# Boeing Special Attention Service Bulletin 767-25-0550: Revision 2, part 3 of 3

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2024-1698; AD 2024-24-05 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 767-25-0550](https://openairdocs.org/service-documents/boeing/sb-767-25-0550.md)
- Title as filed: SB 767-25-0550 R2 (3 of 3)
- Pages: 194
- PDF: https://openairdocs.org/files/sha256/4f/e6/4fe6e1e8d6b4670ac8c005cac2dfd4f3d47564fd676114c394b1893e5eb24808
- Page: https://openairdocs.org/service-documents/boeing/sb-767-25-0550/file/4fe6e1e8d6b4

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 7, 15.
STA
544
B BEFORE  STA
522
C AFTER
STA
456
S-29L
112
S-33L
11)
3019989
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 1 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  496 of 689

### Page 2 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
654+121
STA
654+110
STA
654+88
STA
654+66
STA
654+44
STA
654+22
STA
654
STA
632
STA
588
STA
544
• S-29L
BEFORE  S-33L
3019990
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 2 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  497 of 689

### Page 3 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
654+121
STA
654+110
STA
654+88
STA
654+66
STA
654+44
STA
654+22
STA
S-29L-  654
STA
632
STA
S-33L \  610
STA
566
STA
54¿
(28)
INED LEND
AFTER
c  3019991
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 3 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  498 of 689

### Page 4 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
785.9
STA
764
STA
742
STA
698
STA
676
STA
654+121
B
S-29L
S-33L
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 4 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  499 of 689

### Page 5 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  STABILIZER
STANCHION  ANGLE
FRAME
FRAME
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
• INSULATION
DISKS  BLANKET
1 OR F
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME
DISK
STUDS OR
CLIPS, EXAMPLE
INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3019993
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 5 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  500 of 689

### Page 6 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
INSULATION
BLANKET
(40)  D
(TYPICAL PENETRATION THROUGH  EXAMPLE A  (TYPICAL PENETRATION THROUGH  EXAMPLE B
AN INSULATION BLANKET)  AN INSULATION BLANKET)
ACCESS SLIT IN  INSULATION BLANKET  ACCESS SLIT IN  INSULATION BLANKET
WIRE(S) OR
WIRE BUNDLE(S)
"SLEEVE  *SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)
EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 6 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  501 of 689

### Page 7

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
37411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-608BLANKET ASSYInstall (New)3
- 1411T4450-1548BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)4
- 1411T4450-1523BLANKET ASSYInstall (New)5
- 1411T4450-1521BLANKET ASSYInstall (New)6
- 1411T4450-825BLANKET ASSYInstall (New)7
- 1411T4450-1520BLANKET ASSYInstall (New)8
- 1411T4450-1519BLANKET ASSYInstall (New)9
- 1411T4450-610BLANKET ASSYInstall (New)10
- 1411T4450-1827BLANKET ASSYInstall (New)11
- 1411T4450-1745CAPSTRIP ASSYInstall (New)12
- 1411T4450-1744BLANKET ASSYInstall (New)13
- 1411T4450-1522BLANKET ASSYInstall (New)14
- 1411T4450-833BLANKET ASSYInstall (New)15
- 1411T4450-832BLANKET ASSYInstall (New)16
- 1411T4450-617BLANKET ASSYInstall (New)17
- 1411T4450-1823BLANKET ASSYInstall (New)18
- 1411T4450-1747BLANKET ASSYInstall (New)19
- 1411T4450-618BLANKET ASSYInstall (New)20
- 1411T4450-830BLANKET ASSYInstall (New)21
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 7 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
502 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 8

More DataQtyIdentificationNameTaskStep
- 1411T4450-829BLANKET ASSYInstall (New)22
- 1411T4450-619BLANKET ASSYInstall (New)23
- 1411T4450-836BLANKET ASSYInstall (New)24
- 1411T4450-835BLANKET ASSYInstall (New)25
- 1411T4450-620BLANKET ASSYInstall (New)26
- 1411T4450-1819BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)27
- 1411T4450-702BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)28
- 1411T4450-1826BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)29
- 1411T4450-700BLANKET ASSYInstall (New)30
- 1411T4450-699BLANKET ASSYInstall (New)31
- 1411T4450-1825BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)32
- 1411T4450-697BLANKET ASSYInstall (New)33
- 1411T4450-1252INSULATION BLAN-
KET ASSEMBLY -
SECTION 43 LOWER
LOBE
Install (New)34
- 1411T4450-629BLANKET ASSYInstall (New)35
- 1411T4450-1821BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)36
- 1411T4450-631BLANKET ASSYInstall (New)37
- 1411T4450-1832BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)38
- 1411T4450-633BLANKET ASSYInstall (New)39
(b)(c)(h)--PENETRATION AND
SLEEVE
Make40
(d) --SLEEVEFill
(e)(f) --SLEEVEClose
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 8 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
503 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 9

More DataQtyIdentificationNameTaskStep
(g) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)41
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(c) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(d) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(e) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(f) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(g) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(h) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 9 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
504 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 10

More DataQtyIdentificationName
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 73: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 10 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
505 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 11 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
• This Figure applies only to: Group 7, 12-15, 18.
STA
654+121
STA
654+88
STA  STA
654+44  654+110
STA  STA
654  654+66
STA  STA
610  654+22
STA
632
-S-29R
STA  A'B  S-33A
456
STA
478
STA
434
3019995
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 1 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  506 of 689

### Page 12

FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 2 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
507 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 13 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  STABILIZER
STANCHION  ANGLE
FRAME
FRAME
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
• INSULATION
DISKS  BLANKET
• OR D
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME
DISK
STUDS OR
_CLIPS, EXAMPLE
INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3019997
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 3 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  508 of 689

### Page 14 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
D
INSULATION
BLANKET
20
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
C
ACCESS SLIT IN  ACCESS SLIT IN
INSULATION BLANKET  INSULATION BLANKET
WIRE(S) OR
WIRE BUNDLE(S)
SLEEVE  'SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)  EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 4 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  509 of 689

### Page 15

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
17411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-672BLANKET ASSYInstall (New)3
- 1411T4450-1818BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)4
- 1411T4450-1351BLANKET ASSYInstall (New)5
- 1411T4450-652BLANKET ASSYInstall (New)6
- 1411T4450-826BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)7
- 1411T4450-685BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)8
- 1411T4450-686BLANKET ASSYInstall (New)9
- 1411T4450-687BLANKET ASSYInstall (New)10
- 1411T4450-688BLANKET ASSYInstall (New)11
- 1411T4450-689BLANKET ASSYInstall (New)12
- 1411T4450-690BLANKET ASSYInstall (New)13
- 1411T4450-1361BLANKET ASSYInstall (New)14
- 1411T4450-1362BLANKET ASSYInstall (New)15
- 1411T4450-1363BLANKET ASSYInstall (New)16
- 1411T4450-1364BLANKET ASSYInstall (New)17
- 1411T4450-1365BLANKET ASSYInstall (New)18
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 5 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
510 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 16

More DataQtyIdentificationNameTaskStep
- 1411T4450-1366BLANKET ASSYInstall (New)19
(b)(c)(h)--PENETRATION AND
SLEEVE
Make20
(d) --SLEEVEFill
(e)(f) --SLEEVEClose
(g) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)21
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(c) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(d) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(e) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(f) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(g) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(h) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
511 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 17

The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 74: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
512 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 18 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 7, 11-12.
STA
1197
STA
1175
STA
1153
STA
1131
D  STA
1109
S-29L
STA  STA
1197  1065
+88  STA
1197
S-33L
+66
STA
1197
+44
STA
1197
+22
STA
1197
→ S-29L
→S-33L
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 1 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  513 of 689

### Page 19 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
1263
STA
1241
STA
1219
STA
1197+132
STA
1197+110
STA
1197+88
• S-29L
* S-33L
/NED END
3020000
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 2 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  514 of 689

### Page 20 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
1417
STA
1395
STA
1373
STA
1351
STA
1329
1 30
STA
1307
STA
1285
1131  S-29L
129
116
S-33L
3020007
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 3 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  515 of 689

### Page 21 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  STABILIZER
STANCHION  ANGLE
FRAME
FRAME
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
• INSULATION
DISKS  BLANKET
1 OR F
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME •
DISK
STUDS OR
•CLIPS, EXAMPLE
INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3020008
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 4 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  516 of 689

### Page 22 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
INSULATION
BLANKET
(36  D
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
E
ACCESS SLIT IN  ACCESS SLIT IN
INSULATION BLANKET  INSULATION BLANKET
WIRE(S) OR
WIRE BUNDLE(S)
*SLEEVE  "SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)  EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D  3020009
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 5 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  517 of 689

### Page 23

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
37411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-892BLANKET ASSYInstall (New)3
- 1411T4450-893BLANKET ASSYInstall (New)4
- 1411T4450-894BLANKET ASSYInstall (New)5
- 1411T4450-895BLANKET ASSYInstall (New)6
- 1411T4450-896BLANKET ASSYInstall (New)7
- 1411T4450-897BLANKET ASSYInstall (New)8
- 1411T4450-1461BLANKET ASSYInstall (New)9
- 1411T4450-1462BLANKET ASSYInstall (New)10
- 1411T4450-1463BLANKET ASSYInstall (New)11
- 1411T4450-1464BLANKET ASSYInstall (New)12
- 1411T4450-1465BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)13
- 1411T4450-1466BLANKET ASSYInstall (New)14
- 1411T4450-1523BLANKET ASSYInstall (New)15
- 4411T4450-835BLANKET ASSYInstall (New)16
- 1411T4450-1376BLANKET ASSYInstall (New)17
- 1411T4450-1574BLANKET ASSYInstall (New)18
- 1411T4450-1547BLANKET ASSYInstall (New)19
- 1411T4450-898BLANKET ASSYInstall (New)20
- 2411T4450-1575BLANKET ASSYInstall (New)21
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 6 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
518 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 24

More DataQtyIdentificationNameTaskStep
- 1411T4450-1372BLANKET ASSYInstall (New)22
- 1411T4450-1523BLANKET ASSYInstall (New)23
- 1411T4450-1373BLANKET ASSYInstall (New)24
- 1411T4450-1576BLANKET ASSYInstall (New)25
- 1411T4450-1572BLANKET ASSYInstall (New)26
- 1411T4450-1374BLANKET ASSYInstall (New)27
- 1411T4450-1577BLANKET ASSYInstall (New)28
- 1411T4450-1573BLANKET ASSYInstall (New)29
- 1411T4450-1375BLANKET ASSYInstall (New)30
- 1411T4450-1578BLANKET ASSYInstall (New)31
- 1411T4450-1376BLANKET ASSYInstall (New)32
- 1411T4450-1377BLANKET ASSEMBLY
- INUSLATION
FREIGHTER
Install (New)33
- 1411T4450-1378BLANKET ASSYInstall (New)34
- 1411T4450-1417BLANKET ASSYInstall (New)35
(b)(c)(h)--PENETRATION AND
SLEEVE
Make36
(d) --SLEEVEFill
(e)(f) --SLEEVEClose
(g) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)37
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(c) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
519 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 25

More DataQtyIdentificationNameTaskStep
(d) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(e) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(f) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(g) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(h) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 75: AFT CARGO COMPARTMENT, SECTION 46, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
520 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 26 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 7, 11-12.
+44
STAS
STA
1109
STA
1087
STA
1065
S-29R
S-33R
3020010
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 1 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  521 of 689

### Page 27

FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 2 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
522 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 28

FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 3 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
523 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 29 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  STABILIZER
STANCHION  ANGLE
FRAME
FRAME
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
• INSULATION
DISKS  BLANKET
OR E
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME -
DISK
CLIPS, EXAMPLE  STUDS OR
INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3020014
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 4 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  524 of 689

### Page 30 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
INSULATION
BLANKET
19)
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
ACCESS SLIT IN  ACCESS SLIT IN
INSULATION BLANKET  INSULATION BLANKET
WIRE(S) OR
WIRE BUNDLE(S)
"SLEEVE  *SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)  EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D  3020015
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 5 OF 8)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  525 of 689

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
18411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-847BLANKET ASSYInstall (New)3
- 1411T4450-848BLANKET ASSYInstall (New)4
- 1411T4450-849BLANKET ASSYInstall (New)5
- 1411T4450-850BLANKET ASSYInstall (New)6
- 1411T4450-851BLANKET ASSYInstall (New)7
- 1411T4450-854BLANKET ASSYInstall (New)8
- 1411T4450-1443BLANKET ASSYInstall (New)9
- 1411T4450-1444BLANKET ASSYInstall (New)10
- 1411T4450-1445BLANKET ASSYInstall (New)11
- 1411T4450-1446BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)12
- 1411T4450-1447BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)13
- 1411T4450-1448BLANKET ASSYInstall (New)14
- 1411T4450-861BLANKET ASSYInstall (New)15
- 1411T4450-1596CAPSTRIP ASSYInstall (New)16
- 1411T4450-862BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)17
- 1411T4450-863BLANKET ASSYInstall (New)18
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 6 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
526 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 32

More DataQtyIdentificationNameTaskStep
(b)(c)(h)--PENETRATION AND
SLEEVE
Make19
(d) --SLEEVEFill
(e)(f) --SLEEVEClose
(g) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)20
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(c) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(d) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(e) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(f) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(g) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(h) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 7 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
527 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 33

The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 76: AFT CARGO COMPARTMENT, SECTION 46, RIGHT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 8 OF 8)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
528 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 34 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 11-12.
→ STA  544
STA
522
B  BEFORE
AFTER  SIA
478
S-29L
1 12
S-33L.
3020016
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 1 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  529 of 689

### Page 35

FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 2 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
530 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 36

FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 3 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
531 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 37 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
785.9
STA
764
STA
742
STA
698
STA
676
STA
654+121
B
*S-29L
S-33L
BO LEND
3020020
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 4 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  532 of 689

### Page 38 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  BL  STABILIZER
STANCHION-  ANGLE
FRAME
FRAME-
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
INSULATION
DISKS  BLANKET
OR F
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME ~
DISK
STUDS OR
CLIPS, EXAMPLE
- INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3020022
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 5 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  533 of 689

### Page 39 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
INSULATION
BLANKET
40)
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
F
ACCESS SLIT IN
INSULATION BLANKET  ACCESS SLIT IN  INSULATION BLANKET
• WIRE(S) OR
WIRE BUNDLE(S)
"SLEEVE  SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)  EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D  3020023
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 6 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  534 of 689

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
37411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-608BLANKET ASSYInstall (New)3
- 1411T4450-1548BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)4
- 1411T4450-1523BLANKET ASSYInstall (New)5
- 1411T4450-1521BLANKET ASSYInstall (New)6
- 1411T4450-825BLANKET ASSYInstall (New)7
- 1411T4450-1520BLANKET ASSYInstall (New)8
- 1411T4450-1519BLANKET ASSYInstall (New)9
- 1411T4450-610BLANKET ASSYInstall (New)10
- 1411T4450-1518BLANKET ASSYInstall (New)11
- 1411T4450-1517BLANKET ASSYInstall (New)12
- 1411T4450-611BLANKET ASSYInstall (New)13
- 1411T4450-1522BLANKET ASSYInstall (New)14
- 1411T4450-833BLANKET ASSYInstall (New)15
- 1411T4450-832BLANKET ASSYInstall (New)16
- 1411T4450-617BLANKET ASSYInstall (New)17
- 1411T4450-828BLANKET ASSYInstall (New)18
- 1411T4450-827BLANKET ASSYInstall (New)19
- 1411T4450-618BLANKET ASSYInstall (New)20
- 1411T4450-830BLANKET ASSYInstall (New)21
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 7 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
535 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 41

More DataQtyIdentificationNameTaskStep
- 1411T4450-829BLANKET ASSYInstall (New)22
- 1411T4450-619BLANKET ASSYInstall (New)23
- 1411T4450-836BLANKET ASSYInstall (New)24
- 1411T4450-835BLANKET ASSYInstall (New)25
- 1411T4450-620BLANKET ASSYInstall (New)26
- 1411T4450-621BLANKET ASSYInstall (New)27
- 1411T4450-702BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)28
- 1411T4450-701BLANKET ASSYInstall (New)29
- 1411T4450-700BLANKET ASSYInstall (New)30
- 1411T4450-699BLANKET ASSYInstall (New)31
- 1411T4450-698BLANKET ASSYInstall (New)32
- 1411T4450-697BLANKET ASSYInstall (New)33
(b) 1411T4450-628BLANKET ASSYInstall (New)34
- 1411T4450-629BLANKET ASSYInstall (New)35
- 1411T4450-630BLANKET ASSYInstall (New)36
- 1411T4450-631BLANKET ASSYInstall (New)37
- 1411T4450-632BLANKET ASSYInstall (New)38
- 1411T4450-633BLANKET ASSYInstall (New)39
(c)(d)(i)--PENETRATION AND
SLEEVE
Make40
(e) --SLEEVEFill
(f)(g) --SLEEVEClose
(h) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)41
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) 411T4450-1252 is acceptable as an alternate part number.
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 8 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
536 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 42

More DataQtyIdentificationNameTaskStep
(c) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(d) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(e) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(f) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(g) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(h) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(i) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 9 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
537 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 43

More DataQtyIdentificationName
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 77: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 10 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
538 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 44 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 11.
STA
654+121
STA
654+88
STA  STA
654+44  654+110
STA  STA
654  654+66
STA  STA
610  654+22
STA
632
S-29R
B
STA  A'B  S-33R
456
STA
478
STA
434
3020024
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 1 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  539 of 689

### Page 45

FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 2 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
540 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 46 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  BL  STABILIZER
STANCHION-  ANGLE
FRAME
FRAME-
SIDEWALL
BLANKET  INSULATION  LINING  EXAMPLE  STUDS OR CLIPS,
INSULATION
BLANKET
INSULATION
DISKS  BLANKET
OR D
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME ~
DISK
STUDS OR
CLIPS, EXAMPLE
- INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3020027
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 3 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  541 of 689

### Page 47 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
D
INSULATION
BLANKET
20
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
ACCESS SLIT IN  ACCESS SLIT IN
INSULATION BLANKET  INSULATION BLANKET
WIRE SUNBLE(S)
SLEEVE  SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)  EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D  3020028
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 4 OF 7)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  542 of 689

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
17411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-672BLANKET ASSYInstall (New)3
(b) 1411T4450-859BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)4
- 1411T4450-1351BLANKET ASSYInstall (New)5
- 1411T4450-652BLANKET ASSYInstall (New)6
- 1411T4450-826BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)7
- 1411T4450-685BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)8
- 1411T4450-686BLANKET ASSYInstall (New)9
- 1411T4450-687BLANKET ASSYInstall (New)10
- 1411T4450-688BLANKET ASSYInstall (New)11
- 1411T4450-689BLANKET ASSYInstall (New)12
- 1411T4450-690BLANKET ASSYInstall (New)13
- 1411T4450-1361BLANKET ASSYInstall (New)14
- 1411T4450-1362BLANKET ASSYInstall (New)15
- 1411T4450-1363BLANKET ASSYInstall (New)16
- 1411T4450-1364BLANKET ASSYInstall (New)17
- 1411T4450-1365BLANKET ASSYInstall (New)18
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 5 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
543 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 49

More DataQtyIdentificationNameTaskStep
- 1411T4450-1366BLANKET ASSYInstall (New)19
(c)(d)(i)--PENETRATION AND
SLEEVE
Make20
(e) --SLEEVEFill
(f)(g) --SLEEVEClose
(h) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)21
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) 411T4450-1818 is acceptable as an alternate part number.
(c) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(d) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(e) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(f) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(g) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(h) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(i) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 6 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
544 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 50

The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 78: FORWARD CARGO COMPARTMENT, SECTION 43, RIGHT SIDE - INSULATION BLANKETS
- REPLACEMENT
(SHEET 7 OF 7)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
545 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 51 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
This Figure applies only to: Group 13, 18.
STA
544
STA
522
B BEFORE
C AFTER
S-29L-
112
S-33L
3020029
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 1 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  546 of 689

### Page 52

FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 2 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
547 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 53 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
654+121
STA
654+110
STA
654+88
STA
654+66
STA
654+44
STA
654+22
STA
S-29L-  654
31)  STA
632
STA
S-33L ~  610
AFTER  20
3020033
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 3 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  548 of 689

### Page 54 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
STA
785.9
STA
764
STA
742
STA
698
STA
676
STA
654+121
B
S-29L
S-33L
3020034
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 4 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  549 of 689

### Page 55 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
67.5  STABILIZER
STANCHION  ANGLE
FRAME
FRAME
SIDEWALL
BLANKET  INSULATION  LINING  STUDS OR CLIPS,  EXAMPLE
INSULATION
BLANKET
• INSULATION
DISKS  BLANKET
1 OR F
STRINGER  TYPICAL OVERLAP OF ADJACENT INSULATION
S-29  BLANKETS AT A TYPICAL FRAME
B-B
TYPICAL
A-A
FRAME
DISK
STUDS OR
CLIPS, EXAMPLE
INSULATION
BLANKET
TYPICAL OVERLAP OF ONE INSULATION
BLANKET AT A TYPICAL FRAME
C-C  3020035
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 5 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  767-25-0550
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details  550 of 689

### Page 56 (OCR)

BOEING SERVICE BULLETIN 767-25-0550
INSULATION
BLANKET
INSULATION
BLANKET
38) D
EXAMPLE A  EXAMPLE B
(TYPICAL PENETRATION THROUGH  (TYPICAL PENETRATION THROUGH
AN INSULATION BLANKET)  AN INSULATION BLANKET)
ACCESS SLIT IN  INSULATION BLANKET  ACCESS SLIT IN  INSULATION BLANKET
(39)
WIRE(S) OR
WIRE BUNDLE(S)
SLEEVE
SLEEVE
SYSTEM
RUN(S)
EXAMPLE WITH WIRE(S) OR WIRE BUNDLE(S)
EXAMPLE WITH SYSTEM RUN(S)
D-D  D-D  3020036
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 6 OF 10)
Original Issue: January 30, 2015
Revision 2 December 18, 2023  Export Controlled ECCN: 9E991  767-25-0550
BOEING PROPRIETARY - See page 1 for details  551 of 689

### Page 57

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
Insulation blankets
with one or more of
these part numbers
could be installed.
37411T4011-( ),
411T4110-( ),
411T4440-( ),
411T4460-( )
BLANKET ASSYRemove1
Clean the surface to
which the hook fas-
tener tape is to be
applied.
--SURFACEClean2
(a) -BMS 8-372, TYPE IHOOK FASTENER
TAPE
Install (New)
(a) -BMS 8-372, TYPE ILOOP FASTENER
TAPE
Install (New)
- 1411T4450-608BLANKET ASSYInstall (New)3
- 1411T4450-1751BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)4
- 1411T4450-1523BLANKET ASSYInstall (New)5
- 1411T4450-1521BLANKET ASSYInstall (New)6
- 1411T4450-825BLANKET ASSYInstall (New)7
- 1411T4450-1520BLANKET ASSYInstall (New)8
- 1411T4450-1519BLANKET ASSYInstall (New)9
- 1411T4450-610BLANKET ASSYInstall (New)10
- 1411T4450-1827BLANKET ASSYInstall (New)11
- 1411T4450-1745CAPSTRIP ASSYInstall (New)12
- 1411T4450-1744BLANKET ASSYInstall (New)13
- 1411T4450-1522BLANKET ASSYInstall (New)14
- 1411T4450-833BLANKET ASSYInstall (New)15
- 1411T4450-832BLANKET ASSYInstall (New)16
- 1411T4450-617BLANKET ASSYInstall (New)17
- 1411T4450-1823BLANKET ASSYInstall (New)18
- 2411T4450-1747BLANKET ASSYInstall (New)19
- 2411T4450-1854BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)20
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 7 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
552 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 58

More DataQtyIdentificationNameTaskStep
- 1411T4450-1855BLANKET ASSYInstall (New)21
- 1411T4450-836BLANKET ASSYInstall (New)22
- 1411T4450-835BLANKET ASSYInstall (New)23
- 1411T4450-620BLANKET ASSYInstall (New)24
- 1411T4450-1819BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)25
- 1411T4450-702BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)26
- 1411T4450-1826BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)27
- 1411T4450-700BLANKET ASSYInstall (New)28
- 1411T4450-699BLANKET ASSYInstall (New)29
- 1411T4450-1825BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)30
- 1411T4450-697BLANKET ASSYInstall (New)31
- 1411T4450-628BLANKET ASSYInstall (New)32
- 1411T4450-629BLANKET ASSYInstall (New)33
- 1411T4450-1821BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)34
- 1411T4450-631BLANKET ASSYInstall (New)35
- 1411T4450-1832BLANKET ASSEMBLY
- INSULATION
FREIGHTER
Install (New)36
- 1411T4450-633BLANKET ASSYInstall (New)37
(b)(c)(h)--PENETRATION AND
SLEEVE
Make38
(d) --SLEEVEFill
(e)(f) --SLEEVEClose
(g) -BMS 5-157, TYPE 1,
CLASS 1 GRADE A
OR B, FORM 1, COMP.
MPVF
INSULATION BLAN-
KET TAPE
Install (New)39
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 8 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
553 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 59

More DataQtyIdentificationNameTaskStep
(a) Install length(s) of hook fastener tape to agree with the length(s) of loop fastener tape on each new insu-
lation blanket to hold the insulation blanket to the structure or to hold an insulation blanket to another in-
sulation blanket. It could also be necessary to install length(s) of loop tape on blanket(s) to engage with
hook tape that is on the structure or that is on adjacent blanket(s).
(b) A penetration in an insulation blanket is necessary to let bracket(s), system run(s), wire(s) or wire bundle(s)
route through the insulation blanket. Some new insulation blankets are supplied with one or more pene-
trations and sleeves as part of their design, as shown by Example B. If an insulation blanket is supplied
with one or more penetrations and sleeves, but one or more of them do not align with the route of a
bracket, system run, wire or wire bundle that must go through the insulation blanket, the insulation blanket
must be changed to add one or more new penetrations and sleeves ('Example A' or 'Example B') at the
necessary location(s). Refer to APPENDIX P.
(c) Apply the service bulletin number, 767-25-0550 R02, to the insulation blanket to show that it is changed.
(d) Fill all of the space in the sleeve with foam BMS 1-68, GRADE A, FORM II to make sure there is a fire
extinguishing barrier that continues the properties of the fire stop blanket.
(e) Close the end of the sleeve around the system run(s), wire(s) or wire bundle(s) with lacing tape, BMS 13-
54, GRADE D, TYPE III, CLASS 1, FINISH C, then apply insulation blanket tape, BMS 5-157, TYPE 1,
CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF, on the tied lacing tape.
(f) For any penetrations and sleeves that have system run(s), wire(s) or wire bundle(s) through them:
– Any sleeve that is not used or not required can be cut off and have BMS 5-157, TYPE 1, CLASS 1
GRADE A OR B, FORM 1, COMPOSITION MPVF insulation blanket tape put on the insulation
blanket to close the penetration(s).
– Any sleeve with multiple wires or systems in the penetration, must have all of the space(s) in the
sleeve(s) filled with BMS 1-68, GRADE A, FORM II, and each end tightly tied with BMS 13-54, GRADE
D, TYPE III, CLASS 1, FINISH C lacing tape with BMS 5-157, TYPE 1, CLASS 1 GRADE A OR B,
FORM 1, COMPOSITION MPVF insulation blanket tape put on the tied lacing tape.
(g) Put the edges of an insulation blanket access slit together and apply insulation blanket tape BMS 5-157,
TYPE 1, CLASS 1 GRADE A OR B, FORM 1, COMPOSITION MPVF on the access slit to close it.
(h) If an insulation blanket is supplied without one or more required penetrations or sleeves, the supplied in-
sulation blanket can be changed to add one or more new penetrations and sleeves ('Example A' or 'Ex-
ample B') at the necessary location(s). Refer to APPENDIX P.
The parts shown in the table below are provided as extra parts for this figure.
More DataQtyIdentificationName
(a)(b)(d)3OP1913-1STUD - INSULATION
ATTACH
(a)(b)(d)3OP1913-2STUD - INSULATION
ATTACH
(a)(d)2BACC15AP2CLIP, RETAINING
(a)(c)10BACS31N1HDISK
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 9 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
554 of 689
BOEING SERVICE BULLETIN 767-25-0550

### Page 60

More DataQtyIdentificationName
(a) Insulation blanket attachment parts can be used to replace attachment parts identified
as missing during or after insulation blanket removal.
(b) Bond with BMS 5-45 Class B or BMS 5-44 Class B (BMS 5-95 Class B optional). Do not
remove sealant squeeze-out that comes through the holes in the base of a stud.
(c) This part can also be bonded with a sealant given in footnote (b).
(d) The plastic pin of a stud or clip can be cut to prevent interference with structure or adjacent
systems, but a minimum of two 'threads' must show on the end of the pin after the retainer
disk is installed.
FIGURE 79: FORWARD CARGO COMPARTMENT, SECTION 43, LEFT SIDE - INSULATION BLANKETS -
REPLACEMENT
(SHEET 10 OF 10)
Export Controlled ECCN: 9E991
BOEING PROPRIETARY - See page 1 for details
Original Issue: January 30, 2015
767-25-0550Revision 2 December 18, 2023
555 of 689
BOEING SERVICE BULLETIN 767-25-0550

The text continues at https://openairdocs.org/service-documents/boeing/sb-767-25-0550/file/4fe6e1e8d6b4.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
