# Boeing Special Attention Service Bulletin 777-32-0083: U.S. DOT/FAA - SB-777-32-0083-02

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2013-0789; AD 2014-05-09 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 777-32-0083](https://openairdocs.org/service-documents/boeing/sb-777-32-0083.md)
- Title as filed: U.S. DOT/FAA - SB-777-32-0083-02
- Pages: 34
- PDF: https://openairdocs.org/files/sha256/02/8e/028ebcfd178576396ea4f88d887bc67434f4278a5411fe040600857ca5ec4f94
- Page: https://openairdocs.org/service-documents/boeing/sb-777-32-0083/file/028ebcfd1785

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-32-0083
Original Issue: February 05, 2009
Revision 2: May 02, 2013
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2009 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
1 of 34
4.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
2 of 34
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 4
D. Description .............................................. 1 5
E. Compliance .............................................. 1 5
F. Approval ............................................... 1 7
G. Manpower .............................................. 1 8
H. Weight and Balance Changes .................................... 1 8
I. Electrical Load Data ......................................... 1 8
J. References .............................................. 1 8
1. Existing Data: ......................................... 1 8
2. Data Supplied with this Service Bulletin: ........................... 1 8
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 1 8
K. Publications Affected ........................................ 1 9
L. Interchangeability and Intermixability of Parts ........................... 1 9
M. Software Accomplishment Summary ................................ 1 9
2. MATERIAL INFORMATION ........................................ 2 1
A. Material - Price and Availability ................................... 2 1
B. Industry Support Information .................................... 2 1
C. Parts Necessary for Each Airplane ................................. 2 1
1. Kits/Parts ............................................ 2 1
2. Parts and Materials Supplied by the Operator ........................ 2 2
3. Parts Modified and Reidentified ................................ 2 2
4. Parts Removed and Not Replaced .............................. 2 2
D. Parts Necessary to Change Spares ................................. 2 2
E. Special Tooling - Price and Availability ............................... 2 2
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 2
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 3
A. GENERAL INFORMATION ..................................... 2 3
B. WORK INSTRUCTIONS ....................................... 2 4
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION ................ 2 5
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION ............... 2 7
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT .............. 2 9
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT ............. 3 2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
3 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
4 of 34
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 5

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 777-32-0083Original Issue: February 05, 2009
Revision 2: May 02, 2013
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2012-12-08 is related to this service bulletin.
Group 1 only: No more work is necessary on the airplane(s) that have replaced 112W1769-1 Retract Actuator
Fuse Pins with 112W1769-3 Retract Actuator Fuse Pins in accordance with the Original Issue or Revision 1 of
this service bulletin and have not replaced 112W1769-3 Retract Actuator Fuse Pins with 112W1769-1 Retract
Actuator Fuse Pins.
Group 2 airplanes, 777-200 and 777-300 airplanes line number 164 through 1027, are added to this service
bulletin effectivity. Due to an interchangeability error in the Illustrated Parts Catalog (IPC), it is possible that
112W1769-1 Retract Actuator Fuse Pins were installed on 777-200 and 777-300 airplanes line number 164
through 1027.
REASON FOR REVISION
This revision is sent to update compliance time information for inspection and replacement of the 112W1769-1
fuse pin. This revision also added Group 2 airplanes.
These sections were changed:
1. In Summary, Background, added information about the addition of Group 2 airplanes.
2. In Summary, Background, added Summary Evaluation Table.
3. In Summary, Effectivity, added spares affected reference.
4. In Summary, Compliance, added FAA AD reference.
5. In Summary, Compliance, added information related to the future release of Airworthiness Directive.
6. In Paragraph 1.A.1, Airplanes, added 777-200 and 777-300 airplanes line number 164 through 1027
to Group 2.
7. In Paragraph 1.A.2, Spares Affected, added affected spares.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
5 of 34

### Page 6

8. In Paragraph 1.C., Reason, added information about the addition of Group 2 airplanes.
9. In Paragraph 1.E., Compliance, added FAA AD reference.
10. In Paragraph 1.E., Compliance, added information related to the future release of Airworthiness Directive.
11. In Paragraph 1.E., Compliance, updated compliance table description.
12. In Paragraph 1.E., Compliance, added effective date of Airworthiness Directive.
13. In Paragraph 1.E., Compliance added description for evaluating conditions and actions.
14. In Paragraph 1.E., Compliance, updated compliance time for All Airplanes condition.
15. In Paragraph 1.E., Compliance, updated compliance time for Condition 2A.
16. In Paragraph 1.E., Compliance, updated compliance time for Condition 2B.
17. In Paragraph 1.E., Compliance, updated compliance time for Condition 2C.
18. In Paragraph 1.E., Compliance, added Table 2 for Group 2 airplanes.
19. In Paragraph 1.F., Approval, added alternative method of compliance information for Group 1 airplanes.
20. In Paragraph 1.J.1., Existing Data, added FAA AD reference.
21. In Paragraph 1.K., Publications Affected, added Damage Tolerance Based Structural Inspections
statement.
22. In Paragraph 2.A., Material - Price and Availability, updated ROLT and Unit Price information.
23. In Paragraph 3.A., General Information, deleted note 1.
24. In Paragraph 3.B., Work Instructions, Part 2, added Retract Actuator Fuse Pin part number.
25. FIGURE 1, 2, 3, and 4, added Step Table description paragraph.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
February 05, 2009Original Issue:
February 17, 2011Revision 1:
May 02, 2013Revision 2:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
6 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 7

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 777-32-0083Original Issue: February 05, 2009
Revision 2: May 02, 2013
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will find and replace 112W1769-1 Retract Actuator Fuse Pins. The
112W1769-1 Retract Actuator Fuse Pins have been found to crack and fail earlier than the previously determined
safe life limit of the pins. A fractured Retract Actuator Fuse Pin can cause the main landing gear (MLG) to extend
without restriction and attempt to lock into position under high dynamic loads. Unrestricted MLG extension could
cause structural damage to the side and drag brace lock assemblies, leading to unlocked drag and/or side
braces which could result in landing gear collapse during touchdown, rollout or taxi.
One operator reported that a right MLG 112W1769-1 pin sheared during normal flight operations. The failure
occurred on a pin with 10,874 flight cycles. The left MLG pin was also inspected and was found to be cracked.
Examination of the sheared pin concluded that the cracking was due to fatigue. Three other pins that were
reported to have cracks had between 10,000 and 11,000 flight cycles.
Subsequent to the release of Revision 1 of this service bulletin, it was found that the Illustrated Parts Catalog
(IPC) allowed interchangeability of 112W1769-1 Retract Actuator Fuse Pins with 112W1769-3 Retract Actuator
Fuse Pins on 777-200 and 777-300 airplanes line number 164 through 1027.
This service bulletin provides instructions to inspect the left and right MLG for 112W1769-1 Retract Actuator
Fuse Pins and to replace the affected pins with 112W1769-3 pins.
Boeing Service Related Problem (SRP) 777-SRP-57-0226 is related to this service bulletin.
Boeing Service Letter (SL) 777-SL-57-011 is related to this service bulletin.
Boeing Fleet Team Digest Article (FTD) 777 FTD 57-08005 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
7 of 34

### Page 8

ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedYesSpares Affected
Paragraph 1.E., ComplianceYesAD Related
Paragraph 1.H., Weight and Balance ChangesYesWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedYesPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsYesKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
YesOperator Supplied Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Get access to the left and right MLG Retract Actuator Fuse Pins. Do an inspection of the Retract Actuator Fuse
Pins to identify the part number. If an affected pin is found, replace the pin. If an affected pin is not found, no
further action is required at that pin location.
EFFECTIVITY
777-200 and -300 Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
Refer to Paragraph 1.A.2., Spares Affected for the list of affected components.
COMPLIANCE
Group 1:
Federal Aviation Administration (FAA) Airworthiness Directive AD 2012-12-08 is related to this service bulletin.
Group 2:
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, and/or repair procedures given in this service
bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
8 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 9

MANPOWER
Elapsed HoursTotal Task HoursAirplanes
3.004.50All
MATERIAL INFORMATION
Boeing and Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
9 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 10 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
GET ACCESS TO THE LEFT AND
RIGHT MLG RETRACT ACTUATOR I
FUSE PINS THROUGH PANEL
551DB AND 651DB.
FWD
LEFT MLG SHOWN;
RIGHT MLG OPPOSITE
DO AN INSPECTION OF THE RETRACT ACTUATOR
FUSE PINS TO IDENTIFY THE PART NUMBER. IF AN
AFFECTED PIN IS FOUND, REPLACE THE PIN. IF AN
AFFECTED PIN IS NOT FOUND, NO FURTHER ACTION
IS REQUIRED FOR THAT PIN LOCATION.  FWD
1742524
Original Issue: February 05, 2009
Revision 2: May 02, 2013  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-32-0083
Work - See page 1 for details.  10 of 34

### Page 11

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-32-0083
Original Issue: February 05, 2009
Revision 2: May 02, 2013
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
Refer to Service Bulletin Index Document D624W001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
777-200 and 777-300 Airplanes with line numbers 1 through 163.-1
777-200 and 777-300 Airplanes with line numbers 164 through 1027.-2
Airplane Models:
777-200, 777-300
GroupVariable Number
1WA001 - WA017
1WA076 - WA080
1WA086 - WA093
1WA101 - WA104
1WA116 - WA119
1WA131 - WA137
1WA171 - WA175
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
11 of 34

### Page 12

GroupVariable Number
1WA196 - WA198
1WA206 - WA211
2WA212
1WA221 - WA223
1WA231 - WA232
2WA241 - WA250
2WA261 - WA266
2WA281 - WA283
2WA301 - WA304
1WB001 - WB014
2WB015 - WB021
2WB031 - WB046
1WB051 - WB068
2WB069 - WB088
1WB101 - WB104
2WB105 - WB106
1WB121 - WB125
1WB131 - WB133
2WB134 - WB148
1WB151 - WB153
2WB154 - WB155
1WB161 - WB169
2WB170 - WB177
1WB181 - WB186
2WB187 - WB194
2WB201 - WB215
1WB231 - WB234
2WB235 - WB247
1WB271 - WB272
2WB273
1WB276 - WB286
2WB291 - WB302
1WB306 - WB307
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
12 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 13

GroupVariable Number
1WB311 - WB313
2WB314 - WB335
1WB336
2WB337
2WB341 - WB342
2WB366 - WB368
1WB371
2WB372 - WB388
2WB406
2WB411 - WB413
2WB416 - WB439
2WB446 - WB453
2WB476
2WB481 - WB484
1WB501 - WB504
2WB505 - WB512
1WB531 - WB534
2WB535 - WB537
1WB551 - WB552
2WB553 - WB554
1WB591 - WB592
2WB593 - WB597
1WB601
2WB602 - WB606
2WB611 - WB622
2WB631 - WB638
2WB646 - WB649
2WC051 - WC073
2WC101 - WC104
2WC111 - WC120
2WC221 - WC224
2WC241 - WC243
2WC281 - WC290
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
13 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 14

GroupVariable Number
2WC301 - WC308
2WC361 - WC364
2WC371 - WC374
2WC381 - WC395
2WC441
2WC446 - WC449
2WC456 - WC459
2WC486 - WC493
2WC506 - WC508
2WC521 - WC522
2WC531 - WC536
2WC546 - WC548
2WC556
2WC566 - WC567
2WC571 - WC574
2WC581
2WC586
2WC591 - WC592
2. Spares Affected
Examine your spares supply for the part identified below. If the part is found, it is recommended
to remove the part from your spares supply.
Part Number
112W1769-1
B. Concurrent Requirements
None.
C. Reason
Accomplishment of this service bulletin will find and replace 112W1769-1 Retract Actuator Fuse Pins.
The 112W1769-1 Retract Actuator Fuse Pins have been found to crack and fail earlier than the previously
determined safe life limit of the pins. A fractured Retract Actuator Fuse Pin can cause the main landing
gear (MLG) to extend without restriction and attempt to lock into position under high dynamic loads.
Unrestricted MLG extension could cause structural damage to the side and drag brace lock assemblies,
leading to unlocked drag and/or side braces which could result in landing gear collapse during
touchdown, rollout or taxi.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
14 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 15

One operator reported that a right MLG 112W1769-1 pin sheared during normal flight operations. The
failure occurred on a pin with 10,874 flight cycles. The left MLG pin was also inspected and was found
to be cracked. Examination of the sheared pin concluded that the cracking was due to fatigue. Three
other pins that were reported to have cracks had between 10,000 and 11,000 flight cycles.
Subsequent to the release of Revision 1 of this service bulletin, it was found that the Illustrated Parts
Catalog (IPC) allowed interchangeability of 112W1769-1 Retract Actuator Fuse Pins with 112W1769-3
Retract Actuator Fuse Pins on 777-200 and 777-300 airplanes line number 164 through 1027.
This service bulletin provides instructions to inspect the left and right MLG for 112W1769-1 Retract
Actuator Fuse Pins and to replace the affected pins with 112W1769-3 pins.
Boeing Service Related Problem (SRP) 777-SRP-57-0226 is related to this service bulletin.
Boeing Service Letter (SL) 777-SL-57-011 is related to this service bulletin.
Boeing Fleet Team Digest Article (FTD) 777 FTD 57-08005 is related to this service bulletin.
Revision 2 is sent to update compliance time information for inspection and replacement of the
112W1769-1 fuse pin. This revision also added Group 2 airplanes.
D. Description
Get access to the left and right MLG Retract Actuator Fuse Pins. Do an inspection of the Retract
Actuator Fuse Pins to identify the part number. If an affected pin is found, replace the pin. If an affected
pin is not found, no further action is required at that pin location.
Group 1:
Revision 2 - No more work is necessary on the airplane(s) that have replaced 112W1769-1 Retract
Actuator Fuse Pins with 112W1769-3 Retract Actuator Fuse Pins in accordance with the Original Issue
or Revision 1 of this service bulletin and have not replaced 112W1769-3 Retract Actuator Fuse Pins
with 112W1769-1 Retract Actuator Fuse Pins.
Group 2:
Revision 2 - Group 2 airplanes, 777-200 and 777-300 airplanes line number 164 through 1027, are
added to this service bulletin effectivity. Due to an interchangeability error in the Illustrated Parts Catalog
(IPC), it is possible that 112W1769-1 Retract Actuator Fuse Pins were installed on 777-200 and 777-300
airplanes line number 164 through 1027.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
731, 741777-200, 777-300
E. Compliance
Group 1:
Federal Aviation Administration (FAA) Airworthiness Directive AD 2012-12-08 is related to this service
bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
15 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 16

Group 2:
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Accomplish Part 1 and Part 2 as required in Table 1 below in accordance with Paragraph 3.,
Accomplishment Instructions. Part 2 only affects airplanes with any 112W1769-1 MLG Retract Actuator
Fuse Pin installed.
NOTE: 1. The conditions, actions and compliance times below are based on flight cycles on each pin
since new, not flight cycles of the airplane on which the pin is installed.
2. The effective date of AD 2012-12-08 is July 30, 2012.
Evaluate the conditions and actions for the left and right Main Landing Gear (MLG) Retract Actuator
Fuse Pin separately.
Group 1:
Table 1: Inspection and Replacement of Retract Actuator Fuse Pin
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 18 months after the effec-
tive date of AD 2012-12-08.
Inspect the pin in accor-
dance with Part 1 - MLG
Retract Actuator Fuse Pin
Part Number Inspection.
All Airplanes
--No further action is re-
quired for that fuse pin
location. (a)
Condition 1: 112W1769-3
MLG Retract Actuator Fuse
Pin Installed.
-Within 18 months after the effec-
tive date of AD 2012-12-08.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2A: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
greater than 10,000 flight
cycles (FC).
-Within 18
months after the
effective date of
AD 2012-12-08.
Before 10,000
total flight-cy-
cles on the pin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2B: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
8,000 to 10,000 FC.
-Within 24
months after the
effective date of
AD 2012-12-08.
Before 8,000 to-
tal flight-cycles
on the pin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2C: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with less
than 8,000 FC.
(a) The 112W1769-3 MLG Retract Actuator Fuse Pin is a safe life limited part. Refer to 777 MPD Section 9
for the safe life limits.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
16 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 17

Group 2:
Table 2: Inspection and Replacement of Retract Actuator Fuse Pin
Repeat Interval
(Not to Exceed)
Compliance Time (Whichever
Occurs Later)
ActionCondition
-Within 18 months after the Revi-
sion 2 date of this service bulletin.
Inspect the pin in accor-
dance with Part 1 - MLG
Retract Actuator Fuse Pin
Part Number Inspection.
All Airplanes
--No further action is re-
quired for that fuse pin
location. (a)
Condition 1: 112W1769-3
MLG Retract Actuator Fuse
Pin Installed.
-Within 18 months after the Revi-
sion 2 date of this service bulletin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2A: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
greater than 10,000 flight
cycles (FC).
-Within 18
months after the
Revision 2 date
of this service
bulletin.
Before 10,000
total flight-cy-
cles on the pin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2B: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
8,000 to 10,000 FC.
-Within 24
months after the
Revision 2 date
of this service
bulletin.
Before 8,000 to-
tal flight-cycles
on the pin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2C: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with less
than 8,000 FC.
(a) The 112W1769-3 MLG Retract Actuator Fuse Pin is a safe life limited part. Refer to 777 MPD Section 9
for the safe life limits.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
Group 1:
In addition, the Manager of the FAA Seattle Aircraft Certification Office approves accomplishment of
the inspection and replacement defined in this service bulletin as an alternative method of compliance
to the inspection and replacement requirements of paragraph (g) of AD 2012-12-08. All provisions of
AD 2012-12-08 that are not specifically referenced in the above statement remain fully applicable and
must be complied with accordingly.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
17 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 18

G. Manpower
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.751.502Open Access
0.250.251FIGURE 1
0.250.251FIGURE 2
0.500.501FIGURE 3
0.500.501FIGURE 4
0.751.502Close Access
3.004.50TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
- 3628.0- 2.7All
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Letter 777-SL-57-011
b. Boeing Service Related Problem (SRP) 777-SRP-57-0226
c. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2012-12-08
d. 777 Aircraft Maintenance Manual (AMM) 06-44-00, 32-00-15, 32-00-30, 32-11-01
e. 777 Fleet Team Digest (FTD) 57-08005
f. 777 Maintenance Planning Data (MPD) Section 9
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
Installation - Main Landing Gear161W0000
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
18 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 19

This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
K. Publications Affected
1. Publications:
Chapter-SectionPublication
32-11777 Illustrated Parts Catalog
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
19 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 20

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
20 of 34
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 21

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary for Each Airplane as shown
below. Operators are encouraged to share schedule requirements with Boeing for incorporation of the
service bulletin. The parts are subject to the terms and conditions of the Boeing standard purchase
order acknowledgment. Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of the
Revision 2 date of
this Service Bul-
letin (US Dollars)
ROLT as of the Re-
vision 2 date of this
Service Bulletin
(Calendar Days)
NamePart Number
$700.00561MLG Retract Actuator Fuse Pin112W1769-3
B. Industry Support Information
Boeing warranty remedies are not available for the inspection, and/or repair procedures given in this
service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NotesExisting Part
Number
NameQTYNew Part Number
(a) (b)
(c)
112W1769-1MLG Retract Actua-
tor Fuse Pin
2112W1769-3
(a) Discard the existing part.
(b) This part is used in production.
(c) You cannot use the existing part to replace the new or changed part.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
21 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 22

2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number /
Specification
(a)Corrosion Inhibiting Material-BMS3-27 (BMS3-
38 Optional)
Pin, Cotter2BACP18BC03A12P
(a) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
22 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 23

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. This note has been deleted.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
5. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
6. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
The removed part can be discarded if a new or serviceable part is installed.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
23 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 24

B. WORK INSTRUCTIONS
1. Install the Main Landing Gear (MLG) downlock pins. Refer to 777 AMM 32-00-30 as an accepted
procedure.
2. Install the MLG safety pins. Refer to 777 AMM 32-00-15 as an accepted procedure.
3. Open the following access panels on the left and right wing. Refer to 777 AMM 06-44-00 as an
accepted procedure.
– 551DB - Inboard Fixed Trailing Edge Panel
– 651DB - Inboard Fixed Trailing Edge Panel
4. Do Part 1 - MLG Retract Actuator Fuse Pin Part Number Inspection.
a. Condition 1: 112W1769-3 MLG Retract Actuator Fuse Pin installed.
(1) No further action is required for that fuse pin location.
b. Condition 2: 112W1769-1 MLG Retract Actuator Fuse Pin installed.
(1) Determine the total flight cycles on the MLG Retract Actuator Fuse Pin since new.
(2) Do Part 2 - MLG Retract Actuator Fuse Pin Replacement within the compliance time in
accordance with Paragraph 1.E., Compliance Condition 2A, 2B or 2C for that fuse pin
location.
(3) No further action is required for that fuse pin location.
5. Close the following access panels on the left and right wing. Refer to 777 AMM 06-44-00 as an
accepted procedure.
– 551DB - Inboard Fixed Trailing Edge Panel
– 651DB - Inboard Fixed Trailing Edge Panel
6. Remove the MLG safety pins. Refer to 777 AMM 32-00-15 as an accepted procedure.
7. Remove the Main Landing Gear (MLG) downlock pins. Refer to 777 AMM 32-00-30 as an accepted
procedure.
8. Put the airplane back to a serviceable condition.
Part 1 - MLG Retract Actuator Fuse Pin Part Number Inspection
1. Inspect the MLG Retract Actuator Fuse Pins to determine the part numbers in accordance with
FIGURE 1 for the left MLG and FIGURE 2 for the right MLG. As an alternative, a review of the
maintenance or delivery records can be used if the part number of the installed MLG Retract
Actuator Fuse Pin can be positively determined.
Part 2 - MLG Retract Actuator Fuse Pin Replacement
1. Replace the 112W1769-1 MLG Retract Actuator Fuse Pin in accordance with FIGURE 3 for the
left MLG and FIGURE 4 for the right MLG.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2: May 02, 2013
24 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 25 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
- 600 F
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
ACCESS PANEL
551DB
FWD
1742803
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 1 OF 2)
Original Issue: February 05, 2009
Revision 2 May 02, 2013  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-32-0083
Work - See page 1 for details.  25 of 34

### Page 26

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each component.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
to determine the part
number which is lo-
cated on the head of
the pin.
1112W1769Retract Actuator Fuse
Pin
Inspect1
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
26 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 27 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
FWD
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
'ACCESS PANEL
651DB
FWD
1742806
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 1 OF 2)
Original Issue: February 05, 2009
Revision 2 May 02, 2013  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-32-0083
Work - See page 1 for details.  27 of 34

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each component.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
to determine the part
number which is lo-
cated on the head of
the pin.
1112W1769Retract Actuator Fuse
Pin
Inspect1
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
28 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 29 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
- 600 F
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
FWD
ACCESS PANEL
551DB
1742866
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 1 OF 3)
Original Issue: February 05, 2009
Revision 2 May 02, 2013  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-32-0083
Work - See page 1 for details.  29 of 34

### Page 30

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each component.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure.
Keep washers and
nut.
1112W1769-1Retract Actuator Fuse
Pin
Remove1
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure. A
new or overhauled
pin is acceptable.
1112W1769-3Retract Actuator Fuse
Pin
Install (New)2
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
30 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 31

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
lightly coating the
thread group of the
pin and the washer
faces.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Apply3
Tighten nut to 15-25
in-lbs over maximum
run on torque.
1-NutInstall (Kept)4
to the nearest
castellation to install
the cotter pin.
1-NutLoosen5
1BACP18BC03A12PCotter PinInstall (New)6
Wipe off all excess
material.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Remove7
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
31 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 32 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
FWD
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
ACCESS PANEL
651DB  FWD
1742910
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 1 OF 3)
Original Issue: February 05, 2009
Revision 2 May 02, 2013  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-32-0083
Work - See page 1 for details.  32 of 34

### Page 33

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each component.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure.
Keep washers and
nut.
1112W1769-1Retract Actuator Fuse
Pin
Remove1
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure. A
new or overhauled
pin is acceptable.
1112W1769-3Retract Actuator Fuse
Pin
Install (New)2
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 2 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
33 of 34
BOEING SERVICE BULLETIN 777-32-0083

### Page 34

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
lightly coating the
thread group of the
pin and the washer
faces.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Apply3
Tighten nut to 15-25
in-lbs over max run
on torque.
1-NutInstall (Kept)4
to the nearest
castellation to install
the cotter pin.
1-NutLoosen5
-BACP18BC03A12PCotter PinInstall (New)6
Wipe off all excess
material.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Remove7
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 2 May 02, 2013
34 of 34
BOEING SERVICE BULLETIN 777-32-0083

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
