# Boeing Special Attention Service Bulletin 777-54-0028: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0654; AD 2014-20-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 777-54-0028](https://openairdocs.org/service-documents/boeing/sb-777-54-0028.md)
- Title as filed: U.S. DOT/FAA - SB-777-54-0028-01
- Pages: 49
- PDF: https://openairdocs.org/files/sha256/76/5b/765b93cb652a7d95f1fe33de8fa647f48e607175305577c93d3bec466d7fcc5d
- Page: https://openairdocs.org/service-documents/boeing/sb-777-54-0028/file/765b93cb652a

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-54-0028
Original Issue: May 25, 2012
Revision 1: December 10, 2013
ATA System: 5451
SUBJECT: NACELLES / PYLONS - Nacelle Strut - PW4000 Forward Dry Bay and Forward Engine
Mount Bulkhead - Inspection
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2012 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, KC-10, KC-46, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8, Poseidon and
Boeing liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in
connection with this document unless provided in writing by Boeing.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
1 of 49
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
2 of 49
BOEING SERVICE BULLETIN 777-54-0028
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 3
A. Effectivity ............................................... 1 3
1. Airplanes ............................................ 1 3
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 4
C. Reason ................................................ 1 4
D. Description .............................................. 1 5
E. Compliance .............................................. 1 6
F. Approval ............................................... 1 9
G. Manpower .............................................. 1 9
H. Weight and Balance Changes .................................... 2 0
I. Electrical Load Data ......................................... 2 0
J. References .............................................. 2 0
1. Existing Data: ......................................... 2 0
2. Data Supplied with this Service Bulletin: ........................... 2 1
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 1
K. Publications Affected ........................................ 2 1
L. Interchangeability and Intermixability of Parts ........................... 2 1
M. Software Accomplishment Summary ................................ 2 1
2. MATERIAL INFORMATION ........................................ 2 3
A. Material - Price and Availability ................................... 2 3
B. Industry Support Information .................................... 2 3
C. Parts Necessary for Each Airplane ................................. 2 3
1. Kits/Parts ............................................ 2 3
2. Parts and Materials Supplied by the Operator ........................ 2 3
3. Parts Modified and Reidentified ................................ 2 4
4. Parts Removed and Not Replaced .............................. 2 4
D. Parts Necessary to Change Spares ................................. 2 4
E. Special Tooling - Price and Availability ............................... 2 4
F. Special Tooling Necessary to do this Service Bulletin ....................... 2 4
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 5
A. GENERAL INFORMATION ..................................... 2 5
B. WORK INSTRUCTIONS ....................................... 2 6
FIGURE 1: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - GVI INSPECTION ........... 3 0
FIGURE 2: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - DET INSPECTION .......... 3 2
FIGURE 3: STRUT NO. 1 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC
INSPECTION .......................................... 3 6
FIGURE 4: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - GVI INSPECTION ........... 3 8
FIGURE 5: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - DET INSPECTION .......... 4 0
FIGURE 6: STRUT NO. 2 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC
INSPECTION .......................................... 4 4
APPENDIX A: CLEANING AND REFINISHING OF STRUT FWD DRY BAY DETAILS .......... 4 6
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
3 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 4

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
4 of 49
BOEING SERVICE BULLETIN 777-54-0028
BLANK PAGE

### Page 5

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 777-54-0028Original Issue: May 25, 2012
Revision 1: December 10, 2013
ATA System: 5451
SUBJECT: NACELLES / PYLONS - Nacelle Strut - PW4000 Forward Dry Bay and Forward Engine
Mount Bulkhead - Inspection
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-11-14 is related to this service bulletin.
Airplanes WC587, WC593, WC594, and WC595 were added to the service bulletin effectivity as Group 2
Airplanes. These airplanes should accomplish the initial inspection at the compliance time in accordance with
Paragraph 1.E., Compliance.
No more work is necessary on the airplanes inspected in accordance with the original issue of this service
bulletin. These airplanes should repeat the inspection at the repeat interval in accordance with Paragraph 1.E.,
Compliance.
REASON FOR REVISION
This revision is sent to:
1. Add airplanes WC587, WC593, WC594, and WC595 to the effectivity of this service bulletin as Group
2 Airplanes. Subsequent to the release of this service bulletin it was determined that a production
change that was to be installed on these airplanes that would have terminated the inspections in this
service bulletin could not be installed. Therefore the inspection of these airplanes in accordance with
this service bulletin is required. Group 2 Airplanes are the same as Group 1 Airplanes, except for the
compliance time for the initial inspection.
2. Revise compliance table and work instructions to show that finish restoration is not required until the
repairs are required.
3. Clarify that hydraulic fluid contamination includes hydraulic fluid contamination in its liquid (fluid), vapor,
and/or solid (coked) form.
4. Add optional leveling compound.
5. Add an alternate method of leveling compound repair for small areas that uses sealant and does not
require airplane leveling.
These sections were changed:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
5 of 49

### Page 6

1. Summary:
a. Background - Revise to show hydraulic fluid contamination can be in the form of a liquid (fluid),
vapor, or solid (coke). Revise hydraulic fluid to hydraulic fluid contamination at 4 locations.
b. Action - Revise Part 1 to show hydraulic fluid contamination can be in the form of a liquid (fluid),
vapor, or solid (coke) and blistered and/or peeling primer is a sign of hydraulic fluid contamination.
c. Compliance - Add FAA AD.
2. Planning Information:
a. Paragraph 1.C., Reason:
(1) Revise to show hydraulic fluid contamination can be in the form of a liquid (fluid), vapor, or
solid (coke). Revise hydraulic fluid to hydraulic fluid contamination at 4 locations.
(2) Add Reason for this revision information.
b. Paragraph 1.D., Description:
(1) Revise Part 1 to show hydraulic fluid contamination can be in the form of a liquid (fluid), vapor,
or solid (coke) and blistered and/or peeling primer is a sign of hydraulic fluid contamination.
(2) Add "Compliance Information Related to This Revision".
(3) add Affected Maintenance Zone Table for Group 2 Airplanes.
c. Paragraph 1.E., Compliance:
(1) Add FAA AD.
(2) Revise Table 1, row 1 to limit condition to Group 1 Airplanes.
(3) Add Table 1, row 2 for Group 2 Airplanes. Group 2 Airplanes have initial compliance from
revision 1 date, instead of from the effective date of the AD.
(4) Revise to show hydraulic fluid contamination can be in the form of a liquid (fluid), vapor, or
solid (coke) in multiple locations in Table 1.
(5) Clarify that the compliance time in Table 1, second action for condition 2B is from the time
Condition 2B is found.
(6) Clarify that restore sealant, primer and leveling compound can be accomplished at the same
compliance time as the repair in Table 1, second action for condition 2B.
(7) Clarify that restoration of sealant, primer, and leveling compound can be accomplished at the
same compliance time as the repair in Table 1, first action for condition 2C.
d. Paragraph 1.F., Approval:
(1) Add statement approving this service bulletin as an alternate method of compliance (AMOC)
to FAA AD.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
6 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 7

e. Paragraph 1.J.1., Existing Data:
(1) Add FAA AD.
3. Material Information:
a. Paragraph 2.C.2., Parts and Materials Supplied by the Operator:
(1) Add optional leveling compound. Change finishes to sealant, primer, and leveling compound.
4. Accomplishment Instructions:
a. Paragraph 3.A., General Information - No Changes
b. Paragraph 3.B., Work Instructions:
(1) General Work Instructions:
(a) Revise to show hydraulic fluid contamination can be in the form of a liquid (fluid), vapor,
or solid (coke) in 6 locations.
(b) Move restoration of sealant, primer, and leveling compound from Part 2, Step 4 to the
second action for condition 2B. Move restoration of sealant, primer, and leveling compound
from Part 3, Step 4 to the first action for condition 2C.
(2) Part 1:
(a) Step 3 - Revise to show hydraulic fluid contamination can be in the form of a liquid (fluid),
vapor, or solid (coke).
(3) Part 2:
(a) Delete Step 4 and move restoration of sealant, primer, and leveling compound to the
second action for condition 2B.
(4) Part 3:
(a) Delete Step 4 and move restoration of sealant, primer, and leveling compound to the first
action for condition 2C.
(5) FIGURE 1:
(a) Illustration: No changes.
(b) Step Table:
1) Step 1 - Revise to show hydraulic fluid can be in the form of a liquid (fluid), vapor,
or solid (coke). Revise to show that blistered and/or peeling primer is a sign of
hydraulic fluid contamination.
(6) FIGURE 4:
(a) Illustration: No changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
7 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 8

(b) Step Table:
1) Step 1 - Revise to show hydraulic fluid can be in the form of a liquid (fluid), vapor,
or solid (coke). Revise to show that blistered and/or peeling primer is a sign of
hydraulic fluid contamination.
(7) APPENDIX A:
(a) Illustrations: No changes.
(b) Step Table:
1) Note - Add optional sealant repair.
2) Step 7 - Add optional leveling compound. Refer to optional sealant repair.
3) Step 8 - Add optional leveling compound. Refer to optional sealant repair.
4) Step 9 - Add option to use sealant to repair small areas of leveling compound. The
option does not require the airplane to be leveled.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
May 25, 2012Original Issue:
December 10, 2013Revision 1:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
8 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 9

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 777-54-0028Original Issue: May 25, 2012
Revision 1: December 10, 2013
ATA System: 5451
SUBJECT: NACELLES / PYLONS - Nacelle Strut - PW4000 Forward Dry Bay and Forward Engine
Mount Bulkhead - Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of the inspections in this service bulletin will find hydraulic fluid contamination in its liquid (fluid),
vapor, and/or solid (coked) form in the strut forward dry bay, before the forward engine mount bulkhead fittings
become sufficiently hydrogen embrittled that they can not carry design loads. If hydraulic fluid contamination is
on the titanium forward engine mount bulkhead fittings, hydrogen embrittlement of the fittings can occur. When
the forward engine mount bulkhead fitting becomes sufficiently hydrogen embrittled it cannot carry design load
and loses limit load capability that can lead to the loss or departure of an engine. Similarly, hydrogen embrittlement
of the fittings can cause through crack formation across the fitting. Such through cracks might not contain an
engine fire and allow the fire to breach into the strut. The forward engine mount bulkhead fitting does not have
fire detection or fire suppression capability. Thus, a fire breaching the forward engine mount bulkhead fitting
can lead to an uncontained fire in the strut.
One operator has reported 5 airplanes with hydraulic fluid residue in the strut forward dry bay. The airplanes
had approximately 9,900 to 29,000 flight-cycles and 13,000 to 33,300 flight-hours. The forward engine mount
bulkhead fittings are made from titanium and are located near the hot engine core of the engine where
temperatures can exceed 270 degrees Fahrenheit. The presence of hydraulic fluid contamination and temperature
above 270 degrees Fahrenheit can result in hydrogen embrittlement of the titanium forward engine mount
bulkhead fittings. If the forward engine mount bulkhead fittings become sufficiently hydrogen embrittled, they
may not be able to carry design loads. It is believed that hydraulic fluid contamination is entering the dry bay
through the condensate drain line. The condensate drain connects to the system disconnect box drain lines,
which drains hydraulic fluid and fuel from the system disconnect box. The system disconnect box drain hose
can clog due to hydraulic fluid coking in the drain lines. This allows hydraulic fluid to back up into strut forward
dry bay through the condensate drain line. Boeing Service Bulletin 777-54-0027 addresses blockage of the strut
forward drain lines. If a fitting becomes embrittled, fitting and/or strut replacement may be required. If the fitting
becomes sufficiently brittle, it may not be able to carry design loads.
Inspection of the strut forward dry bay for the presence of hydraulic fluid contamination will help prevent hydrogen
embrittlement of the titanium forward engine mount bulkhead fittings.
Boeing Fleet Team Digest (FTD) 777 FTD 54-11001 is related to this service bulletin.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
9 of 49

### Page 10

Boeing Service Related Problem (SRP) 777-SRP-54-0138 is related to this service bulletin.
This table is provided to operators for planning purposes only. Refer to the applicable sections for more
information.
ReferenceAffectedPlanning Data
Paragraph 1.A.2., Spares AffectedNoSpares Affected
Paragraph 1.E., ComplianceYesAD Related
Paragraph 1.H., Weight and Balance ChangesNoWeight and Balance Change
Paragraph 1.I., Electrical Load DataNoElectrical Load Changed
Paragraph 1.K., Publications AffectedNoPublications Affected
Paragraph 1.K., Publications AffectedNoAirplane Flight Operations Affected (Flight Crew
Operations Manual and/or FAA Approved Air-
plane Flight Manual)
Paragraph 2.C.1., Kits/PartsNoKits/Parts Required
Paragraph 2.C.2., Parts and Materials Supplied
by the Operator
NoOperator Supplied Material
Paragraph 2.F., Special Tooling Necessary to
do this Service Bulletin
NoSpecial Tooling Required
ACTION
Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
Open the thrust reverser. Remove the strut forward dry bay access door. Do a General Visual Inspection (GVI)
for hydraulic fluid contamination in its liquid (fluid), vapor, and/or solid (coked) form. Blistered and/or peeling
primer is a sign of hydraulic fluid contamination and the strut forward dry bay is contaminated. Install the strut
forward dry bay access door. Close the thrust reverser.
Part 2 - Strut Forward Dry Bay Interior DET Inspection
Open the thrust reverser. Remove the strut forward dry bay access door. Do a Detailed Inspection (DET) of the
interior of the strut forward dry bay for hydraulic fluid coking, heat discoloration, damage to sealant and primer,
damage to leveling compound, cracks; and etching or pitting. Clean and restore sealant, primer, and leveling
compound of the detail parts in the strut forward dry bay if missing, blistered, peeling, or damaged. Check drain
lines and clean or replace drain lines as required. Install the strut forward dry bay access door. Close the thrust
reverser.
Part 3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection
Open the thrust reverser. Remove the strut forward dry bay access door. Do a DET and High Frequency Eddy
Current (HFEC) inspection of the strut forward engine mount bulkhead upper and lower fittings for cracks, and
etching or pitting. Clean and restore sealant, primer, and leveling compound of the detail parts in the strut forward
dry bay if missing, blistered, peeling, or damaged. Check drain lines and clean or replace drain lines as required.
Install the strut forward dry bay access door. Close the thrust reverser.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
10 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 11

EFFECTIVITY
777-200 and -300 Airplanes powered by PW4000 Engines. Refer to Paragraph 1.A.1., Airplanes, for the list of
affected airplanes.
COMPLIANCE
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-11-14 is related to this service bulletin.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of June 15, 2011. Please refer to Paragraph
2.B., Industry Support Information.
MANPOWER
Elapsed HoursTotal Task Hours
3.005.00Part 1 - Strut Forward Dry Bay Hydraulic
Fluid Contamination GVI Inspection
12.5017.00Part 2 - Strut Forward Dry Bay Interior
DET Inspection
12.5017.00Part 3 - Strut Forward Engine Mount
Bulkhead Fitting DET and HFEC Inspec-
tion
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
11 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 12 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
432AR (STRUT NO.1)
442AR (STRUT NO.2)
LEFT STRUT
FORWARD ENGINE
MOUNT BULKHEAD
UPPER FITTING
MOLOWER FITTING
PART 1:
DO A GVI FOR HYDRAULIC FLUID
CONTAMINATION
PART 2:
DO A DET FOR HYDRAULIC FLUID
COKING, HEAT DISCOLORATION, DAMAGE
TO SEALANT AND PRIMER, DAMAGE TO
LEVELING COMPOUND, CRACKS, AND
ETCHING OR PITTING.
PART 3:
DO A DET AND HFEC OF THE UPPER
AND LOWER ENGINE MOUNT
BULKHEAD FITTINGS FOR CRACKS  FWD
AND ETCHING OR PITTING.
STRUT FORWARD DRY BAY
(STRUT NO. 1 SHOWN; STRUT NO. 2 OPPOSITE)  CONDENSATE
DRAIN  2125481
Original Issue: May 25, 2012
Revision 1: December 10, 2013  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-54-0028
Work - See page 1 for details.  12 of 49

### Page 13

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-54-0028
Original Issue: May 25, 2012
Revision 1: December 10, 2013
ATA System: 5451
SUBJECT: NACELLES / PYLONS - Nacelle Strut - PW4000 Forward Dry Bay and Forward Engine
Mount Bulkhead - Inspection
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplane(s) shown below.
Refer to Service Bulletin Index D624W001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
777-200 and -300 Airplanes line numbers 2 through 1027 powered
by Pratt and Whitney (PW) 4000 Engines.
-1
777-200 and -300 Airplanes line numbers 1090 through 1117 powered
by Pratt and Whitney (PW) 4000 Engines.
-2
Airplane Models:
777-200, 777-300
GroupVariable Number
1WA002 - WA017
1WA131 - WA137
1WA171 - WA175
1WA206 - WA212
1WA221 - WA223
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
13 of 49

### Page 14

GroupVariable Number
1WA231 - WA232
1WA241 - WA250
1WA261 - WA266
1WA281 - WA283
1WA301 - WA304
1WB051 - WB088
1WB131 - WB148
1WB151 - WB155
1WB366 - WB368
1WB481 - WB484
1WB531 - WB537
1WB551 - WB554
1WB591 - WB597
1WC111 - WC120
1WC371 - WC374
1WC506 - WC508
1WC581
1WC586
2WC587
1WC591 - WC592
2WC593 - WC595
2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
Accomplishment of the inspections in this service bulletin will find hydraulic fluid contamination in its
liquid (fluid), vapor, or solid (coked) form in the strut forward dry bay, before the forward engine mount
bulkhead fittings become sufficiently hydrogen embrittled that they can not carry design loads. If hydraulic
fluid contamination is on the titanium forward engine mount bulkhead fittings, hydrogen embrittlement
of the fittings can occur. When the forward engine mount bulkhead fitting becomes sufficiently hydrogen
embrittled it cannot carry design load and loses limit load capability that can lead to the loss or departure
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
14 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 15

of an engine. Similarly, hydrogen embrittlement of the fittings can cause through crack formation across
the fitting. Such through cracks might not contain an engine fire and allow the fire to breach into the
strut. The forward engine mount bulkhead fitting does not have fire detection or fire suppression
capability. Thus, a fire breaching the forward engine mount bulkhead fitting can lead to an uncontained
fire in the strut.
One operator has reported 5 airplanes with hydraulic fluid residue in the strut forward dry bay. The
airplanes had approximately 9,900 to 29,000 flight-cycles and 13,000 to 33,300 flight-hours. The forward
engine mount bulkhead fittings are made from titanium and are located near the hot engine core of the
engine where temperatures can exceed 270 degrees Fahrenheit. The presence of hydraulic fluid
contamination and temperature above 270 degrees Fahrenheit can result in hydrogen embrittlement
of the titanium forward engine mount bulkhead fittings. If the forward engine mount bulkhead fittings
become sufficiently hydrogen embrittled, they may not be able to carry design loads. It is believed that
hydraulic fluid contamination is entering the dry bay through the condensate drain line. The condensate
drain connects to the system disconnect box drain lines, which drains hydraulic fluid and fuel from the
system disconnect box. The system disconnect box drain hose can clog due to hydraulic fluid coking
in the drain lines. This allows hydraulic fluid to back up into strut forward dry bay through the condensate
drain line. Boeing Service Bulletin 777-54-0027 addresses blockage of the strut forward drain lines. If
a fitting becomes embrittled, fitting and/or strut replacement may be required. If the fitting becomes
sufficiently brittle, it may not be able to carry design loads.
Inspection of the strut forward dry bay for the presence of hydraulic fluid contamination will help prevent
hydrogen embrittlement of the titanium forward engine mount bulkhead fittings.
Boeing Fleet Team Digest (FTD) 777 FTD 54-11001 is related to this service bulletin.
Boeing Service Related Problem (SRP) 777-SRP-54-0138 is related to this service bulletin.
Revision 1 is sent to:
1. Add airplanes WC587, WC593, WC594, and WC595 to the effectivity of this service bulletin as
Group 2 Airplanes. Subsequent to the release of this service bulletin it was determined that a
production change that was to be installed on these airplanes that would have terminated the
inspections in this service bulletin could not be installed. Therefore the inspection of these airplanes
in accordance with this service bulletin is required. Group 2 Airplanes are the same as Group 1
Airplanes, except for the compliance time for the initial inspection.
2. Revise compliance table and work instructions to show that finish restoration is not required until
the repairs are required.
3. Clarify that hydraulic fluid contamination includes hydraulic fluid contamination in its liquid (fluid),
vapor, and/or solid (coked) form.
4. Add optional leveling compound.
5. Add an alternate method of leveling compound repair for small areas that uses sealant and does
not require airplane leveling.
D. Description
Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
15 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 16

Open the thrust reverser. Remove the strut forward dry bay access door. Do a General Visual Inspection
(GVI) for hydraulic fluid contamination in its liquid (fluid), vapor, and/or solid (coked) form. Blistered
and/or peeling primer is a sign of hydraulic fluid contamination and the strut forward dry bay is
contaminated. Install the strut forward dry bay access door. Close the thrust reverser.
Part 2 - Strut Forward Dry Bay Interior DET Inspection
Open the thrust reverser. Remove the strut forward dry bay access door. Do a Detailed Inspection
(DET) of the interior of the strut forward dry bay for hydraulic fluid coking, heat discoloration, damage
to sealant and primer, damage to leveling compound, cracks; and etching or pitting. Clean and restore
sealant, primer, and leveling compound of the detail parts in the strut forward dry bay if missing, blistered,
peeling, or damaged. Check drain lines and clean or replace drain lines as required. Install the strut
forward dry bay access door. Close the thrust reverser.
Part 3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection
Open the thrust reverser. Remove the strut forward dry bay access door. Do a DET and High Frequency
Eddy Current (HFEC) inspection of the strut forward engine mount bulkhead upper and lower fittings
for cracks, and etching or pitting. Clean and restore sealant, primer, and leveling compound of the
detail parts in the strut forward dry bay if missing, blistered, peeling, or damaged. Check drain lines
and clean or replace drain lines as required. Install the strut forward dry bay access door. Close the
thrust reverser.
Revision 1 - Airplanes WC587, WC593, WC594, and WC595 were added to the service bulletin effectivity
as Group 2 Airplanes. These airplanes should accomplish the initial inspection at the compliance time
in accordance with Paragraph 1.E., Compliance. No more work is necessary on the airplanes inspected
in accordance with the original issue of this service bulletin. These airplanes should repeat the inspection
at the repeat interval in accordance with Paragraph 1.E., Compliance.
The work in this service bulletin is done in the maintenance zone(s) given below.
Group 1:
Affected Maintenance Zones
ZoneModel
432, 442777-200, 777-300
Group 2:
Affected Maintenance Zones
ZoneModel
432, 442777-200
E. Compliance
Federal Aviation Administration (FAA) Airworthiness Directive AD 2013-11-14 is related to this service
bulletin. The effective date of AD 2013-11-14 is July 19, 2013.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
16 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 17

Accomplish the required actions, based on the applicable conditions, in Table 1, in accordance with
Paragraph 3. Accomplishment Instructions.
Accomplish the actions and evaluate the conditions in Table 1 separately for each strut forward dry
bay and each forward engine mount bulkhead.
The following acronyms are used in Table 1:
– GVI for General Visual Inspection.
– DET for Detailed Inspection.
– HFEC for High Frequency Eddy Current Inspection.
– Part 1 for Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection.
– Part 2 for Part 2 - Strut Forward Dry Bay Interior DET Inspection.
– Part 3 for Part 3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection
Table 1: GVI, DET, and HFEC Inspection of Strut Forward Dry Bay for Hydraulic Fluid Contamination
and Forward Engine Mount Bulkhead for Hydrogen Embrittlement.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 600 flight-cy-
cles or 12 Months af-
ter the effective date
of AD 2013-11-14,
whichever occurs
first.
Do a GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
Group 1 Airplanes
-Within 600 flight-cy-
cles or 12 Months af-
ter the Revision 1
date of this service
bulletin, whichever
occurs first.
Do a GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
Group 2 Airplanes
1,200 Flight-cy-
cles.
-Repeat GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
Condition 1 -
No hydraulic fluid contamination in
its liquid (fluid), vapor, and/or solid
(coked) form is found.
-Before further flight.Do a DET of the interior of the
strut forward dry bay in accor-
dance with Part 2 for: 1) Hy-
draulic fluid coking; and 2) Heat
discoloration; and 3) Damage to
sealant and primer; and 4)
Damage to leveling compound;
and 5) Cracks; and 6) Etching
or pitting.
Condition 2 -
Hydraulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form is found.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
17 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 18

Table 1: GVI, DET, and HFEC Inspection of Strut Forward Dry Bay for Hydraulic Fluid Contamination
and Forward Engine Mount Bulkhead for Hydrogen Embrittlement.
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
1,200 Flight-cy-
cles.
-Repeat GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
Condition 2A -
1) No hydraulic fluid coking is found;
and
2) No heat discoloration is found;
and
3) No damage to sealant and primer
is found; and
4) No damage to leveling compound
is found; and
5) No crack is found; and
6) No etching or pitting is found.
-Before further flight.Do a DET and HFEC of the inte-
rior of the strut forward engine
mount bulkhead upper and low-
er fittings for cracks and etching
or pitting in accordance with
Part 3.
Condition 2B -
1) No crack is found; and
2) No etching or pitting is found; and
3) Any of the following is found:
....a) Any Hydraulic fluid coking is
found; or
....b) Any heat discoloration is found;
or and
-Within 25 flight-cy-
cles or 10 days,
whichever occurs
first, after Condition
2B is found.
Contact The Boeing Company
for repair instructions,do the re-
pair, and restore sealant,
primer, and leveling compound.
....c) Any damage to sealant and
primer is found; or
....d) Any damage to leveling com-
pound is found.
and
1,200 Flight-cy-
cles.
-Repeat GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
-Before further flight.Contact The Boeing Company
for repair instructions,do the re-
pair, and restore sealant,
primer, and leveling compound.
Condition 2C -
1) Any crack is found; or
2) Any etching or pitting is found.
and
1,200 Flight-cy-
cles.
-Repeat GVI of the interior of the
strut forward dry bay for hy-
draulic fluid contamination in its
liquid (fluid), vapor, and/or solid
(coked) form in accordance with
Part 1.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
18 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 19

F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
In addition, the Manager of the FAA Seattle Aircraft Certification Office approves the action (i.e. inspection
or modification) defined in this service bulletin as an alternative method of compliance to the requirements
of paragraph (g) of AD 2013-11-14. All provisions of AD 2013-11-14 that are not specifically referenced
in the above statement remain fully applicable and must be complied with.
G. Manpower
The table below shows an estimate of the task hours necessary to do this inspection for each airplane.
This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator
task hour data if necessary. The estimate does not include lost time. These are some examples of lost
time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.002.002Open Access
Inspect
0.500.501...FIGURE 1
0.500.501...FIGURE 4
1.002.002Close Access
3.005.00TOTAL FOR EACH AIRPLANE
Part 2 - Strut Forward Dry Bay Interior DET Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.002.002Open Access
Inspect
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
19 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 20

Part 2 - Strut Forward Dry Bay Interior DET Inspection
Elapsed HoursTask HoursNumber of PersonsTask
4.004.001...FIGURE 2
4.004.001...FIGURE 5
2.505.002Check Drain Line
1.002.002Close Access
12.5017.00TOTAL FOR EACH AIRPLANE
Part 3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection
Elapsed HoursTask HoursNumber of PersonsTask
1.002.002Open Access
Inspect
4.004.001...FIGURE 3
4.004.001...FIGURE 6
2.505.002Check Drain Line
1.002.002Close Access
12.5017.00TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Boeing Service Bulletin 777-54-0027
b. Boeing Service Related Problem (SRP) 777-SRP-54-0138
c. Federal Aviation Administration (FAA) Airworthiness Directive (AD) 2013-11-14
d. Service Bulletin Index D624W001
e. Standard Overhaul Practices Manual (SOPM) 20-30-03, 20-43-03, 20-44-01
f. Standard Wiring Practices Manual (SWPM) 20-10-11, 20-10-12, 20-10-19
g. 777 Aircraft Maintenance Manual (AMM) 06-43-00, 08-21-00, 54-53-01, 54-55-01, 78-31-00
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
20 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 21

h. 777 Fleet Team Digest (FTD) 54-11001
i. 777 Non-Destructive Testing (NDT) Manual Part 6, 51-00-06
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
None.
K. Publications Affected
1. Publications:
None.
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin affects FCS but no new DTIs are necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
21 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 22

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
22 of 49
BOEING SERVICE BULLETIN 777-54-0028
BLANK PAGE

### Page 23

2.    MATERIAL INFORMATION
A. Material - Price and Availability
The operator can supply the parts and materials shown in Paragraph 2.C., Parts Necessary for Each
Airplane. As an alternative, operators can purchase the parts from Boeing Spares. This service bulletin
does not show the Boeing price and supply data.
B. Industry Support Information
Boeing warranty remedies are available for 777 airplanes in warranty as of June 15, 2011. For inspection
task hour reimbursement for airplanes in warranty as of that date, send a warranty claim to Boeing
Commercial Airplanes Group - Warranties. If the condition described in this service bulletin is found
during the inspection for airplanes in warranty as of that date and additional task hours are required,
send a warranty claim to Boeing Commercial Airplanes Group - Warranties. Please refer to this service
bulletin number and reference the airplane numbers in your purchase order.
C. Parts Necessary for Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
The following materials may be required to restore the sealant, primer, and leveling compound in
the strut forward dry bay.
NotesNameQTYPart Number / Specification
(c)Chemical Conversion Coating1Oz.-
(a)Primer1 Pt.BMS 10-79, TYPE III
(a)Primer1 Pt.BMS 10-11, TYPE I
(a)Sealant16 Oz.BMS 5-63
(d)Primer, Silicone1 Pt.BAC5432, COMPOUND 21, DOW CORNING
1201 RTV PRIME COAT (DOW CORNING PR-
1200 RTV PRIME COAT RED OR SS4004P
optional)
(d)Leveling Compound, Silicone2 Qt.BAC5432, COMPOUND 21, XIAMETER RTV-
3110 BASE (DC 3110 OR RTV11 optional)
(d)Catalyst1 Pt.BAC5432, COMPOUND 21, XIAMETER RTV-
3010-S CATALYST (XIAMETER RTV-3000 F
CATALYST, S TIN NW, OR RTV9950 optional)
(b)Primer, High Temperature1 Qt.SOPM 20-44-01, Type 51
(a) Refer to the Qualified Products List at the end of the Boeing Material Specification (BMS) for
supplier data.
(b) Refer to SOPM 20-44-01 for supplier data.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
23 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 24

NotesNameQTYPart Number / Specification
(c) Refer to SOPM 20-43-03 for supplier data.
(d) See supplier data below. Leveling Compound, Catalyst, and Primer need to come from same
source to ensure compatibility.
– XIAMETER RTV-3110 BASE or DC 3110 (Leveling Compound); XIAMETER RTV-3010-S,
XIAMETER RTV-3000 F, or S TIN NW (Catalyst); and DOW CORNING 1201 RTV PRIME
COAT or DOW CORNING PR-1200 RTV PRIME COAT RED (Primer)
V71984
Dow Corning Corporation
2200 W Salzburg Rd
Midland Mi 48640 - 8531
Customer Service/www.dowcorning.com
(800) 248-248
– RTV11 (Leveling Compound), RTV9950 (catalyst), and SS4004P 01 P (Primer)
V01139
Momentive Performance Materials Inc.
187 Danbury Road
Wilton Ct 06897-4122
www.momentive.com
(704) 992-4107
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
24 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 25

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
4. Refer to the SWPM 20-10-11 and SWPM 20-10-12 for the wire installation procedures,
and SWPM 20-10-19 for the wire separation requirements, as accepted procedures.
5. The necessary conditions for selection of clamp type and size are included in SWPM
20-10-12. If any wire bundle support clamp specified in this service bulletin does not
make a correct fit on the wire bundle, refer to SWPM 20-10-12 as an accepted
procedure to select a clamp that fits correctly.
6. A Detailed Inspection (DET) is defined as: An intensive examination of a specific
item, installation, or assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good lighting at an intensity
deemed appropriate. Inspection aids such as mirrors, magnifying lenses, etc. may
be necessary. Surface cleaning and elaborate procedures may be required.
7. A General Visual Inspection (GVI) is defined as: A visual examination of an interior
or exterior area, installation or assembly to detect obvious damage, failure or
irregularity. This level of inspection is made from within touching distance unless
otherwise specified. A mirror may be necessary to enhance visual access to all
exposed surfaces in the inspection area. This level of inspection is made under
normally available lighting conditions such as daylight, hangar lighting, flashlight or
drop-light and may require removal or opening of access panels or doors. Stands,
ladders or platforms may be required to gain proximity to the area being checked.
8. An HFEC inspection is a High Frequency Eddy Current inspection.
9. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
25 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 26

10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Accomplish the actions and evaluate the conditions separately for each strut forward
dry bay and each forward engine mount bulkhead.
B. WORK INSTRUCTIONS
1. Do a GVI of the interior of the strut forward dry bay for hydraulic fluid contamination in its liquid
(fluid), vapor, and/or solid (coked) form in accordance with Part 1 - Strut Forward Dry Bay Hydraulic
Fluid Contamination GVI Inspection at the compliance time specified in Paragraph 1.E., Compliance.
a. Condition 1 - No hydraulic fluid contamination in its liquid (fluid), vapor, and/or solid (coked)
form is found.
(1) Repeat GVI of the interior of the strut forward dry bay for hydraulic fluid contamination in
its liquid (fluid), vapor, and/or solid (coked) form in accordance with Part 1 - Strut Forward
Dry Bay Hydraulic Fluid Contamination GVI Inspection at the interval specified in Paragraph
1.E., Compliance.
b. Condition 2 - Hydraulic fluid contamination in its liquid (fluid), vapor, and/or solid (coked) form
is found.
(1) Do a DET of the interior of the strut forward dry bay in accordance with Part 2 - Strut
Forward Dry Bay Interior DET Inspection for: 1) Hydraulic fluid coking; and 2) Heat
discoloration; and 3) Damage to sealant and primer; and 4) Damage to leveling compound;
and 5) Cracks; and 6) Etching or pitting at the compliance time specified in Paragraph
1.E., Compliance.
(a) Condition 2A -1) No hydraulic fluid coking is found; and 2) No heat discoloration is
found; and 3) No damage to sealant and primer is found; and 4) No damage to
leveling compound is found; and 5) No crack is found; and 6) No etching or pitting
is found.
1) Repeat GVI of the interior of the strut forward dry bay for hydraulic fluid
contamination in its liquid (fluid), vapor, and/or solid (coked) form in accordance
with Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
at the interval specified in Paragraph 1.E., Compliance.
(b) Condition 2B - 1) No crack is found; and 2) No etching or pitting is found; and 3) Any
of the following is found: a) Any Hydraulic fluid coking is found; or b) Any heat
discoloration is found; or c) Any damage to sealant and primer is found; or d) Any
damage to leveling compound is found.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
26 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 27

1) Do a DET and HFEC of the interior of the strut forward engine mount bulkhead
upper and lower fittings for cracks, and etching or pitting in accordance with Part
3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection, at
the compliance time specified in Paragraph 1.E., Compliance; and
2) Contact The Boeing Company for repair instructions, do the repair, and restore
the sealant, primer, and leveling compound at the compliance time specified in
Paragraph 1.E., Compliance. Refer to APPENDIX A as an accepted procedure
to clean and restore sealant, primer, and leveling compound of the detail parts
in the strut forward dry bay if missing, blistered, peeling, or damaged.
3) Repeat GVI of the interior of the strut forward dry bay for hydraulic fluid
contamination in its liquid (fluid), vapor, and/or solid (coked) form in accordance
with Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
at the interval specified in Paragraph 1.E., Compliance.
(c) Condition 2C - 1) Any crack is found; or 2) Any etching or pitting is found.
1) Contact The Boeing Company for repair instructions, do the repair, and restore
the sealant, primer, and leveling compound at the compliance time specified in
Paragraph 1.E., Compliance. Refer to APPENDIX A as an accepted procedure
to clean and restore sealant, primer, and leveling compound of the detail parts
in the strut forward dry bay if missing, blistered, peeling, or damaged.
2) Repeat GVI of the interior of the strut forward dry bay for hydraulic fluid
contamination in its liquid (fluid), vapor, and/or solid (coked) form in accordance
with Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
at the interval specified in Paragraph 1.E., Compliance.
Part 1 - Strut Forward Dry Bay Hydraulic Fluid Contamination GVI Inspection
1. Open the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
2. Remove the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as
accepted procedures.
Strut No. 2Strut No. 1
442AR432AR
3. Do a GVI of the interior of the strut forward dry bay for hydraulic fluid contamination in its liquid
(fluid), vapor, and/or solid (coked) form in accordance with the figure below:
Strut No. 2Strut No. 1
FIGURE 4FIGURE 1
4. Install the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as accepted
procedures.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
27 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 28

Strut No. 2Strut No. 1
442AR432AR
5. Close the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
6. Put the airplane back to a serviceable condition.
Part 2 - Strut Forward Dry Bay Interior DET Inspection.
1. Open the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
2. Remove the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as
accepted procedures.
Strut No. 2Strut No. 1
442AR432AR
3. Do a DET of the interior of the strut forward dry bay in accordance with the figure below for: 1)
Hydraulic fluid coking; and 2) Heat discoloration; and 3) Damage to sealant and primer; and 4)
Damage to leveling compound; and 5) Cracks; and 6) Etching or pitting.
NOTE: It is recommended that operators document contamination with pictures and record the
percent of contamination, and whether the lower and/or upper forward engine mount
bulkhead fittings are affected to aid in the development of The Boeing Company repair
instructions.
Strut No. 2Strut No. 1
FIGURE 5FIGURE 2
4. Deleted
5. Check drain lines for blockage; Clean or replace drain lines as required. Refer to 777 AMM 54-55-01
as an accepted procedure.
6. Install the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as accepted
procedures.
Strut No. 2Strut No. 1
442AR432AR
7. Close the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
8. Put the airplane back to a serviceable condition.
Part 3 - Strut Forward Engine Mount Bulkhead Fitting DET and HFEC Inspection
1. Open the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
28 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 29

2. Remove the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as
accepted procedures.
Strut No. 2Strut No. 1
442AR432AR
3. Do a DET and HFEC of the strut forward engine mount bulkhead upper and lower fittings for cracks,
and etching or pitting in accordance with the figure below:
NOTE: It is recommended that operators document contamination with pictures and record the
percent of contamination, and whether the lower and/or upper forward engine mount
bulkhead fittings are affected to aid in the development of The Boeing Company repair
instructions.
Strut No. 2Strut No. 1
FIGURE 6FIGURE 3
4. Deleted
5. Check drain lines for blockage; Clean or replace drain lines as required. Refer to 777 AMM 54-55-01
as an accepted procedure.
6. Install the following access panels. Refer to 777 AMM 06-43-00 and 777 AMM 54-53-01 as accepted
procedures.
Strut No. 2Strut No. 1
442AR432AR
7. Close the thrust reverser. Refer to 777 AMM 78-31-00 as an accepted procedure.
8. Put the airplane back to a serviceable condition.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1: December 10, 2013
29 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 30 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
432AR (STRUT NO.1)
LEFT STRUT
FORWARD ENGINE
\ MOUNT BULKHEAD
SIDE SKIN  LOWER FITTING
FIRE  FORWARD ENGINE
EXTINGUISHER  / MOUNT BULKHEAD
CHORD/WEB  LINE  UPPER FITTING
UPPER SPAR
CHORD/WEB
LOWER 1
SPAR
NO. 2 BULKHEAD 1)
/ CONDENSATÉ  DRAIN  LEVELING  COMPOUND  (TYPICAL)  1) SIDE SKIN
STRUT FORWARD DRY BAY
2126963
FIGURE 1: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - GVI INSPECTION
(SHEET 1 OF 2)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  777-54-0028
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  30 of 49

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a General Visual Inspection (GVI) of the inte-
rior of the strut forward dry bay for the presence
of hydraulic fluid contamination in its liquid (fluid),
vapor, and/or solid (coked) form including the
side skins and upper chords and web. The interi-
or is painted with primer. Blistered and/or peeling
primer is a sign that hydraulic fluid contamination
is present and the strut forward dry bay is con-
taminated.
--Strut Fwd Dry BayInspect1
FIGURE 1: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - GVI INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
31 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 32 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
432AR (STRUT NO.1)
LEFT STRUT
FORWARD ENGINE
SIDE SKIN 5  1) MOUNT BULKHEAD  LOWER FITTING
SEALANT T  EXTINGUISHER  LINE  FIRE  / MOUNT BULKHEAD  FORWARD ENGINE  UPPER FITTING
(TYPICAL)
CHORD/WEB
UPPER SPAR
CHORD/WEB
LOWER 3
SPAR
NO. 2 BULKHEAD 4)
/ CONDENSATÉ  DRAIN  2) COMPOUND  LEVELING  5) SIDE SKIN
(TYPICAL)
STRUT FORWARD DRY BAY
FIGURE 2: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 1 OF 4)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  777-54-0028
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  32 of 49

### Page 33

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect1
1. Hydraulic fluid coking; and
2. Missing, blistered, peeling or damaged
primer; and
3. Heat discoloration; and
4. Cracks; and
5. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
1. Hydraulic fluid coking; and
2. Missing, blistered, peeling or damaged
primer; and
3. Heat discoloration; and
4. Cracks; and
5. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET for damage. Damage is defined as
peeling or disbonding, cracking, and hardening
of the compound. Note: It is normal for the com-
pound to be discolored and stained.
--Leveling Com-
pound
Inspect2
FIGURE 2: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
33 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 34

More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
--Chord / Web - Low-
er Spar
Inspect3
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
--No. 2 BulkheadInspect4
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas on both sides of
the interior of the strut forward dry bay for:
--Side SkinInspect5
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
FIGURE 2: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
34 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 35

More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas of the top of the
interior of the strut forward dry bay for:
--Chord / Web - Up-
per Spar
Inspect6
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET for damage in the interior of the strut
forward dry bay. Sealant damage is defined as
breaks in the sealant, cuts, creases and open-
ings, peeling, or it is missing.
--SealantInspect7
FIGURE 2: STRUT NO. 1 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
35 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 36 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
432AR (STRUT NO.1)
LEFT STRUT  TEND
FWD ENGINE
MOUNT BULKHEAD 1  LEVELING
UPPER FITTING  COMPOUND
(TYPICAL)
CONDENSATE
DRAIN
NO.2 BULKHEAD
CHORD/ WEB
LOWER SPAR
12 MOUNT  FWD ENGINE
STRUT FORWARD DRY BAY  BULKHEAD  LOWER FITTING
B  2127034
FIGURE 3: STRUT NO. 1 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC INSPECTION
(SHEET 1 OF 2)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-54-0028
Work - See page 1 for details.  36 0f 49

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect1
1. Cracks; and
2. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, damaged leveling compound,
and any fluids. Refer to SOPM 20-30-03 as an
accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
1. Cracks; and
2. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a HFEC inspection of the accessible areas
in the interior of the strut forward dry bay for
cracks in the areas where hydraulic fluid coking,
heat discoloration, damage to sealant, missing,
blistered, peeling or damaged primer, and dam-
age to leveling compound was found, in accor-
dance with 777 NDT Part 6, 51-00-06.
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect2
Do a HFEC inspection of the accessible areas
in the interior of the strut forward dry bay for
cracks in the areas where hydraulic fluid coking,
heat discoloration, damage to sealant, missing,
blistered, peeling or damaged primer, and dam-
age to leveling compound was found, in accor-
dance with 777 NDT Part 6, 51-00-06.
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
FIGURE 3: STRUT NO. 1 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
37 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 38 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
442AR (STRUT NO.2)
RIGHT STRUT
FORWARD ENGINE
SIDE SKIN  1) MOUNT BULKHEAD
LOWER FITTING
EXTINGUISHER  FIRE  / MOUNT BULKHEAD  FORWARD ENGINE
LINE  UPPER FITTING
CHORD/WEB
UPPER SPAR
CHORD/WEB
LOWER 1
SPAR
NO. 2 BULKHEAD 1
/ CONDENSATÉ  DRAIN  LEVELING  (TYPICAL)  COMPOUND  1) SIDE SKIN
STRUT FORWARD DRY BAY
2127039
FIGURE 4: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - GVI INSPECTION
(SHEET 1 OF 2)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  8200-+-LLL
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  38 of 49

### Page 39

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a General Visual Inspection (GVI) of the inte-
rior of the strut forward dry bay for the presence
of hydraulic fluid contamination in its liquid (fluid),
vapor, and/or solid (coked) form including the
side skins and upper chords and web. The interi-
or is painted with primer. Blistered and/or peeling
primer is a sign that hydraulic fluid contamination
is present and the strut forward dry bay is con-
taminated.
--Strut Fwd Dry BayInspect1
FIGURE 4: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - GVI INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
39 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 40 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
442AR (STRUT NO.2)
RIGHT STRUT
FORWARD ENGINE
SIDE SKIN 5  1)  ) MOUNT BULKHEAD  LOWER FITTING
SEALANT T  EXTINGUISHER  LINE  FIRE  • MOUNT BULKHEAD  FORWARD ENGINE  UPPER FITTING
(TYPICAL)
CHORD/WEB
UPPER SPAR
CHORD/WEB
LOWER 3
SPAR
NO. 2 BULKHEAD 4)
/CONDENSATÉ  DRAIN  2 LEVELING  COMPOUND  5) SIDE SKIN
(TYPICAL)
STRUT FORWARD DRY BAY
2127040
FIGURE 5: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 1 OF 4)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-54-0028
Work - See page 1 for details.  40 of 49

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect1
1. Hydraulic fluid coking; and
2. Missing, blistered, peeling or damaged
primer; and
3. Heat discoloration; and
4. Cracks; and
5. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
1. Hydraulic fluid coking; and
2. Missing, blistered, peeling or damaged
primer; and
3. Heat discoloration; and
4. Cracks; and
5. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET for damage. Damage is defined as
peeling or disbonding, cracking, and hardening
of the compound. Note: It is normal for the com-
pound to be discolored and stained.
--Leveling Com-
pound
Inspect2
FIGURE 5: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
41 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 42

More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
--Chord / Web - Low-
er Spar
Inspect3
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
--No. 2 BulkheadInspect4
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET of the visible areas on both sides of
the interior of the strut forward dry bay for:
--Side SkinInspect5
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
FIGURE 5: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
42 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 43

More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas of the top of the
interior of the strut forward dry bay for:
--Chord / Web - Up-
per Spar
Inspect6
1. Missing, blistered, peeling or damaged
primer; and
2. Cracks; and
3. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a DET for damage in the interior of the strut
forward dry bay. Sealant damage is defined as
breaks in the sealant, cuts, creases and open-
ings, peeling, or it is missing.
--SealantInspect7
FIGURE 5: STRUT NO. 2 - FORWARD DRY BAY INTERIOR - DET INSPECTION
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
43 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 44 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
442AR (STRUT NO.2)
RIGHT STRUT  TEND
FWD ENGINE
MOUNT BULKHEAD 1  2  LEVELING
UPPER FITTING  COMPOUND
(TYPICAL)
CONDENSATE
DRAIN
NO.2 BULKHEAD
CHORD/ WEB
LOWER SPAR
12 MOUNT  FWD ENGINE
STRUT FORWARD DRY BAY  BULKHEAD  LOWER FITTING
B  2127037
FIGURE 6: STRUT NO. 2 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC INSPECTION
(SHEET 1 OF 2)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-54-0028
Work - See page 1 for details.  44 of 49

### Page 45

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
More DataQtyIdentificationNameTaskStep
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect1
1. Cracks; and
2. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, damaged leveling compound,
and any fluids. Refer to SOPM 20-30-03 as an
accepted procedure.
Do a DET of the visible areas in the interior of
the strut forward dry bay for:
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
1. Cracks; and
2. Etching or pitting.
Clean area, as required, to remove loose dirt,
peeling primer, and any fluids. Refer to SOPM
20-30-03 as an accepted procedure.
Do a HFEC inspection of the accessible areas
in the interior of the strut forward dry bay for
cracks in the areas where hydraulic fluid coking,
heat discoloration, damage to sealant, missing,
blistered, peeling or damaged primer, and dam-
age to leveling compound was found, in accor-
dance with 777 NDT Part 6, 51-00-06.
1-Fwd Engine Mount
Bulkhead Upper
Fitting
Inspect2
Do a HFEC inspection of the accessible areas
in the interior of the strut forward dry bay for
cracks in the areas where hydraulic fluid coking,
heat discoloration, damage to sealant, missing,
blistered, peeling or damaged primer, and dam-
age to leveling compound was found, in accor-
dance with 777 NDT Part 6, 51-00-06.
1-Fwd Engine Mount
Bulkhead Lower
Fitting
Inspect
FIGURE 6: STRUT NO. 2 - FORWARD ENGINE MOUNT BULKHEAD FITTING - DET AND HFEC INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
45 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 46 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
FOR LEFT STRUT
FOR RIGHT STRUT
432AR (STRUT NO.1)
442AR (STRUT NO.2)
LEFT STRUT SHOWN,
RIGHT STRUT OPPOSITE
FWD ENGINE
3) MOUNT BULKHEAD
LOWER SPAR  CHORD/WEB 3  SIDE SKIN 2  LOWER FITTING
FWD ENGINE
CHORD/WEB  MOUNT
UPPER SPAR  BULKHEAD
UPPER FITTING
NO.2 BULKHEAD 2
(TYPICAL)  SEALANT 6
25) SIDE SKIN
COMPOUND + 8 g  (TYPICAL)  LEVELING  STRUT FORWARD DRY BAY  2127066
APPENDIX A: CLEANING AND REFINISHING OF STRUT FWD DRY BAY DETAILS
(SHEET 1 OF 4)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-54-0028
Work - See page 1 for details.  46 of 49

### Page 47 (OCR)

BOEING SERVICE BULLETIN 777-54-0028
FWD ENGINE
MOUNT BULKHEAD
LOWER SPAR  OWER SPAR 3  SIDE SKIN 2G  LOWER FITTING
FWD ENGINE
CHORD/WEB  3)  ) MOUNT BULKHEAD
UPPER SPAR  UPPER FITTING
NO.2 BULKHEAD 13
(TYPICAL)  TYPICAL €
5) SIDE SKIN
LEVELING
COMPOUND 78 g
(TYPICAL)  STRUT FORWARD DRY BAY
C  2127176
APPENDIX A: CLEANING AND REFINISHING OF STRUT FWD DRY BAY DETAILS
(SHEET 2 OF 4)
Original Issue: May 25, 2012
Revision 1 December 10, 2013  Export Controlled ECCN: 9E991 - BOEING  777-54-0028
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  47 of 49

### Page 48

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
NOTE: When cleaning, do not use solvents which contain chlorinated hydrocarbons. This can result
in hydrogen embrittlement of the titanium parts when the parts enter service and are exposed
to heat. Refer to SOPM 20-30-03 as an accepted procedure.
1.
2. If leveling compound is being applied, level airplane. Refer to 777 AMM 08-21-00 as an
accepted procedure. Leveling the airplane is not required if repairing small damaged areas,
1 square inch or less, with sealant.
More DataQtyIdentificationNameTaskStep
Not Shown. Solvent clean the interior of
surfaces of the strut forward dry bay
area, as required. Refer to SOPM 20-30-
03 as an accepted procedure.
--Strut Fwd Dry BayClean1
To the aluminum No. 2 Bulkhead Assem-
bly and the Side Skins only. Refer to
SOPM 20-43-03, Type 2, class A as an
accepted procedure.
--Chemical Conver-
sion Coating
Apply2
Apply one coat. Cure at room tempera-
ture.
-SOPM 20-44-01, Type
51
Primer, High Tem-
perature
Apply3
Apply two coats. Upper spar chord and
web.
BMS 10-11, TYPE IPrimerApply4
Apply one coat. Side skin.BMS 10-79, TYPE IIIPrimerApply5
Restore fillet seals as required.-BMS 5-63SealantApply6
Remove damaged leveling compound.--Leveling Com-
pound
Remove7
Apply primer to the bare surfaces where
leveling compound will be applied. This
will ensure proper adhesion of the level-
ing compound. Not required if doing op-
tional sealant repair in step applying the
leveling compound below.
-BAC 5432, COM-
POUND 21, DOW
CORNING 1201 RTV
PRIME COAT (DOW
CORNING PR-1200
RTV PRIME COAT
RED OR SS4004P op-
tional)
Primer, SiliconeApply
APPENDIX A:  CLEANING AND REFINISHING OF STRUT FWD DRY BAY DETAILS
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
48 of 49
BOEING SERVICE BULLETIN 777-54-0028

### Page 49

More DataQtyIdentificationNameTaskStep
Mix with catalyst in accordance with the
manufacturer's instructions to form the
leveling compound. Not required if doing
optional sealant repair in step applying
the leveling compound below.
-BAC 5432, COM-
POUND 21, COM-
POUND 21, XIAME-
TER RTV-3110 BASE
(DC 3110 OR RTV11
optional)
Leveling Com-
pound, Silicone
Make8
Mix with silicone in accordance with the
manufacturer's instructions to form the
leveling compound. Not required if doing
optional sealant repair in step applying
the leveling compound below.
-BAC 5432, COM-
POUND 21, XIAME-
TER RTV-3010-S CAT-
ALYST (XIAMETER
RTV-3000 F CATA-
LYST, S TIN NW, OR
RTV9950 optional)
CatalystMake
Pour the leveling compound into the
forward corners, until it is level with the
bottom of the fitting or drain hole. Do not
block drain hole. Not required if doing
optional sealant repair below.
--Leveling Com-
pound
Apply9
Optional for areas that are 1 square inch or less.
Leveling airplane is not required if using this method.
Smooth into existing leveling compound.-BMS 5-63SealantApply
APPENDIX A:  CLEANING AND REFINISHING OF STRUT FWD DRY BAY DETAILS
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: May 25, 2012
777-54-0028Revision 1 December 10, 2013
49 of 49
BOEING SERVICE BULLETIN 777-54-0028

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
