# Boeing Special Attention Service Bulletin 767-25-0589: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2022-1304, the docket of AD 2023-12-23. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 767-25-0589](https://openairdocs.org/service-documents/boeing/sb-767-25-0589.md)
- Title as filed: RB-767-25-0589-00
- Pages: 13
- PDF: https://openairdocs.org/files/sha256/ce/b5/ceb5dce3146eb71f677d5b33e4501d918c7fc8542c721ab87d02fe19858e4e24
- Page: https://openairdocs.org/service-documents/boeing/sb-767-25-0589/file/ceb5dce3146e

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
767
Requirements Bulletin
SPECIAL ATTENTION
Number: 767-25-0589 RB
Original Issue: February 25, 2022
ATA System: 2510 1131
SUBJECT: EQUIPMENT/FURNISHINGS - Flight Compartment - First Observer Seat Positions
Marker Installation
EXPORT CONTROLLED - This technology or software is subject to the U.S. Export Administration Regulations
(EAR), (15 C.F.R. Parts 730-774). No authorization from the U.S. Department of Commerce is required for
export, re-export, in-country transfer, or access EXCEPT to country group E:1 or E:2 countries/persons per
Supp.1 to Part 740 of the EAR.
9E991ECCN:
Copyright © 2022 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: February 25, 2022
767-25-0589 RB
1 of 13
2.0

### Page 2

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
2 of 13
REQUIREMENTS BULLETIN 767-25-0589
BLANK PAGE

### Page 3

Table of Contents
1. EFFECTIVITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A. Airplanes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B. Spares Affected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. CONCURRENT REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. APPROVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5. ACCOMPLISHMENT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
A. General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. Work Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FIGURE 1: FLIGHT DECK - MARKERS FOR FIRST OBSERVER SEAT INSTALLATION . . . . . . . 10
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
3 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 4

Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
4 of 13
REQUIREMENTS BULLETIN 767-25-0589
BLANK PAGE

### Page 5

Commercial 
Airplanes
767
Requirements Bulletin
SPECIAL ATTENTION
Number: 767-25-0589 RB
Original Issue: February 25, 2022
ATA System: 2510 1131
SUBJECT: EQUIPMENT/FURNISHINGS - Flight Compartment - First Observer Seat Positions
Marker Installation
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS DOCUMENT IMMEDIATELY. THIS IS
AN ENHANCED REQUIRED FOR COMPLIANCE DOCUMENT. THE BOEING PROCESSES USED TO CREATE
THE SERVICE BULLETIN (SB) AND THE REQUIREMENTS BULLETIN (RB) ENSURE THAT THE
INFORMATION BETWEEN "RC START" AND "RC END" IN THE SB ARE IDENTICAL TO THE INFORMATION
IN THE SAME SECTIONS (COMPLIANCE, WORK INSTRUCTIONS…) OF THE RB WHICH THE SB REFERS
TO AS THE RELATED DOCUMENT.
1. Effectivity
A. Airplanes
This bulletin is applicable to 767-300F Airplane(s), line number(s) 580, 590, 594, 598, 600, 616,
622, 624, 626, 628, 630, 632, 634, 636, 638, 640, 660, 666, 670, 672, 674, 678, 682, 712, 724,
726, 728, 730, 732, 756, 760, 764, 778, 806, 846, 848, 854, 858, 860, 885, 934, 936-937, 939,
947-948, 956, 959-960, 979, 983, 986, 988-989, 991-992, 1002-1003, 1005-1006, 1008, 1020,
1022, 1024-1026, 1028, 1035, 1044, 1046, 1048, 1051, 1053, 1056-1059, 1061, 1063-1064,
1070-1090, 1093-1097, 1099, 1101, 1103, 1105-1106, 1108, 1110, 1112, 1115, 1118, 1121, 1123,
1125, 1127, 1130, 1133, 1136, 1138, 1140-1142, 1144, 1146, 1148, 1150, 1152-1153, 1155, 1157,
1159, 1161, 1163, 1165, 1167, 1169, 1171, 1173, 1175, 1177, 1179-1180, 1182-1183, 1185-1187,
1189-1191, 1193-1195, 1197-1199, 1201, 1203-1204, 1206 in 2 Group(s). Where the effectivity
is presented with hyphens between line numbers, the airplane applicability means "through" and
"inclusive", e.g. line numbers 1-9 means line numbers 1 through 9 inclusive.
The Variable Numbers and Group Information for the applicable airplanes is given below.
DESCRIPTIONCONFIGURATIONGROUP
767-300F Airplanes that do not have an Emergency Locator
Transmitter (ELT) on the aft side of the P61 panel in the flight
compartment.
-1
767-300F Airplanes that have an ELT on the aft side of the P61 panel
in the flight compartment.
-2
Airplane Models:
767-300F
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
5 of 13

### Page 6

GroupVariable Number
1VR201 - VR211
1VR251
1VR256 - VR259
2VR260
GroupVariable Number
1VR266 - VR298
2VT501
1VT511 - VT513
2VT521 - VT523
GroupVariable Number
1VT531 - VT533
1VT556 - VT638
1VW701 - VW721
1VW851
B. Spares Affected
None.
2. CONCURRENT REQUIREMENTS
None.
3. COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
Requirements Bulletin 767-25-0589 RB. The Airworthiness Directive will make the compliance tasks and
times given in Requirements Bulletin 767-25-0589 RB mandatory.
When more than one OPTION is given for a CONDITION, do only one of the OPTION numbers. When
more than one ACTION is given for a CONDITION or an OPTION, do all of the ACTION numbers for
thatCONDITION or OPTION
Table 1: FLIGHT DECK - FIRST OBSERVER SEAT MARKERS INSTALLATION
Repeat Interval
(Not to Exceed)
Boeing Recommended
Compliance Time
ActionCondition
-Within 12 months after
the Original Issue date of
Requirements Bulletin
767-25-0589 RB.
ACTION 1: Install marker,
part number
BAC27TFDE714, in the
flight deck.
All Airplanes
ACTION 2: Install marker,
part number
BAC27TFDE715, in the
flight deck (2 locations).
4. APPROVAL
This Requirements Bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this document comply with the applicable regulations and are FAA approved, as well as European
Union Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in this Requirements Bulletin effectivity. This document and its approval were based on the
airplane in its original Boeing delivery configuration or as modified by other Boeing changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected by
this Requirements Bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this Requirements Bulletin.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
6 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 7

5.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
NOTE: 1. This is an Enhanced Required for Compliance document. There will be a separate
Service Bulletin (SB) and a separate Requirements Bulletin (RB). If an RB is mandated
by an Airworthiness Directive (AD), then all applicable requirements specified in the
RB must be done. For the related SB, some locations are marked RC Start and RC
End to identify the requirements that are restated from the RB. For the related SB,
the areas between RC Start and RC End, including sub-steps and any figures
identified between RC Start and RC End, must be done to comply with the AD.
Therefore, an Alternative Method of Compliance (AMOC) is required for any deviations
to steps between RC Start and RC End, including substeps and identified figures.
For the related SB, the steps not between RC Start and RC End may be deviated
from using accepted methods in accordance with the operator's maintenance or
inspection program without obtaining approval of an AMOC; this is provided that the
steps between RC Start and RC End, including sub-steps and identified figures, can
still be done as specified, and the airplane can be put back in an airworthy condition.
Figures not required for compliance are omitted from the RB.
2. This is an Enhanced Required for Compliance document. The Boeing processes
used to create the Service Bulletin (SB) and the Requirements Bulletin (RB) ensure
that the information between "RC Start" and "RC End" in the SB are identical to the
information in the same sections (Compliance, Work Instructions...) of the RB which
the SB refers to as the related document.
3. The compliance times for the actions in WORK INSTRUCTIONS are in Compliance.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque Values:
— Non-standard torque values for maintenance tasks are included in the
applicable installation step.
5. When more than one OPTION is given for a CONDITION, do only one of the OPTION
numbers. When more than one ACTION is given for a CONDITION or an OPTION,
do all of the ACTION numbers for thatCONDITION or OPTION.
6. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
7 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 8

7. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
B. WORK INSTRUCTIONS
Actions Required for Compliance
1. Requirements
Group 1:
TABLE 1: FLIGHT DECK - FIRST OBSERVER SEAT MARKERS INSTALLATION
Refer to the listed proce-
dures in SB 767-25-0589
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 1 - OPEN ACCESS--All Airplanes
-FIGURE 1ACTION 1: Install marker,
part number
BAC27TFDE714, in the
flight deck.
ACTION 2: Install marker,
part number
BAC27TFDE715, in the
flight deck (2 locations).
PART 4 - CLOSE AC-
CESS
--
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
8 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 9

Group 2:
TABLE 2: FLIGHT DECK - FIRST OBSERVER SEAT MARKERS INSTALLATION
Refer to the listed proce-
dures in SB 767-25-0589
Original Issue or later
approved revisions as an
accepted procedure
Method of ComplianceActionCondition
PART 1 - OPEN ACCESS--All Airplanes
PART 2 - SPACING--
-FIGURE 1ACTION 1: Install marker,
part number
BAC27TFDE714, in the
flight deck.
ACTION 2: Install marker,
part number
BAC27TFDE715, in the
flight deck (2 locations).
PART 3 - ELT MARKER
INSTALLATION
--
PART 4 - CLOSE AC-
CESS
--
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
9 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 10 (OCR)

REQUIREMENTS BULLETIN 767-25-0589
FWD
FLIGHT COMPARTMENT
(TYPICAL)
CLOSURE
ASSEMBLY
0.75
STA  0.25
190
0.75
0.25  FWD  2976092
FIGURE 1: FLIGHT DECK - MARKERS FOR FIRST OBSERVER SEAT INSTALLATION
(SHEET 1 OF 4)
Original Issue: February 25, 2022
Export Controlled ECCN: 9E991  767-25-0589 RB
Copyright © Unpublished Work - See page 1 for details.  10 of 13

### Page 11

FIGURE 1: FLIGHT DECK - MARKERS FOR FIRST OBSERVER SEAT INSTALLATION
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
11 of 13
REQUIREMENTS BULLETIN 767-25-0589

### Page 12 (OCR)

REQUIREMENTS BULLETIN 767-25-0589
LIFE JACKETS -
STOWAGE
TYPICAL
STA
245
CENTERLINE
- OF MARKERS
• MARKERS
SIDEWALL
LINING
A-A  ND  2976878
FIGURE 1: FLIGHT DECK - MARKERS FOR FIRST OBSERVER SEAT INSTALLATION
(SHEET 3 OF 4)
Original Issue: February 25, 2022
767-25-0589 RB
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.  12 of 13

### Page 13

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each airplane.
More DataQtyIdentificationNameTaskStep
(b)1BAC27TFDE714MARKER - OBSERV-
ER SEAT
Install (New)1
(a)(b)1BAC27TFDE715MARKER - OBSERV-
ER SEAT
Install (New)2
(a)(b)1BAC27TFDE715MARKER - OBSERV-
ER SEAT
Install (New)3
(a) Make sure the new marker does not overlap with the installed markers.
(b) Refer to SOPM 20-50-05, Type P, as an accepted procedure.
FIGURE 1: FLIGHT DECK - MARKERS FOR FIRST OBSERVER SEAT INSTALLATION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 25, 2022
767-25-0589 RB
13 of 13
REQUIREMENTS BULLETIN 767-25-0589

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
