# Boeing Service Bulletin 767-23-0164: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2011-0382; AD 2011-25-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 767-23-0164](https://openairdocs.org/service-documents/boeing/sb-767-23-0164.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin (7)
- Pages: 33
- PDF: https://openairdocs.org/files/sha256/51/79/5179d4331aa3556c31a9da2a4c81fe06cb60eb1eb3e70d051e4467160921ba84
- Page: https://openairdocs.org/service-documents/boeing/sb-767-23-0164/file/5179d4331aa3

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial
Airplane
Group
767
Service Bulletin
Number: 767-23-0164 SummaryDate: May 31, 2001
ATA System: 2342
SUBJECT: COMMUNICATIONS - Interphone - Cabin Interphone System - Audio Accessory Unit And
Handset Replacement
CONCURRENT REQUIREMENTS
For airplane VS303, you cannot make the changes
given in this service bulletin unless the changes
given in Boeing Service Bulletin 767-23-0160 are
made.
BACKGROUND
This service bulletin gives instructions to replace the
pilots' and attendant handsets and, on airplanes
VR051-VR057, replace the audio accessory unit
(AAU). These changes will prevent handset audio
feedback that can occur when the handsets are
used.
An operator with the new look interior (NLI)
configuration reported feedback during handset use.
Investigation at Boeing found that when the handset
microphone gain is reduced by 3db and the AAU
gain is reduced by 9db the audio feedback does not
occur. The new handsets and AAU have the
reduced gain to prevent handset audio feedback.
ACTION (PRR B13023-1)
In the flight compartment replace the pilots' handset
on the P8 panel. In the passenger cabin, replace 5
attendant handsets.
On airplanes VR051-VR057, replace the audio
accessory unit (AAU) on the E2-5 shelf in the main
equipment center.
NOTE: On airplane VS303, the AAU is replaced by
Service Bulletin 767-23-0160.
Do a system test of the cabin interphone system.
EFFECTIVITY
Operator Airplanes
CAL VR051-VR057
LAL VS303
COMPLIANCE
No compliance time is given.
INDUSTRY SUPPORT INFORMATION
At the time of release of this service bulletin,
warranty remedies have not been determined. A
subsequent revision or Information Notice will
address the warranty remedies available, if any.
MANPOWER
Total Elapsed Time
Airplanes Man-Hours (Hours)
VR051-VR057 2.0 1.5
VS303 1.0 1.0
The changes to the AAU and handsets as given in
the Boeing Component service bulletins are not
included.
MATERIAL INFORMATION
Operator Supplied Parts/Materials
767-23-0164
Summary Page 1 of 2

### Page 2

BOEING SERVICE BULLETIN 767-23-0164
ON AIRPLANES VR051−VR057,
REPLACE THE ATTENDANT HANDSET
AT FIVE ATTENDANT SEAT LOCATIONS,
REPLACE THE AUDIO ACCESSORY
UNIT ON THE E2−5 SHELF
HANDSET
COMPARTMENT, REPLACE THE PILOTS'
ON THE P8 PANEL IN THE FLIGHT
FWD
MAIN EQUIPMENT CENTER
V52548
May 31, 2001 767-23-0164
Summary Page 2 of 2

### Page 3

Commercial
Airplane
Group
767
Service Bulletin
Number: 767-23-0164
Date: May 31, 2001
ATA System: 2342
SUBJECT: COMMUNICATIONS - Interphone - Cabin Interphone System - Audio Accessory Unit And
Handset Replacement
1. PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624T001, Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below. An equivalent change is on subsequent
production airplanes. Refer to PRRB13023-1 for data about this change.
Airplane Models:
767-200 767-300
IDENTIFICATION BY CUSTOMER, CUSTOMER CODE, GROUP AND VARIABLE NUMBER
CONTINENTAL AIRLINES (CAL)
VR051-VR057
LAUDA AIR (LAL)
VS303
IDENTIFICATION BY VARIABLE NUMBER
VR051-VR057 VS303
2. Spares Affected
Examine your spares supply for the parts identified in Paragraph 2.E., Existing Parts
Accountability. If any parts are found, refer to Paragraph 2.E. for the recommended use.
May 31, 2001 767-23-0164
Page 1 of 30

### Page 4

BOEING SERVICE BULLETIN 767-23-0164
B. Concurrent Requirements
For VS303, you cannot make the changes given in this service bulletin unless the changes given in
Boeing Service Bulletin 767-23-0160 are made.
C. Reason
This service bulletin gives instructions to replace the pilots' and attendant handsets and, on airplanes
VR051-VR057, replace the audio accessory unit (AAU). These changes will prevent handset audio
feedback that can occur when the handsets are used.
An operator with the new look interior (NLI) configuration reported feedback during handset use.
Investigation at Boeing found that when the handset microphone gain is reduced by 3db and the AAU
gain is reduced by 9db the audio feedback does not occur. The new handsets and AAU have the
reduced gain to prevent handset audio feedback.
D. Description
In the flight compartment replace the pilots' handset on the P8 panel. In the passenger cabin, replace
5 attendant handsets.
On airplanes VR051-VR057, replace the audio accessory unit (AAU) on the E2-5 shelf in the main
equipment center.
NOTE: On airplane VS303, the AAU is replaced by Service Bulletin 767-23-0160.
Do a system test of the cabin interphone system.
An evaluation form is attached to this service bulletin. Please use this form to tell us what you think
of the quality of this service bulletin.
E. Compliance
No compliance time is given.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this service bulletin comply with the applicable Federal Aviation Regulations (FAR) and
are FAA approved. This service bulletin and the FAA approval were based on the airplane in its
original Boeing delivery configuration or as modified by other FAA approved Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also
affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory
agency approval before incorporating this service bulletin.
May 31, 2001 767-23-0164
2

### Page 5

BOEING SERVICE BULLETIN 767-23-0164
G. Manpower
The table below shows an estimate of the man-hours necessary to do this change for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
man-hour data if necessary. The estimate does not include lost time. These are some examples of
lost time:
- Time to adjust to the workplace
- Time to schedule the work
- Time to examine the work
- Time to cure the materials
- Time to make the parts
- Time to find the tools.
AIRPLANES VR051-VR057
Task Number of Persons Man-Hours Elapsed Time (Hours)
Replace AAU 1 0.5 0.5
Replace
Handsets
1 0.5 0.5
Test 2 1.0 0.5
TOTAL FOR EACH AIRPLANE 2.0 1.5
AIRPLANE VS303
Task Number of Persons Man-Hours Elapsed Time (Hours)
Replace
Handsets
1 0.5 0.5
Test 1 0.5 0.5
TOTAL FOR EACH AIRPLANE 1.0 1.0
The change to the AAU as given in Boeing Component Service Bulletin 285T0001-23-09 is not
included.
The change to the handsets as given in Boeing Component Service Bulletin 285W0024-23-04 is not
included.
H. Weight and Balance Changes
None
I. Electrical Load Data
Not changed
May 31, 2001 767-23-0164
3

### Page 6

BOEING SERVICE BULLETIN 767-23-0164
J. References
1. Existing Data:
a. Engineering Change Memo PRRB13023-1
b. 767 Maintenance Manual (AMM) Subject 23-42-01/401
c. Boeing Standard Overhaul Practices Manual (BSOPM) 20-50-05
d. Boeing Service Bulletin 767-23-0160, "COMMUNICATION - Audio Accessory Unit
Replacement"
e. Boeing Component Service Bulletin 285T0001-23-09, "COMMUNICATION - Audio Accessory
Unit Modification"
f. Boeing Component Service Bulletin 285W0024-23-04, "COMMUNICATIONS - Interphone -
Cabin Interphone System - Cabin Attendant / Flight Deck Handset Module Assembly -
Microphone Gain Reduction"
2. Data supplied with this service bulletin:
None
3. Installation Drawings Used in the Preparation of This Service Bulletin:
None
K. Publications Changed
Publication Chapter-Section
767 Maintenance Manual 23-42, 23-51
767 Fault Isolation Manual 23-42, 23-51
767 Illustrated Parts Catalog 23-42, 25-71, 31-11
L. Interchangeability and Intermixability of Parts
Refer to Paragraph 2.E., Existing Parts Accountability, for interchangeability and intermixability
information.
May 31, 2001 767-23-0164
4

### Page 7

BOEING SERVICE BULLETIN 767-23-0164
2. MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary For Each
Airplane, and Paragraph 2.D., Parts Necessary to Change Spares. Refer to Boeing Component
Service Bulletins 285T0001-23-09 and 285W0024-23-04.
B. Industry Support Information
At the time of release of this service bulletin, warranty remedies have not been determined. A
subsequent revision or Information Notice will address the warranty remedies available, if any.
C. Parts Necessary For Each Airplane
1. Kits:
None
2. Parts and Materials Supplied by the Operator:
AIRPLANES VR051-VR057
QTY Part Number Name
1 285T0001-302 (a) Audio Accessory Unit (AAU)
5 285W0024-7L (b) Attendant Handset
1 285W0024-8A (b) Pilots' Handset
1 (c) BAC27TEX6744 Dialing Codes Marker (Pilot's Handset)
5 (c) BAC27TEX6745 Dialing Codes Marker (Attendant
Handset)
(a) To get AAU 285T0001-302, change AAU 285T0001-301 as given in Boeing
Component Service Bulletin 285T0001-23-09.
(b) To get handsets 285W0024-7L and 285W0024-8A, change handsets
285W0024-1L and 285W0024-4A as given in Boeing Component Service
Bulletin 285W0024-23-04
(c) If necessary. Refer to the Accomplishment Instructions.
AIRPLANE VS303
QTY Part Number Name
5 285W0024-7H (a) Attendant Handset
1 285W0024-8A (a) Pilots' Handset
1 (b) BAC27TEX6686 Dialing Codes Marker (Pilots' Handset)
5 (b) BAC27TEX6687 Dialing Codes Marker (Attendant
Handset)
(a) To get handsets 285W0024-7H and 285W0024-8A, change handsets
285W0024-1H and 285W0024-4A as given in Boeing Component Service
Bulletin 285W0024-23-04
(b) If necessary. Refer to the Accomplishment Instructions.
May 31, 2001 767-23-0164
5

### Page 8

BOEING SERVICE BULLETIN 767-23-0164
D. Parts Necessary to Change Spares
Refer to Boeing Component Service Bulletins 285T0001-23-09 and 285W0024-23-04
E. Existing Parts Accountability
The parts shown below are changed as shown in this service bulletin. Quantity (QTY) is the number
of parts changed on each airplane.
Existing Part Number RUC Name QTY New Part Number PNC RC
285T0001-301 (a) RW1 Audio Accessory Unit 1 285T0001-302 S A
285W0024-1L (a)
285W0024-1H (b)
RW2 Attendant Handset 5 285W0024-7L (a)
285W0024-7H (b)
S A
285W0024-4A RW2 Pilot's Handset 1 285W0024-8A S A
(a) Airplanes VR051-VR057
(b) Airplane VS303
RUC Recommended Use Code
RW1 - Make the change given in Boeing Component Service Bulletin 285T0001-23-09.
RW2 - Make the change given in Boeing Component Service Bulletin 285W0024-23-04.
PNC Part Number Code
S - This is the part number for the new equivalent or replacement part.
- To get a new part, use this part number in your order.
- This part is used in production.
RC Replacement Code
A - Do not use the existing part to replace the new or changed part.
F. Special Tooling - Price and Availability
None
G. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But,
maintenance and overhaul tools in the manuals given in Paragraph 1.J., References, can be
necessary. Examine operator tool supply to make sure all necessary tools are available.
May 31, 2001 767-23-0164
6

### Page 9

BOEING SERVICE BULLETIN 767-23-0164
3. ACCOMPLISHMENT INSTRUCTIONS
GENERAL NOTES
1. The paragraphs identified with a letter give the general work instructions and the necessary tests.
The instructions identified with numbers on the figures give the recommended sequence of steps.
2. Obey all of the warnings and cautions given in the specified manual sections.
WORK INSTRUCTIONS
A. In the flight compartment, replace the pilot's handset as shown in Figure 1.
B. In the passenger cabin, replace the attendant handsets as shown in Figure 2.
C. On airplanes VR051-VR057, do these steps to replace the audio accessory unit (AAU):
1. Open these circuit breakers and attach DO-NOT-CLOSE tags:
Location
(Panel/Position) Name Circuit Breaker
P11 / C21 PASS ADRS 2 C00558
P11 / C22 PASS ADRS 1 C00548
P11 / C24 INTERPHONE CABIN C01007
P11 / C25 DUAL PWR INTPH CAPT C01003
P11 / C26 DUAL PWR INTPH F/O C00646
P11 / C29 DUAL PWR INTPH CAPT C01004
P11 / G2 OBSERVER INTPH C01006
P11 / G30 DUAL PWR INTPH F/O C00647
2. In the main equipment center, replace the AAU in the main equipment center as shown in
Figure 3.
3. Remove the DO-NOT-CLOSE tags and close these circuit breakers:
Location
(Panel/Position) Name Circuit Breaker
P11 / C21 PASS ADRS 2 C00558
P11 / C22 PASS ADRS 1 C00548
P11 / C24 INTERPHONE CABIN C01007
P11 / C25 DUAL PWR INTPH CAPT C01003
P11 / C26 DUAL PWR INTPH F/O C00646
P11 / C29 DUAL PWR INTPH CAPT C01004
P11 / G2 OBSERVER INTPH C01006
P11 / G30 DUAL PWR INTPH F/O C00647
May 31, 2001 767-23-0164
7

### Page 10

BOEING SERVICE BULLETIN 767-23-0164
D. On airplanes VR051-VR057, do these steps to test the cabin interphone system:
NOTE: The functional test given below was included directly from a Boeing functional test
document. When the test was included in this service bulletin, the format, text, and step
numbers were not changed. There are two numbers associated with each instruction.
The number to the left is the sequence number which must be followed when you do the
test. The number to the right of it is the "step" number. The step number is the actual
number associated with the Boeing functional test document. The step number is
referenced when repeat instructions are required within the functional test.
1. STEP 102
CAUTION ELECTRICAL POWER
Potential Electrical Power Hazard exists when performing
this test. Use applicable Shop procedures as required.
2. STEP 200
Tools and/or Equipment
3. STEP 201
Use the following listed equipment to perform test:
- Shop Supply AR Boom Mic
4. STEP 202
VERIFY that test equipment used on this job, but not
listed in this section, is documented using the
appropriate method for recording non-conformities.
5. STEP 300
References
6. STEP 301
Wiring Diagrams
NUMBER TITLE
-------- ----------------------------------------
23-31-11 Passenger Address Voice Input Circuitry
23-31-13 Passenger Address Output Circuitry/Controls
23-42-11 Cabin Interphone
23-42-12 Cabin Interphone - Electrical Chime
7. STEP 302
Schematics
NUMBER TITLE
-------- ----------------------------------------
23-31-10 Passenger Address - Microphone and Input
Controls
23-31-30 Passenger Address - Speaker Bus 1
23-31-40 Passenger Address - Speaker Bus 2
23-42-10 Cabin Interphone - Handset Interfaces
23-42-20 Cabin Interphone - Master Call Lights
23-42-30 Cabin Interphone - Chime Outputs
23-42-40 Cabin Interphone - Pilots Call Panel
23-42-50 Cabin Interphone - Flight/Cabin/Service
23-42-60 Cabin Interphone - Passenger Address
May 31, 2001 767-23-0164
8

### Page 11

BOEING SERVICE BULLETIN 767-23-0164
8. STEP 400
General Information
9. STEP 404
Abbreviations and acronyms used in this test:
AAU Audio Accessory Unit
AR As Required
DCU Data Concentrator Unit
EICAS Engine Indication and Crew Alerting System
LRU Line Replaceable Unit
PA Passenger Address
PTT Push To Talk
10. STEP 500
START Test Setup
11. STEP 501
ENSURE the following circuit breakers on the P11 panel
are closed:
(3 ACP/ASP)
CB NO. LOC NOMENCLATURE
------ --- ------------------
C00548 C22 PASS. ADRS 1
C00558 C21 PASS. ADRS 2
C01007 C27 INTERPHONE-CABIN
C00646 C26 DUAL PWR INTPH F/0
C00647 G30 DUAL PWR INTPH F/O
C01003 C25 DUAL PWR INTPH CAPT
C01004 C29 DUAL PWR INTPH CAPT
C01006 G02 OBSERVER INTPH
12. STEP 502
ENSURE all handsets are securely placed in their
cradles.
13. STEP 503
STOP Test Setup
14. STEP 600
START Pilots Call Panel Test
15. STEP 601
DO dial "31" on a FWD attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
16. STEP 602
VERIFY the following:
1. HI chime is heard in the flight deck
2. FWD call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Control Panels
4. CABIN CALL illuminates on the EICAS computer displays
May 31, 2001 767-23-0164
9

### Page 12

BOEING SERVICE BULLETIN 767-23-0164
17. STEP 603
PRESS the FWD call button on the Pilots Call Panel.
18. STEP 604
VERIFY the following:
1. FWD button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Control Panels
3. CABIN CALL extinguishes on the EICAS computer displays
19. STEP 605
PUT the FWD handset back in the cradle.
20. STEP 606
DO dial "31" on the MID attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
21. STEP 607
VERIFY the following:
1. HI chime is heard in the flight deck
2. MID call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Control Panels
4. CABIN CALL illuminates on the EICAS computer displays
22. STEP 608
PRESS the MID call button on the Pilots Call Panel.
23. STEP 609
VERIFY the following:
1. MID button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Control Panels
3. CABIN CALL extinguishes on the EICAS computer displays
24. STEP 610
PUT the MID handset back in the cradle.
25. STEP 611
DO dial "31" on a AFT attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
26. STEP 612
VERIFY the following:
1. HI chime is heard in the flight deck
2. AFT call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Control Panels
4. CABIN CALL illuminates on the EICAS computer displays
27. STEP 613
PRESS the AFT call button on the Pilots Call Panel.
May 31, 2001 767-23-0164
10

### Page 13

BOEING SERVICE BULLETIN 767-23-0164
28. STEP 614
VERIFY the following:
1. AFT button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Control Panels
3. CABIN CALL extinguishes on the EICAS computer displays
29. STEP 615
PUT the AFT handset back in the cradle.
30. STEP 616
DO dial "31" on a FWD attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
31. STEP 617
VERIFY the following:
1. HI chime is heard in the flight deck
2. FWD call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Control Panels
4. CABIN CALL illuminates on the EICAS computer displays
32. STEP 618
PRESS the CAB button on the CAPT Audio Control Panel.
33. STEP 619
VERIFY the following:
1. FWD button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Control Panels
3. CABIN CALL extinguishes on the EICAS computer displays
34. STEP 620
PUT the FWD handset back in the cradle.
35. STEP 621
PRESS the ALERT call button on the Pilots Call Panel
36. STEP 622
VERIFY the following:
1. Three (3) hi/lo chimes are produced by the PA speakers
2. 4 Pink Attnd. call lights flash at FWD ATTENDANT STATIONS
3. 2 Pink Attnd. call lights flash at MID ATTENDANT STATIONS
4. 3 Pink Attnd. call lights flash at AFT ATTENDANT STATIONS
37. STEP 623
DO dial "**" on the FWD-L Attendant handset.
38. STEP 624
VERIFY the following:
1. Three (3) hi/lo chimes are produced by the PA speakers
2. The FWD-L Pink flashing Attnd. call light extinguishes
3. CABIN ALERT illuminates on the EICAS Computer Displays
May 31, 2001 767-23-0164
11

### Page 14

BOEING SERVICE BULLETIN 767-23-0164
39. STEP 625
OPEN the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C27 INTERPHONE-CABIN
40. STEP 626
VERIFY the flashing Pink Attnd. call lights extinguish.
41. STEP 627
PUT the FWD-L handset back in the cradle.
42. STEP 628
CLOSE the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C27 INTERPHONE-CABIN
43. STEP 629
PRESS the FWD call button on the Pilot Call Panel.
44. STEP 630
VERIFY a hi/lo chime is produced by the 2 electronic
chime modules at the FWD attendant station.
45. STEP 631
PRESS the MID call button on the Pilot Call Panel.
46. STEP 632
VERIFY a hi/lo chime is produced by 1 electronic
chime module at the MID attendant station.
47. STEP 633
PRESS the AFT call button on the Pilot Call Panel.
48. STEP 634
VERIFY a hi/lo chime is produced by 2 electronic
chime module at the AFT attendant station.
49. STEP 635
OPEN the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C27 INTERPHONE-CABIN
50. STEP 636
VERIFY the attendant call lights extinguish.
51. STEP 637
CLOSE the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C27 INTERPHONE-CABIN
May 31, 2001 767-23-0164
12

### Page 15

BOEING SERVICE BULLETIN 767-23-0164
52. STEP 638
STOP Pilots Call Panel Test
53. STEP 700
START Audio Control/Selector Panels Test
54. STEP 701
ADJUST the three (3) flight deck Audio Control/Selector
Panels to the following configuration:
A. CAB mic selector switch depressed.
B. BOOM/OXY switch in BOOM position.
C. All on/off volume controls "OFF" except CAB, which
is to be "ON" with volume approximately midpoint.
55. STEP 702
REMOVE a FWD attendant handset from its cradle.
56. STEP 703
SPEAK into a boom microphone/headset at each audio
control/selector panel and into the FWD attendant
handset.
NOTE:
Press the audio control/selector panel PTT switch
when speaking into the boom microphone/headset.
57. STEP 704
VERIFY good quality 2-way voice communication between
the FWD attendant handset and the boom
microphone/headsets.
58. STEP 705
PUT the FWD handset back in the cradle.
59. STEP 706
STOP Audio Control/Selector Panels Test
60. STEP 800
START Pilot Handset Test
61. STEP 801
DO dial "46" on the Flight Deck Handset.
62. STEP 802
SPEAK into the Handset Microphone.
63. STEP 803
VERIFY the announcement is NOT audible over the PA
speakers.
64. STEP 804
PRESS and hold the PTT button on the Flight Deck
Handset.
May 31, 2001 767-23-0164
13

### Page 16

BOEING SERVICE BULLETIN 767-23-0164
65. STEP 805
VERIFY the announcement is clearly audible over the PA
speakers.
66. STEP 806
PUT the Flight Deck handset back in the cradle.
67. STEP 807
STOP Pilot Handset Test
68. STEP 900
START Handset Audio Test
69. STEP 901
VERIFY good quality 2-way voice communication between
the FWD1-L attendant handset and each of the following
handsets:
1. FWD-R Handset
2. MID-C Handset
3. AFT-L Handset
4. AFT-R Handset
NOTE:
Return the above handsets to their cradles after
verifying 2-way communication.
70. STEP 902
ENSURE all the handsets are in their cradles.
71. STEP 903
STOP Handset Audio Test
72. STEP 1000
START Attendant to PA Test
73. STEP 1001
ENSURE the PA system can be operated by performing the
following steps at each handset:
A. Remove the handset from cradle.
B. Dial "46" on the handset.
C. Speak into the handset.
D. Verify announcement is not heard over the PA system.
E. Push and hold the PTT button on the handset.
F. Verify announcement is clearly audible over
the PA system.
G. Replace the handset in cradle.
74. STEP 1002
VERIFY that the previous steps were performed and PASSED
for the following handsets:
1. FWD-L Handset
2. FWD-R Handset
3. MID-C Handset
4. AFT-L Handset
5. AFT-R Handset
May 31, 2001 767-23-0164
14

### Page 17

BOEING SERVICE BULLETIN 767-23-0164
75. STEP 1003
STOP Attendant to PA Test
76. STEP 1100
START AAU Handset Port Verification Test
77. STEP 1101
ENSURE correct handset port interface by performing the
following steps for all cabin attendant handsets:
A. Remove the handset from cradle.
B. DO dial the dial code assigned to the handsets station.
C. Verify the PINK Attnd. call lights at the handset's
station do not illuminate.
D. Replace the handset in cradle.
NOTE:
1. Assigned Dial Codes for handset locations are as
follows:
FWD-L = DOOR 1 L 11
FWD-R = DOOR 1 R 21
MID-C = OVERWING 34
AFT-L = DOOR 2 L 12
AFT-R = DOOR 2 22
2. Call light(s) will illuminate at the opposite
station for FWD and AFT handsets including Repeater
Bar Call Lights.
78. STEP 1102
VERIFY that the previous steps were performed and PASSED
for the listed handset:
1. FWD-L Handset
2. FWD-R Handset
3. MID-C Handset
4. AFT-L Handset
5. AFT-R Handset
79. STEP 1103
STOP AAU Handset Port Verification Test
May 31, 2001 767-23-0164
15

### Page 18

BOEING SERVICE BULLETIN 767-23-0164
E. On airplane VS303, do these steps to test the cabin interphone system:
NOTE: The functional test given below was included directly from a Boeing functional test
document. When the test was included in this service bulletin, the format, text, and step
numbers were not changed. There are two numbers associated with each instruction.
The number to the left is the sequence number which must be followed when you do the
test. The number to the right of it is the "step" number. The step number is the actual
number associated with the Boeing functional test document. The step number is
referenced when repeat instructions are required within the functional test.
1. STEP 102
CAUTION ELECTRICAL POWER
Potential Electrical Power Hazard exists when performing
this test. Use applicable Shop procedures as required.
2. STEP 200
Tools and/or Equipment
3. STEP 201
Use the following listed equipment to perform test:
- Shop Supply AR Boom Mic
4. STEP 202
VERIFY that test equipment used on this job, but not
listed in this section, is documented using the
appropriate method for recording non-conformities.
5. STEP 300
References
6. STEP 301
Wiring Diagrams
NUMBER TITLE
-------- ----------------------------------------
23-31-11 Passenger Address Voice Input Circuitry
23-31-13 Passenger Address Output Circuitry/Controls
23-42-11 Cabin Interphone
23-42-12 Cabin Interphone - Electrical Chime
7. STEP 302
Schematics
NUMBER TITLE
-------- ----------------------------------------
23-31-10 Passenger Address - Microphone and Input
Controls
23-31-30 Passenger Address - Speaker Bus 1
23-31-40 Passenger Address - Speaker Bus 2
23-42-10 Cabin Interphone - Handset Interfaces
23-42-20 Cabin Interphone - Master Call Lights
23-42-30 Cabin Interphone - Chime Outputs
23-42-40 Cabin Interphone - Pilots Call Panel
23-42-50 Cabin Interphone - Flight/Cabin/Service
23-42-60 Cabin Interphone - Passenger Address
May 31, 2001 767-23-0164
16

### Page 19

BOEING SERVICE BULLETIN 767-23-0164
8. STEP 400
General Information
9. STEP 404
Abbreviations and acronyms used in this test:
AAU Audio Accessory Unit
AR As Required
DCU Data Concentrator Unit
EICAS Engine Indication and Crew Alerting System
LRU Line Replaceable Unit
PA Passenger Address
PTT Push To Talk
10. STEP 500
START Test Setup
11. STEP 501
ENSURE the following circuit breakers on the P11 panel
are closed:
(4 ACP/ASP)
CB NO. LOC NOMENCLATURE
------ --- ------------------
C00548 C22 PASS. ADRS 1
C00558 C21 PASS. ADRS 2
C00551 C24 INTERPHONE-CABIN
C00648 C26 DUAL PWR INTPH F/0
C00649 G30 DUAL PWR INTPH F/O
C00644 C25 DUAL PWR INTPH CAPT
C00645 C29 DUAL PWR INTPH CAPT
12. STEP 502
ENSURE all handsets are securely placed in their cradles.
13. STEP 503
STOP Test Setup
14. STEP 600
START Pilots Call Panel Test
15. STEP 601
DO dial "31" on a FWD attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
16. STEP 602
VERIFY the following:
1. HI chime is heard in the flight deck
2. FWD call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Select Panels
4. CABIN CALL illuminates on the EICAS computer displays
17. STEP 603
PRESS the FWD call button on the Pilots Call Panel.
May 31, 2001 767-23-0164
17

### Page 20

BOEING SERVICE BULLETIN 767-23-0164
18. STEP 604
VERIFY the following:
1. FWD button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Select Panels
3. CABIN CALL extinguishes on the EICAS computer displays
19. STEP 605
PUT the FWD handset back in the cradle.
20. STEP 606
DO dial "31" on the MID attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
21. STEP 607
VERIFY the following:
1. HI chime is heard in the flight deck
2. MID call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Select Panels
4. CABIN CALL illuminates on the EICAS computer displays
22. STEP 608
PRESS the MID call button on the Pilots Call Panel.
23. STEP 609
VERIFY the following:
1. MID button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Select Panels
3. CABIN CALL extinguishes on the EICAS computer displays
24. STEP 610
PUT the MID handset back in the cradle.
25. STEP 611
DO dial "31" on a AFT attendant handset.
NOTE:
Ensure attendant handset is left off the cradle
until verification of flight deck indications.
26. STEP 612
VERIFY the following:
1. HI chime is heard in the flight deck
2. AFT call button illuminates on the PCP
3. CABIN CALL illuminates on the Audio Select Panels
4. CABIN CALL illuminates on the EICAS computer displays
27. STEP 613
PRESS the AFT call button on the Pilots Call Panel.
May 31, 2001 767-23-0164
18

### Page 21

BOEING SERVICE BULLETIN 767-23-0164
28. STEP 614
VERIFY the following:
1. AFT button extinguishes on the PCP
2. CABIN CALL extinguishes on the Audio Select Panels
3. CABIN CALL extinguishes on the EICAS computer displays
29. STEP 615
PUT the AFT handset back in the cradle.
30. STEP 616
PRESS the ALERT call button on the Pilots Call Panel
31. STEP 617
VERIFY the following:
1. Three (3) hi/lo chimes are produced by the PA speakers
2. 3 Pink Attnd. call lights flash at ATTENDANT STATIONS
3. 3 Pink Attnd. call lights flash at ATTENDANT STATIONS
4. 3 Pink Attnd. call lights flash at ATTENDANT STATIONS
32. STEP 618
DO dial "**" on the FWD-L Attendant handset.
33. STEP 619
VERIFY the following:
1. Three (3) hi/lo chimes are produced by the PA speakers
2. The FWD-L Pink flashing Attnd. call light extinguishes
3. CABIN ALERT illuminates on the EICAS Computer Displays
34. STEP 620
OPEN the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C24 INTERPHONE-CABIN SERVICE
35. STEP 621
VERIFY the flashing Pink Attnd. call lights extinguish.
36. STEP 622
CLOSE the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C24 INTERPHONE-CABIN SERVICE
37. STEP 623
PRESS the FWD call button on the Pilot Call Panel.
38. STEP 624
VERIFY a hi/lo chime is produced by the 2 electronic
chime modules at the FWD attendant station.
39. STEP 625
PRESS the MID call button on the Pilot Call Panel.
May 31, 2001 767-23-0164
19

### Page 22

BOEING SERVICE BULLETIN 767-23-0164
40. STEP 626
VERIFY a hi/lo chime is produced by 1 electronic
chime module at the MID attendant station.
41. STEP 627
PRESS the AFT call button on the Pilot Call Panel.
42. STEP 628
VERIFY a hi/lo chime is produced by 2 electronic
chime module at the AFT attendant station.
43. STEP 629
OPEN the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C01007 C24 INTERPHONE-CABIN SERVICE
44. STEP 630
VERIFY the attendant call lights extinguish.
45. STEP 631
CLOSE the following circuit breaker on the P11 panel:
CB NO. LOC NOMENCLATURE
------ --- ------------------------
C02007 C24 INTERPHONE-CABIN SERVICE
46. STEP 632
STOP Pilots Call Panel Test
47. STEP 700
START Audio Control/Selector Panels Test
48. STEP 701
ADJUST the four (4) flight deck Audio Control/Selector
Panels to the following configuration:
A. CAB mic selector switch depressed.
B. BOOM/OXY switch in BOOM position.
C. All on/off volume controls "OFF" except CAB, which
is to be "ON" with volume approximately midpoint.
49. STEP 702
REMOVE a FWD attendant handset from its cradle.
50. STEP 703
SPEAK into a boom microphone/headset at each audio
control/selector panel and into the FWD attendant
handset.
NOTE:
Press the audio control/selector panel PTT switch
when speaking into the boom microphone/headset.
May 31, 2001 767-23-0164
20

### Page 23

BOEING SERVICE BULLETIN 767-23-0164
51. STEP 704
VERIFY good quality 2-way voice communication between
the FWD attendant handset and the boom microphone/headsets.
52. STEP 705
STOP Audio Control/Selector Panels Test
53. STEP 800
START Pilot Handset Test
54. STEP 801
DO dial "46" on the Flight Deck Handset.
55. STEP 802
SPEAK into the Handset Microphone.
56. STEP 803
VERIFY the announcement is NOT audible over the PA
speakers.
57. STEP 804
PRESS and hold the PTT button on the Flight Deck
Handset.
58. STEP 805
VERIFY the announcement is clearly audible over the PA
speakers.
59. STEP 806
STOP Pilot Handset Test
60. STEP 900
START Handset Audio Test
61. STEP 901
VERIFY good quality 2-way voice communication between
the FWD1-L attendant handset and each of the following
handsets:
1. FWD-R Handset
2. MID-C Handset
3. AFT-L Handset
4. AFT-R Handset
NOTE:
Return the above handsets to their cradles after
verifying 2-way communication.
62. STEP 902
ENSURE all the handsets are in their cradles.
63. STEP 903
STOP Handset Audio Test
64. STEP 1000
START Attendant to PA Test
May 31, 2001 767-23-0164
21

### Page 24

BOEING SERVICE BULLETIN 767-23-0164
65. STEP 1001
ENSURE the PA system can be operated by performing the
following steps at each handset:
A. Remove the handset from cradle.
B. Dial "46" on the handset.
C. Speak into the handset.
D. Verify announcement is not heard over the PA system.
E. Push and hold the PTT button on the handset.
F. Verify announcement is clearly audible over
the PA system.
G. Replace the handset in cradle.
66. STEP 1002
VERIFY that the previous steps were performed and PASSED
for the following handsets:
1. FWD-L Handset
2. FWD-R Handset
3. MID-C Handset
4. AFT-L Handset
5. AFT-R Handset
67. STEP 1003
STOP Attendant to PA Test
68. STEP 1100
START AAU Handset Port Verification Test
69. STEP 1101
ENSURE correct handset port interface by performing the
following steps for all cabin attendant handsets:
A. Remove the handset from cradle.
B. DO dial the dial code assigned to the handsets station.
C. Verify the PINK Attnd. call lights at the handset's
station do not illuminate.
D. Replace the handset in cradle.
NOTE:
1. Assigned Dial Codes for handset locations are as follows:
FWD-L = DOOR 1 LEFT
FWD-R = DOOR 1 RIGHT
MID-C = MIDSTATION
AFT-L = DOOR 3 LEFT
AFT-R = DOOR 3 LEFT
2. Call light(s) will illuminate at the opposite station
for FWD and AFT handsets.
70. STEP 1102
VERIFY that the previous steps were performed and PASSED
for the listed handset:
1. FWD-L Handset
2. FWD-R Handset
3. MID-C Handset
4. AFT-L Handset
5. AFT-R Handset
May 31, 2001 767-23-0164
22

### Page 25

BOEING SERVICE BULLETIN 767-23-0164
71. STEP 1103
STOP AAU Handset Port Verification Test
F. Put the airplane back to a serviceable condition.
May 31, 2001 767-23-0164
23

### Page 26

BOEING SERVICE BULLETIN 767-23-0164
FIGURE TABLE OF CONTENTS
Title Page
FIGURE 1. PILOTS' HANDSET REPLACEMENT . ............................. 2 5
FIGURE 2. ATTENDANT HANDSET REPLACEMENT . . . ....................... 2 7
FIGURE 3. AUDIO ACCESSORY UNIT REPLACEMENT (AIRPLANES
VR051-VR057) ............................................... 3 0
May 31, 2001 767-23-0164
24

### Page 27

BOEING SERVICE BULLETIN 767-23-0164
CORD
PILOTS' HANDSET
1 2
3
FLIGHT COMPARTMENT
V52511
FIGURE 1. PILOTS' HANDSET REPLACEMENT
May 31, 2001 SHEET 1 OF 2 767-23-0164
25

### Page 28

BOEING SERVICE BULLETIN 767-23-0164
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
The QTY numbers shown below are the numbers of parts necessary for the airplane.
STEP TASK NAME PART NUMBER QTY NOTES
1 Remove Pilots' Handset 285W0024-4A 1 Disconnect the handset from the
cord.
2 Install Pilots' Handset 285W0024-8A 1 Connect the cord to the
handset.
3 Make Sure Dialing Codes
Marker
BAC27TEX6744 (a) 1 Is installed. If the correct
marker is not installed, replace
the existing marker with the
correct marker. Refer to
BSOPM 20-50-05.
BAC27TEX6686 (b) 1
(a) Airplanes VR051-VR057
(b) Airplane VS303
FIGURE 1. PILOTS' HANDSET REPLACEMENT
May 31, 2001 SHEET 2 OF 2 767-23-0164
26

### Page 29

BOEING SERVICE BULLETIN 767-23-0164
APPLICABLE TO AIRPLANE VS303
APPLICABLE TO AIRPLANES VR051−VR057
FWD
FWD
ASEE HANDSET
ASEE HANDSET
ASEE HANDSET
ASEE HANDSET
ASEE HANDSET
HANDSETASEEHANDSETASEE
HANDSETASEE
HANDSETASEE
HANDSETASEE
V52515
FIGURE 2. ATTENDANT HANDSET REPLACEMENT
May 31, 2001 SHEET 1 OF 3 767-23-0164
27

### Page 30

BOEING SERVICE BULLETIN 767-23-0164
CORD
A
1 2
3
V52539
FIGURE 2. ATTENDANT HANDSET REPLACEMENT
May 31, 2001 SHEET 2 OF 3 767-23-0164
28

### Page 31

BOEING SERVICE BULLETIN 767-23-0164
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
The QTY numbers shown below are the numbers of parts necessary for the airplane.
STEP TASK NAME PART NUMBER QTY NOTES
1 Remove Attendant Handset 285W0024-1L (a) 5 Disconnect the cord from the
handset.285W0024-1H (b) 5
2 Install Attendant Handset 285W0024-7L (a) 5 Connect the cord to the
handset.285W0024-7H (b) 5
3 Make Sure Dialing Codes
Marker
BAC27TEX6745 (a) 5 Is installed. If the correct
marker is not installed, replace
the existing marker with the
correct marker. Refer to
BSOPM 20-50-05.
BAC27TEX6687 (b) 5
(a) Airplanes VR051-VR057
(b) Airplane VS303
FIGURE 2. ATTENDANT HANDSET REPLACEMENT
May 31, 2001 SHEET 3 OF 3 767-23-0164
29

### Page 32

BOEING SERVICE BULLETIN 767-23-0164
21
FWD
E2−5 SHELF
MAIN EQUIPMENT CENTER
V52547
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
The QTY numbers shown below are the numbers of parts necessary for the airplane.
STEP TASK NAME PART NUMBER QTY NOTES
1 Remove Audio Accessory
Unit
285T0001-301 1 Refer to AMM 767 23-42-01/401
2 Install Audio Accessory
Unit
285T0001-302 1 Refer to AMM 767 23-42-01/401
FIGURE 3. AUDIO ACCESSORY UNIT REPLACEMENT (AIRPLANES VR051-VR057)
May 31, 2001 SHEET 1 OF 1 767-23-0164
30

### Page 33

Commercial
Airplane
Group
767
Service Bulletin
Number: 767-23-0164 Evaluation FormDate: May 31, 2001
ATA System: 2342
Prepared By: Michael Nelson
SUBJECT: COMMUNICATIONS - Interphone - Cabin Interphone System - Audio Accessory Unit And
Handset Replacement
Use this evaluation form to tell us what you think of the quality of this service bulletin. We will use the data
that you give us to improve the quality of our service bulletins.
NOTE: Please do not use this evaluation form to tell us to make changes to your manuals. To make these
changes, please use a Publication Change Request (PCR) form.
Please give us this data:
(If necessary, please use the other side. Thank you for the time you used to give us your comments.)
OPERATOR: TODAY'S DATE:
PREPARED BY: TITLE:
ORGANIZATION: TELEX CODE:
TELEPHONE NUMBER: BASE:
Please rate the quality of this service bulletin: (good) 4321 (poor)
Please rate the quality of the illustrations: (good) 4321 (poor)
Will you do the change given by this service bulletin? Yes No If not, please explain:
Is this service bulletin easy to understand? Yes No If not, please explain:
Is this service bulletin easy to use? Yes No If not, please explain:
Are the Planning Information, Material Information, and
Accomplishment Instructions accurate? Yes No If not, please explain:
Is the Manpower estimate accurate? Yes No If not, please explain:
Give the completed evaluation form to your Boeing Field Service Representative or send the evaluation form
directly to this address:
Manager
Service Bulletin Engineering
Boeing Commercial Airplane Group
P.O. Box 3707, Mail Stop 2H-37
Seattle, WA 98124-2207

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
