# Boeing Special Attention Service Bulletin 747-34-2925: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-1041; AD 2013-19-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 747-34-2925](https://openairdocs.org/service-documents/boeing/sb-747-34-2925.md)
- Title as filed: U.S. DOT/FAA - Service Information - 3
- Pages: 26
- PDF: https://openairdocs.org/files/sha256/71/54/715426f2d35604736adc4061302518cfbe1eb900cc0dbee39f61f981f76545a8
- Page: https://openairdocs.org/service-documents/boeing/sb-747-34-2925/file/715426f2d356

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial        
Airplane
Group 
 747
Service Bulletin
SPECIAL ATTENTION
Number: 747-34-2925
Date: June 04, 2008
ATA System: 2732 3412
SUBJECT: NAVIGATION - Stall Warning System - Angle of Airflow Sensor Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2008 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P .O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, MD-10, MD-11, MD-80, MD-88, MD-90, and the Boeing livery are all trademarks
owned by The Boeing Company; and no trademark license is granted in connection with this document unless
provided in writing by Boeing.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
1 of 26
2.0

### Page 2

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
2 of 26
BOEING SERVICE BULLETIN 747-34-2925
BLANK PAGE

### Page 3

Table of Contents
Summary ..................................................... 5
1. PLANNING INFORMATION ......................................... 7
A. Effectivity ................................................ 7
1. Airplanes ............................................. 7
2. Spares Affected ........................................ 1 5
B. Concurrent Requirements ...................................... 1 5
C. Reason ................................................ 1 6
D. Description .............................................. 1 6
E. Compliance .............................................. 1 7
F . Approval ............................................... 1 7
G. Manpower .............................................. 1 7
H. Weight and Balance Changes .................................... 1 8
I. Electrical Load Data ......................................... 1 8
J. References .............................................. 1 8
1. Existing Data .......................................... 1 8
2. Data supplied with this Service Bulletin ............................ 1 9
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 1 9
K. Publications Affected ......................................... 1 9
L. Interchangeability and Intermixability of Parts ........................... 1 9
2. MATERIAL INFORMATION ........................................ 2 1
A. Material - Price and Availability ................................... 2 1
B. Industry Support Information .................................... 2 1
C. Parts Necessary For Each Airplane ................................. 2 1
1. Kits/Parts ............................................ 2 1
2. Parts and Materials Supplied by the Operator ........................ 2 1
3. Parts Modified and Reidentified ................................ 2 1
4. Parts Removed and Not Replaced .............................. 2 1
D. Parts Necessary to Change Spares ................................. 2 1
E. Special Tooling - Price and Availability ............................... 2 2
F . Special Tooling Necessary to do this Service Bulletin ....................... 2 2
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 3
A. GENERAL INFORMATION ..................................... 2 3
B. WORK INSTRUCTIONS ....................................... 2 3
FIGURE 1: ANGLE OF AIRFLOW SENSOR - INSPECTION ....................... 2 6
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
3 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 4

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
4 of 26
BOEING SERVICE BULLETIN 747-34-2925
BLANK PAGE

### Page 5

Commercial        
Airplane
Group 
 747
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 747-34-2925Date: June 04, 2008
ATA System: 2732 3412
SUBJECT: NAVIGATION - Stall Warning System - Angle of Airflow Sensor Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATEL Y .
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This service bulletin gives instructions for a one-time inspection of Conrac/Ametek/Gulton Angle of Airflow (AOA)
sensors with part numbers 2566A21/A30 (10-60878-3/-4) for 747-100/200/300 airplanes and part numbers
2566A40S (S233T913-2) for 747-400 airplanes. This inspection will do a check for a misalignment between the
AOA sensor shaft and the sensor synchro transmitter. This misalignment is caused by a defective set screw
condition.The airplane could have incorrect control column shaker activation if the inspection given in this service
bulletin is not accomplished.
One 747-400 operator reported a control column shaker activation on takeoff. The control column shaker
activation continued while the airplane was in flight and EICAS messages ALT DISAGREE and IAS DISAGREE
were displayed. The flight crew used the alternative Air Data Computer (left ADC) and the altitude and airspeed
indications cancelled. After landing the right ADC was replaced. On the subsequent flight the control column
shaker operated again at takeoff and the flight crew had to do a Rejected Takeoff (RTO). Troubleshooting steps
found that the right AOA sensor was unserviceable.
The inspection of the AOA sensor showed that the set screw connected to the synchro transmitter was not
correctly attached to the AOA sensor shaft. Accomplishment of this service bulletin will stop incorrect control
column shaker activation.
Boeing Service Related Problem (SRP) 747-SRP-34-0114 is related to this service bulletin.
Fleet Team Digest (FTD) 747 FTD 34-07001 is related to this service bulletin.
ACTION
Part 1: Do a visual inspection of the AOA sensors. If an AOA sensor is found to be a Conrac/Ametek/Gulton
sensor, do Part 2 of the service bulletin.
Group 1:
Part 2: Do a test of the AOA sensor. If the AOA sensor fails to activate the control column shaker, do Part 3 of
the service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
5 of 26

### Page 6

Group 2:
Part 2: Do a test of the AOA sensor. If the AOA sensor fails the test, replace the AOA sensor.
Group 1:
Part 3: Do an Aircraft Maintenance Manual (AMM) Operational Test of the Stall Warning System. If the AOA
sensor fails to activate the control column shaker, replace the AOA sensor.
NOTE: New part is only necessary if the inspection and test indicate that the existing sensor must be replaced.
EFFECTIVITY
747-100/100B/100B SUD/200B/200C/200F/300/400/400D/400F/747SP/747SR Airplanes. Refer to Paragraph
1.A., Effectivity, Airplanes for the list of affected airplanes.
COMPLIANCE
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
6 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 7

Commercial        
Airplane
Group 
 747
Service Bulletin
SPECIAL ATTENTION
Number: 747-34-2925
Date: June 04, 2008
ATA System: 2732 3412
SUBJECT: NAVIGATION - Stall Warning System - Angle of Airflow Sensor Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATEL Y .
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D6-30300 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
747-100/200/300 airplanes that require different Angle of Airflow
(AOA) sensor inspection
-1
747-400 airplanes that require different Angle of Airflow (AOA) sensor
inspection
-2
Airplane Models:
747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F , 747-300, 747-400, 747-400D,
747-400F , 747SP , 747SR
GroupVariable Number
1RA001 - RA034
1RA101 - RA115
1RA161 - RA164
1RA201 - RA203
1RA216 - RA217
1RA245 - RA246
1RA251 - RA266
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
7 of 26

### Page 8

GroupVariable Number
1RA301 - RA318
1RA351 - RA360
1RA369 - RA373
1RA401 - RA418
1RA501 - RA502
1RA521 - RA528
1RA532 - RA548
1RA551 - RA552
1RA559 - RA561
1RA581 - RA582
1RA585
1RA601 - RA602
1RA631 - RA635
1RA651 - RA652
1RA671 - RA677
1RA701 - RA702
1RA721 - RA731
1RA741 - RA745
1RA749 - RA750
1RA761 - RA762
1RA781 - RA784
1RA901 - RA916
1RB001 - RB016
1RB041 - RB044
1RB071 - RB075
1RB101 - RB102
1RB411 - RB413
1RB421
1RB601 - RB607
1RB681 - RB697
1RB711
1RB721 - RB723
1RB741 - RB748
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
8 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 9

GroupVariable Number
1RD001 - RD004
1RD021 - RD022
1RD041 - RD059
1RD071 - RD072
1RD081 - RD083
1RD091 - RD092
1RD101 - RD104
1RD121 - RD127
1RD131 - RD144
1RD166 - RD167
1RD171 - RD172
1RD181 - RD183
1RD201 - RD204
1RD221 - RD227
1RD231 - RD235
1RD241 - RD243
1RD251 - RD262
1RD271 - RD272
1RD291 - RD292
1RD301 - RD302
1RD311
1RD351 - RD358
1RD361 - RD366
1RD381 - RD383
1RD411 - RD414
1RD421 - RD426
1RD431 - RD435
1RD441 - RD442
1RD451 - RD456
1RD461
1RD471 - RD475
1RD513 - RD519
1RD531 - RD533
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
9 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 10

GroupVariable Number
1RD551
1RD561
1RD571
1RD581 - RD583
1RD591 - RD593
1RD601 - RD607
1RD621 - RD623
1RD641 - RD649
1RD651 - RD659
1RD661
1RD671
1RD681 - RD682
1RD691 - RD692
1RD701 - RD702
1RD721 - RD722
1RD741 - RD742
1RD751 - RD755
1RD761
1RD771 - RD775
1RD781 - RD783
1RD791 - RD792
1RE001
2RF001 - RF006
1RG001 - RG009
1RG091
1RG095
1RG101 - RG104
1RG121 - RG126
1RG141 - RG142
1RG161 - RG164
1RG171 - RG174
1RG191 - RG193
1RG211 - RG213
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
10 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 11

GroupVariable Number
1RG221 - RG222
1RH101 - RH102
1RH111 - RH112
1RH121 - RH122
1RJ131 - RJ133
1RJ151 - RJ152
1RJ301 - RJ303
1RJ321 - RJ322
1RJ331 - RJ333
2RL401 - RL403
2RL411 - RL436
2RL451 - RL456
2RL461 - RL462
2RL471 - RL475
2RL481
2RL491 - RL492
2RL501 - RL502
2RL511 - RL515
2RL521 - RL522
2RL531 - RL533
2RL561 - RL562
2RL576
2RL651 - RL655
2RL671 - RL675
2RL681 - RL684
2RL751 - RL752
2RM001 - RM007
2RM010 - RM013
2RM021 - RM024
2RM026 - RM030
2RM036 - RM045
2RM051 - RM053
2RM071
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
11 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 12

GroupVariable Number
2RM081 - RM084
2RM091
2RM096 - RM097
2RM116 - RM117
2RM126 - RM132
2RM136 - RM147
2RM156 - RM158
2RM166 - RM177
2RM191 - RM192
2RM231 - RM233
2RM241 - RM246
2RM261 - RM264
2RM316 - RM318
2RM331 - RM333
2RM341
2RM351 - RM355
2RM366 - RM367
2RM401 - RM403
2RM426
2RM431
2RM441 - RM443
2RM445
2RM801 - RM803
2RM811 - RM813
2RM851 - RM859
2RM861 - RM863
2RM871 - RM899
2RM901 - RM906
2RM911
1RR001 - RR005
1RR021 - RR025
1RR031
1RR201 - RR206
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
12 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 13

GroupVariable Number
1RR221 - RR226
1RR261 - RR267
1RR301 - RR310
1RR331 - RR332
1RR336
1RR341 - RR345
1RR361 - RR362
1RR421 - RR422
1RR431 - RR432
1RR441 - RR442
1RR451
1RR501 - RR504
1RR521 - RR522
1RR526
1RR531
1RR551 - RR556
1RR561
1RR566
2RR701
2RR721 - RR724
2RR746 - RR748
2RR851 - RR856
2RR861 - RR862
2RR951 - RR952
1RS001 - RS002
1RS201
1RS211 - RS212
1RS221 - RS222
1RS231 - RS241
1RS251 - RS259
1RS263
1RS265 - RS268
1RS271 - RS276
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
13 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 14

GroupVariable Number
1RS291 - RS292
1RS301 - RS306
1RS311 - RS320
1RS331 - RS333
1RS341 - RS342
1RS699
1RS701 - RS703
1RS711 - RS713
1RS721 - RS722
1RS741 - RS743
1RS751 - RS752
1RS761 - RS762
1RS771
1RS781 - RS782
1RS786
2RT001 - RT014
2RT021 - RT022
2RT031 - RT035
2RT041 - RT047
2RT061
2RT071 - RT075
2RT101 - RT103
2RT121
2RT131 - RT137
2RT151 - RT152
2RT161 - RT168
2RT401 - RT412
2RT431 - RT447
2RT451 - RT469
2RT471 - RT499
2RT501 - RT535
2RT551 - RT568
2RT571 - RT591
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
14 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 15

GroupVariable Number
2RT601 - RT657
2RT671 - RT673
2RT681 - RT682
2RT691 - RT699
2RT701 - RT704
2RT711 - RT717
2RT741 - RT757
2RT776 - RT777
2RT781 - RT784
2RT801 - RT803
2RT811 - RT814
2RT831 - RT837
2RT861 - RT864
2RT876 - RT880
2RT931 - RT932
2RT945 - RT949
2RT951 - RT955
2RT966 - RT967
2RU001 - RU006
2RU016 - RU017
2RU031 - RU032
2RU051 - RU052
2RU059 - RU062
2RU081 - RU083
2RU101 - RU102
2RU121 - RU132
2RU801 - RU809
2RU831 - RU841
2. Spares Affected
None.
B. Concurrent Requirements
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
15 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 16

C. Reason
This service bulletin gives instructions for a one-time inspection of Conrac/Ametek/Gulton Angle of
Airflow (AOA) sensors with part numbers 2566A21/A30 (10-60878-3/-4) for 747-100/200/300 airplanes
and part numbers 2566A40S (S233T913-2) for 747-400 airplanes. This inspection will do a check for
a misalignment between the AOA sensor shaft and the sensor synchro transmitter. This misalignment
is caused by a defective set screw condition. The airplane could have incorrect control column shaker
activation if the inspection given in this service bulletin is not accomplished.
One 747-400 operator reported a control column shaker activation on takeoff. The control column
shaker activation continued while the airplane was in flight and EICAS messages ALT DISAGREE and
IAS DISAGREE were displayed. The flight crew used the alternative Air Data Computer (left ADC) and
the altitude and airspeed indications cancelled. After landing the right ADC was replaced. On the
subsequent flight the control column shaker operated again at takeoff and the flight crew had to do a
Rejected Takeoff (RTO). Troubleshooting steps found that the right AOA sensor was unserviceable.
The inspection of the AOA sensor showed that the set screw connected to the synchro transmitter was
not correctly attached to the AOA sensor shaft. Accomplishment of this service bulletin will stop incorrect
control column shaker activation.
Boeing Service Related Problem (SRP) 747-SRP-34-0114 is related to this service bulletin.
Fleet Team Digest (FTD) 747 FTD 34-07001 is related to this service bulletin.
D. Description
Part 1: Do a visual inspection of the AOA sensor. If the AOA sensor is found to be a
Conrac/Ametek/Gulton sensor, do Part 2 of the service bulletin.
Group 1:
Part 2: Do a test of the AOA sensor. If the AOA sensor fails to activate the control column shaker, do
Part 3 of the service bulletin.
Group 2:
Part 2: Do a test of the AOA sensor. If the AOA sensor fails the test, replace the AOA sensor.
Group 1:
Part 3: Do an Aircraft Maintenance Manual (AMM) Operational Test of the Stall Warning System. If the
AOA sensor fails to activate the control column shaker, replace the AOA sensor.
NOTE: New part is only necessary if the inspection and test indicate that the existing sensor must be
replaced.
Group 1:
Affected Maintenance Zones
ZoneModel
113, 114747-100, 747-100B, 747-100B
SUD, 747-200B, 747-200C,
747-200F , 747-300, 747SP ,
747SR
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
16 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 17

Group 2:
Affected Maintenance Zones
ZoneModel
211, 212747-400, 747-400D, 747-400F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin.The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the inspection given in this service bulletin be done within 36 months after
the date on this service bulletin.
If an AOA check (such as Maintenance Planning Document (MPD) Task 4-27-0160 for 747-100/200/300
operators or an equivalent task for 747-400 operators associated with a 'C' check) has been
accomplished within the last 15 months or if one is scheduled within the compliance time, it can take
the place of the required check and the service bulletin is considered accomplished.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA).The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each sensor.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
17 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 18

PART 1
Elapsed HoursTask HoursNumber of
Persons
Task
0.100.101Inspection
0.100.10TOTAL FOR EACH SENSOR
PART 2
Elapsed HoursTask HoursNumber of
Persons
Task
0.250.502Test
0.250.50TOTAL FOR EACH SENSOR
Group 1:
PART 3
Elapsed HoursTask HoursNumber of
Persons
Task
0.250.502Test
0.250.50TOTAL FOR EACH SENSOR
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. 747-100/200/300 Maintenance Planning Data (MPD) Task 4-27-0160
a. Boeing Service Related Problem (SRP) 747-SRP-34-0114
b. 747 Fleet Team Digest (FTD) 34-07001
c. 747-100/200/300 Aircraft Maintenance Manual (AMM) 24-22-00, 27-32-00, 27-32-01, 27-51-00
d. 747-400 Aircraft Maintenance Manual (AMM) 24-22-00, 34-12-03
e. 747-100/200/300 Maintenance Planning Data (MPD) Task 4-27-0160
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
18 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 19

2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
None.
K. Publications Affected
None.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
19 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 20

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
20 of 26
BOEING SERVICE BULLETIN 747-34-2925
BLANK PAGE

### Page 21

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the configuration changes inspection given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number /
Specification
(a) (b) (c) (d)Angle of Attack Sensor12566A21 or
2566A30
(10-60878-3 or
10-60878-4)
(a) (b) (c) (e)Angle of Attack Sensor12566A40S or
S233T913-2
(a) Each airplane has 2 stall warning system angle of attack sensors installed.
(b) This part is only necessary if the inspection and tests indicate the existing sensor must
be replaced.
(c) Ametek Aerospace (V92627), 1644 Whittier Ave, Costa Mesa, California 92627-4415.
(d) For 747-100/200/300 airplanes.
(e) For 747-400 airplanes.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
21 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 22

E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
22 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 23

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s)
give the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to ensure visual access to all surfaces in the
inspection area. This level of inspection is made under normal available lighting
conditions such as daylight, hangar lighting, flashlight or drop-light and may require
removal or opening of access panels or doors. Stands, ladders or platforms may be
required to gain proximity to the area being checked.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "as
given in" are included in the instruction, the procedure in the Boeing document must
be used.
B. WORK INSTRUCTIONS
PART 1: ANGLE OF AIRFLOW (AOA) SENSOR
1. Do a General Visual Inspection of the AOA sensors as given in FIGURE 1.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
23 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 24

a. If an AOA sensor is a Conrac/Ametek/Gulton AOA sensor with a paddle type vane is installed,
do PART 2: TEST THE STALL WARNING SYSTEM for that sensor.
b. If a BF Goodrich/Rosemount AOA sensor with a swept vane is installed, no more work is
necessary.
Group 1:
PART 2:TEST THE STALL WARNING SYSTEM
1. Supply electrical power to the airplane. Refer to 747-100/200/300 AMM 24-22-00 as an accepted
procedure.
2. Make sure the applicable circuit breakers for the Stall Warning System are closed. Refer to
747-100/200/300 AMM 27-32-00 as an accepted procedure.
3. At the P5 Overhead panel, move the stall warning HTR OFF-NORMAL-TEST switch to HTR OFF
position.
4. Move the trailing edge flaps to the 30 detent position. Refer to 747-100/200/300 AMM 27-51-00
as an accepted procedure.
WARNING: SUFFICIENT TIME MUST BE ALLOWED FOR SENSOR VANES TO COOL BEFORE
CONTINUING TEST. VANES MAY BE HOT ENOUGH TO CAUSE BURNS.
CAUTION: VANES MUST NOT BE SPUN. DAMAGE TO SYNCHROS COULD OCCUR.
5. Make sure the AOA sensors are at the horizontal position.
6. Move the left AOA sensor vane trailing edge up from the zero degrees position to approximately
24 degrees (7.5 degrees position on the AOA sensor scale).
7. On the flight deck, make sure the control column shaker is activated within a tolerance of +/-1
degree.
a. If the control column shaker is activated, no more work is necessary. Put the airplane back
to a serviceable condition.
b. If the control column shaker is not activated, do Part 3: Operational Test of the Stall Warning
System.
8. If necessary, repeat steps 6. and 7. again for the right AOA sensor.
Group 1:
PART 3: OPERATIONAL TEST OF THE STALL WARNING SYSTEM
1. Do an Operational Test of the Stall Warning System. Refer to 747-100/200/300 AMM 27-32-00
as an accepted procedure.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
24 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 25

a. If the AOA sensor fails to activate the control column shaker in this operational test, replace
the AOA sensor. Refer to 747-100/200/300 AMM 27-32-01 as an accepted procedure.
2. Put the airplane back to a serviceable condition.
Group 2:
PART 2:TEST THE STALL WARNING SYSTEM
1. Supply electrical power to the airplane. Refer to 747-400 AMM 24-22-00 as an accepted procedure.
2. Make sure the applicable circuit breakers for the Stall Warning System are closed. Refer to 747-400
AMM 34-12-03 as an accepted procedure.
3. Open and attach DO-NOT -CLOSE tags to the circuit breakers for the Left and Right AOA heaters.
Refer to 747-400 AMM 34-12-03 as an accepted procedure.
WARNING: DO NOT TOUCH THE AOA SENSOR WHEN THE SENSOR HEAT IS ON.YOU CAN
BURN YOURSELF ON THE AOA SENSOR.
4. Attach an angular displacement tool to the AOA sensor vane to be tested.
5. Connect an ARINC 429 bus reader to the Air Data Computer (ADC) test connector (the left ADC
for the left AOA sensor, the right ADC for the right AOA sensor).
NOTE: The "HI" pin is on the left of the "TEST ONL Y" connector and the "LO" pin is on the right
of the test connector.
6. Move the angular displacement tool on the AOA vane to the values given in the table that follows:
NOTE: Make sure the data bus reader shows the values on the table that follows in decimal
format.
NOTE: A positive angle of attack is produced when the trailing edge of the AOA vane is above
the horizontal axis.
ADC TEST
OCTAL LABEL 221, 222 and 223 OUTPUTVANE POSITION
0 Degrees +/- 0.750 Degrees
+10 Degrees +/- 0.75+10 Degrees
-10 Degrees +/- 0.75-10 Degrees
7. If you cannot get the values given in the table, replace the AOA sensor. Refer to 747-400 AMM
34-12-03 as an accepted procedure.
8. If necessary do steps 4. thru 7. to test the other AOA sensor.
9. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
June 04, 2008
747-34-2925
25 of 26
BOEING SERVICE BULLETIN 747-34-2925

### Page 26 (OCR)

BOEING SERVICE BULLETIN 747-34-2925
PADDLE-TYPE  SWEPT VANE
VANE
CONRAC/AMETEK/GULTON SENSOR  BF GOODRICH/ROSEMOUNT SENSOR
(INSPECTION REQUIRED)  (INSPECTION NOT REQUIRED)
LEFT ANGLE OF AIRFLOW (AOA) SENSOR  (RIGHT AOA SENSOR IS EQUIVALENT)  1548459
FIGURE 1: ANGLE OF AIRFLOW SENSOR - INSPECTION
(SHEET 1 OF 1)
June 04, 2008
747-34-2925
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  26 of 26

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
