# Boeing Special Attention Service Bulletin 757-53-0097: Revision 2

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2016-3697; AD 2017-20-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-53-0097](https://openairdocs.org/service-documents/boeing/sb-757-53-0097.md)
- Title as filed: U.S. DOT/FAA - SB-757-53-0097 Rev2 - 7 28 15
- Pages: 195
- PDF: https://openairdocs.org/files/sha256/8d/29/8d29ec19d662bc656b8d5a5b7ea651c47f910cf0a3a08fd07074048c6e7b3ca3
- Page: https://openairdocs.org/service-documents/boeing/sb-757-53-0097/file/8d29ec19d662

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-53-0097
Original Issue: November 22, 2010
Revision 2: July 28, 2015
ATA System: 5300
SUBJECT: FUSELAGE - Skin - Crown Skin Panel - Station 297 to Station 439, Chem-Milled Steps
Between Stringer 4 Left and Stringer 4 Right Lap Joints - Inspection and Modification
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2010 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
1 of 195
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
2 of 195
BOEING SERVICE BULLETIN 757-53-0097
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1. PLANNING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
A. Effectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
B. Concurrent Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
C. Reason . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D. Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
E. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
F. Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
G. Manpower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
H. Weight and Balance Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
I. Electrical Load Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
J. References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
1. Existing Data: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2. Data Supplied with this Service Bulletin: . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3. Installation Drawings Used in the Preparation of this Service Bulletin: . . . . . . . . . . . 35
K. Publications Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
L. Interchangeability and Intermixability of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
M. Software Accomplishment Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2. MATERIAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
A. Material - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
B. Industry Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
C. Parts Necessary for Each Airplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
1. Kits/Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2. Parts and Materials Supplied by the Operator . . . . . . . . . . . . . . . . . . . . . . . . 38
3. Parts Modified and Reidentified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4. Parts Removed and Not Replaced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
D. Parts Necessary to Change Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
E. Special Tooling - Price and Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
F. Special Tooling Necessary to do this Service Bulletin . . . . . . . . . . . . . . . . . . . . . . . 41
3. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
A. GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
B. WORK INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FIGURE 1: THIS FIGURE WAS DELETED AT REVISION 2 . . . . . . . . . . . . . . . . . . . . . . . 55
FIGURE 2: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
FIGURE 3: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
FIGURE 4: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
FIGURE 5: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
FIGURE 6: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 2 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 1, 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
3 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 4

FIGURE 7: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 2 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
FIGURE 8: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 2 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 1, 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
FIGURE 9: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 2 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
FIGURE 10: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
FIGURE 11: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
FIGURE 12: STA 297 TO STA 418 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SLIDING PROBE EC
INSPECTION [Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
FIGURE 13: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
FIGURE 14: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
FIGURE 15: STA 297 TO STA 418 CROWN SKIN PANEL - ZONE 3 - EXTERNAL SPOT PROBE MFEC
INSPECTION [Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
FIGURE 16: S-4L - STA 297 THRU STA 324 - REMOVAL OF FASTENERS AND OPEN HOLE INSPECTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
FIGURE 17: S-4L - STA 297 THRU STA 324 - MANUFACTURE OF PREVENTIVE MODIFICATION PARTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
FIGURE 18: S-4L - STA 297 THRU STA 324 - INSTALLATION OF PREVENTIVE MODIFICATION . 102
FIGURE 19: S-4L - STA 377.7 THRU STA 439 - REMOVAL OF FASTENERS AND OPEN HOLE INSPECTION
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
FIGURE 20: S-4L - STA 377.7 THRU STA 439 - MANUFACTURE OF PREVENTIVE MODIFICATION PARTS
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
FIGURE 21: S-4L - STA 377.7 THRU STA 439 - INSTALLATION OF PREVENTIVE MODIFICATION [Group
1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
FIGURE 22: S-4R - STA 297 THRU STA 439 - REMOVAL OF FASTENERS AND OPEN HOLE INSPECTION
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
FIGURE 23: S-4R - STA 297 THRU STA 439 - MANUFACTURE OF PREVENTIVE MODIFICATION PARTS
[Group 1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
FIGURE 24: S-4R - STA 297 THRU STA 439 - INSTALLATION OF PREVENTIVE MODIFICATION [Group
1-2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
FIGURE 25: S-4L - STA 377.7 THRU STA 418 - REMOVAL OF FASTENERS AND OPEN HOLE INSPECTION
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
FIGURE 26: S-4L - STA 377.7 THRU STA 418 - MANUFACTURE OF PREVENTIVE MODIFICATION PARTS
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
FIGURE 27: S-4L - STA 377.7 THRU STA 418 - INSTALLATION OF PREVENTIVE MODIFICATION [Group
3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
FIGURE 28: S-4R - STA 297 THRU STA 439 - REMOVAL OF FASTENERS AND OPEN HOLE INSPECTION
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
FIGURE 29: S-4R - STA 297 THRU STA 439 - MANUFACTURE OF PREVENTIVE MODIFICATION PARTS
[Group 3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
FIGURE 30: S-4R - STA 297 THRU STA 439 - INSTALLATION OF PREVENTIVE MODIFICATION [Group
3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
FIGURE 31: POST MODIFICATION INSPECTION REQUIREMENTS [Group 1-2] . . . . . . . . . . . 173
FIGURE 32: POST MODIFICATION INSPECTION REQUIREMENTS  [Group 3] . . . . . . . . . . . . 176
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
4 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 5

APPENDIX A: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE1: STA 297 TO STA 439
CROWN SKIN PANEL – ZONE 1 – INSPECTIONS AND PREVENTIVE MODIFICATION. 181
APPENDIX B: LOGIC DIAGRAM FOR: TABLE 2: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 2 -
INSPECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
APPENDIX C: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 3: STA 297 TO STA 439
CROWN SKIN PANEL – ZONE 3 - INSPECTIONS . . . . . . . . . . . . . . . . . . . . . 189
APPENDIX D: LOGIC DIAGRAM FOR PARAGRAPH 1.E. COMPLIANCE: TABLE 4: STA 297 TO STA 439
CROWN SKIN PANEL – POST PREVENTIVE MODIFICATION SUPPLEMENTAL INSPECTIONS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
APPENDIX E: PART DEMAND INTENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
5 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 6

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
6 of 195
BOEING SERVICE BULLETIN 757-53-0097
BLANK PAGE

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-53-0097Original Issue: November 22, 2010
Revision 2: July 28, 2015
ATA System: 5300
SUBJECT: FUSELAGE - Skin - Crown Skin Panel - Station 297 to Station 439, Chem-Milled Steps
Between Stringer 4 Left and Stringer 4 Right Lap Joints - Inspection and Modification
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2011-01-15 is related to this service bulletin.
The effective date of AD 2011-01-15 is January 25, 2011.
Effects of this Revision on airplanes on which Original Issue or Revision 1 was previously done:
None.
REASON FOR REVISION
This revision is sent to increase compliance times and repeat intervals, to remove the detailed inspection option
and to add a preventive modification. This revision is also sent to add new inspection areas.
These sections were changed:
1. Summary:
a. Background - Revised to include new inspection areas, a preventive modification, new crack
findings and a Summary Evaluation Table is added.
b. Action - Detailed inspection option is removed, new inspection areas and preventive modification
are added.
c. Effectivity - 757-200CB Airplanes removed.
d. Compliance - AD information added.
e. Industry Support Information - Warranty information added.
f. Manpower - Table deleted and 'refer to paragraph 1.G Manpower' added.
g. Summary Illustration revised and new Summery Illustration added.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
7 of 195

### Page 8

2. Paragraph 1.A. Effectivity - 757-200CB removed because manufacture of crown skin panel excludes
it from this service bulletin. Group 2 and Group 3 added to identify 757-200 Airplanes without provision
for an antenna in the crown skin panels, 757-200/300 Airplanes with provision for an antenna in the
crown skin panels and 757-200 Boeing Special Freighter Airplanes.
3. Paragraph 1.C. Reason - Revised to include new inspection areas, a preventive modification, new
crack findings and add why the revision is sent statements.
4. Paragraph 1.D. Description - Detailed inspection option is removed, new inspection areas and preventive
modification are added, and no more work statement is added.
5. Paragraph 1.E. Compliance - Detailed inspection option is removed. Boilerplates for Federal Aviation
Administration (FAA) Airworthiness Directive (AD), paragraph 3, logic diagrams and Options, Conditions,
Actions added. Tables revised for new compliance times and intervals, preventive modification, Parts,
Conditions, Options, and new tables are added.
6. Paragraph 1.F. Approval - FAA alternative method of compliance statement is added.
7. Paragraph 1.G. Manpower - Detailed inspection deleted, tables are reworked and new tables added.
8. Paragraph 1.H. Weight and Balance Changes - New tables are added for each airplane groups.
9. Paragraph 1.J. References - Boeing Service Letter, AD, Aircraft Maintenance Manual (AMM), Standard
Overhaul Practices Manual (SOPM) and Structural Repair Manual (SRM) references are added.
10. Paragraph 2.C.2. Parts and Materials Supplied by the Operator - New tables with new parts are added
for each airplane groups.
11. Paragraph 3.A. General Information - New notes are added.
12. Paragraph 3.B. Work Instructions - Detailed inspection deleted, and work instructions revised into Parts,
Conditions, Options. .
13. Figure 1 has been deleted.
14. Figures 4 thru 32 are added to show new inspections of crown skin, and manufacture,installation and
inspection of preventive modifications.
15. Appendix A, B, C and D Logic Diagrams are added.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity and format changes,
to show the location of all content changes.
Pages with no vertical lines have no changes.
REVISION HISTORY
November 22, 2010Original Issue:
January 06, 2011Revision 1:
July 28, 2015Revision 2:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
8 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 9

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-53-0097Original Issue: November 22, 2010
Revision 2: July 28, 2015
ATA System: 5300
SUBJECT: FUSELAGE - Skin - Crown Skin Panel - Station 297 to Station 439, Chem-Milled Steps
Between Stringer 4 Left and Stringer 4 Right Lap Joints - Inspection and Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Three operators reported cracks on six airplanes in the Body Station (STA) 297 to STA 439 crown skin panel.
The cracks are attributed to fatigue. Cracks may initiate at multiple locations on the interior surface, along the
chem-milled step edges above the stringer 4L or 4R lap splices of the skin, or above and below the stringers
3L, 2L, 1, 2R or 3R in the skin. Without inspection for cracks, multiple site cracks could link together and rapidly
progress through the skin. A long crack could result in pressure venting and a controlled decompression of the
airplane.
One reported crack was 10.75-inches long midway between STA 420 and STA 439. The crack was just above
the lap joint at stringer 4L common to the chem-milled step. The airplane had 24,631 flight cycles. On another
airplane the operator reported an opening in the fuselage approximately 12 inches by 18 inches above and aft
of the passenger entry doorway. One edge of the opening was common to the chem-milled step above stringer
4L. Additionally a 1.3 Inch crack was found in the skin forward of the opening in the adjacent skin bay also in
the chem-milled step above stringer 4L. The airplane had 22,450 flight cycles.
The cracks occur along locally thinned channels adjacent to the chem-mill steps. This local thinning occurs
during the chem-mill process and additional information has shown that thin channels are also present along
the edges of the chem-milled pockets adjacent to stringers 3L, 2L, 1, 2R and 3R.
This service bulletin gives inspections of the crown skin panel for cracks along all the chem-milled pocket edges
between stringers  4L and 4R, and between Body Stations 297 and 439. Accomplishment of this service bulletin
will make sure that cracks are found and repaired. This service bulletin allows inspections above the lap splices
at Stringer 4L and 4R to be terminated if  a preventive modification is installed. This service bulletin also allows
all inspections to be terminated if the entire skin panel is replaced with a new production skin panel between
Stringer 4L and 4R, and body stations 297 and 439.
Boeing Service Related Problem (SRP) 757-SRP-53-0368 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
9 of 195

### Page 10

ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., Compliance and Paragraph
1.F., Approval
YesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Parts/Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the exterior of the skin between the stringers 4L and 4R and between STA 297 and STA 439. Do
either a sliding probe external Eddy Current (EC) or a spot probe Medium Frequency Eddy Current (MFEC) for
cracks of the STA 297 to STA 439 crown skin panel at the edge of the chem-milled pockets at stringer S-4L and
S-4R lap joints and both sides of the stringers at S-3L to S-3R as described and at the times specified in Paragraph
1.E., Compliance. If any crack is found, contact The Boeing Company for repair instructions and do the repair.
Repeat the sliding probe EC, spot probe MFEC inspection at the times given in Paragraph 1.E., Compliance.
At the operators option, get access to the interior of the skin lap joints at stringers 4L and 4R, between STA 297
and STA 439 and do the preventive modification. If the ZONE 1 preventive modifications are installed, do post
modification LFEC and detailed inspections for cracks in the upper and lower skins common to the preventive
modification parts.
At the operators option, contact The Boeing Company for instructions to replace the crown skin panel between
stringers S-4L and S-4R, and, STA 297 and STA 439.
EFFECTIVITY
757-200 and 757-300 Airplanes. Refer to Paragraph 1.A.1., Airplanes, for the list of affected airplanes.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2011-01-15 is related to this service bulletin.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for 757 airplanes in warranty as of October 1, 2010. Please refer to
Paragraph 2.B., Industry Support Information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
10 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 11

MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
11 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 12 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
STA
439
STA
297
0000
CHEM-MILL-EDGE
FRAME  INSPECT FOR CRACKS IN THE
CROWN SKIN BETWEEN
STATION 297 AND STATION
439 AT THE CHEM-MILLED
POCKET EDGE ABOVE THE
LAP JOINT AT S-4L AND S-4R.
OPTIONAL: INSTALL
PREVENTIVE MODIFICATION
TYPICAL  AT S-4L AND S-4R, OR INSTALL
CRACK  REPLACEMENT CROWN SKIN
PANEL.
CROWN
SKIN
INSPECTION AREA
ABOVE LAP
SPLICE (TYPICAL)
STRINGER 4
LOWER SKIN
INSPECTION  2034160
AREA  TYPICAL CROWN SKIN CHEM-MILLED POCKET EDGE ABOVE S-4 LAP SPLICE
Original Issue: November 22, 2010
Revision 2: July 28, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53-0097
Work - See page 1 for details.  12 of 195

### Page 13 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
STA
439
STA
297
INSPECT FOR CRACKS IN THE
CHEM-MILL-EDGE  CROWN SKIN BETWEEN
STATION 297 AND STATION
FRAME  439 AT THE CHEM-MILLED
POCKET EDGE ABOVE AND
BELOW THE STRINGERS AT
S-3L THRU S-3R,
OPTIONAL: INSTALL
REPLACEMENT CROWN SKIN
PANEL.
TYPICAL
CRACK
CROWN
SKIN
INSPECTION AREA
ABOVE STRINGER
(TYPICAL)
STRINGER
INSPECTION AREA BELOW
STRINGER (TYPICAL)
INSPECTION  TYPICAL CROWN SKIN CHEM-MILLED POCKET EDGES  2342132
AREA  ADJACENT TO STRINGERS
Original Issue: November 22, 2010
Revision 2: July 28, 2015  Export Controlled ECCN: 9E991 - BOEING  757-53-0097
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  13 of 195

### Page 14

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
14 of 195
BOEING SERVICE BULLETIN 757-53-0097
BLANK PAGE

### Page 15

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-53-0097
Original Issue: November 22, 2010
Revision 2: July 28, 2015
ATA System: 5300
SUBJECT: FUSELAGE - Skin - Crown Skin Panel - Station 297 to Station 439, Chem-Milled Steps
Between Stringer 4 Left and Stringer 4 Right Lap Joints - Inspection and Modification
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is applicable to 757-200/-300 and -200 Boeing Special Freighter Airplanes in
3 Group(s). The Variable Numbers and Group Information for the applicable airplanes is given
below.
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
757-200 Airplanes without provision for an antenna in the crown skin
panels.
-1
757-200/-300 Airplanes with provision for an antenna in the crown
skin panels.
-2
757-200 Boeing Special Freighter Airplanes-3
Airplane Models:
757-200, 757-300
GroupVariable Number
1NA001 - NA028
1NA191 - NA199
3NA201 - NA204
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
15 of 195

### Page 16

GroupVariable Number
1NA205
3NA206 - NA213
1NA214
3NA215 - NA236
2NA237 - NA239
1NA301 - NA302
2NA303 - NA305
1NA341 - NA343
2NA344 - NA352
1NA391 - NA399
1NA401 - NA408
1NA441 - NA447
1NA501 - NA556
2NA557 - NA586
1NB001 - NB004
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB068
2NB069 - NB070
1NB071 - NB073
2NB079
1NB131 - NB140
2NB141 - NB148
2NB161 - NB162
2NB166 - NB168
1NB201 - NB203
2NB204
2NB221 - NB228
2NB230
2NB236
2NB239
2NB261 - NB267
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
16 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 17

GroupVariable Number
2NB291 - NB299
2NB301 - NB302
2NB311 - NB312
2NB321 - NB331
2NB421 - NB438
2NB446
2NB451 - NB454
2NB501 - NB523
2NB561
2NB571
2NB581 - NB583
1NC001 - NC033
1NC041 - NC042
2NC051 - NC052
2NC056 - NC062
2NC066 - NC084
2NC091 - NC094
2NC151
2NC161
1ND001 - ND003
2ND004 - ND007
1ND011 - ND019
2ND020 - ND059
2ND111 - ND113
2ND161 - ND199
1ND201 - ND202
2ND203
2ND221 - ND225
2ND241 - ND248
2ND301 - ND322
2ND401
1ND891
1NE001 - NE002
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
17 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 18

GroupVariable Number
2NE003 - NE008
1NE011 - NE016
2NE017 - NE088
2NE091 - NE094
2NE141 - NE150
1NE161 - NE163
2NE164 - NE177
2NE201 - NE204
2NE301 - NE302
2NE311 - NE325
2NJ001 - NJ004
2NJ031 - NJ032
2NJ551 - NJ555
2NL001 - NL002
2NL006 - NL017
2NL101 - NL109
2NL141
2NL601 - NL616
2NN001 - NN002
2NN051 - NN052
2NP901 - NP904
2NT201 - NT202
2NT231 - NT234
2NT237 - NT240
2NT242
2NT245 - NT248
2NT281 - NT289
2NT341 - NT347
2NT351 - NT360
2NT371 - NT373
2NT375 - NT379
2NT381 - NT386
2NT401 - NT409
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
18 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 19

GroupVariable Number
2NT411 - NT412
2NT426 - NT427
2NT431 - NT432
2NT436 - NT438
2NT441 - NT442
2NT446
2NT701 - NT769
2NT791 - NT796
2NT861 - NT862
2NT881 - NT885
2NT901 - NT916
2NT971 - NT985
2NU031 - NU038
2NU701 - NU705
2NU721 - NU728
2NU731 - NU732
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
Three operators reported cracks on six airplanes in the Body Station (STA) 297 to STA 439 crown skin
panel. The cracks are attributed to fatigue. Cracks may initiate at multiple locations on the interior
surface, along the chem-milled step edges above the stringer 4L or 4R lap splices of the skin or above
and below the stringers 3L, 2L, 1, 2R or 3R in the skin. Without inspection for cracks, multiple site
cracks could link together and rapidly progress through the skin. A long crack could result in pressure
venting and a controlled decompression of the airplane.
One reported crack was 10.75-inches long midway between STA 420 and STA 439. The crack was
just above the lap joint at stringer 4L common to the chem-milled step. The airplane had 24,631 flight
cycles. On another airplane the operator reported an opening in the fuselage approximately 12 inches
by 18 inches above and aft of the passenger entry doorway. One edge of the opening was common
to the chem-milled step above stringer 4L. Additionally a 1.3 Inch crack was found in the skin forward
of the opening in the adjacent skin bay also in the chem-milled step above stringer 4L. The airplane
had 22,450 flight cycles.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
19 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 20

The cracks occur along locally thinned channels adjacent to the chem-mill steps. This local thinning
occurs during the chem-mill process and additional information has shown that thin channels are also
present along the edges of the chem-milled pockets adjacent to stringers 3L, 2L, 1, 2R and 3R
This service bulletin gives inspections of the crown skin panel for cracks along chem-milled pocket
edges between stringers 4L, and 4R, and between Body Stations 297 and 439. Accomplishment of
this service bulletin will make sure that cracks are found and repaired. This service bulletin allows
inspections above the lap splices at Stringer 4L and 4R to be terminated if  a preventive modification
is installed. This service bulletin also allows all inspections to be terminated if the entire skin panel is
replaced with a new production skin panel between Stringer 4L and 4R, and body stations 297 and
439.
Boeing Service Related Problem (SRP) 757-SRP-53-0368 is related to this service bulletin.
Revision 1 was sent to clarify the inspection area of the chem-milled pocket edge.
Revision 2 is sent to increase compliance times and repeat intervals, to remove the detailed inspection
option and to add a preventive modification. This revision is also sent to add new inspection areas.
D. Description
Get access to the exterior of the skin between the stringers 4L and 4R and between STA 297 and STA
439. Do either a sliding probe external eddy current (EC) or a spot probe medium frequency eddy
current (MFEC) inspection for cracks of the STA 297 to STA 439 crown skin panel at the edge of the
chem-milled pockets above stringer S-4L, and S-4R lap joints and both sides of the stringers at S-3L
to S-3R as described and at the times specified in Paragraph 1.E., Compliance. If any crack is found,
contact The Boeing Company for damage removal and repair instructions and do the repair. Repeat
the sliding probe EC or spot probe MFEC inspection at the times given in Paragraph 1.E., Compliance
or accomplish the ZONE 1 preventive modification.
At the operators option, get access to the interior of the skin lap joints at stringers 4L and 4R, between
STA 297 and STA 439 and do the preventive modification. If the ZONE 1 preventive modifications are
installed, do post modification LFEC and detailed inspections for cracks in the upper and lower skins
common to the preventive modification parts.
At the operators option, contact The Boeing Company for instructions to replace the crown skin panel
between stringers S-4L and S-4R, and, STA 297 and STA 439.
Effects of this Revision on airplanes on which Original issue or Revision 1 were previously done:
None
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1, 3:
Affected Maintenance Zones
ZoneModel
223, 224757-200
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
20 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 21

Group 2:
Affected Maintenance Zones
ZoneModel
223, 224757-200, 757-300
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2011-01-15 is related to this service
bulletin. The effective date of AD 2011-01-15 is January 25, 2011.
Do the required actions in accordance with Paragraph 3. Accomplishment Instructions.
A logic diagram showing compliance tasks and compliance times is included as an aid in Appendix A,
B, C and D.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION number or an OPTION number, do all of the ACTION
numbers for that CONDITION number or OPTION number.
Inspection areas and methods required in Table 1 of the Original Issue or Revision 1 of this Service
Bulletin are the same inspection areas and methods as the ZONE 1 Inspections of Revision 2 of this
Service Bulletin. If the inspections have been accomplished in accordance with the Original Issue or
Revision 1 of this Service Bulletin, continue repetitive ZONE 1 Inspections in accordance with Revision
2 of this Service Bulletin.
Table 1: STA 297 to STA 439 crown skin panel - ZONE 1 - INSPECTIONS AND PREVENTIVE MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Occurs
Later)
ActionCondition
-Within 620 flight
cycles of a previ-
ous ZONE 1 slid-
ing probe EC in-
spection.
Before 18,000 total
flight cycles.
OPTION 1: Do PART 1:
ZONE 1 - EXTERNAL
SLIDING PROBE ED-
DY CURRENT (EC)
INSPECTION for
cracks. (a) (b) (c)
All Airplanes.
-Within 200 flight
cycles of a previ-
ous ZONE 1 spot
probe MFEC in-
spection.
Before 18,000 total
flight cycles.
OPTION 2: Do PART 2
: ZONE 1 - EXTERNAL
SPOT PROBE MEDI-
UM FREQUENCY ED-
DY CURRENT (MFEC)
INSPECTION for
cracks. (a) (b) (c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
21 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 22

Table 1: STA 297 to STA 439 crown skin panel - ZONE 1 - INSPECTIONS AND PREVENTIVE MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Occurs
Later)
ActionCondition
-Before further flight.CONDITION 1CONDITION 1: ANY
CRACK FOUND IN
ZONE 1.
(ACTION 1):
Contact The Boeing
Company for repair in-
structions and do the
repair.
620 flight cycles
after a ZONE 1
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 1 spot
probe MFEC in-
spection. (b) (c)
-CONDITION 1
(ACTION 2),
OPTION 1:
Repeat PART 1: ZONE
1 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in ZONE 1 areas not
covered by approved
repairs. (a)
620 flight cycles
after a ZONE 1
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 1 spot
probe MFEC in-
spection. (b) (c)
-CONDITION 1
(ACTION 2),
OPTION 2:
Repeat PART 2: ZONE
1 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in
ZONE 1 areas not cov-
ered by approved re-
pairs. (a)
-Refer to Table 2 for compliance informa-
tion.
CONDITION 1
(ACTION 3):
Do ZONE 2 - INSPEC-
TIONS in accordance
with Paragraph 1.E.,
Compliance Table 2.
(e)
-Refer to Table 3 for compliance informa-
tion.
CONDITION 1
(ACTION 4):
Do ZONE 3 - INSPEC-
TIONS in accordance
with Paragraph 1.E.,
Compliance Table 3. (f)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
22 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 23

Table 1: STA 297 to STA 439 crown skin panel - ZONE 1 - INSPECTIONS AND PREVENTIVE MODIFICATION
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever Occurs
Later)
ActionCondition
620 flight cycles
after a ZONE 1
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 1 spot
probe MFEC in-
spection. (b) (c)
-OPTION 1:
Repeat PART 1: ZONE
1 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in ZONE 1 areas not
covered by approved
repairs. (a) (d)
CONDITION 2: NO
CRACK FOUND IN
ZONE 1.
620 flight cycles
after a ZONE 1
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 1 spot
probe MFEC in-
spection. (b) (c)
-OPTION 2:
Repeat PART 2: ZONE
1 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in
ZONE 1 areas not cov-
ered by approved re-
pairs. (a) (d)
-Before further flight. (b) (g)OPTION 3:
Do PART 3: ZONE 1 -
PREVENTIVE MODIFI-
CATION. (h)
(a) It is not necessary to inspect the edge of the chem-mill pocket under an existing external repair or modifi-
cation doubler provided all of the following apply: 1.The repair doubler is 0.050 Inch or thicker 2024-T3
clad sheet; 2. The repair was approved by the FAA or by a Boeing Company Authorized Representative
who was authorized by the FAA to make such findings; 3. The repair doubler extends a minimum of three
rows of fasteners on each side of the chem-milled step in the circumferential direction.
(b) Accomplishment of PART 3: ZONE 1 - PREVENTIVE MODIFICATION is terminating action for the ZONE
1 inspections.
(c) Accomplishment of SKIN PANEL REPLACEMENT is terminating action for the ZONE 1, ZONE 2 and
ZONE 3 inspections.
(d) It is acceptable to change between external sliding probe EC and external spot probe MFEC inspection
options. Make sure each inspection is done within the repeat interval applicable to the inspection that was
last accomplished.
(e) Refer to Table 2 for subsequent ZONE 2 inspections.
(f) Refer to Table 3 for subsequent ZONE 3 inspections.
(g) PART 3: ZONE 1 - PREVENTIVE MODIFICATION can be deferred for accomplishment to a later date,
but can only be accomplished following either a PART 1 or PART 2 inspection, and before further flight.
(h) Refer to Table 4 for POST PREVENTIVE MODIFICATION SUPPLEMENTAL INSPECTIONS
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
23 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 24

Table 2: STA 297 to STA 439 crown skin panel - ZONE 2 - INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
(b)Within 120 days
after the Revision
2 date of this ser-
vice bulletin.
Before 42,000 total
flight cycles.
OPTION 4:
Do PART 4: ZONE 2 -
EXTERNAL SLIDING
PROBE EC INSPEC-
TION for cracks. (a)
Airplanes with one or
more of the following:
- any crack found in
ZONE 1.
- any repair installed
that covers the ZONE
1 inspection area. (b)Within 120 daysafter the Revision
2 date of this ser-
vice bulletin.
Before 42,000 total
flight cycles.
OPTION 5:
Do PART 5: ZONE 2 -
EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks. (a)
- preventive modifica-
tion has been installed
in accordance with
PART 3: ZONE 1 -
PREVENTIVE MODIFI-
CATION.
-Before further flight.CONDITION 3CONDITION 3: ANY
CRACK FOUND IN
ZONE 2.
(ACTION 1):
Contact The Boeing
Company for repair in-
structions and do the
repair.
620 flight cycles
after a ZONE 2
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 2 spot
probe MFEC in-
spection. (b)
-CONDITION 3
(ACTION 2),
OPTION 4:
Repeat PART 4: ZONE
2 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in ZONE 2 areas not
covered by an ap-
proved repair. (a) (c)
620 flight cycles
after a ZONE 2
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 2 spot
probe MFEC in-
spection. (b)
-CONDITION 3
(ACTION 2),
OPTION 5:
Repeat PART 5: ZONE
2 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in
ZONE 2 areas not cov-
ered by an approved
repair. (a) (c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
24 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 25

Table 2: STA 297 to STA 439 crown skin panel - ZONE 2 - INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
620 flight cycles
after a ZONE 2
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 2 spot
probe MFEC in-
spection. (b)
-OPTION 4:
Repeat PART 4: ZONE
2 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in ZONE 2 areas not
covered by an ap-
proved repair. (a) (c)
CONDITION 4: NO
CRACK FOUND IN
ZONE 2.
620 flight cycles
after a ZONE 2
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 2 spot
probe MFEC in-
spection. (b)
-OPTION 5:
Repeat PART 5: ZONE
2 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in
ZONE 2 areas not cov-
ered by an approved
repair. (a) (c)
(a) It is acceptable to change between external sliding probe EC and external spot probe MFEC inspection
options. Make sure each inspection is done within the repeat interval applicable to the inspection that was
last accomplished.
(b) Accomplishment of SKIN PANEL REPLACEMENT is terminating action for the ZONE 1, ZONE 2 and
ZONE 3 inspections.
(c) It is not necessary to inspect the edge of the chem-mill pocket under an existing ZONE 2 external repair
doubler provided all of the following apply: 1.The modification or repair doubler is 0.050 Inch or thicker
2024-T3 clad sheet; 2. The modification or repair was approved by the FAA or by a Boeing Company
Authorized Representative who was authorized by the FAA to make such findings; 3. The modification or
repair doubler extends a minimum of three rows of fasteners on each side of the chem-milled step in the
circumferential direction.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
25 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 26

Table 3: STA 297 to STA 439 crown skin panel - ZONE 3 - INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
(b)Within 120 days
after the Revision
2 date of this ser-
vice bulletin.
Before 48,000 total
flight cycles.
OPTION 6:
Do PART 6: ZONE 3 -
EXTERNAL SLIDING
PROBE MFEC INSPEC-
TION for cracks . (a)
Airplanes with one or
more of the following:
- any crack found in
ZONE 1.
- any repair installed
that covers the ZONE
1 inspection area. (b)Within 120 daysafter the Revision
2 date of this ser-
vice bulletin.
Before 48,000 total
flight cycles.
OPTION 7:
Do PART 7: ZONE 3 -
EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks. (a)
- preventive modifica-
tion has been installed
in accordance with
PART 3 - ZONE 1 -
PREVENTIVE MODIFI-
CATION .
-Before further flight.CONDITION 5CONDITION 5: ANY
CRACK FOUND IN
ZONE 3.
(ACTION 1):
Contact The Boeing
Company for repair in-
structions and do the
repair.
620 flight cycles
after a ZONE 3
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 3 spot
probe MFEC in-
spection. (b)
-CONDITION 5
(ACTION 2),
OPTION 6:
Repeat PART 6: ZONE
3 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in skin in ZONE 3 area
not covered by ap-
proved repairs. (a) (c)
620 flight cycles
after a ZONE 3
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 3 spot
probe MFEC in-
spection. (b)
-CONDITION 5
(ACTION 2),
OPTION 7:
Repeat PART 7: ZONE
3 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in skin
in ZONE 3 area not
covered by approved
repairs. (a) (c)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
26 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 27

Table 3: STA 297 to STA 439 crown skin panel - ZONE 3 - INSPECTIONS
Repeat Interval
(Not to Exceed)
Compliance Time
(Whichever Occurs Later)
ActionCondition
620 flight cycles
after a ZONE 3
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 3 spot
probe MFEC in-
spection. (b)
-OPTION 6:
Repeat PART 6: ZONE
3 - EXTERNAL SLID-
ING PROBE EC IN-
SPECTION for cracks
in skin in ZONE 3 areas
not covered by an ap-
proved repair. (a) (c)
CONDITION 6: NO
CRACK FOUND IN
ZONE 3.
620 flight cycles
after a ZONE 3
external sliding
probe EC inspec-
tion or 200 flight
cycles after a
ZONE 3 spot
probe MFEC in-
spection. (b)
-OPTION 7:
Repeat PART 7: ZONE
3 - EXTERNAL SPOT
PROBE MFEC INSPEC-
TION for cracks in skin
in ZONE 3 areas not
covered by an ap-
proved repair. (a) (c)
(a) It is acceptable to change between external sliding probe EC and external spot probe MFEC inspection
options. Make sure each inspection is done within the repeat interval applicable to the inspection that was
last accomplished.
(b) Accomplishment of SKIN PANEL REPLACEMENT is terminating action for the ZONE 1, ZONE 2 and
ZONE 3 inspections.
(c) It is not necessary to inspect the edge of the chem-mill pocket under an existing ZONE 3 external repair
doubler provided all of the following apply: 1.The modification or repair doubler is 0.050 Inch or thicker
2024-T3 clad sheet; 2. The modification or repair was approved by the FAA or by a Boeing Company
Authorized Representative who was authorized by the FAA to make such findings; 3. The modification or
repair doubler extends a minimum of three rows of fasteners on each side of the chem-milled step in the
circumferential direction.
Table 4: STA 297 to STA 439 crown skin panel - POST PREVENTIVE MODIFICATION SUPPLEMENTAL
INSPECTIONS
Repeat Interval (Not
to Exceed)
Compliance Time
(Whichever Occurs Earlier)
ActionCondition
-Before 50,000 total
flight cycles.
Within 39,000 flight
cycles after installa-
tion of preventive
modification.
Do PART 10: POST
PREVENTIVE MOD-
IFICATION SUPPLE-
MENTAL INSPEC-
TIONS for cracks.
Airplanes with pre-
ventive modification
installed in accor-
dance with PART 3:
ZONE 1 - PREVEN-
TIVE MODIFICA-
TION.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
27 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 28

Table 4: STA 297 to STA 439 crown skin panel - POST PREVENTIVE MODIFICATION SUPPLEMENTAL
INSPECTIONS
Repeat Interval (Not
to Exceed)
Compliance Time
(Whichever Occurs Earlier)
ActionCondition
-Before further flight.Contact The Boeing
Company for repair
and inspection in-
structions and do the
repair and inspec-
tions.
CONDITION 7: ANY
CRACK FOUND IN
POST PREVENTIVE
MODIFICATION
SUPPLEMENTAL
INSPECTIONS.
3,000 flight cycles.-Repeat PART 10:
POST PREVENTIVE
MODIFICATION
SUPPLEMENTAL
INSPECTIONS for
cracks.
CONDITION 8: NO
CRACK FOUND IN
POST PREVENTIVE
MODIFICATION
SUPPLEMENTAL
INSPECTIONS.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
In addition, the Manager of the FAA Los Angeles Aircraft Certification Office approves the action (i.e.
inspection or modification) defined in this service bulletin as an alternative method of compliance to
the requirements of paragraph (g) and (h) of AD 2011-01-15. All provisions of AD 2011-01-15 that are
not specifically referenced in the above statement remain fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
• Time to adjust to the workplace
• Time to schedule the work
• Time to inspect the work
• Time to cure the materials
• Time to make the parts
• Time to find the tools.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
28 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 29

Group 1-2:
PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251Access External
1.001.001FIGURE 2 - Inspection
1.251.25TOTAL FOR EACH AIRPLANE
Group 3:
PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251Access External
0.900.901FIGURE 4 - Inspection
1.151.15TOTAL FOR EACH AIRPLANE
Group 1-2:
PART 2: ZONE 1 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251Access External
3.003.001FIGURE 3 - Inspection
3.253.25TOTAL FOR EACH AIRPLANE
Group 3:
PART 2: ZONE 1 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251Access External
1.601.601FIGURE 5 - Inspection
1.851.85TOTAL FOR EACH AIRPLANE
Group 1-2:
PART 3: ZONE 1 - PREVENTIVE MODIFICATION
Elapsed HoursTask HoursNumber of PersonsTask
6.25 (a)25.00 (a)4 (a)PART 8: ACCESS - INTER-
NAL
16.0080.005Jack and Support Airplane
in Jig Position
PREVENTIVE MODIFICATION
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
29 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 30

Group 1-2:
PART 3: ZONE 1 - PREVENTIVE MODIFICATION
Elapsed HoursTask HoursNumber of PersonsTask
4.509.002FIGURE 16 - Inspection
4.2517.004FIGURE 19 - Inspection
9.2537.004FIGURE 22 - Inspection
(b)(b)-FIGURE 17 - Manufacture
(b)(b)-FIGURE 20 - Manufacture
(b)(b)-FIGURE 23 - Manufacture
10.7521.502FIGURE 18 - Installation
24.5049.002FIGURE 21 - Installation
52.00104.002FIGURE 24 - Installation
2.00105Remove Airplane From
Jack and Jig Position
6.25 (a)25.00 (a)4 (a)PART 9: CLOSE ACCESS
8.5017.002PART 10: ZONE 1 POST
MODIFICATION INSPEC-
TIONS
(c)(c)TOTAL FOR EACH AIRPLANE
(a) Number of Persons ,Task Hours and Elapsed Hours are given if Forward Galley and Forward Lavatory
are equipment on the airplane.
(b) Time to manufacture parts considered lost time in The Boeing Company estimates.
(c) Total time required dependent upon task required.
Group 3:
PART 3: ZONE 1 - PREVENTIVE MODIFICATION
Elapsed HoursTask HoursNumber of PersonsTask
2.004.002PART 8: ACCESS - INTER-
NAL
16.0080.005Jack and Support Airplane
in Jig Position
PREVENTIVE MODIFICATION
4.509.002FIGURE 16 - Inspection
3.0012.004FIGURE 25 - Inspection
11.0044.004FIGURE 28 - Inspection
(a)(a)-FIGURE 17 - Manufacture
(a)(a)-FIGURE 26 - Manufacture
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
30 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 31

Group 3:
PART 3: ZONE 1 - PREVENTIVE MODIFICATION
Elapsed HoursTask HoursNumber of PersonsTask
(a)(a)-FIGURE 29 - Manufacture
10.7521.502FIGURE 18 - Installation
25.5051.002FIGURE 27 - Installation
53.50107.002FIGURE 30 - Installation
2.0010.005Remove Airplane From
Jack and Jig Position
2.004.002PART 9: CLOSE ACCESS
8.7517.502PART 10: ZONE 1 POST
MODIFICATION INSPEC-
TIONS
(b)(b)TOTAL FOR EACH AIRPLANE
(a) Time to manufacture parts considered lost time in The Boeing Company estimates.
(b) Total time required dependent upon task required.
Group 1, 3:
PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.300.301FIGURE 6
0.300.30TOTAL FOR EACH AIRPLANE
Group 2:
PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.450.451FIGURE 7
0.450.45TOTAL FOR EACH AIRPLANE
Group 1, 3:
PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
0.900.901FIGURE 8
0.900.90TOTAL FOR EACH AIRPLANE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
31 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 32

Group 2:
PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
1.101.101FIGURE 9
1.101.10TOTAL FOR EACH AIRPLANE
Group 1:
PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
3.256.502FIGURE 10
3.256.50TOTAL FOR EACH AIRPLANE
Group 2:
PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
2.905.802FIGURE 11
2.905.80TOTAL FOR EACH AIRPLANE
Group 3:
PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
3.256.502FIGURE 12
3.256.50TOTAL FOR EACH AIRPLANE
Group 1:
PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
4.458.902FIGURE 13
4.458.90TOTAL FOR EACH AIRPLANE
Group 2:
PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
3.757.502FIGURE 14
3.757.50TOTAL FOR EACH AIRPLANE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
32 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 33

Group 3:
PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
Elapsed HoursTask HoursNumber of PersonsTask
4.458.902FIGURE 15
4.458.90TOTAL FOR EACH AIRPLANE
PART 10: POST PREVENTIVE MODIFICATION SUPPLEMENTAL INSPECTIONS
Elapsed HoursTask HoursNumber of PersonsTask
8.5017.002FIGURE 31
8.5017.00TOTAL FOR EACH AIRPLANE
Group 1-2:
SKIN PANEL REPLACEMENT
Elapsed HoursTask HoursNumber of PersonsTask
6.25 (a)25.00 (a)4 (a)Open access
16.0080.005Jack and Support Airplane
in Jig Position
118.75475.004Replace Crown Skin Panel
2.0010.005Remove Airplane From
Jack and Jig Position
6.2525.004Close access
154.75615.00TOTAL FOR EACH AIRPLANE
(a) Number of Persons ,Task Hours and Elapsed Hours are given if Forward Galley and Forward Lavatory
are equipment on the airplane.
Group 3:
SKIN PANEL REPLACEMENT
Elapsed HoursTask HoursNumber of PersonsTask
2.004.002Open access
16.0080.005Jack and Support Airplane
in Jig Position
118.75475.004Replace Crown Skin Panel
2.0010.005Remove Airplane From
Jack and Jig Position
2.004.002Close access
140.75573.00TOTAL FOR EACH AIRPLANE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
33 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 34

H. Weight and Balance Changes
Group 1-2:
Preventive Modification
Change in Moment (Pounds-
Inches)
Change in Weight (Pounds)Airplane
+17,700+48757-200
+10,000+48757-300
Group 3:
Preventive Modification
Change in Moment (Pounds-
Inches)
Change in Weight (Pounds)Airplane
+21,000+57757-200 Special Freighter
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Letter 757-SL-51-022
b. Boeing Service Related Problem (SRP) 757-SRP-53-0368
c. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2011-01-15
d. Standard Overhaul Practices Manual (SOPM) 20-41-02, 20-43-03, 20-50-01, 20-50-19
e. 757 Aircraft Maintenance Manual (AMM) 25-22-01, 25-22-02, 25-31-01, 25-41-01, 25-55-00
f. 757 Non-Destructive Testing (NDT) Manual Part 6, 51-00-16, Part 6, 53-00-06, Part 6, 53-00-10,
Part 6, 53-30-14
g. 757-200 Structural Repair Manual (SRM) 51-40-08, 53-00-01
h. 757-300 Structural Repair Manual (SRM) 51-40-08, 53-00-01
2. Data Supplied with this Service Bulletin:
None.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
34 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 35

3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
CROWN SKIN PANEL INSTL STA 297 TO STA 440 STR 4R TO
STR 4L
141N3310
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
35 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 36

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
36 of 195
BOEING SERVICE BULLETIN 757-53-0097
BLANK PAGE

### Page 37

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary for Each Airplane . Operators
are encouraged to share schedule requirements with Boeing for incorporation of the service bulletin.
The parts are subject to the terms and conditions of the Boeing standard purchase order
acknowledgment. Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
Group 1:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 2
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
NamePart Number
$20,316.00 (a)(a) Not available at
the date of Revi-
sion 2 of this Ser-
vice Bulletin.
Crown Skin Panel (a)141N3312-1
(a) The replacement of the Crown Skin Panel is an optional terminating action.
Group 2:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 2
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
NamePart Number
$20,316.00 (Option-
al $20,316.00) (c)
(c) Not available at
the date of Revi-
sion 2 of this Ser-
vice Bulletin.
Crown Skin Panel (c)141N3312-4 (Optional
654N0244-123 (a))
(Optional 141N3312Y4
(b))
$26,496.00 (Option-
al $26,496.00) (c)
(c) Not available at
the date of Revi-
sion 2 of this Ser-
vice Bulletin.
Crown Skin Panel (c)141N3312-7 (Optional
141N3312Y7 (d))
(a) Optional part 654N0244-123 is the same as 141N3312-4 except it has no chem-milled pockets and there
is 0.5 inch more panel on the fwd/aft ends.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
37 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 38

Group 2:
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 2
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 2 date of
this Service Bul-
letin (Calendar
Days)
NamePart Number
(b) 141N3312Y4 is the same as 141N3312-4 except there is 0.5 inch more panel on the forward/aft ends.
(c) The replacement of the Crown Skin Panel is an optional terminating action.
(d) 141N3312Y7 is the same as 141N3312-7 except there is 0.5 inch more panel on the fwd/aft ends.
Operators are encouraged to complete the survey provided in APPENDIX E of this service bulletin to
help Boeing predict the quantity and timing of the Boeing Supplied Kits/Parts.
NOTE: A 141N3312-4 or a 141N3312-7 panel, or its option are structurally interchangeable if hand
polishing is not a concern.
B. Industry Support Information
Boeing warranty remedies are available for 757 airplanes in warranty as of October 1, 2010. For labor
task hour and material reimbursement for airplanes in warranty as of that date, send a warranty claim
to Boeing Fleet Support Contracts - Warranty.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
Group 1-2:
NotesNameQTYPart Number/Specification
(a) (b) (c)Rivet760BACR15CE6D5 (BACR15FV6KE5 Option-
al)
(a) (b) (c)Rivet600BACR15CE6D6 (BACR15FV6KE6 Option-
al)
(a) (b) (c)Rivet500BACR15CE6D7 (BACR15FV6KE7 Option-
al)
(a) (b) (c)Rivet250BACR15CE6D8 (BACR15FV6KE8 Option-
al)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
38 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 39

Group 1-2:
NotesNameQTYPart Number/Specification
(a) (b) (c)Rivet20BACR15CE6D9 (BACR15FV6KE9 Option-
al)
(a) (b) (c)Rivet15BACR15CE6D10 (BACR15FV6KE10 Op-
tional)
(a) (b) (c)Rivet10BACR15CE6D11 (BACR15FV6KE11 Op-
tional)
Refer to 757-200 SRM
51-40-08, or 757-300
SRM 51-40-08.
Countersink Repair Washer-
37 x 15 inchesDoubler A (STA 297 thru
STA 324 at S-4L)
12024-T3 clad sheet 0.063 inch thick
37 x 7 inchesFiller B (STA 297 thru STA
324 at S-4L)
12024-T3 clad sheet 0.063 inch thick
73 x 15 inchesDoubler C (STA 377.7 thru
STA 440 at S-4L)
12024-T3 clad sheet 0.063 inch thick
73 x 7 inchesFiller D (STA 377.7 thru STA
440 at S-4L)
12024-T3 clad sheet 0.063 inch thick
153 x 22 inchesDoubler H (STA 297 thru
STA 440 at S-4R)
12024-T3 clad sheet 0.063 inch thick.
153 x 10 inchesFiller I (STA 297 thru STA
440 at S-4R)
12024-T3 clad sheet 0.063 inch thick
Refer to SOPM 20-43-
03.
Chemical Conversion Coat-
ing
4 QuartsType 2, Class A
(d)Primer4 QuartsBMS 10-11 Type 1
(d)Sealant125
Ounces
BMS 5-95
(d)Corrosion Inhibiting Com-
pound
4 QuartsBMS 3-23
(a) There are more parts than necessary
(b) Longer rivets may be required depending on specific location. More rivet quantities may be required de-
pending on specific location.
(c) Use BACR15FT7KE( ) protruding head rivets if oversize is necessary at existing locations.
(d) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
39 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 40

Group 3:
NotesNameQTYPart Number/Specification
(a) (b) (d)Rivet710BACR15CE6D5 (BACR15FV6KE5 Option-
al)
(a) (b) (d)Rivet625BACR15CE6D6 (BACR15FV6KE6 Option-
al)
(a) (b) (d)Rivet480BACR15CE6D7 (BACR15FV6KE7 Option-
al)
(a) (b) (d)Rivet335BACR15CE6D8 (BACR15FV6KE8 Option-
al)
(a) (b) (d)Rivet100BACR15CE6D9 (BACR15FV6KE9 Option-
al)
(a) (b) (d)Rivet25BACR15CE6D10 (BACR15FV6KE10 Op-
tional)
(a) (b) (d)Rivet10BACR15CE6D11 (BACR15FV6KE11 Op-
tional)
Refer to 757-200 SRM
51-40-08, or 757-300
SRM 51-40-08.
Countersink Repair Washer-
(a) (c) (e)Bolt5BACB30NX6K8
(a) (c) (e)Bolt10BACB30NX6K9
(a) (c) (e)Bolt15BACB30NX6K10
(a) (c) (f)Collar30BACC30X
(a) (c) (e)Bolt40BACB30NW6K8
(a) (c) (e)Bolt25BACB30NW6K9
(a) (c) (g)Collar65BACC30M
37 x 15 inchesS-4L Doubler A12024-T3 clad sheet 0.063 inch thick
37 x 7 inchesFiller B12024-T3 clad sheet 0.063 inch thick
73 x 15 inchesDoubler E12024-T3 clad sheet 0.063 inch thick
73 x 7 inchesFiller F12024-T3 clad sheet 0.063 inch thick
21 x 20 inchesTripler G12024-T3 clad sheet 0.063 inch thick
153 x 22 inchesDoubler J12024-T3 clad sheet 0.063 inch thick
153 x 10 inchesFiller K12024-T3 clad sheet 0.063 inch thick
42 x 20 inchesTripler L12024-T3 clad sheet 0.063 inch thick
Refer to SOPM 20-43-
03 for material sources.
Chemical Conversion Coat-
ing
4 QuartsType 2, Class A
(h)Primer4 QuartsBMS 10-11 Type 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
40 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 41

Group 3:
NotesNameQTYPart Number/Specification
(h)Sealant125
Ounces
BMS 5-95
(h)Corrosion Inhibiting Com-
pound
4 QuartsBMS 3-23
(a) There are more parts than necessary
(b) Longer rivets may be required depending on specific location. More rivet quantities may be required de-
pending on specific location.
(c) Longer bolts may be required depending on specific location. More bolt and collar quantities may be required
depending on specific location.
(d) Use BACR15FT7KE( ) protruding head rivets if oversize is necessary at existing locations.
(e) Install 1/64 or 1/32 oversize bolts as necessary
(f) Use BACC30AC collar for 1/32 oversize bolts
(g) Use BACC30R collar for 1/32 oversize bolts.
(h) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Although no special tools are required, the sliding probe EC procedure given in 757 NDT Part 6,
53-30-14 requires a sliding probe that may not be in the operator's inventory. Refer to 757 NDT Part
6, 53-30-14 for information about the sliding probe part number.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
41 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 42

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
42 of 195
BOEING SERVICE BULLETIN 757-53-0097
BLANK PAGE

### Page 43

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Values for structural fasteners are given in 757 Structural Repair Manual,
Chapter 51.
4. Use the approved fastener, process and material substitutions in accordance with
SRM Chapter 51.
5. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51. Refer to SOPM 20-50-01 for alternate
full threaded fasteners (screws) needed for installation in this service bulletin.
6. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
43 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 44

8. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
9. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
10. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
11. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
12. Refer to Appendix A, B, C and D for logic diagram(s). Logic diagrams are provided
as an aid only. Information contained in Paragraph 1.E., Compliance is the primary
source for compliance times. Information in Paragraph 3.B., Work Instructions is the
primary source for tasks required for compliance.
13. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION number or an
OPTION number, do all of the ACTION numbers for that CONDITION number or
OPTION number.
14. The compliance times for the actions in Paragraph 3.B., WORK INSTRUCTIONS
are in Paragraph 1.E., Compliance.
15. Some steps in the Work Instructions are identified as Required for Compliance (RC).
If this service bulletin is mandated by an Airworthiness Directive (AD), then the steps
identified as RC must be done to comply with the AD. Alternative procedures for
steps not identified with RC can be used if the RC steps can still be done as specified,
and the airplane can be put back in a serviceable condition. An Alternative Method
of Compliance (AMOC) is not necessary for deviations to steps that are not identified
as RC.
B. WORK INSTRUCTIONS
1. RC - Do one of the following inspection options:
a. OPTION 1: Do PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EC INSPECTION for cracks.
b. OPTION 2: Do PART 2: ZONE 1 - EXTERNAL SPOT PROBE MFEC INSPECTION for cracks.
2. CONDITION 1: ANY CRACK FOUND IN ZONE 1.
a. RC - CONDITION 1 (ACTION 1): Contact The Boeing Company for repair instructions and
do the repair.
b. CONDITION 1 (ACTION 2): Do one of the following options:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
44 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 45

(1) OPTION 1: Repeat PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 1 areas not covered by approved repairs..
(2) OPTION 2: Repeat PART 2: ZONE 1 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 1 areas not covered by approved repairs..
c. CONDITION 1 (ACTION 3): Do ZONE 2 - INSPECTIONS.
d. CONDITION 1 (ACTION 4): Do ZONE 3 - INSPECTIONS.
3. CONDITION 2: NO CRACK FOUND IN ZONE 1
a. RC - Do one of the following repeat inspection or terminating modification options:
(1) OPTION 1: Repeat PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 1 areas not covered by approved repairs..
(2) OPTION 2: Repeat PART 2: ZONE 1 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 1 areas not covered by approved repairs.
(3) OPTION 3: Do PART 3: ZONE 1 - PREVENTIVE MODIFICATION.
4. If any crack was found in ZONE 1, or any repair installed that covers the ZONE 1 inspection area,
or preventive modification has been installed in accordance with PART 3: ZONE 1 - PREVENTIVE
MODIFICATION; do one of the following inspection options:
a. OPTION 4: Do PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION for cracks.
b. OPTION 5: Do PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION for cracks.
5. CONDITION 3: ANY CRACK FOUND IN ZONE 2.
a. RC - CONDITION 3 (ACTION 1): Contact The Boeing Company for repair instructions and
do the repair.
b. RC - CONDITION 3 (ACTION 2): Do one of the following repeat inspection options:
(1) OPTION 4: Repeat PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 2 areas not covered by approved repairs.
(2) OPTION 5: Repeat PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 2 areas not covered by approved repairs.
6. CONDITION 4: NO CRACK FOUND IN ZONE 2.
a. RC - Do one of the following repeat inspection options:
(1) OPTION 4: Repeat PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 2 areas not covered by approved repairs.
(2) OPTION 5: Repeat PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 2 areas not covered by approved repairs.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
45 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 46

7. If any crack was found in ZONE 1, or any repair installed that covers the ZONE 1 inspection area,
or preventive modification has been installed in accordance with PART 3: ZONE 1 - PREVENTIVE
MODIFICATION; do one of the following inspection options:
a. OPTION 6: Do PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION for cracks.
b. OPTION 7: Do PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION for cracks.
8. CONDITION 5: ANY CRACK FOUND IN ZONE 3.
a. RC - CONDITION 5 (ACTION 1): Contact The Boeing Company for repair instructions and
do the repair.
b. RC - CONDITION 5 (ACTION 2): Do one of the following repeat inspection options:
(1) OPTION 6: Repeat PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 3 areas not covered by approved repairs.
(2) OPTION 7: Repeat PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 3 areas not covered by approved repairs.
9. CONDITION 6: NO CRACK FOUND IN ZONE 3.
a. RC - Do one of the following repeat inspection options:
(1) OPTION 6: Repeat PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
for cracks in ZONE 3 areas not covered by approved repairs.
(2) OPTION 7: Repeat PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
for cracks in ZONE 3 areas not covered by approved repairs.
10. CONDITION 7: ANY CRACK FOUND IN POST PREVENTIVE MODIFICATION SUPPLEMENTAL
INSPECTIONS
a. RC - CONDITION 7 (ACTION 1): Contact The Boeing Company for repair instructions and
do the repair. Obtain supplemental inspections from The Boeing Company for the repair and
incorporate them in post-repair inspection plans.
11. CONDITION 8: NO CRACK FOUND IN POST PREVENTIVE MODIFICATION SUPPLEMENTAL
INSPECTIONS
a. RC - Repeat PART 10: POST PREVENTIVE MODIFICATION SUPPLEMENTAL
INSPECTIONS.
12. SKIN PANEL REPLACEMENT
NOTE: Skin panel replacement is an optional terminating action for ZONE 1, ZONE 2 and ZONE
3 inspections.
a. Contact The Boeing Company for instructions to replace the crown skin panel between STA
297 and STA 439, S-4L to S-4R, and do the instructions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
46 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 47

PART 1: ZONE 1 - EXTERNAL SLIDING PROBE EDDY CURRENT (EC) INSPECTION
1. Group 1-2:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 AND
STA 439.
2. Group 3:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 AND
STA 418.
3. Group 1-2:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
from STA 297 to STA 324, and from STA 377.7 to STA 439 at chem-milled pocket edges adjacent
to S-4L, and from STA 297 to STA 439 at chem-milled pocket edges adjacent to S-4R in accordance
with FIGURE 2.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
4. Group 3:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
from STA 297 to STA 324, and from STA 377.7 to STA 418 at chem-milled pocket edges adjacent
to S-4L, and from STA 297 to STA 418 at chem-milled pocket edges adjacent to S-4R in accordance
with FIGURE 4.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 2: ZONE 1 - EXTERNAL SPOT PROBE MEDIUM FREQUENCY EDDY CURRENT (MFEC)
INSPECTION
1. Group 1-2:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 AND
STA 439.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
47 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 48

2. Group 3:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 AND
STA 418.
3. Group 1-2:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks from STA 297 to STA 324, and from STA 377.7 to STA 439 at chem-milled
pocket edges adjacent to S-4L, and from STA 297 to STA 439 at chem-milled pocket edges
adjacent to S-4R in accordance with FIGURE 3.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
4. Group 3:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks from STA 297 to STA 324, and from STA 377.7 to STA 418 at chem-milled
pocket edges adjacent to S-4L, and from STA 297 to STA 418 at chem-milled pocket edges
adjacent to S-4R in accordance with FIGURE 5.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 3: ZONE 1 - PREVENTIVE MODIFICATION
1. Do PART 8: ACCESS - INTERNAL.
NOTE: For preventive modification installation The Boeing Company recommends that the left
side and right side modifications are done separately. Do the fastener removals,
inspections and installation of all modification parts on one side of the airplane before
doing the modification to the opposite side.
2. Support the airplane in the jig position, refer to 757-200 SRM 51-50-02 or 757-300 SRM 51-50-02
as accepted procedures.
3. RC - Remove fasteners and do an open hole EC inspection to make sure there are no cracks at
fastener hole locations in accordance with:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
48 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 49

Right SideLeft Side
FIGURE 22 and FIGURE 28FIGURE 16, FIGURE 19 and FIGURE 25.
4. Group 1-2:
RC - Manufacture the preventive modification doublers, fillers and countersink repair washers in
accordance with:
Right SideLeft Side
FIGURE 23.FIGURE 17 and FIGURE 20
5. Group 3:
RC - Manufacture the preventive modification doublers, fillers, triplers and countersink repair
washers in accordance with:
Right SideLeft Side
FIGURE 29.FIGURE 17 and FIGURE 26
6. Group 1-2:
RC - Install the preventive modification doublers, fillers and countersink repair washers in
accordance with:
Right SideLeft Side
FIGURE 24.FIGURE 18 and FIGURE 21
7. Group 3:
RC - Install the preventive modification doublers, fillers, triplers and countersink repair washers in
accordance with:
Right SideLeft Side
FIGURE 30.FIGURE 18 and FIGURE 27
8. Remove the airplane from the jig position, refer to 757-200 SRM 51-50-02 or 757-300 SRM 51-50-02
as accepted procedures.
9. Do PART 9: CLOSE ACCESS - INTERNAL
10. Do PART 10: POST PREVENTIVE MODIFICATION SUPPLEMENTAL INSPECTIONS.
PART 4: ZONE 2 - EXTERNAL SLIDING PROBE EC INSPECTION
1. Group 1, 3:
Get external access to the crown skin panel at stringers S-3L between STA 324 and STA 378.
2. Group 2:
Get external access to the crown skin panel at stringers S-3L between STA 324 and STA 378,
and at stringers S-2L and S-3R between STA 418 and STA 439.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
49 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 50

3. Group 1, 3:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
from STA 324 to STA 378 at chem-milled pocket edges adjacent to S-3L in accordance with
FIGURE 6.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
4. Group 2:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
from STA 324 to STA 378 at chem-milled pocket edges adjacent to S-3L, and from STA 418 to
STA 439 adjacent to s-2L and S-3R in accordance with FIGURE 7.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 5: ZONE 2 - EXTERNAL SPOT PROBE MFEC INSPECTION
1. Group 1, 3:
Get external access to the crown skin panel at stringers S-3L between STA 324 and STA 378.
2. Group 2:
Get external access to the crown skin panel at stringers S-3L between STA 324 and STA 378,
and at stringers S-2L and S-3R between STA 418 and STA 439.
3. Group 1, 3:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks from STA 324 to STA 378 at chem-milled pocket edges adjacent to S-3L in
accordance with FIGURE 8.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
50 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 51

3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
4. Group 2:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks from STA 324 to STA 378 at chem-milled pocket edges adjacent to S-3L,
and from STA 418 to STA 439 adjacent to S-2L and S-3R in accordance with FIGURE 9.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 6: ZONE 3 - EXTERNAL SLIDING PROBE EC INSPECTION
1. Get external access to the crown skin panel from stringer S-3L to S-3R and between SAT 297 to
STA 439.
2. Group 1:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
between STA 297 to STA 439 from stringer S-3L to S-3R in accordance with FIGURE 10.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
3. Group 2:
RC - Do an external sliding probe Eddy Current (EC) inspection of the crown skin panel for cracks
between STA 297 to STA 439 from stringer S-3L to S-3R in accordance with FIGURE 11.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
51 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 52

4. Group 3:
RC - Do an external sliding probe EC inspection of the crown skin panel for cracks between STA
297 to STA 418 from stringer S-3L to S-3R in accordance with FIGURE 12.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 7: ZONE 3 - EXTERNAL SPOT PROBE MFEC INSPECTION
1. Get external access to the crown skin panel from stringer S-3L to S-3R and between SAT 297 to
STA 439.
2. Group 1:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks between STA 297 to STA 439 from stringer S-3L to S-3R in accordance with
FIGURE 13.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
3. Group 2:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks between STA 297 to STA 439 from stringer S-3L to S-3R in accordance with
FIGURE 14.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
52 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 53

4. Group 3:
RC - Do an external spot probe Medium Frequency Eddy Current (MFEC) inspection of the crown
skin panel for cracks between STA 297 to STA 418 from stringer S-3L to S-3R in accordance with
FIGURE 15.
NOTE: It is not necessary to inspect the chem-mill pocket edge under an existing external repair
or modification doubler provided all of the following apply:
1. The repair doubler is made from 0.050 Inch or thicker 2024-T3 clad sheet.
2. The repair was approved by the FAA or by a Boeing Company Authorized
Representative who was authorized by the FAA to make such findings.
3. The repair extends a minimum of three rows of fasteners on each side of the
chem-milled step in the circumferential direction.
PART 8: INTERNAL ACCESS
1. Group 1-2:
Remove the following as needed to get internal access to the crown skin panel from STA 297 to
STA 439, stringer S-5L to stringer S-5R, as necessary to accomplish the skin modification.
– The forward galley. Refer to 757 AMM 25-31-01 as an accepted procedure.
– The forward lavatory. Refer to 757 AMM 25-41-01 as an accepted procedure.
– The ceiling lining and insulation. Refer to 757 AMM 25-22-01 and 757 AMM 25-22-02 as
accepted procedures.
NOTE: It is possible that life rafts that are mounted above the lowered ceiling panels in some
airplanes, these will need to be removed too.
2. Group 3:
Do the following to get internal access to the crown skin panel from STA 297 to STA 439, stringer
S-5L to stringer S-5R, as necessary to accomplish the skin modification.
a. Remove the cargo barrier restraint straps common to the modification.
b. Remove the ceiling lining and insulation. Refer to 757 AMM 25-55-00 as an accepted
procedure.
c. Remove attach straps common to the modification.
PART 9: CLOSE ACCESS - INTERNAL
1. Group 1-2:
Do the following to install all passenger cabin equipment removed for access to the crown skin
panel.
– Install the ceiling lining and insulation. Refer to 757 AMM 25-22-01 and 757 AMM 25-22-02
as accepted procedures.
NOTE: Install life rafts above lowered ceiling if previously removed.
– Install the forward lavatory. Refer to 757 AMM 25-41-01 as an accepted procedure.
– Install the forward galley. Refer to 757 AMM 25-31-01 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
53 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 54

2. Group 3:
Do the following to install all cargo compartment equipment removed for access to the crown skin
panel.
a. Install attach straps common to the modification.
b. Install the ceiling lining and insulation. Refer to 757 AMM 25-55-00 as an accepted procedure.
c. Install the cargo barrier restraint straps common to the modification.
PART 10: POST PREVENTIVE MODIFICATION SUPPLEMENTAL INSPECTIONS
1. Group 1-2:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 and
STA 439.
2. RC - Do an EC and detailed inspections for cracks in accordance with FIGURE 31.
3. Group 3:
Get external access to the crown skin panel at stringers S-4L and S-4R between STA 297 and
STA 418.
4. RC - Do an EC and detailed inspections for cracks in accordance with FIGURE 32.
5. RC - If any crack is found, contact the Boeing Company for repair instructions and do the repair.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2: July 28, 2015
54 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 55

FIGURE 1: THIS FIGURE WAS DELETED AT REVISION 2
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2 July 28, 2015
55 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 56 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
This Figure applies only to: Group 1-2.
STA
439.00
STA  - S-4R
365.25  S-1
297.00  STA  _ S-4L
_S-10L
- S-20L
S-4L
STA
297  310.5  STA  STA  324  333.45  STA  STA  350  365.25  STA
INSPECTION AREA  -WD
2034288
FIGURE 2: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SLIDING PROBE EC
INSPECTION
(SHEET 1 OF 3)
Original Issue: November 22, 2010
Revision 2 July 28, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53-0097
Work - See page 1 for details.  56 of 195

### Page 57 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
- S-4R
— S-3R
• S-2R
S-4L
STA
365.25  STAT  SIA  STA
439
FWD
A INSPECTION AREA
2034287
FIGURE 2: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SLIDING PROBE EC
INSPECTION
(SHEET 2 OF 3)
Original Issue: November 22, 2010
Revision 2 July 28, 2015  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  757-53-0097
Work - See page 1 for details.  57 of 195

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--CROWN SKIN PANELInspect1
(a) Do an external sliding probe EC inspection for cracks in the crown skin panel along the edge of the chem-
milled pocket above the lap joint in accordance with 757 NDT Part 6, 53-30-14.
FIGURE 2: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SLIDING PROBE EC
INSPECTION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: November 22, 2010
757-53-0097Revision 2 July 28, 2015
58 of 195
BOEING SERVICE BULLETIN 757-53-0097

### Page 59 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
This Figure applies only to: Group 1-2.
STA
439.00
STA  - S-4R
365.25  • S-1
STA  - S-4L
297.00
-S-10L
- S-20L
S-4R
S-3R -
S-2R -
S-1 -
S-2L
S-3L -
S-4L
STA  297  310.5  STA  STA  324  333.45  STA  STA  350  365.25  STA
INSPECTION AREA
A  FWD
FIGURE 3: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SPOT PROBE MFEC
INSPECTION
(SHEET 1 OF 3)
Original Issue: November 22, 2010
Revision 2 July 28, 2015  Export Controlled ECCN: 9E991 - BOEING  757-53-0097
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  59 of 195

### Page 60 (OCR)

BOEING SERVICE BULLETIN 757-53-0097
- S-4R
— S-3R
S-2R
- S-2L
- S-3L
S-4L
365.25  STA  STA  STA  STA
395  418  STA
439
FWD
INSPECTION AREA
2035891
FIGURE 3: STA 297 TO STA 439 CROWN SKIN PANEL - ZONE 1 - EXTERNAL SPOT PROBE MFEC
INSPECTION
(SHEET 2 OF 3)
Original Issue: November 22, 2010
Revision 2 July 28, 2015  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  757-53-0097
Work - See page 1 for details.  60 of 195

The text continues at https://openairdocs.org/service-documents/boeing/sb-757-53-0097/file/8d29ec19d662.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
