# Boeing Service Bulletin 777-23-0010: No revision named

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2011-0034, the docket of a proposed AD (Federal Register 2011-2172, 2013-09422). Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Service Bulletin 777-23-0010](https://openairdocs.org/service-documents/boeing/sb-777-23-0010.md)
- Title as filed: U.S. DOT/FAA - Service Bulletin
- Pages: 33
- PDF: https://openairdocs.org/files/sha256/4b/26/4b26d94a49cb117406941f4d0b1fa72f254a4d3325a5001a2a1656612218eb14
- Page: https://openairdocs.org/service-documents/boeing/sb-777-23-0010/file/4b26d94a49cb

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial
Airplane
Group
777
Service Bulletin
Number: 777-23-0010 SummaryDate: April 25, 1996
ATA System: 2339
SUBJECT: COMMUNICATIONS - CABIN MANAGEMENT SYSTEM - SOFTWARE CHANGE
BACKGROUND
This change will make the cabin management
system (CMS) operate with less problems.
This change will make sure that passenger address
(PA) announcements can be heard. The installed
speaker drive module (SDM) software can cause
some PA announcements to not be heard. The
SDM will turn off the digital sound receivers if a
chime occurs. The announcement has to be made
again after the chime stops. The installed seat
electronics unit (SEU) software can also cause
some PA announcements to not be heard. The
SEU can cause damage to some PA signals to the
passenger control units (PCU). The PCU can
accept the damaged digital signal as a different
signal or reject the signal. The new SDM and SEU
software will prevent these problems. New speaker
volume adjustments are available in the new
configuration data base (CDB). The optional volume
adjustments will increase the PA announcement
volume for the cabin attendants.
This change will make sure all the passenger cabin
functions of the CMS operate. One operator told
Boeing that the zone management (ZMU) unit
became unserviceable 11 times. The ZMU
becomes serviceable when the ZMU power is turned
off and then on. The installed cabin system control
panel (CSCP) software and the ZMU software can
make the ZMU not operate. This will occur if the
signals between the ZMU and the CSCP are not
synchronized correctly. The ZMU controls cabin
lights, passenger signs, reading lights, attendant call
lights and the cabin attendant control panels
(CACP). These systems can not be changed if the
ZMU for that area is not serviceable. The new ZMU
and CSCP software will automatically start the ZMU
again if the signals are not synchronized correctly.
This change will supply better waste tank indication.
The installed overhead electronics units (OEU) and
ZMU software can show the waste tanks empty after
servicing. The waste tanks are 1/16 to 1/8 full after
servicing. The software can also make the waste
tank indication not show new data. This can occur if
the waste tank logic control module (LCM) power is
turned off momentarily. The new OEU and ZMU
software will prevent these problems. A new waste
tank chime is available in the new configuration data
base. The optional chime will prevent chimes after
servicing that are not necessary.
This change will remove failure indications for the
OEU that are not necessary. After a CSCP "QUICK
TEST" or an "ALL TEST" the OEU can show an
internal failure. The failure is shown for OEU's
connected to a light ballast. The new OEU software
will not cause an internal failure for OEU's
connected to a light ballast.
This change will make sure the CSCP display is
seen when the CSCP is on. The installed CSCP
software can cause the display to not be seen when
the CSCP is on. This will occur if the CSCP power
is off momentarily. Selections can be made on the
CSCP when the display is not seen. The new
CSCP software will make sure the display is seen
when the CSCP is on.
ACTION (PRR 61596)
Remove the installed CSCP. Install a new CSCP.
Make a new CMS configuration database. Install
new operating system (OPS) software for the CSCP.
Install new OPS software for the ZMU. Install new
OPS software for the passenger address controller
(PAC). Install new OPS software for the cabin
interphone controller (CIC). Install new OPS
software for the CACP. Install new OPS software
for the SDM. Install new OPS software for the OEU.
Install new OPS software for the SEU. Install the
new configuration database.
BOEING COMMERCIAL AIRPLANE GROUP P.O. BOX 3707 SEATTLE, WASHINGTON 98124-2207 Summary Page 1 of 2

### Page 2

BOEING SERVICE BULLETIN 777-23-0010
COMPLIANCE
No compliance time is given.
EFFECTIVITY
Operator Airplanes
ANA WA131-WA132
BAB WA078-WA080
GUN WA116
UAL WA003, WA005-WA012
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for
airplanes in warranty as of July 29, 1995. Please
refer to Paragraph I.F., Industry Support Information.
MANPOWER
Total Man-hours - 5.5 for each airplane
Elapsed Time - 5.5 Hours
The change to the CSCP as given in the component
service bulletin 285W0011-23-01 is not included.
MATERIAL INFORMATION
Boeing Supplied Kits
Refer to Paragraph I.H., Material - Price and
Availability.
REPLACE THE CSCP
SHROUDFORWARD GALLEY
(TYPICAL)
CABIN SYSTEM
CONTROL PANEL
(CSCP)
INSTALL NEW CMS
SOFTWARE ON THE
CSCP
R73150
Apr 25/96
Summary Page 2 of 2

### Page 3

Commercial
Airplane
Group
777
Service Bulletin
Number: 777-23-0010
Date: April 25, 1996
ATA System: 2339
SUBJECT: COMMUNICATIONS - CABIN MANAGEMENT SYSTEM - SOFTWARE CHANGE
I. PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index Document D624W001, Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
This service bulletin is for the airplanes shown below. An equivalent change is on subsequent
production airplanes. Refer to PRR 61596 for data about this change.
IDENTIFICATION BY CUSTOMER, CUSTOMER CODE, GROUP AND VARIABLE NUMBER
ALL NIPPON AIRWAYS CO. LTD. (ANA)
WA131-WA132
BRITISH AIRWAYS (BAB)
WA078-WA080
CHINA SOUTHERN AIR GROUP (GUN)
WA116
UNITED AIR LINES, INC. (UAL)
WA003 WA005-WA012
IDENTIFICATION BY VARIABLE NUMBER
WA003 WA005-WA012 WA078-WA080 WA116 WA131-WA132
2. Spares
Examine your spares supply for the parts identified in Paragraph II.D., Existing Parts
Accountability. If any parts are found, refer to Paragraph II.D., Existing Parts Accountability, for
the recommended use.
Apr 25/96 777-23-0010
Page 1 of 30

### Page 4

BOEING SERVICE BULLETIN 777-23-0010
B. Reason
This change will make the cabin management system (CMS) operate with less problems.
This change will make sure that passenger address (PA) announcements can be heard. The
installed speaker drive module (SDM) software can cause some PA announcements to not be heard.
The SDM will turn off the digital sound receivers if a chime occurs. The announcement has to be
made again after the chime stops. The installed seat electronics unit (SEU) software can also cause
some PA announcements to not be heard. The SEU can cause damage to some PA signals to the
passenger control units (PCU). The PCU can accept the damaged digital signal as a different signal
or reject the signal. The new SDM and SEU software will prevent these problems. New speaker
volume adjustments are available in the new configuration data base (CDB). The optional volume
adjustments will increase the PA announcement volume for the cabin attendants.
This change will make sure all the passenger cabin functions of the CMS operate. One operator told
Boeing that the zone management (ZMU) unit became unserviceable 11 times. The ZMU becomes
serviceable when the ZMU power is turned off and then on. The installed cabin system control panel
(CSCP) software and the ZMU software can make the ZMU not operate. This will occur if the signals
between the ZMU and the CSCP are not synchronized correctly. The ZMU controls cabin lights,
passenger signs, reading lights, attendant call lights and the cabin attendant control panels (CACP).
These systems can not be changed if the ZMU for that area is not serviceable. The new ZMU and
CSCP software will automatically start the ZMU again if the signals are not synchronized correctly.
This change will supply better waste tank indication. The installed overhead electronics units (OEU)
and ZMU software can show the waste tanks empty after servicing. The waste tanks are 1/16 to 1/8
full after servicing. The software can also make the waste tank indication not show new data. This
can occur if the waste tank logic control module (LCM) power is turned off momentarily. The new
OEU and ZMU software will prevent these problems. A new waste tank chime is available in the new
configuration data base. The optional chime will prevent chimes after servicing that are not
necessary.
This change will remove failure indications for the OEU that are not necessary. After a CSCP
"QUICK TEST" or an "ALL TEST" the OEU can show an internal failure. The failure is shown for
OEU's connected to a light ballast. The new OEU software will not cause an internal failure for
OEU's connected to a light ballast.
This change will make sure the CSCP display is seen when the CSCP is on. The installed CSCP
software can cause the display to not be seen when the CSCP is on. This will occur if the CSCP
power is off momentarily. Selections can be made on the CSCP when the display is not seen. The
new CSCP software will make sure the display is seen when the CSCP is on.
C. Description
The installed CSCP is removed. A new CSCP is installed. A new CMS CDB is made. New
operating system (OPS) software for the CSCP is installed. New OPS software for the ZMU is
installed. New OPS software for the passenger address controller (PAC) is installed. New OPS
software for the cabin interphone controller (CIC) is installed. New OPS software for the CACP is
installed. New OPS software for the SDM is installed. New OPS software for the OEU is installed.
New OPS software for the SEU is installed. The new CDB is installed.
D. Compliance
No compliance time is given.
Apr 25/96 777-23-0010
2

### Page 5

BOEING SERVICE BULLETIN 777-23-0010
E. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes
specified in this service bulletin comply with the applicable Federal Aviation Regulations (FAR) and
are FAA approved. The changes specified in this service bulletin also comply with the applicable
Joint Airworthiness Requirements (JAR) and are FAA approved as delegated by the Joint Aviation
Authorities (JAA). This service bulletin and the FAA approval were based on the airplane in its
original configuration or as modified by other FAA approved Boeing changes.
Note : Interior arrangements are not evaluated for JAR compliance.
If an airplane has a non-Boeing modification or repair that affects a component or system also
affected by this service bulletin, the operator is responsible for obtaining appropriate regulatory
agency approval before incorporating this service bulletin.
F. Industry Support Information
Boeing warranty remedies are available for 777 airplanes in warranty as of July 29, 1995. For
man-hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing
Product Assurance Contracts. The kits for airplanes in warranty as of that date will be supplied at no
charge. Send a purchase order for the kits to Boeing Spares. Please refer to this service bulletin
number and reference the airplane variable number(s) in your purchase order.
G. Manpower
Approximately five and one-half man-hours and one person are necessary to do this change for each
airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
man-hour data if necessary. The estimate does not include lost time. These are some examples of
lost time:
- Time to adjust to the workplace
- Time to schedule the work
- Time to examine the work
- Time to cure the materials
- Time to make the parts
- Time to find the tools.
H. Material - Price and Availability
Boeing can supply the kits shown in Paragraph II.A., Parts Necessary For Each Airplane as shown
below. Kit availability is shown in the Reorder Lead Time (ROLT). ROLT is calculated from the date
Boeing gets the purchase order.
Kit Number Name
ROLT
(weeks)
Unit Price thru
Nov 30/96
005W1030-1 Top Kit, CMS Software 11 $920.00
The kits are subject to the terms and conditions of the Boeing standard purchase order
acknowledgment. After the Unit Price date, new price and ROLT data is applicable. Prices are in
United States Dollars. Terms: Net 30 days.
Send purchase orders and letters about the supply data to the Director of Spares and refer to this
service bulletin number.
Apr 25/96 777-23-0010
3

### Page 6

BOEING SERVICE BULLETIN 777-23-0010
I. Special Tools - Price and Availability
None
J. Weight and Balance
None
Apr 25/96 777-23-0010
4

### Page 7

BOEING SERVICE BULLETIN 777-23-0010
K. References
1. Existing Data:
a. Engineering Change Memo PRR 61596
b. 777 Maintenance Manual (AMM) Subject 23-39-00, 23-39-12
c. 777 Configuration Database Generator (CDG) User Manual D634W601-1
d. Boeing Component Service Bulletin 285W0011-23-01, "Communications - Cabin System
Control Panel Change"
2. Data supplied with this service bulletin:
None
3. Installation Drawings:
None
L. Publications Changed
Publication Chapter-Section
777 Maintenance Manual 23-39
777 Illustrated Parts Catalog 23-39
777 Fault Isolation Manual 23-39
M. Electrical Load Data
Not changed
Apr 25/96 777-23-0010
5

### Page 8

BOEING SERVICE BULLETIN 777-23-0010
II. MATERIAL INFORMATION
A. Parts Necessary For Each Airplane
1. Kits:
To get the kit shown below, refer to Paragraph I.H., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph II.A.2., Parts and Materials Supplied by the
Operator, are necessary for each airplane.
005W1030 TOP KIT - CABIN MANAGEMENT SYSTEM SOFTWARE
CHANGE
-1
Quantity Part Number Name
- 005W1030-1 Top Kit, CMS Software Change
1 285W0274-3 Disk Set, OEU S/W
1 285W0277-3 Disk Set, SDM S/W
1 285W0280-3 Disk Set, SEU S/W
1 285W0283-3 Disk Set, ZMU S/W
1 285W0289-3 Disk Set, PAC S/W
1 285W0295-3 Disk Set, CSCP S/W
1 285W0298-3 Disk Set, CACP S/W
1 285W0304-3 Disk Set, CDG-03 S/W
2. Parts and Materials Supplied by the Operator:
Quantity Part Number Name
1 222W0015-20 BFE Source Data Disk Set (for
airplane WA116 only)
1 222W0015-21 BFE Source Data Disk Set (for
airplane WA132 only)
B. Parts Necessary to Change Spares
None
C. Special Tools and Equipment
No special tools or equipment are necessary to do the change in this service bulletin. But,
maintenance and overhaul tools in the manuals given in Paragraph I.K., References, can be
necessary. Examine operator tool supply to make sure all necessary tools are available.
D. Existing Parts Accountability
The parts shown below are changed as shown in this service bulletin. Quantity is the number of parts
changed on each airplane.
Existing Part Number RUC Name Quantity New Part Number PNC RC
285W0011-2 RWI CSCP 1 285W0011-3 S A
Apr 25/96 777-23-0010
6

### Page 9

BOEING SERVICE BULLETIN 777-23-0010
RUC Recommended Use Code
RWI - Make the change given in Component Service Bulletin 285W0011-23-01.
PNC Part Number Code
S - This is the part number for the new equivalent or replacement part.
- To get a new part, use this part number in your order.
RC Replacement Code
A - Do not use the existing part to replace the new or changed part.
Apr 25/96 777-23-0010
7

### Page 10

BOEING SERVICE BULLETIN 777-23-0010
BLANK PAGE
Apr 25/96 777-23-0010
8

### Page 11

BOEING SERVICE BULLETIN 777-23-0010
III. ACCOMPLISHMENT INSTRUCTIONS
NOTES:
1. The paragraphs identified with a letter give the general work instructions and the necessary tests.
The instructions identified with numbers on the figures give the recommended sequence of steps.
2. Obey all of the warnings and cautions given in the specified manual sections.
A. Make sure that the cabin management system is serviceable.
B. Touch these selections on the CSCP:
1. CABIN MAINTENANCE
2. CABIN TESTS
3. START QUICK TEST
4. CONTINUE TEST
C. See that NO FAULTS is shown on the CSCP. If NO FAULTS is not shown, see if the failures can be
ignored.
1. SEAT ELECTRONIC UNIT (SEU) X-Y-ZZ HAS AN INTERNAL FAULT, Maintenance Message
23-03610. This failure can be ignored if the seat video displays do not have snow or bars; and,
one audio channel at the seats operates.
2. SEAT ELECTRONIC UNIT (SEU) X-Y-ZZ HAS AN RF BUS FAULT, Maintenance Message
23-03664. This failure can be ignored if the seat video displays do not have snow or bars; and,
one audio channel at the seats operates.
3. SEAT ELECTRONIC UNIT (SEU) X-Y-ZZ HAS AN RF BUS FAULT, Maintenance Message
23-03665. This failure can be ignored if the seat video displays do not have snow or bars; and,
one audio channel at the seats operates.
4. OVERHEAD ELECTRONICS UNIT (OEU) X-Y-ZZ HAS AN INTERNAL FAULT, Maintenance
Message 23-03410. This failure can be ignored if the Maintenance Message is caused by a light
ballast.
5. CSCP HAS AN INTERNAL AUDIO JACK FAULT, Maintenance Message 23-02940
6. CSCP HAS AN INTERNAL VIDEO PREVIEW FAULT, Maintenance Message 23-02938
Remove all other CMS faults before the next instruction step.
D. Change the CSCP as specified in Figure 1.
E. Install the new CSCP OPS software 2376-BCE-011-03 (disk set 285W0295-3). Refer to the 777 AMM
23-39-00, Data Installation From The CSCP Drive To The CSCP Mass Storage, for the necessary
procedures. Do not install or do a verification test of the CSCP database software.
F. Install this new software to the CSCP mass storage. Refer to the 777 AMM 23-39-00, Data
Installation From The CSCP Drive To The CSCP Mass Storage, for the necessary procedures.
NOTE: This step is not necessary if the software is installed on the new CSCP.
Apr 25/96 777-23-0010
9

### Page 12

BOEING SERVICE BULLETIN 777-23-0010
1. ZMU OPS, 237F-BCE-018-03 (disk set 285W0283-3)
2. PAC OPS, 2372-BCE-015-03 (disk set 285W0289-3)
3. CIC OPS, 2377-BCE-010-03 (disk set 285W0286-3)
4. CACP OPS, 231F-BCE-00Y-03 (disk set 285W0298-3)
5. SDM OPS, 2370-BCE-017-03 (disk set 285W0277-3)
6. OEU OPS, 2373-BCE-014-03 (disk set 285W0274-3)
7. SEU OPS, 2371-BCE-016-03 (disk set 285W0280-3)
G. Install the new OPS software to the necessary units. Refer to the 777 AMM 23-39-00, Operational
Program Software Installation, for the necessary procedures. Do not install or do a verification test of
the CSCP database software.
NOTES:
1. The CONFIGURATION CHECK procedure can show more components than are installed on
the airplane. Install the new software for the installed components only. This occurs because
the CDB is not installed.
2. Ignore the failure CSCP Configuration Database is Missing or Failed, Maintenance Message
23-02819.
3. Ignore the failure Configuration Database is Missing or Failed, Maintenance Message 23-0101.
4. Ignore the display "NOTE: NO DATABASE INSTALLED" when software is installed to the
CSCP.
5. Ignore the displays "PASSENGER ADDRESS FAIL" and "CABIN INTERPHONE FAIL" when
software is installed to the CACP.
H. Install this software to the CSCP mass storage. Refer to the 777 AMM 23-39-00, Data Installation
From The CSCP Drive To The CSCP Mass Storage, for the necessary procedures.
NOTE: This step is not necessary if the software is installed on the new CSCP. This software is not
changed by this service bulletin.
1. CSMU OPS, 2374-BCE-012-02 (disk set 285W0292-2)
2. EMC OPS, 2375-BCE-013-02 (disk set 285W0301-2)
I. Install this vendor software to the CSCP mass storage. Refer to the 777 AMM 23-39-00, Data
Installation From The CSCP Drive To The CSCP Mass Storage, for the necessary procedures.
NOTES:
1. This step is not necessary if the software is installed on the new CSCP. This software is not
changed by this service bulletin.
2. Other software can be installed on the CSCP. This data provides the software part numbers of
the initial airplane configuration.
Apr 25/96 777-23-0010
10

### Page 13

BOEING SERVICE BULLETIN 777-23-0010
3. This data includes the changes made by service bulletin 777-23-0005 for airplanes
WA006-WA007.
Operator Software Part Number Disk Set Part Number Software Name
ANA 2372MEI20000 212-NH01 CSCP DP S/W
2373MEI30000 215-02001 VIU OPS S/W
2376MEI30500 215-11001 VDU OPS S/W
BAB 2373GMI00100 3931/03931/BA01 CSCP OPS S/W
237AGMI00800 3931/03941/BA01 PRAM UTILITY S/W
237BGMI00900 3931/03921/BA03 ARU UTILITY S/W
2371GMI00300 3931/03961/BA01 VIU UTILITY S/W
2377GMI00500 3931/03971/BA01 SVU UTILITY S/W
2375GMI00700 3931/03951/BA01 CFS UTILITY S/W
2372GMI01100 3931/04201/BA03 VIU S/W
2373GMI01000 3931/04211/BA01 VDU S/W
2377GMI01400 3931/04171/BA03 ZNTU S/W
GUN 230DSHW00A10 914950-0502 AIRSHOW S/W
2372MEI21001 212-CZ02 CSCP OPS S/W
2373MEI30000 215-02001 VIU OPS S/W
2376MEI30500 215-11001 VDU OPS S/W
UAL 393100671BA02 3931/03981/BA02 CSCP OPS S/W
393101711BA02 3931/03921/BA02 ARU UTILITY S/W
393101721BA02 3931/03991/BA02 CFS UTILITY S/W
393101731BA02 3931/04011/BA02 SVU UTILITY S/W
393101741BA02 3931/04001/BA02 VIU UTILITY S/W
393104501BA02 3931/04201/BA02 VIU S/W
393103691BA02 3931/04171/BA02 ZNTU S/W
J. Install the new configuration database to the CSCP mass storage. Refer to the 777 AMM 23-39-00,
Data Installation From The CSCP Drive To The CSCP Mass Storage, for the necessary procedures.
Apr 25/96 777-23-0010
11

### Page 14

BOEING SERVICE BULLETIN 777-23-0010
The new configuration database is made by changing the installed configuration database. The
configuration database generator (CDG) 285W0347-3 (disk set 285W0304-3) is used to change the
installed configuration database. Do these steps to get the new database disk set:
For BAB and UAL:
1. Convert the database. Refer to the 777 CDG User Manual section 1-7, "Opening an Existing
Database" for the necessary instructions.
NOTES:
1. Use disk number two of the installed configuration database disk set to get the necessary
files. The "Read Only''' feature must be turned off to change the files.
2. The letters "CDB" are used to show the database was made at Boeing. Use different letters
in the new database name.
2. Do a check of the new database. Refer to the 777 CDG User Manual section 4-51, "Task 5. Check
the Database for Consistency" for the necessary instructions.
3. Remove any database "Critical Errors". Refer to the 777 CDG User Manual section 4-53, "Task 6.
Correct Errors" for the necessary instructions.
NOTE: "Warnings" are not "Critical Errors" and do not need to be removed.
4. Include the buyer furnished equipment (BFE) data. The BFE data will need to be converted. Refer
to the 777 CDG User Manual section 4-56, "Task 7. Export to BFE" for the necessary instructions.
Use the offline database generator (ODG) software shown below to make the BFE database files.
Airplane ODG S/W
WA006-WA007 393/1/04391/BA01
WA008-WA011 393/1/04391/BA02
WA003, WA005, WA012
and WA078-WA080
2378-GMI-029-01
NOTE: Changes to the BFE database files must be coordinated with GEC-Marconi InFlight
Systems Limited, Attention Dave Etchells, Customer Services Manager, Browns Lane,
The Airport, Portsmouth, Hampshire, England PO3 5PH, Telephone Number
(1705)-664966.
5. Make the database disk set. Refer to the 777 CDG User Manual section 4-58, "Task 8. Make the
Data-Load Disk for CMS" for the necessary instructions.
For ANA and GUN:
1. Convert the database. Refer to the 777 CDG User Manual section 1-7, "Opening an Existing
Database" for the necessary instructions.
2. Do a check of the new database. Refer to the 777 CDG User Manual section 4-51, "Task 5. Check
the Database for Consistency" for the necessary instructions.
Apr 25/96 777-23-0010
12

### Page 15

BOEING SERVICE BULLETIN 777-23-0010
3. Remove any database errors. Refer to the 777 CDG User Manual section 4-53, "Task 6. Correct
Errors" for the necessary instructions.
NOTE: The letters "CDB" are used to show the database was made at Boeing. Use different
letters in the new database name.
4. Change the database part number in the BFE files.
a. Copy the files in the directory MEICSF01 to the directory c:\cdgdb. Copy the files from the
database that is being changed. Use the source data software shown below to get the
necessary files.
Airplane Source Data Software
WA116 222W0015-20
WA131 No Software Necessary
WA132 222W0015-21
b. Open the file meicfs01.100.
c. Change the database part number in the file to the new database part number. Do not change
any other data. Do not convert the file.
d. Save the changed file meicfs01.100.
e. Open the file meicfs01.102.
f. Change the database part number in the file to the new database part number. The database
part number is in two places. Do not change any other data. Do not convert the file.
g. Save the changed file meicfs01.102.
5. Make the database disk set. Refer to the 777 CDG User Manual section 4-58, "Task 8. Make the
Data-Load Disk for CMS" for the necessary instructions.
a. The data below provides the CDB part numbers of the initial airplane configuration.
Operator Airplane(s) CDB Software Part
Number
xzz CDB Disk Set Part
Number
ANA WA131 2376-CDB-003-01 301 222W0014-5
WA132 2374-CDB-003-03 303 222W0014-21
BAB WA078-WA080 2377-CDB-001-02 102 222W0014-14
GUN WA116 2373-CDB-004-03 403 222W0014-20
Apr 25/96 777-23-0010
13

### Page 16

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
Operator Airplane(s) CDB Software Part
Number
xzz CDB Disk Set Part
Number
UAL WA003, WA005 2373-CDB-000-07 007 222W0014-15
WA006-WA007 2377-CDB-000-03 003 222W0014-10
WA008-WA010 2370-CDB-000-04 004 222W0014-11
WA011 2371-CDB-000-05 005 222W0014-12
WA012 2375-CDB-000-10 010 222W0014-27
b. A new waste tank chime is available in the changed database. The new chime will prevent
waste-tank-full chimes which are not necessary. The new chime can be set with these
selections.
1. Set the "Waste tank full chime" to "In Config" . Refer to the 777 CDG User Manual section
4-174, "Assign Chime Sounds" for the necessary instructions.
2. Make a selection for the "Chime type". Refer to the 777 CDG User Manual section 4-174,
"Assign Chime Sounds" for the necessary instructions.
3. Make a selection of one or more speakers in the "Chime Speakers Definition" screen. Refer
to the 777 CDG User Manual section 4-174, "Assign Chime Sounds" for the necessary
instructions.
4. If installed, remove the OEU "Special Functions, Function Number" 22, 23 and 24. Refer to
the 777 CDG User Manual section 4-218, "Define the OEU Analog Input" for the necessary
instructions.
c. Seat letters from A to Z are available in the changed database. Refer to the 777 CDG User
Manual section 4-63, "Configuring the Seating" for the necessary instructions.
d. The changed database lets some primary LRU ports be taken out of the airplane configuration.
These ports can be removed from the database configuration if the "Location Description" is
"Not Wired". Refer to the 777 CDG User Manual section 5-209, "Port Assignment - [primary
LRU]" for the necessary instructions.
1. Port Assignment - CSMU, CSMU Master Override
2. Port Assignment - PAC, PAC PA Area 1 through 6 Discrete Out
3. Port Assignment - CIC, CIC Call from Cargo Loadmaster
4. Port Assignment - CIC, CIC Video In Use Input
5. Port Assignment - CIC, CIC Cargo Call Message
6. Port Assignment - CIC, CIC Cargo Loadmaster Call
7. Port Assignment - CIC, CIC Purser Page
e. The CDG 285W0347-3 lets two different databases be compared. Refer to the 777 CDG User
Manual section 8-6, "Generating a Differences Report" for the necessary instructions.
Apr 25/96 777-23-0010
14

### Page 17

BOEING SERVICE BULLETIN 777-23-0010
f. The CDG 285W0347-3 has a new selection called "Release Notes editor". This selection can
be used to write data about the CDB. Refer to the 777 CDG User Manual section 9-7, "Writing
Release Notes" for the necessary instructions.
g. The CDG 285W0347-3 can have a different speaker attenuation value for each speaker.
Changes to the speaker attenuation values will make the PA announcements easier to hear.
Changes to the speaker attenuation values must be made as specified in the tables that follow.
Refer to the 777 CDG User Manual section 4-124, "Task 4. Define the Speakers" for the
necessary instructions.
The CDG 285W0347-3 can have more speakers muted when a handset is used. Changes to
the number of speakers muted for each handset can make PA announcements easier to hear.
Refer to the 777 CDG User Manual section 4-146, "Task 4. Assign and Mute Speakers" for the
necessary instructions.
Changes to the speaker attenuation values and the muted speakers must be made as specified
in the tables that follow. All these changes together give an approved speaker configuration.
ANA, WA131-WA132
Speaker Definition, Changes
Speaker ID
Initial volume Speaker attenuation
Set to: (was) Set to: (was)
1 no chng 11 3 6
3 no chng 11 0 6
4 no chng 11 0 6
5 no chng 11 0 6
6 no chng 11 0 6
7 11 12 no chng 6
8 11 12 no chng 6
11 no chng 11 5 6
12 no chng 11 5 6
13 no chng 11 0 6
14 no chng 11 0 6
15 no chng 11 0 6
16 no chng 11 0 6
Apr 25/96 777-23-0010
15

### Page 18

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
ANA, WA131-WA132
17 no chng 11 0 6
18 no chng 11 0 6
19 no chng 11 0 6
20 no chng 11 0 6
21 no chng 11 0 6
22 no chng 11 0 6
23 no chng 12 0 6
24 no chng 12 0 6
25 no chng 12 0 6
26 no chng 12 0 6
27 12 11 7 6
28 12 11 7 6
29 12 11 no chng 6
30 12 11 no chng 6
31 no chng 12 0 6
32 no chng 12 0 6
33 no chng 12 0 6
34 no chng 12 0 6
35 no chng 12 0 6
36 no chng 12 0 6
37 no chng 12 0 6
38 no chng 12 0 6
39 no chng 12 5 6
Apr 25/96 777-23-0010
16

### Page 19

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
ANA, WA131-WA132
40 no chng 12 5 6
61 9 8 7 6
62 9 8 7 6
63 9 8 7 6
64 9 8 7 6
65 no chng 10 8 6
66 no chng 10 8 6
81 9 8 11 6
82 9 8 11 6
83 9 8 11 6
84 9 8 11 6
85 10 9 12 6
86 10 9 12 6
87 10 9 12 6
88 10 9 12 6
101 no chng 9 0 6
102 no chng 9 0 6
104 no chng 9 0 6
105 no chng 9 0 6
106 no chng 10 0 6
107 no chng 10 0 6
Chime and Mute Speaker Identification, Changes
Apr 25/96 777-23-0010
17

### Page 20

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
ANA, WA131-WA132
Handset
Mute
1 2 3 4 5
CAH (21) ZMU 1 Port 2 2 61 82 62
CAH (61) ZMU 1 Port 3 61 62 81 82
CAH (51) ZMU 1 Port 5 62 61 82
CAH (12) ZMU 2 Port 1 9 11 83 63
CAH (22) ZMU 2 Port 2 10 12 84 63
CAH (23) ZMU 2 Port 3 28 30 86 64
CAH (13) ZMU 3 Port 1 27 29 85 64
CAH (14) ZMU 3 Port 2 65 87 39
CAH (24) ZMU 3 Port 3 66 88 40
CAH (62) ZMU 3 Port 4 65 66 87 88
PAC Ports, Changes
PAC Port In Cnf
Was Set to:
PAC Decompression Out No Yes
BAB, WA078-WA080
Speaker Definition, Changes
Speaker ID
Initial volume Speaker attenuation
Set to: (was) Set to: (was)
1 no chng 11 3 6
2 no chng 11 3 6
3 no chng 11 0 6
Apr 25/96 777-23-0010
18

### Page 21

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
BAB, WA078-WA080
4 no chng 11 0 6
5 no chng 11 0 6
6 no chng 11 0 6
7 no chng 11 0 6
8 no chng 11 0 6
11 no chng 11 5 6
12 no chng 11 5 6
13 no chng 11 0 6
14 no chng 11 0 6
15 no chng 11 0 6
16 no chng 11 0 6
17 no chng 11 0 6
18 no chng 11 0 6
19 no chng 11 0 6
20 no chng 11 0 6
21 no chng 11 0 6
22 no chng 11 0 6
23 no chng 12 0 6
24 no chng 12 0 6
25 no chng 12 0 6
26 no chng 12 0 6
27 12 11 7 6
28 12 11 7 6
29 12 11 no chng 6
30 12 11 no chng 6
Apr 25/96 777-23-0010
19

### Page 22

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
BAB, WA078-WA080
31 no chng 12 0 6
32 no chng 12 0 6
33 no chng 12 0 6
34 no chng 12 0 6
35 no chng 12 0 6
36 no chng 12 0 6
37 no chng 12 0 6
38 no chng 12 0 6
39 no chng 12 5 6
40 no chng 12 5 6
61 no chng 10 8 6
62 no chng 9 7 6
63 9 8 7 6
64 7 8 5 6
65 no chng 10 8 6
66 no chng 10 8 6
81 9 8 11 6
82 9 8 11 6
83 9 8 11 6
84 9 8 11 6
85 10 9 12 6
86 10 9 12 6
87 10 9 12 6
88 10 9 12 6
101 no chng 9 0 6
Apr 25/96 777-23-0010
20

### Page 23

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
BAB, WA078-WA080
102 no chng 9 0 6
103 no chng 9 0 6
104 no chng 9 0 6
105 no chng 9 0 6
106 no chng 9 0 6
107 no chng 9 0 6
108 no chng 9 0 6
109 no chng 9 0 6
110 no chng 9 0 6
Chime and Mute Speaker Identification, Changes
Handset
Mute
1 2 3 4 5
CAH (21) ZMU 1 Port 2 2 62 82 61
CAH (12) ZMU 2 Port 1 9 11 83 64
CAH (22) ZMU 2 Port 2 10 12 84 64
CAH (14) ZMU 3 Port 2 65 87 39
CAH (24) ZMU 3 Port 3 66 88 40
PAC Ports, Changes
PAC Port In Cnf
Set to: Was
PAC Decompression Out Yes No
ANS Area Descriptions, Changes (a)
Area
Number Description
Reference
Noise Level
3 ANS Area 3 75 dB 76 dB
Apr 25/96 777-23-0010
21

### Page 24

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
BAB, WA078-WA080
(a) Refer to the 777 CDG User Manual section 4-121, "Task 3.
Define the ANS Area" for the necessary instructions.
GUN, WA116
Speaker Definition, Changes
Speaker ID
Initial volume Speaker attenuation
Set to: (was) Set to: (was)
1 no chng 11 3 6
2 no chng 11 3 6
3 no chng 11 0 6
4 no chng 11 0 6
5 no chng 11 0 6
6 no chng 11 0 6
7 11 12 0 6
8 11 12 0 6
11 no chng 11 5 6
12 no chng 11 5 6
13 no chng 11 0 6
14 no chng 11 0 6
15 no chng 11 0 6
16 no chng 11 0 6
17 no chng 11 0 6
18 no chng 11 0 6
19 no chng 11 0 6
Apr 25/96 777-23-0010
22

### Page 25

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
GUN, WA116
20 no chng 11 0 6
21 no chng 11 0 6
22 no chng 11 0 6
23 no chng 12 0 6
24 no chng 12 0 6
25 no chng 12 0 6
26 no chng 12 0 6
27 no chng 11 7 6
28 no chng 11 7 6
31 no chng 12 0 6
32 no chng 12 0 6
33 no chng 12 0 6
34 no chng 12 0 6
35 no chng 12 0 6
36 no chng 12 0 6
37 no chng 12 0 6
38 no chng 12 0 6
39 no chng 12 5 6
40 no chng 12 5 6
61 9 8 7 6
62 9 8 7 6
63 9 8 7 6
64 no chng 7 5 6
Apr 25/96 777-23-0010
23

### Page 26

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
GUN, WA116
65 no chng 10 8 6
66 no chng 10 8 6
81 9 8 11 6
82 9 8 11 6
83 9 8 11 6
84 9 8 11 6
85 10 9 12 6
86 10 9 12 6
87 10 9 12 6
88 10 9 12 6
101 no chng 9 0 6
102 no chng 9 0 6
103 no chng 10 0 6
104 no chng 9 0 6
105 no chng 9 0 6
106 no chng 9 0 6
107 no chng 9 0 6
108 no chng 9 0 6
109 no chng 10 0 6
110 no chng 10 0 6
Chime and Mute Speaker Identification, Changes
Handset
Mute
1 2 3 4 5
Apr 25/96 777-23-0010
24

### Page 27

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
GUN, WA116
CAH (21) ZMU 1 Port 2 2 61 82 62
CAH (12) ZMU 2 Port 1 9 11 83 63
CAH (22) ZMU 2 Port 2 10 12 84 63
CAH (23) ZMU 2 Port 3 28 30 86 64
CAH (13) ZMU 3 Port 1 27 29 85 64
CAH (14) ZMU 3 Port 2 65 87 39
CAH (24) ZMU 3 Port 3 66 88 40
CAH (04) ZMU 3 Port 4 65 66 87 88
UAL, WA003, WA005-WA012
Speaker Definition, Changes
Speaker ID
Initial volume Speaker attenuation
Set to: (was) Set to: (was)
3 no chng 11 0 6
4 no chng 11 0 6
5 no chng 11 0 6
6 no chng 11 0 6
7 no chng 12 0 6
8 no chng 12 0 6
11 no chng 11 5 6
12 no chng 11 5 6
13 no chng 11 0 6
14 no chng 11 0 6
Apr 25/96 777-23-0010
25

### Page 28

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
UAL, WA003, WA005-WA012
15 no chng 11 0 6
16 no chng 11 0 6
17 no chng 11 0 6
18 no chng 11 0 6
19 no chng 11 0 6
20 no chng 11 0 6
21 no chng 11 0 6
22 no chng 11 0 6
23 no chng 12 0 6
24 no chng 12 0 6
25 no chng 12 0 6
26 no chng 12 0 6
27 12 11 7 6
28 12 11 7 6
29 12 11 no chng 6
30 12 11 no chng 6
31 no chng 12 0 6
32 no chng 12 0 6
33 no chng 12 0 6
34 no chng 12 0 6
35 no chng 12 0 6
36 no chng 12 0 6
37 no chng 12 0 6
Apr 25/96 777-23-0010
26

### Page 29

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
UAL, WA003, WA005-WA012
38 no chng 12 0 6
39 no chng 12 5 6
40 no chng 12 5 6
61 9 8 7 6
62 9 8 7 6
63 9 8 7 6
64 no chng 7 5 6
65 no chng 10 8 6
66 no chng 10 8 6
81 9 8 11 6
82 9 8 11 6
83 9 8 11 6
84 9 8 11 6
85 10 9 12 6
86 10 9 12 6
87 10 9 12 6
88 10 9 12 6
101 no chng 9 0 6
102 no chng 9 0 6
103 no chng 9 0 6
104 no chng 9 0 6
105 no chng 9 0 6
106 no chng 9 0 6
Apr 25/96 777-23-0010
27

### Page 30

BOEING SERVICE BULLETIN 777-23-0010
(Continued)
UAL, WA003, WA005-WA012
107 no chng 10 0 6
108 no chng 9 0 6
109 no chng 10 0 6
110 no chng 10 0 6
Chime and Mute Speaker Identification, Changes
Handset
Mute
1 2 3 4 5
CAH (82) ZMU 2 Port 1 9 11 83 63
CAH (84) ZMU 2 Port 2 10 12 84 63
CAH (23) ZMU 2 Port 3 28 30 86 64
CAH (81) ZMU 2 Port 4 9 11 83 63
CAH (83) ZMU 2 Port 5 10 12 84 63
CAH (13) ZMU 3 Port 1 27 29 85 64
CAH (14) ZMU 3 Port 2 65 87 39
CAH (24) ZMU 3 Port 3 66 88 40
Apr 25/96 777-23-0010
28

### Page 31

BOEING SERVICE BULLETIN 777-23-0010
21
SHROUD
(TYPICAL)
FORWARD GALLEY
CABIN SYSTEM CONTROL PANEL (CSCP)
R73152
FIGURE 1. CHANGE THE CSCP
Apr 25/96 SHEET 1 OF 2 777-23-0010
29

### Page 32

BOEING SERVICE BULLETIN 777-23-0010
The step numbers shown below agree with the numbers shown in the circle symbols in the figure.
STEP TASK NAME PART NUMBER QTY NOTES
1 Remove CSCP 285W0011-2 1 Refer to the 777 AMM 23-39-12
for the necessary instructions.
2 Install CSCP 285W0011-3 1 Refer to the 777 AMM 23-39-12
for the necessary instructions.
FIGURE 1. CHANGE THE CSCP
Apr 25/96 SHEET 2 OF 2 777-23-0010
30

### Page 33

Commercial
Airplane
Group
777
Service Bulletin
Number: 777-23-0010 Evaluation FormDate: April 25, 1996
ATA System: 2339
Prepared By: Bill Bottenberg
SUBJECT: COMMUNICATIONS - CABIN MANAGEMENT SYSTEM - SOFTWARE CHANGE
Use this evaluation form to tell us what you think of the quality of this service bulletin. We will use the data
that you give us to improve the quality of our service bulletins. Please include data about these or other
items:
- Did this service bulletin meet your estimate of quality?
- How easy is this service bulletin to understand?
- Are the Planning Information, Material Information and Accomplishment Instructions satisfactory?
- Will you do this service bulletin fully? If not, please tell us why.
- Is the Manpower estimate satisfactory?
NOTE: Please do not use this evaluation form to tell us to make changes to your manuals. To make these
changes, please use a Publication Change Request (PCR) form.
Please give us this data:
OPERATOR: TODAY'S DATE:
PREPARED BY: TITLE:
ORGANIZATION: TELEX CODE:
TELEPHONE NUMBER: BASE:
COMMENTS:
If necessary, please use the other side. Thank you for the time you used to give us your comments.
Give the completed evaluation form to your Boeing Field Service Representative or send the evaluation form
directly to this address:
T.J. Taylor, Manager
Service Bulletin Engineering
Boeing Commercial Airplane Group
P.O. Box 3707, Mail Stop 20-85
Seattle, WA 98124-2207
BOEING COMMERCIAL AIRPLANE GROUP P.O. BOX 3707 SEATTLE, WASHINGTON 98124-2207

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
