# Boeing Special Attention Service Bulletin 757-24-0132: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-1229; AD 2013-24-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-24-0132](https://openairdocs.org/service-documents/boeing/sb-757-24-0132.md)
- Title as filed: U.S. DOT/FAA - SB-757-24-01-32-01(1)
- Pages: 76
- PDF: https://openairdocs.org/files/sha256/ca/0f/ca0f681a64808b971bfeaf36e5665374442e588781c219aff45e936093cbd0f5
- Page: https://openairdocs.org/service-documents/boeing/sb-757-24-0132/file/ca0f681a6480

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0132
Original Issue: April 14, 2011
Revision 1: June 19, 2012
ATA System: 2431
SUBJECT: ELECTRICAL POWER - Batteries - Change to the Battery Charger System Wiring for
Extended Flight on Limited Standby Power
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2011 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner™,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and Boeing
liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection
with this document unless provided in writing by Boeing. BOEING is a trademark of Boeing Management
Company.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
1 of 76
11.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
2 of 76
BOEING SERVICE BULLETIN 757-24-0132
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 3
A. Effectivity ............................................... 1 3
1. Airplanes ............................................ 1 3
2. Spares Affected ........................................ 1 7
B. Concurrent Requirements ...................................... 1 7
C. Reason ................................................ 1 8
D. Description .............................................. 1 8
E. Compliance .............................................. 1 9
F. Approval ............................................... 1 9
G. Manpower .............................................. 2 0
H. Weight and Balance Changes .................................... 2 3
I. Electrical Load Data ......................................... 2 3
J. References .............................................. 2 3
1. Existing Data: ......................................... 2 3
2. Data Supplied with this Service Bulletin: ........................... 2 3
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 4
K. Publications Affected ........................................ 2 4
L. Interchangeability and Intermixability of Parts ........................... 2 4
M. Software Accomplishment Summary ................................ 2 4
2. MATERIAL INFORMATION ........................................ 2 5
A. Material - Price and Availability ................................... 2 5
B. Industry Support Information .................................... 2 5
C. Parts Necessary for Each Airplane ................................. 2 6
1. Kits/Parts ............................................ 2 6
2. Parts and Materials Supplied by the Operator ........................ 2 9
3. Parts Modified and Reidentified ................................ 2 9
4. Parts Removed and Not Replaced .............................. 2 9
D. Parts Necessary to Change Spares ................................. 2 9
E. Special Tooling - Price and Availability ............................... 2 9
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 9
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 1
A. GENERAL INFORMATION ..................................... 3 1
B. WORK INSTRUCTIONS ....................................... 3 1
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078 ........................ 3 6
FIGURE 2: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 1] ................. 4 2
FIGURE 3: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 2] ................. 4 5
FIGURE 4: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 3] ................. 4 8
FIGURE 5: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 4] ................. 5 1
FIGURE 6: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 6] ................. 5 4
FIGURE 7: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 7] ................. 5 7
FIGURE 8: WIRING CHANGE FOR WIRE BUNDLE W2078 [Group 5, 8] ................ 6 0
FIGURE 9: WIRE ROUTING FOR WIRE BUNDLE W1260 ........................ 6 3
FIGURE 10: WIRING CHANGE FOR WIRE BUNDLE W1260 [Group 1, 8] ................ 6 5
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
3 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 4

FIGURE 11: WIRING CHANGE FOR WIRE BUNDLE W1260 [Group 2, 6] ................ 6 7
FIGURE 12: WIRING CHANGE FOR WIRE BUNDLE W1260 [Group 3] ................. 6 9
FIGURE 13: WIRING CHANGE FOR WIRE BUNDLE W1260 [Group 4, 7] ................ 7 1
FIGURE 14: WIRING CHANGE FOR WIRE BUNDLE W1260 [Group 5] ................. 7 3
FIGURE 15: INSTALLATION OF RELAY ON P36 PANEL ......................... 7 5
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
4 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-24-0132Original Issue: April 14, 2011
Revision 1: June 19, 2012
ATA System: 2431
SUBJECT: ELECTRICAL POWER - Batteries - Change to the Battery Charger System Wiring for
Extended Flight on Limited Standby Power
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on the airplane(s) changed in accordance with the original issue of this service
bulletin.
REASON FOR REVISION
As a part of a service bulletin validation program, this change was completed on airplane ND049 by Service
Bulletin 757-24-0132 Original Issue before the release of Revision 1 of this service bulletin. The changes
completed on airplane ND049 by Service Bulletin 757-24-0132 Original Issue is equivalent to the release of
Revision 1 of this service bulletin. Airplane ND049 has the configuration of a Group 1 airplane.
The original issue of this service bulletin did not provide the split configurations for wires installed in the flight
deck in TB111 terminal track. As a result, airplanes in Group 1, Group 2 and Group 4 were moved into new
Group 8, Group 6 and Group 7 respectively and to provides the new changed instructions for those airplanes.
This revision is sent to change the original issue service bulletin to correct the groupings in the effectivity
applicabilities of section 1.A as follows:
– Airplanes moved from Group 2 to Group 6:
NB561-NB561
– Airplanes moved from Group 4 to Group 7:
NA237-NA239
– Airplanes moved from Group 1 to Group 8:
NA585-NA586, NB148, NB161-NB162, NB168, NB221-NB228, NB230, NB236, NB294-NB299,
NB301-NB302, NB431-NB438, NB446, NB453-NB454, NB511-NB523, NB571, NB581-NB583,
NC058-NC062, NC068-NC084, NC091-NC094, NC151, NC161, NC936-NC950, ND111-ND113,
ND189-ND199, ND224-ND225, ND244-ND248, ND301-ND322, ND401, NE006-NE008, NE091-NE094,
NE301-NE302, NE311-NE325, NL001-NL002, NL006-NL017, NN001-NN002, NN051-NN052, NP901-NP904,
NS601-NS616, NT001-NT009, NT201-NT202, NT231-NT234, NT237-NT240, NT242, NT245-NT248,
NT281-NT289, NT341-NT347, NT351-NT360, NT371-NT373, NT375-NT379, NT381-NT386, NT401-NT409,
NT411-NT412, NT426-NT427, NT431-NT432, NT436-NT438, NT441-NT442, NT446, NT701-NT769,
NT791-NT796, NT861-NT862, NT881-NT885, NT901-NT916, NT971-NT985, NU031-NU038, NU701-NU705,
NU721-NU728, NU731-NU732
These sections were changed:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
5 of 76

### Page 6

1. Summary Background: Clarified to include reference to wire changes.
2. Summary Action: Clarified to include reference to wire changes.
3. Summary Manpower:
– Added new hour table for new Group 6, Group 7 and Group 8.
– Included note regarding optional open/close access hours.
4. Paragraph 1.A. Effectivity: Defined new Group 6, Group 7 and Group 8 airplanes.
5. Paragraph 1.C. Reason: Added information about the changes made as a result of the service bulletin
validation.
6. Paragraph 1.D. Description: Added data for Group 6, Group 7 and Group 8 airplanes.
7. Paragraph 1.G. Manpower: Added note for optional access hours and new tables for Group 6, Group
7 and Group 8 airplanes.
8. Paragraph 1.K. Publications Affected: Added 757 Flight Crew Operations Manual NNC 06.
9. Paragraph 2.A. Material: Changed price and available date(s) of top kits (remove this paragraph if top
kit price does not change).
10. Paragraph 2.C. Parts Necessary for Each Airplane: Replaced existing wire subkit kit 280N3373-101
with new wire subkit 280N3372-104 that contains new parts and wires needed to complete the service
bulletin.
11. Paragraph 3.A. General Information:
– Deleted existing Note 1.
– Renumbered existing Notes 2-5 to Notes 1-4.
– Added new Note 5.
12. Paragraph 3.B. Effectivity:
a. Divided work instructions into four parts:
– Part 1 - Open Access.
– Part 2 - Rework Instructions.
– Part 3 - Close Access.
– Part 4 - Test.
b. Changed functional test steps.
13. Figure 2 - Added new terminal block (if needed), wire, I.D. tape and splice.
14. Figure 3 - Added new terminal block (if needed), wire, I.D. tape and splice.
15. Figure 4 - Added new terminal block (if needed), wire, I.D. tape and splice.
16. Figure 5 - Added new terminal block (if needed), wire, I.D. tape and splice.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
6 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 7

17. Figure 6:
– Moved existing Figure 6 to Figure 9.
– Limited new Figure 6 to Group 6 airplanes.
– Added new terminal block (if needed), wire, I.D. tape and splice.
18. Figure 7:
– Moved existing Figure 7 to Figure 10.
– Limited new Figure 7 to Group 7 airplanes.
– Added new terminal block (if needed), wire, I.D. tape and splice.
19. Figure 8:
– Moved existing Figure 8 to Figure 11.
– Limited new Figure 8 to Group 5 and Group 8 airplanes.
– Added new terminal block (if needed), wire, I.D. tape and splice.
20. Figure 9:
– Moved existing Figure 9 to Figure 12.
– Was old Figure 6.
21. Figure 10:
– Moved existing Figure 10 to Figure 13.
– Was old Figure 7.
– Limited new Figure 10 to Group 1 and Group 8 airplanes.
– Added Flag Note 9.
22. Figure 11:
– Moved existing Figure 11 to Figure 14.
– Was old Figure 8.
– Limited new Figure 11 to Group 2 and Group 6 airplanes.
– Added Flag Note 9.
23. Figure 12:
– Moved existing Figure 12 to Figure 15.
– Was old Figure 9.
– Limited new Figure 12 to Group 3 airplanes.
– Added Flag Note 9.
24. Figure 13:
– Was old Figure 10.
– Limited new Figure 13 to Group 4 and Group 7 airplanes.
– Added Flag Note 9.
25. Figure 14:
– Was old Figure 11.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
7 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 8

– Limited new Figure 14 to Group 5 airplanes.
– Added Flag Note 9.
26. Figure 15: Was old Figure 12.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
April 14, 2011Original Issue:
June 19, 2012Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
8 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 9

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-24-0132Original Issue: April 14, 2011
Revision 1: June 19, 2012
ATA System: 2431
SUBJECT: ELECTRICAL POWER - Batteries - Change to the Battery Charger System Wiring for
Extended Flight on Limited Standby Power
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will let the main battery charger stay powered when the right main AC
bus is powered and when the standby power switch is set to the BAT position during flight. This will prevent
discharge of the main battery. If this service bulletin is not done, the battery will discharge and could cause the
airplane to lose battery power. This would result in the loss of airplane systems connected to the standby buses,
and could affect flight and landing operations.
During the flight of a 757 airplane, the standby power OFF indication came on. The flight crew set the standby
power switch to the BAT position and continued with the flight. The flight continued beyond the battery's capability
to supply power to the standby loads and a number of system annunciations came on. The hot battery bus,
battery bus, DC standby bus and AC standby bus had lost power. The pilots found that the horizontal stabilizer
trim was not available and lateral control was affected. During landing, the inboard tires blew due to lack of
inboard anti-skid. When the airplane stopped, the engines could not be powered off until the standby power
switch was set back to the AUTO position and main generators were switched on to put back power to the
battery charger, battery and the fuel shutoff valves. Some of these conditions would also be found on 767
airplanes.
This service bulletin gives instructions to change wiring and add a new air/ground relay to the battery charger
system. This change will keep the main battery charger powered when right main AC power is available through
the ground service bus and when the standby power switch is in the BAT position during flight. This will prevent
discharge of the main battery.
Boeing Service Related Problem (SRP) 757-SRP-24-0135 is related to this service bulletin.
ACTION (PRR 54530-290RS)
Do the wiring changes between the P5 overhead panel and P36 miscellaneous electronics equipment panel.
Get access to the P36 miscellaneous electronics equipment panel and install a new relay and wires. Do a test
to make sure the change operates correctly.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
9 of 76

### Page 10

EFFECTIVITY
757-200/-200CB/-200PF/-300 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the change given in this service bulletin be done within 60 months after the Revision
1 date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
12.9*22.5*Group 1 Airplanes
12.9*22.5*Group 2 Airplanes
12.9*22.5*Group 3 Airplanes
12.9*22.5*Group 4 Airplanes
12.9*22.5*Group 5 Airplanes
12.9*22.5*Group 6 Airplanes
12.9*22.5*Group 7 Airplanes
12.9*22.5*Group 8 Airplanes
* Hours do not include optional open/close access steps.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
10 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 11

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
11 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 12

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
12 of 76
BOEING SERVICE BULLETIN 757-24-0132
BLANK PAGE

### Page 13

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-24-0132
Original Issue: April 14, 2011
Revision 1: June 19, 2012
ATA System: 2431
SUBJECT: ELECTRICAL POWER - Batteries - Change to the Battery Charger System Wiring for
Extended Flight on Limited Standby Power
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below. Refer to PRR 54530-290RS for data about
this change.
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
Airplanes with different wire configurations.-1
Airplanes with different wire configurations.-2
Airplanes with different wire configurations.-3
Airplanes with different wire configurations.-4
Airplanes with different wire configurations.-5
Airplanes with different wire configurations.-6
Airplanes with different wire configurations.-7
Airplanes with different wire configurations.-8
Airplane Models:
757-200, 757-200CB, 757-200PF, 757-300
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
13 of 76

### Page 14

GroupVariable Number
3NA002 - NA021
2NA022 - NA028
3NA191 - NA192
2NA193 - NA199
4NA201 - NA236
7NA237 - NA239
4NA301 - NA305
4NA341 - NA352
4NA391 - NA399
1NA401 - NA408
1NA441 - NA447
1NA501 - NA584
8NA585 - NA586
1NB001 - NB004
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB147
8NB148
8NB161 - NB162
1NB166 - NB167
8NB168
1NB201 - NB204
8NB221 - NB228
8NB230
8NB236
1NB239
1NB261 - NB267
1NB291 - NB293
8NB294 - NB299
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
14 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 15

GroupVariable Number
8NB301 - NB302
1NB311 - NB312
1NB321 - NB331
1NB421 - NB430
8NB431 - NB438
8NB446
1NB451 - NB452
8NB453 - NB454
1NB501 - NB510
8NB511 - NB523
6NB561
8NB571
8NB581 - NB583
1NC001 - NC033
1NC041 - NC042
1NC051 - NC052
1NC056 - NC057
8NC058 - NC062
1NC066 - NC067
8NC068 - NC084
8NC091 - NC094
8NC151
8NC161
1NC901 - NC935
8NC936 - NC950
1NC951
1NC971 - NC974
1ND001 - ND007
1ND011 - ND059
8ND111 - ND113
1ND161 - ND188
8ND189 - ND199
1ND201 - ND203
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
15 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 16

GroupVariable Number
1ND221 - ND223
8ND224 - ND225
1ND241 - ND243
8ND244 - ND248
8ND301 - ND322
8ND401
1ND891
1ND895
1NE001 - NE005
8NE006 - NE008
1NE011 - NE088
8NE091 - NE094
1NE141 - NE150
1NE161 - NE177
1NE201 - NE204
8NE301 - NE302
8NE311 - NE325
5NJ001 - NJ004
5NJ031 - NJ032
5NJ551 - NJ555
8NL001 - NL002
8NL006 - NL017
5NL101 - NL109
5NL141
5NL601 - NL616
8NN001 - NN002
8NN051 - NN052
8NP901 - NP904
8NS601 - NS616
8NT001 - NT009
8NT201 - NT202
8NT231 - NT234
8NT237 - NT240
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
16 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 17

GroupVariable Number
8NT242
8NT245 - NT248
8NT281 - NT289
8NT341 - NT347
8NT351 - NT360
8NT371 - NT373
8NT375 - NT379
8NT381 - NT386
8NT401 - NT409
8NT411 - NT412
8NT426 - NT427
8NT431 - NT432
8NT436 - NT438
8NT441 - NT442
8NT446
8NT701 - NT769
8NT791 - NT796
8NT861 - NT862
8NT881 - NT885
8NT901 - NT916
8NT971 - NT985
8NU031 - NU038
8NU701 - NU705
8NU721 - NU728
8NU731 - NU732
2. Spares Affected
None.
B. Concurrent Requirements
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
17 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 18

C. Reason
Accomplishment of this service bulletin will let the main battery charger stay powered when the right
main AC bus is powered and when the standby power switch is set to the BAT position during flight.
This will prevent discharge of the main battery. If this service bulletin is not done, the battery will
discharge and could cause the airplane to lose battery power. This would result in the loss of airplane
systems connected to the standby buses and could affect flight and landing operations.
During the flight of a 757 airplane, the standby power OFF indication came on. The flight crew set the
standby power switch to the BAT position and continued with the flight. The flight continued beyond
the battery's capability to supply power to the standby loads and a number of system annunciations
came on. The hot battery bus, battery bus, DC standby bus and AC standby bus had lost power. The
pilots found that the horizontal stabilizer trim was not available and lateral control was affected. During
landing, the inboard tires blew due to lack of inboard anti-skid. When the airplane stopped, the engines
could not be powered off until the standby power switch was set back to the AUTO position and main
generators were switched on to put back power to the battery charger, battery and the fuel shutoff
valves. Some of these conditions would also be found on 767 airplanes.
This service bulletin gives instructions to change wiring and add a new air/ground relay to the battery
charger system. This change will keep the main battery charger powered when right main AC power
is available through the ground service bus and when the standby power switch is in the BAT position
during flight. This will prevent discharge of the main battery.
Boeing Service Related Problem (SRP) 757-SRP-24-0135 is related to this service bulletin.
As a part of a service bulletin validation program, this change was completed on airplane ND049 by
Service Bulletin 757-24-0132 Original Issue before the release of Revision 1 of this service bulletin.
The changes completed on airplane ND049 by Service Bulletin 757-24-0132 Original Issue is equivalent
to the release of Revision 1 of this service bulletin. Airplane ND049 has the configuration of a Group
1 airplane.
Revision 1 is sent to include the changes found during the validation of this service bulletin on Group
1 airplane ND049. The changes include:
– Adding a new burndy block in terminal track TB111 (if necessary).
– Installation of new splice and new wire to increase the length of an existing rerouted wire.
– Made clarifications to the functional test.
– Provide additional open/close access instructions in the flight compartment.
D. Description
Do the wiring changes between the P5 overhead panel and P36 miscellaneous electronics equipment
panel. Get access to the P36 miscellaneous electronics equipment panel and install a new relay and
wires. Do a test to make sure the change operates correctly.
The work in this service bulletin is done in the maintenance zone(s) given below.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
18 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 19

Group 1:
Affected Maintenance Zones
ZoneModel
118, 119, 122757-200, 757-200CB, 757-
200PF
Group 2-4, 6-7:
Affected Maintenance Zones
ZoneModel
118, 119, 122757-200
Group 5:
Affected Maintenance Zones
ZoneModel
118, 119, 122757-200, 757-300
Group 8:
Affected Maintenance Zones
ZoneModel
118, 119, 122757-200, 757-200PF, 757-300
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the change given in this service bulletin be done within 60 months after the
Revision 1 date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
19 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 20

G. Manpower
The table below shows an estimate of the task hours necessary to do this configuration change for
each airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate
with operator task hour data if necessary. The estimate does not include lost time. These are some
examples of lost time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Group 1:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 2
2.44.82FIGURE 9 and FIG-
URE 10
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 2:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 3
2.44.82FIGURE 9 and FIG-
URE 11
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.502Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
20 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 21

Group 3:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 4
2.44.82FIGURE 9 and FIG-
URE 12
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 4:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 5
2.44.82FIGURE 9 and FIG-
URE 13
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 5:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 8
2.44.82FIGURE 9 and FIG-
URE 14
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
21 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 22

Group 5:
Elapsed HoursTask HoursNumber of PersonsTask
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 6:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 6
2.44.82FIGURE 9 and FIG-
URE 11
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 7:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 7
2.44.82FIGURE 9 and FIG-
URE 13
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
Group 8:
Elapsed HoursTask HoursNumber of PersonsTask
1.5*1.5*1Open Access
6.012.02FIGURE 1 and FIG-
URE 8
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
22 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 23

Group 8:
Elapsed HoursTask HoursNumber of PersonsTask
2.44.82FIGURE 9 and FIG-
URE 10
0.250.251FIGURE 15
1.5*1.5*1Close Access
1.252.52Test
12.922.5TOTAL FOR EACH AIRPLANE
* Hours do not include optional open/close access steps.
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+386.0+1.0757-200 Airplanes
+226.0+1.0757-300 Airplanes
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 54530-290RS
b. Boeing Service Related Problem (SRP) 757-SRP-24-0135
c. Standard Overhaul Practices Manual (SOPM) 20-50-05, 20-50-10
d. Standard Wiring Practices Manual (SWPM) 20-10-11, 20-10-12, 20-10-19, 20-30-12, 20-61-11,
20-81-12, 20-81-22, 20-90-11
e. 757 Aircraft Maintenance Manual (AMM) 24-22-00, 24-33-04, 25-25-01, 25-27-01, 25-31-01,
30-31-00, 33-16-00, 52-34-00, 53-01-01
f. 757 Wiring Diagram Manual (WDM) 24-31-11, 32-09-11
g. Service Bulletin Index Document D624N001
2. Data Supplied with this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
23 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 24

3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
SUB KIT - EQUIPMENT / WIRE INSTALLATION. EXTENDED
FLIGHT ON LIMITED STANDBY POWER.
012N0032
WIRE KIT - EXTENDED FLIGHT ON LIMITED STANDBY POWER280N3373
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
NNC 06 (a)757 Flight Crew Operations Manual
24-30757 Aircraft Maintenance Manual
24-31, 32-09, Equipment List757 Wiring Diagram Manual
32-09757 Illustrated Parts Catalog
24-31, 32-09757 System Schematic Manual
(a) FCOM NNC 06 will be removed from the FCOM QRH after each operator has
notified Boeing that they have completed the incorporation of this service
bulletin on their fleet..
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
24 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 25

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane, as shown
below. If there is a limit to the quantity of available kits, a supply sequence is given by Spares. More
kits become available as shown in the Reorder Lead Time (ROLT). ROLT is calculated from the date
Boeing gets the purchase order.
Group 1-4, 6-8:
Unit Price thru
January 13,
2013
ROLT
(Weeks)
QTYDateNameKit Number
$728.00235May 7,
2012
TOP KIT - RETROFIT
KIT FOR EXTENDED
FLIGHT ON LIMITED
STANDBY POWER
012N8929-20
$728.00234May
21,2012
Group 5:
Unit Price thru
January 13,
2013
ROLT
(Weeks)
QTYDateNameKit Number
$733.0023--TOP KIT - RETROFIT
KIT FOR EXTENDED
FLIGHT ON LIMITED
STANDBY POWER
012N8929-25
The kits are subject to the terms and conditions of the Boeing standard purchase order acknowledgment.
After the Unit Price date, new price and ROLT data is applicable. Prices are in United States dollars.
Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Mail to:
Spares Customer Support - MC 36-65
Boeing Spares Department
P.O. Box 3707
Seattle, Washington 98124-2207 USA
B. Industry Support Information
Boeing warranty remedies are not available for the configuration changes given in this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
25 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 26

C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each airplane. The Top Kit is divided into Figure kits for
each installation figure shown in the table below.
Figure Kit
1591Top Kit
111012N8929-20
111012N8929-25
Top Kit
012N8929-25012N8929-20Wire Kit
-1280N3373-
102
11280N3373-
104
1-280N3373-
103
Group 1-4, 6-8:
KIT 012N8929-20
Notes
Existing Part
NumberName
Figure
New Part Number
1591
Qty
BRADY LABEL1..012N0032-2
(a)LACING TAPE -
WHITE
.1.280N3373-2001
(a)LACING TAPE -
BLUE
..1280N3373-2002
RELAY1..BACR13CF2AB
(a) There are more parts than are necessary.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
26 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 27

Group 5:
KIT 012N8929-25
Notes
Existing Part
NumberName
Figure
New Part Number
1591
Qty
BRADY LABEL1..012N0032-2
(a)LACING TAPE -
WHITE
.1.280N3373-2001
(a)LACING TAPE -
BLUE
..1280N3373-2002
RELAY1..BACR13CF2AB
(a) There are more parts than are necessary.
Group 1-4, 6-8:
KIT 280N3373-102
NotesNameQtyNew Part Number
New cut
and cod-
ed wires
for wire
bundle
W1260
WIRE LIST1280N3373-102W
CONNECTOR I.D.
TAPE - D41850J
1280N3373-10201
CONNECTOR I.D.
TAPE - D11738
1280N3373-10202
CONNECTOR I.D.
TAPE - D00596
1280N3373-10203
CONTACT, PIN3BACC47CN1S
CONTACT, SOCK-
ET
5BACC47DJ1
CONTACT, SOCK-
ET
3BACC47DJ2
CONTACT, SOCK-
ET
3BACC47DJ3
RELAY SOCKET1BACS16X1A
(a) There are more parts than are necessary.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
27 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 28

Group 5:
KIT 280N3373-103
NotesNameQtyNew Part Number
New cut
and cod-
ed wires
for wire
bundle
W1260
WIRE LIST1280N3373-103W
CONNECTOR I.D.
TAPE - D41850J
1280N3373-10201
CONNECTOR I.D.
TAPE - D11738
1280N3373-10202
CONNECTOR I.D.
TAPE - D00596
1280N3373-10203
CONTACT, PIN3BACC47CN1S
CONTACT, SOCK-
ET
5BACC47DJ1
CONTACT, SOCK-
ET
3BACC47DJ2
RELAY SOCKET1BACS16X1A
KIT 280N3373-104
NotesNameQtyNew Part Number
New cut
and cod-
ed wires
for wire
bundle
W2078
WIRE LIST1280N3373-104W
CONNECTOR I.D.
TAPE - D03508
1280N3373-10101
CONNECTOR I.D.
TAPE - D41850P
1280N3373-10102
SPLICE I.D.
SLEEVE - SM28
1280N3373-10401
CONTACT, SOCK-
ET
4BACC47CP1S
CLAMP ASSEM-
BLY
2BACC49A2
TERMINAL BLOCK1BACM15C3D
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
28 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 29

KIT 280N3373-104
NotesNameQtyNew Part Number
SPACER2BACS18AR1
SPLICE SEALED
CRIMP
2D-436-36
CONTACT, PIN,
CRIMP REMOV-
ABLE, PER MIL-C-
39029/11
5M39029/11-145
2. Parts and Materials Supplied by the Operator
None.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
29 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 30

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
30 of 76
BOEING SERVICE BULLETIN 757-24-0132
BLANK PAGE

### Page 31

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
B. WORK INSTRUCTIONS
1. Part 1 - Open Access:
a. In the forward cargo compartment, get access to the P36 miscellaneous electronics equipment
panel assembly and wiring by opening the forward cargo compartment door. Refer to 757
AMM 52-34-00 as an accepted procedure.
b. Remove electrical power from the airplane. Refer to 757 AMM 24-22-00 as an accepted
procedure.
c. In the flight compartment:
(1) Open the right forward ceiling lining to get access to the wire bundles.
(2) Open the P11 circuit breaker panel to get access the wire bundles and terminal track
TB111.
(3) On the P5 panel, remove the Standby Power Control Panel M10062 . Refer to 757 AMM
24-33-04 as an accepted procedure.
(4) Remove the P26 Lighting Equipment Panel to access wire bundles outboard of P6 and
P61 panels (if necessary)
d. In the Passenger Cabin:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
31 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 32

(1) If necessary to access wire bundle outboard of the P61 panel and P6 circuit breaker
panel, remove the G1A galley. Refer to 757 AMM 25-31-01 as an accepted procedure.
(2) Between Stations 460-540 right side, remove items below to access wire bundle located
above the E4 equipment rack drip shield:
(a) Remove and keep the passenger seats. Refer to 757 AMM 25-25-01 as an accepted
procedure.
(b) Remove and keep the floor carpets. Refer to 757 AMM 25-27-01 as an accepted
procedure
(c) Remove and keep the outboard floor panel(s). Refer to 757 AMM 53-01-01 as an
accepted procedure.
(d) As an alternative to the items open access steps above, operators can remove and
keep the E4 equipment rack drip shield to access the wire bundle from below the
floor.
e. End Part 1.
2. If necessary, remove electrical power from the airplane. Refer to 757 AMM 24-22-00 as an accepted
procedure.
3. Part 2 - Rework Instructions:
a. Group 1:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 2.
b. Group 2:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 3.
c. Group 3:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 4.
d. Group 4:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 5.
e. Group 5, 8:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 8.
f. Group 6:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 6.
g. Group 7:
From the P5 overhead panel and the P36 disconnect panel, do the wiring change for wire
bundle W2078 in accordance with FIGURE 1 and FIGURE 7.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
32 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 33

h. Group 1, 8:
In the P36 miscellaneous electronics equipment panel, do the wiring change for wire bundle
W1260 in accordance with FIGURE 9 and FIGURE 10.
i. Group 2, 6:
In the P36 miscellaneous electronics equipment panel, do the wiring change for wire bundle
W1260 in accordance with FIGURE 9 and FIGURE 11.
j. Group 3:
In the P36 miscellaneous electronics equipment panel, do the wiring change for wire bundle
W1260 in accordance with FIGURE 9 and FIGURE 12.
k. Group 4, 7:
In the P36 miscellaneous electronics equipment panel, do the wiring change for wire bundle
W1260 in accordance with FIGURE 9 and FIGURE 13.
l. Group 5:
In the P36 miscellaneous electronics equipment panel, do the wiring change for wire bundle
W1260 in accordance with FIGURE 9 and FIGURE 14.
m. On the P36 miscellaneous electronics equipment panel, install a new relay in accordance with
FIGURE 15 .
n. End Part 2.
4. Part 3 - Close Access
a. In the flight compartment:
(1) Install the right forward ceiling lining that were removed to get access to the wire bundles.
(2) Close the P11 circuit breaker panel.
(3) On the P5 panel, install the Standby Power Control Panel M10062 . Refer to 757 AMM
24-33-04 as an accepted procedure.
(4) If removed, install the P26 Lighting Equipment Panel.
b. In the passenger cabin:
(1) If removed, install the G1A galley. Refer to 757 AMM 25-31-01 as an accepted procedure.
(2) In the passenger cabin between Stations 460-540 right side:
(a) If removed, install kept outboard floor panel(s). Refer to 757 AMM 53-01-01 as an
accepted procedure.
(b) If removed, install kept floor carpets. Refer to 757 AMM 25-27-01 as an accepted
procedure.
(c) If removed, install kept passenger seats. Refer to 757 AMM 25-25-01 as an accepted
procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
33 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 34

(d) If removed, install kept drip shield located above the E4 equipment rack.
c. Apply electrical power to the airplane. Refer to 757 AMM 24-22-00 as an accepted procedure.
d. If the P26 Lighting Equipment Panel was removed and installed, perform the Master Dim and
Test - Adjustment Test. Refer to 757 AMM 33-16-00 as an approved procedure.
e. End Part 3.
5. If necessary, apply electrical power to the airplane. Refer to 757 AMM 24-22-00 as an accepted
procedure.
6. Part 4 - Test
a. Do the steps that follow to test the battery charger:
(1) On the P11 overhead circuit breaker panel, make sure the six EICAS circuit breakers are
closed.
DescriptionCircuit BreakerLocation
EICAS CMPTR LC04078P11-3
EICAS UPPER INDC04081P11-3
EICAS CMPTR RC04079P11-4
EICAS LOWER INDC04082P11-4
EICAS DISPLAY SWC04189P11-4
EICAS PILOTS DSPC04094P11-4
(2) On the P61 right side panel, push the ELEC HYD switch on the EICAS MAINT panel.
(3) On the P5 pilots' overhead panel, push the BAT switch to the ON position.
(4) On the P5 pilots' overhead panel, turn the STBY POWER switch to the BAT position.
(5) Make sure the value shown below the STBY/BAT on the bottom of EICAS display for
DC-V is 24 to 32 volts.
(6) Turn the STBY POWER switch to the AUTO position and make sure these values show
below STBY/BAT on the bottom EICAS display.
NOTE: These values will occur quickly. Make sure you monitor the bottom EICAS display
carefully.
(a) DC-A is 33-43 amps.
(b) DC-V increases to 28-36 volts dc then decreases to 24 to 32 volts dc.
(7) Make sure the DC-A value that shows below STBY/BAT on the bottom EICAS display is
positive.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
34 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 35

(8) On the P5 pilots' overhead panel, turn the STBY POWER switch to the BAT position.
(9) Make sure the MAIN BAT DISCH LT (P5) is illuminated.
(10) At the main landing gear, install switch de-actuators on the proximity sensor S10060,
SYS 1 RIGHT MAIN GEAR TRUCK NOT TILT, and S10062, SYS 1 LEFT MAIN GEAR
TRUCK NOT TILT to place the airplane in airmode.
(11) Make sure the MAIN BAT DISCH LT (P5) is not illuminated.
(12) At the main landing gear, remove the switch de-actuators on the proximity sensor S10060,
SYS 1 RIGHT MAIN GEAR TRUCK NOT TILT, and S10062, SYS 1 LEFT MAIN GEAR
TRUCK NOT TILT.
b. Do the Operational Test for the Pitot Probe Anti-Icing System. Refer to 757 AMM 30-31-00
as an accepted procedure.
c. End Part 4.
7. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1: June 19, 2012
35 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 36 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
TB11
D3508  W2078
FWD
1911247
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 1 OF 6)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-24-0132
Work - See page 1 for details.  36 of 76

### Page 37 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
W2078
STA  288  1911293
FLIGHT COMPARTMENT
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 2 OF 6)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
Work - See page 1 for details.  37 of 76

### Page 38 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
STA
263
W2078
STA
365
1911301
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 3 OF 6)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  38 of 76

### Page 39 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
2000
STA
500
W2078
STA
STA  440
365
W2078
1911305
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 4 OF 6)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
Work - See page 1 for details.  39 of 76

### Page 40 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
P36 DISCONNECT
PANEL
• W2078
D41850P
POS 14
1911308
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 5 OF 6)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  40 of 76

### Page 41

The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
Use quantity as necessary when
making changes to wire bundle
W2078. Refer to SWPM 20-10-11
and SWPM 20-10-19 as accepted
procedures.
1280N3373-2002LACING TAPE - BLUE
FIGURE 1: WIRE ROUTING FOR WIRE BUNDLE W2078
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
41 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 42 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 1.
W2078
• 0257-22 1  A022  - 0258-202
B022  - 0259-20 2
D3508  TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
- 0260-22 6  SM28
ЧІН
P5 PILOT OVHD PNL
- W2078-0150-22-
D40296P
P6 MAIN PWR DIST PNL
45
44
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
• ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIGURE 2: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  757-24-0132  42 of 76

### Page 43

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Positions
22 and 23. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 22 and 23 are
not labled, mark "22" and "23" in
12 point character with black
marker on track. Locate positions
22 and 23 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 22 and 23. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 2: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
43 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 44

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11and SW-
PM 20-10-12 as an accepted pro-
cedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 2: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
44 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 45 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 2.
W2078
- 0257-22 1  A022  0258-202
B022  - 0259-20 2
D3508-  TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
0260-22 6  SM28
P5 PILOT OVHD PNL
W2078-0150-22
D40296P
P6 MAIN PWR DIST PNL
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
++ DELETED WIRE OR FORMER ROUTING  ADDED WIRE OR NEW ROUTING
EXISTING WIRE
FIGURE 3: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
Work - See page 1 for details.  45 of 76

### Page 46

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Position
22 and 23. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 22 and 23 are
not labled, mark "22" and "23" in
12 point character with black
marker on track. Locate positions
22 and 23 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 22 and 23. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 3: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
46 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 47

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as an accepted
procedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 3: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
47 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 48 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 3.
W2078
• 0257-22 1  A022  • 0258-20 2
B022  - 0259-20 2
D3508-  TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)  8
- 0260-22 6  SM28
P5 PILOT OVHD PNL
- W2078-0150-22-
D40296P
P6 MAIN PWR DIST PNL
12
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
• ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIGURE 4: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  757-24-0132  48 of 76

### Page 49

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Position
22 and 23. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 22 and 23 are
not labled, mark "22" and "23" in
12 point character with black
marker on track. Locate positions
22 and 23 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 22 and 23. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 4: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
49 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 50

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as an accepted
procedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 4: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
50 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 51 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 4.
W2078
- 0257-22 L  A022  0258-202
B022  - 0259-20 [2
D3508_  TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
0260-22 6  SM28
P5 PILOT OVHD PNL
W2078-0150-22
D40296P
P6 MAIN PWR DIST PNL
45
12
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
+++ DELETED WIRE OR FORMER ROUTING  ADDED WIRE OR NEW ROUTING
EXISTING WIRE
FIGURE 5: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
Work - See page 1 for details.  51 of 76

### Page 52

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Position
22 and 23. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 22 and 23 are
not labled, mark "22" and "23" in
12 point character with black
marker on track. Locate positions
22 and 23 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 22 and 23. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 5: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
52 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 53

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as an accepted
procedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 5: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
53 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 54 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 6.
W2078
• 0257-22 1  A013  • 0258-20 2>
B013  - 0259-20 2
D3508-
TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
-0260-22  SM28
P5 PILOT OVHD PNL
W2078-0150-22
D40296P
P6 MAIN PWR DIST PNL
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
• ADDED WIRE OR NEW ROUTING
/+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIGURE 6: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  757-24-0132  54 of 76

### Page 55

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Position
12 and 13. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 12 and 13 are
not labled, mark "12" and "13" in
12 point character with black
marker on track. Locate positions
12 and 13 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 12 and 13. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 6: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
55 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 56

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as an accepted
procedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 6: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
56 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 57 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 7.
W2078
- 0257-22 L  A013  0258-202
B013  - 0259-20 [2
D3508-  TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
0260-22 6  SM28
P5 PILOT OVHD PNL
W2078-0150-22
D40296P
P6 MAIN PWR DIST PNL
45
12
D41850P
(POS 14)
P36 MISC ELEC EQUIP PNL
ADDED WIRE OR NEW ROUTING
+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIGURE 7: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
PROPRIETARY - Copyright © Unpublished  Work - See page 1 for details.  57 of 76

### Page 58

REFERENCE: 757 WDM 24-31-11
The flag note numbers shown below agree with the numbers shown in the flag symbols in the figure.
More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
1BMS13-48T10C01G022WIRE1
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as accepted pro-
cedures.
2BMS13-48T10C01G020WIRE2
Refer to SWPM 20-61-11 as an
accepted procedure.
3BACC47CP1SCONTACT, SOCKET3
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10101CONNECTOR I.D. TAPE -
D03508
4
If necessary, install burndy block
in terminal track TB111 Position
12 and 13. Refer to SWPM 20-90-
11 as an accepted procedure.
1BACM15C3DTERMINAL BLOCK5
If necessary, install end caps to
secure new burndy block in track.
Refer to SWPM 20-90-11 as an
accepted procedure.
2BACC49A2CLAMP ASSEMBLY
If necessary, install spacers to se-
cure burdy block in track. Refer to
SWPM 20-90-11 as an accepted
procedure.
2BACS18AR1SPACER
If TB111 Positions 12 and 13 are
not labled, mark "12" and "13" in
12 point character with black
marker on track. Locate positions
12 and 13 using existing terminal
track marker as a guide. Refer to
SOPM 20-50-10 as an accepted
procedure to write numbers on
track. As an alternative to writing
on track, operators can install an
equivalent ID label or marker locat-
ing position 12 and 13. Refer to
SOPM 20-50-05 as an accepted
procedure to install marker on
track.
---
FIGURE 7: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
58 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 59

More DataQtyIdentificationName
Flag
Note
Refer to SWPM 20-10-11 and
SWPM 20-10-12 as an accepted
procedures.
1BMS13-48T10C01G022WIRE6
Refer to SWPM 20-90-11 as an
accepted procedure.
4M39029/11-145CONTACT, PIN, CRIMP
REMOVABLE, PER MIL-C-
39029/11
7
Refer to SWPM 20-30-12 as an
accepted procedure. Splice
M81824/1-1 is equivalent part
number to D-436-36.
1D-436-36SPLICE SEALED CRIMP8
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10401SPLICE I.D. SLEEVE -
SM28
Refer to SWPM 20-10-11 as an
accepted procedure.
1280N3373-10102CONNECTOR I.D. TAPE -
D41850P
9
FIGURE 7: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: April 14, 2011
757-24-0132Revision 1 June 19, 2012
59 of 76
BOEING SERVICE BULLETIN 757-24-0132

### Page 60 (OCR)

BOEING SERVICE BULLETIN 757-24-0132
This Figure applies only to: Group 5, 8.
W2078
• 0257-22 1  A013  • 0258-20 2>
B013  - 0259-20 2
D3508-
TB111X
M10062 STBY  (STA 272,
PWR CONT  WL 280,
LBL 16)
- 0260-22  SM28
P5 PILOT OVHD PNL
W2078-0150-22
D40296P
P6 MAIN PWR DIST PNL
45
44
D41850P  9
(POS 14)
P36 MISC ELEC EQUIP PNL
• ADDED WIRE OR NEW ROUTING
/+ DELETED WIRE OR FORMER ROUTING
EXISTING WIRE
FIGURE 8: WIRING CHANGE FOR WIRE BUNDLE W2078
(SHEET 1 OF 3)
Original Issue: April 14, 2011
Revision 1 June 19, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-24-0132
Work - See page 1 for details.  60 of 76

The text continues at https://openairdocs.org/service-documents/boeing/sb-757-24-0132/file/ca0f681a6480.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
