# Boeing Special Attention Service Bulletin 757-25-0309: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2018-0711; AD 2018-26-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-25-0309](https://openairdocs.org/service-documents/boeing/sb-757-25-0309.md)
- Title as filed: SB-757-25-0309-01
- Pages: 22
- PDF: https://openairdocs.org/files/sha256/fc/fb/fcfb382e70f5ed80d8c621f309b8c7774be24accef3093b8eb5fb19b7aa2d965
- Page: https://openairdocs.org/service-documents/boeing/sb-757-25-0309/file/fcfb382e70f5

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-25-0309
Original Issue: June 11, 2014
Revision 1: July 02, 2018
ATA System: 2511
SUBJECT: EQUIPMENT / FURNISHINGS - Flight Compartment Seats - Captain's and First Officer's
Seat Part Number Inspection - Manual Override Adjustment Check
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2014 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
1 of 22
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
2 of 22
BOEING SERVICE BULLETIN 757-25-0309
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 15
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 17
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FIGURE 1: FLIGHT COMPARTMENT SEATS - SEAT PART NUMBER INSPECTION . . . . . . . . . 21
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
3 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
4 of 22
BOEING SERVICE BULLETIN 757-25-0309
BLANK PAGE

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-25-0309Original Issue: June 11, 2014
Revision 1: July 02, 2018
ATA System: 2511
SUBJECT: EQUIPMENT / FURNISHINGS - Flight Compartment Seats - Captain's and First Officer's
Seat Part Number Inspection - Manual Override Adjustment Check
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Effects of this Revision on airplanes on which the Original Issue was previously done:
None.
REASON FOR REVISION
This revision is sent to update the concurrent requirements table to list the current issues of the Ipeco service
bulletins. And, all references to Ipeco service bulletin 098-25-03 were removed, because it does not apply to
the 757 model airplane.
These sections were changed:
1. Summary - Planning Data: Changed "and/or" to "and".
2. Summary - Action: Removed Ipeco service bulletin 098-25-03.
3. Summary - Industrial Support Information: Changed "and/or" to "and".
4. Paragraph 1.B., Concurrent Requirements: Changed the issue number of Ipeco service bulletins.
Removed Ipeco service bulletin 098-25-03.
5. Paragraph 1.D., Description: Added Revision 1 information. Removed Ipeco service bulletin 098-25-03.
6. Paragraph 1.G., Manpower: Removed Ipeco service bulletin 098-25-03.
7. Paragraph 1.J.1., Existing Data: Removed Ipeco service bulletin 098-25-03.
8. Paragraph 1.K., Publications Affected: Changed "and/or" to "and".
9. Paragraph 2.B., Industry Support Information: Changed "and/or" to "and".
10. Paragraph 2.D., Parts Necessary to Change Spares: Removed Ipeco service bulletin 098-25-03.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
5 of 22

### Page 6

11. Paragraph 3.B., Work Instructions: Step 2.b, and 4.b, removed Ipeco service bulletin 098-25-03. Step
4.a, 4.c, changed "and/or" to "and". Added reference to Concurrent Requirement table.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
June 11, 2014Original Issue:
July 02, 2018Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
6 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-25-0309Original Issue: June 11, 2014
Revision 1: July 02, 2018
ATA System: 2511
SUBJECT: EQUIPMENT / FURNISHINGS - Flight Compartment Seats - Captain's and First Officer's
Seat Part Number Inspection - Manual Override Adjustment Check
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
CONCURRENT REQUIREMENTS
Refer to Paragraph 1.B., Concurrent Requirements.
BACKGROUND
Accomplishment of this service bulletin will make sure that captain's and first officer's seats do not have
un-commanded movement due to an improperly adjusted cable for the manual release lever. A manual control
lever cable that is improperly adjusted could result in its clutch mechanism not engaging correctly and cause
an un-commanded seat movement. If this service bulletin is not done, an un-commanded seat movement during
a critical part of a flight, such as take-off or landing may occur, causing a flight control obstruction or unintended
flight control input which could result in the loss of the ability to control the airplane.
A 747 operator reported that during a takeoff, the first officer's seat unlocked from it's seat tracks and moved
aft. The first officer was unable to control the airplane and the captain took over the controls to avoid a rejected
takeoff. The unlocking of the seat from the seat tracks was caused by actuator damage which was a result of
incorrect adjustment of the seats manual release lever cable, allowing the clutch mechanism to only partially
engage. Because 757 airplanes use the same seats in the flight compartment, Boeing has issued this service
bulletin to do a one time adjustment check in accordance with an Ipeco Service Bulletin. Three Ipeco Service
Bulletins have been issued to account for different part number seats installed. Because of in-service seat
interchangeability, operators are told to inspect the part number of the seats installed and use the applicable
Ipeco Service Bulletin.
This service bulletin gives instructions to inspect for the part numbers of the captain's and first officer's seats
and to do a manual override cable adjustment check of the fore/aft manual control cable and the vertical manual
control cable on each seat in accordance with an Ipeco Service Bulletin. The inspection for part number
determination, and if necessary the adjustment of the manual control levers of the captain's and first officer's
seats, will make sure that the seats do not have un-commanded seat movement due to improperly adjusted
fore/aft and vertical manual control levers.
Boeing Service Related Problem (SRP) 757-SRP-25-0320 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 757 FTD 25-13001 is related to this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
7 of 22

### Page 8

This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
NoAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected
(Flight Crew Operations Manual and
FAA Approved Airplane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
NoOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the flight compartment. Inspect for the part number of the captain's and first officer's seat that is
installed on the airplane and compare with part numbers listed on supplier service bulletins Ipeco SB 210-25-04
or Ipeco SB 258-25-08. If the part numbers on the airplane are listed in supplier service bulletins Ipeco SB
210-25-04 or Ipeco SB 258-25-08, do a manual override cable adjustment check of captain's and first officer's
seats in accordance with the applicable Ipeco Service Bulletin.
EFFECTIVITY
757-200 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the inspection/adjustment check given in this service bulletin be done within 72 months
after the original issue date of this service bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and adjustment check given in this service bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
8 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 9 (OCR)

BOEING SERVICE BULLETIN 757-25-0309
MATERIAL INFORMATION
None.
INSPECT FOR THE PART NUMBER OF THE
CAPTAIN'S AND FIRST OFFICER'S SEAT
INSTALLED ON THE AIRPLANE.
DO A MANUAL OVERRIDE
CABLE ADJUSTMENT CHECK
IN ACCORDANCE WITH THE
APPLICABLE IPECO SERVICE
BULLETIN.
VERTICAL
CONTROL  LEVER  FWD
CAPTAIN'S SEAT
FIRST OFFICER'S SEAT OPPOSITE
(TYPICAL)
(LEFT SIDE VÍEW)
FORE/AFT
CONTROL
LEVER
DO A MANUAL OVERRIDE
CABLE ADJUSTMENT CHECK
IN ACCORDANCE WITH THE
APPLICABLE IPECO SERVICE
BULLETIN.
CAPTAIN'S SEAT
FIRST OFFICER'S SEAT OPPOSITE
(TYPICAL)
(RIGHT SIDE VIEW)
Original Issue: June 11, 2014
Revision 1: July 02, 2018  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-25-0309
Work - See page 1 for details.  9 of 22

### Page 10

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
10 of 22
BOEING SERVICE BULLETIN 757-25-0309
BLANK PAGE

### Page 11

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-25-0309
Original Issue: June 11, 2014
Revision 1: July 02, 2018
ATA System: 2511
SUBJECT: EQUIPMENT / FURNISHINGS - Flight Compartment Seats - Captain's and First Officer's
Seat Part Number Inspection - Manual Override Adjustment Check
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D624N001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
757-200 Airplanes line numbers 553 thru 959, delivered with Ipeco
powered captain's and first officer's seats.
-1
Airplane Models:
757-200
GroupVariable Number
1NC151
1NC161
1ND241 - ND248
1NE301 - NE302
1NP901 - NP904
1NT441 - NT442
1NT720 - NT730
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
11 of 22

### Page 12

GroupVariable Number
1NT901 - NT916
2. Spares Affected
Refer to the supplier service bulletins Ipeco SB 210-25-04 or Ipeco SB 258-25-08 for the list of
affected parts that may be in spares and affected.
B. Concurrent Requirements
One of the service bulletins listed below must be done at the same time as this service bulletin:
DescriptionService BulletinCompany
Captain's and first officer's seat manual
override cable adjustment check.
Ipeco SB 210-25-04 Issue 2
(a)(b)
Ipeco
Captain's and first officer's seat manual
override cable adjustment check.
Ipeco SB 258-25-08 Issue 4
(c)(d)
Ipeco
(a) Applicable to airplanes with captain's seat part numbers 3A090-0077-02-1 installed.
(b) Applicable to airplanes with first officer's seat part numbers 3A090-0078-02-1 or 3A090-
0078-03-1 or 3A090-0078-05-1 installed.
(c) Applicable to airplanes with captain's seat part numbers 3A258-0007-01-1 or 3A258-
0041-01-1 installed.
(d) Applicable to airplanes with first officer's seat part numbers 3A258-0008-01-1 or 3A258-
0042-01-1 installed.
C. Reason
Accomplishment of this service bulletin will make sure that captain's and first officer's seats do not have
un-commanded movement due to an improperly adjusted cable for the manual release lever. A manual
control lever cable that is improperly adjusted could result in its clutch mechanism not engaging correctly
and cause an un-commanded seat movement. If this service bulletin is not done, an un-commanded
seat movement during a critical part of a flight, such as take-off or landing may occur, causing a flight
control obstruction or unintended flight control input which could result in the loss of the ability to control
the airplane.
A 747 operator reported that during a takeoff, the first officer's seat unlocked from it's seat tracks and
moved aft. The first officer was unable to control the airplane and the captain took over the controls to
avoid a rejected takeoff. The unlocking of the seat from the seat tracks was caused by actuator damage
which was a result of incorrect adjustment of the seats manual release lever cable, allowing the clutch
mechanism to only partially engage. Because 757 airplanes use the same seats in the flight
compartment, Boeing has issued this service bulletin to do a one time adjustment check in accordance
with an Ipeco Service Bulletin. Three Ipeco Service Bulletins have been issued to account for different
part number seats installed. Because of in-service seat interchangeability, operators are told to inspect
the part number of the seats installed and use the applicable Ipeco Service Bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
12 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 13

This service bulletin gives instructions to inspect for the part numbers of the captain's and first officer's
seats and to do a manual override cable adjustment check of the fore/aft manual control cable and the
vertical manual control cable on each seat in accordance with an Ipeco Service Bulletin. The inspection
for part number determination, and if necessary the adjustment of the manual control levers of the
captain's and first officer's seats, will make sure that the seats do not have un-commanded seat
movement due to improperly adjusted fore/aft and vertical manual control levers.
Boeing Service Related Problem (SRP) 757-SRP-25-0320 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 757 FTD 25-13001 is related to this service bulletin.
Revision 01 is sent to update the concurrent requirements table to list the current issues of the Ipeco
service bulletins.
D. Description
Get access to the flight compartment. Inspect for the part number of the captain's and first officer's seat
that is installed on the airplane and compare with part numbers listed on supplier service bulletins Ipeco
SB 210-25-04 or Ipeco SB 258-25-08. If the part numbers on the airplane are listed in supplier service
bulletins Ipeco SB 210-25-04 or Ipeco SB 258-25-08, do a manual override cable adjustment check of
captain's and first officer's seats in accordance with the applicable Ipeco Service Bulletin.
Effects of this Revision on airplanes on which the Original Issue was previously done:
None.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
211, 212757-200
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the inspection/adjustment check given in this service bulletin be done within
72 months after the original issue date of this service bulletin.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
13 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 14

If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this service bulletin for each
airplane. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with
operator task hour data if necessary. The estimate does not include lost time. These are some examples
of lost time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Elapsed HoursTask HoursNumber of
Persons
Task
0.050.051Open Access
0.200.201FIGURE 1
0.750.751Removal of the Captain's Seat (a)
0.750.751Installation of the Captain's Seat (b)
0.750.751Removal of the First Officer's Seat (a)
0.750.751Installation of the First Officer's Seat (b)
0.250.251Seat Movement Adjustment of the Captain's Seat
(c)
0.250.251Seat Movement Adjustment of the First Officer's
Seat (c)
0.050.051Close Access
0.30 - 3.80 (d)0.30 - 3.80 (d)TOTAL FOR EACH AIRPLANE
(a) Only necessary if it is not possible to adjust the seat with the seat installed.
(b) Only necessary if the seat was removed.
(c) Only necessary if the seat has been adjusted in accordance with the Ipeco Service Bulletin or if a new
seat is installed.
(d) A range of total task hours and elapsed hours is given as the work necessary for each airplane may
vary.
The time to do the adjustment check in accordance with Ipeco SB 210-25-04 and Ipeco SB 258-25-08
is not included.
H. Weight and Balance Changes
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
14 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 15

I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Related Problem (SRP) 757-SRP-25-0320
b. Service Bulletin Index D624N001
c. 757 Aircraft Maintenance Manual (AMM) 25-11-01
d. 757 Fleet Team Digest (FTD) 25-13001
e. Ipeco Service Bulletins 210-25-04, 258-25-08
NOTE: The supplier was advised to send copies of the service bulletins to each operator.
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and changes in this service bulletin for effects on Fatigue Critical
Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
15 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 16

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
16 of 22
BOEING SERVICE BULLETIN 757-25-0309
BLANK PAGE

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and adjustment check given in this service
bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
None.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
Refer to the supplier service bulletins Ipeco SB 210-25-04 or Ipeco SB 258-25-08 for the list of affected
parts that may be in spares and affected.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
17 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 18

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
18 of 22
BOEING SERVICE BULLETIN 757-25-0309
BLANK PAGE

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF
METAL PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED
MATERIAL, METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE
BUNDLES CAN CAUSE DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES
CAN CAUSE SPARKS OR OTHER ELECTRICAL DAMAGE.
CAUTION
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
— Values for airframe maintenance tasks are included in Chapter 20 of 757
Airplane Maintenance Manual (AMM).
— Values for engine maintenance tasks are included in Chapter 70 of 757
Airplane Maintenance Manual (AMM).
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
4. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
5. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
6. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
7. Use of colors in Figures is based on guidance from the ATA e-Business Program
(ATA) iSpec 2200.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
19 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 20

8. Some steps in the Work Instructions are identified as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
identified as RC must be done to comply with the AD. Alternative procedures for
steps not identified with RC can be used if the RC steps can still be done as specified,
and the airplane can be put back in a serviceable condition. An Alternative Method
of Compliance (AMOC) is not necessary for deviations to steps that are not identified
as RC.
B. WORK INSTRUCTIONS
1. Get access to the flight compartment.
2. RC - CAPTAIN'S AND FIRST OFFICER'S SEAT PART NUMBER INSPECTION as follows:
a. Inspect the captain's and first officer's seat to determine the seat part number in accordance
with FIGURE 1. As an alternative, a review of the airplane maintenance records can be used
if the part number of the captain's and first officer's seat that is installed on the airplane can
be conclusively determined.
b. Compare the captain's and first officer's seat part numbers with the part numbers listed in
accordance with the applicable Ipeco service bulletin version listed in Paragraph 1.B.,
Concurrent Requirements.
3. If the seat part number is not specified in any of the Ipeco service bulletins no further action is
necessary.
4. If the seat part number is specified in one of the Ipeco service bulletins and do as follows:
a. Remove and keep the captain's and first officer's seat. Refer to 757 AMM 25-11-01 as an
accepted procedure.
NOTE: Operators can choose not to remove the captain's and first officer's seat if there is
sufficient access to do the manual override cable adjustment check of the seat in
accordance with the applicable Ipeco Service Bulletin with the seat installed.
b. RC - Do a manual override cable adjustment check of the captain's and first officer's seat in
accordance with the applicable Ipeco service bulletin version listed in Paragraph 1.B.,
Concurrent Requirements.
c. If removed, install the kept captain's and first officer's seat that has the seat identification label
marked with the related Ipeco Service Bulletin number. Refer to 757 AMM 25-11-01 as an
accepted procedure.
d. Do the Seat Movement Adjustment. Refer to 757 AMM 25-11-01 as an accepted procedure.
5. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1: July 02, 2018
20 of 22
BOEING SERVICE BULLETIN 757-25-0309

### Page 21 (OCR)

BOEING SERVICE BULLETIN 757-25-0309
CAPTAIN'S SEAT
TYPICAL
LEFT SIDE VIEW
FIRST OFFICER'S SEAT
(TYPICAL)
(LEFT SIDE VIEW)
2311442
FIGURE 1: FLIGHT COMPARTMENT SEATS - SEAT PART NUMBER INSPECTION
(SHEET 1 OF 2)
Original Issue: June 11, 2014
Revision 1 July 02, 2018  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-25-0309
Work - See page 1 for details.  21 of 22

### Page 22

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for this figure.
More DataQtyIdentificationNameTaskStep
(a)1-Captain's SeatInspect1
(a)1-First Officer's SeatInspect2
(a) Inspect the seat to determine the seat part number.
FIGURE 1: FLIGHT COMPARTMENT SEATS - SEAT PART NUMBER INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: June 11, 2014
757-25-0309Revision 1 July 02, 2018
22 of 22
BOEING SERVICE BULLETIN 757-25-0309

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
