lation blanket flap is filled with foam tape to create a smoke barrier.
(c) Refer to Table 6 in APPENDIX D for a list of existing part numbers for this Figure.
(d) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
(e) Install tape where BMS 1-68 is used to seal system run penetrations through the insulation blanket. If
there is no blanket flap or tab present, use tape to attach the foam seal to the insulation blanket.
FIGURE 7: FORWARD CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
120 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 14 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 6-10, Configuration 1; Group 10, Configuration 2; Group 12-16,
Configuration 1; Group 16, Configuration 2; Group 17, Configuration 1-2; Group 18-19, Configuration 1;
Group 19, Configuration 2.
SEE ®
SEE (C
SEE A
STA
1720
FLOOR
BEAM
VERTICAL  INSULATION
POST  BLANKET
STA
STABILIZER  1600
ANGLE
INSULATION
BLANKET
LEFT SIDE
AFT CARGO COMPARTMENT
→ FWD  D91009
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 1 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  121 of 213

### Page 15 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
- VERTICAL
POST
STABILIZER
ANGLE  INSULATION
BLANKET
1 BLANKET
FLAP
OOOTAPE OR
TIE WRAP
STRINGER
S-34  A-A
(TYPICAL ARRANGEMENT USED
WHERE SYSTEMS PIERCE S-34 TO
STABILIZER ANGLE FIRE BARRIER)
SYSTEM 3  RUN  DOO TAPE OR  TIE WRAI
3 SYSTEM
RUN
SYSTEM 3
RUN  B-B  200 FOAI  SEA  D91057
(TYPICAL)
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 2 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-25-3381
Work - See page 1 for details.  122 of 213

### Page 16

FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 3 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
123 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 17 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
STA 1920, 1940,  FORWARD CARGO COMPARTMENT
1960, 1980  FORWARD END WALL
INSULATION  INSULATION
BLANKET FLAP  BLANKET FLAP
HALFCAP  TAPE OR  HALFCAP  TAPE OR
TIE WRAP  TIE WRAP
100  120
E •
2)  100
TAPE OR  TAPE OR
TIE WRAP  HALFCAP  TIE WRAP  HALFCAP
TYPICAL  TYPICAL
ARRANGEMENT FOR SYSTEMS PENETRATION
OF FRAME WHEN AN INSULATION BLANKET
FLAP IS PRESENT
C-C
ARRANGEMENT FOR SYSTEMS PENETRATION
OF FRAME WHEN AN INSULATION BLANKET
FLAP IS PRESENT
D-D
SYSTEM 3  2S TAPE OR
RUN  TIE WRAP
TAPE OR  TIE WRAP  3 SYSTEM  RUN
000  SYSTEM RUN
SYSTEM 3
RUN  120O FOAL
E-E  E-E  SEA
EXAMPLE, WHERE FOAM  IS NOT REQUIRED)  EXAMPLE, WHERE FOAM  IS REQUIRED)  D94614
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBEWIRE FOAM SEAL REPLACEMENT
(SHEET 4 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  124 of 213

### Page 18

FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 5 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
125 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 19 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
STA 1920, 1940,  AFT CARGO COMPARTMENT
1960, 1980  FORWARD END WALL
TAPE  TAPE
105
NEW FOAM  NEW FOAM
WRAPPED  WRAPPED*
IN TAPE  IN TAPE
020  100
TAPE  TAPE
→ FWD
TYPICAL ARRANGEMENT FOR
SYSTEMS PENETRATION WHEN AN
INSULATION BLANKET FLAP IS
NOT PRESENT
C-C
TYPICAL ARRANGEMENT FOR
SYSTEMS PENETRATION WHEN AN
INSULATION BLANKET FLAP IS
NOT PRESENT
E-E
TAPE S  SYSTEM
RUN HOSE
SYSTEM 3  12 TAPE OR
RUN  TIE WRAP
3) SYSTEM
RUN
SYSTEM 3
RUN  O000 SEAL
TYPICAL  TYPICAL  BLANKET  D95097
F-F  G-G
ASSEMBLY
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBEWIRE FOAM SEAL REPLACEMENT
(SHEET 6 OF 8)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  126 of 213

### Page 20

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown for parts used in each step are the total number of parts necessary for each step.
For bulk material rolls, the quantity number shown in the first-use step is the total number of rolls provided in
the top kit. The quantity number is not shown in the figure-steps thereafter.
NOTE: If the sidewall linings, ball transfer panel and transport rollers were not removed, refer to
747-400 AMM 25-52-01 and 747-400 AMM 25-53-15 as accepted procedures for removal.
1.
2. The location of the system tube or wire penetrations on the sloping sidewall, shown in this
figure, are typical. Inspect for similar penetrations on the insulation blanket from the left to
right side between STA 1480 and STA 1980. Refer to APPENDIX C for an illustrated visual
aid. Any penetrations through the insulation blankets between the applicable stringer and the
applicable stabilizer angle must be sealed for halon/smoke retention.
3. The location of the system tube or wire penetrations under the floor, shown in this figure, are
typical. Inspect for similar penetrations on the airplane left and right sides, between STA 1920
and STA 1980. Refer to APPENDIX C for an illustrated visual aid. The aft halon/smoke retention
barrier is located at STA 1920 or STA 1980. Any penetrations through the insulation blankets
must be sealed for halon/smoke retention.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to Notes 1 and  2.
(a)(c)(d)
--FOAMInspect1
From around insulation blanket
flap located where tubes or
wires penetrate the insulation.
Refer to Note 2.
--TAPE OR TIE
WRAP
Remove2
From inside the insulation blan-
ket flap. (c)(d)
--FOAMRemove
Surface before the new foam
tape is installed. Use mechani-
cal means to remove debris.
--SYSTEM RUNClean3
Surface before the new foam
tape is installed. Use mechani-
cal means to remove debris.
--INSULATION
BLANKET FLAP
Clean
Around system tubes or wires
to make sure tubes or wires are
separated. Fill all the open
spaces when multiple tubes or
wires pierce the insulation blan-
ket. (b)
-015U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Put/Hold4
From the bulk material roll. Cut
a piece that is 5 inches long, or
cut more if more is required to
make a smoke barrier. (b)
As Re-
quired
015U1780-8 (BMS
1-68, Grade A,
Form III Optional)
FOAM TAPE, 0.5 T
X 2.0 W
Install (New)
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
127 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 21

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Enough from bulk material roll
to wrap around the insulation
blanket flap.
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPECut5
Around insulation blanket flap
and tubes or wires. Make sure
the tape tightly holds the insula-
tion blanket flap so there is no
air space and a smoke barrier
is made. (e)
-BMS 5-146, Type I,
Class 1, Grade A
(BMS 5-157, Type
I, Class 1, Grade A
optional)
TAPEInstall (New)
Identify in the vicinity of re-
placed foam tape that this ser-
vice bulletin was done. Refer to
SOPM 20-50-10 as an accepted
procedure for part marking.
--NEW FOAM TAPEIdentify6
(a) Do a general visual inspection of the AFT cargo compartment area between station 1480 and station
1980. Inspect for foam around system runs. If BMS 8-39 found, remove and replace it with the new
material.
(b) Where system tubes or wires penetrate the insulation blanket, make sure all the space inside the insu-
lation blanket flap is filled with foam tape to create a smoke barrier.
(c) Refer to Table 7 in APPENDIX D for a list of existing part numbers for this Figure.
(d) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
(e) Install tape where BMS 1-68 is used to seal system run penetrations through the insulation blanket. If
there is no blanket flap or tab present, use tape to attach the foam seal to the insulation blanket.
FIGURE 8: AFT CARGO COMPARTMENT SYSTEM TUBE/WIRE FOAM SEAL REPLACEMENT
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
128 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 22 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 7-10, Configuration 1; Group 10, Configuration 2; Group 12-16,
Configuration 1; Group 16, Configuration 2; Group 17, Configuration 1-2; Group 18-19, Configuration 1;
Group 19, Configuration 2.
SEE
1x18
STA  AIR
360  INLET
DUCT
AIR
69฿  INLET
30g
STA
300.57
391
49U
DUCT
PILOTS OVERHEAD ELECTRICAL PANEL
D97067
FIGURE 9: FLIGHT COMPARTMENT OVERHEAD ELECTRICAL EQUIPMENT PANEL FOAM REPLACEMENT
(SHEET 1 OF 4)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  129 of 213

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each step.
NOTE: If the Pilots Electrical Overhead Equipment panel was not removed, refer to that portion in the 747-400
AMM 25-14-01 Drip Shield Removal, 747-400 AMM 31-12-11 and 747-400 AMM 31-12-16 as accepted
procedures.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)(c)1-CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Open1
(a)(c)1-OVERHEAD PAN-
EL INSTL - PI-
LOTS
Open2
(a)(d)-233U3311-5INSULATIONMeasure3
(a)(e)(l)(n)2233U3311-5INSULATIONRemove
(a)(d)-233U3311-9INSULATIONMeasure4
(a)(e)(l)(m)(n)1233U3311-9INSULATIONRemove
(a)(d)-233U3311-25INSULATIONMeasure5
(a)(e)(k)(l)(m)(n)3233U3311-25INSULATIONRemove
(a)(d)-233U3311-14INSULATIONMeasure6
(a)(e)(l)(m)(n)1233U3311-14INSULATIONRemove
(a)(d)-233U3311-7INSULATIONMeasure7
(a)(e)(l)(m)(n)1233U3311-7INSULATIONRemove
(a)(d)-233U3311-18INSULATIONMeasure8
(a)(e)(l)(m)(n)1233U3311-18INSULATIONRemove
Clean structure before insulation
is bonded to the structure. Refer
to 747-400 AMM 20-30-80 as
an accepted procedure.
--CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Clean9
---OVERHEAD PAN-
EL INSTL - PI-
LOTS
Clean
FIGURE 9: FLIGHT COMPARTMENT OVERHEAD ELECTRICAL EQUIPMENT PANEL FOAM REPLACEMENT
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
130 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 24

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
-2233U3311-51INSULATIONInstall (New)10
Cut to 2 pieces.(f)-233U3311-51INSULATIONCut
(a)(g)-233U3311-51INSULATIONBond
(h)-233U3311-51INSULATIONAlign
-1233U3311-53INSULATIONInstall (New)11
(f)-233U3311-53INSULATIONCut
(a)(j)-233U3311-53INSULATIONBond
(h)-233U3311-53INSULATIONAlign
-3233U3311-56INSULATIONInstall (New)12
Cut to 3 pieces.(f)-233U3311-56INSULATIONCut
(a)(j)-233U3311-56INSULATIONBond
(h)-233U3311-56INSULATIONAlign
-1233U3311-54INSULATIONInstall (New)13
(f)-233U3311-54INSULATIONCut
(a)(j)-233U3311-54INSULATIONBond
(h)-233U3311-54INSULATIONAlign
-1233U3311-52INSULATIONInstall (New)14
(f)-233U3311-52INSULATIONCut
(a)(j)-233U3311-52INSULATIONBond
(h)-233U3311-52INSULATIONAlign
-1233U3311-55INSULATIONInstall (New)15
(f)-233U3311-55INSULATIONCut
(a)(j)-233U3311-55INSULATIONBond
(h)-233U3311-55INSULATIONAlign
(i)-747-25-3381 R03SERVICE BUL-
LETIN NUMBER
Apply16
(b)(c)1-OVERHEAD PAN-
EL INSTL - PI-
LOTS
Close17
(b)(c)1-CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Close18
FIGURE 9: FLIGHT COMPARTMENT OVERHEAD ELECTRICAL EQUIPMENT PANEL FOAM REPLACEMENT
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
131 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 25

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) Detach wire bundle(s) from support(s) as needed to gain access to insulated area(s). Do not disconnect
wire bundle connector(s).
(b) Make sure all wire bundles detached for access are attached to same support from which they were
detached.
(c) Overhead Panel Installation may vary from operator to operator.
(d) Measure location and dimensions for use when replacement insulation is installed. The replacement
insulation will cover the area covered by the existing insulation.
(e) Use mechanical means to remove insulation. Refer to APPENDIX A instructions as an accepted proce-
dure for abrasive cleaning
(f) Cut to fit measured dimensions and to have clearance from wire bundle supports, brackets, nutplates
and panels.
(g) Bond to structure. Use BMS 5-123, TYPE I, CLASS 1, CLASS 2, CLASS 3. Refer to SOPM 20-50-12
as an accepted procedure.
(h) Align to measured dimensions as closely as possible before placing it on to structure. Minimize movement
to orient the insulation once it is in contact with the adhesive.
(i) Identify the overhead support assembly in the area of replaced insulation with service bulletin number
747-25-3381 R03 to show that the overhead support assembly is changed. Refer to SOPM 20-50-10
as an accepted procedure.
(j) Bond to structure. Use BMS 5-30, TYPE II, or TYPE III (BMS 5-123 TYPE I, CLASS 1, CLASS 2, or
CLASS 3 OPTIONAL). Refer to SOPM 20-50-12 as an accepted procedure.
(k) Insulation 233U3311-25 is identical to the combined lengths of insulation 233U3311-11 plus QTY 2 of
insulation 233U3311-10 as a single piece of insulation.
(l) Refer to Table 8 in APPENDIX D for a list of existing part numbers for this Figure.
(m) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
(n) To prevent BMS 8-39 Urethane foam particles falling into the circuit breaker terminals below, use a
temporary protective sheet when removing BMS 8-39 Urethane foam from overhead panel support
structure.
FIGURE 9: FLIGHT COMPARTMENT OVERHEAD ELECTRICAL EQUIPMENT PANEL FOAM REPLACEMENT
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
132 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 26 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 7-9, Configuration 1; Group 10, Configuration 2; Group 11-12, 15,
Configuration 1; Group 16-17, Configuration 2; Group 18, Configuration 1; Group 19, Configuration 2.
SEE
2 1
FLIGHT COMPARTMENT
1867970
_ FIGURE 10: FLIGHT COMPARTMENT OVERHEAD PANEL SUPPORT STRUCTURE FOAM REPLACEMENT
(SHEET 1 OF 4)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  133 of 213

### Page 27 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
481
389
STRUCTURE
FWD <  STRUCTURE
→FWD  DRIPSHIELD
E811
DRIPSHIELD
STRUCTURE
STRUCTURE
• FWD
2 FWD
1867990
_ FIGURE 10: FLIGHT COMPARTMENT OVERHEAD PANEL SUPPORT STRUCTURE FOAM REPLACEMENT
(SHEET 2 OF 4)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  134 of 213

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each step.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
-1-CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Open1
-1-OVERHEAD PAN-
EL INSTL - PI-
LOTS
Open2
(c)(d)2232U1497-52FOAM INSULA-
TION
Remove3
(c)(d)2232U1497-53FOAM INSULA-
TION
Remove4
(c)(d)2232U1497-55FOAM INSULA-
TION
Remove5
(c)(d)2232U1497-56FOAM INSULA-
TION
Remove6
(c)(d)2232U1497-57FOAM INSULA-
TION
Remove7
(a)--CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Clean8
(a)--OVERHEAD PAN-
EL INSTL - PI-
LOTS
Clean
-2232U1497-74FOAM INSULA-
TION
Install (New)9
-2232U1497-75FOAM INSULA-
TION
Install (New)10
(b)2232U1497-76FOAM INSULA-
TION
Install (New)11
-2232U1497-77FOAM INSULA-
TION
Install (New)12
-2232U1497-78FOAM INSULA-
TION
Install (New)13
FIGURE 10: FLIGHT COMPARTMENT OVERHEAD PANEL SUPPORT STRUCTURE FOAM REPLACEMENT
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
135 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 29

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
-1-OVERHEAD PAN-
EL INSTL - PI-
LOTS
Close14
-1-CIRCUIT BREAK-
ER AND LIGHT-
PLATE INSTL -
OVERHEAD PAN-
EL
Close15
(a) Clean structure before insulation is installed on the structure. Refer to 747-400 AMM 20-30-80 as an
accepted procedure.
(b) Extend the excess bracket insulation to surrounding dripshield.
(c) Refer to Table 9 in APPENDIX D for a list of existing part numbers for this Figure.
(d) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
FIGURE 10: FLIGHT COMPARTMENT OVERHEAD PANEL SUPPORT STRUCTURE FOAM REPLACEMENT
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
136 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 30 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 7-10, Configuration 1; Group 10, Configuration 2; Group 12-16,
Configuration 1; Group 16, Configuration 2; Group 17, Configuration 1-2; Group 18-19, Configuration 1;
Group 19, Configuration 2.
OVERHEAD
DRIPSHIELD
STA
- 520
230
FLIGHT COMPARTMENT  RBL
LBL  8.5
14.5
STA
320
UP
OVERHEAD DRIPSHIELDS  D97145
(VIEW LOOKING UP AND FWD)
FIGURE 11: FLIGHT COMPARTMENT OVERHEAD DRIPSHIELD FOAM REPLACEMENT
(SHEET 1 OF 3)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  137 of 213

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below for individual parts are the number of parts necessary for each step.
NOTE: Refer to that section in the 747-400 AMM 25-14-01 Drip Shield Removal, 747-400 AMM 31-12-11 and
747-400 AMM 31-12-16 as accepted procedures.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Location and dimensions for use
when replacement insulation is
installed.
-232U1497-54INSULATIONMeasure1
Use mechanical means to re-
move insulation. (a)(b)
3232U1497-54INSULATIONRemove
Clean before insulation is bond-
ed. Refer to 747-400 AMM 20-
30-80 as an accepted proce-
dure.
--FORWARD OVER-
HEAD DRIP-
SHIELD
Clean2
Clean before insulation is bond-
ed. Refer to 747-400 AMM 20-
30-80 as an accepted proce-
dure.
--OVERHEAD DRIP-
SHIELD
Clean
-3232U1497-73FOAM INSULA-
TION
Install (New)3
To fit measured dimensions.-232U1497-73FOAM INSULA-
TION
Cut
To dripshield; Use BMS 5-123,
TYPE I, CLASS 1, CLASS 2, or
CLASS 3. Refer to SOPM 20-
50-12 as an accepted proce-
dure.
-232U1497-73FOAM INSULA-
TION
Bond
To measured dimensions. Mini-
mize movement to orient the in-
sulation once it is in contact with
the adhesive.
-232U1497-73FOAM INSULA-
TION
Align
FIGURE 11: FLIGHT COMPARTMENT OVERHEAD DRIPSHIELD FOAM REPLACEMENT
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
138 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 32

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Enough from bulk material to
cover joins in the foam insula-
tion
-BMS 5-146 TYPE
I, CLASS 1,
GRADE A (BMS 5-
157, TYPE I,
CLASS 1,GRADE
A OPTIONAL)
TAPECut4
Over joins in the foam insula-
tion.
-BMS 5-146 TYPE
I, CLASS 1,
GRADE A (BMS 5-
157, TYPE I,
CLASS 1,GRADE
A OPTIONAL)
TAPEInstall (New)
Identify in the vicinity of re-
placed foam tape that this ser-
vice bulletin was done. Refer to
SOPM 20-50-10 as an accepted
procedure for part marking.
--NEW FOAM TAPEIdentify5
(a) Refer to Table 10 in APPENDIX D for a list of existing part numbers for this Figure.
(b) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
FIGURE 11: FLIGHT COMPARTMENT OVERHEAD DRIPSHIELD FOAM REPLACEMENT
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
139 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 33 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 2-3, 9, 13-14, 16, Configuration 1; Group 16, Configuration 2; Group
17, Configuration 1-2; Group 19, Configuration 1-2.
STA
520
STA
360
STA
240
STA
1480
STA
140
00200000
SEE
000  STA
0000000000  0000000  SEE  2360
STA
1480
p00000000
FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 1 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  140 of 213

### Page 34 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SEE DO
(TYPICAL ALTERNATE
CONFIGURATION)
SEE (D
SEE
TYPICAL BAFFLE
ASSEMBLY CONFIGURATION
D93981
FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 2 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  141 of 213

### Page 35 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
3 FOAM
(2 LOCATIONS)
Q HOLE
(3 LOCATIONS)
STANDOFF  1 FOAM
(3 LOCATIONS)  THICKNESS
1.0 INCH
2) FOAM
1.0 INCH
TYPICAL AIR BAFFLE CONFIGURATION
D94742
FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 3 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  142 of 213

### Page 36

FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 4 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
143 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 37 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SEE BO  FOAM THICKNESS 1  0.75 INCH
(2 LOCATIONS)
FOAM THICKNESS 2  NUTPLATE
(2 LOCATIONS)  0.75 INCH  FOAM 3
NUTPLATE
FOAM (3
TYPICAL ALTERNATE BAFFLE
ASSEMBLY CONFIGURATION
D94615
FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 5 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  144 of 213

### Page 38

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below for individual parts are the number of parts necessary for each step at each air baffle
location.
NOTE: If the side wall linings are not removed, refer to 747-400 AMM 25-59-01 as an accepted procedure for
removal.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--AIR BAFFLEInspect1
Loosen the fasteners which
opens a space between the two
foam pieces.
--AIR BAFFLEOpen
Thickness, which will be either
0.75 inch or 1.00 inch thick.
2-FOAMMeasure2
Length.2-FOAMMeasure3
Locations through the air baffle
and foam pieces.
2-HOLEMeasure4
Hole sizes and locations
through the foam pieces.
--SYSTEM TUBES
AND WIRES
Measure5
That pass between the two
pieces of foam, out of the way,
if possible.
--SYSTEM TUBES
AND WIRES
Move6
Pieces bonded to the air baffle.
(b)(c)(d)
2-FOAMRemove
(a) Do general visual inspection of main deck air baffles left and right sidewalls. Inspect for foam between
air baffles.
(b) When foam is removed, do not abrade adjacent structure that is clad aluminum or has an alodine
coating. If the abrasion penetrates a finish, restore the finish to match adjacent structure.
(c) Refer to Table 11 in APPENDIX D for a list of existing part numbers for this Figure.
(d) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
FIGURE 12: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
145 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 39 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 2-3, 9, 13-14, 16, Configuration 1; Group 16, Configuration 2; Group
17, Configuration 1-2; Group 19, Configuration 1-2.
STA
520
STA
360
STA
STA  0od0  240
1480
STA
140
080000002000
SEE
STA
STA  16000 0000000  0000000000000000  520
2360
SEE
00000000  5000
STA
000000000000000  1480
000000000
D97033
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 1 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  747-25-3381  146 of 213

### Page 40 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
• SEE ®O
TYPICAL
ALTERNATE
CONFIGURATION)
SEE D
OFWD
SEE
TYPICAL BAFFLE
ASSEMBLY CONFIGURATION
D97035
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 2 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  147 of 213

### Page 41 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
DO® FOAM
(2 LOCATIONS)
13 HOLE
(3 LOCATIONS)
STANDOFF
(3 LOCATIONS)
TYPICAL AIR BAFFLE CONFIGURATION
1989552
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 3 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  148 of 213

### Page 42

FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 4 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
149 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 43 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
• SEE DO
1508
FOAM
NUTPLATE
NUTPLATE
1503
FOAM
SEND
TYPICAL ALTERNATE BAFFLE
ASSEMBLY CONFIGURATION
J12130
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 5 OF 7)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  150 of 213

### Page 44

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown for parts used in each step are the total number of parts necessary for each step at each air
baffle location.
For bulk material rolls, the quantity number shown in the first-use step is the total number of rolls provided in
the top kit. The quantity number is not shown in the figure-steps thereafter.
NOTE: If the side wall linings are not removed, refer to 747-400 AMM 25-59-01 as an accepted procedure for
removal.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Replacement foam pieces to
measured length. (a)
2015U1780-9 OR -
10
NEW FOAMMake1
Or similar equipment to cut
0.313 to 0.327 inch diameter
(0.313 inch nominal) holes in
the foam material.
--GASKET HOLE
PUNCH
Get2
With gasket hole punch through
the foam pieces at the locations
measured.
--FASTENER HOLECut3
With sharp knife, in the foam
material, cut an "X" to make
holes the measured size at the
locations measured.
--HOLECut4
Surfaces before the foam pieces
are installed. Refer to 747-400
AMM 20-30-80 as an accepted
procedure.
--AIR BAFFLEClean5
BMS 5-123 TYPE I, CLASS 1,
CLASS 2, or CLASS 3 OPTION-
AL.
-BMS 5-30 TYPE II,
OR TYPE III
ADHESIVEGet6
When the measured foam
thickness is 0.75 inch.
8015U1780-10FOAM 0.75 T X 1.0
W
Install (New)
When the measured foam
thickness is 1.00 inch.
14015U1780-9FOAM 1.0 T X 1.0
W
Install (New)
Pieces to the air baffle within 0.5
inch of each nutplate. Refer to
SOPM 20-50-12 as an accepted
procedure for application of
BMS 5-30, TYPE II, or TYPE III
adhesive (BMS 5-123 TYPE I,
CLASS 1, CLASS 2, or CLASS
3 OPTIONAL).
2015U1780-9 OR -
10
NEW FOAMBond
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
151 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 45

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Install at measured hole loca-
tions cut in the air baffle foam
pieces. Make sure that there is
no potential for wire chafing.
Refer to SWPM 20-10-11and,
SWPM 20-10-19.
--SYSTEM TUBES
AND WIRES
Align7
Tighten the air baffle fasteners.--AIR BAFFLEClose
Identify in the vicinity of re-
placed foam tape that this ser-
vice bulletin was done. Refer to
SOPM 20-50-10 as an accepted
procedure.
--NEW FOAM TAPEIdentify8
(a) Select 015U1780-10 foam roll when foam thickness is 0.75 inch. Select 015U1780-9 foam roll when
foam thickness is 1.0 inch.
FIGURE 13: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
152 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 46 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
I This Figure applies only to: Group 4-5, Configuration 1.
STA
520
STA
360
RIGHT SIDE
DADO PANELS
SEE
STA
1480
STA
140
LEFT SIDE DADO
PANELS
SEE
STA
520  0000009 00002  STA
2360
RIGHT SIDE
DADO PANELS
SEE
10000
STA
1480
LEFT SIDE
DADO PANELS
SEE 1
200000000
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 1 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  153 of 213

### Page 47 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SEE DO
AIR BAFFLE
¡SEE DOO
AIR BAFFLE
SEE OO
SEE ® O  AIR BAFFLE
AIR BAFFLE
• SEE DO
AIR BAFFLE
SEE
AIR BAFFLE
SEE ® C
AIR BAFFLE  SEE  UP
AIR BAFFLE
TYPICAL AIR BAFFLES
U60261
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 2 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  1888-97-1+L
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  154 of 213

### Page 48 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
FASTENER HOLE
(2 LOCATIONS)
FOAM
| (2 LOCATIONS)
FOAM
NUTPLATES
(2 LOCATIONS)
OR
NUTPLATES
(TYPICAL)
TYPICAL FOAM REPLACEMENT
AIR BAFFLE
(TYPICAL OPPOSITE
ORIENTATION)
INSERTS
PHENOLIC
BLOCKS
NO REWORK REQUIRED
FOR AIR BAFFLES
WITH PHENOLIC BLOCKS
U60262
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 3 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  155 of 213

### Page 49 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SPACER
(3 LOCATIONS)
- NUT
(3 LOCATIONS)
FOAM
OR
INSERT,
) FASTENER
) FOAM
INSERT,
FASTENER
INSERT,
+ FASTENER
TYPICAL FOAM REPLACEMENT
AIR BAFFLE
U60263
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 4 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-25-3381
Work - See page 1 for details.  156 of 213

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below for individual parts are the number of parts necessary for each step at each air baffle
location.
NOTE: If the side wall linings were not removed, refer to 747-100/200/300 AMM 25-59-00 as an accepted
procedure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--AIR BAFFLEInspect1
Loosen fasteners that open a
space between the two foam
pieces.
--AIR BAFFLEOpen
Thickness can be 0.75 inch or
1.00 inch.
2-FOAMMeasure2
Length.2-FOAMMeasure3
Locations through the air baffle
and foam pieces.
2-FASTENER HOLEMeasure4
Hole sizes and locations
through the foam pieces.
--SYSTEM RUNMeasure5
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
157 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 51

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
That pass between the two
pieces of foam, out of the way
if possible.
--SYSTEM RUNMove6
Pieces bonded to the air baffle.
(b)(c)(d)
2-FOAMRemove
(a) Do a general visual inspection of main deck air baffles, left and right sidewalls. inspect for BMS 8-39
foam between the air baffles.
(b) When foam is removed, do not abrade structure that is clad aluminum or has an alodine coating. If the
abrasion penetrates a finish, restore the finish to match adjacent structure.
(c) Refer to Table 12 in APPENDIX D for a list of existing part numbers for this Figure.
(d) Refer to APPENDIX C for descriptions and example photographs of BMS 8-39 to aid in the identification
and removal of the existing BMS 8-39 foam.
FIGURE 14: MAIN DECK AIR BAFFLE FOAM INSPECTION AND REMOVAL, LEFT/RIGHT SIDEWALLS
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
158 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 52 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
• This Figure applies only to: Group 4-5, Configuration 1.
STA
520
STA
360
RIGHT SIDE
DADO PANELS
SEE
STA
1480
STA
140
LEFT SIDE DADO
PANELS
SEE
STA
520  000000g 0000  STA
2360
RIGHT SIDE
DADO PANELS
SEE
10000
STA
1480
LEFT SIDE
DADO PANELS
SEE L
600000000
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 1 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  159 of 213

### Page 53 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SEE DO
AIR BAFFLE
SEE DO
AIR BAFFLE
SEE DO
AIR BAFFLE
SEE DO
AIR BAFFLE
• SEE ®O
AIR BAFFLE
SEE
AIR BAFFLE
SEE B
AIR BAFFLE  SEE DO  UP
AIR BAFFLE
U60266
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 2 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-25-3381
Work - See page 1 for details.  160 of 213

### Page 54 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
SPACER
(3 LOCATIONS)
NUT
(3 LOCATIONS)
OR
NUTPLATE
...
TYPICAL FOAM REPLACEMENT
AIR BAFFLE
U60271
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 3 OF 6)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  161 of 213

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown for parts used in each step are the total numbers of parts necessary for each step at each air
baffle location.
For bulk material rolls, the quantity number shown in the first-use step is the total number of rolls provided in
the top kit.
NOTE: If the side wall linings were not removed, refer to 747-100/200/300 AMM 25-59-00 as an
accepted procedure for removal.
1.
2. The number of air baffles installed in the airplane, the length, and the thickness of the foam
pieces can vary significantly between airplanes. For this reason, Top Kit 015U1780-15 contains
the maximum requirement. Any excess quantity should be returned to the operators spares
store. The operator may order parts individually instead of ordering the entire kit.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Replacement pieces to mea-
sured length. (a)
--NEW FOAMMake1
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 4 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
162 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 56

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Use Gasket Hole Punch or sim-
ilar equipment to cut 0.313 to
0.343 inch diameter (0.313 inch
nominal) holes in the foam ma-
terial.
--GASKET HOLE
PUNCH
Get2
Use gasket hole punch to cut
fastener hole through the foam
pieces at the locations mea-
sured.
--FASTENER HOLECut3
With sharp knife, cut an "X" to
make holes the measured size
at the locations measured.
--HOLESCut4
Clean surfaces before the foam
pieces are installed. Refer to
747-100/200/300 AMM 20-30-
80 as an accepted procedure.
--AIR BAFFLEClean5
-BMS 5-30, TYPE II,
OR TYPE III (BMS
5-123 TYPE I,
CLASS 1, CLASS
2, or CLASS 3 OP-
TIONAL)
ADHESIVEGet6
Install when the measured foam
thickness is 0.75 inch.
10015U1780-17FOAM 0.75 T X
1.05 W
Install (New)
Install when the measured foam
thickness is 1.00 inch.
1015U1780-16FOAM, 1.0 T X
1.05 W
Install (New)
Bond replacement pieces to the
air baffle. When nutplates are
present, bond within 0.50 inch
of each nutplate. Refer to
SOPM 20-50-12 as an accepted
procedure for application of
BMS 5-30, TYPE II, or TYPE III
adhesive (BMS 5-123 TYPE I,
CLASS 1, CLASS 2, or CLASS
3 OPTIONAL).
--NEW FOAM TAPEBond
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
163 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 57

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Install at measured hole loca-
tions cut in the air baffle foam
pieces. Make sure that there is
no potential for wire chafing.
Refer to SWPM 20-10-
11andSWPM 20-10-19 as ac-
cepted procedures.
--SYSTEM RUNAlign7
Tighten the air baffle fasteners.--AIR BAFFLEClose
(a) Select 015U1780-17 foam roll when foam thickness is 0.75 inch. Select 015U1780-16 foam roll when
foam thickness is 1.0 inch. Both part numbers have a width of 1.05 inches.
FIGURE 15: MAIN DECK AIR BAFFLE FOAM INSTALLATION, LEFT/RIGHT SIDEWALLS
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: August 19, 2010
747-25-3381Revision 3 February 19, 2021
164 of 213
BOEING SERVICE BULLETIN 747-25-3381

### Page 58 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
This Figure applies only to: Group 1-3, 6-10, Configuration 1; Group 10, Configuration 2; Group 11-16,
Configuration 1; Group 16, Configuration 2; Group 17, Configuration 1-2; Group 18-19, Configuration 1;
Group 19, Configuration 2.
SEE 1 THROUGH H
. FRAME
30
CAPSTRIP
ASSEMBLY
DUCT
BRACKET
INBD  (TYPICAL)
23
• IML SKIN
- FRAME
FRAME
FOAM
PAD •
INBD
*CAPSTRIP
(TYPICAL)  A-A  ASSEMBLY
FIGURE 16: CROWN AREA - FOAM PAD REMOVAL
(SHEET 1 OF 5)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-25-3381
Work - See page 1 for details.  165 of 213

### Page 59 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
FRAME  / SKIN
SKIN ~
CAPSTRIP
ASSEMBLY
FRAME
CAPSTRIP
ASSEMBLY
CENTER STOWAGE
SUPPORT INSTL  230
CEILING
(TYPICAL)  SUPPORT
SKIN
FRAME
CAPSTRIP
ASSEMBLY
SKIN
FRAME
CAPSTRIP
ASSEMBLY
CENTER STOWAGE
SUPPORT INSTL  • TENSION
(TYPICAL)  TIE SUPPORT
(TYPICAL)
FIGURE 16: CROWN AREA - FOAM PAD REMOVAL
(SHEET 2 OF 5)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  747-25-3381
Work - See page 1 for details.  166 of 213

### Page 60 (OCR)

BOEING SERVICE BULLETIN 747-25-3381
CONTROL CABLE SUPPORT
(TYPICAL)
RECIRCULATION FAN
(TYPICAL)
1868241
FIGURE 16: CROWN AREA - FOAM PAD REMOVAL
(SHEET 3 OF 5)
Original Issue: August 19, 2010
Revision 3 February 19, 2021  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  747-25-3381  167 of 213

The text continues at https://openairdocs.org/service-documents/boeing/sb-747-25-3381/file/9df69edca9eb.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
