# Boeing Special Attention Service Bulletin 777-57-0063: Revision 1

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2010-0376; AD 2010-23-15 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 777-57-0063](https://openairdocs.org/service-documents/boeing/sb-777-57-0063.md)
- Title as filed: Boeing Commerical Airplanes - Service Bulletin
- Pages: 58
- PDF: https://openairdocs.org/files/sha256/b3/ee/b3ee0dec5ed5f1ef1d4b23254f85add12f3662cc660eb2855b6309f74449fcac
- Page: https://openairdocs.org/service-documents/boeing/sb-777-57-0063/file/b3ee0dec5ed5

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-57-0063
Original Issue: November 20, 2008
Revision 1: May 14, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Wing Center Section - Sealant Repair
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 730-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL, AND/OR TRADE SECRET
Copyright © 2008 The Boeing Company
Unpublished Work - All Rights Reserved
Boeing claims copyright in each page of this document only to the extent that the page contains copyrightable
subject matter. Boeing also claims copyright in this document as a compilation and/or collective work.
This document includes proprietary information owned by The Boeing Company and/or one or more third parties.
Treatment of the document and the information it contains is governed by contract with Boeing. For more
information, contact The Boeing Company, P .O. Box 3707, Seattle, Washington 98124.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner,
BBJ, DC-8, DC-9, DC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and the Boeing livery are all
trademarks owned by The Boeing Company; and no trademark license is granted in connection with this document
unless provided in writing by Boeing.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
1 of 58
3.0

### Page 2

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
2 of 58
BOEING SERVICE BULLETIN 777-57-0063
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ..................................................... 7
1. PLANNING INFORMATION ........................................ 1 1
A. Effectivity ............................................... 1 1
1. Airplanes ............................................ 1 1
2. Spares Affected ........................................ 1 3
B. Concurrent Requirements ...................................... 1 3
C. Reason ................................................ 1 3
D. Description .............................................. 1 4
E. Compliance .............................................. 1 4
F . Approval ............................................... 1 5
G. Manpower .............................................. 1 5
H. Weight and Balance Changes .................................... 1 6
I. Electrical Load Data ......................................... 1 6
J. References .............................................. 1 6
1. Existing Data .......................................... 1 6
2. Data supplied with this Service Bulletin ............................ 1 6
3. Installation Drawings Used in the Preparation of this Service Bulletin ............ 1 6
K. Publications Affected ......................................... 1 7
L. Interchangeability and Intermixability of Parts ........................... 1 7
2. MATERIAL INFORMATION ........................................ 1 9
A. Material - Price and Availability ................................... 1 9
B. Industry Support Information .................................... 1 9
C. Parts Necessary For Each Airplane ................................. 1 9
1. Kits/Parts ............................................ 1 9
2. Parts and Materials Supplied by the Operator ........................ 1 9
3. Parts Modified and Reidentified ................................ 1 9
4. Parts Removed and Not Replaced .............................. 1 9
D. Parts Necessary to Change Spares ................................. 1 9
E. Special Tooling - Price and Availability ............................... 1 9
F . Special Tooling Necessary to do this Service Bulletin ....................... 1 9
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 2 1
A. GENERAL INFORMATION ..................................... 2 1
B. WORK INSTRUCTIONS ....................................... 2 1
FIGURE 1: WING CENTER SECTION - LEFT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
.................................................. 2 3
FIGURE 2: WING CENTER SECTION - LEFT SIDE - LOWER AFT CORNER - SEALANT REPAIR . 26
FIGURE 3: WING CENTER SECTION - LEFT SIDE - T -CHORD SEGMENT GAP - STRINGER L-18 -
SEALANT REPAIR ....................................... 2 9
FIGURE 4: WING CENTER SECTION - LEFT SIDE - T -CHORD SEGMENT GAP - STRINGER L-12 -
SEALANT REPAIR ....................................... 3 2
FIGURE 5: WING CENTER SECTION - LEFT SIDE - T -CHORD SEGMENT GAP - STRINGER L-8 -
SEALANT REPAIR ....................................... 3 5
FIGURE 6: WING CENTER SECTION - LEFT SIDE - T -CHORD SEGMENT GAP - STRINGER L-3 -
SEALANT REPAIR ....................................... 3 8
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
3 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 4

FIGURE 7: WING CENTER SECTION - RIGHT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
.................................................. 4 1
FIGURE 8: WING CENTER SECTION - RIGHT SIDE - LOWER AFT CORNER - SEALANT REPAIR . 44
FIGURE 9: WING CENTER SECTION - RIGHT SIDE - T -CHORD SEGMENT GAP - STRINGER L-18 -
SEALANT REPAIR ....................................... 4 7
FIGURE 10: WING CENTER SECTION - RIGHT SIDE - T -CHORD SEGMENT GAP - STRINGER L-12 -
SEALANT REPAIR ....................................... 5 0
FIGURE 11: WING CENTER SECTION - RIGHT SIDE - T -CHORD SEGMENT GAP - STRINGER L-8 -
SEALANT REPAIR ....................................... 5 3
FIGURE 12: WING CENTER SECTION - RIGHT SIDE - T -CHORD SEGMENT GAP - STRINGER L-3 -
SEALANT REPAIR ....................................... 5 6
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
4 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 5

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 777-57-0063Original Issue: November 20, 2008
Revision 1: May 14, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Wing Center Section - Sealant Repair
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
No more work is necessary on airplanes changed as shown in the original issue of this service bulletin.
Airplanes WC493, WD048, WD745, and WD796 were added to the service bulletin effectivity. Airplane WD626
was deleted from the effectivity.
REASON FOR REVISION
This revision is sent to:
1. Add airplanes WC493, WD048, WD745, and WD796 to the effectivity of the service bulletin.These airplane
were inadvertantly omitted in the original issue.
2. Delete airplane WD626 from the effectivity. This airplane had the equivalent of this service bulletin
accomplished by Boeing prior to the release of the service bulletin.
The following sections were changed in this revision:
1. No sections, other than the effectivity were changed in this service bulletin.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
REVISION HISTORY
November 20, 2008Original Issue:
May 14, 2009Revision 1:
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
5 of 58

### Page 6

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
6 of 58
BOEING SERVICE BULLETIN 777-57-0063
BLANK PAGE

### Page 7

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 777-57-0063Original Issue: November 20, 2008
Revision 1: May 14, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Wing Center Section - Sealant Repair
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATEL Y .
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of the wing center section sealant repair in this service bulletin will help prevent fuel leakage
from the wing center section. Excessive leakage of fuel while the airplane is on the ground can result in pooling
of fuel. Ignition of the fuel could result in significant damage to the airplane.
Seven operators have reported 9 cases of fuel leakage from the center tank on 9 airplanes with approximately
10 to 10,000 flight-hours, 5 to 2,000 flight-cycles, and 1 to 26 months in service. See Service History table in
paragraph 1.C., Reason. The leaks were found at the two aft lower corners of the wing center section and one
leak was found at one of the four gaps between the lower t-chord segments on each side of the wing center
section. The forward lower corners and the remaining gaps between the t-chord segments are also believed to
be susceptible to fuel leakage.The leaks are believed to be the result of improperly applied sealant in production.
The incorrect application of the sealant is believed to be the result of change in the sealant application procedures.
To prevent future leakage in these areas due to improperly applied sealant, the manufacturing plans were revised
to alert personnel to the proper procedures for applying the sealant and training packages were developed for
applicable personnel. The improperly applied sealant typically fails by having a relatively large portion of the
sealant disbond and then displace. This can results in leak rates greater than normally found, with the potential
for fuel leaks up to 10 gallons per minute. This rate of leakage would be difficult to contain, as most fuel leaks
are measured in drops per minute. In-flight, the fuel would leak into areas which have been designed to
accommodate fuel leakage. However, on the ground, if not contained, the fuel leakage could result in pooling
of the fuel. This pooling combined with an ignition source could result in a fire. If the uncontained pool was large
enough, the fire could result in significant damage to the airplane.
Removal and reapplication of the sealant at the affected areas will reduce the potential of fuel leaks in the wing
center section.
Boeing Service Related Problem (SRP) 777-SRP-57-0220 and 777 Fleet Team Digest (FTD) 777 FTD 57-08006
are related to this service bulletin.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
7 of 58

### Page 8

ACTION
Drain and purge the center fuel tank. Remove the underwing bolt cover fairings. Remove the forward keel beam
access panel. Remove the wing center section access door. Remove the wing center section spanwise beam
baffle doors. Remove and repair the sealant at the four lower corners of the wing center section and the four
lower t-chord segment gaps on each side of the wing center section. Install the wing center section spanwise
beam baffle doors. Install the wing center section access panel. Monitor the four lower corners of the wing center
section and the lower t-chord area on each side of the wing center section for fuel leaks during the leak check
of the wing center section access door. Install the forward keel beam access panel. Install the underwing bolt
cover fairings.
EFFECTIVITY
777-200 airplanes with wing center sections that are designed to contain fuel, 777-200LR, 777-300, and
777-300ER airplanes. Refer to Paragraph 1.A.1., Airplanes for the list of affected airplanes.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Boeing recommends that the repair given in this service bulletin be done within 1125 days or 6,000 flight-cycles
after the date of the original issue of this service bulletin, whichever occurs first.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are available for airplanes in warranty as of April 24, 2008. Please refer to Paragraph
2.B., Industry Support Information.
MANPOWER
Elapsed HoursTotal Task HoursAirplanes
20.4040.10Group 1
MATERIAL INFORMATION
Operator Supplied Parts/Materials.
Refer to Paragraph 2.A., Material - Price and Availability
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
8 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 9 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS  REMOVE AND REPAIR THE SEALANT AT
HOLE, 139AZ  THE FOUR T-CHORD GAPS ON EACH
SIDE OF THE WING CENTER SECTION
REMOVE AND REPAIR THE SEALANT
STA  AT THE FOUR LOWER CORNERS OF
1035  THE WING CENTER SECTION
BEAM NO. 3 WING CENTER SECTION  SPANWISE  BEAM NO. 1  SPANWISE  1563794
Original Issue: November 20, 2008
Revision 1: May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  9 of 58

### Page 10

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
10 of 58
BOEING SERVICE BULLETIN 777-57-0063
BLANK PAGE

### Page 11

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-57-0063
Original Issue: November 20, 2008
Revision 1: May 14, 2009
ATA System: 5710
SUBJECT: WINGS - Center Wing - Wing Center Section - Sealant Repair
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATEL Y .
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
This service bulletin is for the airplanes shown below.
Refer to Service Bulletin Index Document D624W001 Part 3 for Airplane Variable Number, Line
Number, and Serial Number data.
DESCRIPTIONCONFIGURATIONGROUP
777-200, -200LR, -300, -300ER airplanes, line numbers 537 through
706, except line numbers 539, 540, 542, 549, 551, 556, 560, 568,
569, 576, 578, 582, 585, 590, 594, 598, 612, 619, 622, 628, 635,
641, 644, 654, 673, 683, 701, and 703. These airplanes may have
had incorrectly applied sealant in the four lower corners of the wing
center section and at the t-chord segments gaps along each side of
the wing center section.
-1
Airplane Models:
777-200, 777-200LR, 777-300, 777-300ER
GroupVariable Number
1WB142 - WB146
1WB438 - WB439
1WB512
1WC117 - WC119
1WC221 - WC222
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
11 of 58

### Page 12

GroupVariable Number
1WC364
1WC391 - WC395
1WC449
1WC459
1WC487 - WC493
1WC506 - WC508
1WC521 - WC522
1WC531 - WC536
1WC546 - WC548
1WC556
1WC566 - WC567
1WD011 - WD015
1WD031 - WD036
1WD047 - WD049
1WD066 - WD067
1WD505 - WD507
1WD532 - WD537
1WD546 - WD552
1WD564 - WD572
1WD592 - WD594
1WD653 - WD654
1WD656 - WD657
1WD671 - WD675
1WD691 - WD699
1WD741 - WD746
1WD761 - WD770
1WD786 - WD788
1WD796 - WD802
1WD826 - WD828
1WD846 - WD847
1WD871 - WD872
1WD911 - WD912
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
12 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 13

2. Spares Affected
None.
B. Concurrent Requirements
None.
C. Reason
Accomplishment of the fuel tank sealant repair in this service bulletin will help prevent fuel leakage
from the wing center section. Excessive leakage of fuel while the airplane is on the ground can result
in pooling of fuel. Ignition of the fuel could result in significant damage to the airplane.
Seven operators have reported 9 cases of fuel leakage from the center tank on 9 airplanes with
approximately 10 to 10,000 flight-hours, 5 to 2,000 flight-cycles, and 1 to 26 months in service. See
Service History table below.The leaks were found at the two aft lower corners of the wing center section
and one leak was found at one of the four gaps between the lower t-chord segments on each side of
the wing center section. The forward lower corners and the remaining gaps between the t-chord
segments are also believed to be susceptible to fuel leakage. The leaks are believed to be the result
of improperly applied sealant in production. The incorrect application of the sealant is believed to be
the result of change in the sealant application procedures. To prevent future leakage in these areas
due to improperly applied sealant, the manufacturing plans were revised to alert personnel to the proper
procedures for applying the sealant and training packages were developed for applicable personnel.
The improperly applied sealant typically fails by having a relatively large portion of the sealant disbond
and then displace. This can results in leak rates greater than normally found, with the potential for fuel
leaks up to 10 gallons per minute. This rate of leakage would be difficult to contain, as most fuel leaks
are measured in drops per minute. In-flight, the fuel would leak into areas which have been designed
to accommodate fuel leakage. However, on the ground, if not contained, the fuel leakage could result
in pooling of the fuel. This pooling combined with an ignition source could result in a fire. If the
uncontained pool was large enough, the fire could result in significant damage to the airplane.
Service History
Time in service
(Months)Flight-CyclesFlight-HoursReport No.
1252743741
1056846272
512714493
634825364
261972105865
629322156
55107
125016008
918618819
Removal and reapplication of the sealant at the affected areas will reduce the potential of fuel leaks in
the wing center section.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
13 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 14

Revision 1 is sent to:
1. Add airplanes WC493, WD048, WD745, and WD796 to the effectivity of the service bulletin.These
airplanes were inadvertantly omitted in the original issue.
2. Delete airplane WD626 from the effectivity. This airplane had the equivalent of this service bulletin
accomplished by Boeing prior to the release of the service bulletin.
The following sections were changed in Revision 1:
1. No sections, other than the effectivity were changed in this service bulletin.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the
location of important changes.
Pages with no vertical lines have no important changes.
Boeing Service Related Problem (SRP) 777-SRP-57-0220 and 777 Fleet Team Digest (FTD) 777 FTD
57-08006 are related to this service bulletin.
D. Description
Drain and purge the center fuel tank. Remove the underwing bolt cover fairings. Remove the forward
keel beam access panel. Remove the wing center section access door. Remove the wing center section
spanwise beam baffle doors. Remove and repair the sealant at the four lower corners of the wing center
section and the four lower t-chord segment gaps on each side of the wing center section. Install the
wing center section spanwise beam baffle doors. Install the wing center section access panel. Monitor
the four lower corners of the wing center section and the lower t-chord area on each side of the wing
center section for fuel leaks during the leak check of the wing center section access door. Install the
forward keel beam access panel. Install the underwing bolt cover fairings.
Revision 1 - No more work is necessary on airplanes changed as shown in the original issue of this
service bulletin. Airplanes WC493, WD048, WD745, and WD796 were added to the service bulletin
effectivity. Airplane WD626 was deleted from the effectivity.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
133, 134, 139, 195, 196777-200, 777-200LR, 777-300,
777-300ER
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin.The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Boeing recommends that the repair given in this service bulletin be done 1125 days or 6,000 flight-cycles
after the date of the original issue of this service bulletin, whichever occurs first.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
14 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 15

F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA).The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The table below shows an estimate of the task hours necessary to do this repair for each airplane.This
estimate is for direct labor only, done by an experienced crew. Adjust the estimate with operator task
hour data if necessary. The estimate does not include lost time. These are some examples of lost time:
 Time to adjust to the workplace
 Time to schedule the work
 Time to inspect the work
 Time to cure the materials
 Time to make the parts
 Time to find the tools.
Elapsed
Hours
Task
Hours
Number of
Persons
Task
4.6518.604Open Access
Sealant Repair
...Left Side
0.750.751......Lower forward corner - FIGURE 1
1.251.251......Lower aft corner - FIGURE 2
0.750.751......Lower t-chord segment gap at stringer L-18 - FIGURE 3
0.750.751......Lower t-chord segment gap at stringer L-12 - FIGURE 4
0.750.751......Lower t-chord segment gap at stringer L-8 - FIGURE 5
0.750.751......Lower t-chord segment gap at stringer L-3 - FIGURE 6
...Right Side
0.750.751......Lower forward corner - FIGURE 7
1.251.251......Lower aft corner - FIGURE 8
0.750.751......Lower t-chord segment gap at stringer L-18 - FIGURE 9
0.750.751......Lower t-chord segment gap at stringer L-12 - FIGURE 10
0.750.751......Lower t-chord segment gap at stringer L-8 - FIGURE 11
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
15 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 16

Elapsed
Hours
Task
Hours
Number of
Persons
Task
0.750.751......Lower t-chord segment gap at stringer L-3 - FIGURE 12
5.0010.002Close Access
0.751.502Test
20.4040.10TOTAL FOR EACH AIRPLANE
H. Weight and Balance Changes
None.
I. Electrical Load Data
Not changed.
J. References
1. Existing Data
a. Boeing Service Related Problem (SRP) 777-SRP-57-0220
b. Standard Overhaul Practices Manual (SOPM) 20-60-01
c. 777 Aircraft Maintenance Manual (AMM) 06-41-00, 06-44-00, 28-11-00, 28-11-02, 28-11-04,
28-26-00
d. 777 Fleet Team Digest (FTD) 57-08006
2. Data supplied with this Service Bulletin
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin
TitleDrawing Number
Lower Panel Instl Integration - BBL 122.45110W1654
Seal Application- Sect 11, Wing-To-Body Integration110W3100
Seal Application- Outbd S.O.B. Rib 1, Wing110W3125
Splice Instl - BBL 122.45, Lower Panel112W4301
These drawings were used to prepare this service bulletin. These drawings are not necessary to
make the specified changes, and are not supplied with this service bulletin. These drawings may
not be applicable to all airplane configurations or operators.
None.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
16 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 17

K. Publications Affected
None.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
17 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 18

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
18 of 58
BOEING SERVICE BULLETIN 777-57-0063
BLANK PAGE

### Page 19

2.    MATERIAL INFORMATION
A. Material - Price and Availability
None.
B. Industry Support Information
Boeing warranty remedies are available for 777 airplanes in warranty as of April 24, 2008. For task
hour and material reimbursement for airplanes in warranty as of that date, send a warranty claim to
Boeing Commercial Airplanes Group - Warranties.
C. Parts Necessary For Each Airplane
1. Kits/Parts
None.
2. Parts and Materials Supplied by the Operator
No special parts or materials are necessary to do the change in this service bulletin. But, parts
and materials in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator supply to make sure all necessary parts and materials are available.
3. Parts Modified and Reidentified
None.
4. Parts Removed and Not Replaced
None.
D. Parts Necessary to Change Spares
None.
E. Special Tooling - Price and Availability
None.
F. Special Tooling Necessary to do this Service Bulletin
No special tools or equipment are necessary to do the change in this service bulletin. But, maintenance
and overhaul tools in the manuals given in Paragraph 1.J., References, can be necessary. Examine
operator tool supply to make sure all necessary tools are available.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
19 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 20

BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
20 of 58
BOEING SERVICE BULLETIN 777-57-0063
BLANK PAGE

### Page 21

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. The instructions identified in Paragraph 3.B., Work Instructions and the Figure(s)
give the recommended sequence of steps. The sequence of steps to do this service
bulletin can be changed.
2. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
3. Obey all of the warnings and cautions given in the specified manual sections.
4. For approved fastener and process material substitutions, refer to 777 SRM, Chapter
51. Alternate fasteners are given in 777 SRM Chapter 51 and Boeing Drawing
012W6100.
5. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "as
given in" are included in the instruction, the procedure in the Boeing document must
be used.
B. WORK INSTRUCTIONS
1. Defuel center tank. Refer to 777 AMM 28-26-00 as an accepted procedure.
2. Purge and prepare to enter center tank. Refer to 777 AMM 28-11-00 as an accepted procedure.
3. Remove wing lower access panel 531AB (Left wing) and 631AB (Right wing). Refer to 777 AMM
06-44-00 as an accepted procedure.
NOTE: After the center tank is defueled and purged, fuel will continue to seep into the rework
area from the outer wing section. The seepage is greatest in the area around stringer
L-12. Sufficient rags and/or dams should be placed and monitored to prevent the fuel
from seeping into the rework areas during the sealant repair or the repaired areas may
leak.
4. Remove the forward keel beam access panel 139AL. Refer to 777 AMM 06-41-00 as an accepted
procedure.
5. Remove the wing center section access door 139AZ. Refer to as 777 AMM 28-11-02 an accepted
procedure.
6. Remove the wing center section spanwise beam baffle doors 133AZ, 133BZ, 133CZ. Refer to 777
AMM 28-11-04 as an accepted procedure.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
21 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 22

7. Remove the underwing bolt fairing covers 195DL, 195FL, and 195KL (left wing) and 196DR, 196FR,
and 196KR (right wing). Refer to 777 AMM 06-41-00 as an accepted procedure.
8. Repair sealant in the wing center section as given in the figures below.
a. Left side.
(1) Lower forward corner as given in FIGURE 1.
(2) Lower aft corner as given in FIGURE 2.
(3) Lower t-chord segment gap at stringer L-18 as given in FIGURE 3.
(4) Lower t-chord segment gap at stringer L-12 as given in FIGURE 4.
(5) Lower t-chord segment gap at stringer L-8 as given in FIGURE 5.
(6) Lower t-chord segment gap at stringer L-3 as given in FIGURE 6.
b. Right side.
(1) Lower forward corner as given in FIGURE 7.
(2) Lower aft corner as given in FIGURE 8.
(3) Lower t-chord segment gap at stringer L-18 as given in FIGURE 9.
(4) Lower t-chord segment gap at stringer L-12 as given in FIGURE 10.
(5) Lower t-chord segment gap at stringer L-8 as given in FIGURE 11.
(6) Lower t-chord segment gap at stringer L-3 as given in FIGURE 12.
9. Install wing center section spanwise beam baffle doors 133AZ, 133BZ, 133CZ. Refer to 777 AMM
28-11-04 as an accepted procedure.
10. Install wing center section access door 139AZ. Refer to as 777 AMM 28-11-02 an accepted
procedure.
11. Install wing lower access panel 531AB (Left wing) and 631AB (Right wing). Refer to 777 AMM
06-44-00 as an accepted procedure.
12. Monitor the forward and aft lower corners on the left and right side of the wing center section and
the lower t-chord area on the left and right side of the wing center section for fuel leaks during the
leak check of the wing center section access door. Refer to 777 AMM 28-11-00 as an accepted
procedure.
13. Install the underwing bolt fairing covers 195DL, 195FL, and 195KL (left wing) and 196DR, 196FR,
and 196KR (right wing). Refer to 777 AMM 06-41-00 as an accepted procedure.
14. Put the airplane back to a serviceable condition.
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1: May 14, 2009
22 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 23 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
BEAM NO. 1
FWD
WING CENTER SECTION
1564086
FIGURE 1: WING CENTER SECTION - LEFT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  23 of 58

### Page 24 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
MIN
FWD
B
1564095
FIGURE 1: WING CENTER SECTION - LEFT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  24 of 58

### Page 25

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove
and repair existing
sealant in indicated
area. Plastic or
wooden tools, recom-
mended. Refer to
777 AMM 28-11-00
as an accepted pro-
cedure.
--SealantRepair1
FIGURE 1: WING CENTER SECTION - LEFT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
25 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 26 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
BEAM NO. 1
FWD
WING CENTER SECTION
1564166
FIGURE 2: WING CENTER SECTION - LEFT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  26 of 58

### Page 27 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
2.0 MIN
FWD
1564156
FIGURE 2: WING CENTER SECTION - LEFT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  27 of 58

### Page 28

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove
and repair existing
sealant in indicated
area. Plastic or
wooden tools, recom-
mended. Refer to
777 AMM 28-11-00
as an accepted pro-
cedure.
--SealantRepair1
FIGURE 2: WING CENTER SECTION - LEFT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
28 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 29 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
FWD  BEAM NO. 1
WING CENTER SECTION
TA  1564167
FIGURE 3: WING CENTER SECTION - LEFT SIDE-T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  29 of 58

### Page 30 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
L-18
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
PADDLE FITTING  INBOARD WING  1564106
A-A
FIGURE 3: WING CENTER SECTION - LEFT SIDE -T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  30 of 58

### Page 31

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 3: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
31 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 32 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
BEAM NO. 1
FWD
WING CENTER SECTION
1564179
FIGURE 4: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-12 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  32 of 58

### Page 33 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
L-12
FWD
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
INBOARD WING  PADDLE FITTING  1564127
A-A
FIGURE 4: WING CENTER SECTION - LEFT SIDE -T-CHORD SEGMENT GAP - STRINGER L-12- SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  33 of 58

### Page 34

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 4: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-12 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
34 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 35 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
EWD  BEAM NO. 1
WING CENTER SECTION
1564188
FIGURE 5: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  35 of 58

### Page 36 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
L-8
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
PADDLE FITTING  INBOARD WING  1564135
A-A
FIGURE 5: WING CENTER SECTION - LEFT SIDE-T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  36 of 58

### Page 37

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 5: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
37 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 38 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
SPANWISE  BEAM NO. 3
BEAM NO. 1
FWD
WING CENTER SECTION
1564192
FIGURE 6: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  38 of 58

### Page 39 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
INBOARD WING  PADDLE FITTING  1564144
A-A
FIGURE 6: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  39 of 58

### Page 40

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 6: WING CENTER SECTION - LEFT SIDE - T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
40 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 41 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
WING CENTER SECTION
1564425
FIGURE 7: WING CENTER SECTION - RIGHT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  41 of 58

### Page 42 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
1564239
FIGURE 7: WING CENTER SECTION - RIGHT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  42 of 58

### Page 43

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove
and repair existing
sealant in indicated
area. Plastic or
wooden tools, recom-
mended. Refer to
777 AMM 28-11-00
as an accepted pro-
cedure.
--SealantRepair1
FIGURE 7: WING CENTER SECTION - RIGHT SIDE - LOWER FORWARD CORNER - SEALANT REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
43 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 44 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
FWD
WING CENTER SECTION
1564550
FIGURE 8: WING CENTER SECTION - RIGHT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  44 of 58

### Page 45 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
2.0 MIN
FWD
1564457
FIGURE 8: WING CENTER SECTION - RIGHT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  45 of 58

### Page 46

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove
and repair existing
sealant in indicated
area. Plastic or
wooden tools, recom-
mended. Refer to
777 AMM 28-11-00
as an accepted pro-
cedure.
--SealantRepair1
FIGURE 8: WING CENTER SECTION - RIGHT SIDE - LOWER AFT CORNER - SEALANT REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
46 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 47 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
WING CENTER SECTION
1564551
FIGURE 9: WING CENTER SECTION - RIGHT SIDE -T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  47 of 58

### Page 48 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
L-18
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
INBOARD WING
PADDLE FITTING
A-A
FIGURE 9: WING CENTER SECTION - RIGHT SIDE -T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  48 of 58

### Page 49

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 9: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-18 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
49 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 50 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
FWD
WING CENTER SECTION
1564553
FIGURE 10: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-12 -
SEALANT REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  50 of 58

### Page 51 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
S
OUTBOARD WING
PADDLE FITTING
L-12
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
PADDLE FITTING  INBOARD WING  1564256
A-A
FIGURE 10: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-12 -
SEALANT REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  51 of 58

### Page 52

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 10: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-12 -
SEALANT REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
52 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 53 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
WING CENTER SECTION
1564555
FIGURE 11: WING CENTER SECTION - RIGHT SIDE-T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  53 of 58

### Page 54 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
EXISTING
FILLET
SEAL
FUEL
FLOW
HOLE
INBOARD WING
PADDLE FITTING
A-A
FIGURE 11: WING CENTER SECTION - RIGHT SIDE -T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  54 of 58

### Page 55

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 11: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-8 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
55 of 58
BOEING SERVICE BULLETIN 777-57-0063

### Page 56 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
LEFT NO. 2
ENTRY DOOR
WING CENTER
SECTION ACCESS
HOLE, 139AZ
STA
1035
STA
1245
SPANWISE
BEAM NO. 3  SPANWISE
BEAM NO. 1
FWD
WING CENTER SECTION
1564556
FIGURE 12: WING CENTER SECTION - RIGHT SIDE -T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 1 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  56 of 58

### Page 57 (OCR)

BOEING SERVICE BULLETIN 777-57-0063
OUTBOARD WING
PADDLE FITTING
EXISTING
FILLET
SEAL
POE
- LOV
HOLE
PADDLE FITTING  INBOARD WING  1564547
A-A
FIGURE 12: WING CENTER SECTION - RIGHT SIDE-T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 2 OF 3)
Original Issue: November 20, 2008
Revision 1 May 14, 2009  777-57-0063
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.  57 of 58

### Page 58

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for one side of the airplane.
MORE DATAQTYIDENTIFICATIONNAMETASKSTEP
Carefully remove the
sealant from the gap
between the t-chord
segments from the
wing center section
paddle flitting
through the fuel flow
hole to the fillet seal
on the outboard
wing paddle fitting.
Plastic or wooden
tools, recommend-
ed. It is not neces-
sary to remove the
sealant for the full
depth of the t-chord,
only the amount re-
quired to provide an
adequate seal. Re-
pair the sealant. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure. En-
sure fuel flow hole
remains clear of de-
bris.
--SealantRepair1
Carefully remove
and repair existing
fillet seal in indicated
area around paddle
fitting existing. Plas-
tic or wooden tools,
recommended. Re-
fer to 777 AMM 28-
11-00 as an accept-
ed procedure.
--SealantRepair2
FIGURE 12: WING CENTER SECTION - RIGHT SIDE - T-CHORD SEGMENT GAP - STRINGER L-3 - SEALANT
REPAIR
(SHEET 3 OF 3)
BOEING PROPRIETARY - Copyright © Unpublished Work - See page 1 for details.
Original Issue: November 20, 2008
777-57-0063Revision 1 May 14, 2009
58 of 58
BOEING SERVICE BULLETIN 777-57-0063

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
