# Boeing Special Attention Service Bulletin 757-54-0049: U.S. DOT/FAA - SB-757-54-0049-02

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2012-0809; AD 2013-04-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-54-0049](https://openairdocs.org/service-documents/boeing/sb-757-54-0049.md)
- Title as filed: U.S. DOT/FAA - SB-757-54-0049-02
- Pages: 78
- PDF: https://openairdocs.org/files/sha256/99/a8/99a88085a6caf581b174263c4666d167cf6a39cfd686324a93c0aab85d14a357
- Page: https://openairdocs.org/service-documents/boeing/sb-757-54-0049/file/99a88085a6ca

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-54-0049
Original Issue: July 16, 2007
Revision 2: July 27, 2011
ATA System: 5451
SUBJECT: NACELLES/PYLONS - Nacelle Strut - Thrust Reverser Aft Hinge Fitting Modification
- Rolls Royce RB211-535E Engines
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2007 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
1 of 78
3.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
2 of 78
BOEING SERVICE BULLETIN 757-54-0049
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 4
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 1 8
G. Manpower .............................................. 1 9
H. Weight and Balance Changes .................................... 2 0
I. Electrical Load Data ......................................... 2 0
J. References .............................................. 2 0
1. Existing Data: ......................................... 2 0
2. Data supplied with this Service Bulletin: ........................... 2 1
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 1
K. Publications Affected ........................................ 2 1
L. Interchangeability and Intermixability of Parts ........................... 2 1
2. MATERIAL INFORMATION ........................................ 2 3
A. Material - Price and Availability ................................... 2 3
B. Industry Support Information .................................... 2 4
C. Parts Necessary For Each Airplane ................................. 2 4
1. Kits/Parts: ........................................... 2 4
2. Parts and Materials Supplied by the Operator: ........................ 2 5
3. Parts Modified and Reidentified: ............................... 2 5
4. Parts Removed and Not Replaced: .............................. 2 6
D. Parts Necessary to Change Spares ................................. 2 6
E. Special Tooling - Price and Availability ............................... 2 6
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 6
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 7
A. GENERAL INFORMATION ..................................... 2 7
B. WORK INSTRUCTIONS ....................................... 2 9
FIGURE 1: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
[Group 1, Configuration 1] ................................... 3 4
FIGURE 2: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
[Group 1, Configuration 1] ................................... 3 7
FIGURE 3: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - TRIM [Group 1,
Configuration 1] ......................................... 4 0
FIGURE 4: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - TRIM [Group 1,
Configuration 1] ......................................... 4 4
FIGURE 5: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION [Group 1, Configuration
1 ]  ................................................ 4 8
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
3 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 4

FIGURE 6: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION [Group 1, Configuration
1 ]  ................................................ 5 1
FIGURE 7: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION [Group 1, Configuration 1] .................. 5 4
FIGURE 8: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION [Group 1, Configuration 1] .................. 5 7
FIGURE 9: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING UPPER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION [Group 1, Configuration
1 ]  ................................................ 6 0
FIGURE 10: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING UPPER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION [Group 1, Configuration
1 ]  ................................................ 6 3
FIGURE 11: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING UPPER FASTENER HOLES
- FASTENER INSTALLATION ................................. 6 6
FIGURE 12: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING UPPER FASTENER HOLES
- FASTENER INSTALLATION ................................. 6 9
FIGURE 13: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - REMOVAL AND INTERIM
INSTALLATION [Group 1, Configuration 1] .......................... 7 2
FIGURE 14: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - REMOVAL AND INTERIM
INSTALLATION [Group 1, Configuration 1] .......................... 7 5
APPENDIX A: AFT HINGE FITTING FASTENER STACKUP ........................ 7 8
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
4 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-54-0049Original Issue: July 16, 2007
Revision 2: July 27, 2011
ATA System: 5451
SUBJECT: NACELLES/PYLONS - Nacelle Strut - Thrust Reverser Aft Hinge Fitting Modification
- Rolls Royce RB211-535E Engines
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on the airplane(s) changed in accordance with Revision 1 of this service bulletin.
Federal Aviation Administration (FAA) Airworthiness Directive AD 2008-13-20 is related to this service bulletin.
REASON FOR REVISION
This revision is sent to inform operators that an aft hinge fitting designed with the trim already in it, is being made
available as an option to trimming an existing or new hinge fitting.
These sections were changed:
1. Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added optional 311N5148-4 Hinge Fitting
and optional replacement shim.
2. Paragraph 3.A., General Information, updated the general notes.
3. Paragraph 3.B., Work Instructions, Part II - Inspection, added optional 311N5148-4 fitting to step 1.a,
1.e.(2)(b), 2.a., and 2.e.(2)(b).
4. Paragraph 3.B. Work Instructions, Part III - Preventive Modification, added option to use a new 311N5148-4
fitting designed with the trim already in it, under Step 4.b. Option 2, substeps (2) and (5).
5. Figures 13 and 14, added optional 311N5148-4 fitting to step 6, added footnote (c) with option to use BMS
5-95 instead of BMS 5-45, and added footnote (d) with option to install a replacement shim.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
5 of 78

### Page 6

REVISION HISTORY
July 16, 2007Original Issue:
September 23, 2009Revision 1:
July 27, 2011Revision 2:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
6 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-54-0049Original Issue: July 16, 2007
Revision 2: July 27, 2011
ATA System: 5451
SUBJECT: NACELLES/PYLONS - Nacelle Strut - Thrust Reverser Aft Hinge Fitting Modification
- Rolls Royce RB211-535E Engines
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
You cannot make the changes given in this service bulletin unless the changes given in Service Bulletin
757-54-0015 R3 are made prior to or concurrent with this service bulletin. The 757-54-0015 service bulletin
replaced an older aft hinge fitting and attachment bolts with the current part numbers on airplanes line numbers
through 241. The changes given in Service Bulletin 757-54-0015 were made on airplanes after line number 241,
before delivery.
BACKGROUND
This service bulletin gives instructions to do a detailed inspection and preventive modification on the thrust
reverser aft hinge fittings, and hinge fitting attachment bolts. Attachment bolts have been reported to fail at the
thrust reverser aft hinge fittings. The hinge has integral fail-safe features, but loss of the entire four bolt pattern
constitutes complete loss of the load path. Loss of the load path could result in the departure of the thrust reverser
from the airplane which could result in damage to the airplane and hazards to persons or property on the ground.
Boeing has received 13 reports of 14 separate incidents of bolt failure at the thrust reverser aft hinge fittings.
All of the reported incidents occurred on airplanes with Rolls Royce RB211-535E engines. Of the 14 incidents
there were 9 hinges with 1 out of 4 bolts failed, 2 hinges with 2 out of 4 bolts failed, and 3 hinges with 3 out of
4 bolts failed.
The possible causes of the bolt failure can be attributed to high operational loads, contact loads caused by
possible interference between the thrust reverser hinge and the hinge beam, and the 4 attachment bolts are
installed with washers that can ride the radius of the hinge fitting spotface.
As a part of a service bulletin validation program, this change was completed on airplane NT744 by Service
Bulletin 757-54-0049 Validation Copy 01 before the initial release of this service bulletin. The change completed
on airplane NT744 by Service Bulletin 757-54-0049 Validation Copy 01 is equivalent to the initial release of this
service bulletin.
Boeing Service Related Problem (SRP) 757-SRP-54-0098 is related to this service bulletin.
ACTION (PRR 55029-R)
(PRR 54530-267RS)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
7 of 78

### Page 8

Inspections:
Get Access to the thrust reverser aft hinge fittings. Do a detailed inspection of the aft hinge fittings and the eight
attachment bolts for signs of damage. If any damage to the aft hinge fitting and/or attachment bolts is found,
the damage must be corrected before further flight and the preventive modification must be scheduled. For
Group 1, Configuration 2 airplanes, do a detailed inspection of washer stackup. If the stackup is incorrect, the
washers must be removed and reinstalled.
Preventive Modification:
Operators may do the preventive modification. After the preventive modification is accomplished it is no longer
necessary to do the repeat inspections shown in this service bulletin. Get Access to the thrust reverser aft hinge
fittings. Remove the thrust reverser C-ducts. Trim the aft hinge fitting lugs or install a fitting designed with the
trim already in it, to clear possible contact with the hinge beam. Remove the four attachment bolts on each aft
hinge fitting, high frequency eddy current (HFEC) inspect the fastener holes and replace with new and improved
bolts, washers and nuts. Refit thrust reversers and return airplane to a serviceable condition.
The related 757-300 bulletin is Service Bulletin 757-54-0050.
EFFECTIVITY
757-200/ 200CB/ 200PF airplanes with Rolls Royce RB211-535E engines. Refer to Paragraph 1.A.1.
COMPLIANCE
Refer to Service Bulletin Paragraph 1.E for compliance.
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2008-13-20 is related to this service
bulletin.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of October 17, 2003. Please refer to
Paragraph 2.B., Industry Support Information.
MANPOWER
Refer to Service Bulletin Paragraph 1.G Manpower.
MATERIAL INFORMATION
Boeing Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
8 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 9 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
-DO A DETAILED INSPECTION ON THE THRUST
REVERSER AFT HINGE FITTINGS AND ATTACH
BOLTS, AND HFEC THE ATTACH BOLT FASTENER
HOLES FOR DAMAGE.
-REPAIR OR MODIFY AFT HINGE FITTING IF
LEFT ENGINE SHOWN  DAMAGE IS FOUND.
RIGHT ENGINE SIMILAR
D37474
Original Issue: July 16, 2007
Revision 2: July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  • 9 of 78

### Page 10

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
10 of 78
BOEING SERVICE BULLETIN 757-54-0049
BLANK PAGE

### Page 11

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-54-0049
Original Issue: July 16, 2007
Revision 2: July 27, 2011
ATA System: 5451
SUBJECT: NACELLES/PYLONS - Nacelle Strut - Thrust Reverser Aft Hinge Fitting Modification
- Rolls Royce RB211-535E Engines
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624N001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below. Refer to PRR 54530-267RS and PRR
55029-R for data about this change.
DESCRIPTIONCONFIGURATIONGROUP
757-200/ 200CB/ 200PF Airplanes, with Rolls Royce RB211-535E
engines.
-1
Airplanes that have not been modified in accordance with the original
issue of this service bulletin.
1
Airplanes that have been modified in accordance with the original
issue of this service bulletin.
2
Airplane Models:
757-200, 757-200CB, 757-200PF
GroupVariable Number
1NA002 - NA028
1NA194 - NA199
1NA237 - NA239
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
11 of 78

### Page 12

GroupVariable Number
1NA301 - NA305
1NA341 - NA352
1NA392 - NA399
1NA401 - NA408
1NA441 - NA447
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
1NB201 - NB204
1NB221 - NB228
1NB230
1NB236
1NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311
1NB321 - NB331
1NB421 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB561
1NB571
1NB581 - NB583
1NC058 - NC062
1NC936 - NC950
1NC971 - NC974
1ND001 - ND007
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
12 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 13

GroupVariable Number
1ND011 - ND059
1ND111 - ND113
1ND161 - ND199
1ND201 - ND203
1ND221 - ND225
1ND241 - ND248
1ND301 - ND322
1ND401
1ND891
1ND895
1NJ001 - NJ004
1NJ031 - NJ032
1NN001 - NN002
1NN051 - NN052
1NS601 - NS616
1NT001 - NT009
1NT201 - NT202
1NT231 - NT234
1NT237 - NT240
1NT242
1NT245 - NT248
1NT281 - NT289
1NT381 - NT386
1NT401 - NT409
1NT411 - NT412
1NT426 - NT427
1NT431 - NT432
1NT436 - NT438
1NT446
1NT731 - NT769
1NT861 - NT862
1NT901 - NT916
1NT971 - NT985
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
13 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 14

2. Spares Affected
Examine your spares supply for the parts or components identified in Paragraph 2.C., Parts
Necessary for Each Airplane. If any parts or components are found, refer to Paragraph 2.C. for
the recommended use.
B. Concurrent Requirements
You cannot make the changes given in this service bulletin unless the changes given in Service Bulletin
757-54-0015 R3 are made prior to or concurrent with this service bulletin. The 757-54-0015 service
bulletin replaced an older aft hinge fitting and attachment bolts with the current part numbers on airplanes
line numbers through 241. The changes given in Service Bulletin 757-54-0015 were made on airplanes
after line number 241, before delivery.
C. Reason
This service bulletin gives instructions to do a detailed inspection and preventive modification on the
thrust reverser aft hinge fittings, and hinge fitting attachment bolts. Attachment bolts have been reported
to fail at the thrust reverser aft hinge fittings. The hinge has integral fail-safe features, but loss of the
entire four bolt pattern constitutes complete loss of the load path. Loss of the load path could result in
the departure of the thrust reverser from the airplane which could result in damage to the airplane and
hazards to persons or property on the ground.
Boeing has received 13 reports of 14 separate incidents of bolt failure at the thrust reverser aft hinge
fittings. All of the reported incidents occurred on airplanes with Rolls Royce RB211-535E engines. Of
the 14 incidents there were 9 hinges with 1 out of 4 bolts failed, 2 hinges with 2 out of 4 bolts failed,
and 3 hinges with 3 out of 4 bolts failed.
The possible causes of the bolt failure can be attributed to high operational loads, contact loads caused
by possible interference between the thrust reverser hinge and the hinge beam, and the 4 attachment
bolts are installed with washers that can ride the radius of the hinge fitting spotface.
As a part of a service bulletin validation program, this change was completed on airplane NT744 by
Service Bulletin 757-54-0049 Validation Copy 01 before the initial release of this service bulletin. The
change completed on airplane NT744 by Service Bulletin 757-54-0049 Validation Copy 01 is equivalent
to the initial release of this service bulletin.
Revision 1: This revision is sent to change the Work Instructions for Part III - Preventive Modification,
and the associated figures, to allow the option of doing the Part III - Preventive Modification on just the
hinges that are damaged, and allow continued repeat inspections on the hinges that are undamaged.
This revision also corrects the names of the different washers (special washer, countersunk washer,
plain washer) used in Figure 11 and Figure 12.
Revision 2: This revision is sent to inform operators that an aft hinge fitting designed with the trim
already in it, is being made available as an option to trimming an existing or new hinge fitting.
Changes appearing in Revision 1 of this service bulletin include:
— Paragraph 1.E., Compliance - Footnote and Damage Tolerance note added.
— Paragraph 3.B., Work Instructions, Part III-Preventive Modification - Added steps 4, 5. Added
Caution note to step 3.
— Figures 1-12 were modified to include a footnote adding flexibility in inspecting and modifying the
hinges.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
14 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 15

— Figures 13 and 14 were modified to include a flag note stating that quantities could be halved if
only one hinge is removed/installed on either strut.
— The Fastener Tables in Figures 11 and 12 were modified to correct the names of washers and to
add words that clarify the washer orientation.
— Added note to Figures 5, 6, 9 and 10, to clarify that you remove one bolt at a time, replace it with
a new bolt, and then go to the next bolt.
— Added a second configuration for those airplanes that have completed the original issue of this
service bulletin, to inspect for washer stackup in Figures 11 and 12. Added Appendix A to show
correct fastener stackup.
— Added flexibility to install a new aft hinge fitting if heat damage is found after trimming.
— Added ammonium persulfate in addition to Nital to use for inspecting for heat damage.
— Replaced BMS 3-24 grease with BMS 3-33 grease.
— Changed torque reference from SOPM 20-50-01 to BAC5009.
— Changed Figures 13 and 14 to interim installation of existing fittings and removed torque
specifications in footnotes.
Changes appearing in Revision 2 of this service bulletin include:
– Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added optional 311N5148-4
Hinge Fitting and optional replacement shim.
– Paragraph 3.A., General Information, updated the general notes.
– Paragraph 3.B., Work Instructions, Part II - Inspection, added optional 311N5148-4 fitting to step
1.a, 1.e.(2)(b), 2.a., and 2.e.(2)(b).
– Paragraph 3.B. Work Instructions, Part III - Preventive Modification, added option to use a new
311N5148-4 fitting designed with the trim already in it, under Step 4.b. Option 2, substeps (2) and
(5).
– Figures 13 and 14, added optional 311N5148-4 fitting to step 6, added footnote (c) with option to
use BMS 5-95 instead of BMS 5-45, and added footnote (d) with option to install a replacement
shim.
Boeing Service Related Problem (SRP) 757-SRP-54-0098 is related to this service bulletin.
D. Description
Inspections:
Get Access to the thrust reverser aft hinge fittings. Do a detailed inspection of the aft hinge fittings and
the eight attachment bolts for signs of damage. If any damage to the aft hinge fitting and/or attachment
bolts is found, the damage must be corrected before further flight and the preventive modification must
be scheduled. For Group 1, Configuration 2 airplanes, do a detailed inspection of washer stackup. If
the stackup is incorrect, the washers must be removed and reinstalled.
Preventive Modification:
Operators may do the preventive modification. After the preventive modification is accomplished it is
no longer necessary to do the repeat inspections shown in this service bulletin. Get Access to the thrust
reverser aft hinge fittings. Remove the thrust reverser C-ducts. Trim the aft hinge fitting lugs or install
a fitting designed with the trim already in it, to clear possible contact with the hinge beam. Remove the
four attachment bolts on each aft hinge fitting, high frequency eddy current (HFEC) inspect the fastener
holes and replace with new and improved bolts, washers and nuts. Refit thrust reversers and return
airplane to a serviceable condition.
The related 757-300 bulletin is Service Bulletin 757-54-0050.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
15 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 16

Revision 1: More work is necessary on airplanes changed as shown in the original issue of this service
bulletin. Washer stackup should be inspected for the correct installation sequence. If the installation is
found to be incorrect, the nut(s) and bolt(s) must be removed and the washers reinstalled.
Revision 2 : No more work is necessary on airplanes changed in accordance with Revision 1 of this
service bulletin.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
415, 416, 425, 426, 431, 441757-200, 757-200CB, 757-
200PF
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive FAA AD 2008-13-20 is related to this
service bulletin.
Table 1(Group 1, Configuration 1): Inspection of the two thrust reverser aft hinge fittings and eight fitting
attach bolts on each engine for contact and damage
Re-
peat
Inter-
val
(Not
to Ex-
ceed)
Compliance
Time
ActionCondition
3000
Flight
Cycles
(a)
Within 3000
Flight Cycles af-
ter the original
issue date of
this service bul-
letin
Do a Detailed Inspection of the two thrust reverser aft hinge
fittings and eight fitting attach bolts on each engine as
given in Accomplishment Instruction 3.B.,Part II
Group 1, Configuration
1 Airplanes
-Before Further
Flight
Replace the aft hinge fitting and do Preventive Modification
as given in Accomplishment Instruction 3.B., Part III (c)
Cracked or broken aft
hinge fitting
-Before Further
Flight
Apply surface finish as given in Accom-
plishment Instruction 3.B., Part II
Option 1Aft hinge fitting shows
contact damage less
than 0.005 inch depth -Within 3000
Flight Cycles af-
ter surface finish
is applied
Do Preventive Modification as given in
Accomplishment Instruction 3.B., Part
III (c)
-Before Further
Flight
Do Preventive Modification as given in
Accomplishment Instruction 3.B., Part
III (c)
Option 2
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
16 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 17

Table 1(Group 1, Configuration 1): Inspection of the two thrust reverser aft hinge fittings and eight fitting
attach bolts on each engine for contact and damage
Re-
peat
Inter-
val
(Not
to Ex-
ceed)
Compliance
Time
ActionCondition
-Before Further
Flight
Do Preventive Modification as given in Accomplishment
Instruction 3.B., Part III (c)
Aft hinge fitting shows
contact damage greater
than or equal to 0.005
inch depth
-Before Further
Flight
Do Preventive Modification as given in
Accomplishment Instruction 3.B., Part
III (c)
Option 1Damaged attach bolt
-Before Further
Flight
Do a High Frequency Eddy Current
(HFEC) Inspection of the attach bolt hole
as given in Accomplishment Instruction
3.B., Part II
Option 2
-Before Further
Flight
Replace bolt as given in Accomplishment Instruction 3.B.,
Part II
No crack was found in
attach bolt hole as a re-
sult of HFEC inspection -Within 3000
Flight Cycles af-
ter bolt replace-
ment
Do Preventive Modification as given in Accomplishment
Instruction 3.B., Part III (c)
-Before Further
Flight
Do Preventive Modification as given in Accomplishment
Instruction 3.B., Part III(c)
A crack was found in
attach bolt hole as a re-
sult of HFEC inspection
-Before Further
Flight
If any crack is found in aft hinge fitting, install new aft hinge
fitting or contact Boeing for repair instructions and repair
as given in Accomplishment Instruction 3.B., Part III
0.4688 inch nominal
lower fastener hole with
crack
OROR
If any crack is found in the strut, contact Boeing for repair
instructions and do the repair.
0.5312 inch nominal
upper fastener hole
with crack
-Before Further
Flight
Install new aft hinge fitting as given in Accomplishment
Instruction 3.B., Part III.
Aft hinge fitting is found
to have heat damage
after trimming. OR
Contact Boeing for repair instructions and do the repair.
(a) Accomplishment of the Preventive Modification on a hinge as given in Accomplishment Instruction 3.B.,
Part III terminates the requirement to do repeat inspections on that hinge.
(b) Not Used
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
17 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 18

Table 1(Group 1, Configuration 1): Inspection of the two thrust reverser aft hinge fittings and eight fitting
attach bolts on each engine for contact and damage
Re-
peat
Inter-
val
(Not
to Ex-
ceed)
Compliance
Time
ActionCondition
(c) Preventive Modification is required for hinges with damage and is optional for hinges without damage.
Repeat inspections are required on all unmodified hinges until the Preventive Modification, as given in Ac-
complishment Instruction 3.B, Part III, is accomplished.
Table 2 (Group 1, Configuration 2): DETAILED INSPECTION OF FASTENER STACKUP ON AFT
HINGE FITTINGS FOR AIRPLANES THAT HAVE BEEN MODIFIED IN ACCORDANCE WITH THE
ORIGINAL ISSUE OF THIS SERVICE BULLETIN
Repeat Interval (Not
to Exceed)
Compliance TimeActionCondition
-Within 3000 flight cy-
cles after the Revision
1 date of this Service
Bulletin.
Do a one-time detailed
inspection of fastener
stackup as given in Ac-
complishment Instruc-
tion 3.B., Part IV.
Group 1, Configuration
2 airplanes
-Before Further FlightReinstall washers cor-
rectly as given in Ac-
complishment Instruc-
tion 3.B., Part IV.
Washers found to be
installed incorrectly af-
ter doing one-time de-
tailed inspection.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
This service bulletin has been approved by the FAA. In addition, the Manager of the FAA Seattle Aircraft
Certification Office (ACO) approves the accomplishment of the applicable inspections, investigative
and corrective actions with the corresponding compliance times specified in Tables 1 and 2 under
paragraph 1.E., "Compliance," of Service Bulletin 757-54-0049, Revision 2, as an AMOC to the
accomplishment of the applicable inspections, investigative and corrective actions with the corresponding
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
18 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 19

compliance times specified in paragraph 1.E., "Compliance," of Service Bulletin 757-54-0049, dated
July 16, 2007, as required by paragraphs (f) and (h) of AD 2008-13-20. When this service bulletin
specifies contacting Boeing for repair instruction, the repair instructions must be approved by the FAA
in accordance with paragraph (k) of the AD. All provisions of AD 2008-13-20 that are not specifically
referenced in this paragraph remain fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task-hours necessary to do this for each airplane. This
estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task-hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1 Configuration 1 - INSPECTION MANHOURS:
Elapsed HoursTask-HoursNumber of Per-
sons
Task
1.02.02Open Access
0.51.02Figure 1
0.51.02Figure 2
1.02.02Close Access
3.06.0TOTAL FOR EACH AIRPLANE
Group 1 Configuration 1 - MODIFICATION MANHOURS:
Elapsed HoursTask-HoursNumber of Per-
sons
Task
5.2510.52Open Access
4.08.02Figure 3
4.08.02Figure 4
2.55.02Figure 5
2.55.02Figure 6
0.51.02Figure 7
0.51.02Figure 8
2.55.02Figure 9
2.55.02Figure 10
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
19 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 20

Elapsed HoursTask-HoursNumber of Per-
sons
Task
0.51.02Figure 11
0.51.02Figure 12
5.2510.52Close Access
30.561TOTAL FOR EACH AIRPLANE
NOTE: The total man-hours is dependant on the method of modification. The total man-hours shown
are for modification of the aft hinge fitting on the airplane.
Group 1, Configuration 2 - DETAILED INSPECTION (of Fastener Stackup) MANHOURS:
Elapsed HoursTask-HoursNumber of PersonsTask
1.02.02Open Access
1.02.02Inspect
1.02.02Close Access
3.06.0TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR-54530-267RS and PRR-55029-R.
b. 757 Aircraft Maintenance Manual (AMM) 24-41-01, 29-11-25, 71-00-02, 78-31-00, 78-31-10,
78-31-20.
c. 757 Non-destructive Testing (NDT) Manual, Part 6, 51-00-16, Part 6, 51-00-17.
d. Boeing Drawing 65-88700.
e. Boeing Tooling Drawing MIT012N8549-2.
f. Service Bulletin 757-54-0015 "NACELLES/PYLONS - NACELLE STRUT - THRUST
REVERSER HINGE FITTING REPLACEMENT".
g. Service Bulletin 757-54-0050 "NACELLES/PYLONS - Nacelle Strut - Thrust Reverser Hinge
Fitting Modification - Rolls Royce RB211-535E Engines".
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
20 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 21

h. Standard Overhaul Practices Manual (SOPM) 20-10-01, 20-10-02, 20-10-03, 20-30-03,
20-42-10, 20-44-01, 20-50-01, 20-50-10, 20-50-19
i. Boeing Service Letter 757-SL-51-022
j. Federal Aviation Administration (FAA) Airworthiness Directive 2008-13-20
2. Data supplied with this Service Bulletin:
a. Drawings:
ADCNDCN/REVSheetTitleDrawing No
--1Miscelaneous Tool - Hinge Assembly
Aligning Tool
MIT012N8549-2
--1
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
54-51757 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.C., Parts Necessary For Each Airplane, for interchangeability and intermixability
information.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
21 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 22

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
22 of 78
BOEING SERVICE BULLETIN 757-54-0049
BLANK PAGE

### Page 23

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary For Each Airplane, and Paragraph
2.D., Parts Necessary to Change Spares, as shown below. If there is a limit to the quantity (QTY) of
available kits, a supply sequence is given by Spares. More kits become available as shown in the
Reorder Lead Time (ROLT). ROLT is calculated from the date Boeing gets the purchase order.
Unit Price thru
Oct/31/06
ROLT
(Weeks)
QTYDateNameKit Number
$5,276301008/25/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
$5,276301009/01/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
$5,276301009/09/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
$5,276301009/16/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
$5,276301009/23/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
$5,276301009/30/05TOP KIT-THRUST RE-
VERSER HINGE MODI-
FICATION RB211-535E
012N5108-1
The kits/parts are subject to the terms and conditions of the Boeing standard purchase order
acknowledgment. After the Unit Price date, new price and ROLT data is applicable. Prices are in United
States dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of the methods that
follow:
1. Order on-line via ATA Spec 2000 or Boeing Part Page
2. Fax to (206) 662-7145
3. Spares Customer Support - MC 36-65 Boeing Spares Department P.O. Box 3707 Seattle,
Washington 98124-2207 USA
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
23 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 24

B. Industry Support Information
Boeing warranty remedies are available for 757 airplanes in warranty as of October 17, 2003. For the
initial inspection labor hour reimbursement for airplanes in warranty as of that date, send a claim to
Boeing Warranty. Please note that subsequent inspections, as outlined in the MPD (Maintenance
Planning Document), do not qualify for Boeing warranty remedies. If the condition described in this
service bulletin is found during the initial, or MPD directed inspection, please note that the kits for
airplanes in warranty as of October 17, 2003, will be supplied at no charge. Send a purchase order for
the kits to Boeing Spares, and a warranty claim for labor hours to Boeing Commercial Airplanes Group
- Warranty & Product Assurance Contracts. Please refer to this service bulletin number and reference
the airplane variable numbers in your purchase order and any labor hour claim.
C. Parts Necessary For Each Airplane
1. Kits/Parts:
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator, are necessary for each airplane.
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
Kit 012N5108
NotesExisting Part
Number
NameQTYNew Part Number
-1
-TOP KIT- THRUST REVERSER HINGE
MODIFICATION RB211-535E
-012N5108-1
(b)(d)-WASHER- SPECIAL8012N5108-2
(b)(d)-WASHER- SPECIAL8012N5108-3
(b)(d)-WASHER- SPECIAL8012N5108-4
(b)(d)-WASHER- SPECIAL8012N5108-5
(a)(b)(c)(d)(e)BACB30LE7U( )BOLT, 12 PT HEAD8BACB30US7K15X
(a)(b)(c)(d)(e)BACB30LE7U( )
BACB30LE7U( )X
BACB30LE7U( )Y
BOLT, 12 PT HEAD8BACB30US7K15Y
(a)(b)(c)(d)(e)BACB30LE8U19BOLT, 12 PT HEAD8BACB30US8K19X
(a)(b)(c)(d)(e)BACB30LE8U19
BACB30LE8U19X
BACB30LE8U19Y
BOLT, 12 PT HEAD8BACB30US8K19Y
(a)(c)BACN10HR7CSSELF-LOCKING NUT8BACN10HR7CS
(a)(c)BACN10HR8CSNUT8BACN10HR8CS
(a)(b)(c)BACW10BP7APUWASHER, PLAIN8BACW10BP71APU
(a)(b)(c)BACW10BP7APUWASHER, PLAIN8BACW10BP72APU
(a)(b)(c)BACW10BP8APUWASHER, PLAIN8BACW10BP81ACU
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
24 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 25

Kit 012N5108
NotesExisting Part
Number
NameQTYNew Part Number
-1
(a)(b)(c)BACW10BP8APUWASHER, PLAIN8BACW10BP82ACU
(a) Discard the existing part.
(b) This part is not used in production.
(c) You cannot use the existing part to replace the new or changed part.
(d) There are more parts than are necessary.
(e) If grip length shown is not available at Boeing, fasteners supplied in kits may be one grip length longer
than indicated. Also, if any fasteners part numbers listed are not available or have been superseded,
substitute fasteners may be supplied in kits. Boeing Document D-590 and Boeing Drawing 65-88700,
are used to determine the part numbers used as substitutes.
2. Parts and Materials Supplied by the Operator:
NotesNameQTYPart Number / Specification
(a)De-Soto Hi-Temperature Primer4 OuncesType 51
(b)Grease4 OuncesBMS 3-33
(f)Sealant-BMS 5-45 or BMS 5-95
(f)Primer-BMS 10-11, Type 1
(c) (d)Hinge Fitting-311N5148-1
(c) (d)Hinge Fitting-311N5148-4
(e)Shim-Stock 0.125 x 3.0 x 4.0 2024-T3
aluminum sheet
(a) Refer to the Boeing Standard Overhaul Practices Manual SOPM 20-44-01 or 757 Structural Repair
Manual, Chapter 51, for material sources.
(b) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for supplier data.
(c) Hinge Fitting quantity depends on the number of fittings that need to be replaced.
(d) 311N5148-4, aft hinge fitting designed with the trim already in it, is optional to 311N5148-1 aft hinge
fitting.
(e) Optional solid shim made to the same dimensions as the existing laminated shim, if removed. Quantity
as required.
(f) Primer applied to optional solid shim. After primer dries, fay surface sealant applied to shim. Quantity
of both primer and sealant as required.
3. Parts Modified and Reidentified:
The parts shown below are changed as shown in this service bulletin. The quantity (QTY) is the
number of parts changed on each airplane.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
25 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 26

NotesNew Part NumberNameQTYExisting Part Number
(a) (c) (d)(b)Hinge Fitting4311N5148-1
(a) Make the change given in this service bulletin.
(b) There is no equivalent Boeing part number for the changed part. Identify on the part that the change
given in this service bulletin was made.
(c) You cannot use the existing part to replace the modified part. If you use the existing part to replace
the modified part you will cancel the effect of the change given in this service bulletin.
(d) 311N5148-4 fitting, which is designed with the trim already in it, is interchangeable with a trimmed
311N5148-1 fitting.
4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
However, MIT012N8549-2 may be necessary if the aft hinge fitting is being replaced.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
26 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 27

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in 757 SRM Chapter 51
4. Use the approved fastener and process material substitutions as given in 757 SRM
Chapter 51. Alternate fasteners are listed in 757 SRM Chapter 51 and Boeing Drawing
65-88700.
5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
6. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
7. If the length of any fastener specified in this service bulletin does not meet installation
standards given in 757 SRM Chapter 51, then a fastener of the same specification,
or an approved substitute, with a length which meets the installation standards given
in 757 SRM Chapter 51 may be used. In addition, washers may be installed for
fastener grip length as given in 757 SRM Chapter 51.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
27 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 28

9. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
10. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "as
given in" are included in the instruction, the procedure in the Boeing document must
be used.
11. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
12. Refer to Appendix A for Aft Hinge Fitting Fastener Stackup.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
The removed part can be discarded if a new or serviceable part is installed.
16. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
17. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
28 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 29

B. WORK INSTRUCTIONS
PART I - ACCESS
1. Remove electrical power and electrically ground airplane. Refer to 757 AMM 24-41-01 as an
accepted procedure.
2. Install thrust reverser lock out pins. Refer to 757 AMM 78-31-00 as an accepted procedure.
3. Open thrust reverser C-Ducts. Refer to 757 AMM 78-31-00 as an accepted procedure.
4. Install thrust reverser actuator hold open locks, tool number B71009. Refer to 757 AMM 71-00-02
as an accepted procedure.
PART II - INSPECTION (Group 1, Configuration 1)
1. Do a Detailed Inspection on the number 1 engine thrust reverser aft hinge fittings and attach bolts
as given in Figure 1.
a. If the aft hinge fitting is cracked or broken, do PART III - Preventive modification and install a
new 311N5148-1 or a new 311N5148-4 fitting.
NOTE: The new aft hinge fitting can be positioned using tool MIT012N8549-2. See Service
Bulletin 757-54-0015 for more information on how to use the tool.
b. If no damage to aft hinge fittings and attach bolts is found, do one of the following:
(1) Do PART V - Close Access, and do repeat inspections as given in Paragraph 1.E.
Compliance until the preventive modification is accomplished.
(2) Do PART III - Preventive Modification.
c. If contact damage to the base metal of the thrust reverser aft hinge fittings is less than 0.005
inch deep, do one of the following options:
(1) Option 1: Reapply surface finish, Type 51 Primer, as given in SOPM 20-44-01, and do
Part III - Preventive Modification as given in Paragraph 1.E Compliance.
(2) Option 2: Do PART III - Preventive Modification.
d. If contact damage to the base metal of the thrust reverser aft hinge fittings is found to be equal
to or more than 0.005 inches deep, do PART III - Preventive Modification.
e. If damage to an attach bolt is found, do one of the following options:
(1) Option 1: Do PART III - Preventive Modification.
(2) Option 2: Remove the damaged attach bolt and HFEC inspect the attach bolt hole as
given in 757 NDT, Part 6, 51-00-17 and 757 NDT, Part 6, 51-00-16.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
29 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 30

(a) If no crack exists install new attach bolt (either existing BACB30LE or new
BACB30US) and do PART III - Preventive Modification as given in Paragraph 1.E
Compliance.
(b) If a crack is found do PART III - Preventive Modification and install a new 311N5148-1
or a new 311N5148-4 fitting.
2. Do a Detailed Inspection on the number 2 engine thrust reverser aft hinge fittings and attach bolts
as given in Figure 2.
a. If the aft hinge fitting is cracked or broken, do PART III - Preventive modification and install a
new 311N5148-1 or a new 311N5148-4 fitting.
NOTE: The new aft hinge fitting can be positioned using tool MIT012N8549-2. See Service
Bulletin 757-54-0015 for more information on how to use the tool.
b. If no damage to aft hinge fittings and attach bolts is found, do one of the following:
(1) Do PART V - Close Access, and do repeat inspections as given in Paragraph 1.E.
Compliance until the preventive modification is accomplished.
(2) Do PART III - Preventive Modification.
c. If contact damage to the base metal of the thrust reverser aft hinge fittings is less than 0.005
inch deep, do one of the following options:
(1) Option 1: Reapply surface finish, Type 51 Primer, as given in SOPM 20-44-01, and do
Part III - Preventive Modification as given in Paragraph 1.E Compliance.
(2) Option 2: Do PART III - Preventive Modification.
d. If contact damage to the base metal of the thrust reverser aft hinge fittings is found to be equal
to or more than 0.005 inches deep, do PART III - Preventive Modification.
e. If damage to an attach bolt is found, do one of the following options:
(1) Option 1: Do PART III - Preventive Modification.
(2) Option 2: Remove the damaged attach bolt and HFEC inspect the attach bolt hole as
given in 757 NDT, Part 6, 51-00-17 and 757 NDT, Part 6, 51-00-16.
(a) If no crack exists install new attach bolt (either existing BACB30LE or new
BACB30US) and do PART III - Preventive Modification as given in Paragraph 1.E
Compliance.
(b) If a crack is found do PART III - Preventive Modification and install a new 311N5148-1
or a new 311N5148-4 fitting.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
30 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 31

PART III - PREVENTIVE MODIFICATION (Group 1, Configuration 1)
1. Remove hydraulic power and depressurize hydraulic systems. Refer to 757 AMM 29-11-25 as an
accepted procedure.
2. Remove the C-Duct hinged access door. Refer to 757 AMM 78-31-10 as an accepted procedure.
CAUTION: THE THRUST REVERSER C-DUCTS SHOULD BE REMOVED. IF THE THRUST
REVERSER C-DUCTS ARE NOT REMOVED AND YOU DO THE PREVENTIVE
MODIFICATION, THEN HYDROGEN EMBRITTLEMENT CAN OCCUR AFTER THE
PLATING IS APPLIED TO THE AFT HINGES.
3. Remove thrust reverser C-Ducts. Refer to 757 AMM 78-31-20 as an accepted procedure.
4. Aft Hinge Fittings that are damaged and/or have damaged bolts, must do one of the options below.
Any fittings that are undamaged with undamaged bolts, and are not being re-worked per the options
below, must continue to be inspected at the times shown in Paragraph 1.E Compliance, until steps
4 and 5 are accomplished.
NOTE: Option 2 below applies to NEW and EXISTING fittings. The aft hinge fitting can be
positioned during installation using tool MIT012N8549-2. MIT012N8549-2 is used in
Service Bulletin 757-54-0015. Step 5 of this part may be performed prior to or concurrently
with step 4 of this part.
a. Option 1:
(1) Trim the thrust reverser aft hinge fittings, 311N5148-1, on the number 1 engine as given
in Figure 3.
(2) Trim the thrust reverser aft hinge fittings, 311N5148-1, on the number 2 engine as given
in Figure 4.
b. Option 2:
(1) Remove the thrust reverser aft hinge fittings on the number 1 engine as given in Figure
13.
(2) Trim the thrust reverser aft hinge fittings, 311N5148-1, on the number 1 engine as given
in Figure 3, or use a new 311N5148-4 fitting, which is designed with the trim already in
it.
(3) Install the thrust reverser aft hinge fittings on the number 1 engine as given in Figure 13.
(4) Remove the thrust reverser aft hinge fittings on the number 2 engine as given in Figure
14.
(5) Trim the thrust reverser aft hinge fittings, 311N5148-1, on the number 2 engine as given
in Figure 4, or use a new 311N5148-4 fitting, which is designed with the trim already in
it.
(6) Install the thrust reverser aft hinge fittings on the number 2 engine as given in Figure 14.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
31 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 32

5. A trimmed fitting or a fitting designed with the trim already in it, must have larger bolts, new washers,
and new nuts installed. Do the steps below which apply to a trimmed fitting or a fitting designed
with the trim already in it.
a. Oversize and High Frequency Eddy Current (HFEC) Inspect the thrust reverser aft hinge fitting
lower fastener holes on the number 1 engine as given in Figure 5.
(1) If any crack is found in the aft hinge fitting and the fastener hole size is already 0.4688
inch nominal, then install a new aft hinge fitting or contact Boeing for repair instructions
and repair the fitting.
(2) If any crack is found in the strut structure and the fastener hole size is already 0.4688
inch nominal, then contact Boeing for repair instructions and do the repair.
b. Oversize and HFEC Inspect the thrust reverser aft hinge fitting lower fastener holes on the
number 2 engine as given in Figure 6.
(1) If any crack is found in the aft hinge fitting and the fastener hole size is already 0.4688
inch nominal, then install a new aft hinge fitting or contact Boeing for repair instructions
and repair the fitting.
(2) If any crack is found in the strut structure and the fastener hole size is already 0.4688
inch nominal, then contact Boeing for repair instructions and do the repair.
c. Install the lower fasteners in the thrust reverser aft hinge fitting on the number 1 engine as
given in Figure 7.
d. Install the lower fasteners in the thrust reverser aft hinge fitting on the number 2 engine as
given in Figure 8.
e. Oversize and HFEC Inspect the thrust reverser aft hinge fitting upper fastener holes on the
number 1 engine as given in Figure 9.
(1) If any crack is found in the aft hinge fitting and the fastener hole size is already 0.5312
inch nominal, then install a new aft hinge fitting or contact Boeing for repair instructions
and repair the fitting.
(2) If any crack is found in the strut structure and the fastener hole size is already 0.5312
inch nominal, then contact Boeing for repair instructions and do the repair.
f. Oversize and HFEC Inspect the thrust reverser aft hinge fitting upper fastener holes on the
number 2 engine as given in Figure 10.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
32 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 33

(1) If any crack is found in the aft hinge fitting and the fastener hole size is already 0.5312
inch nominal, then install a new aft hinge fitting or contact Boeing for repair instructions
and repair the fitting.
(2) If any crack is found in the strut structure and the fastener hole size is already 0.5312
inch nominal, then contact Boeing for repair instructions and do the repair.
g. Install the upper fasteners in the thrust reverser aft hinge fitting on the number 1 engine as
given in Figure 11.
h. Install the upper fasteners in the thrust reverser aft hinge fitting on the number 2 engine as
given in Figure 12.
6. Install thrust reverser C-Ducts. Refer to 757 AMM 78-31-20 as an accepted procedure.
7. Install the C-Duct hinged access door. Refer to 757 AMM 78-31-10 as an accepted procedure.
PART IV - ONE-TIME DETAILED INSPECTION FOR AIRPLANES THAT HAVE DONE THE ORIGINAL
ISSUE OF THIS SERVICE BULLETIN (Group 1, Configuration 2)
1. Do a One-Time Detailed Inspection of the washers installed under the nuts and bolts that are
installed in FIGURE 11 and FIGURE 12 to secure the aft hinge fittings to the structure. The
countersunk washer must be installed under the head of the bolt with the countersink towards the
bolt head and the special washer must be installed under the nut with the tapered side toward the
aft hinge fitting. See Appendix A.
2. If the washers are not installed correctly, then remove the nut and bolt and reinstall the hardware
as given in FIGURE 11 and FIGURE 12.
PART V - CLOSE ACCESS
1. Remove thrust reverser actuator hold open lock tool number B71009. Refer to 757 AMM 71-00-02
as an accepted procedure.
2. Close and lock thrust reversers. Refer to 757 AMM 78-31-00 as an accepted procedure.
3. Remove thrust reverser lock out pins. Refer to 757 AMM 78-31-00 as an accepted procedure.
4. Return Airplane to a serviceable condition.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2: July 27, 2011
33 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 34 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
SEE A
FWDC
• B
• B
→ FWD  D37480
FIGURE 1: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  34 of 78

### Page 35 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
A-A
TYPICAL
(3 LOCATIONS)
B-B
TYPICAL  1893221
(3 LOCATIONS)
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
FIGURE 1: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 2 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  35 of 78

### Page 36

MORE DATA (d)PROCEDURENAMETASKSTEP
(a) (b)Detailed InspectionBoltsInspect1
(c)Detailed InspectionAft Hinge FittingInspect2
(a) (b)Detailed InspectionBoltsInspect3
(c)Detailed InspectionAft Hinge FittingInspect4
Inspect the bolts for damage. Look for loose, fretting or broken bolts.(a)
Removal of the bolts is not required for this inspection.(b)
Inspect the aft hinge fitting for signs of contact and any broken or cracked fitting.(c)
If only one hinge is being inspected, it is OK to skip the steps that don't apply.(d)
FIGURE 1: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
36 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 37 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
_ SEE A
• A
(A  FWD<
• B
B  →FWD  D37478
FIGURE 2: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  37 of 78

### Page 38 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
A-A
TYPICAL
(3 LOCATIONS)
B-B
TYPICAL  1893224
(3 LOCATIONS)
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
FIGURE 2: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 2 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  38 of 78

### Page 39

MORE DATA (d)PROCEDURENAMETASKSTEP
(a) (b)Detailed InspectionBoltsInspect1
(c)Detailed InspectionAft Hinge FittingInspect2
(a) (b)Detailed InspectionBoltsInspect3
(c)Detailed InspectionAft Hinge FittingInspect4
Inspect the bolts for damage. Look for loose, fretting or broken bolts.(a)
Removal of the bolts is not required for this inspection.(b)
Inspect the aft hinge fitting for signs of contact and any broken or cracked fitting.(c)
If only one hinge is being inspected, it is OK to skip the steps that don't apply.(d)
FIGURE 2: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - DETAILED INSPECTION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
39 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 40 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE B
SEE
FWD<
TRIM LINE
1-10 R
0.90
• - 10
0.90
0.301
' 0.101
1.747
1.547
0.10
A-A
TYPICAL  D37483
(3 LOCATIONS)
FIGURE 3: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 1 OF 4)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  40 of 78

### Page 41 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
• B
• B  → FWD
TRIM LINE
1.10 R
0.90
1.10 R
0.90
0.301
0.101
1.747
1.547
0.10
B-B
TYPICAL  D37479
(3 LOCATIONS)
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
FIGURE 3: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 2 OF 4)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  41 0f 78

### Page 42

MORE DATA (h)QTYIDENTIFICATIONNAMETASKSTEP
(a)1Thrust Reverser
Aft Hinge Fitting
Clean1
(b)3Trim LocationsIdentify2
Refer to SOPM 20-10-01
and SOPM 20-10-02 as
an accepted procedure.
(e) (f) (c)
3Thrust Reverser
Aft Hinge Fitting
Lug
Hand Blend3
(g)3Thrust Reverser
Aft Hinge Fitting
Deburr4
(d)3Thrust Reverser
Aft Hinge Fitting
Inspect5
Refer to SOPM 20-10-03
as an accepted proce-
dure. Intensity 0.014A,
coverage 2.0
Shot Peen or Flap
Peen
Do6
Refer to SOPM 20-42-10
an accepted procedure.
Cadmium Plate to a
thickness 0.0003 - 0.0005
inch.
Cadmium PlateApply7
Refer to SOPM 20-44-01
as an accepted proce-
dure.
1 CoatType 51PrimerApply8
(a)1Thrust Reverser
Aft Hinge Fitting
Clean9
(b)3Trim LocationsIdentify10
Refer to SOPM 20-10-01
and SOPM 20-10-02 as
an accepted procedure.
(e) (f) (c)
3Thrust Reverser
Aft Hinge Fitting
Lug
Hand Blend11
(g)3Thrust Reverser
Aft Hinge Fitting
Deburr12
(d)3Thrust Reverser
Aft Hinge Fitting
Inspect13
Refer to SOPM 20-10-03
as an accepted proce-
dure. Intensity 0.014A,
coverage 2.0
Shot Peen or Flap
Peen
Do14
FIGURE 3: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 3 OF 4)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
42 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 43

MORE DATA (h)QTYIDENTIFICATIONNAMETASKSTEP
Refer to SOPM 20-42-10
as an accepted proce-
dure. Cadmium Plate to
a thickness 0.0003 -
0.0005 inch.
Cadmium PlateApply15
Refer to SOPM 20-44-01
as an accepted proce-
dure.
1 CoatType 51PrimerApply16
Clean the hinge. Refer to SOPM 20-30-03 as an accepted procedure.(a)
Mark the trim locations. Refer to SOPM 20-50-10 as an accepted procedure.(b)
Restore the surface finish to 125 micro-inches Ra.(c)
Do a detailed inspection of the trimmed area for signs of heat damage using Nital or Ammonium
Persulfate as given in SOPM 20-10-02. If any damage is found, install a new aft hinge fitting or
contact Boeing for additional repair instructions.
(d)
Boeing recommends the use of a carbide rotary file. The part should be ground in stages,
checking between stages, checking for heating after each stage. The part surface shall remain
cool to the touch.
(e)
Rotary burrs and files in portable hand-held motors may be used if the speed is limited to 500
rpm, maximum. Higher speed settings and/or other tools may be used provided that:
(f)
— The operator shall produce no discoloration.
— The operator shall not cause sparking or release of molten fines.
— The tools shall be applied with pressure and contact time such that no heat damage occurs.
— Verify the higher speed settings and/or other tools by in-process inspection of test samples
or test parts. Refer to SOPM 20-10-02 as an accepted procedure.
Break all sharp edges, the minimum/maximum radius requirement (0.02 - 0.06 radius).(g)
If only one hinge is being trimmed, it is OK to skip the steps that don't apply.(h)
FIGURE 3: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 4 OF 4)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
43 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 44 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
→A
SEE C
SEE A
FWD<
TRIM LINE
1-10 R
0.90
0.301
/ 0.101
1.747
1.547
0.10
A-A
TYPICAL  D37484
(3 LOCATIONS)
FIGURE 4: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 1 OF 4)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  44 0t 78

### Page 45 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
• B
• B  → FWD
TRIM LINE
1.10 R
0.90
1.10 R
0.90
0.301
0.101
1.747
1.547
0.10
B-B
TYPICAL
(3 LOCATIONS)
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
FIGURE 4: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 2 OF 4)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  BOEING PROPRIETARY -  757-54-0049
Copyright © Unpublished Work - See page 1 for details.  45 0f 78

### Page 46

MORE DATA (h)QTYIDENTIFICATIONNAMETASKSTEP
(a)1Thrust Reverser
Aft Hinge Fitting
Clean1
(b)3Trim LocationsIdentify2
Refer to SOPM 20-10-01
and SOPM 20-10-02 as
an accepted procedure.
(e) (f) (c)
3Thrust Reverser
Aft Hinge Fitting
Lug
Hand Blend3
(g)3Thrust Reverser
Aft Hinge Fitting
Deburr4
(d)3Thrust Reverser
Aft Hinge Fitting
Inspect5
Refer to SOPM 20-10-03
as an accepted proce-
dure. Intensity 0.014A,
coverage 2.0
Shot Peen or Flap
Peen
Do6
Refer to SOPM 20-42-10
an accepted procedure.
Cadmium Plate to a
thickness 0.0003 - 0.0005
inch.
Cadmium PlateApply7
Refer to SOPM 20-44-01
as an accepted proce-
dure.
1 CoatType 51PrimerApply8
(a)1Thrust Reverser
Aft Hinge Fitting
Clean9
(b)3Trim LocationsIdentify10
Refer to SOPM 20-10-01
and SOPM 20-10-02 as
an accepted procedure.
(e) (f) (c)
3Thrust Reverser
Aft Hinge Fitting
Lug
Hand Blend11
(g)3Thrust Reverser
Aft Hinge Fitting
Deburr12
(d)3Thrust Reverser
Aft Hinge Fitting
Inspect13
Refer to SOPM 20-10-03
as an accepted proce-
dure. Intensity 0.014A,
coverage 2.0
Shot Peen or Flap
Peen
Do14
FIGURE 4: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 3 OF 4)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
46 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 47

MORE DATA (h)QTYIDENTIFICATIONNAMETASKSTEP
Refer to SOPM 20-42-10
as an accepted proce-
dure. Cadmium Plate to
a thickness 0.0003 -
0.0005 inch.
Cadmium PlateApply15
Refer to SOPM 20-44-01
as an accepted proce-
dure.
1 CoatType 51PrimerApply16
Clean the hinge. Refer to SOPM 20-30-03 as an accepted procedure.(a)
Mark the trim locations. Refer to SOPM 20-50-10 as an accepted procedure.(b)
Restore the surface finish to 125 micro-inches Ra.(c)
Do a detailed inspection of the trimmed area for signs of heat damage using Nital or Ammonium
Persulfate as given in SOPM 20-10-02. If any damage is found, install a new aft hinge fitting or
contact Boeing for additional repair instructions.
(d)
Boeing recommends the use of a carbide rotary file. The part should be ground in stages,
checking between stages, checking for heating after each stage. The part surface shall remain
cool to the touch.
(e)
Rotary burrs and files in portable hand-held motors may be used if the speed is limited to 500
rpm, maximum. Higher speed settings and/or other tools may be used provided that:
(f)
— The operator shall produce no discoloration.
— The operator shall not cause sparking or release of molten fines.
— The tools shall be applied with pressure and contact time such that no heat damage occurs.
— Verify the higher speed settings and/or other tools by in-process inspection of test samples
or test parts. Refer to SOPM 20-10-02 as an accepted procedure.
Break all sharp edges, the minimum/maximum radius requirement (0.02 - 0.06 radius).(g)
If only one hinge is being trimmed, it is OK to skip the steps that don't apply.(h)
FIGURE 4: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING - TRIM
(SHEET 4 OF 4)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
47 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 48 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
- SEE (A
FWDS
5X6  →→FWD
FIGURE 5: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  48 of 78

### Page 49

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
MORE DATA (f)QTYIDENTIFICATIONNAMETASKSTEP
2BACN10HR7CSNutRemove1
(a)(g)2BACB30LE7U( )Bolt
BACB30LE7U( )X
BACB30LE7U( )Y
2BACW10BP7ACUWasher
2BACW10BP7APUWasher
Oversize the hole to the size
listed in table 1 below. (e)
2Fastener HoleDrill/Ream2
As given in 757 NDT, Part 6,
51-00-17 and757 NDT, Part
6, 51-00-16 (b)
2High Frequency Eddy
Current (HFEC)
Open HoleInspect3
2BACN10HR7CSNutRemove4
(a)(g)2BACB30LE7U( )Bolt
BACB30LE7U( )X
BACB30LE7U( )Y
2BACW10BP7ACUWasher
2BACW10BP7APUWasher
Oversize the hole to the size
listed in table 1 below. (e)
2Fastener HoleDrill/Ream5
As given in 757 NDT, Part 6,
51-00-17 and757 NDT, Part
6, 51-00-16 (c)
2High Frequency Eddy
Current (HFEC)
Open HoleInspect6
BACB30LE7U( ) was installed in production. BACB30LE7U( )X and BACB30LE7U( )Y may
have been installed as given in SB 757-54-0015.
(a)
If any crack is found repeat steps 2 and 3.(b)
If any crack is found repeat steps 5 and 6.(c)
Not Used(d)
The hole through the hinge fitting may be up to 0.457 inch diameter from production. This
condition is equivalent to a 0.4526 - 0.4536 inch existing hole diameter.
(e)
If only one hinge is being oversized and inspected, it is OK to skip the steps that don't apply.(f)
Remove one bolt at a time when oversizing and inspecting.(g)
FIGURE 5: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
49 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 50

Table 1 Fastener Hole Sizes
New Hole DiameterExisting Hole Diameter
0.4526 - 0.4536 inchNominal
0.4683 - 0.4693 inch0.4526 - 0.4536 inch
Do Not Oversize Hole0.4683 - 0.4693 inch
FIGURE 5: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
50 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 51 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
_ SEE (A
FWDS
56  —FWD  D37487
FIGURE 6: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  51 of 78

### Page 52

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
MORE DATA (f)QTYIDENTIFICATIONNAMETASKSTEP
2BACN10HR7CSNutRemove1
(a)(g)2BACB30LE7U( )Bolt
BACB30LE7U( )X
BACB30LE7U( )Y
2BACW10BP7ACUWasher
2BACW10BP7APUWasher
Oversize the hole to the size
listed in table 1 below. (e)
2Fastener HoleDrill/Ream2
As given in 757 NDT, Part 6,
51-00-17 and 757 NDT, Part 6,
51-00-16 (b)
2High Frequency Eddy
Current (HFEC)
Open HoleInspect3
2BACN10HR7CSNutRemove4
(a)(g)2BACB30LE7U( )Bolt
BACB30LE7U( )X
BACB30LE7U( )Y
2BACW10BP7ACUWasher
2BACW10BP7APUWasher
Oversize the hole to the size
listed in table 1 below. (e)
2Fastener HoleDrill/Ream5
As given in 757 NDT, Part 6,
51-00-17 and 757 NDT, Part 6,
51-00-16 (c)
2High Frequency Eddy
Current (HFEC)
Open HoleInspect6
BACB30LE7U( ) was installed in production. BACB30LE7U( )X and BACB30LE7U( )Y may
have been installed as given in SB 757-54-0015.
(a)
If any crack is found repeat steps 2 and 3.(b)
If any crack is found repeat steps 5 and 6.(c)
Not Used(d)
The hole through the hinge fitting may be up to 0.457 inch diameter from production. This
condition is equivalent to a 0.4526 - 0.4536 inch existing hole diameter.
(e)
If only one hinge is being oversized and inspected, it is OK to skip the steps that don't apply.(f)
Remove one bolt at a time when oversizing and inspecting.(g)
FIGURE 6: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
52 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 53

Table 1 Fastener Hole Sizes
New Hole DiameterExisting Hole Diameter
0.4526 - 0.4536 inchNominal
0.4683 - 0.4693 inch0.4526 - 0.4536 inch
Do Not Oversize Hole0.4683 - 0.4693 inch
FIGURE 6: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
53 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 54 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
- SEE A
AN  FWDS
3 AIN  → FWD  D37488
FIGURE 7: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  54 of 78

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
MORE DATA (d)QTYIDENTIFICATIONNAMETASKSTEP
See fastener table
and Appendix A (a)
(b) (c)
2-FastenersInstall (New)1
See fastener table
and Appendix A (a)
(b) (c)
2-FastenersInstall (New)2
Torque the fasteners. Refer to BAC5009 as an accepted procedure. Torque bolt head. Torque
to 427-453 in-lbs (target 440 in-lbs).
(a)
Apply BMS3-33 grease to the threads.(b)
Apply type 51 high temperature primer to bolt shank only. Refer to SOPM 20-44-01 as an ac-
cepted procedure.
(c)
If only one hinge is being worked, it is OK to skip the step that doesn't apply.(d)
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener.
If the grip length shown is not available at Boeing, fasteners supplied in kits may be one grip length longer than
indicated. Also, if any of the fastener part numbers are not available or have been superseded, substitute
fasteners may be supplied in Boeing kits, Boeing Document D-590 and Boeing drawing 65-88700 are used to
determine the part numbers used as substitutes.
FIGURE 7: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
55 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 56

MORE DATAHOLE DIAIDENTIFICATIONNAMECODE
Install special washer under the
head of the bolt with countersink
towards bolt head and install the
plain washer under the nut. See
Appendix A.
0.4531 inchBACN10HR7CSNutA
BACB30US7K15XBolt
BACW10BP71APUPlain Washer
012N5108-2Special
Washer
Install special washer under the
head of the bolt with countersink
towards bolt head and install the
plain washer under the nut. See
Appendix A.
0.4688 inchBACN10HR7CSNutA
BACB30US7K15YBolt
BACW10BP72APUPlain Washer
012N5108-4Special
Washer
FIGURE 7: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
56 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 57 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
_ SEE (A)
O AN  FWD<
→FWD
FIGURE 8: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  57 of 78

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one engine.
MORE DATA (d)QTYIDENTIFICATIONNAMETASKSTEP
See fastener table
and Appendix A (a)
(b) (c)
2-FastenersInstall (New)1
See fastener table
and Appendix A (a)
(b) (c)
2-FastenersInstall (New)2
Torque the fasteners. Refer to BAC5009 as an accepted procedure. Torque bolt head. Torque
to 427-453 in-lbs (target 440 in-lbs).
(a)
Apply BMS3-33 grease to the threads.(b)
Apply type 51 high temperature primer to bolt shank only. Refer to SOPM 20-44-01 as an ac-
cepted procedure.
(c)
If only one hinge is being worked, it is OK to skip the step that doesn't apply.(d)
The codes shown below agree with the letter shown in the upper left corner of the fastener symbols in the figure.
A number in the lower right corner gives the grip length of the fastener.
If the grip length shown is not available at Boeing, fasteners supplied in kits may be one grip length longer than
indicated. Also, if any of the fastener part numbers are not available or have been superseded, substitute
fasteners may be supplied in Boeing kits, Boeing Document D-590 and Boeing drawing 65-88700 are used to
determine the part numbers used as substitutes.
FIGURE 8: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
58 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 59

MORE DATAHOLE DIAQTYIDENTIFICATIONNAMECODE
Install special washer under the
head of the bolt with countersink
towards bolt head and install the
plain washer under the nut. See
Appendix A.
0.4531 inch4BACN10HR7CSNutA
4BACB30US7K15XBolt
4BACW10BP71APUPlain Washer
4012N5108-2Special
Washer
Install special washer under the
head of the bolt with countersink
towards bolt head and install the
plain washer under the nut. See
Appendix A.
0.4688 inch4BACN10HR7CSNutA
4BACB30US7K15YBolt
4BACW10BP72APUPlain Washer
4012N5108-4Special
Washer
FIGURE 8: ENGINE NUMBER 2 - THRUST REVERSER AFT HINGE FITTING LOWER FASTENER HOLES
- FASTENER INSTALLATION
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: July 16, 2007
757-54-0049Revision 2 July 27, 2011
59 of 78
BOEING SERVICE BULLETIN 757-54-0049

### Page 60 (OCR)

BOEING SERVICE BULLETIN 757-54-0049
This Figure applies only to: Group 1, Configuration 1.
SEE
_ SEE A
FWDE
—FWD
FIGURE 9: ENGINE NUMBER 1 - THRUST REVERSER AFT HINGE FITTING UPPER FASTENER HOLES
- OVERSIZE AND HIGH FREQUENCY EDDY CURRENT INSPECTION
(SHEET 1 OF 3)
Original Issue: July 16, 2007
Revision 2 July 27, 2011  757-54-0049
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  60 of 78

The text continues at https://openairdocs.org/service-documents/boeing/sb-757-54-0049/file/99a88085a6ca.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
