# Boeing Special Attention Service Bulletin 757-24-0105: U.S. DOT/FAA - Service Bulletin (2)

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-1311; AD 2012-02-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-24-0105](https://openairdocs.org/service-documents/boeing/sb-757-24-0105.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin (2)
- Pages: 41
- PDF: https://openairdocs.org/files/sha256/a3/0b/a30b37cd648fab3518f70fae39bb508884a8c4f8a342b3080c076d52d2d7f50f
- Page: https://openairdocs.org/service-documents/boeing/sb-757-24-0105/file/a30b37cd648f

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0105
Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Slat Auxiliary Track.
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2004 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the Boeing livery are all
trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document
unless provided in writing by Boeing.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
1 of 41
5.0

### Page 2

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
2 of 41
BOEING SERVICE BULLETIN 757-24-0105
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 5
D. Description .............................................. 1 7
E. Compliance .............................................. 1 8
F. Approval ............................................... 1 8
G. Manpower .............................................. 1 8
H. Weight and Balance Changes .................................... 1 9
I. Electrical Load Data ......................................... 1 9
J. References .............................................. 1 9
1. Existing Data: ......................................... 1 9
2. Data supplied with this Service Bulletin: ........................... 2 0
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 0
K. Publications Affected ........................................ 2 0
L. Interchangeability and Intermixability of Parts ........................... 2 0
2. MATERIAL INFORMATION ........................................ 2 1
A. Material - Price and Availability ................................... 2 1
B. Industry Support Information .................................... 2 1
C. Parts Necessary For Each Airplane ................................. 2 1
1. Kits/Parts: ........................................... 2 1
2. Parts and Materials Supplied by the Operator: ........................ 2 1
3. Parts Modified and Reidentified: ............................... 2 2
4. Parts Removed and Not Replaced: .............................. 2 2
D. Parts Necessary to Change Spares ................................. 2 2
E. Special Tooling - Price and Availability ............................... 2 2
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 3
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 5
A. GENERAL INFORMATION ..................................... 2 5
B. WORK INSTRUCTIONS ....................................... 2 6
FIGURE 1: GROUP 1, CONFIGURATION 1, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION. .... 3 0
FIGURE 2: GROUP 1, CONFIGURATION 1, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION. .... 3 3
FIGURE 3: GROUP 1, CONFIGURATION 2, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION. .... 3 6
FIGURE 4: GROUP 1, CONFIGURATION 2, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION. .... 3 9
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
3 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 4

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
4 of 41
BOEING SERVICE BULLETIN 757-24-0105
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-24-0105Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Slat Auxiliary Track.
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
More work is necessary on airplanes changed as shown in the original issue or Revisions 1,2,3 or 4 of this
service bulletin. Airplanes moved from Group 2 to Group 1, Configuration 2 should make sure that the clamp is
installed on the lower bracket on the left wing as shown in Figure 3.
REASON FOR REVISION
Revision 5 is sent to change the Group and Configuration data, to add maintenance zones, and to add another
optional fastener to plug the hole in the bracket.
These sections were changed:
1. Summary, Action: Added Configuration 1 and Configuration 2 to Group 1 airplanes.
2. Paragraph 1.A.1. Airplanes: Changed from Group 1 and Group 2 to Group 1, Configuration 1 and Group
1, Configuration 2.
3. Paragraph 1.C., Reason: Added Configuration 1 to airplane Group 1.
4. Paragraph 1.D. Description: Added Configuration 1 and Configuration 2 to Group 1 airplanes.
5. Paragraph 1.D. Description: Added Affected Maintenance Zones.
6. Paragraph 1.F. Approval: Changed paragraph letter for Alternate Method Of Compliance.
7. Paragraph 2.C.2., Parts and Materials Supplied by the Operator: Added optional blind rivet, part number
NAS1398B8AB2. Also corrected the part number of the collar to read BACC30M8U.
8. Figure 1, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
5 of 41

### Page 6

9. Figure 2, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
10. Figure 3, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
11. Figure 4, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
The data given in Information Notice 757-24-0105 IN 02 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
September 30, 2004Original Issue:
June 23, 2005Revision 1:
April 20, 2006Revision 2:
October 03, 2006Revision 3:
January 04, 2008Revision 4:
July 30, 2009Revision 5:
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
6 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-24-0105Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Slat Auxiliary Track.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
The changes in this service bulletin will prevent possible chafe damage between the number 5 and 6 inboard
slat auxiliary slat tracks and the power feeder wire bundles W3312 and W3412. The attach points for the support
clamps for the power feeder wires in each wing are changed to get the necessary clearance for the power feeder
wires.
One operator told Boeing they found that the power feeder wire bundle had chafed against the number 6 auxiliary
slat track at Front Spar Station (FSS) 148.90. On one airplane two of the three phases of the power feeder wire
bundle were worn through to the conductor. The electrical cables had arced against the auxiliary slat track and
caused damage to the auxiliary slat track and power feeder wire. This condition can result in a possible ignition
source for leaked flammable fluids or a generator trip with loss of power from that generator.
The attach bracket for the power feeder wire bundle clamp at FSS 148.90 has two holes where the power feeder
wire bundle can be installed. The support clamp for the damaged power feeder wires was attached to the upper
hole of the attach bracket. It was found that the lower hole of the attach bracket can be used to give sufficient
clearance between the power feeder wire bundle and the auxiliary slat track.
This service bulletin gives instructions to do a general visual inspection of the power feeder wire bundles W3312
and W3412 for chafe damage and to make sure that the support clamps are correctly installed. Support clamps
for the power feeder wire bundles are found in the left and right wings at FSS 148.90 near the number 5 and 6
inboard auxiliary slat tracks. Airplane group 1, line numbers 1 - 88 should use the upper hole of the 271N6178-5
bracket to attach the left power feeder wire bundle. Rivets are installed in the open holes that are not used in
the brackets to prevent use of the holes. If Service Letter 757-SL-24-072 has been done, install rivets in the
open holes that are not used in the attach brackets. A similar change was made on line number 1024 and
subsequent airplanes before they were delivered.
The related 757-300 bulletin is 757-24-0106.
Service Letter 757-SL-24-072 is also related to this service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
7 of 41

### Page 8

Boeing Service Related Problem (SRP) 757-SRP-24-0109 is related to this service bulletin.
ACTION
For Group 1, Configuration 1 airplanes: get access to the support clamps for the power feeder wire bundles
W3312 and W3412 at FSS 148.90 in the left and right wings. Do a general visual inspection of each power
feeder wire bundle. Repair damaged wires as necessary. Make sure that the support clamp on the left wing
power feeder wire bundle (W3312) is installed in the upper hole of the 271N6178-5 bracket. Make sure that the
lobe of the clamp is installed in the up position. Make sure that the cable support on the right wing power feeder
wire bundle (W3412) is installed in the lower hole of the 287N1401-306 support bracket. Rivet plug the holes in
the brackets that are not used to prevent use, this includes airplanes that have done Service Letter 757-SL-24-072.
For Group 1, Configuration 2 airplanes: get access to the support clamps for the power feeder wire bundles
W3312 and W3412 at FSS 148.90 in the left and right wings. Do a general visual inspection of each power
feeder wire bundle. Repair damaged wires as necessary. Make sure that the support clamps for the left and
right power feeder wire bundles are installed in the lower hole of the 287N1401-306 support bracket. Rivet plug
the holes in the brackets that are not used to prevent use, this includes airplanes that have done Service Letter
757-SL-24-072.
EFFECTIVITY
757-200, 757-200CB and 757- 200PF airplanes. Refer to Service Bulletin Paragraph 1.A. 1 for effectivity.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2007-03-01
Boeing recommends that operators do the changes in this service bulletin in 24 months or less from the initial
release date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of September 5, 2003. Please refer to
Paragraph 2.B., Industry Support Information.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
4.758.0Group 1, Config-
uration 1
4.257.5Group 1, Config-
uration 2
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
8 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 9 (OCR)

BOEING SERVICE BULLETIN 757-24-0105
INSPECT THE WIRE BUNDLE AT
THIS LOCATION FOR DAMAGE AND
REPAIR IF NECESSARY. CHANGE
THE POSITION OF THE CLAMP.
ISS
150.74
RIGHT WING SHOWN
(LEFT WING EQUIVALENT)
ISS  423837
119.21
Original Issue: September 30, 2004
Revision 5: July 30, 2009  757-24-0105
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  9 of 41

### Page 10

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
10 of 41
BOEING SERVICE BULLETIN 757-24-0105
BLANK PAGE

### Page 11

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0105
Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Slat Auxiliary Track.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
757-200s from line numbers 0001 through 1016.-1
Airplanes that have two attach brackets on the left wing and one
attach bracket on the right wing.
1
Airplanes that have one attach bracket on the left wing and one attach
bracket of the right wing.
2
Airplane Models:
757-200, 757-200CB, 757-200PF
GroupVariable Number
1NA001 - NA028
1NA191 - NA199
1NA201 - NA239
1NA301 - NA305
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
11 of 41

### Page 12

GroupVariable Number
1NA341 - NA352
1NA391 - NA399
1NA401 - NA408
1NA441 - NA447
1NA501 - NA586
1NB001 - NB004
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
1NB166 - NB168
1NB201 - NB204
1NB221 - NB228
1NB230
1NB236
1NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311 - NB312
1NB321 - NB331
1NB421 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB561
1NB571
1NB581 - NB583
1NC001 - NC033
1NC041 - NC042
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
12 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 13

GroupVariable Number
1NC051 - NC052
1NC056 - NC062
1NC066 - NC084
1NC091 - NC094
1NC151
1NC161
1NC901 - NC951
1NC971 - NC974
1ND001 - ND007
1ND011 - ND059
1ND111 - ND113
1ND161 - ND199
1ND201 - ND203
1ND221 - ND225
1ND241 - ND248
1ND301 - ND322
1ND401
1ND891
1ND895
1NE001 - NE008
1NE011 - NE088
1NE091 - NE094
1NE141 - NE150
1NE161 - NE177
1NE201 - NE204
1NE301 - NE302
1NE311 - NE325
1NN001 - NN002
1NN051 - NN052
1NP901 - NP904
1NS601 - NS616
1NT001 - NT009
1NT201 - NT202
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
13 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 14

GroupVariable Number
1NT231 - NT234
1NT237 - NT240
1NT242
1NT245 - NT248
1NT281 - NT289
1NT341 - NT347
1NT351 - NT360
1NT371 - NT373
1NT375 - NT379
1NT381 - NT386
1NT401 - NT409
1NT411 - NT412
1NT426 - NT427
1NT431 - NT432
1NT436 - NT438
1NT441 - NT442
1NT446
1NT701 - NT769
1NT791 - NT796
1NT861 - NT862
1NT881 - NT885
1NT901 - NT916
1NT971 - NT985
1NU031 - NU038
2. Spares Affected
None.
B. Concurrent Requirements
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
14 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 15

C. Reason
The changes in this service bulletin will prevent possible chafe damage between the number 5 and 6
inboard slat auxiliary slat tracks and the power feeder wire bundles W3312 and W3412. The attach
points for the support clamps for the power feeder wires in each wing are changed to get the necessary
clearance for the power feeder wires.
One operator told Boeing they found that the power feeder wire bundle had chafed against the number
6 auxiliary slat track at Front Spar Station (FSS) 148.90. On one airplane two of the three phases of
the power feeder wire bundle were worn through to the conductor. The electrical cables had arced
against the auxiliary slat track and caused damage to the auxiliary slat track and power feeder wire.
This condition can result in a possible ignition source for leaked flammable fluids or a generator trip
with loss of power from that generator.
The attach bracket for the power feeder wire bundle clamp at FSS 148.90 has two holes where the
power feeder wire bundle can be installed. The support clamp for the damaged power feeder wires
was attached to the upper hole of the attach bracket. It was found that the lower hole of the attach
bracket can be used to give sufficient clearance between the power feeder wire bundle and the auxiliary
slat track.
This service bulletin gives instructions to do a general visual inspection of the power feeder wire bundles
W3312 and W3412 for chafe damage and to make sure that the support clamps are correctly installed.
Support clamps for the power feeder wire bundles are found in the left and right wings at FSS 148.90
near the number 5 and 6 inboard auxiliary slat tracks. Airplane Group 1, Configuration 1 should use
the upper hole of the 271N6178-5 bracket to attach the left power feeder wire bundle. Rivets are installed
in the open holes that are not used in the brackets to prevent use of the holes. If Service Letter
757-SL-24-072 has been done, install rivets in the open holes that are not used in the attach brackets.
A similar change was made on line number 1024 and subsequent airplanes before they were delivered.
The related 757-300 bulletin is 757-24-0106.
Service Letter 757-SL-24-072 is also related to this service bulletin.
Boeing Service Related Problem (SRP) 757-SRP-24-0109 is related to this service bulletin.
Revision 1 is sent to add optional fastener data because after the initial release of this service bulletin
an operator told Boeing that they cannot easily get the BACR15FTADR5C rivets.
Optional fastener part numbers are added to Paragraph 2.C.2., Parts and Materials Supplied by the
Operator, and to Step 4 of Figures 1, 2, 3 and 4.
Revision 2 is sent to add a spacer part number to the Group 1 and Group 2 Tables given in Paragraph
2.C.3., Parts and Materials Supplied by the Operator.
Figures 1 through 4 are changed to add the spacer data to the applicable steps.
Revision 3 is sent to correct the compliance recommendation, a note in the Parts and Materials Supplied
by the Operator tables, and to add more part number data applicable to the spacer.
These sections were changed:
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
15 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 16

1. Paragraph 1.E., Compliance; compliance recommendation is changed to add the word "initial" in
the sentence.
2. Paragraph 2.C.2., Parts and Materials Supplied by the Operator; Note (b) is changed to add the
word "not" and to add more part number data applicable to the spacer.
3. Figures 1 through 4, Step 5, the spacer data is changed to give the complete part number and to
give an optional spacer part number.
4. Figure 1, the illustration is changed to show the correct location of the 271N6178-5 bracket.
Revision 4 is sent to correct a part number and to add AD data.
These sections were changed:
1. Summary and Paragraph 1.E., Compliance, and Paragraph 1.F., Approval; added AD data.
2. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added more optional fastener
part number.
3. Paragraph 3.B., Work Instructions, Step 7 and Step 8; added the inspection location.
4. Paragraph 3.B., Work Instructions; added Step 13.
5. Figures 1, 2, 3, and 4; corrected spacer part number, added more clamp data, and added more
optional fastener part number.
The data given in Information Notice 757-24-0105 IN 01 is not included in this revision because the
data contained in 757-24-0105 IN 01 was incorrect.
Revision 5 is sent to change the Group and Configuration data, to add maintenance zones, and to add
another optional fastener to plug the hole in the bracket.
These sections were changed:
1. Summary, Action: Added Configuration 1 and Configuration 2 to Group 1 airplanes.
2. Paragraph 1.A.1. Airplanes: Changed from Group 1 and Group 2 to Group 1, Configuration 1 and
Group 1, Configuration 2.
3. Paragraph 1.C., Reason: Added Configuration 1 to airplane Group 1.
4. Paragraph 1.D. Description: Added Configuration 1 and Configuration 2 to Group 1 airplanes.
5. Paragraph 1.D. Description: Added Affected Maintenance Zones.
6. Paragraph 1.F. Approval: Changed paragraph letter for Alternate Method Of Compliance.
7. Paragraph 2.C.2., Parts and Materials Supplied by the Operator: Added optional blind rivet, part
number NAS1398B8AB2. Also corrected the part number of the collar to read BACC30M8U.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
16 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 17

8. Figure 1, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
9. Figure 2, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
10. Figure 3, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
11. Figure 4, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
The data given in Information Notice 757-24-0105 IN 02 is included in this revision.
D. Description
For Group 1, Configuration 1 airplanes: get access to the support clamps for the power feeder wire
bundles W3312 and W3412 at FSS 148.90 in the left and right wings. Do a general visual inspection
of each power feeder wire bundle. Repair damaged wires as necessary. Make sure that the support
clamp on the left wing power feeder wire bundle (W3312) is installed in the upper hole of the 271N6178-5
bracket. Make sure that the lobe of the clamp is installed in the up position. Make sure that the cable
support on the right wing power feeder wire bundle (W3412) is installed in the lower hole of the
287N1401-306 support bracket. Rivet plug the holes in the brackets that are not used to prevent use,
this includes airplanes that have done the requirements of Service Letter 757-SL-24-072.
For Group 1, Configuration 2 airplanes: get access to the support clamps for the power feeder wire
bundles W3312 and W3412 at FSS 148.90 in the left and right wings. Do a general visual inspection
of each power feeder wire bundle. Repair damaged wires as necessary. Make sure that the support
clamps for the left and right power feeder wire bundles are installed in the lower hole of the
287N1401-306 support bracket. Rivet plug the holes in the brackets that are not used to prevent use,
this includes airplanes that have done the requirements of Service Letter 757-SL-24-072.
The changes in this service bulletin will not change the Engine Indication and Crew Alerting System
(EICAS).
Revision 1 - No more work is necessary on airplanes changed as shown in the initial release of this
service bulletin.
Revision 2 - No more work is necessary on airplanes changed as shown in the initial release or Revision
1 of this service bulletin.
Revision 3 - No more work is necessary on airplanes changed as shown in the Revision 2 of this service
bulletin.
Revision 4 - No more work is necessary on airplanes changed as shown in the Revision 3 of this service
bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
17 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 18

Revision 5 - More work is necessary on airplanes changed as shown in the original issue or Revisions
1,2,3 or 4 of this service bulletin. Airplanes moved from Group 2 to Group 1, Configuration 2 should
make sure that the clamp is installed on the lower bracket on the left wing as shown in Figure 3.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
512, 612757-200, 757-200CB, 757-
200PF
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2007-03-01 is related to this
service bulletin.
Boeing recommends that operators do the changes in this service bulletin in 24 months or less from
the initial release date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
This service bulletin has been approved by the FAA. In addition, the Manager of the FAA Seattle Aircraft
Certification Office approves the action (i.e. inspection or modification) defined in this service bulletin
as an alternative method of compliance to the requirements of paragraph (g) of FAA AD 2007-03-01.
All provisions of FAA AD 2007-03-01 that are not specifically referenced in the above statement remain
fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task-hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task-hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to find the tools.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
18 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 19

Group 1, Configuration 1:
Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.53.02Open Access
0.250.502Inspect
0.750.751Figure 1
0.750.751Figure 2
1.53.02Close Access
4.758.0TOTAL FOR EACH AIRPLANE
Group 1, Configuration 2:
Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.53.02Open Access
0.250.502Inspect
0.500.501Figure 3
0.500.501Figure 4
1.53.02Close Access
4.257.5TOTAL FOR EACH AIRPLANE
NOTE: These manpower estimates do not include time to repair any damaged Power Feeder Wires.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Service Related Problem (SRP) 757-SRP-24-0109.
b. 757 Aircraft Maintenance Manual (AMM) Subject06-44-00, 24-22-00,27-81-00, 32-00-15,
32-00-20, 78-31-00.
c. 757 Structural Repair Manual (SRM) Subject 51-40-02.
d. Boeing Standard Wiring Practices Manual (SWPM)20-10-13.
e. Boeing Service Letter 757-SL-24-072.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
19 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 20

f. Boeing Parts Standards Document D-590.
g. Boeing Drawing 65-88770.
h. Boeing Document D624N001, Service Bulletin Index.
2. Data supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Wire Bundle Instl - L Leading Edge and Front Spar.288N1401
Wire Bundle Instl - R Leading Edge and Front Spar.288N1402
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
None.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
20 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 21

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are available for 757 airplanes in warranty as of September 5, 2003. For
inspection man-hour reimbursement for airplanes in warranty as of that date, send a warranty claim to
Boeing Commercial Airplanes Group - Warranties. If the condition described in this service bulletin is
found during the inspection for airplanes in warranty as of that date and additional man-hours are
required, send a warranty claim to Boeing Commercial Airplanes Group - Warranties. Please refer to
this service bulletin number and reference the airplane variable numbers in your purchase order.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
Group 1, Configuration 1:
NotesNameQTYPart Number / Specifica-
tion
(a)Rivet4BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470
(b)Spacer2BACS18AF4 (Optional:
BACS18AF3)
(a) (c)Fastener4NAS1398B4AB2 or
NAS1398B8AB2
(a) (d)Bolt4BACB30FM8A2
(e)Collar4BACC30M8U
(e)Pressure and Environmental
Sealant
2 ozBMS5-95
(a) Refer to 757 Structural Repair Manual Chapter 51 for alternative fasteners.
(b) The spacer is necessary only if it is not installed under the clamp.
(c) Optional to BACR15( ) or NASM20470 Rivets or BACB30FM8A2 Bolt.
(d) Optional to BACR15( ) or NASM20470 Rivets or NAS1398B4AB2 or NAS1398B8AB2
Fasteners.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
21 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 22

Group 1, Configuration 1:
NotesNameQTYPart Number / Specifica-
tion
(e) Necessary only if BACB30FM8A2 bolt is used.
Group 1, Configuration 2:
NotesNameQTYPart Number / Specifica-
tion
(a) (c)Rivet2BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470
(b)Spacer2BACS18AF4 (Optional:
BACS18AF3)
(a) (c)Fastener2NAS1398B4AB2 or
NAS1398B8AB2
(a) (d)Bolt2BACB30FM8A2
(e)Collar2BACC30M8U
(e)Pressure and Environmental
Sealant
2 ozBMS5-95
(a) Refer to 757 Structural Repair Manual Chapter 51 for alternative fasteners.
(b) The spacer is necessary only if it is not installed under the clamp.
(c) Optional to BACR15( ) or NASM20470 Rivets or BACB30FM8A2 Bolt.
(d) Optional to BACR15( ) or NASM20470 Rivets or NAS1398B4AB2 or NAS1398B8AB2
Fasteners.
(e) Necessary only if BACB30FM8A2 bolt is used.
3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
22 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 23

F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
23 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 24

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
24 of 41
BOEING SERVICE BULLETIN 757-24-0105
BLANK PAGE

### Page 25

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
— Linear dimensions are in inches
— Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch.
— Hole dimensions for standard solid rivets are given in 757 Structural Repair
Manual, Chapter 51
— Torque limits to tighten nuts and bolts are given in 757 Structural Repair Manual,
Chapter 51.
4. For approved fastener and process material substitutions, refer to 757 Structural
Repair Manual, Chapter 51. Alternate fasteners are given in 757 Structural Repair
Manual Chapter 51 and Boeing Drawing 65-88700.
5. If the length of fasteners specified in this service bulletin do not meet the installation
standards, fasteners of the same specification, or an approved substitute, one grip
length longer or shorter may be used.
6. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to ensure visual access to all surfaces in the
inspection area. This level of inspection is made under normal available lighting
conditions such as daylight, hangar lighting, flashlight or drop-light and may require
removal or opening of access panels or doors. Stands, ladders or platforms may be
required to gain proximity to the area being checked.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
25 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 26

B. WORK INSTRUCTIONS
Group 1, Configuration 1:
Airplanes
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEARS.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR COULD RETRACT AND
CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
1. Install the ground lock pins on the nose and main landing gears. Refer to 757 AMM 32-00-20, or
approved equivalent procedure.
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
OPERATION OF THE THRUST REVERSER. ACCIDENTAL OPERATION OF THE
THRUST REVERSER CAN CAUSE INJURY TO PERSONS OR DAMAGE TO
EQUIPMENT.
2. Deactivate the thrust reversers for ground maintenance. Refer to757 AMM 78-31-00, or approved
equivalent procedure.
WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES WHEN
HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS,
SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED SURFACES. INJURY
TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC
POWER IS SUPPLIED.
CAUTION: MAKE SURE THE ACCESS DOOR FOR THE ENGINE STRUT, THE INBOARD FAN
COWLING, AND THE THRUST REVERSER COWLING ARE CLEAR FROM MOVEMENT
OF THE SLATS. IF THE MOVEMENT OF THE SLATS IS BLOCKED, IT CAN CAUSE
DAMAGE TO THE AIRPLANE.
3. Extend the leading edge slats. Refer to 757 AMM 27-81-00, or approved equivalent procedure.
4. Install a DO NOT OPERATE tag on the flap control lever.
5. Remove electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
6. Remove and keep the lower leading edge access panels shown in the table below. Refer to 757
AMM 06-44-00, or approved equivalent procedure.
LocationPanel Number
Left wing511DB
Left wing511EB
Right wing611DB
Right wing611EB
7. Do a general visual inspection of the power feeder wire bundle W3312 in the area of the slat
inboard auxiliary track on the left wing. Install the support clamp and plug the hole in the bracket
that is not used as given in Figure 1.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
26 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 27

8. Do a general visual inspection of the power feeder wire bundle W3412 in the area of the slat
inboard auxiliary track on the right wing. Install the support clamp and plug the hole in the bracket
that is not used as given in Figure 2.
9. Install the lower leading edge access panels shown in the table below. Refer to 757 AMM 06-44-00,
or approved equivalent procedure.
LocationPanel Number
Left wing511DB
Left wing511EB
Right wing611DB
Right wing611EB
10. Apply electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
11. Remove the DO NOT OPERATE tag from the flap control lever.
12. Retract the leading edge slats. Refer to 757 AMM 27-81-00, or approved equivalent procedure.
13. Reactivate the thrust reversers. Refer to 757 AMM 78-31-00, or approved equivalent procedure.
14. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
27 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 28

Group 1, Configuration 2:
Airplanes
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEARS.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEAR COULD RETRACT AND
CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
1. Install the ground lock pins on the nose and main landing gears. Refer to 757 AMM 32-00-20, or
approved equivalent procedure.
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
OPERATION OF THE THRUST REVERSER. ACCIDENTAL OPERATION OF THE
THRUST REVERSER CAN CAUSE INJURY TO PERSONS OR DAMAGE TO
EQUIPMENT.
2. Deactivate the thrust reversers for ground maintenance. Refer to757 AMM 78-31-00, or approved
equivalent procedure.
WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES WHEN
HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS,
SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED SURFACES. INJURY
TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC
POWER IS SUPPLIED.
CAUTION: MAKE SURE THE ACCESS DOOR FOR THE ENGINE STRUT, THE INBOARD FAN
COWLING, AND THE THRUST REVERSER COWLING ARE CLEAR FROM MOVEMENT
OF THE SLATS. IF THE MOVEMENT OF THE SLATS IS BLOCKED, IT CAN CAUSE
DAMAGE TO THE AIRPLANE.
3. Extend the leading edge slats. Refer to 757 AMM 27-81-00, or approved equivalent procedure.
4. Install a DO NOT OPERATE tag on the flap control lever.
5. Remove electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
6. Remove the lower leading edge access panels shown in the table below. Refer to 757 AMM
06-44-00, or approved equivalent procedure.
LocationPanel Number
Left wing511DB
Left wing511EB
Right wing611DB
Right wing611EB
7. Do a general visual inspection of the power feeder wire bundle W3312 in the area of the slat
inboard auxiliary track on the left wing. Install the support clamp and plug the hole in the bracket
that is not used as given in Figure 3.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
28 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 29

8. Do a general visual inspection of the power feeder wire bundle W3412 in the area of the slat
inboard auxiliary track on the right wing. Install the support clamp and plug the hole in the bracket
that is not used as given in Figure 4.
9. Install the lower leading edge access panels shown in the table below. Refer to 757 AMM 06-44-00,
or approved equivalent procedure.
LocationPanel Number
Left wing511DB
Left wing511EB
Right wing611DB
Right wing611EB
10. Apply electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
11. Remove the DO NOT OPERATE tag from the flap control lever.
12. Retract the leading edge slats. Refer to 757 AMM 27-81-00, or approved equivalent procedure.
13. Reactivate the thrust reversers. Refer to757 AMM 78-31-00, or approved equivalent procedure.
14. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5: July 30, 2009
29 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 30 (OCR)

BOEING SERVICE BULLETIN 757-24-0105
SEE A
ISS
169.23
FWD .
ISS
150.74
BEFORE CHANGE  AFTER CHANGE  423833
A
FIGURE 1: GROUP 1, CONFIGURATION 1, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0105
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  30 of 41

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer
to SWPM 20-10-13 for repair.
-W3312Power Feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the upper hole of
the lower bracket. (a) (b)
1BACC10JU() or BACC10GU()
or BACC10GE()
ClampInspect2
1BACN11AG3 or BACN10FX-()
or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
(b)1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open holes in the
287N1401-306 and the
271N6178-5 brackets. 757
SRM 51-40-02. (f)
3BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetsInstall
(New)
4
(e) (f)3NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
3BACB30FM8A2Bolt
(d)3BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
Make sure the clamp is in-
stalled in the upper hole of
the lower bracket. If there is
no spacer, add one. (b)
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-()
or MS21042L3
Nut
FIGURE 1: GROUP 1, CONFIGURATION 1, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
31 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 32

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) If the clamp is in the correct place, install rivets, fasteners, or bolts as given in Step 4.
(b) If BACC10GE() clamp is installed, make sure that the clamp is not aluminum. If aluminum clamp is installed,
discard and replace with new BACC10JU() clamp, or optional BACC10GU() clamp.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolts are used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is to be installed, refer to SRM 51-
20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 1: GROUP 1, CONFIGURATION 1, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
32 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 33 (OCR)

BOEING SERVICE BULLETIN 757-24-0105
SEE Q
FWD
ISS
169.23
ISS
150.74
BEFORE CHANGE  AFTER CHANGE  423834
FIGURE 2: GROUP 1, CONFIGURATION 1, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0105
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  33 of 41

### Page 34

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer
to SWPM 20-10-13 for re-
pair.
-W3412Power feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the lower hole of
the attach bracket. (a) (b)
1BACC10JU() or BACC10GU()
or BACC10GE()
ClampInspect2
1BACN11AG3 or BACN10FX-()
or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
(b)1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open hole in the
287N1401-306 bracket. 757
SRM 51-40-02. (f)
1BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetInstall
(New)
4
(e) (f)1NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
1BACB30FM8A2Bolt
(d)1BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
FIGURE 2: GROUP 1, CONFIGURATION 1, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
34 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 35

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Make sure the clamp is in-
stalled in the lower hole of
the attach bracket. If there is
no spacer, add one. (b)
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-()
or MS21042L3
Nut
(a) If the clamp is in the correct place install rivet, fastener, or bolt as given in Step 4.
(b) If BACC10GE() clamp is installed, make sure that the clamp is not aluminum. If aluminum clamp is installed,
discard and replace with new BACC10JU() clamp, or optional BACC10GU() clamp.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolts are used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is to be installed, refer to SRM 51-
20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 2: GROUP 1, CONFIGURATION 1, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
35 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 36 (OCR)

BOEING SERVICE BULLETIN 757-24-0105
SEE C
ISS
169.23
FWD •
ISS
150.74
3(5)
423835
FIGURE 3: GROUP 1, CONFIGURATION 2, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0105
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  36 of 41

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer
to SWPM 20-10-13 for re-
pair.
-W3312Power Feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the lower hole of
the attach bracket. (a) (b)
1BACC10JU() or BACC10GU()
or BACC10GE()
ClampInspect2
1BACN11AG3 or BACN10FX-()
or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
(b)1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open hole in the
287N1401-306 bracket. 757
SRM 51-40-02. (f)
1BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetInstall
(New)
4
(e) (f)1NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
1BACB30FM8A2Bolt
(d)1BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
FIGURE 3: GROUP 1, CONFIGURATION 2, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
37 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 38

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Make sure the clamp is in-
stalled in the lower hole of
the attach bracket. If there is
no spacer, add one. (b)
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-()
or MS21042L3
Nut
(a) If the clamp is in the correct place, install rivet, fastener, or bolt as given in Step 4.
(b) If BACC10GE() clamp is installed, make sure that the clamp is not aluminum. If aluminum clamp is installed,
discard and replace with new BACC10JU() clamp, or optional BACC10GU() clamp.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolts are used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is to be installed, refer to SRM 51-
20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 3: GROUP 1, CONFIGURATION 2, AIRPLANES, LEFT WING INBOARD AUXILIARY TRACK POWER
FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
38 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 39 (OCR)

BOEING SERVICE BULLETIN 757-24-0105
SEE A
FWD
ISS
169.23
ISS
150.74
423836
FIGURE 4: GROUP 1, CONFIGURATION 2, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0105
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  39 of 41

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer
to SWPM 20-10-13 for repair.
-W3412Power Feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. (a) (b)
1BACC10JU() or BACC10GU()
or BACC10GE()
ClampInspect2
1BACN11AG3 or BACN10FX-()
or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
(b)1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open hole in the
287N1401-306 bracket. 757
SRM 51-40-02. (f)
1BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetInstall
(New)
4
(e) (f)1NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
1BACB30FM8A2Bolt
(d)1BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. If there is no
spacer, add one. (b)
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()
or BACC10GE()
Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-()
or MS2104213
Nut
FIGURE 4: GROUP 1, CONFIGURATION 2, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
40 of 41
BOEING SERVICE BULLETIN 757-24-0105

### Page 41

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) If the clamp is in the correct place, install rivet, fastener, or bolt as given in Step 4.
(b) If BACC10GE() clamp is installed, make sure that the clamp is not aluminum. If aluminum clamp is installed,
discard and replace with new BACC10JU() clamp, or optional BACC10GU() clamp.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolts are used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is to be installed, refer to SRM 51-
20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 4: GROUP 1, CONFIGURATION 2, AIRPLANES, RIGHT WING INBOARD AUXILIARY TRACK
POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0105Revision 5 July 30, 2009
41 of 41
BOEING SERVICE BULLETIN 757-24-0105

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
