# Boeing Special Attention Service Bulletin 747-35-2133: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0489; AD 2018-23-13 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 747-35-2133](https://openairdocs.org/service-documents/boeing/sb-747-35-2133.md)
- Title as filed: SB 747-35-2133-01--
- Pages: 25
- PDF: https://openairdocs.org/files/sha256/84/7c/847c033baf985f1522cedeb6277fa52190234d6154c484f914b4860e503ed99e
- Page: https://openairdocs.org/service-documents/boeing/sb-747-35-2133/file/847c033baf98

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
747
Service Bulletin
SPECIAL ATTENTION
Number: 747-35-2133
Original Issue: October 13, 2017
Revision 1: November 01, 2017
ATA System: 3511
SUBJECT: OXYGEN - Crew Oxygen System - Crew Oxygen Mask/Regulator and Stowage Box
Change
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2017 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
1 of 25
2.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
2 of 25
BOEING SERVICE BULLETIN 747-35-2133
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 15
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 18
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FIGURE 1: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
FIGURE 2: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
3 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
4 of 25
BOEING SERVICE BULLETIN 747-35-2133
BLANK PAGE

### Page 5

Commercial 
Airplanes
747
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 747-35-2133Original Issue: October 13, 2017
Revision 1: November 01, 2017
ATA System: 3511
SUBJECT: OXYGEN - Crew Oxygen System - Crew Oxygen Mask/Regulator and Stowage Box
Change
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Airplanes in the effectivity of this service bulletin must do 747-35-2133 R01. The Original Issue of this Service
Bulletin was an administrative release and was not published on My Boeing Fleet (MBF).
REASON FOR REVISION
SB 747-35-2133 Revision 1 is the initial publication of the Service Bulletin to the 747 Fleet. This revision constitutes
a complete issue.
REVISION HISTORY
October 13, 2017Original Issue:
November 01, 2017Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
5 of 25

### Page 6

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
6 of 25
BOEING SERVICE BULLETIN 747-35-2133
BLANK PAGE

### Page 7

Commercial 
Airplanes
747
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 747-35-2133Original Issue: October 13, 2017
Revision 1: November 01, 2017
ATA System: 3511
SUBJECT: OXYGEN - Crew Oxygen System - Crew Oxygen Mask/Regulator and Stowage Box
Change
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will let crew members remove crew oxygen masks/regulators from the
stowage boxes without the occurrence of a harness caught in the face piece or goggles. If this service bulletin
is not done, a harness could get caught in the face piece or goggles and increase the time to put on the crew
oxygen masks/regulators, which may lead to hypoxia and the loss of useful consciousness, resulting in loss of
control of the airplane.
During flight tests crew oxygen masks/regulators did not function as designed, as users could not put the crew
oxygen masks/regulators on quickly. The crew oxygen mask/regulator took longer to put on because the harness
tubing became caught in the face piece. This condition causes a delay for the flight crew to put on the mask(s),
which may lead to hypoxia and the loss of useful consciousness, resulting in a loss of control of the airplane.
As a solution to this problem, the manufacturer has changed the design of the crew oxygen mask/regulator and
the stowage box to prevent the occurrence of a harness that could get caught in the face piece or goggles before
the crew oxygen mask/regulator is put on. The design change helps to make sure the crew oxygen mask/regulator
can be reliably deployed in an emergency.
This service bulletin gives instructions to replace each crew oxygen mask/regulator and stowage box in the flight
compartment to let the crew oxygen mask/regulator be put on immediately in an emergency.
Boeing Service Related Problem (SRP) 747-8-SRP-35-0057 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 747 FTD 35-14002 is related to this service bulletin.
Zodiac Aerospace SB MXP-MLD-747-35-01 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
7 of 25

### Page 8

ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., ComplianceYesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedYesAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION (PRR 85901-144S)
Remove the four crew oxygen masks/regulators and stowage boxes. Install four new or changed crew oxygen
masks/regulators and stowage boxes.
EFFECTIVITY
747-8 and 747-8F Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplane(s).
Refer to Paragraph 1.A.2., Spares Affected, for the list of affected components.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the change given in this service bulletin be done within 72 months after the Original
Issue date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
8 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 9 (OCR)

BOEING SERVICE BULLETIN 747-35-2133
Refer to Paragraph 2.A., Material - Price and Availability.
REMOVE THE FOUR CREW OXYGEN
MASKS/REGULATORS AND STOWAGE
BOXES. INSTALL FOUR NEW OR CHANGED
CREW OXYGEN MASKS/REGULATORS
AND STOWAGE BOXES.
FLIGHT COMPARTMENT  2477896
Original Issue: October 13, 2017
Revision 1: November 01, 2017  Export Controlled ECCN: 9E991 - BOEING  747-35-2133
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  9 of 25

### Page 10

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
10 of 25
BOEING SERVICE BULLETIN 747-35-2133
BLANK PAGE

### Page 11

Commercial 
Airplanes
747
Service Bulletin
SPECIAL ATTENTION
Number: 747-35-2133
Original Issue: October 13, 2017
Revision 1: November 01, 2017
ATA System: 3511
SUBJECT: OXYGEN - Crew Oxygen System - Crew Oxygen Mask/Regulator and Stowage Box
Change
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D6-30300 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is applicable to 747-8 and 747-8F Airplanes, line numbers 1420-1540, that
have Avox crew oxygen masks/regulators, in 1 Group. The Variable Numbers and Group Information
for the applicable airplanes is given below. An equivalent change is on subsequent production
airplanes. Refer to PRR 85901-144S for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
747-8 and 747-8F airplanes with Avox MLD20-626-1 crew oxygen
masks/regulators and MXP806-1 stowage boxes installed.
-1
Airplane Models:
747-8, 747-8F
GroupVariable Number
1RC001 - RC009
1RC021 - RC040
1RC051 - RC060
1RC066 - RC072
1RC076 - RC077
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
11 of 25

### Page 12

GroupVariable Number
1RC501 - RC514
1RC521 - RC528
1RC541
1RC546 - RC564
1RC566
1RC571 - RC573
1RC601 - RC606
1RC641 - RC644
1RC651 - RC652
1RC661
1RC671 - RC674
2. Spares Affected
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 3.B., Work Instructions for the recommended action.
Part Number
MLD20-626-1
MXP806-1
B. Concurrent Requirements
None.
C. Reason
Accomplishment of this service bulletin will let crew members remove crew oxygen masks/regulators
from the stowage boxes without the occurrence of a harness caught in the face piece or goggles. If
this service bulletin is not done, a harness could get caught in the face piece or goggles and increase
the time to put on the crew oxygen masks/regulators, which may lead to hypoxia and the loss of useful
consciousness, resulting in a loss of control of the airplane.
During flight tests crew oxygen masks/regulators did not function as designed, as users could not put
the crew oxygen masks/regulators on quickly. The crew oxygen mask/regulator took longer to put on
because the harness tubing became caught in the face piece. This condition causes a delay for the
flight crew to put on the mask(s), which may lead to hypoxia and the loss of useful consciousness,
resulting in a loss of control of the airplane. As a solution to this problem, the manufacturer has changed
the design of the crew oxygen mask/regulator and the stowage box to prevent the occurrence of a
harness that could get caught in the face piece or goggles before the crew oxygen mask/regulator is
put on. The design change helps to make sure the crew oxygen mask/regulator can be reliably deployed
in an emergency.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
12 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 13

This service bulletin gives instructions to replace each crew oxygen mask/regulator and stowage box
in the flight compartment to let the crew oxygen mask/regulator be put on immediately in an emergency.
Boeing Service Related Problem (SRP) 747-8-SRP-35-0057 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 747 FTD 35-14002 is related to this service bulletin.
Zodiac Aerospace SB MXP-MLD-747-35-01 is related to this service bulletin.
D. Description
Remove the four crew oxygen masks/regulators and stowage boxes. Install four new or changed crew
oxygen masks/regulators and stowage boxes.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
221, 222747-8, 747-8F
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the change given in this service bulletin be done within 72 months after the
Original Issue date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
13 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 14

• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251Open Access
2.002.001FIGURE 1
2.002.001FIGURE 2
1.001.001Test
0.250.251Close Access
5.505.50TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+46.2+0.3747-8
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 85901-144S
b. Boeing Service Related Problem (SRP) 747-8-SRP-35-0057
c. Service Bulletin Index D6-30300
d. 747 Fleet Team Digest (FTD) 35-14002
e. 747-8 Aircraft Maintenance Manual (AMM) 20-41-01, 35-00-00, 35-11-18
f. Zodiac Aerospace Service Bulletin MXP-MLD-747-35-01
NOTE: The supplier was told to send copies of the service bulletin to each operator.
2. Data Supplied with this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
14 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 15

3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
OXYGEN MASK INSTL - CREW OXYGEN WITH SFE FULL FACE
MASKS
232U8000
EQUIPMENT INSTALLATION - CREW OXYGEN232U8002
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
35-11747-8 Aircraft Maintenance Manual - Prac-
tices and Procedures
35-11747-8 Fault Isolation Manual
35-11747-8 Illustrated Parts Catalog
1.30747-8 Flight Crew Operations Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary for Each Airplane, for interchangeability and intermixability
information.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
15 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 16

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
16 of 25
BOEING SERVICE BULLETIN 747-35-2133
BLANK PAGE

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. Use Zodiac Aerospace SB MXP-MLD-747-35-01 to change crew oxygen mask/regulator part
number MLD20-626-1 and change stowage box part number MXP806-1, or procure a new crew oxygen
mask/regulator and stowage box.
B. Industry Support Information
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
NotesExisting Part NumberNameQTYPart Number /
Specification
(a)(b)MLD20-626-1FULL FACE CREW OXYGEN MASK
WITH REMOVABLE SMOKE GOG-
GLES
4MLD20-726-1
(a)(b)MXP806-1STOWAGE BOX, CREW OXYGEN
MASK
4MXP806-7
(a) You can use a new part, or change the existing part to the new part in accordance with Zodiac Aerospace
SB MXP-MLD-747-35-01.
(b) You cannot use the existing part to replace the new or changed part.
3. Parts Modified and Reidentified
The parts shown below are changed as shown in this service bulletin. The quantity (QTY) is the
number of parts changed on each airplane.
NotesNew Part NumberNameQTYExisting Part
Number
(a)(b)(c)MLD20-726-1FULL FACE CREW
OXYGEN MASK WITH
REMOVABLE SMOKE
GOGGLES
4MLD20-626-1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
17 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 18

NotesNew Part NumberNameQTYExisting Part
Number
(a)(b)(c)MXP806-7STOWAGE BOX,
CREW OXYGEN MASK
4MXP806-1
(a) Make the change in accordance with Zodiac Aerospace SB MXP-MLD-747-35-01. Or, as
an alternative, a new part can be installed. Refer Paragraph 2.C.2., Parts and Materials
Supplied by the Operator.
(b) This is the part number after the change is done in accordance with Zodiac Aerospace SB
MXP-MLD-747-35-01.
(c) You cannot use the existing part to replace the new or changed part.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
Refer to Zodiac Aerospace SB MXP-MLD-747-35-01.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
18 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
USE ONLY OXYGEN-CLEAN COMPONENTS IN THE OXYGEN SYSTEM. IF YOU
DO NOT USE OXYGEN-CLEAN COMPONENTS, A FIRE OR AN EXPLOSION
CAN OCCUR. THIS CAN CAUSE DAMAGE TO EQUIPMENT OR INJURIES TO
PERSONS.
WARNING
KEEP OIL, GREASE, SOLVENTS, AND OTHER FLAMMABLE MATERIALS AWAY
FROM THE COMPONENTS OF THE OXYGEN SYSTEM. THESE MATERIALS
AND OXYGEN CAN CAUSE A FIRE OR AN EXPLOSION.
WARNING
MAKE SURE THAT THE OXYGEN SYSTEM IS DEACTIVATED AND ALL OXYGEN
CYLINDERS ARE FULLY CLOSED. IF THE OXYGEN SYSTEM IS NOT
DEACTIVATED AND ALL THE OXYGEN CYLINDERS ARE NOT FULLY CLOSED,
THE OXYGEN SYSTEM COULD BE PRESSURIZED. IF WORK IS DONE ON A
PRESSURIZED OXYGEN SYSTEM, INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT CAN OCCUR.
WARNING
LOOSEN THE OXYGEN CONNECTIONS CAREFULLY. THE REMAINING OXYGEN
CAN RELEASE WITH A LARGE FORCE AND CAN CAUSE INJURY TO PERSONS
AND DAMAGE TO THE AIRPLANE AND EQUIPMENT.
WARNING
READ AND OBEY THE SAFETY PRECAUTIONARY AND GENERAL
INSTRUCTIONS FOR THE OXYGEN SYSTEM MAINTENANCE PRACTICES IN
747-8 AMM 35-00-00 BEFORE YOU DO THE CHANGE.
CAUTION
FAILURE TO OBSERVE THESE SAFETY PRECAUTIONS AND MAINTENANCE
INSTRUCTIONS COULD RESULT IN A FIRE OR EXPLOSION WHICH CAN
CAUSE SERIOUS INJURY TO PERSONNEL AND SEVERE DAMAGE TO THE
AIRPLANE AND EQUIPMENT.
CAUTION
KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF
METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE
BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES
CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
19 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 20

– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for airframe maintenance tasks are included in Chapter 20 of 747
Aircraft Maintenance Manual (AMM).
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
6. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
7. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
8. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
9. Some steps in the Work Instructions are labeled as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
labeled as RC, including sub-steps under an RC step and any figures identified in
an RC step, must be done to comply with the AD. If a step or sub-step is labeled
"RC Exempt," then the RC requirement is removed from that step or sub-step. An
Alternative Method of Compliance (AMOC) is required for any deviations to RC steps,
including sub-steps and identified figures. Steps not labeled as RC may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC. This is provided that
the RC steps, including sub-steps and identified figures, can still be done as specified,
and the airplane can be put back in an airworthy condition.
B. WORK INSTRUCTIONS
1. Get access to the flight compartment.
2. Make sure that the airplane is electrically grounded. Refer to 747-8 AMM 20-41-01 as an accepted
procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
20 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 21

3. Prepare the airplane for the removal of the crew oxygen masks/regulators and stowage boxes.
Make sure that all pressure is let out of the oxygen lines. Refer to 747-8 AMM 35-11-18 as an
accepted procedure.
DO NOT TIGHTEN THE SHUTOFF VALVE ON EACH OXYGEN CYLINDER MORE
THAN 25 IN-LB (3 NM). TOO MUCH TORQUE CAN CAUSE DAMAGE TO THE
SHUTOFF VALVE.
CAUTION
4. RC: Remove the four crew oxygen masks/regulators and stowage boxes in accordance with
FIGURE 1.
5. RC: Install new or changed crew oxygen masks/regulators and stowage boxes in accordance with
FIGURE 2.
NOTE: Crew oxygen mask/regulator part number MLD20-626-1 and stowage box part number
MXP806-1 can be changed in accordance with Zodiac Aerospace SB
MXP-MLD-747-35-01.
YOU MUST OPEN THE SHUTOFF VALVE SLOWLY, OR HIGH TEMPERATURES
CAN OCCUR. THIS CAN START AN IGNITION WITH THE OXYGEN AND CAN
CAUSE INJURY TO PERSONS AND DAMAGE TO THE EQUIPMENT.
WARNING
6. Do the installation test for the crew oxygen stowage boxes. Refer to 747-8 AMM 35-11-18 as an
accepted procedure. Use the procedure for the 'Airplanes With MLD20-726-1 Oxygen Masks'
configuration of the AMM reference to accomplish this instruction.
a. If the test fails, accomplish corrective actions and repeat the test and applicable corrective
actions until the test is passed.
7. Do the installation test of the crew oxygen masks/regulators. Refer to 747-8 AMM 35-11-18 as an
accepted procedure. Use the procedure for the 'Airplanes With MLD20-726-1 Oxygen Masks'
configuration of the AMM reference to accomplish this instruction.
a. If the test fails, accomplish corrective actions and repeat the test and applicable corrective
actions until the test is passed.
8. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1: November 01, 2017
21 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 22 (OCR)

BOEING SERVICE BULLETIN 747-35-2133
FLIGHT COMPARTMENT
TYPICAL
TYPICAL  2477897
FIGURE 1: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- REMOVAL
(SHEET 1 OF 2)
Original Issue: October 13, 2017
Revision 1 November 01, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-35-2133
Work - See page 1 for details.  22 of 25

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(a)4MXP806-1STOWAGE BOX,
CREW OXYGEN
MASK
Remove1
(a)4MLD20-626-1FULL FACE CREW
OXYGEN MASK WITH
REMOVABLE SMOKE
GOGGLES
Remove
(a) Refer to 747-8 AMM 35-11-18 as an accepted procedure.
FIGURE 1: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- REMOVAL
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1 November 01, 2017
23 of 25
BOEING SERVICE BULLETIN 747-35-2133

### Page 24 (OCR)

BOEING SERVICE BULLETIN 747-35-2133
FLIGHT COMPARTMENT
TYPICAL
TYPICAL  2486974
FIGURE 2: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- INSTALLATION
(SHEET 1 OF 2)
Original Issue: October 13, 2017
Revision 1 November 01, 2017  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  747-35-2133
Work - See page 1 for details.  24 of 25

### Page 25

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
This task is applica-
ble if you changed
the existing part to
the new part in accor-
dance with Zodiac
Aerospace SB MXP-
MLD-747-35-01. (a)
4MLD20-726-1FULL FACE CREW
OXYGEN MASK WITH
REMOVABLE SMOKE
GOGGLES
Install (Changed)1
This task is applica-
ble for a new part.
(a)
4MLD20-726-1FULL FACE CREW
OXYGEN MASK WITH
REMOVABLE SMOKE
GOGGLES
Install (New)
This task is applica-
ble if you changed
the existing part to
the new part in accor-
dance with Zodiac
Aerospace SB MXP-
MLD-747-35-01. (a)
4MXP806-7STOWAGE BOX,
CREW OXYGEN
MASK
Install (Changed)
This task is applica-
ble if you got a new
part. (a)
4MXP806-7STOWAGE BOX,
CREW OXYGEN
MASK
Install (New)
(a) Refer to 747-8 AMM 35-11-18 as an accepted procedure.
FIGURE 2: FLIGHT COMPARTMENT - CREW OXYGEN MASKS/REGULATORS AND STOWAGE BOXES
- INSTALLATION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 13, 2017
747-35-2133Revision 1 November 01, 2017
25 of 25
BOEING SERVICE BULLETIN 747-35-2133

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
