# Boeing Special Attention Service Bulletin 777-78-0051: U.S. DOT/FAA - SB-777-78-0051-03

- Rights: © The Boeing Company. Filed by the FAA in regulations.gov docket FAA-2014-0128; AD 2015-19-16 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Boeing Special Attention Service Bulletin 777-78-0051](https://openairdocs.org/service-documents/boeing/sb-777-78-0051.md)
- Title as filed: U.S. DOT/FAA - SB-777-78-0051-03
- Pages: 63
- PDF: https://openairdocs.org/files/sha256/ff/2c/ff2cccbea0862513a8cd8d9900b4868a8f01a9fb118861ea06616eb2bebb289d
- Page: https://openairdocs.org/service-documents/boeing/sb-777-78-0051/file/ff2cccbea086

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-78-0051
Original Issue: October 23, 2003
Revision 3: August 23, 2012
ATA System: 7811
SUBJECT: EXHAUST (TRENT 800 Series Engines) - Collector/Nozzle - Turbine Exhaust Plug
Assembly - Inspection and Retrofit
Export of this technology is controlled under the United States Export Administration Regulations (EAR) (15
CFR 300-774). An export license may be required before it is used for development, production or use by foreign
persons from specific countries. The controller of this data has the individual responsibility to abide by all export
laws.
9E991ECCN:
BOEING PROPRIETARY, CONFIDENTIAL AND/OR TRADE SECRET
Copyright © 2003 Boeing.
Unpublished Work. All Rights Reserved.
Treatment of this document and its content is governed by contract with Boeing. Rights to use this document
are licensed on a per aircraft basis and such rights may not be transferable. For more information, contact The
Boeing Company.
Boeing, the Boeing signature, the Boeing symbol, 707, 717, 727, 737, 747, 757, 767, 777, 787, Dreamliner™,
BBJ, DC-8, DC-9, DC-10, KC-10, KDC-10, MD-10, MD-11, MD-80, MD-88, MD-90, P-8A, Poseidon and Boeing
liveries are all trademarks owned by The Boeing Company; and no trademark license is granted in connection
with this document unless provided in writing by Boeing. BOEING is a trademark of Boeing Management
Company.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
1 of 63
3.0

### Page 2

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
2 of 63
BOEING SERVICE BULLETIN 777-78-0051
BLANK PAGE

### Page 3

Table of Contents
Revision Transmittal Sheet ............................................ 5
Summary ...................................................... 9
1. PLANNING INFORMATION ........................................ 1 3
A. Effectivity ............................................... 1 3
1. Airplanes ............................................ 1 3
2. Spares Affected ........................................ 1 4
B. Concurrent Requirements ...................................... 1 5
C. Reason ................................................ 1 5
D. Description .............................................. 1 6
E. Compliance .............................................. 1 8
F. Approval ............................................... 2 2
G. Manpower .............................................. 2 2
H. Weight and Balance Changes .................................... 2 5
I. Electrical Load Data ......................................... 2 5
J. References .............................................. 2 5
1. Existing Data: ......................................... 2 5
2. Data Supplied with this Service Bulletin: ........................... 2 5
3. Installation Drawings Used in the Preparation of this Service Bulletin: ........... 2 5
K. Publications Affected ........................................ 2 6
L. Interchangeability and Intermixability of Parts ........................... 2 6
M. Software Accomplishment Summary ................................ 2 6
2. MATERIAL INFORMATION ........................................ 2 7
A. Material - Price and Availability ................................... 2 7
B. Industry Support Information .................................... 2 7
C. Parts Necessary for Each Airplane ................................. 2 7
1. Kits/Parts: ........................................... 2 7
2. Parts and Materials Supplied by the Operator: ........................ 2 8
3. Parts Modified and Reidentified: ............................... 2 9
4. Parts Removed and Not Replaced: .............................. 3 0
D. Parts Necessary to Change Spares ................................. 3 0
E. Special Tooling - Price and Availability ............................... 3 1
F. Special Tooling Necessary to do this Service Bulletin ....................... 3 1
3. ACCOMPLISHMENT INSTRUCTIONS .................................. 3 3
A. GENERAL INFORMATION ..................................... 3 3
B. WORK INSTRUCTIONS ....................................... 3 4
FIGURE 1: TURBINE EXHAUST PLUG ASSEMBLY - NUTPLATE REMOVAL AND HOLE INSPECTION
PREPARATION ........................................ 3 8
FIGURE 2: TURBINE EXHAUST PLUG ASSEMBLY HOLES - GENERAL VISUAL INSPECTION . . 41
FIGURE 3: IDENTIFICATION TAG - DEEP ETCH MARK ........................ 4 2
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS ......................... 4 3
FIGURE 5: TURBINE EXHAUST PLUG ASSEMBLY BOLTS - GENERAL VISUAL INSPECTION  [Group
1, Configuration 2-3] ...................................... 4 9
FIGURE 6: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL REMAINING 3/16 INCH
DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS .................. 5 1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
3 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 4

FIGURE 7: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD PLUG, 1/4 INCH DIAMETER NUTPLATE
REPLACEMENT ........................................ 5 5
FIGURE 8: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD AND AFT PLUG IDENTIFICATION TAG
REPLACEMENT ........................................ 5 7
FIGURE 9: TURBINE EXHAUST PLUG ASSEMBLY - INSTALLATION ................ 6 0
APPENDIX A: 'WEDGELOCK' FASTENER INSTALLATION PROCESS FOR THE REPLACEMENT OF ALL
33 3/16 INCH DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS .......... 6 2
APPENDIX B: 'WEDGELOCK' AND TEMPORARY FASTENER INSTALLATION PROCESS FOR THE
REPLACEMENT OF ALL REMAINING 3/16 INCH DIAMETER BOLTS WITH 1/4 INCH
DIAMETER BOLTS ...................................... 6 3
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
4 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 5

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Revision Transmittal SheetNumber: 777-78-0051Original Issue: October 23, 2003
Revision 3: August 23, 2012
ATA System: 7811
SUBJECT: EXHAUST (TRENT 800 Series Engines) - Collector/Nozzle - Turbine Exhaust Plug
Assembly - Inspection and Retrofit
This revision includes all pages of the service bulletin.
COMPLIANCE INFORMATION RELATED TO THIS REVISION
More work is necessary on the airplane(s) changed in accordance with the Original Issue, Revision 1 or Revision
2 of this service bulletin.
Airplanes identified as Group 1 Configuration 3, that have done Revision 1 or Revision 2 of this service bulletin,
must do a general visual inspection of the fasteners that attach the forward and aft plugs of the turbine exhaust
plug assembly together of each engine, to identify if 3/16 inch diameter and/or 1/4 inch diameter bolts are used
and, if necessary, install a serviceable turbine exhaust plug assembly with 1/4 inch diameter bolts at all 33
locations of the forward and aft plug interface.
Airplanes identified as Group 1 Configuration 2, that have done the Original Issue, but not Revision 1 or Revision
2 of this service bulletin, must do a general visual inspection of the fasteners that attach the forward and aft
plugs of the turbine exhaust plug assembly together of each engine, to identify if 3/16 inch diameter and/or 1/4
inch diameter bolts are used and, if necessary, install a serviceable turbine exhaust plug assembly with 1/4 inch
diameter bolts at all 33 locations of the forward and aft plug interface. Additionally, if only 1/4 inch diameter bolts
are found installed at all 33 locations, it is recommended that the identification tag on each forward and aft plug
of each turbine exhaust plug assembly of each engine is replaced with one that has the correct post service
bulletin identity.
REASON FOR REVISION
This revision is sent because of misleading instructions in the Original Issue, Revision 1 and Revision 2 of this
service bulletin. As a result, some airplanes could have turbine exhaust plug assemblies with a mix of 1/4 inch
and 3/16 inch diameter bolts used to attach the forward and aft plugs together. After accomplishment of the
change in this service bulletin only 1/4 inch diameter bolts are to be installed at all 33 locations of the forward
and aft plug interface of each turbine exhaust plug assembly, which is the same as the latest production
configuration. Also this revision corrects a post service bulletin identification relationship error for the forward
and aft plug, where the instructions of the Original Issue, Revision 1 and Revision 2 of this service bulletin gave
them the identification intended for the next higher assembly part number.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
5 of 63

### Page 6

These sections are changed:
– Summary Background paragraph and Paragraph 1.C., Reason: Changed to add more in-service data and
correct the intent of this service bulletin to agree with the reason for this revision. Also Boeing Fleet Team
Digest (FTD) reference is added.
– Summary Action paragraph and Paragraph 1.D., Description: Changed to add applicability and the work
necessary related to the reason for this revision.
– Summary Effectivity paragraph: Changed to add spares affected reference.
– Summary Compliance paragraph: Changed to refer to Paragraph 1.E., Compliance and FAA possible AD
information added.
– Summary Manpower paragraph: Changed to refer to Paragraph 1.G., Manpower.
– Summary Material Information paragraph: Changed to refer to Paragraph 2.A., Material - Price and Availability.
– Summary Illustration: Changed to add applicability and the work necessary related to the reason for this
revision.
– Paragraph 1.A.1., Airplanes: Note added related to the installation of spare turbine exhaust plugs
– Paragraph 1.A.2., Spares Affected: Changed to add turbine exhaust plug assembly part numbers and Quick
Engine Change (QEC) kits affected by this service bulletin.
– Paragraph 1.E., Compliance: Changed to give the recommended compliance for the work necessary related
to the reason for this revision. FAA possible AD information added.
– Paragraph 1.G., Manpower: Changed to add estimates for Parts 1 thru 4 and for the forward plug nutplate
replacement of the changed Paragraph 3.B., Work Instructions.
– Paragraph 1.H., Weight and Balance: Data added.
– Paragraph 1.J.1., Existing Data: FTD, AMM, Service Bulletin Index and Service Letter references added.
SRM references corrected. Boeing Drawing reference deleted.
– Paragraph 1.J.3., Installation Drawings Used in the Preparation of this Service Bulletin: Data added.
– Paragraph 1.M., Software Accomplishment Summary: Section added.
– Paragraph 2.A., Material - Price and Availability: ROLT data changed.
– Paragraph 2.C., Kits/Parts: Existing part number data added. Invalid rivet part number MS20427-3M4
corrected to MS20427M3-4.
– Paragraph 2.C.2., Parts and Material Supplied by the Operator: Changed to show parts and materials
necessary for Component Work.
– Paragraph 2.C.3., Parts Modified and Reidentified: Changed to give the corrected turbine exhaust plug
assembly (or 'primary plug assembly') reidentification and to show other related part number data.
– Paragraph 2.D., Parts Necessary to Change Spares: Added part and kit data for Component Work.
– Paragraph 2.E., Special Tooling - Price and Availability: Added data for operator supplied special tools.
– Paragraph 2.F., Special Tooling Necessary to do this Service Bulletin: Added data that was incorrectly
located in Paragraph 2.C.2., Parts and Materials Supplied by the Operator, of the Original Issue, Revision
1 and Revision 2 of this service bulletin.
– Paragraph 3.A., General Information: Notes added and changed.
– Paragraph 3.B., Work Instructions: Changed to add Parts 1 thru 4.
– Figure 1 thru Figure 4: Changed related to Part 2 and 3.
– Figure 5 thru Figure 9: Added related to Part 1, 2 and 4.
– Appendix A and Appendix B: Added related to the installation of 'wedgelocks' and temporary fasteners in
the turbine exhaust plug assembly.
Vertical lines are put on the left edge of each page, except in Paragraph 1.A., Effectivity, to show the location
of important changes.
Pages with no vertical lines have no important changes.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
6 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 7

REVISION HISTORY
October 23, 2003Original Issue:
December 15, 2005Revision 1:
February 18, 2010Revision 2:
August 23, 2012Revision 3:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
7 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 8

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
8 of 63
BOEING SERVICE BULLETIN 777-78-0051
BLANK PAGE

### Page 9

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
SummaryNumber: 777-78-0051Original Issue: October 23, 2003
Revision 3: August 23, 2012
ATA System: 7811
SUBJECT: EXHAUST (TRENT 800 Series Engines) - Collector/Nozzle - Turbine Exhaust Plug
Assembly - Inspection and Retrofit
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
CONCURRENT REQUIREMENTS
None.
BACKGROUND
Accomplishment of this service bulletin will make sure the integrity of the interface is kept between the forward
plug and the aft plug of the turbine exhaust plug assembly to prevent separation occurrences. The aft plug can
come off during a separation occurrence which could result in a potential hazard to persons on the ground or
damage to the airplane.
Boeing has had three reports of in-flight separations of the aft plug from the forward plug, which are the two
parts of the turbine exhaust plug assembly. Subsequent to the first report where the separation occurred during
takeoff, an investigation showed that some of the interface bolts were found loose or missing. The turbine exhaust
plug assembly was sent back to Boeing for analysis and it was found that the remaining bolts had less than the
necessary minimum run-on torque value. It was also found that the operator of the analyzed turbine exhaust
plug assembly had disassembled it a minimum of three times during maintenance actions. Repeated assembly
and disassembly causes the locking property of the nut on the nutplates to wear out and subsequently let the
bolts become loose or removed in-service.
This service bulletin gives instructions to do a general visual inspection of the forward and aft plug interface
fasteners and holes of the turbine exhaust plug assembly of each engine and install 1/4 inch diameter bolts at
all 33 locations.
Boeing Service Related Problem (SRP) 777-SRP-78-0071 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 777 FTD 78-01002 is related to this service bulletin.
ACTION (PRR 62039)
Group 1, Configuration 1:
Part 1 - Turbine Exhaust Plug - Airplane Work
1. Install a serviceable turbine exhaust plug assembly on each engine with 1/4 inch diameter bolts at all
33 locations of the forward and aft plug interface.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
9 of 63

### Page 10

NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
Group 1, Configuration 2-3:
Part 1 - Turbine Exhaust Plug - Airplane Work
1. Do a general visual inspection of the 33 bolt locations of the forward and aft plug interface of each
turbine exhaust plug assembly of each engine.
2. If only 3/16 inch diameter bolts are found used, or if a mix of 3/16 inch and 1/4 inch diameter bolts are
found used, install a serviceable turbine exhaust plug assembly on each engine with 1/4 inch diameter
bolts at all 33 locations of the forward and aft plug interface.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 2 or 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
3. For Group 1 Configuration 2 airplanes only, if only 1/4 inch diameter bolts are found installed at all 33
locations, reidentify turbine exhaust plug assembly in accordance with Part 4.
Part 2 - Replacement Of All Remaining 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts -
Component Work: 314W5520-1; 314W5521-1
1. Remove the nutplates of 3/16 inch diameter bolts from the forward plug holes that interface with the
aft plug.
2. Do a general visual inspection of the 33 holes for damage.
3. Ream the damaged hole(s) to remove damage and/or increase the diameter of all 33 holes to 1/4 inch
or all remaining 3/16 inch diameter holes to 1/4 inch. Install new nutplates for 1/4 inch diameter bolts
at all 33 locations or at all remaining locations.
4. For each component identified with part number 314W5520-1, reidentify the turbine exhaust plug
assembly in accordance with Part 4.
5. For each component identified with part number 314W5521-1, no turbine exhaust plug assembly
reidentification is necessary.
Part 3 - Replacement Of All 33 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts - Component
Work: 314W5520-15, -19; 314W5520-1; 314W5521-1
1. Remove the nutplates of the 33 3/16 inch diameter bolts from the forward plug holes that interface with
the aft plug.
2. Do a general visual inspection of the 33 holes for damage.
3. Ream the damaged hole(s) to remove damage and increase diameter of all 33 holes to 1/4 inch. Install
new nutplates for 1/4 inch diameter bolts at all 33 locations.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
10 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 11

4. For each component identified with part number 314W5520-15, 19, part mark and install identification
tags on the forward and aft plugs to reidentify the turbine exhaust plug assembly.
5. For each component identified with part number 314W5520-1, reidentify the turbine exhaust plug
assembly in accordance with Part 4.
6. For each component identified with part number 314W5521-1, no turbine exhaust plug assembly
reidentification is necessary.
Part 4 - Reidentification of the Turbine Exhaust Plug Assembly - Component Work: 314W5520-1
1. Remove the tags that have an incorrect part number identification.
2. Deep etch mark replacement identification tags and install one on the forward and aft plug.
EFFECTIVITY
777-200/300 airplanes powered by Rolls-Royce Trent 800 Series Engines. Refer to Paragraph 1.A.1., Airplanes,
for the list of affected airplanes.
Refer to Paragraph 1.A.2., Spares Affected for the list of affected components.
COMPLIANCE
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to this service
bulletin. The Airworthiness Directive will make the compliance tasks and times given in this service bulletin
mandatory.
Refer to Paragraph 1.E., Compliance.
INDUSTRY SUPPORT INFORMATION
Boeing warranty remedies are not available for the inspection and/or repair procedures given in this service
bulletin.
MANPOWER
Refer to Paragraph 1.G., Manpower.
MATERIAL INFORMATION
Boeing and Operator Supplied Kits/Parts.
Refer to Paragraph 2.A., Material - Price and Availability.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
11 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 12 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
GROUP 1 CONFIGURATION 1:
REMOVE ALL 33 3/16 INCH DIAMETER BOLTS. DO A  GENERAL VISUAL INSPECTION OF EACH HOLE AND  I AND INSTALL  FORWARD  PLUG  AFT PLUG
REPLACEMENT 1/4 INCH DI
NUTPLATES AT ALL 33 LOCA  IONS. RE-IDENTIFY THE PLUG
TURBINE EXHAUST
GROUP 1 CONFIGURATION 2 AND 3:  PLUG ASSEMBLY
DO A GENERAL VISUAL INSPECTION OF ALL 33 BOLT LOCATIONS.
IF 3/16 INCH DIAMETER BOLTS ARE FOUND, OR IF A MIX OF 3/16
AND 1/4 INCH DIAMETER BOLTS ARE FOUND, REMOVE ALL 33
BOLTS AND ALL 3/16 INCH NUTPLATES. DO A GENERAL VISUAL
NSPECTION OF EACH 3/16 INCH DIAMETER HOLE AND INCREASE
TS DIAMETER TO 1/4 INCH. IF NECESSARY, RE-IDENTIFY THE
ALL REPLACEMENT 1/4 INCH DIAMETER
ATIONS, OR INSTALL
REPLACEMENT 1/4 INCH DIAMETER BOLTS AND NUTPLATES AT
ALL REMAINING  _OCATIONS
1/4 INCH
3/16 INCH  DIAMETER BOLT
DIAMETER BOLT  (33 LOCATIONS)
FORWARD  FORWARD
PLUG  AFT PLUG  PLUG,  AFT PLUG
ALIGNMENT  ALIGNMENT
RIVET  RIVET
EWD
BEFORE  AFTER
B  W49804
Original Issue: October 23, 2003
Revision 3: August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
Work - See page 1 for details.  12 of 63

### Page 13

Commercial 
Airplanes
777
Service Bulletin
SPECIAL ATTENTION
Number: 777-78-0051
Original Issue: October 23, 2003
Revision 3: August 23, 2012
ATA System: 7811
SUBJECT: EXHAUST (TRENT 800 Series Engines) - Collector/Nozzle - Turbine Exhaust Plug
Assembly - Inspection and Retrofit
BOEING RECOMMENDS THAT EACH OPERATOR EXAMINE THIS SERVICE BULLETIN IMMEDIATELY.
1.    PLANNING INFORMATION
A. Effectivity
1. Airplanes
Refer to Service Bulletin Index D624W001 Part 3 for Airplane Variable Number, Line Number, and
Serial Number data.
This service bulletin is for the airplanes shown below. An equivalent change is on subsequent
production airplanes. Refer to PRR 62039 for data about this change.
NOTE: The airplanes shown below had the configuration of turbine exhaust plug assemblies
described in this service bulletin on their engines at delivery. Installation of spare turbine
exhaust plug assemblies since delivery could put this configuration on engines of airplanes
not shown in the effectivity below. Check your records to make sure the change in
accordance with this service bulletin is accomplished on applicable turbine exhaust plug
assemblies.
DESCRIPTIONCONFIGURATIONGROUP
777-200/300 airplanes powered by Trent 800 engines before line
position 470.
-1
That have not done the Original Issue, Revision 1 or Revision 2 of
this service bulletin
1
That have done the Original Issue, but not Revision 1 or Revision 2
of this service bulletin
2
That have done Revision 1 or Revision 2 of this service bulletin3
Airplane Models:
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
13 of 63

### Page 14

777-200, 777-300
GroupVariable Number
1WA001
1WA086 - WA093
1WA101 - WA104
1WA196 - WA198
1WB031 - WB046
1WB101 - WB106
1WB161 - WB175
1WB181 - WB192
1WB201 - WB214
1WB231 - WB247
1WB416 - WB437
1WB446 - WB453
1WB501 - WB509
1WB601 - WB606
1WB611 - WB618
1WB631 - WB638
1WB646 - WB649
1WC051 - WC073
1WC101 - WC104
2. Spares Affected
Examine your Quick Engine Change (QEC) kits for parts or components changed as shown in this
service bulletin. If any parts or components are found, refer to Paragraph 2.C., Parts Necessary
for Each Airplane, for the recommended use.
Serial Number or
Dash Number
Part Number
C0028, C0029, C0030,
C0031, C0032, C0041,
C0042, C0045, C5001,
C0049, C0050
654W0003-62
C0001, C0002654W0003-3
C0052654W0003-46
C0034, C0035654W0003-68
C0043654W0003-73
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
14 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 15

Serial Number or
Dash Number
Part Number
C0003, C0004654W0003-18
C0020654W0003-37
C0051654W0003-81
C0012654W0003-30
C0013, C0014, C0015,
C0016, C0017
654W0003-23
C0033654W0003-24
C0005, C0006, C0007654W0003-12
C0027654W0003-55
C0036, C0039654W0003-57
-3, -4QECRR777
Examine your spares supply for the parts or components identified below. If any parts or components
are found, refer to Paragraph 3.B., Work Instructions for the recommended action.
Part Number
314W5520-15
314W5520-19
314W5520-1 (a)
(a) Existing part number 314W5520-1 could also exist
because of the instructions in the Original Issue
of this service bulletin. But part number 314W5520-
1 is incorrect as the post service bulletin identity.
B. Concurrent Requirements
None.
C. Reason
Accomplishment of this service bulletin will make sure the integrity of the interface is kept between the
forward plug and the aft plug of the turbine exhaust plug assembly to prevent separation occurrences.
The aft plug can come off during a separation occurrence which could result in a potential hazard to
persons on the ground or damage to the airplane.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
15 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 16

Boeing has had three reports of in-flight separations of the aft plug from the forward plug, which are
the two parts of the turbine exhaust plug assembly. Subsequent to the first report where the separation
occurred during takeoff, an investigation showed that some of the interface bolts were found loose or
missing. The turbine exhaust plug assembly was sent back to Boeing for analysis and it was found that
the remaining bolts had less than the necessary minimum run-on torque value. It was also found that
the operator of the analyzed turbine exhaust plug assembly had disassembled it a minimum of three
times during maintenance actions. Repeated assembly and disassembly causes the locking property
of the nut on the nutplates to wear out and subsequently let the bolts become loose or removed
in-service.
This service bulletin gives instructions to do a general visual inspection of the forward and aft plug
interface fasteners and holes of the turbine exhaust plug assembly of each engine and install 1/4 inch
diameter bolts at all 33 locations.
Boeing Service Related Problem (SRP) 777-SRP-78-0071 is related to this service bulletin.
Boeing Fleet Team Digest (FTD) 777 FTD 78-01002 is related to this service bulletin.
Revision 1 was sent to tell operators that the assembly number shown on the identification tag was
incorrect in Figure 3. This revision changes the assembly number shown on the identity tag from
314W5520-1 to 314W5521-1. This revision also corrects the spelling of the word "Separate," on the
identification tag, and in the table of Figure 3. Airplane WB510, line 470, was deleted from this service
bulletin effectivity. It was included in error.
Revision 2 was sent to change the classification of the service bulletin from Standard to Special Attention
and to add a compliance recommendation. Revision 2 also corrected a typographical error, adds
damage tolerance data and adds maintenance zone data.
Revision 3 is sent because of misleading instructions in the Original Issue, Revision 1 and Revision 2
of this service bulletin. As a result, some airplanes could have turbine exhaust plug assemblies with a
mix of 1/4 inch and 3/16 inch diameter bolts used to attach the forward and aft plugs together. After
accomplishment of the change in this service bulletin only 1/4 inch diameter bolts are to be installed
at all 33 locations of the forward and aft plug interface of each turbine exhaust plug assembly, which
is the same as the latest production configuration. Also this revision corrects a post service bulletin
identification relationship error for the forward and aft plug, where the instructions of the Original Issue,
Revision 1 and Revision 2 of this service bulletin gave them the identification intended for the next
higher assembly part number.
D. Description
Group 1, Configuration 1:
Part 1 - Turbine Exhaust Plug - Airplane Work
1. Install a serviceable turbine exhaust plug assembly on each engine with 1/4 inch diameter bolts
at all 33 locations of the forward and aft plug interface.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
16 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 17

Group 1, Configuration 2-3:
Part 1 - Turbine Exhaust Plug - Airplane Work
1. Do a general visual inspection of the 33 bolt locations of the forward and aft plug interface of each
turbine exhaust plug assembly of each engine.
2. If only 3/16 inch diameter bolts are found used, or if a mix of 3/16 inch and 1/4 inch diameter bolts
are found used, install a serviceable turbine exhaust plug assembly on each engine with 1/4 inch
diameter bolts at all 33 locations of the forward and aft plug interface.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 2 or 3, or it can be a spare turbine
exhaust plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new
turbine exhaust plug assembly, with part number 314W5520-22.
3. For Group 1 Configuration 2 airplanes only, if only 1/4 inch diameter bolts are found installed at
all 33 locations, reidentify turbine exhaust plug assembly in accordance with Part 4.
Part 2 - Replacement Of All Remaining 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts -
Component Work: 314W5520-1; 314W5521-1
1. Remove the nutplates of 3/16 inch diameter bolts from the forward plug holes that interface with
the aft plug.
2. Do a general visual inspection of the 33 holes for damage.
3. Ream the damaged hole(s) to remove damage and/or increase the diameter of all 33 holes to 1/4
inch or all remaining 3/16 inch diameter holes to 1/4 inch. Install new nutplates for 1/4 inch diameter
bolts at all 33 locations or at all remaining locations.
4. For each component identified with part number 314W5520-1, reidentify the turbine exhaust plug
assembly in accordance with Part 4.
5. For each component identified with part number 314W5521-1, no turbine exhaust plug assembly
reidentification is necessary.
Part 3 - Replacement Of All 33 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts - Component
Work: 314W5520-15, -19; 314W5520-1; 314W5521-1
1. Remove the nutplates of the 33 3/16 inch diameter bolts from the forward plug holes that interface
with the aft plug.
2. Do a general visual inspection of the 33 holes for damage.
3. Ream the damaged hole(s) to remove damage and increase diameter of all 33 holes to 1/4 inch.
Install new nutplates for 1/4 inch diameter bolts at all 33 locations.
4. For each component identified with part number 314W5520-15, 19, part mark and install
identification tags on the forward and aft plugs to reidentify the turbine exhaust plug assembly.
5. For each component identified with part number 314W5520-1, reidentify the turbine exhaust plug
assembly in accordance with Part 4.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
17 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 18

6. For each component identified with part number 314W5521-1, no turbine exhaust plug assembly
reidentification is necessary.
Part 4 - Reidentification of the Turbine Exhaust Plug Assembly - Component Work: 314W5520-1
1. Remove the tags that have an incorrect part number identification.
2. Deep etch mark replacement identification tags and install one on the forward and aft plug.
Revision 1 - More work was necessary on airplanes changed as shown in the initial release of this
service bulletin. Identification tags with the incorrect assembly number should be corrected when
manpower and facilities are available.
Revision 2 - No more work was necessary on airplanes changed in accordance with Revision 1 of this
service bulletin.
Revision 3 - More work is necessary on the airplane(s) changed in accordance with the Original Issue,
Revision 1 or Revision 2 of this service bulletin.
– Airplanes identified as Group 1 Configuration 3, that have done Revision 1 or Revision 2 of this
service bulletin, must do a general visual inspection of the fasteners that attach the forward and
aft plugs of the turbine exhaust plug assembly together of each engine, to identify if 3/16 inch
diameter and/or 1/4 inch diameter bolts are used and, if necessary, install a serviceable turbine
exhaust plug assembly with 1/4 inch diameter bolts at all 33 locations of the forward and aft plug
interface.
– Airplanes identified as Group 1 Configuration 2, that have done the Original Issue, but not Revision
1 or Revision 2 of this service bulletin, must do a general visual inspection of the fasteners that
attach the forward and aft plugs of the turbine exhaust plug assembly together of each engine, to
identify if 3/16 inch diameter and/or 1/4 inch diameter bolts are used and, if necessary, install a
serviceable turbine exhaust plug assembly with 1/4 inch diameter bolts at all 33 locations of the
forward and aft plug interface. Additionally, if only 1/4 inch diameter bolts are found installed at all
33 locations, it is recommended that the identification tag on each forward and aft plug of each
turbine exhaust plug assembly of each engine is replaced with one that has the correct post service
bulletin identity.
The work in this service bulletin is done in the maintenance zone(s) given below.
Affected Maintenance Zones
ZoneModel
419, 429777-200, 777-300
E. Compliance
The Federal Aviation Administration (FAA) will possibly release an Airworthiness Directive related to
this service bulletin. The Airworthiness Directive will make the compliance tasks and times given in this
service bulletin mandatory.
Accomplish the required action(s), based on the applicable condition(s), in Table(s) 1 thru 3, in
accordance with Paragraph 3. Accomplishment Instructions.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
18 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 19

Group 1, Configuration 1:
Table 1: Turbine Exhaust Plug Assembly - Replacement Of All 33 3/16 Inch Diameter Bolts With
1/4 Inch Diameter Bolts
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 60 months
after the Revision
3 date of this ser-
vice bulletin.
Install a serviceable tur-
bine exhaust plug assem-
bly on each engine with
1/4 inch diameter bolts at
all 33 locations of the for-
ward and aft plug inter-
face in accordance with
Paragraph 3.B., Work In-
structions, Part 1, Step
2.b. (a)
All airplanes
(a) A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
Group 1, Configuration 2:
Table 2: Turbine Exhaust Plug Assembly - General Visual Inspection of Bolts
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 60 months
after the Revision
3 date of this ser-
vice bulletin.
Do a general visual in-
spection of all 33 bolt loca-
tions of each turbine ex-
haust plug assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Part 1, Step 3., to
identify if 3/16 inch and/or
1/4 inch diameters are
used at the forward and
aft plug interface.
All Airplanes
-Before further
flight.
Install a serviceable tur-
bine exhaust plug assem-
bly on each engine with
1/4 inch diameter bolts at
all 33 locations of the for-
ward and aft plug inter-
face in accordance with
Paragraph 3.B., Work In-
structions, Part 1, Step
3.a.(2). (a)
Only 3/16 inch diameter
bolts are found used at all
33 locations of the forward
and aft plug interface.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
19 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 20

Group 1, Configuration 2:
Table 2: Turbine Exhaust Plug Assembly - General Visual Inspection of Bolts
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Before further
flight.
Install a serviceable tur-
bine exhaust plug assem-
bly on each engine with
1/4 inch diameter bolts at
all 33 locations of the for-
ward and aft plug inter-
face in accordance with
Paragraph 3.B., Work In-
structions, Part 1, Step
3.b.(2). (b)
A mix of 3/16 and 1/4 inch
diameter bolts are found
used at the 33 locations of
the forward and aft plug in-
terface.
-None.Reidentify the forward
and aft plug in accor-
dance with Paragraph
3.B., Work Instructions,
Part 4, Step 1 and 2.
Only 1/4 inch diameter
bolts are found installed at
all 33 locations forward and
aft plug interface.
(a) A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
(b) A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 2, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
20 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 21

Group 1, Configuration 3:
Table 3: Turbine Exhaust Plug Assembly - General Visual Inspection of Bolts
Repeat Interval
(Not to Exceed)
Compliance TimeActionCondition
-Within 60 months
after the Revision
3 date of this ser-
vice bulletin.
Do a general visual in-
spection all 33 bolt loca-
tions of each turbine ex-
haust plug assembly in
accordance with Para-
graph 3.B., Work Instruc-
tions, Part 1, Step 3., to
identify if 3/16 inch and/or
1/4 inch diameters are
used at the forward and
aft plug interface.
All Airplanes
-Before further
flight.
Install a serviceable tur-
bine exhaust plug assem-
bly on each engine with
1/4 inch diameter bolts at
all 33 locations of the for-
ward and aft plug inter-
face in accordance with
Paragraph 3.B., Work In-
structions, Part 1, Step
3.a.(2). (a)
Only 3/16 inch diameter
bolts are found used at all
33 locations of the forward
and aft plug interface.
-Before further
flight.
Install a serviceable tur-
bine exhaust plug assem-
bly on each engine with
1/4 inch diameter bolts at
all 33 locations of the for-
ward and aft plug inter-
face in accordance with
Paragraph 3.B., Work In-
structions, Part 1, Step
3.b.(2). (b)
A mix of 3/16 and 1/4 inch
diameter bolts are found
used at the 33 locations of
the forward and aft plug in-
terface.
--None.Only 1/4 inch diameter
bolts are found installed at
all 33 locations forward and
aft plug interface.
(a) A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 3, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
(b) A serviceable turbine exhaust plug assembly can be one that is removed from the airplane
and subsequently changed in accordance with Part 2, or it can be a spare turbine exhaust
plug assembly that is changed in accordance with Part 2 or 3. Or it can be a new turbine
exhaust plug assembly, with part number 314W5520-22.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
21 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 22

F. Approval
This service bulletin was examined by the Federal Aviation Administration (FAA). The changes specified
in this service bulletin comply with the applicable regulations and are FAA approved, as well as European
Aviation Safety Agency (EASA)/Joint Aviation Authorities (JAA) approved for all EASA/JAA approved
airplanes listed in the service bulletin effectivity. This service bulletin and its approval were based on
the airplane in its original Boeing delivery configuration or as modified by other approved Boeing
changes.
If an airplane has a non-Boeing modification or repair that affects a component or system also affected
by this service bulletin, the operator is responsible for obtaining appropriate regulatory agency approval
before incorporating this service bulletin.
G. Manpower
The tables below show an estimate of the task-hours necessary to do this service bulletin for each
engine. This estimate is for direct labor only, done by an experienced crew. Adjust the estimate with
operator task-hour data if necessary. The estimate does not include lost time. These are some examples
of lost time:
— Time to adjust to the workplace
— Time to schedule the work
— Time to examine the work
— Time to cure the materials
— Time to make the parts
— Time to find the tools.
Group 1, Configuration 1:
Part 1 - Airplane Work
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Deactivate Thrust
Reverser
0.631.252Remove Turbine Ex-
haust Plug Assembly
0.631.252FIGURE 9 (a)
1.001.001Activate Thrust Re-
verser
3.254.50TOTAL FOR EACH ENGINE
(a) This estimate does not include the time to replace nutplates in accordance
with FIGURE 7, if necessary.
Group 1, Configuration 2-3:
Part 1 - Airplane Work
Elapsed HoursTask HoursNumber of PersonsTask
1.001.001Deactivate Thrust
Reverser
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
22 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 23

Group 1, Configuration 2-3:
Part 1 - Airplane Work
Elapsed HoursTask HoursNumber of PersonsTask
1.801.801FIGURE 5
0.631.252Remove Turbine Ex-
haust Plug Assembly
0.631.252FIGURE 9 (a)
1.001.001Activate Thrust Re-
verser
4.055.30TOTAL FOR EACH ENGINE
(a) This estimate does not include the time to replace nutplates in accordance
with FIGURE 7, if necessary.
Part 2 - Component Work: 314W5520-1
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002FIGURE 1
1.801.801FIGURE 2
2.354.702FIGURE 6 (a)
0.250.251FIGURE 3
0.600.601FIGURE 8
9.0015.35TOTAL FOR EACH ENGINE
(a) This estimate is the maximum time necessary, which assumes there is a
minimum of 1 1/4 inch diameter bolt installed and the remaining 32 3/16 inch
diameter bolts are to be replaced with 1/4 inch diameter bolts.
Part 2 - Component Work: 314W5521-1
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002FIGURE 1
1.801.801FIGURE 2
2.354.702FIGURE 6 (a)
8.1514.50TOTAL FOR EACH ENGINE
(a) This estimate is the maximum time necessary, which assumes there is a
minimum of 1 1/4 inch diameter bolt installed and the remaining 32 3/16 inch
diameter bolts are to be replaced with 1/4 inch diameter bolts.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
23 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 24

Part 3 - Component Work: 314W5520-15, -19
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002FIGURE 1
1.801.801FIGURE 2
0.250.251FIGURE 3
3.006.002FIGURE 4
9.0516.05TOTAL FOR EACH ENGINE
Part 3 - Component Work: 314W5520-1; 314W5521-1
Elapsed HoursTask HoursNumber of PersonsTask
4.008.002FIGURE 1
1.801.801FIGURE 2
3.006.002FIGURE 4 (a)
8.8015.80TOTAL FOR EACH ENGINE
(a) The time to do this task will be less than the estimate values, as they include
identification tag installation work which is not necessary in this task for turbine
exhaust plug assemblies identified with part number 314W5520-1 and
314W5521-1.
Part 4 - Component Work: 314W5520-1
Elapsed HoursTask HoursNumber of PersonsTask
0.250.251FIGURE 3
0.600.601FIGURE 8
0.850.85TOTAL FOR EACH ENGINE
Turbine Exhaust Plug Assembly, Forward Plug Nutplate Replacement
Elapsed HoursTask HoursNumber of PersonsTask
0.200.201FIGURE 7
0.200.20TOTAL FOR EACH NUTPLATE
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
24 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 25

H. Weight and Balance Changes
Left and Right Engine Turbine Exhaust Plug Assemblies Changed to have All 1/4
Inch Diameter Bolts at their Forward and Aft Plug Interface
Change in Moment
(Pound-Inches)
Change in Weight
(Pounds)Airplane
+ 189.5+ 0.2All
I. Electrical Load Data
Not changed.
J. References
1. Existing Data:
a. Engineering Change Memo PRR 62039.
b. Boeing Service Letter 777-SL-51-013.
c. Boeing Service Related Problem (SRP) 777-SRP-78-0071.
d. Service Bulletin Index D624W001.
e. Boeing Standard Overhaul Practices Manual (SOPM) 20-10-07, 20-50-10.
f. 777 Aircraft Maintenance Manual (AMM) 78-11-02, 78-31-00.
g. 777 Fleet Team Digest (FTD) 777 FTD 78-01002.
h. 777-200 Structural Repair Manual (SRM) 51-30-01, 51-40-02, 54-42-30.
i. 777-300 Structural Repair Manual (SRM) 51-30-01, 51-40-02, 54-42-30.
2. Data Supplied with this Service Bulletin:
None.
3. Installation Drawings Used in the Preparation of this Service Bulletin:
TitleDrawing Number
RR AFT EXHAUST PLUG ATTACHMENT INTERFACE, REPAIR
AND RETROFIT
314W5521
The table above lists applicable drawings used to prepare this service bulletin. The drawings are
not necessary to make the specified changes, and are not supplied with this service bulletin. The
drawings may not be applicable to all airplane configurations or operators.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
25 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 26

K. Publications Affected
1. Publications:
Chapter-SectionPublication
78-11777 Illustrated Parts Catalog
78-11Component Maintenance Manual
2. Damage Tolerance Based Structural Inspections:
Boeing has evaluated the repairs and/or changes in this service bulletin for effects on Fatigue
Critical Structure (FCS) and for changes to Damage Tolerance Inspections (DTI) required in the
Maintenance Program. This service bulletin does not affect FCS, therefore DTIs are not necessary.
L. Interchangeability and Intermixability of Parts
Accomplishment of this service bulletin does not affect interchangeability or intermixability of parts.
M. Software Accomplishment Summary
Not affected.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
26 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 27

2.    MATERIAL INFORMATION
A. Material - Price and Availability
Boeing can supply the kits shown in Paragraph 2.C., Parts Necessary for Each Airplane and Paragraph
2.D., Parts Necessary to Change Spares . Operators are encouraged to share schedule requirements
with Boeing for incorporation of the service bulletin. The kits are subject to the terms and conditions of
the Boeing standard purchase order acknowledgment. Prices are in United States Dollars. Terms: Net
30 days.
Reference this service bulletin and submit your purchase order by one of these methods:
1. Order on-line via ATA Spec 2000 or The Boeing PART Page
2. Fax to (206) 662-7145
REFER TO THE BOEING PART PAGE ON MYBOEINGFLEET.COM OR CONTACT FIRST RESPONDER
AT FR@BOEING.COM FOR THE LATEST REORDER LEAD TIME (ROLT) AND PRICE INFORMATION
Unit Price as of
the Revision 02
date of this Ser-
vice Bulletin (US
Dollars)
ROLT as of the
Revision 03 date
of this Service
Bulletin (Calendar
Days)
NameKit Number
$7,198567Top Kit - 777 Airplanes, Trent -800 Powered005W3246-1
$3,599553Subkit, Engine005W3246-2
B. Industry Support Information
Boeing warranty remedies are not available for the inspection and/or repair procedures given in this
service bulletin.
C. Parts Necessary for Each Airplane
1. Kits/Parts:
To get the kits/parts shown below, refer to Paragraph 2.A., Material - Price and Availability.
NOTE: One top kit and the items shown in Paragraph 2.C.2., Parts and Materials Supplied by
the Operator , as applicable, are necessary for each airplane.
Part 3 - Component Work: 314W5520-15, -19
Kit 005W3246
NotesExisting Part
Number
NameQTYNew Part Number
-1-2
Top Kit, Airplane-.005W3246-1
Subkit, Engine2-005W3246-2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
27 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 28

Part 3 - Component Work: 314W5520-15, -19
Kit 005W3246
NotesExisting Part
Number
NameQTYNew Part Number
-1-2
Identification Tag.2314W5520-23
(a)Bolt.33BACB30UU4-1
BACN11G3AE1FNutplate, Self-Locking.33BACN11G4DE1F
(a)Rivet.66MS20427M3-4
(a)Rivet.6MS20615-4M3
(a) If grip length shown is not available at Boeing, fasteners supplied in kits may be one
grip length longer than indicated. Also, if any fasteners part numbers listed are not
available or have been superseded, substitute fasteners may be supplied in kits.
2. Parts and Materials Supplied by the Operator:
The following parts or materials are necessary to do the change in this service bulletin. Parts and
materials in the manuals given in Paragraph 1.J., References, can also be necessary. Examine
operator part and material supply to make sure all necessary parts and materials are available.
Part 2 - Component Work: 314W5520-1; 314W5521-1
NotesNameQTYPart Number /
Specification
Maximum quantity. Adjust
as necessary.
Nutplate, Self-Locking64BACN11G4DE1F
Maximum quantity for two
for each nutplate. Adjust as
necessary. (a)
Rivet128MS20427M3-4
Maximum quantity. Adjust
as necessary.
Bolt64BACB30UU4-1
(a) Refer to 777 Structural Repair Manual Chapter 51 for alternate fasteners.
Part 3 - Component Work: 314W5520-1
NotesNameQTYPart Number /
Specification
Subkit, Engine1005W3246-2
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
28 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 29

Part 3 - Component Work: 314W5521-1
NotesNameQTYPart Number /
Specification
Nutplate, Self-Locking66BACN11G4DE1F
(a)Rivet132MS20427M3-4
Bolt66BACB30UU4-1
(a) Refer to 777 Structural Repair Manual Chapter 51 for alternate fasteners.
Part 4 - Component Work: 314W5520-1
NotesNameQTYPart Number /
Specification
Identification Tag4314W5520-23
(a)Rivet12MS20615-4M3
(a) Refer to 777 Structural Repair Manual Chapter 51 for alternate fasteners.
3. Parts Modified and Reidentified:
The parts shown below are changed as shown in this service bulletin. The quantity (QTY) is the
number of parts changed on each airplane. Components or subassembly parts are indented. The
quantity of the indented part is the number of parts used on the next higher assembly.
NotesNew Part NumberNameQTYExisting Part
Number
Referred to as 'Tur-
bine Exhaust Plug
Assembly'. (a) (b) (c)
(e) (f)
314W5521-1Primary Plug Assy2314W5520-15 or
314W5520-19
314W5520-1
(a) (d)-Aft Plug Assy1.314W5520-3 or
314W5520-20
(a) (d)-Forward Plug Assy1.314W5520-16 or
314W5520-21
(a) Make the change in accordance with this service bulletin.
(b) This is the part number after the change is done in accordance with this service bulletin.
(c) This part is not used in production.
(d) There is no equivalent Boeing part number for the changed part.
(e) The equivalent production part number is 314W5520-22.
(f) Existing part number 314W5520-1 could also exist because of the instructions in the Original
Issue of this service bulletin. But part number 314W5520-1 is incorrect as the post service
bulletin identity.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
29 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 30

4. Parts Removed and Not Replaced:
None.
D. Parts Necessary to Change Spares
It is recommended that primary plug assemblies (or 'turbine exhaust plug' assemblies) held as spares
are inspected in accordance with FIGURE 5 and if necessary change them in accordance with Paragraph
3.B., Work Instructions, Part 2, 3 or 4, as applicable.
To get the kits shown below, for each turbine exhaust plug assembly, refer to Paragraph 2.A., Material
- Price and Availability.
Part 2 - Component Work: 314W5520-1
QTYNamePart Number
2Identification Tag314W5520-23
32 (maximum)Nutplate, Self-Lock-
ing
BACN11G4DE1F
64 (maximum)RivetMS20427M3-4
6RivetMS20615-4M3
32 (maximum)BoltBACB30UU4-1
Part 2 - Component Work: 314W5521-1
QTYNamePart Number
32 (maximum)Nutplate, Self-Lock-
ing
BACN11G4DE1F
64 (maximum)RivetMS20427M3-4
32 (maximum)BoltBACB30UU4-1
Part 3 - Component Work: 314W5520-15, -19; 314W5520-1
QTYNameKit Number
1Subkit, Engine005W3246-2
Part 3 - Component Work: 314W5521-1
QTYNamePart Number
33Nutplate, Self-Lock-
ing
BACN11G4DE1F
66RivetMS20427M3-4
33BoltBACB30UU4-1
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
30 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 31

Part 4 - Component Work: 314W5520-1
QTYNamePart Number
2Identification Tag314W5520-23
6RivetMS20615-4M3
E. Special Tooling - Price and Availability
The operator can supply the tools shown in Paragraph 2.F., Special Tooling Necessary to do this
Service Bulletin. Tool price and supply data are not given.
F. Special Tooling Necessary to do this Service Bulletin
To get the tools shown below, refer to Paragraph 2.E., Special Tooling - Price and Availability.
Maintenance and overhaul tools in the manuals shown in Paragraph 1.J., References, can also be
necessary. Examine operator tool supply to make sure all necessary tools are available.
NamePart Number
Step ReamerST1864R-2820-2550-
4-221-4-64-2-4, or
equivalent (a)
3/16 inch diameter temporary
fastener
ST30-7216A-200-
216-1.0, or equivalent
(b)
1/4 inch diameter temporary
fastener
ST30-7216A-200-
279-1.0, or equivalent
(b)
(a) Can be purchased from: Boeing, Spares Customer
Support - MC 36-65, Boeing Spares Department,
P.O.Box 3707, Seattle, WA 98124-2207, USA.
(b) A quantity of 32 are necessary.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
31 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 32

Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
32 of 63
BOEING SERVICE BULLETIN 777-78-0051
BLANK PAGE

### Page 33

3.    ACCOMPLISHMENT INSTRUCTIONS
A. GENERAL INFORMATION
CAUTION: KEEP THE WORK AREA, WIRES AND ELECTRICAL BUNDLES CLEAN OF METAL
PARTICLES OR CONTAMINATION WHEN YOU USE TOOLS. UNWANTED MATERIAL,
METAL PARTICLES OR CONTAMINATION CAUGHT IN WIRE BUNDLES CAN CAUSE
DAMAGE TO THE BUNDLES. DAMAGED WIRE BUNDLES CAN CAUSE SPARKS OR
OTHER ELECTRICAL DAMAGE.
NOTE: 1. Manual titles are referred to by acronyms. Refer to Paragraph 1.J., References, for
definition of the acronyms.
2. Obey all of the warnings and cautions given in the specified manual sections.
3. The work instructions are divided into Parts. Task Hours and Elapsed Hours for each
Part are given in Paragraph 1.G., Manpower. You can do Part 1, 2, 3 and 4
independently.
4. Unless shown differently, these dimensions and tolerances are used:
– Linear dimensions are in inches
– Tolerance on linear dimensions, other than rivet and bolt edge margins, is plus
or minus 0.03 inch
– Tolerance on rivet and bolt edge margin is plus or minus 0.05 inch
– Angular tolerance is plus or minus 2 degrees
– Hole dimensions for standard solid rivets and fasteners are in Structural Repair
Manual (SRM) Chapter 51
– Torque limits to tighten nuts and bolts are in SRM Chapter 51
5. Use the approved fastener and process material substitutions in accordance with
SRM Chapter 51.
6. If the length of any fastener specified in this service bulletin does not meet installation
standards given in SRM Chapter 51, then a fastener of the same specification, or
an approved substitute, with a length which meets the installation standards given
in SRM Chapter 51 may be used. In addition, washers may be installed for fastener
grip length in accordance with SRM Chapter 51.
7. A General Visual Inspection is defined as: A visual examination of an interior or
exterior area, installation or assembly to detect obvious damage, failure or irregularity.
This level of inspection is made from within touching distance unless otherwise
specified. A mirror may be necessary to enhance visual access to all exposed surfaces
in the inspection area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight or drop-light and may
require removal or opening of access panels or doors. Stands, ladders or platforms
may be required to gain proximity to the area being checked.
8. These work instructions refer to procedures included in other Boeing documents.
When the words "refer to" are used and the operator has an accepted alternative
procedure, the accepted alternative procedure can be used. When the words "in
accordance with" are included in the instruction, the procedure in the Boeing document
must be used.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
33 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 34

9. Boeing Service Letter 777-SL-51-013, Damage Reporting and Repair Plan/Design
Guidelines, is an acceptable procedure to request information from Boeing for
additional structural repair instructions. The Service Letter describes what information
must be provided to Boeing before a structural repair can be provided.
10. The instructions in Paragraph 3.B., Work Instructions and the figures can include
operation of tools or test equipment. Boeing Engineering Tool Drawings, the Illustrated
Tool and Equipment Manual, and the Special Tool and Ground Handling Drawing
Index contain data on versions of the tools or test equipment that you can use. It is
permitted to use replaced tools. It is not permitted to use superseded tools.
11. If it is necessary to remove more parts for access, you can remove those parts. If
you can get access without removing identified parts, it is not necessary to remove
all of the identified parts. Jacking and shoring limitations must be observed.
12. Where the work instructions include installation of a kept part, a new or serviceable
part with the same part number can be installed as an alternative to the kept part.
B. WORK INSTRUCTIONS
Part 1 - Turbine Exhaust Plug - Airplane Work
1. Deactivate the Thrust Reversers (T/R's) for ground maintenance. Refer to 777 AMM 78-31-00 as
an accepted procedure.
2. Group 1, Configuration 1:
a. Remove the turbine exhaust plug assembly from each engine. Refer to 777 AMM 78-11-02
as an accepted procedure.
b. Install a serviceable turbine exhaust plug assembly, with 1/4 inch diameter bolts at all 33
locations of the forward and aft plug interface, back on each engine in accordance with FIGURE
9.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from the
airplane and subsequently changed in accordance with Part 3, or it can be a spare
turbine exhaust plug assembly that is changed in accordance with Part 2 or 3. Or it
can be a new turbine exhaust plug assembly, with part number 314W5520-22.
(1) If one or more of the 1/4 inch diameter bolts has a run-on torque value of less than 5.0
inch-pounds, replace the nutplate on the forward plug for each of the related bolt(s) in
accordance with FIGURE 7.
3. Group 1, Configuration 2-3:
At each engine, do a general visual inspection of the all of the 33 bolt locations at the forward and
aft plug interface in accordance with FIGURE 5.
a. Only 3/16 inch diameter bolts are found used at all 33 locations:
(1) Remove the turbine exhaust plug assembly from each engine. Refer to 777 AMM 78-11-02
as an accepted procedure.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
34 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 35

(2) Install a serviceable turbine exhaust plug assembly, with 1/4 inch diameter bolts at all 33
locations of the forward and aft plug interface, back on each engine in accordance with
FIGURE 9.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from
the airplane and subsequently changed in accordance with Part 3, or it can be
a spare turbine exhaust plug assembly that is changed in accordance with Part
2 or 3. Or it can be a new turbine exhaust plug assembly, with part number
314W5520-22.
(a) If one or more of the 1/4 inch diameter bolts has a run-on torque value of less than
5.0 inch-pounds, replace the nutplate on the forward plug for each of the related
bolt(s) in accordance with FIGURE 7.
b. A mix of 3/16 inch diameter and 1/4 inch diameter bolts are found used at the 33 locations.
(1) Remove the turbine exhaust plug assembly from each engine. Refer to 777 AMM 78-11-02
as an accepted procedure.
(2) Install a serviceable turbine exhaust plug assembly, with 1/4 inch diameter bolts at all 33
locations of the forward and aft plug interface, back on each engine in accordance with
FIGURE 9.
NOTE: A serviceable turbine exhaust plug assembly can be one that is removed from
the airplane and subsequently changed in accordance with Part 2, or it can be
a spare turbine exhaust plug assembly that is changed in accordance with Part
2 or 3. Or it can be a new turbine exhaust plug assembly, with part number
314W5520-22.
(a) If one or more of the 1/4 inch diameter bolts has a run-on torque value of less than
5.0 inch-pounds, replace the nutplate on the forward plug for each of the related
bolt(s) in accordance with FIGURE 7.
c. Only 1/4 inch diameter bolts are found installed at all 33 locations.
(1) Group 1, Configuration 2:
Reidentify the turbine exhaust plug assembly:
(a) Remove the turbine exhaust plug assembly from each engine. Refer to 777 AMM
78-11-02 as an accepted procedure.
(b) Do Part 4.
(c) Install the turbine exhaust plug assembly with the reidentified forward and aft plugs
back on each engine in accordance with FIGURE 9.
1) If one or more of the 1/4 inch diameter bolts has a run-on torque value of less
than 5.0 inch-pounds, replace the nutplate on the forward plug for each of the
related bolt(s) in accordance with FIGURE 7.
(2) Group 1, Configuration 3:
No more work is necessary.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
35 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 36

4. If not done, activate the T/R's after ground maintenance. Refer to 777 AMM 78-31-00 as an
accepted procedure.
5. Put the airplane back to a serviceable condition.
Part 2 - Replacement Of All Remaining 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts -
Component Work: 314W5520-1; 314W5521-1
1. As applicable:
– Get each spare turbine exhaust plug assembly on which the description of Part 2 is necessary
to be accomplished.
– Get each removed turbine exhaust plug assembly for which the description of Part 2 is
necessary to be accomplished.
2. Put and hold the forward plug vertically and remove all of the remaining 3/16 inch diameter nutplates
from the holes that interface with the aft plug in accordance with FIGURE 1.
3. Do a general visual inspection of the holes, related to the removed 3/16 inch diameter nutplates,
at the forward and aft plug interface in accordance with FIGURE 2.
a. If a hole has damage that is more than the 0.2910 inch limit, contact Boeing for repair
instructions. Refer to Boeing Service Letter 777-SL-51-013.
4. Install 1/4 inch diameter nutplates at all remaining hole locations where 3/16 inch diameter nutplates
were removed in accordance with FIGURE 6.
5. For each component identified with part number 314W5520-1:
a. Reidentify the turbine exhaust plug assembly in accordance with Part 4
6. For each component identified with part number 314W5521-1:
a. No turbine exhaust plug assembly reidentification is necessary.
Part 3 - Replacement Of All 33 3/16 Inch Diameter Bolts With 1/4 Inch Diameter Bolts - Component
Work: 314W5520-15, -19; 314W5520-1; 314W5521-1
1. As applicable:
– Get each spare turbine exhaust plug assembly on which the description of Part 3 is necessary
to be accomplished.
– Get each removed turbine exhaust plug assembly for which the description of Part 3 is
necessary to be accomplished.
2. Put and hold the forward plug vertically and remove all of the 33 3/16 inch diameter nutplates from
the holes that interface with the aft plug in accordance with FIGURE 1.
3. Do a general visual inspection of the holes, related to the removed 3/16 inch diameter nutplates,
at the forward and aft plug interface in accordance with FIGURE 2.
a. If a hole has damage that is more than the 0.2910 inch limit, contact Boeing for repair
instructions. Refer to Boeing Service Letter 777-SL-51-013.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
36 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 37

4. For each component identified with part number 314W5520-15, -19:
a. Deep etch mark the new identification tags for the forward and aft plugs in accordance with
FIGURE 3.
b. Install 1/4 inch diameter nutplates at all 33 hole locations and reidentify the turbine exhaust
plug assembly in accordance with FIGURE 4.
5. For each component identified with part number 314W5520-1:
a. Install 1/4 inch diameter nutplates at all 33 hole locations in accordance with FIGURE 4.
b. Reidentify the turbine exhaust plug assembly in accordance with Part 4.
6. For each component identified with part number 314W5521-1:
a. Install 1/4 inch diameter nutplates at all 33 hole locations in accordance with FIGURE 4.
b. No turbine exhaust plug assembly reidentification is necessary.
Part 4 - Reidentification of the Turbine Exhaust Plug Assembly - Component Work: 314W5520-1
1. Deep etch mark the replacement identification tags for the forward and aft plugs in accordance
with FIGURE 3.
2. Remove the incorrectly identified identification tags and install the replacement identification tags
for the forward and aft plugs in accordance with FIGURE 8.
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3: August 23, 2012
37 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 38 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
FORWARD PLUG
TYPICAL AT 33 LOCATIONS (MAXIMUM)
W47560
FIGURE 1: TURBINE EXHAUST PLUG ASSEMBLY - NUTPLATE REMOVAL AND HOLE INSPECTION
PREPARATION
(SHEET 1 OF 3)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
Work - See page 1 for details.  38 of 63

### Page 39 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
(2) AFT PLUG
3 33 LOCATIONS
1 FLUGARD
FORWARD AND AFT PLUG
(AFT PLUG PUT ON FORWARD PLUG WITHOUT  BOLTS AND NUTPLATES)  W47682
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
Step  Task  Name  Identification  Qty  More Data
Remove  RIVET  (a) (c)
Remove  NUTPLATE  BACN11G3AE1F  (b)
FIGURE 1: TURBINE EXHAUST PLUG ASSEMBLY - NUTPLATE REMOVAL AND HOLE INSPECTION
PREPARATION
(SHEET 2 OF 3)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  39 of 63

### Page 40

More DataQtyIdentificationNameTaskStep
on the aft plug.1314W5520-16 OR
314W5520-21
FORWARD PLUGPut / Hold2
on the forward plug.1314W5520-3 OR
314W5520-20
AFT PLUGPut / Hold
of each plug.33-HOLEAlign3
(a) Quantity 66, if each turbine exhaust plug assembly is to have all 33 3/16 inch diameter bolts replaced
with 1/4 inch diameter bolts. Or, quantity as necessary, for each turbine exhaust plug assembly that is to
have all remaining locations that have 3/16 inch diameter bolts replaced with 1/4 inch diameter bolts.
Refer to 777-200 SRM 51-40-02 or 777-300 SRM 51-40-02 an accepted procedure.
(b) Quantity 33, if each turbine exhaust plug assembly is to have all 33 3/16 inch diameter bolts replaced
with 1/4 inch diameter bolts. Or, quantity as necessary, for each turbine exhaust plug assembly that is to
have all remaining locations that have 3/16 inch diameter bolts replaced with 1/4 inch diameter bolts.
(c) Be careful during the removal of rivets to minimize damage to the holes.
FIGURE 1: TURBINE EXHAUST PLUG ASSEMBLY - NUTPLATE REMOVAL AND HOLE INSPECTION
PREPARATION
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
40 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 41

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
More DataQtyIdentificationNameTaskStep
(a)--HOLEInspect1
(a) by general visual inspection, at the 33 locations of the forward plug and aft plug interface, for wear damage
and/or hole elongation, for each turbine exhaust plug assembly that is to have all 33 3/16 inch diameter
bolts replaced. Or, by general visual inspection, at each 3/16 inch diameter bolt location, at the forward
plug and aft plug interface, for wear damage and/or hole elongation, for each turbine exhaust plug assembly
that is to have all remaining locations that have 3/16 inch diameter bolts replaced with 1/4 inch diameter
bolts.
FIGURE 2: TURBINE EXHAUST PLUG ASSEMBLY HOLES - GENERAL VISUAL INSPECTION
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
41 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 42

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
More DataQtyIdentificationNameTaskStep
with the text as fol-
lows, for the forward
and aft plug: Assy
314W5521-1;
MATCHED SET. DO
NOT SEPARATE;
S/N: XXX-XXXX.
Refer to SOPM 20-
50-10 as an accept-
ed procedure. (a)
(b)
2314W5520-23IDENTIFICATION TAGIdentify1
(a) The serial number code is to be operator defined. A unique serial number is necessary for each matched
set of forward and aft plugs (turbine exhaust plug assembly) to help the operator keep the hardware as
a matched set. EXAMPLE: S/N TBC-0001.
(b) The serial number is recommended to be on one half of the identification tag and one-quarter inch (24
point) in height. The remaining text is recommended to be on the other half of the identification tag and
12 point in height. The text is recommended to be centered to keep a minimum 2D distance from each
of the rivets after installation.
FIGURE 3: IDENTIFICATION TAG - DEEP ETCH MARK
(SHEET 1 OF 1)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
42 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 43 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
) AFT PLUG
234€0
FORWARD
PLUG
FORWARD AND AFT PLUG
DRIVETS
FORWARD PLUG
1/4 INCH DIAMETER HOLE
(33 LOCATIONS)
EXISTING NUTPLATE RIVET
HOLES (2 LOCATIONS)
) NUTPLATE
(33 LOCATIONS)
TYPICAL  W48145
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 1 OF 6)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  Work - See page 1 for details.  777-78-0051  43 of 63

### Page 44 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
B  0.40
FORWARD PLUG  (2 LOCATIONS)
0.125
4.500
BOTTOM
DEAD CENTER
(3 LOCATIONS)
0.39
FWD  W48727
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 2 OF 6)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-78-0051
Work - See page 1 for details.  44 of 63

### Page 45 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
0.40
AFT PLUG  (2 LOCATIONS)
4.50
BOTTOM  DEAD CENTER  10 11)
(3 LOCATIONS)
0.39
FWD  W48951
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 3 OF 6)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  45 of 63

### Page 46

NOTE: If this Figure is used for a turbine exhaust plug assembly identified with part number 314W5520-1 or
314W5521-1, Steps 8 thru 11 are not necessary.
More DataQtyIdentificationNameTaskStep
in the interface holes
of the aft plug and
the forward plug. (a)
5ST30-7216A-200-216-
1.0 ('WEDGELOCK')
OR EQUIVALENT
3/16 INCH DIA FAS-
TENER
Install (Temporary)1
WARNING: USE CARE WHEN DRILLING IN TITANIUM. SMALL PARTICLES AND FINE SHAVINGS OF
TITANIUM ARE HIGHLY FLAMMABLE. WATER WITH HOT TITANIUM CAN CAUSE A STEAM
EXPLOSION. EXTINGUISH ALL FIRES OF TITANIUM WITH FULLY DRY TALC, CALCIUM
CARBONATE, SAND, OR GRAPHITE. APPLY THE POWDER TO A DEPTH OF ONE-HALF
INCH OR MORE OVER THE BURNING METAL. DO NOT USE FOAM, WATER, CARBON
TETRACHLORIDE, OR CARBON DIOXIDE. IF YOU DO NOT OBEY, YOU CAN CAUSE INJURY
TO PERSONS.
to 1/4 inch diameter,
Class III hole. Use
Step Reamer part
number ST1864R-
2820-2550-4-221-4-
64-2-4, or equiva-
lent, between the
first and fifth 'wedge-
locks' to remove
damage up to the
repair limit, or to in-
crease its diameter
to 1/4 inch. (c)
1-HOLEReam2
that was reamed, by
general visual in-
spection, to make
sure there is no
damage.
1-HOLEInspect3
into the repaired or
increased diameter
hole. (a)
1ST30-7216A-200-279-
1.0 ('WEDGELOCK')
OR EQUIVALENT
1/4 INCH DIA FASTEN-
ER
Install (Temporary)4
that were temporari-
ly installed. (a)
5ST30-7216A-200-216-
1.0 ('WEDGELOCK')
OR EQUIVALENT
3/16 INCH DIA FAS-
TENER
Remove / Keep5
that were temporari-
ly installed.
32ST30-7216A-200-279-
1.0 ('WEDGELOCK')
OR EQUIVALENT
1/4 INCH DIA FASTEN-
ER
Remove6
1314W5520-3 OR
314W5520-20
AFT PLUGRemove / Keep
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 4 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
46 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 47

More DataQtyIdentificationNameTaskStep
on the inner circum-
ference of the for-
ward plug using the
existing rivet holes.
33BACN11G4DE1FNUTPLATEInstall (New)7
(d)66MS20427M3-4RIVETInstall (New)
CAUTION: ADJUST THE IDENTIFICATION TAG POSITIONS TO AVOID DRILLING HOLES WITHIN 0.31
INCHES OF A WELD CENTERLINE
identified for the for-
ward plug. (b)
1314W5520-23IDENTIFICATION TAGPut / Hold8
0.124 - 0.128 inch
diameter. (c)
3-HOLEDrill / Ream
identified for the for-
ward plug.
1314W5520-23IDENTIFICATION TAGInstall (New)9
(d)3MS20615-4M3RIVETInstall (New)
identified for the aft
plug. (b)
1314W5520-23IDENTIFICATION TAGPut / Hold10
0.124 - 0.128 inch
diameter. (c)
3-HOLEDrill / Ream
identified for the aft
plug.
1314W5520-23IDENTIFICATION TAGInstall (New)11
(d)3MS20615-4M3RIVETInstall (New)
(a) Do not install the 'wedgelocks' (or equivalent 3/16 inch diameter temporary fasteners) in a continuous
sequence. Install the first 'wedgelock' in the hole located sequentially next to the hole that is found to have
the largest damage. Install the second 'wedgelock' in the hole nearest to the circumferential opposite of
the first 'wedgelock' installed. Install the third 'wedgelock' in the hole nearest to the circumferential midpoint
between the first and second 'wedgelocks'. Install the fourth 'wedgelock' in the hole nearest to the circum-
ferential opposite as the third installed 'wedgelock'. Install the fifth 'wedgelock' in the hole located sequen-
tially next to the hole that to has the largest damage. After the hole is reamed and no damage is found,
install a 1/4 inch 'wedgelock' in the repaired or increased diameter hole. Move the first thru fifth 'wedgelocks'
clockwise or counter-clockwise to repair the hole with the next largest damage, until 5 3/16 inch diameter
'wedgelocks' cannot be installed because 1/4 inch diameter 'wedgelocks' are installed. Do steps 1 thru 5
again to repeat this process until 32 holes are filled with 1/4 inch 'wedgelocks' and all of the 33 holes are
repaired and/or increased to 1/4 inch diameter. Refer to APPENDIX A for a graphical example of the
'wedgelock' installation process.
(b) The identification tag is to be positioned on the side of the stringer where the distance between the stringer
and the skin chem-milled area is maximum, but with the minimum conditions that there is a 2D edge
margin between the rivets and the edges of the identification tag and that there is a 2D edge margin be-
tween the rivets and the chemically milled area. Refer to 777-200 SRM 54-42-30 or 777-300 SRM 54-42-
30 for turbine exhaust plug assembly details.
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 5 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
47 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 48

More DataQtyIdentificationNameTaskStep
(c) Refer to SOPM 20-10-07 and 777-200 SRM 51-30-01 or 777-300 SRM 51-30-01 Section 5, as an accepted
procedure, to drill or ream titanium.
(d) Refer to 777-200 SRM 51-40-02 or 777-300 SRM 51-40-02 as an accepted procedure.
FIGURE 4: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL 33 3/16 INCH DIAMETER
BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 6 OF 6)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
48 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 49 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
This Figure applies only to: Group 1, Configuration 2-3.
FORWARD  AFT PLUG
PLUG
FORWARD
3/16 INCH 1  PLUG  TURBINE EXHAUST
DIAMETER  PLUG ASSEMBLY
BOLT
ALIGNMENT
RIVET  AFT PLUG
1/4 INCH  FORWARD
DIAMETER  ‚PLUG
BOLT
AFT PLUG
ALIGNMENT
RIVET
FIGURE 5: TURBINE EXHAUST PLUG ASSEMBLY BOLTS - GENERAL VISUAL INSPECTION
(SHEET 1 OF 2)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
Work - See page 1 for details.  49 of 63

### Page 50

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each engine.
More DataQtyIdentificationNameTaskStep
by general visual in-
spection, at the for-
ward and aft plug in-
terface, to find if
3/16 inch diameter
bolts and/or 1/4 inch
diameter bolts are
used at the forward
and aft plug inter-
face.
33123423-3-1 OR
BACB30UU4-1
BOLTInspect1
FIGURE 5: TURBINE EXHAUST PLUG ASSEMBLY BOLTS - GENERAL VISUAL INSPECTION
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
50 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 51 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
) AFT PLUG
234€0
FORWARD
PLUG
FORWARD AND AFT PLUG
J) RIVETS
FORWARD PLUG
1/4 INCH DIAMETER HOLE
(33 LOCATIONS, MAXIMUM)
EXISTING NUTPLATE RIVET
HOLES (2 LOCATIONS)
NUTPLATE
(33 LOCATIONS, MAXIMUM)
TYPICAL  2113928
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
FIGURE 6: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL REMAINING 3/16 INCH
DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 1 OF 4)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-78-0051
Work - See page 1 for details.  51 of 63

### Page 52

More DataQtyIdentificationNameTaskStep
Use 3/16 inch diame-
ter fastener, ST30-
7216A-200-216-1.0
('Wedgelock') or
equivalent, in the in-
terface holes of the
aft plug and the for-
ward plug, that do
not have a nutplate.
Or, use 1/4 inch di-
ameter fasteners in
the interface holes
of the aft plug and
the forward plug that
have a nutplate. (a)
5-FASTENERInstall (Temporary)1
WARNING: USE CARE WHEN DRILLING IN TITANIUM. SMALL PARTICLES AND FINE SHAVINGS OF
TITANIUM ARE HIGHLY FLAMMABLE. WATER WITH HOT TITANIUM CAN CAUSE A STEAM
EXPLOSION. EXTINGUISH ALL FIRES OF TITANIUM WITH FULLY DRY TALC, CALCIUM
CARBONATE, SAND, OR GRAPHITE. APPLY THE POWDER TO A DEPTH OF ONE-HALF
INCH OR MORE OVER THE BURNING METAL. DO NOT USE FOAM, WATER, CARBON
TETRACHLORIDE, OR CARBON DIOXIDE. IF YOU DO NOT OBEY, YOU CAN CAUSE INJURY
TO PERSONS.
to 1/4 inch diameter,
Class III hole. Use
Step Reamer part
number ST1864R-
2820-2550-4-221-4-
64-2-4, or equiva-
lent, between the
first and fifth 'wedge-
locks', or first and
fifth 1/4 inch diame-
ter temporary fasten-
ers, to remove dam-
age up to the repair
limit, or to increase
its diameter to 1/4
inch. (b)
1-HOLEReam2
by general visual in-
spection, to make
sure there is no
damage.
1-HOLEInspect3
into the repaired or
increased diameter
hole. (a)
1ST30-7216A-200-279-
1.0 ('WEDGELOCK')
OR EQUIVALENT
1/4 INCH DIA FASTEN-
ER
Install (Temporary)4
FIGURE 6: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL REMAINING 3/16 INCH
DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 2 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
52 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 53

More DataQtyIdentificationNameTaskStep
3/16 inch diameter
fasteners, ST30-
7216A-200-216-1.0
('Wedgelock') or
equivalent, that were
temporarily installed.
Or, 1/4 inch diame-
ter fasteners that
were temporarily in-
stalled. (a)
5-FASTENERRemove / Keep5
1/4 inch diameter
fasteners, ST30-
7216A-200-279-1.0
('Wedgelock') or
equivalent, that were
temporarily installed.
Or, 1/4 inch diame-
ter fasteners that
were temporarily in-
stalled.
32-FASTENERRemove6
1314W5520-3 OR
314W5520-20
AFT PLUGRemove / Keep
as necessary, at all
remaining locations
that do not have nut-
plates for 1/4 inch
diameter bolts, on
the inner circumfer-
ence of the forward
plug, using the exist-
ing rivet holes.
-BACN11G4DE1FNUTPLATEInstall (New)7
as necessary, two
for each nutplate. (c)
-MS20427M3-4RIVETInstall (New)
FIGURE 6: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL REMAINING 3/16 INCH
DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 3 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
53 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 54

More DataQtyIdentificationNameTaskStep
(a) Do not install the 'wedgelocks' (or equivalent 3/16 inch diameter temporary fasteners) or temporary 1/4
inch diameter fasteners in a continuous sequence. Install the first 'wedgelock', in the hole located sequen-
tially next to the hole that is found to have the largest damage or that is remaining at 3/16 inch diameter,
or install the first temporary fastener in the equivalently located 1/4 inch diameter hole. Install the second
'wedgelock' in the hole nearest to the circumferential opposite of the first 'wedgelock' installed, or install
the second temporary fastener in the equivalently located 1/4 inch diameter hole. Install the third
'wedgelock' in the hole nearest to the circumferential midpoint between the first and second 'wedgelocks',
or install the third temporary fastener in the equivalently located 1/4 inch diameter hole. Install the fourth
'wedgelock' in the hole nearest to the circumferential opposite as the third installed 'wedgelock', or install
the fourth temporary fastener in the equivalently located 1/4 inch diameter hole. Install the fifth 'wedgelock'
in the hole located sequentially next to the hole that to has the largest damage, or install the fifth temporary
fastener in the equivalently located 1/4 inch diameter hole. After the hole is reamed and no damage is
found, install a 1/4 inch 'wedgelock' in the repaired or increased diameter hole. Move the first thru fifth
'wedgelocks', or the first thru fifth 1/4 inch diameter temporary fasteners clockwise or counter-clockwise
to repair the hole with the next largest damage and/or increase its diameter to 1/4 inch, until 5 'wedgelocks'
cannot be installed because 1/4 inch diameter wedgelocks or 1/4 inch diameter temporary fasteners are
installed. Do steps 1 thru 5 again to repeat this process until 32 fastener holes are filled with 1/4 inch di-
ameter 'wedgelocks' or 1/4 inch diameter temporary fasteners and all of the 33 fastener holes are repaired
and/or increased to 1/4 inch diameter. Refer to APPENDIX B for a graphical example of the 'wedgelock'
and/or temporary fastener installation process.
(b) Refer to SOPM 20-10-07 and 777-200 SRM 51-30-01 or 777-300 SRM 51-30-01 Section 5, as an accepted
procedure, to drill or ream titanium.
(c) Refer to 777-200 SRM 51-40-02 or 777-300 SRM 51-40-02 as an accepted procedure.
FIGURE 6: TURBINE EXHAUST PLUG ASSEMBLY - REPLACEMENT OF ALL REMAINING 3/16 INCH
DIAMETER BOLTS WITH 1/4 INCH DIAMETER BOLTS
(SHEET 4 OF 4)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
54 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 55 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
FORWARD PLUG
12 RIVETS
• 1/4 INCH DIAMETER HOLE
Y2) NUTPLATE
TYPICAL  2113931
FIGURE 7: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD PLUG, 1/4 INCH DIAMETER NUTPLATE
REPLACEMENT
(SHEET 1 OF 2)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
Work - See page 1 for details.  55 of 63

### Page 56

The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each nut plate location of a turbine exhaust plug
assembly.
More DataQtyIdentificationNameTaskStep
Refer to 777-200
SRM 51-40-02 or
777-300 SRM 51-
40-02 as an accept-
ed procedure.
2MS20427M3-4RIVETRemove1
1BACN11G4DE1FNUTPLATERemove
1BACN11G4DE1FNUTPLATEInstall (New)2
Refer to 777-200
SRM 51-40-02 or
777-300 SRM 51-
40-02 as an accept-
ed procedure.
2MS20427M3-4RIVETInstall (New)
FIGURE 7: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD PLUG, 1/4 INCH DIAMETER NUTPLATE
REPLACEMENT
(SHEET 2 OF 2)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
56 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 57 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
AFT PLUG
BOTTOM
DEAD CENTER ---
3 LOCATIONS
FWD  2114505
• FIGURE 8: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD AND AFT PLUG IDENTIFICATION TAG
REPLACEMENT
(SHEET 1 OF 3)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.  57 of 63

### Page 58 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
B
FORWARD PLUG
BOTTOM
DEAD CENTER
3 LOCATIONS
FWD  2117357
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each turbine exhaust plug assembly.
FIGURE 8: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD AND AFT PLUG IDENTIFICATION TAG
REPLACEMENT
(SHEET 2 OF 3)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  PROPRIETARY - Copyright © Unpublished  Export Controlled ECCN: 9E991 - BOEING  777-78-0051
Work - See page 1 for details.  58 of 63

### Page 59

More DataQtyIdentificationNameTaskStep
Refer to 777-200
SRM 51-40-02 or
777-300 SRM 51-
40-02 an accepted
procedure.
6MS20615-4M3RIVETRemove1
that were incorrectly
identified with 'Assy
314W5520-1'.
2314W5520-23IDENTIFICATION TAGRemove
one on the forward
plug and one on the
aft plug. (a)
2314W5520-23IDENTIFICATION TAGInstall (New)2
three for each identi-
fication tag. Refer to
777-200 SRM 51-
40-02 or 777-300
SRM 51-40-02 an
accepted procedure.
(a)
6MS20615-4M3RIVETInstall (New)
(a) Make sure the identification tag is located on the side of the stringer where the distance between the
stringer and the skin chem-milled area is maximum, but with the minimum conditions that there is a 2D
edge margin between the rivets and the edges of the identification tag and that there is a 2D edge margin
between the rivets and the chemically milled area.
FIGURE 8: TURBINE EXHAUST PLUG ASSEMBLY - FORWARD AND AFT PLUG IDENTIFICATION TAG
REPLACEMENT
(SHEET 3 OF 3)
Export Controlled ECCN: 9E991 - BOEING
PROPRIETARY - Copyright © Unpublished
Work - See page 1 for details.
Original Issue: October 23, 2003
777-78-0051Revision 3 August 23, 2012
59 of 63
BOEING SERVICE BULLETIN 777-78-0051

### Page 60 (OCR)

BOEING SERVICE BULLETIN 777-78-0051
FORWARD PLUG  AFT PLUG
TURBINE EXHAUST
PLUG ASSEMBLY
1/4 INCH
DIAMETER BOLT
(33 LOCATIONS)
FORWARD
PLUG
AFT PLUG
ALIGNMENT
RIVET
2114507
The step numbers shown below agree with the numbers shown in the circle symbols in the figure. The QTY
numbers shown below are the number of parts necessary for each engine.
FIGURE 9: TURBINE EXHAUST PLUG ASSEMBLY - INSTALLATION
(SHEET 1 OF 2)
Original Issue: October 23, 2003
Revision 3 August 23, 2012  Export Controlled ECCN: 9E991 - BOEING  PROPRIETARY - Copyright © Unpublished  777-78-0051
Work - See page 1 for details.  60 of 63

The text continues at https://openairdocs.org/service-documents/boeing/sb-777-78-0051/file/ff2cccbea086.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
