# Boeing Special Attention Service Bulletin 757-57-0068: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0547; AD 2013-03-20 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 757-57-0068](https://openairdocs.org/service-documents/boeing/sb-757-57-0068.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin - SB-757-57-0068-01
- Pages: 54
- PDF: https://openairdocs.org/files/sha256/8d/c2/8dc2b24f7850a547090ee971e018b985580562aa87ce66a273f2f17df42aeee1
- Page: https://openairdocs.org/service-documents/boeing/sb-757-57-0068/file/8dc2b24f7850

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-57-0068
Original Issue: September 15, 2009
Revision 1: July 19, 2011
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Detailed Inspection of Inboard
and Outboard Slats Main Track Downstop Assembly and Slat Track Housing
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2009 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
1 of 54
3.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
2 of 54
BOEING SERVICE BULLETIN 757-57-0068
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 5
C. Reason ................................................ 1 5
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 2 0
G. Manpower .............................................. 2 0
H. Weight and Balance Changes .................................... 2 1
I. Electrical Load Data ......................................... 2 1
J. References .............................................. 2 1
1. Existing Data .......................................... 2 1
2. Data supplied with this Service Bulletin ............................ 2 2
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 2 2
K. Publications Affected ........................................ 2 2
L. Interchangeability and Intermixability of Parts ........................... 2 2
2. MATERIAL INFORMATION ........................................ 2 3
A. Material - Price and Availability ................................... 2 3
B. Industry Support Information .................................... 2 3
C. Parts Necessary For Each Airplane ................................. 2 3
1. Kits/Parts ............................................ 2 3
2. Parts and Materials Supplied by the Operator ........................ 2 3
3. Parts Modified and Reidentified ................................ 2 3
4. Parts Removed and Not Replaced .............................. 2 3
D. Parts Necessary to Change Spares ................................. 2 3
E. Special Tooling - Price and Availability ............................... 2 3
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 4
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 5
A. GENERAL INFORMATION ..................................... 2 5
B. WORK INSTRUCTIONS ....................................... 2 6
FIGURE 1: LEFT WING - SLAT NUMBERS 1, 2, 3 AND 4 - DETAILED INSPECTION OF MAIN TRACK
DOWNSTOP ASSEMBLIES .................................. 3 1
FIGURE 2: LEFT WING - SLAT NUMBER 5 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES ......................................... 3 3
FIGURE 3: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - DETAILED INSPECTION OF MAIN TRACK
DOWNSTOP ASSEMBLIES .................................. 3 5
FIGURE 4: RIGHT WING - SLAT NUMBER 6 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES ......................................... 3 7
FIGURE 5: LEFT WING - SLAT NUMBER 1, 2, 3, 4 AND 5 - DETAILED INSPECTION OF SLAT TRACK
HOUSING ............................................ 3 9
FIGURE 6: RIGHT WING - SLAT NUMBER 6, 7, 8, 9 AND 10 - DETAILED INSPECTION OF SLAT TRACK
HOUSING ............................................ 4 1
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
3 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 4

FIGURE 7: LEFT WING - SLAT NUMBER 1, 2, 3 AND 4 - MAIN TRACK DOWNSTOP ASSEMBLY NUT -
TORQUE APPLICATION ................................... 4 3
FIGURE 8: LEFT WING - SLAT NUMBER 5 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION ......................................... 4 5
FIGURE 9: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - MAIN TRACK DOWNSTOP ASSEMBLY
NUT - TORQUE APPLICATION ................................ 4 7
FIGURE 10: RIGHT WING - SLAT NUMBER 6 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION ......................................... 4 9
FIGURE 11: WINGS - SLAT NUMBERS 1 - 10 SLAT TRACK HOUSING - REPAIR ........... 5 1
APPENDIX A: INSPECTION RESULTS REPORT .............................. 5 3
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
4 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 5

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 757-57-0068Original Issue: September 15, 2009
Revision 1: July 19, 2011
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Detailed Inspection of Inboard
and Outboard Slats Main Track Downstop Assembly and Slat Track Housing
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on the airplane(s) changed in accordance with the original issue of this service
bulletin.
REASON FOR REVISION
This revision is sent to clarify downstop assembly components, damage condition limits for the slat track housing,
and torquing requirements for downstop fasteners. In addition, the part numbers were deleted from the inspection
tables, and the option to replace a slat can instead of repairing it was added.
These sections were changed:
1. Paragraph 1.E., Compliance, Tables 5 and 6, changed damage condition limits for the slat track housing
in the last row of the tables to less than 0.040 inches. Added option to replace the slat track housing if
damage was found and the remaining thickness was 0.040 inches or greater. Added requirement to replace
the slat track housing if a crack was found.
2. Paragraph 3.A., General Information, updated the general notes.
3. Paragraph 3.B.1.a., added option to reactivate the slats to reposition them. Paragraph 3.B.1.c., added option
to position the slat track to gain access to the downstop assembly. Paragraph 3.B.1.h.(2) and 3.B.1.m.(2),
added option to replace the slat track housing. Paragraph 3.B.1.h.(3) and 3.B.1.m.(3), added requirement
to replace the slat track housing if a crack is found during the detailed inspection. Paragraph 3.B.1.n and
3.B.2.e., added option to lubricate the slats before reinstalling the access panels. Paragraph 3.B.1.p., moved
Appendix completion conditions to Part 3.
4. Figures 1 and 3, removed part numbers and footnotes d through e.
5. Figures 2 and 4, updated parts shown in exploded view in illustration. Removed part numbers and footnotes
d through f.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
5 of 54

### Page 6

6. Figures 8 and 10, updated parts shown in exploded view in illustration. Added inspection step for the size
of the nut. Removed part number and specified diameter for each torque step. Reworded footnote b to
distinguish from size 4 and size 6 hardware. Removed footnote d. Also added Warning Note regarding
torquing the fasteners.
7. Figures 7 and 9, removed part number for torque step and footnote b.
8. Figure 11, removed "x" from illustration view B. Removed minimum distance between damage occurrences
from view B. Removed detail view A-A.
9. Appendix A, changed remaining thickness in last column to be less than 0.040 inches.
The data given in Information Notices 757-57-0068 IN02 and IN04 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
September 15, 2009Original Issue:
July 19, 2011Revision 1:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
6 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 7

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 757-57-0068Original Issue: September 15, 2009
Revision 1: July 19, 2011
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Detailed Inspection of Inboard
and Outboard Slats Main Track Downstop Assembly and Slat Track Housing
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
This Service Bulletin gives instruction to do a detailed inspection of the inboard and outboard main track downstop
assemblies of slat numbers 2 thru 9 and the inboard main track downstop assembly of slat numbers 1 and 10.
Instruction is also given to do a detailed inspection of all slat track housings for foreign object debris or visible
damage. An incorrectly installed main track downstop assembly can allow the main track downstop hardware
to fall off the slat track and into the slat track housing which could cause a puncture in the slat track housing
when the slat is retracted. A punctured slat track housing could result in a fuel leak and an increased risk of a
fire.
There have been two reports of a fuel leak from the front spar of the wing through the slat track housing. In at
least one case, the source of the fuel leak was from a puncture of the slat track housing that was caused by a
roller that had fallen into the slat track housing. It was determined that the roller was not a component of the slat
installation or the slat track support rib. The roller was subsequently driven into the slat track housing by the
retracting slat track. In both cases, there were no reports of a fire as a result of the fuel leak.
Boeing Service Related Problem (SRP) 757-SRP-57-0210 is related to this service bulletin.
ACTION
Do a detailed inspection of the inboard and outboard main track downstop assemblies of slat numbers 2 thru 9
and the inboard main track downstop assembly of slat numbers 1 and 10 to make sure that each main track
downstop assembly is correctly installed and has no damaged or missing parts. Apply torque to the main track
downstop assembly nut to make sure it has been correctly installed. Do a detailed inspection of all slat track
housings for foreign object debris and damage to the wall of the slat track housing.
If a main track downstop assembly is incorrectly installed, remove and correctly reinstall the main track downstop
assembly. If a main track downstop assembly has a damaged or missing part, then replace the main track
downstop assembly part. If foreign object debris is found in the housing assembly of the slat track, remove all
foreign object debris from the area. If visible damage in the slat track housing is found, repair the damage or
replace the slat track housing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
7 of 54

### Page 8

EFFECTIVITY
All 757 Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, repair, reinstallation and torque measurement
given in this service bulletin.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
13.9019.40All
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
8 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 9 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
DO A DETAILED INSPECTION OF
THE LEADING EDGE MAIN TRACK
DOWNSTOP ASSEMBLIES OF
SLATS NUMBER 2 THROUGH 9
AND THE INBOARD TRACK
DOWNSTOP ASSEMBLIES OF
SLATS NUMBER 1 AND 10 FOR
CORRECT INSTALLATION AND
DAMAGED PARTS
SLAT
DO A DETAILED INSPECTION
OF THE SLAT TRACK
APPLY TORQUE TO THE  HOUSING FOR ANY FOREIGN
MAIN  TRACK  MAIN TRACK DOWNSTOP  ASSEMBLY NUT TO MAKE  OBJECT DEBRIS AND  DAMAGE TO THE WALL OF
SURE IT HAS BEEN  THE SLAT TRACK HOUSING.
CORRECTLY INSTALLED
A-A
FWD
TYPICAL SLAT TRACK AND
SLAT TRACK HOUSING  1579165
Original Issue: September 15, 2009
Revision 1: July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  9 of 54

### Page 10

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
10 of 54
BOEING SERVICE BULLETIN 757-57-0068
BLANK PAGE

### Page 11

Commercial 
Airplanes
757
Service Bulletin
SPECIAL ATTENTION
Number: 757-57-0068
Original Issue: September 15, 2009
Revision 1: July 19, 2011
ATA System: 5740
SUBJECT: WINGS - Leading Edge and Leading Edge Devices - Detailed Inspection of Inboard
and Outboard Slats Main Track Downstop Assembly and Slat Track Housing
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
DESCRIPTIONCONFIGURATIONGROUP
All 757 Airplanes-1
Airplane Models:
757-200, 757-200CB, 757-200PF, 757-300
GroupVariable Number
1NA001 - NA028
1NA191 - NA199
1NA201 - NA239
1NA301 - NA305
1NA341 - NA352
1NA391 - NA399
1NA401 - NA408
1NA441 - NA447
1NA501 - NA586
1NB001 - NB004
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
11 of 54

### Page 12

GroupVariable Number
1NB021 - NB023
1NB036 - NB041
1NB051 - NB053
1NB061 - NB073
1NB079
1NB131 - NB148
1NB161 - NB162
1NB166 - NB168
1NB201 - NB204
1NB221 - NB228
1NB230
1NB236
1NB239
1NB261 - NB267
1NB291 - NB299
1NB301 - NB302
1NB311 - NB312
1NB321 - NB331
1NB421 - NB438
1NB446
1NB451 - NB454
1NB501 - NB523
1NB561
1NB571
1NB581 - NB583
1NC001 - NC033
1NC041 - NC042
1NC051 - NC052
1NC056 - NC062
1NC066 - NC084
1NC091 - NC094
1NC151
1NC161
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
12 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 13

GroupVariable Number
1NC901 - NC951
1NC971 - NC974
1ND001 - ND007
1ND011 - ND059
1ND111 - ND113
1ND161 - ND199
1ND201 - ND203
1ND221 - ND225
1ND241 - ND248
1ND301 - ND322
1ND401
1ND891
1ND895
1NE001 - NE008
1NE011 - NE088
1NE091 - NE094
1NE141 - NE150
1NE161 - NE177
1NE201 - NE204
1NE301 - NE302
1NE311 - NE325
1NJ001 - NJ004
1NJ031 - NJ032
1NJ551 - NJ555
1NL001 - NL002
1NL006 - NL017
1NL101 - NL109
1NL141
1NL601 - NL616
1NN001 - NN002
1NN051 - NN052
1NP901 - NP904
1NS601 - NS616
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
13 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 14

GroupVariable Number
1NT001 - NT009
1NT201 - NT202
1NT231 - NT234
1NT237 - NT240
1NT242
1NT245 - NT248
1NT281 - NT289
1NT341 - NT347
1NT351 - NT360
1NT371 - NT373
1NT375 - NT379
1NT381 - NT386
1NT401 - NT409
1NT411 - NT412
1NT426 - NT427
1NT431 - NT432
1NT436 - NT438
1NT441 - NT442
1NT446
1NT701 - NT769
1NT791 - NT796
1NT861 - NT862
1NT881 - NT885
1NT901 - NT916
1NT971 - NT985
1NU031 - NU038
1NU701 - NU705
1NU721 - NU728
1NU731 - NU732
2. Spares Affected
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
14 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 15

B. Concurrent Requirements
None.
C. Reason
This Service Bulletin gives instruction to do a detailed inspection of the inboard and outboard main
track downstop assemblies of slat numbers 2 thru 9 and the inboard main track downstop assembly
of slat numbers 1 and 10. Instruction is also given to do a detailed inspection of all slat track housings
for foreign object debris or visible damage. An incorrectly installed main track downstop assembly can
allow the main track downstop hardware to fall off the slat track and into the slat track housing which
could cause a puncture in the slat track housing when the slat is retracted. A punctured slat track
housing could result in a fuel leak and an increased risk of a fire.
There have been two reports of a fuel leak from the front spar of the wing through the slat track housing.
In at least one case, the source of the fuel leak was from a puncture of the slat track housing that was
caused by a roller that had fallen into the slat track housing. It was determined that the roller was not
a component of the slat installation or the slat track support rib. The roller was subsequently driven
into the slat track housing by the retracting slat track. In both cases, there were no reports of a fire as
a result of the fuel leak.
Revision 1: This revision is sent to clarify downstop assembly components, damage condition limits
for the slat track housing, and torquing requirements for downstop fasteners. In addition, the part
numbers were deleted from the inspection tables, and the option to replace a slat can instead of repairing
it was added.
The data given in Information Notices 757-57-0068 IN02 and IN04 is included in this revision.
Boeing Service Related Problem (SRP) 757-SRP-57-0210 is related to this service bulletin.
D. Description
Do a detailed inspection of the inboard and outboard main track downstop assemblies of slat numbers
2 thru 9 and the inboard main track downstop assembly of slat numbers 1 and 10 to make sure that
each main track downstop assembly is correctly installed and has no damaged or missing parts. Apply
torque to the main track downstop assembly nut to make sure it has been correctly installed. Do a
detailed inspection of all slat track housings for foreign object debris and damage to the wall of the slat
track housing.
If main track downstop assembly is incorrectly installed, remove and correctly reinstall the main track
downstop assembly. If the main track downstop assembly has a damaged or missing part, then replace
the main track downstop assembly part. If foreign object debris is found in the housing assembly of
the slat track, remove all foreign object debris from the area. If visible damage in the slat track housing
is found, repair the damage or replace the slat track housing.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
512, 522, 523, 524, 525, 612, 622, 623, 624, 625757-200, 757-200CB, 757-
200PF, 757-300
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
15 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 16

E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Table 1: Left wing - Slat Numbers 1, 2, 3 and 4 - Detailed Inspection of Main Track Downstop
Assemblies
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the inboard and outboard
main track downstop as-
semblies of slat numbers
2, 3, 4 and the inboard
main track downstop as-
sembly of slat number 1 in
accordance with Accom-
plishment Instructions
3.B.1.d.
All airplanes
Before further flightRemove and correctly rein-
stall main track downstop
assembly in accordance
with Accomplishment In-
structions 3.B.1.d.(1)
Main track downstop
assembly order is in-
correct
Before further flightReplace main track down-
stop assembly part in ac-
cordance with Accomplish-
ment Instructions
3.B.1.d.(2)
Main track downstop
assembly part is
missing or damaged
Within 24 months after the date on this
service bulletin
Apply torque to the inboard
and outboard main track
downstop assembly nut of
slat numbers 2, 3, 4 and
the inboard main track
downstop assembly nut of
slat number 1 in accor-
dance with Accomplish-
ment Instructions 3.B.1.e.
All airplanes
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
16 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 17

Table 2: Left Wing - Slat Number 5 - Detailed Inspection of Main Track Downstop Assemblies
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the inboard and outboard
main track downstop as-
semblies of slat number 5
in accordance with Accom-
plishment Instructions
3.B.1.f.
All airplanes
Before further flightRemove and correctly rein-
stall main track downstop
assembly in accordance
with Accomplishment In-
structions 3.B.1.f.(1)
Main track downstop
assembly order is in-
correct
Before further flightReplace main track down-
stop assembly part in ac-
cordance with Accomplish-
ment Instructions
3.B.1.f.(2)
Main track downstop
assembly part is
missing or damaged
Within 24 months after the date on this
service bulletin
Apply torque to the inboard
and outboard main track
downstop assembly nut of
slat number 5 in accor-
dance with Accomplish-
ment Instructions 3.B.1.g.
All airplanes
Table 3: Right Wing - Slat Numbers 7, 8, 9 and 10 - Detailed Inspection of Main Track Downstop
Assemblies
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the inboard and outboard
main track downstop as-
semblies of slat numbers
7, 8, 9 and the inboard
main track downstop as-
sembly of slat number 10
in accordance with Accom-
plishment Instructions
3.B.1.i.
All airplanes
Before further flightRemove and correctly rein-
stall main track downstop
assembly in accordance
with Accomplishment In-
structions 3.B.1.i.(1)
Main track downstop
assembly order is in-
correct
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
17 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 18

Table 3: Right Wing - Slat Numbers 7, 8, 9 and 10 - Detailed Inspection of Main Track Downstop
Assemblies
Compliance TimeActionCondition
Before further flightReplace main track down-
stop assembly part in ac-
cordance with Accomplish-
ment Instructions
3.B.1.i.(2)
Main track downstop
assembly part is
missing or damaged
Within 24 months after the date on this
service bulletin
Apply torque to the in
board and outboard main
track downstop assembly
nut of slat numbers 7, 8, 9
and the inboard main track
downstop assembly nut of
slat number 10 in accor-
dance with Accomplish-
ment Instructions 3.B.1.j.
All airplanes
Table 4: Right Wing - Slat Number 6 - Detailed Inspection Of Main Track Downstop Assemblies
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the inboard and outboard
main track downstop as-
semblies of slat number 6
in accordance with Accom-
plishment Instructions
3.B.1.k.
All airplanes
Before further flightRemove and correctly rein-
stall main track downstop
assembly in accordance
with Accomplishment In-
structions 3.B.1.k.(1)
Main track downstop
assembly order is in-
correct
Before further flightReplace main track down-
stop assembly part in ac-
cordance with Accomplish-
ment Instructions
3.B.1.k.(2)
Main track downstop
assembly part is
missing or damaged
Within 24 months after the date on this
service bulletin
Apply torque to the main
track downstop assembly
nut of slat number 6 in ac-
cordance with Accomplish-
ment Instructions 3.B.1.l.
All airplanes
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
18 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 19

Table 5: Left Wing - Slat Numbers 1, 2, 3, 4 and 5 - Detailed Inspection of Slat Track Housing
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the slat track housings of
slat numbers 1, 2, 3, 4 and
5 in accordance with Ac-
complishment Instructions
3.B.1.h.
All airplanes
Before further flightRemove foreign object de-
bris in accordance with
Accomplishment Instruc-
tions 3.B.1.h.(1)
Foreign object debris
found in the slat track
housing
Before further flightRepair the slat track hous-
ing in accordance with Ac-
complishment Instructions
3.B.1.h.(2)
Damage found in the
slat track housing that
results in a remaining
thickness of 0.040
inches or greater OR
Replace the slat track
housing in accordance with
Accomplishment Instruc-
tions 3.B.1.h.(2)
Before further flightReplace slat track housing
or contact Boeing for repair
instructions in accordance
with Accomplishment In-
structions 3.B.1.h.(3)
Damage found in the
slat track housing that
results in a remaining
thickness less than
0.040 inches or if a
crack was found
Table 6: Right Wing - Slat Number 6, 7, 8, 9 and 10 - Detailed Inspection of Slat Track Housing
Compliance TimeActionCondition
Within 24 months after the date on this
service bulletin
Do a detailed inspection of
the slat track housings of
slat numbers 6, 7, 8, 9 and
10 in accordance with Ac-
complishment Instructions
3.B.1.m.
All airplanes
Before further flightRemove foreign object de-
bris in accordance with
Accomplishment Instruc-
tions 3.B.1.m.(1)
Foreign object debris
found in the slat track
housing
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
19 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 20

Table 6: Right Wing - Slat Number 6, 7, 8, 9 and 10 - Detailed Inspection of Slat Track Housing
Compliance TimeActionCondition
Before further flightRepair the slat track hous-
ing in accordance with Ac-
complishment Instructions
3.B.1.m.(2)
Damage found in the
slat track housing that
results in a remaining
thickness of 0.040
inches or greater OR
Replace the slat track
housing in accordance with
Accomplishment Instruc-
tions 3.B.1.m.(2)
Before further flightReplace slat track housing
or contact Boeing for repair
instructions in accordance
with Accomplishment In-
structions 3.B.1.m.(3)
Damage found in the
slat track housing that
results in a remaining
thickness less than
0.040 inches or if a
crack was found
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
20 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 21

Elapsed HoursTask HoursNumber of Per-
sons
Task
2.755.502Deactivate Slats
and Open Access
1.751.751FIGURE 1
0.750.751FIGURE 2
1.751.751FIGURE 3
0.750.751FIGURE 4
1.101.101FIGURE 5
1.101.101FIGURE 6
0.500.501FIGURE 7
0.100.101FIGURE 8
0.500.501FIGURE 9
0.100.101FIGURE 10
1.50 (a)1.50 (a)1FIGURE 11
2.755.502Close Access and
Activate Slats
13.9019.40TOTAL FOR EACH AIRPLANE
(a) Time estimates is for each slat track housing that requires repair and is not
included in the totals given.
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. Service Related Problem (SRP) 757-SRP-57-0210
b. Boeing Service Letter 757-SL-51-022
c. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-41-02, 20-43-03
d. Standard Wiring Practices Manual (SWPM) 20-10-11, 20-10-12, 20-10-12, 20-10-19
e. 757 Aircraft Maintenance Manual (AMM) 06-44-00, 12-21-08, 27-81-00, 27-81-10, 27-81-12,
27-81-18, 57-41-01
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
21 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 22

2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Slat No. 5 and No. 6 Installation - Inboard Leading Edge114N3001
Slat No. 5 and No. 6 Installation - Inboard Leading Edge (Rework)114N3047
Leading Edge Slat Installation - Outboard Wing114N4001
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
K. Publications Affected
Chapter-SectionPublication
27-81, 30-11, 57-41757 Maintenance Manual
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
22 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 23

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are not available for the inspection, repair, reinstallation and torque
measurement given in this service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number / Specifica-
tion
(a) (b)Chemical Conversion
Coating
-Alodine 600
(a) (c)Primer-BMS 10-20 TYPE II
(a) Only required if damage to the slat track housing is removed in accordance with this service
bulletin.
(b) Refer to SOPM 20-43-03 for material sources.
(c) See Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
23 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 24

F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
24 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 25

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
4. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
5. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
6. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
7. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
8. A Detailed Inspection is defined as: An intensive examination of a specific item,
installation, or assembly to detect damage, failure, or irregularity. Available lighting
is normally supplemented with a direct source of good lighting at an intensity deemed
appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may be
necessary. Surface cleaning and elaborate procedures may be required.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
25 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 26

9. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
10. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
11. Boeing Service Letter 757-SL-51-022, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
12. Refer to Appendix A for Inspection Results Report.
13. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
14. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
15. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
The removed part can be discarded if a new or serviceable part is installed.
16. This service bulletin includes functional test procedures for the systems changed by
this service bulletin. More functional tests can possibly be necessary in accordance
with standard maintenance practices because of interruption to other airplane systems.
17. Some Boeing parts are supplied in a temporary configuration. Those parts are
identified with a 'U', 'W', or 'Y' in place of the '-' (dash) in the part number. It is
permitted to install parts identified with a 'U', 'W', or 'Y' as an alternative to the '-'
(dash) part number. Boeing Drawing 005W0900 contains more data.
B. WORK INSTRUCTIONS
1. Part 1 - Main Track Downstop Assembly and Slat Track Housing - Inspection.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
26 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 27

a. Deactivate the leading edge slats. Refer to 757 AMM 27-81-00 as an accepted procedure.
You may have to reactivate the leading edge slats later to reposition them.
b. Remove access panels on the lower surface of the wing leading edge to get access to the
inboard and outboard main tracks of slat numbers 2, 3, 4, 5, 6, 7, 8, 9 and the inboard track
of slat number 1 and 10. Refer to 757 AMM 06-44-00 and 757 AMM 57-41-01 as accepted
procedures.
c. Position the slat track, if necessary, to gain access to the main track downstop assembly.
d. Do a detailed inspection for correct assembly order and missing or damaged parts of the
inboard and outboard main track downstop assemblies of slat numbers 2, 3, 4 and inboard
main track downstop assembly of slat number 1 in accordance with FIGURE 1.
(1) If the main track downstop assembly order is incorrect, then remove the main track
downstop assembly and reinstall the parts in the correct order. Refer to 757 AMM 27-81-12
as an accepted procedure.
NOTE: Figure 1 shows the downstop assembly bolt head pointing inboard in the
assembly sequence. However a reverse sequence with the downstop assembly
bolt head pointing outboard is acceptable.
(2) If main track downstop assembly part is missing or damaged, replace the part. Refer to
757 AMM 27-81-12 as an accepted procedure.
NOTE: A relative motion check can be used to confirm the presence of the bushing in
the slat track. If the downstop cannot be moved more than 0.010 inch relative
to the slat track in a vertical direction, then a visual inspection to confirm the
presence of the bushing is not required. If the downstop can be moved 0.010
inch relative to the slat track in a vertical direction, then the downstop assembly
must be visually inspected to confirm the presence of the bushing.
e. Apply torque to the inboard and outboard main track downstop assembly nut of slat numbers
2, 3, 4 and the inboard main track downstop assembly nut of slat number 1 in accordance
with FIGURE 7.
f. Do a detailed inspection for correct assembly order and missing or damaged parts of the
inboard and outboard main track downstop assemblies of slat number 5 in accordance with
FIGURE 2.
(1) If main track downstop assembly order is incorrect, then remove the main track downstop
assembly and reinstall the parts in the correct order. Refer to 757 AMM 27-81-10 as an
accepted procedure.
NOTE: Figure 2 shows the downstop assembly bolt head pointing inboard in the
assembly sequence. However a reverse sequence with the downstop assembly
bolt head pointing outboard is acceptable.
(2) If main track downstop assembly part is missing or damaged, replace the part. Refer to
757 AMM 27-81-10 as an accepted procedure.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
27 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 28

NOTE: A relative motion check can be used to confirm the presence of the bushing or
washer in the slat track. If the downstop assembly bolt cannot be moved more
than 0.010 inch relative to the slat track, then a visual inspection to confirm the
presence of the bushing is not required. If the downstop can be moved 0.010
inch relative to the slat track, then the downstop assembly must be visually
inspected to confirm the presence of the bushing or washer.
g. Apply torque to the inboard and outboard main track downstop assembly nut of slat number
5 in accordance with FIGURE 8.
h. Do a detailed inspection of the interior (dry side) of the slat track housing of slat numbers 1,
2, 3, 4 and 5 in accordance with FIGURE 5.
(1) If foreign object debris is found, remove it.
(2) If a slat track housing is damaged and the damage results in a remaining thickness of
0.040 inches or greater, do Part 2 - Slat Track Housing Repair, or replace the slat track
housing.
(3) If a slat track housing is damaged and the damage results in a remaining thickness less
than 0.040 inches or if a crack was found, replace the slat track housing or contact Boeing
for repair instructions and do the repair.
i. Do a detailed inspection for correct assembly order and missing or damaged parts of the
inboard and outboard main track downstop assemblies of slat numbers 7, 8, 9 and the inboard
main track downstop assembly of slat number 10 in accordance with FIGURE 3.
(1) If main track downstop assembly order is incorrect, then remove the main track downstop
assembly and reinstall the parts in the correct order. Refer to 757 AMM 27-81-12 as an
accepted procedure.
NOTE: Figure 3 shows the downstop assembly bolt head pointing inboard in the
assembly sequence. However a reverse sequence with the downstop assembly
bolt head pointing outboard is acceptable.
(2) If main track downstop assembly part is missing or damaged, replace the part. Refer to
757 AMM 27-81-12 as an acceptable procedure.
NOTE: A relative motion check can be used to confirm the presence of the bushing in
the slat track. If the downstop cannot be moved more than 0.010 inch relative
to the slat track in a vertical direction, then a visual inspection to confirm the
presence of the bushing is not required. If the downstop can be moved 0.010
inch relative to the slat track in a vertical direction, then the downstop assembly
must be visually inspected to confirm the presence of the bushing.
j. Apply torque to the inboard and outboard main track downstop assembly nut of slat numbers
7, 8, 9 and the inboard main track downstop assembly nut of slat number 10 in accordance
with FIGURE 9
k. Do a detailed inspection for correct assembly order and missing or damaged parts of the
inboard and outboard main track downstop assemblies of slat number 6 in accordance with
FIGURE 4.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
28 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 29

(1) If main track downstop assembly order is not correct, then remove the main track downstop
assembly and reinstall the parts in the correct order. Refer to 757 AMM 27-81-10 as an
accepted procedure.
NOTE: Figure 4 shows the downstop assembly bolt head pointing inboard in the
assembly sequence. However a reverse sequence with the downstop assembly
bolt head pointing outboard is acceptable.
(2) If main track downstop assembly part is missing or damaged, replace the part. Refer to
757 AMM 27-81-10 as an accepted procedure.
NOTE: A relative motion check can be used to confirm the presence of the bushing or
washer in the slat track. If the downstop cannot be moved more than 0.010 inch
relative to the slat track in any direction, then a visual inspection to confirm the
presence of the bushing is not required. If the downstop can be moved 0.010
inch relative to the slat track in any direction, then the downstop assembly must
be visually inspected to confirm the presence of the bushing or washer.
l. Apply torque to the inboard and outboard downstop assembly nut of slat number 6 in
accordance with FIGURE 10.
m. Do a detailed inspection of the interior (dry side) of the slat track housing of slat numbers 6,
7, 8, 9 and 10 in accordance with FIGURE 6.
(1) If foreign object debris is found, remove it.
(2) If a slat track housing is damaged and the damage results in a remaining thickness of
0.040 inches or greater, do Part 2 - Slat Track Housing Repair, or replace the slat track
housing.
(3) If a slat track housing is damaged and the damage results in a remaining thickness less
than 0.040 inches or if a crack was found, replace the slat track housing or contact Boeing
for repair information and do the repair.
n. It is optional to lubricate the slats, if necessary. Refer to 757 AMM 12-21-08 as an accepted
procedure.
o. Install access panels that were removed. Refer to 757 AMM 57-41-01 as an accepted
procedure.
p. Put the Slats back into its usual condition. Refer to 757 AMM 27-81-00 as an accepted
procedure.
q. Put the airplane back to a serviceable condition.
2. Part 2 - Slat Track Housing Repair
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
29 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 30

a. Remove the slat track. For the inboard slats, refer to 757 AMM 27-81-10 as an accepted
procedure and for the outboard slats, refer to 757 AMM 27-81-12 as an accepted procedure.
b. Blend out damage in accordance with FIGURE 11.
c. Remove any foreign object debris from the slat track housing.
d. Install the slat track. For the inboard slats, refer to 757 AMM 27-81-10 as an accepted
procedure and for the outboard slats, refer to 757 AMM 27-81-12 as an accepted procedure.
e. It is optional to lubricate the slats, if necessary. Refer to 757 AMM 12-21-08 as an accepted
procedure.
3. Part 3 - Appendix A: Inspection Results Report
a. If any of the following conditions are found during the Part 1 inspections, complete Appendix
A and send the results to Boeing:
– Main track downstop assembly order is incorrect
– Main track downstop assembly part is missing or damaged
– Foreign object debris found in the slat track housing
– Damage found in the slat track housing that results in a remaining thickness of 0.040
inches or greater
– Damage found in the slat track housing that results in a remaining thickness of less than
0.040 inches or a crack is found.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1: July 19, 2011
30 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 31 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
A-
7  A-
SLAT
MAIN
TRACK
A-A
TYPICAL MAIN TRACK
(7 LOCATIONS)
BUSHING
STOP
BOLT
NUT
STOP
TYPICAL MAIN TRACK  1579156
DOWNSTOP ASSEMBLY
FIGURE 1: LEFT WING - SLAT NUMBERS 1, 2, 3 AND 4 - DETAILED INSPECTION OF MAIN TRACK
DOWNSTOP ASSEMBLIES
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  31 of 54

### Page 32

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)7-BoltInspect1
(a) (b) (c)7-StopInspect
(a) (b) (c)7-BushingInspect
(a) (b) (c)7-StopInspect
(a) (b) (c)7-NutInspect
(a) Do a detailed inspection for the correct assembly order as shown and for missing or damaged parts.
(b) The main track downstop assembly can be inspected by using a one inch extendable mirror or similar
mirror, placed between the two ribs. The main track downstop assembly can also be viewed through the
access hole in the ribs on each side of the slat track. Disassembly of the main track downstop is not required
to accomplish this inspection.
(c) If necessary to line up the main track downstop with the access hole in the ribs, disconnect the slat actu-
ator from the leading edge slats. Refer to 757 AMM 27-81-18 as an accepted procedure. Manually extend
the track until the main track downstop hole in the track lines up with the access hole in the main track
ribs.
FIGURE 1: LEFT WING - SLAT NUMBERS 1, 2, 3 AND 4 - DETAILED INSPECTION OF MAIN TRACK
DOWNSTOP ASSEMBLIES
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
32 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 33 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
INBOARD
SLAT
MAIN
A-A  FWD
TRACK
TYPICAL MAIN TRACK
(2 LOCATIONS)
ROCKER
BUSHING  DOWNSTOP
BOLT
MAIN  TRACK  WASHER
NUT
BUSHING  WASHER
TYPICAL MAIN TRACK
DOWNSTOP ASSEMBLY
(2 LOCATIONS)
FIGURE 2: LEFT WING - SLAT NUMBER 5 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  33 of 54

### Page 34

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)2-BoltInspect1
(a) (b) (c)2-WasherInspect
(a) (b) (c)2-BushingInspect
(a) (b) (c)2-Rocker DownstopInspect
(a) (b) (c)2-BushingInspect
(a) (b) (c)2-WasherInspect
(a) (b) (c)2-NutInspect
(a) Do a detailed inspection for the correct assembly order as shown and for missing or damaged parts.
(b) The main track downstop assembly can be inspected by using a one inch extendable mirror or similar
mirror, placed between the two ribs. The main track downstop assembly can also be viewed through the
access hole in the ribs on each side of the slat track. Disassembly of the main track downstop is not required
to accomplish this inspection.
(c) If necessary to line up the main track downstop with the access hole in the ribs, disconnect the slat actu-
ator from the leading edge slats. Refer to 757 AMM 27-81-18 as an accepted procedure. Manually extend
the track until the main track downstop hole in the track lines up with the access hole in the main track
ribs.
FIGURE 2: LEFT WING - SLAT NUMBER 5 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
34 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 35 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
- A
- A
SLAT
MAIN
TRACK
A-A
TYPICAL MAIN TRACK
(7 LOCATIONS)
BUSHING
STOP
BOLT
NUT
STOP
DOWNSTOP ASSEMBLY  TYPICAL MAIN TRACK  1579157
(7 LOCATIONS)
FIGURE 3: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - DETAILED INSPECTION OF MAIN TRACK
_ DOWNSTOP ASSEMBLIES
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  35 of 54

### Page 36

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)7-BoltInspect1
(a) (b) (c)7-StopInspect
(a) (b) (c)7-BushingInspect
(a) (b) (c)7-StopInspect
(a) (b) (c)7-NutInspect
(a) Do a detailed inspection for the correct assembly order as shown and for missing or damaged parts.
(b) The main track downstop assembly can be inspected by using a one inch extendable mirror or similar
mirror, placed between the two ribs. The main track downstop assembly can also be viewed through the
access hole in the ribs on each side of the slat track. Disassembly of the main track downstop is not required
to accomplish this inspection.
(c) If necessary to line up the main track downstop with the access hole in the ribs, disconnect the slat actu-
ator from the leading edge slats. Refer to 757 AMM 27-81-18 as an accepted procedure. Manually extend
the track until the main track downstop hole in the track lines up with the access hole in the main track
ribs.
FIGURE 3: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - DETAILED INSPECTION OF MAIN TRACK
DOWNSTOP ASSEMBLIES
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
36 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 37 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
INBOARD
SLAT
FWD  A-A  MAIN
TYPICAL MAIN TRACK  TRACK
(2 LOCATIONS)
ROCKER
DOWNSTOP  BUSHING
BOLT
WASHER
MAIN
NUT  TRACK
BUSHING
WASHER
DOWNSTOP ASSEMBLY  TYPICAL MAIN TRACK  1579158
(2 LOCATIONS)
FIGURE 4: RIGHT WING - SLAT NUMBER 6 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  37 of 54

### Page 38

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b) (c)2-BoltInspect1
(a) (b) (c)2-WasherInspect
(a) (b) (c)2-BushingInspect
(a) (b) (c)2-Rocker DownstopInspect
(a) (b) (c)2-BushingInspect
(a) (b) (c)2-WasherInspect
(a) (b) (c)2-NutInspect
(a) Do a detailed inspection for the correct assembly order as shown and for missing or damaged parts.
(b) The main track downstop assembly can be inspected by using a one inch extendable mirror or similar
mirror, placed between the two ribs. The main track downstop assembly can also be viewed through the
access hole in the ribs on each side of the slat track. Disassembly of the main track downstop is not required
to accomplish this inspection.
(c) If necessary to line up the main track downstop with the access hole in the ribs, disconnect the slat actu-
ator from the leading edge slats. Refer to 757 AMM 27-81-18 as an accepted procedure. Manually extend
the track until the main track downstop hole in the track lines up with the access hole in the main track
ribs.
FIGURE 4: RIGHT WING - SLAT NUMBER 6 - DETAILED INSPECTION OF MAIN TRACK DOWNSTOP
ASSEMBLIES
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
38 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 39 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
RIB
FRONT
SPAR
INBD
SLAT
TRACK
YPICAL SLAT TRAC  1579159
OUSING ASSEMBL
(11 LOCATIONS)
FIGURE 5: LEFT WING - SLAT NUMBER 1, 2, 3, 4 AND 5 - DETAILED INSPECTION OF SLAT TRACK
HOUSING
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  Copyright © Unpublished Work - See page 1 for details.  BOEING PROPRIETARY -  757-57-0068  39 of 54

### Page 40

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)11-Slat Track HousingInspect1
(a) Do a detailed inspection of the slat track housing for any foreign object debris and damage to the wall of
the slat track housing.
(b) A borescope is recommended to do this inspection. The borescope can be inserted into the slat track
housing through the forward opening of the slat track housing.
FIGURE 5: LEFT WING - SLAT NUMBER 1, 2, 3, 4 AND 5 - DETAILED INSPECTION OF SLAT TRACK
HOUSING
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
40 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 41 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
RIB
FRONT
SPAR
SLAT
TRACK
TYPICAL SLAT TRACK  HOUSING ASSEMBLY  1579160
(11 LOCATIONS)
FIGURE 6: RIGHT WING - SLAT NUMBER 6, 7,8, 9 AND 10 - DETAILED INSPECTION OF SLAT TRACK
HOUSING
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  41 of 54

### Page 42

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a) (b)11-Slat Track HousingInspect1
(a) Do a detailed Inspection of the slat track housing for any foreign object debris and damage to the wall of
the slat track housing.
(b) A borescope is recommended to do this inspection. The borescope can be inserted into the slat track
housing through the forward opening of the slat track housing.
FIGURE 6: RIGHT WING - SLAT NUMBER 6, 7, 8, 9 AND 10 - DETAILED INSPECTION OF SLAT TRACK
HOUSING
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
42 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 43 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
пати
SLAT
MAIN  FWD
TRACK
А-А
TYPICAL MAIN TRACK
(7 LOCATIONS)
BUSHING
BOLT
STOP
NUT
STOP
TYPICAL MAIN TRACK
DOWNSTOP ASSEMBLY  1579161
(7 LOCATIONS)
FIGURE 7: LEFT WING - SLAT NUMBER 1, 2, 3 AND 4 - MAIN TRACK DOWNSTOP ASSEMBLY NUT -
TORQUE APPLICATION
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  43 of 54

### Page 44

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)7-NutTorque1
(a) Hold the main track downstop assembly bolt head and tighten the nut within the torque range of 30 - 40
in-lbs.
FIGURE 7: LEFT WING - SLAT NUMBER 1, 2, 3 AND 4 - MAIN TRACK DOWNSTOP ASSEMBLY NUT -
TORQUE APPLICATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
44 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 45 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
SLAT,
A-A
TYPICAL MAIN TRACK  FWD
(2 LOCATIONS)
ROCKER
DOWNSTOP
BUSHING
BOLT
WASHER
MAIN
TRACK
(2) NUT
BUSHING
WASHER
TYPICAL MAIN TRACK  1579162
DOWNSTOP ASSEMBLY
(2 LOCATIONS)
FIGURE 8: LEFT WING - SLAT NUMBER 5 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  45 of 54

### Page 46

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(b)2SIZENutInspect1
WARNING: MAKE SURE TO APPLY THE TORQUE APPLICABLE TO THE SIZE NUT INSTALLED ON
YOUR MAIN SLAT TRACK. IF THE WRONG TORQUE IS APPLIED TO THE NUT, FOREIGN
OBJECT DEBRIS MAY BE INTRODUCED INTO THE SLAT CAN.
(a)21/4 INCH DIAMETERNutTorque2
(c)23/8 INCH DIAMETERNutTorque
(a) Hold the main track downstop assembly bolt head and tighten the nut within the torque range of 60 - 70
in-lbs.
(b) The slat track downstops will have either 1/4 inch diameter hardware (size 4) or 3/8 inch diameter hardware
(size 6).
(c) Hold the main track downstop assembly bolt head and tighten the nut within the torque range of 194 -
206 in-lbs.
FIGURE 8: LEFT WING - SLAT NUMBER 5 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
46 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 47 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
SLAT
MAIN
TRACK
A-A
TYPICAL MAIN TRACK
(7 LOCATIONS)
BUSHING
BOLT
STOP
NUT
STOP
TYPICAL MAIN TRACK  1579163
DOWNSTOP ASSEMBLY
(7 LOCATIONS)
FIGURE 9: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - MAIN TRACK DOWNSTOP ASSEMBLY NUT
- TORQUE APPLICATION
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  757-57-0068
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  47 of 54

### Page 48

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)7-NutTorque1
(a) Hold the main track downstop assembly bolt head and tighten the nut within the torque range of 30 - 40
in-lbs.
FIGURE 9: RIGHT WING - SLAT NUMBERS 7, 8, 9 AND 10 - MAIN TRACK DOWNSTOP ASSEMBLY NUT
- TORQUE APPLICATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
48 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 49 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
SLAT
A-A
FWD  TYPICAL MAIN TRACK
(2 LOCATIONS)
ROCKER
DOWNSTOP
BUSHING
BOLT
WASHER
MAIN
TRACK
NUT (1
BUSHING
WASHER
TYPICAL MAIN TRACK  1579164
DOWNSTOP ASSEMBLY
(2 LOCATIONS)
FIGURE 10: RIGHT WING - SLAT NUMBER 6 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  49 of 54

### Page 50

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(b)2SIZENutInspect1
WARNING: MAKE SURE TO APPLY THE TORQUE APPLICABLE TO THE SIZE NUT INSTALLED ON
YOUR MAIN SLAT TRACK. IF THE WRONG TORQUE IS APPLIED TO THE NUT, FOREIGN
OBJECT DEBRIS MAY BE INTRODUCED INTO THE SLAT CAN.
(a)21/4 INCH DIAMETERNutTorque2
(c)23/8 INCH DIAMETERNutTorque
(a) Hold main track downstop assembly bolt head and tighten the nut within the torque range of 60 - 70 in-
lbs.
(b) The slat track downstops will have either 1/4 inch diameter hardware (size 4) or 3/8 inch diameter hardware
(size 6).
(c) Hold the main track downstop assembly bolt head and tighten the nut within the torque range of 194 -
206 in-lbs.
FIGURE 10: RIGHT WING - SLAT NUMBER 6 - MAIN TRACK DOWNSTOP ASSEMBLY NUT - TORQUE
APPLICATION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
50 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 51 (OCR)

BOEING SERVICE BULLETIN 757-57-0068
INSIDE SURFACE
OF SLAT TRACK
HOUSING
TYPICAL SLAT TRACK HOUSING
& OF DAMAGE
234 RELA OF MATERIAL  REMOVEL
0.04 INCH
MINIMUM
REMOVAL OF DAMAGE  1664573
FIGURE 11: WINGS - SLAT NUMBERS 1 - 10 SLAT TRACK HOUSING - REPAIR
(SHEET 1 OF 2)
Original Issue: September 15, 2009
Revision 1 July 19, 2011  BOEING PROPRIETARY -  757-57-0068
Copyright © Unpublished Work - See page 1 for details.  51 of 54

### Page 52

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
(a)--DamageRemove1
(b)--Slat Track HousingClean2
(c)-ALODINE 600Chemical Conversion
Coating
Apply3
(d)-BMS 10-20 TYPE IIPrimerApply4
(a) Remove all nicks, gouges or scratches from the inside surface of the slat track housing to a 1.00 inch
radius minimum and blend out the damaged area.
(b) Clean the damaged area with a soft cloth moist with cleaning solvent. Refer to SOPM 20-30-03 as an
accepted procedure
(c) Apply to the repair area. Refer to SOPM 20-43-03 as an accepted procedure.
(d) Apply one coat to the repair area. Refer to SOPM 20-41-02 as an accepted procedure.
FIGURE 11: WINGS - SLAT NUMBERS 1 - 10 SLAT TRACK HOUSING - REPAIR
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
52 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 53

Reporting Instructions:
1. Record the airplane registry, variable or line number.
2. If a reportable condition is found, mark an 'X' in the applicable condition column for the applicable slat number
and end where the condition was found, and provide a detailed explanation of what was found in the comments
section.
3. Send the inspection results report to Boeing through the Boeing Communications System (BCS).
Service Bulletin 757-57-0068 inspection results report
Airplane Registry, Variable or Line Number:
ConditionSlat
Damage
found in the
slat track
housing that
results in a
remaining
thickness
less than
0.040 inches
or a crack is
found
Damage
found in the
slat track
housing that
results in a
remaining
thickness of
0.040 inches
or greater
Foreign ob-
ject debris
found in the
slat track
housing
Main track
downstop as-
sembly part
is missing or
damaged
Main track
downstop as-
sembly order
is incorrect
EndNumber
Inbd1
N/AN/AOutbd
Inbd2
Outbd
Inbd3
Outbd
Inbd4
Outbd
Inbd5
Outbd
Inbd6
Outbd
Inbd7
Outbd
APPENDIX A: INSPECTION RESULTS REPORT
(SHEET 1 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
53 of 54
BOEING SERVICE BULLETIN 757-57-0068

### Page 54

Service Bulletin 757-57-0068 inspection results report
Airplane Registry, Variable or Line Number:
ConditionSlat
Damage
found in the
slat track
housing that
results in a
remaining
thickness
less than
0.040 inches
or a crack is
found
Damage
found in the
slat track
housing that
results in a
remaining
thickness of
0.040 inches
or greater
Foreign ob-
ject debris
found in the
slat track
housing
Main track
downstop as-
sembly part
is missing or
damaged
Main track
downstop as-
sembly order
is incorrect
EndNumber
Inbd8
Outbd
Inbd9
Outbd
Inbd10
N/AN/AOutbd
Comments:
APPENDIX A: INSPECTION RESULTS REPORT
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: September 15, 2009
757-57-0068Revision 1 July 19, 2011
54 of 54
BOEING SERVICE BULLETIN 757-57-0068

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
