# Boeing Special Attention Service Bulletin 777-32-0083: U.S. DOT/FAA - Boeing Service Bulletin - SB-777-32-0083-01

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2011-1412; AD 2012-12-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 777-32-0083](https://openairdocs.org/service-documents/boeing/sb-777-32-0083.md)
- Title as filed: U.S. DOT/FAA - Boeing Service Bulletin - SB-777-32-0083-01
- Pages: 30
- PDF: https://openairdocs.org/files/sha256/a7/8b/a78bc602c2dec7fbd505f6f53a4b6827efdb314ce36997f9059d7e8186a299a4
- Page: https://openairdocs.org/service-documents/boeing/sb-777-32-0083/file/a78bc602c2de

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-32-0083
Original Issue: February 05, 2009
Revision 1: February 17, 2011
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2009 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P.O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the
Boeing livery are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
1 of 30
2.0

### Page 2

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
2 of 30
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 2
B. Concurrent Requirements ...................................... 1 2
C. Reason ................................................ 1 3
D. Description .............................................. 1 3
E. Compliance .............................................. 1 3
F. Approval ............................................... 1 4
G. Manpower .............................................. 1 5
H. Weight and Balance Changes .................................... 1 5
I. Electrical Load Data ......................................... 1 5
J. References .............................................. 1 5
1. Existing Data .......................................... 1 5
2. Data supplied with this Service Bulletin ............................ 1 5
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 1 5
K. Publications Affected ........................................ 1 6
L. Interchangeability and Intermixability of Parts ........................... 1 6
2. MATERIAL INFORMATION ........................................ 1 7
A. Material - Price and Availability ................................... 1 7
B. Industry Support Information .................................... 1 7
C. Parts Necessary For Each Airplane ................................. 1 7
1. Kits/Parts ............................................ 1 7
2. Parts and Materials Supplied by the Operator ........................ 1 8
3. Parts Modified and Reidentified ................................ 1 8
4. Parts Removed and Not Replaced .............................. 1 8
D. Parts Necessary to Change Spares ................................. 1 8
E. Special Tooling - Price and Availability ............................... 1 8
F. Special Tooling Necessary to do this Service Bulletin ....................... 1 8
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 1 9
A. GENERAL INFORMATION ..................................... 1 9
B. WORK INSTRUCTIONS ....................................... 2 0
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION ................ 2 1
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION ............... 2 3
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT .............. 2 5
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT ............. 2 8
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
3 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 4

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
4 of 30
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 5

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 777-32-0083Original Issue: February 05, 2009
Revision 1: February 17, 2011
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on the airplane(s) changed in accordance with the original issue of this service
bulletin.
REASON FOR REVISION
This revision is sent to add an optional material for the Corrosion Inhibiting Material.
These sections were changed:
1. In Paragraph 2.A., Material - Price and Availability, updated table to current standards.
2. In Paragraph 2.C.2., Parts and Materials Supplied by the Operator, added BMS3-38 as optional to BMS3-27
in Part Number Specification column.
3. In Paragraph 3.A., General Information, added Note 5, 6, 8 and 9 to the note list.
4. In Figure 3, step 3, added BMS3-38 as optional to BMS3-27 in Identification column.
5. In Figure 3, step 7, added BMS3-38 as optional to BMS3-27 in Identification column.
6. In Figure 4, step 3, added BMS3-38 as optional to BMS3-27 in Identification column.
7. In Figure 4, step 7, added BMS3-38 as optional to BMS3-27 in Identification column.
The data given in Information Notice 777-32-0083 IN 01 is included in this revision.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
5 of 30

### Page 6

REVISION HISTORY
February 05, 2009Original Issue:
February 17, 2011Revision 1:
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
6 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 7

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 777-32-0083Original Issue: February 05, 2009
Revision 1: February 17, 2011
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will find and replace 112W1769-1 Retract Actuator Fuse Pins. The
112W1769-1 Retract Actuator Fuse Pins have been found to crack and fail earlier than the previously determined
safe life limit of the pins. A fractured Retract Actuator Fuse Pin can cause the main landing gear (MLG) to extend
without restriction and attempt to lock into position under high dynamic loads. Unrestricted MLG extension could
cause structural damage to the side and drag brace lock assemblies, leading to unlocked drag and/or side
braces which could result in landing gear collapse during touchdown, rollout or taxi.
One operator reported that a right MLG 112W1769-1 pin sheared during normal flight operations. The failure
occurred on a pin with 10,874 flight cycles. The left MLG pin was also inspected and was found to be cracked.
Examination of the sheared pin concluded that the cracking was due to fatigue. Three other pins that were
reported to have cracks had between 10,000 and 11,000 flight cycles.
This service bulletin provides instructions to inspect the left and right MLG for 112W1769-1 Retract Actuator
Fuse Pins and to replace the affected pins with 112W1769-3 pins.
Boeing Service Related Problem (SRP) 777-SRP-57-0226 is related to this service bulletin.
Boeing Service Letter (SL) 777-SL-57-011 is related to this service bulletin.
Boeing Fleet Team Digest Article (FTD) 777 FTD 57-08005 is related to this service bulletin.
ACTION
Get access to the left and right MLG Retract Actuator Fuse Pins. Do an inspection of the Retract Actuator Fuse
Pins to identify the part number. If an affected pin is found, replace the pin. If an affected pin is not found, no
further action is required at that pin location.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
7 of 30

### Page 8

EFFECTIVITY
777-200 and 777-300 Airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection, and/or repair procedures given in this service
bulletin.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
3.004.50All
MATERIAL INFORMATION
Boeing and Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
8 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 9 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
GET ACCESS TO THE LEFT AND
RIGHT MLG RETRACT ACTUATOR I
FUSE PINS THROUGH PANEL
551DB AND 651DB.
- 600 F
_EFT MLG SHOWN
RIGHT MLG OPPOSITI
DO AN INSPECTION OF THE RETRACT ACTUATOR
FUSE PINS TO IDENTIFY THE PART NUMBER. IF AN
AFFECTED PIN IS FOUND, REPLACE THE PIN. IF AN
AFFECTED PIN IS NOT FOUND, NO FURTHER ACTION
IS REQUIRED FOR THAT PIN LOCATION.  FWD
1742524
Original Issue: February 05, 2009
Revision 1: February 17, 2011  777-32-0083
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.  9 of 30

### Page 10

BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
10 of 30
BOEING SERVICE BULLETIN 777-32-0083
BLANK PAGE

### Page 11

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-32-0083
Original Issue: February 05, 2009
Revision 1: February 17, 2011
ATA System: 3211
SUBJECT: LANDING GEAR - Main Landing Gear - Retract Actuator Fuse Pin Inspection and
Replacement
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
Refer to Service Bulletin Index Document D624W001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
777 Airplanes with line numbers 1-163.-1
Airplane Models:
777-200, 777-300
GroupVariable Number
1WA001 - WA017
1WA076 - WA080
1WA086 - WA093
1WA101 - WA104
1WA116 - WA119
1WA131 - WA137
1WA171 - WA175
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
11 of 30

### Page 12

GroupVariable Number
1WA196 - WA198
1WA206 - WA211
1WA221 - WA223
1WA231 - WA232
1WB001 - WB014
1WB051 - WB068
1WB101 - WB104
1WB121 - WB125
1WB131 - WB133
1WB151 - WB153
1WB161 - WB169
1WB181 - WB186
1WB231 - WB234
1WB271 - WB272
1WB276 - WB286
1WB306 - WB307
1WB311 - WB313
1WB336
1WB371
1WB501 - WB504
1WB531 - WB534
1WB551 - WB552
1WB591 - WB592
1WB601
2. Spares Affected
None.
B. Concurrent Requirements
None.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
12 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 13

C. Reason
Accomplishment of this service bulletin will find and replace 112W1769-1 Retract Actuator Fuse Pins.
The 112W1769-1 Retract Actuator Fuse Pins have been found to crack and fail earlier than the previously
determined safe life limit of the pins. A fractured Retract Actuator Fuse Pin can cause the main landing
gear (MLG) to extend without restriction and attempt to lock into position under high dynamic loads.
Unrestricted MLG extension could cause structural damage to the side and drag brace lock assemblies,
leading to unlocked drag and/or side braces which could result in landing gear collapse during
touchdown, rollout or taxi.
One operator reported that a right MLG 112W1769-1 pin sheared during normal flight operations. The
failure occurred on a pin with 10,874 flight cycles. The left MLG pin was also inspected and was found
to be cracked. Examination of the sheared pin concluded that the cracking was due to fatigue. Three
other pins that were reported to have cracks had between 10,000 and 11,000 flight cycles.
This service bulletin provides instructions to inspect the left and right MLG for 112W1769-1 Retract
Actuator Fuse Pins and to replace the affected pins with 112W1769-3 pins.
Boeing Service Related Problem (SRP) 777-SRP-57-0226 is related to this service bulletin.
Boeing Service Letter (SL) 777-SL-57-011 is related to this service bulletin.
Boeing Fleet Team Digest Article (FTD) 777 FTD 57-08005 is related to this service bulletin.
D. Description
Get access to the left and right MLG Retract Actuator Fuse Pins. Do an inspection of the Retract
Actuator Fuse Pins to identify the part number. If an affected pin is found, replace the pin. If an affected
pin is not found, no further action is required at that pin location.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
731, 741777-200, 777-300
E. Compliance
Accomplish Part 1 and Part 2 as required in Table 1 below in accordance with Paragraph 3.,
Accomplishment Instructions.
NOTE: 1. The conditions, actions and compliance times below are based on flight cycles on each pin
since new, not flight cycles of the airplane on which the pin is installed.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
13 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 14

Table 1: Inspection and Replacement of Retract Actuator Fuse Pin
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 6 months
after the Date of
the Original Issue
of this Service Bul-
letin.
Inspect the pin in accor-
dance with Part 1 - MLG
Retract Actuator Fuse Pin
Part Number Inspection.
All Airplanes
--No further action is re-
quired for that fuse pin
location. (a)
Condition 1: 112W1769-3
MLG Retract Actuator Fuse
Pin Installed.
-Within 6 months
after the Date of
the Original Issue
of this Service Bul-
letin.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2A: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
greater than 10,000 flight
cycles (FC).
-Before 10,000 FC
on the pin or within
12 months after the
Date of the Original
Issue of this Ser-
vice Bulletin,
whichever occurs
later.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2B: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with
8,000 to 10,000 FC.
-Before 8,000 FC
on the pin or within
24 months after the
Date of the Original
Issue of this Ser-
vice Bulletin,
whichever occurs
later.
Replace the pin in accor-
dance with Part 2 - MLG
Retract Actuator Fuse Pin
Replacement. (a)
Condition 2C: 112W1769-
1 MLG Retract Actuator
Fuse Pin installed with less
than 8,000 FC.
(a) The 112W1769-3 MLG Retract Actuator Fuse Pin is a safe life limited part. Refer to 777
MPD Section 9 for the safe life limits.
F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
14 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 15

G. Manpower
Elapsed HoursTask HoursNumber of Per-
sons
Task
0.751.502Open Access
0.250.251FIGURE 1
0.250.251FIGURE 2
0.500.501FIGURE 3
0.500.501FIGURE 4
0.751.502Close Access
3.004.50TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
- 3628.0- 2.7All
I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. Boeing Service Letter 777-SL-57-011
b. Boeing Service Related Problem (SRP) 777-SRP-57-0226
c. 777 Aircraft Maintenance Manual (AMM) 06-44-00, 32-00-15, 32-00-30, 32-11-01
d. 777 Fleet Team Digest (FTD) 57-08005
e. 777 Maintenance Planning Data (MPD) Section 9
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Installation - Main Landing Gear161W0000
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
15 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 16

This drawing was used to prepare this service bulletin. This drawing is not necessary to make the
specified changes, and is not supplied with this service bulletin. This drawing may not be applicable
to all airplane configurations or operators.
K. Publications Affected
Chapter-SectionPublication
32-11777 Illustrated Parts Catalog
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
16 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 17

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the parts shown in Paragraph 2.C., Parts Necessary for Each Airplane as shown
below. Operators are encouraged to share schedule requirements with Boeing for incorporation of the
service bulletin. The parts are subject to the terms and conditions of the Boeing standard purchase
order acknowledgment. Prices are in United States Dollars. Terms: Net 30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPON-
DER AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFOR-
MATION
Unit Price as of the
orignal issue date
of this Service Bul-
letin (US Dollars)
ROLT as of
the original
issues date
of this Ser-
vice Bulletin
(Calendar
Days)
NamePart Number
$769.00588MLG Retract Actuator Fuse Pin112W1769-3
B. Industry Support Information
Boeing warranty remedies are not available for the inspection, and/or repair procedures given in this
service bulletin.
C. Parts Necessary For Each Airplane
1. Kits/Parts
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NotesExisting Part
Number
NameQTYNew Part Number
(a) (b)
(c)
112W1769-1MLG Retract Actua-
tor Fuse Pin
2112W1769-3
(a) Discard the existing part.
(b) This part is used in production.
(c) You cannot use the existing part to replace the new or changed part.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
17 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 18

2. Parts and Materials Supplied by the Operator
NotesNameQTYPart Number /
Specification
(a)Corrosion Inhibiting Material-BMS3-27 (BMS3-
38 Optional)
Pin, Cotter2BACP18BC03A12P
(a) See the Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
18 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 19

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s)
give the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
5. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
6. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
7. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
8. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
9. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
The removed part can be discarded if a new or serviceable part is installed.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
19 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 20

B. WORK INSTRUCTIONS
1. Install the Main Landing Gear (MLG) downlock pins. Refer to 777 AMM 32-00-30 as an accepted
procedure.
2. Install the MLG safety pins. Refer to 777 AMM 32-00-15 as an accepted procedure.
3. Open the following access panels on the left and right wing. Refer to 777 AMM 06-44-00 as an
accepted procedure.
– 551DB - Inboard Fixed Trailing Edge Panel
– 651DB - Inboard Fixed Trailing Edge Panel
4. Do Part 1 - MLG Retract Actuator Fuse Pin Part Number Inspection.
a. Condition 1: 112W1769-3 MLG Retract Actuator Fuse Pin installed.
(1) No further action is required for that fuse pin location.
b. Condition 2: 112W1769-1 MLG Retract Actuator Fuse Pin installed.
(1) Determine the total flight cycles on the MLG Retract Actuator Fuse Pin since new.
(2) Do Part 2 - MLG Retract Actuator Fuse Pin Replacement within the compliance time in
accordance with Paragraph 1.E., Compliance Condition 2A, 2B or 2C for that fuse pin
location.
(3) No further action is required for that fuse pin location.
5. Close the following access panels on the left and right wing. Refer to 777 AMM 06-44-00 as an
accepted procedure.
– 551DB - Inboard Fixed Trailing Edge Panel
– 651DB - Inboard Fixed Trailing Edge Panel
6. Remove the MLG safety pins. Refer to 777 AMM 32-00-15 as an accepted procedure.
7. Remove the Main Landing Gear (MLG) downlock pins. Refer to 777 AMM 32-00-30 as an accepted
procedure.
8. Put the airplane back into serviceable condition.
Part 1 - MLG Retract Actuator Fuse Pin Part Number Inspection
1. Inspect the MLG Retract Actuator Fuse Pins to determine the part numbers in accordance with
FIGURE 1 for the left MLG and FIGURE 2 for the right MLG. As an alternative, a review of the
maintenance or delivery records can be used if the part number of the installed MLG Retract
Actuator Fuse Pin can be positively determined.
Part 2 - MLG Retract Actuator Fuse Pin Replacement
1. Replace the MLG Retract Actuator Fuse Pin in accordance with FIGURE 3 for the left MLG and
FIGURE 4 for the right MLG.
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1: February 17, 2011
20 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 21 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
- 600 F
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
ACCESS PANEL
551DB
FWD
1742803
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 1 OF 2)
Original Issue: February 05, 2009
Revision 1 February 17, 2011  BOEING PROPRIETARY -  777-32-0083
Copyright © Unpublished Work - See page 1 for details.  21 of 30

### Page 22

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
to determine the part
number which is lo-
cated on the head of
the pin.
1112W1769Retract Actuator Fuse
Pin
Inspect1
FIGURE 1: LEFT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
22 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 23 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
FWD
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
'ACCESS PANEL
651DB
FWD
1742806
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 1 OF 2)
Original Issue: February 05, 2009
Revision 1 February 17, 2011  BOEING PROPRIETARY -  777-32-0083
Copyright © Unpublished Work - See page 1 for details.  23 of 30

### Page 24

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
to determine the part
number which is lo-
cated on the head of
the pin.
1112W1769Retract Actuator Fuse
Pin
Inspect1
FIGURE 2: RIGHT MLG RETRACT ACTUATOR FUSE PIN INSPECTION
(SHEET 2 OF 2)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
24 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 25 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
- 600 F
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
FWD
ACCESS PANEL
551DB
1742866
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 1 OF 3)
Original Issue: February 05, 2009
Revision 1 February 17, 2011  BOEING PROPRIETARY -  777-32-0083
Copyright © Unpublished Work - See page 1 for details.  25 of 30

### Page 26

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure.
Keep washers and
nut.
1112W1769-1Retract Actuator Fuse
Pin
Remove1
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure. A
new or overhauled
pin is acceptable.
1112W1769-3Retract Actuator Fuse
Pin
Install (New)2
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
26 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 27

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
lightly coating the
thread group of the
pin and the washer
faces.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Apply3
Tighten nut to 15-25
in-lbs over maximum
run on torque.
1-NutInstall (Kept)4
to the nearest
castellation to install
the cotter pin.
1-NutLoosen5
1BACP18BC03A12PCotter PinInstall (New)6
Wipe off all excess
material.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Remove7
FIGURE 3: LEFT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
27 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 28 (OCR)

BOEING SERVICE BULLETIN 777-32-0083
FWD
RETRACT
ACTUATOR
FITTING
RETRACT
ACTUATOR
LINK
ACCESS PANEL
651DB  FWD
1742910
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 1 OF 3)
Original Issue: February 05, 2009
Revision 1 February 17, 2011  BOEING PROPRIETARY -  777-32-0083
Copyright © Unpublished Work - See page 1 for details.  28 of 30

### Page 29

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure.
Keep washers and
nut.
1112W1769-1Retract Actuator Fuse
Pin
Remove1
Refer to 777 AMM
32-11-01 as an ac-
cepted procedure. A
new or overhauled
pin is acceptable.
1112W1769-3Retract Actuator Fuse
Pin
Install (New)2
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 2 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
29 of 30
BOEING SERVICE BULLETIN 777-32-0083

### Page 30

MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
lightly coating the
thread group of the
pin and the washer
faces.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Apply3
Tighten nut to 15-25
in-lbs over max run
on torque.
1-NutInstall (Kept)4
to the nearest
castellation to install
the cotter pin.
1-NutLoosen5
-BACP18BC03A12PCotter PinInstall (New)6
Wipe off all excess
material.
-BMS3-27  (BMS3-38
optional)
Corrosion Inhibiting
Material
Remove7
FIGURE 4: RIGHT MLG RETRACT ACTUATOR FUSE PIN REPLACEMENT
(SHEET 3 OF 3)
BOEING PROPRIETARY -
Copyright © Unpublished Work - See page 1 for details.
Original Issue: February 05, 2009
777-32-0083Revision 1 February 17, 2011
30 of 30
BOEING SERVICE BULLETIN 777-32-0083

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
