# Boeing Special Attention Service Bulletin 757-24-0106: U.S. DOT/FAA - Service Bulletin

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-1311; AD 2012-02-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-24-0106](https://openairdocs.org/service-documents/boeing/sb-757-24-0106.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 27
- PDF: https://openairdocs.org/files/sha256/3b/3a/3b3a3ffb8eaf9d5ac8b1d08b8a620b5f6a20878071e6bcd9e273dc08b447dbee
- Page: https://openairdocs.org/service-documents/boeing/sb-757-24-0106/file/3b3a3ffb8eaf

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0106
Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Auxiliary Slat Track.
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2004 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the Boeing livery are all
trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document
unless provided in writing by Boeing.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
1 of 27
5.0

### Page 2

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
2 of 27
BOEING SERVICE BULLETIN 757-24-0106
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 2
B. Concurrent Requirements ...................................... 1 2
C. Reason ................................................ 1 2
D. Description .............................................. 1 4
E. Compliance .............................................. 1 5
F. Approval ............................................... 1 5
G. Manpower .............................................. 1 5
H. Weight and Balance Changes .................................... 1 6
I. Electrical Load Data ......................................... 1 6
J. References .............................................. 1 6
1. Existing Data: ......................................... 1 6
2. Data supplied with this Service Bulletin: ........................... 1 6
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 1 6
K. Publications Affected ........................................ 1 6
L. Interchangeability and Intermixability of Parts ........................... 1 6
2. MATERIAL INFORMATION ........................................ 1 7
A. Material - Price and Availability ................................... 1 7
B. Industry Support Information .................................... 1 7
C. Parts Necessary For Each Airplane ................................. 1 7
1. Kits/Parts: ........................................... 1 7
2. Parts and Materials Supplied by the Operator: ........................ 1 7
3. Parts Modified and Reidentified: ............................... 1 8
4. Parts Removed and Not Replaced: .............................. 1 8
D. Parts Necessary to Change Spares ................................. 1 8
E. Special Tooling - Price and Availability ............................... 1 8
F. Special Tooling Necessary to do this Service Bulletin ....................... 1 8
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 1 9
A. GENERAL INFORMATION ..................................... 1 9
B. WORK INSTRUCTIONS ....................................... 2 0
FIGURE 1: LEFT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
.................................................. 2 2
FIGURE 2: RIGHT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
.................................................. 2 5
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
3 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 4

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
4 of 27
BOEING SERVICE BULLETIN 757-24-0106
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-24-0106Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Auxiliary Slat Track.
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on airplanes changed as shown in the Revision 4 of this service bulletin.
REASON FOR REVISION
Revision 5 is sent to add affected maintenance Zones and add an optional blind rivet NAS1398B8AB2 to plug
the open hole in the bracket.
These sections were changed:
1. Paragraph 1.D., Description: Added Affected Maintenance Zones.
2. Paragraph 1.F., Approval: Changed the paragraph letter for the Alternate Method of Compliance.
3. Paragraph 2.C.2., Parts and Materials Supplied by the Operator: Added optional blind rivet, part number
NAS1398B8AB2. Also corrected the part number of the collar to read BACC30M8U.
4. Paragraph 3.B.7. and 3.B.8., Work Instructions: Added the Inspection Location.
5. Figure 1, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
6. Figure 2, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part numbers,
and corrected the part number of the collar to read BACC30M8U. Added note (f) at the bottom of the step
table.
The data given in Information Notice 757-24-0106 IN 01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
5 of 27

### Page 6

REVISION HISTORY
September 30, 2004Original Issue:
June 23, 2005Revision 1:
April 20, 2006Revision 2:
October 03, 2006Revision 3:
January 04, 2008Revision 4:
July 30, 2009Revision 5:
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
6 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-24-0106Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Auxiliary Slat Track.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
The changes in this service bulletin will prevent possible chafe damage between the number 5 and 6 inboard
slat auxiliary tracks and the power feeder wire bundles W3312 and W3412 or W5784 and W5786. The attach
points for the support clamps for the power feeder wires in each wing are changed to get the necessary clearance
for the power feeder wires.
One operator told Boeing they found that the power feeder wire bundle had chafed against the number 6 slat
auxiliary track at Front Spar Station (FSS) 148.90. On one airplane two of the three phases of the power feeder
wire bundle were worn through to the conductor. The electrical cables had arced against the auxiliary slat track
and caused damage to the auxiliary slat track and power feeder wire. This condition can result in a possible
ignition source for leaked flammable fluids or a generator trip with loss of power from that generator.
The attach bracket for the power feeder wire bundle clamp at FSS 148.90 has two holes where the power feeder
wire bundle can be installed. The support clamp for the damaged power feeder wires was attached to the upper
hole of the attach bracket. It was found that the lower hole of the attach bracket can be used to give sufficient
clearance between the power feeder wire bundle and the auxiliary slat track.
This service bulletin gives instructions to do a general visual inspection of the power feeder wire bundles W3312
and W3412 or W5784 and W5786 for chafe damage and to make sure that the support clamps are correctly
installed. Support clamps for the power feeder wire bundles are found in the left and right wings at FSS 148.90,
near the number 5 and 6 inboard auxiliary slat tracks. Operators should now use the lower hole of the
287N1401-306 bracket to attach the power feeder wire bundle. Rivets are installed in the open holes that are
not used in the brackets to prevent use of the holes. If Service Letter 757-SL-24-072 has been done, install
rivets in the open holes that are not used in the attach brackets. A similar change was made in production on
line number 1024 and subsequent airplanes.
The related 757-200 and 757-200PF bulletin is 757-24-0105.
Service Letter 757-SL-24-072 is also related to this service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
7 of 27

### Page 8

Boeing Service Related Problem (SRP) 757-SRP-24-0109 is related to this service bulletin.
ACTION
Get access to the support clamps for the power feeder wire bundles W3312 and W3412 or W5784 and W5786
at FSS148.90 in the left and right wings. Do a general visual inspection of each power feeder wire bundle. Repair
damaged wires as necessary. Make sure that the support clamps for the left and right power feeder wire bundles
are installed in the lower hole of the 287N1401-306 support brackets. Rivet plug the holes in the bracket that
are not used to prevent use, this includes airplanes that have done Service Letter 757-SL-24-072.
EFFECTIVITY
All 757-300 Airplanes. Refer to Service Bulletin Paragraph 1.A.1 for effectivity.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2007-03-01 is related to this service
bulletin.
Boeing recommends that operators do the changes in this service bulletin in 24 months or less from the initial
release date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of September 5, 2003. Please refer to
Paragraph 2.B., Industry Support Information.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
4.257.5All
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
8 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 9 (OCR)

BOEING SERVICE BULLETIN 757-24-0106
INSPECT THE WIRE BUNDLE AT
THIS LOCATION FOR DAMAGE AND
REPAIR IF NECESSARY. CHANGE
THE POSITION OF THE CLAMP.
ISS
150.74
→ FWD
RIGHT WING SHOWN
(LEFT WING EQUIVALENT)  ISS
119.21
Original Issue: September 30, 2004
Revision 5: July 30, 2009  757-24-0106
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  9 of 27

### Page 10

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
10 of 27
BOEING SERVICE BULLETIN 757-24-0106
BLANK PAGE

### Page 11

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0106
Original Issue: September 30, 2004
Revision 5: July 30, 2009
ATA System: 2420
SUBJECT: ELECTRICAL POWER - AC Generation - Inspection and Clamp Change of Power
Feeder Wire Bundles to Prevent Chafing on the Number 5 and 6 Auxiliary Slat Track.
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
757-300 Airplanes with Wire Bundle W3312 and W3412.-1
757-300 Airplanes with Wire Bundle W5784 and W5786-2
Airplane Models:
757-300
GroupVariable Number
1NL001 - NL002
1NL006 - NL015
2NL101 - NL104
2NL141
2NL601 - NL607
1NU701 - NU705
1NU721 - NU728
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
11 of 27

### Page 12

GroupVariable Number
1NU731 - NU732
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
The changes in this service bulletin will prevent possible chafe damage between the number 5 and 6
inboard slat auxiliary slat tracks and the power feeder wire bundles W3312 and W3412 or W5784 and
W5786. The attach points for the support clamps for the power feeder wires in each wing are changed
to get the necessary clearance for the power feeder wires.
One operator told Boeing they found that the power feeder wire bundle had chafed against the number
6 auxiliary track at Front Spar Station (FSS) 148.90. On one airplane two of the three phases of the
power feeder wire bundle were worn through to the conductor. The electrical cables had arced against
the auxiliary slat track and caused damage to the auxiliary slat track and power feeder wire. This
condition can result in a possible ignition source for leaked flammable fluids or a generator trip with
loss of power from that generator.
The attach bracket for the power feeder wire bundle clamp at FSS 148.90 has two holes where the
power feeder wire bundle can be installed. The support clamp for the damaged power feeder wires
was attached to the upper hole of the attach bracket. It was found that the lower hole of the attach
bracket can be used to give sufficient clearance between the power feeder wire bundle and the auxiliary
slat track.
This service bulletin gives instructions to do a general visual inspection of the power feeder wire bundles
W3312 and W3412 or W5784 and W5786 for chafe damage and to make sure that the support clamps
are correctly installed. Support clamps for the power feeder wire bundles are found in the left and right
wings at FSS 148.90, near the number 5 and 6 inboard auxiliary slat tracks. Operators should now use
the lower hole of the 287N1401-306 bracket to attach the power feeder wire bundle. Rivets are installed
in the open holes that are not used in the brackets to prevent use of the holes. If Service Letter
757-SL-24-072 has been done, install rivets in the open holes that are not used in the attach brackets.
A similar change was made in production on line number 1024 and subsequent airplanes.
Optional fastener part numbers are added to Paragraph 2.C.2., Parts and Materials Supplied by the
Operator, and to Step 4 of Figures 1 and 2.
The related 757-200 and 757-200PF bulletin is 757-24-0105.
Service Letter 757-SL-24-072 is also related to this service bulletin.
Boeing Service Related Problem (SRP) 757-SRP-24-0109 is related to this service bulletin.
Revision 1 is sent to add optional fastener data because after the initial release of this service bulletin
an airline told Boeing that they cannot easily get the BACR15FTADR5C rivets.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
12 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 13

Revision 2 is sent to add a spacer part number to the Group 1 and Group 2 Tables given in Paragraph
2.C.2., Parts and Materials Supplied by the Operator.
Figures 1 through 2 are changed to add the spacer data to the applicable steps.
Revision 3 is sent to correct the compliance recommendation and add more part number data applicable
to the spacer.
These sections were changed:
1. Paragraph 1.E., Compliance; compliance recommendation is changed to add the word "initial" in
the sentence.
2. Paragraph 2.C.2., Parts and Materials Supplied by the Operator; more part number data applicable
to the spacer is added.
3. Figures 1 and 2, Step 5, the spacer data is changed to give the complete part number and to give
an optional spacer part number.
Revision 4 is sent to move airplanes NL101-NL104, NL141, and NL601-NL607 from Group 1 to Group
2.
These sections were changed:
1. Summary, Background; added wire bundle W5784 and W5786 data.
2. Summary, Action; added wire bundle W5784 and W5786 data.
3. Summary and Paragraph 1.E., Compliance, and Paragraph 1.F., Approval; added AD data.
4. Paragraph 1.A.1., Planning Information; added Group 2 airplanes to the Group Configuration Table.
5. Paragraph 1.A.1., Reason; added wire bundle W5784 and W5786 data.
6. Paragraph 1.A.1., Description; added wire bundle W5784 and W5786 data.
7. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added more optional fastener
data.
8. Paragraph 3.B., Work Instructions; added wire bundle W5784 and W5786 data.
9. Figures 1, Step 1, added wire bundle W5784 data and added more optional fastener data.
10. Figures 2, Step 1, added wire bundle W5786 data and added more optional fastener data.
Revision 5 is sent to add affected maintenance zones and add an optional blind rivet NAS1398B8AB2
to plug the open hole in the bracket.
These sections were changed:
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
13 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 14

1. Paragraph 1.D., Description: Added Affected Maintenance Zones.
2. Paragraph 1.F., Approval: Changed the paragraph letter for the Alternate Method of Compliance.
3. Paragraph 2.C.2., Parts and Materials Supplied by the Operator: Added optional blind rivet, part
number NAS1398B8AB2. Also corrected the part number of the collar to read BACC30M8U.
4. Paragraph 3.B.7. and 3.B.8., Work Instructions: Added the Inspection Location.
5. Figure 1, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
6. Figure 2, Step 4: Added blind rivet, part number NAS1398B8AB2, added optional bolt and nut part
numbers, and corrected the part number of the collar to read BACC30M8U. Added note (f) at the
bottom of the step table.
The data given in Information Notice 757-24-0106 IN 01 is included in this revision.
D. Description
Get access to the support clamps for the power feeder wire bundles W3312 and W3412 or W5784 and
W5786 at FSS148.90 in the left and right wings. Do a general visual inspection of each power feeder
wire bundle. Repair damaged wires as necessary. Make sure that the support clamps for the left and
right power feeder wire bundles are installed in the lower hole of the 287N1401-306 support brackets.
Rivet plug the holes in the bracket that are not used to prevent use, this includes airplanes that have
done Service Letter 757-SL-24-072.
The changes in this service bulletin will not change the Engine Indication and Crew Alerting System
(EICAS).
Revision 1 - No more work is necessary on airplanes changed as shown in the initial release of this
service bulletin.
Revision 2 - No more work is necessary on airplanes changed as shown in the initial release or Revision
1 of this service bulletin.
Revision 3 - No more work is necessary on airplanes changed as shown in the Revision 2 of this service
bulletin.
Revision 4 - No more work is necessary on airplanes changed as shown in the Revision 3 of this service
bulletin.
Revision 5 - No more work is necessary on airplanes changed as shown in the Revision 4 of this service
bulletin.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
512, 612757-300
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
14 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 15

E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2007-03-01 is related to this
service bulletin.
Boeing recommends that operators do the changes in this service bulletin in 24 months or less from
the initial release date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
This service bulletin has been approved by the FAA. In addition, the Manager of the FAA Seattle Aircraft
Certification Office approves the action (i.e. inspection or modification) defined in this service bulletin
as an alternative method of compliance to the requirements of paragraph (g) of FAA AD 2007-03-01.
All provisions of FAA AD 2007-03-01 that are not specifically referenced in the above statement remain
fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task-hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task-hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to find the tools.
Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.53.02Open Access
0.250.502Inspect
0.500.501Figure 1
0.500.501Figure 2
1.53.02Close Access
4.257.5TOTAL FOR EACH AIRPLANE
NOTE: This manpower estimate does not include time to repair any damaged Power Feeder Wires.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
15 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 16

H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Service Related Problem (SRP) 757-SRP-24-0109.
b. 757 Aircraft Maintenance Manual (AMM) Subject 06-44-00, 24-22-00, 27-81-00, 32-00-15,
32-00-20, 78-31-00.
c. 757 Structural Repair Manual (SRM) Subject 51-40-02.
d. Boeing Standard Wiring Practices Manual (SWPM) 20-10-13.
e. Boeing Service Letter 757-SL-24-072.
f. Boeing Parts Standards Document D-590.
g. Boeing Drawing 65-88700.
h. Boeing Document D624N001, Service Bulletin Index.
2. Data supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Wire Bundle Instl - L Leading Edge and Front Spar.288N1401
Wire Bundle Instl - R Leading Edge and Front Spar.288N1402
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
None.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
16 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are available for 757 airplanes in warranty as of September 5, 2003. For
inspection man-hour reimbursement for airplanes in warranty as of that date, send a warranty claim to
Boeing Commercial Airplanes Group - Warranties. If the condition described in this service bulletin is
found during the inspection for airplanes in warranty as of that date and additional man-hours are
required, send a warranty claim to Boeing Commercial Airplanes Group - Warranties. Please refer to
this service bulletin number and reference the airplane variable numbers in your purchase order.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
None.
2. Parts and Materials Supplied by the Operator:
NotesNameQTYPart Number / Specifica-
tion
(a)Rivet2BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470
(b)Spacer2BACS18AF4 (Optional:
BACS18AF3)
(a) (c)Fastener2NAS1398B4AB2 or
NAS1398B8AB2
(a) (d)Bolt2BACB30FM8A2
(e)Collar2BACC30M8U
(e)Pressure and Environmental Sealant2 ozBMS5-95
(a) Refer to 757 Structural Repair Manual Chapter 51 for alternative fasteners.
(b) The spacer is necessary only if it is not installed under the clamp.
(c) Optional to BACR15( ) or NASM20470 Rivets or BACB30FM8A2 Bolt.
(d) Optional to BACR15( ) or NASM20470 Rivets or NAS1398B4AB2 or NAS1398B8AB2 Fasten-
ers.
(e) Necessary only if BACB30FM8A2 bolt is used.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
17 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 18

3. Parts Modified and Reidentified:
None.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
18 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
— Linear dimensions are in inches
— Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch.
— Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
— Hole dimensions for standard solid rivets are given in 757 Structural Repair
Manual, Chapter 51
— Torque limits to tighten nuts and bolts are given in 757 Structural Repair Manual,
Chapter 51.
4. For approved fastener and process material substitutions, refer to 757 Structural
Repair Manual, Chapter 51. Alternate fasteners are given in 757 Structural Repair
Manual Chapter 51 and Boeing Drawing 65-88700.
5. If the length of fasteners specified in this service bulletin do not meet the installation
standards, fasteners of the same specification, or an approved substitute, one grip
length longer or shorter may be used.
6. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to ensure visual access to all surfaces in the
inspection area. This level of inspection is made under normal available lighting
conditions such as daylight, hangar lighting, flashlight or drop-light and may require
removal or opening of access panels or doors. Stands, ladders or platforms may be
required to gain proximity to the area being checked.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
19 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 20

B. WORK INSTRUCTIONS
WARNING: MAKE SURE THE GROUND LOCK PINS ARE INSTALLED ON ALL THE LANDING
GEARS. WITHOUT THE GROUND LOCK PINS, THE LANDING GEAR COULD RETRACT
AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
1. Install the ground lock pins on the nose and main landing gears. Refer to 757 AMM 32-00-20
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
OPERATION OF THE THRUST REVERSER. ACCIDENTAL OPERATION OF THE
THRUST REVERSER CAN CAUSE INJURY TO PERSONS OR DAMAGE TO
EQUIPMENT.
2. Deactivate the thrust reversers for ground maintenance. Refer to 757 AMM 78-31-00 or approved
equivalent procedure.
WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES WHEN
HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS,
SLATS, SPOILERS AND STABILIZER ARE FULLY POWERED SURFACES. INJURY
TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC
POWER IS SUPPLIED.
CAUTION: MAKE SURE THE ACCESS DOOR FOR THE ENGINE STRUT, THE INBOARD FAN
COWLING, AND THE THRUST REVERSER COWLING ARE CLEAR FROM MOVEMENT
OF THE SLATS. IF THE MOVEMENT OF THE SLATS IS BLOCKED, IT CAN CAUSE
DAMAGE TO THE AIRPLANE.
3. Extend the leading edge slats. Refer to 757 AMM 27-81-00 or approved equivalent procedure.
4. Install a DO NOT OPERATE tag on the flap control lever.
5. Remove electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
6. Remove and keep the lower leading edge access panels shown in the table below. Refer to 757
AMM 06-44-00 or approved equivalent procedure.
LocationPanel Number
Left Wing511DB
Left Wing511EB
Right Wing611DB
Right Wing611EB
7. Do a general visual inspection of the power feeder wire bundle W3312 or W5784 in the area of
the slat inboard auxiliary track on the left wing. Install the support clamp and plug the hole in the
bracket that is not used as given in Figure 1.
8. Do a general visual inspection of the power feeder wire bundle W3412 or W5786 in the area of
the slat inboard auxiliary track on the right wing. Install the support clamp and plug the hole in the
bracket that is not used as given in Figure 2.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
20 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 21

9. Install the kept lower leading edge access panels shown in the table below. Refer to 757 AMM
06-44-00,or approved equivalent procedure.
LocationPanel Number
Left Wing511DB
Left Wing511EB
Right Wing611DB
Right Wing611EB
10. Restore electrical power. Refer to 757 AMM 24-22-00, or approved equivalent procedure.
11. Remove the DO NOT OPERATE tag from the flap control lever.
12. Retract the leading edge slats. Refer to 757 AMM 27-81-00 or approved equivalent procedure.
13. Reactivate the thrust reversers for ground maintenance. Refer to 757 AMM 78-31-00 or approved
equivalent procedure.
14. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5: July 30, 2009
21 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 22 (OCR)

BOEING SERVICE BULLETIN 757-24-0106
SEE
ISS
169.23
FWD C
ISS
150.74
(5
423840
FIGURE 1: LEFT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0106
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  22 of 27

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer to
SWPM 20-10-13 for repair. (a)
-W3312 or W5784Power feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. (b)
1BACC10JU() or BACC10GU()ClampInspect2
1BACN11AG3 or BACN10FX-
() or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
1BACC10JU() or BACC10GU()Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open hole in the
287N1401-306 bracket. 757
SRM 51-40-02. (f )
1BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetInstall
(New)
4
(e) (f)1NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
1BACB30FM8A2Bolt
(d)1BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. If there is no
spacer, add one.
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-
() or MS21042L3
Nut
(a) W3312 is for Group 1 airplanes and W5784 is for Group 2 airplanes.
FIGURE 1: LEFT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5 July 30, 2009
23 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 24

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(b) If the clamp is in the correct place, install rivet, fastener, or bolt as given in Step 4.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolt is used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is installed, refer to SRM 51-20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 1: LEFT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5 July 30, 2009
24 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 25 (OCR)

BOEING SERVICE BULLETIN 757-24-0106
SEE Q
FWD
ISS
169.23
ISS
150.74
423839
FIGURE 2: RIGHT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION
(SHEET 1 OF 3)
Original Issue: September 30, 2004
Revision 5 July 30, 2009  757-24-0106
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  25 of 27

### Page 26

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
For damage or wear. Refer to
SWPM 20-10-13 for repair. (a)
-W3412 or W5786Power feeder Wire
Bundle
Inspect1
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. (b)
1BACC10JU() or BACC10GU()ClampInspect2
1BACN11AG3 or BACN10FX-()
or MS21042L3
NutRemove
/Keep
3
1BACS18AF()Spacer
1BACC10JU() or BACC10GU()Clamp
-NAS1149D0332JWasher
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
Bolt
To plug open hole in the
287N1401-306 bracket. 757
SRM 51-40-02. (f )
1BACR15FT7AD4R5C or
BACR15BB7AD5C or
BACR15BB7D5C or
BACR15FT7AD5 or
BACR15FT7AD5C or
BACR15FT7D5C or
NASM20470 or
RivetInstall
(New)
4
(e) (f)1NAS1398B4AB2 or
NAS1398B8AB2
Fastener
Wet install with BMS5-95. (c)
(f)
1BACB30FM8A2Bolt
(d)1BACC30M8UCollar
(d)-BMS5-95Pressure and Envi-
ronmental Sealant
Make sure the clamp is in-
stalled in the lower hole of the
attach bracket. If there is no
spacer, add one.
1BACS12GU3K() or NAS1801-
3-() or BACS12HN3()
BoltInstall
(Kept)
5
-NAS1149D0332JWasher
1BACC10JU() or BACC10GU()Clamp
1BACS18AF4 (Optional:
BACS18AF3)
Spacer
1BACN11AG3 or BACN10FX-()
or MS21042L3
Nut
(a) W3412 is for Group 1 airplanes and W5786 is for Group 2 airplanes.
FIGURE 2: RIGHT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 2 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5 July 30, 2009
26 of 27
BOEING SERVICE BULLETIN 757-24-0106

### Page 27

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(b) If the clamp is in the correct place, install rivet, fastener, or bolt as given in Step 4.
(c) Increase hole size to 0.247-0.250 inch.
(d) Necessary only if BACB30FM8A2 bolt is used.
(e) Increase hole size to 0.256-0.261 if rivet part number, NAS1398B8AB2 is installed and refer to SRM 51-
20-01.
(f) Install with head on forward or aft surface of bracket as necessary. Make sure there is no interference with
wires, tubes or components.
FIGURE 2: RIGHT WING POWER FEEDER WIRE INSPECTION AND SUPPORT CLAMP INSTALLATION.
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 30, 2004
757-24-0106Revision 5 July 30, 2009
27 of 27
BOEING SERVICE BULLETIN 757-24-0106

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
