# Bombardier Service Bulletin 601R-24-128

Copy: U.S. DOT/FAA - Service Bulletin (2) ("U.S. DOT/FAA - Service Bulletin (2)"), 25 pages: PDF https://openairdocs.org/files/sha256/c2/b2/c2b258962aee42464915460661a12f7b94077f2ba8526e092275e0dc8b063133; text https://openairdocs.org/service-documents/bombardier/601r-24-128/file/c2b258962aee.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2010-0703; AD 2011-06-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 601R-24-128
- Latest revision known: 601R-24-128, Revision C, dated May 14, 2010 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/601r-24-128

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2011-06-08](https://openairdocs.org/ad/2011-06-08.md), effective Apr 26, 2011: Revisions A, B and C

## Text (25 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2010-0703; AD 2011-06-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB 601R- - - 24- - - 128
Page 1 of 1
May 14/2010
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
CL- - -600- - -2B19Canadair Regional Jet (CRJ) Aircraft
SERVICE BULLETIN 601R - - -24 - - -128
SUBJECT : Electrical Power - - - Air Driven Generator (ADG) - - - Replacement of the Wire
Cable and Backshell of ADG Mating Connector P1XC
This page transmits:
Revision C of Service Bulletin 601R- - - 24- - - 128,
pages 1 thru 23, dated May 14/2010
The changes in this revision have no effect on aircraft that have
incorporated a previous issue of this service bulletin.
Reason:
Revised Accomplishment Instructions, paragraph 2., to:
Correct typing mistakes.
This revision also includes small editorial changes that do not have an effect on the technical
content.
Instructions:
Discard the copy of Service Bulletin 601R- - - 24- - - 128, Revision B, dated Apr 16/ 2009.
Replace with the copy attached.
Service Bulletin History:
Initial issue, dated Sep 17/2009.
Revision A, dated Nov 27/2009.
Revision B, dated Apr 16/2009.
1

### Page 2

SB 601R- - - 24- - - 128
Page 1 of 23
Sep 17/2009
Revision C, May 14/2010
SERVICE BULLETIN
T echnical
Publications
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS LEASED
HAS SOLD AIRCRAFT OR TRANSFERRED SPARES IN THE LAST SIX MONTHS, THIS SERVICE
BULLETIN MUST BE SENT TO THE NEW OWNER, UNLESS CONFIRMATION WAS RECEIVED
THAT BOMBARDIER COMMERCIAL AIRCRAFT HAS INCLUDED THE NEW OPERATOR
AIRCRAFT , THIS SERVICE BULLETIN MUST BE SENT TO THE LESSEE. IF THE OPERATOR
ON THE DISTRIBUTION LIST .
ATA SYSTEM: 24- - -23 NUMBER: 601R - - -24- - -128
SUBJECT : Electrical Power - - - Air Driven Generator (ADG) - - - Replacement of the Wire
Cable and Backshell of ADG Mating Connector P1XC
1. PLANNING INFORMATION
A. Effectivity
(1) Aircraft Affected:
Service Bulletin: CL- - - 600- - - 2B19 Canadair Regional Jet (CRJ) Aircraft Serial
Numbers 7305 thru 7990, 8000 thru 8107.
Production: This change will be incorporated before delivery on Aircraft
Serial Numbers 8108 and subsequent.
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Service Bulletin(s). Before you do this
bulletin, examine all STC, STA or e quivalent action changes to make
sure this bulletin can be completed.

### Page 3

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 2 of 23
Sep 17/2009
Revision C, May 14/2010
B. Reason
(1) Condition
The wires in the cable of ADG mating connector P1XC (written as connector
P1XC in this service bulletin) are silver-plated. Moisture in the ADG bay can
cause corrosion of the wires. Corrosion of the wires can cause an open
circuit and prevent correct operation of the ADG.
(2) Evidence
This condition was found on three in- - -service aircraft.
(3) Objective/Benefit
This service bulletin gives the procedure to replace the wire cable, the ground
wire, and the backshell of connector P1XC.
The wires of the replacement cable are tin-plated. Incorporation of this
service bulletin will prevent corrosion of the wires in the cable of connector
P1XC.
C. Description
The electrical power is removed from the aircraft. The pilot seat is removed.
Access panels are removed. The flight- - -compartment floor- - -panel is removed.
The ADG is extended. Circuit Breaker Panel 3 (CBP - - -3) is removed. The RH and
the LH forward- - -fuselage access panels are removed. The external service panel
assembly is removed. The aft equipment- - -compartment door is opened.
In the ADG bay, connector P1XC is disco nnected from the ADG. The wire cable
and the backshell of connector P1XC are replaced. A new standoff is installed and
the routing of connector P1XC is changed.
CBP- - -3 is installed. The pilot seat is installed. Connector P1XC is connected to
t h e A D G a n d t h e e x t e r n a l s e r v i c e --- p a n e l a s s e m b l y i s i n s t a l l e d . R e t u r n --- t o --- s e r v i c e
tests are done. The RH and the LH forward- - -fuselage access panels are installed.
T h e f l i g h t --- c o m p a r t m e n t f l o o r --- p a n e l i s i n s t a l l e d . T h e a f t e q u i p m e n t --- c o m p a r t m e n t
door is closed. The access panels are installed.

### Page 4

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 3 of 23
Sep 17/2009
Revision C, May 14/2010
D. Compliance
Recommended Service Bulletin. Bombardier recommends that this service bulletin
be done as shown on the table below or no later than six years from the release
date on this service bulletin, unless otherwise directed by the airworthiness
authority of the operator.
AIRCRAFT ACCUMULATED
FLIGHT HOURS
TIME LIMIT TO DO THIS SERVICE
BULLETIN
15000 or more 6000 flight hours
Less than 15000 12000 flight hours
NOTE: This service bulletin must be incorporated on all aircraft, including
parked aircraft.
This Service Bulletin does not affect Airworthiness Limitations (AWLs) or Damage
T olerance Inspections (DTIs).
E. Approval
The technical content of this service bulletin has been approved under the authority
of the TCCA Design Approval Organization No: DAO #93- - -Q- - -02.
F. M a n p o w e r
The man hours given below are an estimate for direct labor done by an
experienced crew on an aircraft prepared for maintenance.
This estimate does not include the time necessary for:
− Administrative functions such as planning, liaison, familiarization, and report writing.
− Non productive elapsed time such as rest time, having meals, and crew shift
changes.
− Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
− Preparation for modification (unless specified in the accomplishment
instructions) such as cleaning and getting parts, tools, consumables, and
ground equipment.
− Quality assurance inspections, troubleshooting and/or correction of
discrepancies found when a task is done.
− All other activities that are not considered by Bombardier as directly related to
the accomplishment of this procedure.

### Page 5

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 4 of 23
Sep 17/2009
Revision C, May 14/2010
It will take an estimated 9.50 man- - -hours to complete this service bulletin. The
man- - - hours are divided as shown in the table that follows:
TASK M A N --- H O U R S
( 1 ) J o b S e t --- U p 0.50
(2) Procedure 8.00
(3) T est 0.25
(4) Job Close- - -Out 0.75
NOTE: For on- - -site labor assistance, please speak with a Fleet Services
representative for a quote. The Fleet Services Team can be
contacted via the CRC at 514- - - 855- - - 8500 or email at
thd.crj@aero.bombardier.com.
G. Material - - - Price and Availability
(1) The kit in the table that follows is available from Bombardier Commercial
Aircraft.
NOTE: For a list of the kit contents, refer to paragraph 3.A.
For Aircraft that have not incorporated a previous issue of this service bulletin and
that have not yet ordered kits
KIT NUMBER NAME
601R24- - - 128K1A ADG Power Cable Replacement Kit
For Aircraft 7305 thru 7884, 7886 thru 7913, 7915 thru 7924, 7926 thru 7931, 7933
that have not incorporated a previous issue of this service bulletin but that have
ordered kit 601R24 - - -128K1
KIT NUMBER NAME
601R24- - - 128K2 Plate K601R50195- - - 2007

### Page 6

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 5 of 23
Sep 17/2009
Revision C, May 14/2010
(2) Please send a purchase order to the address below to schedule the kit(s):
Bombardier
Service Bulletin Kit Support T eam
123 Garratt Blvd, N42- - - 24
T oronto, Ontario
Canada M3K 1Y5
Fax: 416- - - 375- - - 3060
Phone: 416- - - 375- - - 3920
Email: sbkits@aero.bombardier.com
Please contact the Service Bulletin Kit Support T eam at the address above for
terms and conditions.
(3) Refer to paragraph 3.B. for a list of consumables for this service bulletin.
H. T ooling - - - Price and Availability
There are no tool kits for this service bulletin.
Refer to paragraph 3.C. for a list of special tools and equipment for this service
bulletin.
I. Weight and Balance
Not changed.
J. Electrical Load Data
Not changed.
K. References
Restriction and/or Special Instruction (RSI) C- - -A235, Revision A.
Modification Summary TC601R17827, Revision C.
Aircraft Maintenance Manual, CSP A- - - 001.
Structural Repair Manual, CSP A- - - 008.
Electrical/Electronic Components - Standard Practices Manual (ESPM), CSP A-115.
For Bombardier reference only: PCA 05932.

### Page 7

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 6 of 23
Sep 17/2009
Revision C, May 14/2010
L. Other Publications Affected
Wiring Diagram Manual (WDM) CSP A- - - 003.......................
Illustrated Parts Catalog (IPC) CSP A- - -006........................
M. Relationship Chart
PRE - - -SB
PART NUMBER NAME POST - - -SBPART NUMBER NAME
M85049/53- - - 22W
or
450AS005M22
Backshell M85049/43S22W Backshell

### Page 8

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 7 of 23
Sep 17/2009
Revision C, May 14/2010
2. ACCOMPLISHMENT INSTRUCTIONS
A . J o b S e t --- U p
Reference Information
REFERENCE DESIGNATION
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 2 Lockwire - - - Maintenance Practices
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 3Safety Cable - - - Maintenance Practices
A M M 2 4 --- 0 0 --- 0 0 --- 8 6 1 --- 8 0 2Remove Electrical Power to the Aircraft
A M M 2 4 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1Electrical/Electronic Safety Precautions
A M M 2 4 --- 0 2 --- 3 0 --- 0 0 0 --- 8 0 1Removal of Circuit Breaker Panel CBP- - -3
A M M 2 4 --- 0 2 --- 3 0 --- 4 0 0 --- 8 0 1Installation of Circuit Breaker Panel CBP- - -3
A M M 2 4 --- 2 3 --- 0 1 --- 7 2 0 --- 8 0 3 Functional T est of the Dry ADG
A M M 2 4 --- 2 3 --- 0 1 --- 8 4 0 --- 8 0 4 Manual Lowering of the Dry ADG
A M M 2 4 --- 2 3 --- 0 1 --- 8 4 0 --- 8 0 5Retraction of the Dry ADG After Deployment
A M M 2 4 --- 2 4 --- 0 1 --- 0 0 0 --- 8 0 1Removal of the External Service- - -Panel
Assembly
A M M 2 4 --- 2 4 --- 0 1 --- 4 0 0 --- 8 0 1Installation of the External Service- - -Panel
Assembly
A M M 2 4 --- 2 4 --- 0 1 --- 7 1 0 --- 8 0 1Operational T est of the External Service- - -Panel
Assembly
A M M 2 5 --- 1 1 --- 0 1 --- 0 0 0 --- 8 0 1 Removal of the Pilot/Copilot Seat
A M M 2 5 --- 1 1 --- 0 1 --- 4 0 0 --- 8 0 1 Installation of the Pilot/Copilot Seat
A M M 5 1 --- 3 1 --- 0 0 --- 9 9 0 --- 8 0 1 Consumable Materials
A M M 5 3 --- 1 0 --- 3 4 --- 0 0 0 --- 8 0 1Removal of the Forward - - - Fuselage Access
Panels
A M M 5 3 --- 1 0 --- 3 4 --- 4 0 0 --- 8 0 1Installation of the Forward- - -Fuselage Access
Panels
E S P M 2 0 --- 1 1 --- 0 0 Wire Stripping and Wire/Cable Damage Repair
- - - Maintenance Practices

### Page 9

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 8 of 23
Sep 17/2009
Revision C, May 14/2010
REFERENCE DESIGNATION
E S P M 2 0 --- 1 2 --- 0 0 Wiring - - - Removal/Installation
E S P M 2 0 --- 1 2 --- 0 1 Electrical Wiring - - - Continuity T esting
E S P M 2 0 --- 1 7 --- 1 0 Electrical Connectors - - - Maintenance Practices
E S P M 2 0 --- 2 0 --- 0 0 T erminal Lugs - - - Removal/Installation
S R M 5 1 --- 2 1 --- 1 1 Corrosion Prevention Procedures
S R M 5 1 --- 2 3 --- 0 0 Pressure, Environmental, Fuel T ank and Firewall
Sealing
S R M 5 1 --- 2 6 --- 0 0 Cleaning
S R M 5 1 --- 4 2 --- 0 6 Solid Rivets
T olerance Information
Linear T olerances Angular T olerance
X.XX in. (0.X mm) X.X in. (X mm)
/ 0° 30”+/- - - 0.03 in. +/--- 0.1 in. +/--- 0° 30”
+ / --- 0 . 8 m m + / --- 3 m m
NOTE: The tolerances above apply to the dimensions given in this service
bulletin except if specified differently.
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT . IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(1) Obey all the electrical/electronic safety precautions
(Refer to AMM 24- - - 00- - - 00- - - 910- - - 801).
(2) Remove electrical power from the aircraft
(Refer to AMM 24- - - 00- - - 00- - - 861- - - 802).
(3) Open the aft equipment- - -compartment door .

### Page 10

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 9 of 23
Sep 17/2009
Revision C, May 14/2010
(4) Open, safety, and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 2 N6 ADG DEPLOY CONT AUTO 222
C B P --- 2 N7 ADG DEPLOY CONT MAN 222
C B P --- 5 B10 ADG AUTO 311
C B P --- 5 B11 ADG MAN 311
C B P --- 5 B12 EXT PWR 311
(5) Remove the external service panel (Refer to AMM 24- - - 24- - - 01- - - 000- - - 801).
(6) Manually lower the dry ADG (Refer to AMM 24- - - 23- - - 01- - - 840- - - 804).
(7) Remove the pilot seat (Refer to AMM 25- - - 11- - - 01- - - 000- - - 801).
(8) Remove access panels 221BZ and 222BZ.
(9) Remove CBP - - - 3 (Refer to AMM 24- - - 02- - - 30- - - 000- - - 801).
(10) If necessary, remove the cover of Junction Box (JB) 6.
(11) Remove floor panel 221ALF .
(12) Remove forward-fuselage access-panels 131AL and 132AL
(Refer to AMM 53- - - 10- - - 34- - - 000- - - 801).

### Page 11

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 10 of 23
Sep 17/2009
Revision C, May 14/2010
B. Procedure
Refer to Figure 1.
(1) Remove and discard the wire cable between connector P1XC and
C B P --- 3 --- T B 2 a s f o l l o w s :
(a) Disconnect connector P1XC from the ADG.
(b) Remove the screw (12), the washer (11), and the clamp (10) that attach
the wire bundle of connector P1XC to the spacer nutplate (16). Keep the
clamp (10), the washer (11), and the screw (12).
(c) Disconnect and remove all the wires from connector P1XC with an
extraction tool.
(d) Loosen and remove the backshell (4) from connector P1XC. Keep
connector P1XC.
(e) Remove the nut (14) and the washer (13) that attach wire XC51A8N to
ground stud N792 (9). Keep the nut (14) and the washer (13).
(f) Disconnect, remove, and discard wire XC51A8N from ground stud N792
( 9 ) ( R e f e r t o E S P M 2 0 --- 1 1 --- 0 0 ) .
(g) Cut the lockwire or safety cable and loosen the mounting nut of
bulkhead feedthru FT202- - -D to help removal and installation of the
wires.
(h) In the forward avionics compartment and in the flight compartment,
carefully remove the clamps that attached the wire cable of connector
P1XC. Keep all protective sleeving, cable clamps, and their mounting
hardware.
(i) Cut, remove, and discard the wire cable of connector P1XC
(Refer to ESPM 20- - - 11- - - 00).
Refer to Figure 2.
(j) In CBP - - -3 (1), remove and keep the cover assembly (3) from T erminal
Block TB2 (2).
(k) Remove and keep the nuts (4) and the washers (5) that attach the
terminal lugs (9) to the studs of TB2 (2).
(l) Remove wires XC1A8AWHT (6), XC2A8BBLU (7), and XC3A8CORN (8)
from TB2 (2) (Refer to ESPM 20- - - 11- - - 00).

### Page 12

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 11 of 23
Sep 17/2009
Revision C, May 14/2010
For Aircraft 7885, 7914, 7925, 7932, and 7934 thru 8107
Refer to Figure 1 (Sheet 3 of 4).
(2) In the ADG bay, install the spacer nutplate (7) as follows:
(a) Drill one hole to a diameter of 0.128- - - 0.132 in. (3.25- - - 3.35 mm) at 7.95
in. (20.19 cm) above the bracket and 0.32 in. (8.13 mm) inboard of the
outboard edge of the stiffener.
(b) Put the spacer nutplate (7) in position with a temporary fastener .
(c) Backdrill one hole to a diameter of 0.128- - - 0.132 in. (3.25- - - 3.35 mm)
from the spacer nutplate (7) through the stiffener.
(d) Remove the burrs.
(e) Clean the work area with solvent (Refer to SRM 51- - - 26- - - 00).
(f) Apply chemical conversion coating to the bare metal areas
( R e f e r t o S R M 5 1 --- 2 1 --- 1 1 ) .
(g) Apply faying surface sealant to the mating surfaces of the spacer
nutplate (7) and the stiffener (Refer to SRM 51- - - 23- - - 00).
(h) Install the spacer nutplate (7) with wet- - - installed rivets (8)
( R e f e r t o S R M 5 1 --- 2 3 --- 0 0 a n d S R M 5 1 --- 4 2 --- 0 6 ) .
For Aircraft 7305 thru 7884, 7886 thru 7913, 7915 thru 7924, 7926 thru 7931, and
7933
Refer to Figure 1 (Sheet 4 of 4).
(3) In the ADG bay, install the spacer nutplate (7) and plate (18) as follows:
(a) At 8.15 in. (20.7 cm) from the bracket, remove the rivet from the inboard
of the outer edge of the stiffener (Refer to SRM 51- - - 42- - - 06).
(b) Remove the rivet that is above the rivet removed in the previous step
( R e f e r t o S R M 5 1 --- 4 2 --- 0 6 ) .
(c) T emporarily install the plate (18) on the stiffener.

### Page 13

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 12 of 23
Sep 17/2009
Revision C, May 14/2010
(d) Backdrill two holes to a diameter of 0.160- - - 0.164 in. (4.06- - - 4.17 mm)
from the holes of the removed rivets on the stiffener to the plate
( R e f e r t o S R M 5 1 --- 4 2 --- 0 6 ) .
(e) T emporarily install the spacer nutplate (7) on the plate (18).
(f) Backdrill two holes to a diameter of 0.128- - - 0.132 in. (3.25- - - 3.35 mm)
from the spacer nutplate (7) through the plate (18)
( R e f e r t o S R M 5 1 --- 4 2 --- 0 6 ) .
(g) Remove the spacer nutplate (7) and the plate (18).
(h) Remove the burrs.
(i) Clean the work area with solvent (Refer to SRM 51- - - 26- - - 00).
(j) Apply chemical conversion coating to the bare metal areas
( R e f e r t o S R M 5 1 --- 2 1 --- 1 1 ) .
(k) Apply faying surface sealant to the mating surfaces of the spacer
nutplate (7) and the plate (18) (Refer to SRM 51- - - 23- - - 00).
(l) Install the spacer nutplate (7) with wet- - - installed rivets (8)
( R e f e r t o S R M 5 1 --- 2 3 --- 0 0 a n d S R M 5 1 --- 4 2 --- 0 6 ) .
(m) Apply faying surface sealant to the mating surfaces of the plate (18) and
the stiffener (Refer to SRM 51- - -23- - -00).
(n) Install the plate (18) with wet- - -installed rivets (19)
( R e f e r t o S R M 5 1 --- 2 3 --- 0 0 a n d S R M 5 1 --- 4 2 --- 0 6 ) .
For all Aircraft
Refer to Figures 1 and 2.
( 4 ) I n s t a l lt h et h en e ww i r ec a b l ea n dg r o u n dw i r ea ss h o w ni nt h et a b l eb e l o w :
WIRE FROM TERMINAL TO TERMINAL W ¡
XC1A8AWHT P 1 X C --- A M39029/29- - - 214 C B P --- 3 --- T B 2 --- 1MS25036- - - 115 1J
XC2A8BBLU P 1 X C --- B M39029/29- - - 214 C B P --- 3 --- T B 2 --- 2MS25036- - - 115 1J
XC3A8CORN P 1 X C --- C M39029/29- - - 214 C B P --- 3 --- T B 2 --- 3MS25036- - - 115 1J
XC51A8N P 1 X C --- D M39029/29- - - 214 N792 MS25036- - - 118 ---
¡ Wire separation “W” code.
(a) In the forward avionics compartment, install the new cable with the
c l a m p s ,t h es c r e w s ,a n dt h ew a s h e r s .
.

### Page 14

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 13 of 23
Sep 17/2009
Revision C, May 14/2010
( b ) C u tt h ew i r e so ft h en e wc a b l et ot h ec o r r e c tl e n g t h
(Refer to ESPM 20- - - 11- - - 00).
(c) Remove the insulation from the wire ends with a wire stripper
(Refer to ESPM 20- - - 11- - - 00).
(d) Install the applicable terminal lugs on the wires of the new cable with a
crimping tool (Refer to ESPM 20- - - 17- - - 10).
(e) Install the terminal lugs (9) on the studs of TB2 (2) with the washers (5)
and the nuts (4).
(f) T orque the nut (4) (Refer to ESPM 20- - - 20- - - 00).
(g) Put the wires of the new cable through bulkhead feedthru FT202- - -D from
the right access hole.
(h) Tighten bulkhead feedthru FT202- - - D and install the lockwire or safety
cable (Refer to AMM 20- - - 24- - - 00- - - 910- - - 803).
(i) Remove and discard the supplied screws and lock washers from the
saddle clamp of the new backshell (4). Keep the saddle clamp.
(j) Put the wires for connector P1XC through the sleeve (5), the
identification sleeve (6), and the new backshell (4).
( k ) C u tt h ew i r e so ft h en e wc a b l et ot h ec o r r e c tl e n g t h
(Refer to ESPM 20- - - 11- - - 00).
NOTE: The length of the wire cable between the backshell (4) of connector
P1XC and the new spacer nutplate must be 13 in. (33 cm).
(l) Remove the insulation from the wire ends with a wire stripper
(Refer to ESPM 20- - - 11- - - 00).
(m) Install the applicable terminal on the wires of the new cable with a
crimping tool (Refer to ESPM 20- - - 17- - - 10).
(n) Install the wires of the new cable in connector P1XC with an insertion
t o o l a t t h e g i v e n l o c a t i o n s ( R e f e r t o E S P M 2 0 --- 1 7 --- 1 0 ) .
(o) Cut new wire XC51A8N to the correct length
(Refer to ESPM 20- - - 11- - - 00).

### Page 15

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 14 of 23
Sep 17/2009
Revision C, May 14/2010
(p) Install the terminal lug (15) on new wire XC51A8N with a crimping tool
(Refer to ESPM 20- - - 17- - - 10).
(q) Install the terminal lug (15) of wire XC51A8N to ground stud N792 (9)
with the washer (13), the lock washer (17), and the nut (14).
(r) T orque the nut (14) (Refer to ESPM 20- - - 20- - - 00).
(s) Do a continuity check of the installed wires (Refer to ESPM 20- - - 12- - - 01).
(t) Connect connector P1XC to the ADG.
(u) Put the backshell (4) of connector P1XC at the 8 o’clock position
(Refer to Figure 1, View C).
(v) Tighten and torque the backshell (4) (Refer to ESPM 20- - - 17- - - 10).
(w) Attach the wire bundle to the backshell (4) of connector P1XC as follows:
1 Apply four to eight turns of fiberglass tape around the wire bundle.
2 I n s t a l lt h es a d d l ec l a m po nt h et a p e da r e ao ft h ew i r eb u n d l ew i t h
the screws (1), the lock washers (2), and the washers (3).
NOTE: T h et a p e da r e ao ft h ew i r eb u n d l em u s tn o tm o v ei n s i d et h e
saddle clamp and there must be no tension on the terminals
and wires.
WARNING: DO NOT TOUCH THE HEAT GUN REFLECTOR. THE HEAT GUN
REFLECTOR CAN GET VERY HOT AND CAUSE INJURY IF YOU
TOUCH IT .
(x) With a heat gun, apply heat to shrink the identification sleeve (6)
(Refer to ESPM 20- - - 17- - - 10).
(5) Install the external service panel (Refer to AMM 24- - - 24- - - 01- - - 400- - - 801).
(6) Attach the bundle of connector P1XC to the new spacer nutplate (7) with the
clamp (10) the washer (11) and the screw (12).
( 7 ) M a k es u r et h a tt h el e n g t ho ft h ew i r ec a b l eb e t w e e nt h eb a c k s h e l l( 4 )o f
connector P1XC and the clamp (10) is 13 in. (33 cm).
(8) Safety connector P1XC to the adjacent screw with lockwire or safety cable
(Refer to AMM 20- - - 24- - - 00- - - 910- - - 803).

### Page 16

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 15 of 23
Sep 17/2009
Revision C, May 14/2010
Connector P1XC and Backshell - - - Wiring Changes
F i g u r e1( S h e e t1o f4 )
rsb601r24128_001.dg
A
A
B
B
13.0 in. (33.0 cm)
B
1
2
3
LEGEND
PRE- -MOD
XC1A8AWHT
XC2A8BBLU
XC3A8CORN
AIR DRIVEN
GENERATOR
C
B
A
P1XC
G1XC FS193L
N792
XC51A8ND
XC1A8AWHT
XC1A8BBLU
XC1A8CORN
CLAMP
13.0 in. (33.0 cm)
W1J FS202L
FT202- -D
22
1
3
CBP- -3 FS230L
1. Screw MS35206- -246.
2. Lock washer MS35338- -42.
3. Washer NAS1149DN816J.
4. Connector M85049/43S22W.
5. Sleeve S10155E8.
6. Identification sleeve.
4
P1XC
65
P1XC
POST- -MOD
4
SADDLE CLAMP
(REF)

### Page 17

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 16 of 23
Sep 17/2009
Revision C, May 14/2010
Connector P1XC - - - Backshell Position
F i g u r e1( S h e e t2o f4 )
rsb601r24128_002.dg
A
12 O’CLOCK
3 O’CLOCK9 O’CLOCK
6 O’CLOCK
C
C
A
BACKSHELL
POSITION
8 O’CLOCK

### Page 18

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 17 of 23
Sep 17/2009
Revision C, May 14/2010
Spacer Nutplate - - - Installation
F i g u r e1( S h e e t3o f4 )
rsb601r24128_004.dg, eg, mar 29/2010
C
7.95 in. (20.19 cm)
7
8
10 11 12
D
16
WIREXC51A8N
(REF)
1
STIFFENER
(REF)
BRACKET
(REF)
0.32 in. (8.1 mm)
NOTE
Installation of the clamp 10
on spacer nutplate 16 (pre- -mod),
and on spacer nutplate 7 (post- -mod).
1
A
For Aircraft
7885, 7914, 7925,
7932 and 7934- -8107.
LEGEND
7. Spacer nutplate B0204040AL- -5W.
8. Rivet MS20470AD4- -5A.
9. Ground stud N792.
10. Clamp.
11. Washer.
12. Screw.
13. Washer.
14. Nut.
15. T erminal lug
MS25036- -118.
16. Spacer nutplate.
17. Lock washer.
E
E
15 13 17 149
D

### Page 19

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 18 of 23
Sep 17/2009
Revision C, May 14/2010
Spacer Nutplate - - - Installation
F i g u r e1( S h e e t4o f4 )
15 13 17 149
D
C
8.15 in. (20.7 cm)
7
8
10 11 12
D
16
WIREXC51A8N
(REF)
1STIFFENER
(REF)
BRACKET
(REF)
NOTE
Installation of the clamp 10
on spacer nutplate 16 (pre- -mod),
and on spacer nutplate 7 (post- -mod).
1
19
18
For Aircraft
7305- -7884, 7886- -7913,
7915- -7924, 7926- -7931, 7933.
LEGEND
7. Spacer nutplate B02040AL- -5W.
8. Rivet MS20470AD4- -5A.
9. Ground stud N792.
10. Clamp.
11. Washer.
12. Screw.
13. Washer.
14. Nut.
15. T erminal lug
MS25036- -118.
16. Spacer nutplate.
17. Lock washer.
18. Plate K601R50195- -2007SB.
19. Rivet MS20470AD5- -6A.
E
E
A
rsb601r24128_003.dg, eg, mar 29/2010

### Page 20

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 19 of 23
Sep 17/2009
Revision C, May 14/2010
Circuit Breaker Panel 3 - - - Wiring Changes
Figure 2
rsb601r24128_003.dg, yf, 24/07/09
LEGEND
2
1
9
3
7
8
1. CBP- -3.
2. T erminal block TB2.
3. Cover assembly.
4. Nut.
5. Washer.
6. Wire XC1A8AWHT .
7. Wire XC2A8BBLU.
8. Wire XC3A8CORN.
4
5
A
B
B
A
6
9
9. T erminal lug MS25036- -115.

### Page 21

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 20 of 23
Sep 17/2009
Revision C, May 14/2010
C . J o b C l o s e --- O u t
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Install circuit breaker panel CBP - - - 3 (Refer to AMM 24- - - 02- - - 30- - - 400- - - 801).
(3) Install the cover of JB- - -6.
(4) Do the retraction of the ADG after deployment
(Refer to AMM 24- - - 23- - - 01- - - 840- - - 805).
(5) Make sure that the wire bundle of connector P1XC does not touch the aircraft
structure or installed components.
(6) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 2 N6 ADG DEPLOY CONT AUTO 222
C B P --- 2 N7 ADG DEPLOY CONT MAN 222
C B P --- 5 B10 ADG AUTO 311
C B P --- 5 B11 ADG MAN 311
C B P --- 5 B12 EXT PWR 311
(7) Do the operational test of the external service panel
(Refer to AMM 24- - - 24- - - 01- - - 710- - - 801).
(8) Do the functional test of the dry ADG (Refer to AMM 24- - - 23- - - 01- - - 720- - - 803).
NOTE: The wire bundle of connector P1XC must not touch the aircraft structure
or installed components.
(9) Install floor panel 221ALF .
(10) Install access panels 221BZ and 222BZ.
(11) Install forward- - - fuselage access panels 131AL and 132AL
(Refer to AMM 53- - - 10- - - 34- - - 400- - - 801).
(12) Install the pilot’s seat (Refer to AMM 25- - - 11- - - 01- - - 000- - - 801).
(13) Close the aft equipment- - - compartment door.
(14) When this service bulletin is completed, make this entry in the applicable
logbook(s): “Service Bulletin 601R- - - 24- - - 128, Revision C, Electrical Power - - -
Air Driven Generator (ADG) - - - Replacement of the Wire Cable and Backshell
of ADG Mating Connector P1XC, incorporated.”

### Page 22

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 21 of 23
Sep 17/2009
Revision C, May 14/2010
3. MATERIAL INFORMATION
A. Kit Information
KIT 601R24 - - -128K1A
PART NUMBER QUANTITY NAME ALTERNATEPARTS NOTES
601R24- - - 128K100 1 Wire kit --- ---
601R24- - - 128K101 1 Sleeve kit --- ---
B0204040AL- - - 5W 1 Spacer nutplate --- ---
K601R50195-2007SB 1 Plate --- ---
M39029/29- - - 214 4 Contact --- ---
M85049/43S22W 1 Backshell --- ---
MS20470AD4- - - 5A 2 Solid rivet --- ---
MS20470AD5- - - 6A 2 Solid rivet --- ---
MS25036- - - 115 3 Te r m i n a l l u g --- ---
MS25036- - - 118 1 Te r m i n a l l u g --- ---
MS35206- - - 246 2 Screw --- ---
MS35338- - - 42 2 Lock washer --- ---
NAS1149DN816J 2 Washer --- ---
S10155E8 1 Sleeve --- ---
KIT 601R24 - - -128K2
PART NUMBER QUANTITY NAME ALTERNATEPARTS NOTES
K601R50195-2007SB 1 Plate --- ---
MS20470AD5- - - 6A 2 Solid rivet --- ---

### Page 23

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 22 of 23
Sep 17/2009
Revision C, May 14/2010
B. Consumable Information
The materials that follow are necessary to do this service bulletin and can be
ordered from Bombardier or purchased directly from industry sources. If the
material is ordered from Bombardier , there can be some lead time because of shelf
life of the material.
CONSUMABLES
SPECIFICATION QUANTITY NAME REFERENCE
MIL- - - C - - - 81706 As necessary Chemical conversion
coating (Alodine 1200S
or equivalent)
05- - - 025¡
MIL- - - I- - - 19166 As necessary T ape, insulating, elect.
high temperature glass
fiber
05- - - 094¡
MS3367, Type I,
Class I
As necessary Strap, tiedown,
electrical components,
adjustable,
self- - -clinching, plastic
05- - - 057¡
MS20995C20 As necessary Lockwire, CRES,
0.020 in. dia.
05- - - 003¡
AS3510- - - 0109C As necessary Cable, safety, 0.020 in.
(0.51 mm) dia.
05- - - 132¡
AS3510- - - 01F As necessary Ferrule, for 0.020 in.
(0.51 mm) dia. safety
cable
05- - - 135¡
¡ R e f e r t o A M M 5 1 --- 3 1 --- 0 0 --- 9 9 0 --- 8 0 1
NOTE: T o complete this list of consumables, refer to the different tasks given as
references in this service bulletin.
C. Special T ools and Equipment
For a list of special tools and equipment, refer to the different tasks given as
references in this service bulletin.

### Page 24

SERVICE BULLETIN 601R- - -24- - -128
SB 601R- - - 24- - - 128
Page 23 of 23
Sep 17/2009
Revision C, May 14/2010
D. Disposition of Parts
The table that follows shows the disposition of installed parts on the aircraft (or
spares), and the relation of installed parts (or spares) to the new parts to be
installed with this service bulletin.
PRE - - -SB
PART NUMBER
NAME QUANTITY DC POST - - -SB
PART NUMBER
NAME
M85049/53- - - 22W
or
450AS005M22
Backshell 1 MUI M85049/43S22W Backshell
Disposition code (DC):
MUI: Multiple Usage Item: Return to stock if serviceable.
1

### Page 25

THANK YOU FOR ANSWERING THIS EVALUATION FORM 
UPON COMPLETION OF THIS EVALUATION FORM/COMPLIANCE SHEET, FAX TO 
450-476-7300 
SERVICE BULLETIN EVALUATION FORM/COMPLIANCE SHEET 
(YOUR IDEAS WILL HELP US PROVIDE BETTER BULLETINS) 
SERVICE BULLETIN : 601R-24-128C  ISSUE: C  
 
 STRONGLY DISAGREE NEUTRAL AGREE STRONGLY 
 DISAGREE    AGREE 
• Instructions to do the Service Bulletin 
were accurate. 
Comments: 
     
• Illustration(s), figure(s), picture(s) and/or 
kit drawing(s) were helpful to carry out 
instructions. 
 Comments: 
     
• If a parts kit was required, did the kit 
contents received agree with the 
contents listed in the bulletin? 
 Comments: 
 
     
• Aircraft hands-on work was 
accomplished in estimated time. 
      Comments: 
     
• Overall, I was satisfied with this Service 
Bulletin. 
 Comments: 
     
PLEASE SUPPLY US WITH THE FOLLOWING DATA AND FAX TO (450) 476-7300: 
OPERATOR:  NAME (Please print)  
SERVICE CENTER:  TELEPHONE:  
AIRCRAFT SERIAL NO.:  FACSIMILE:  
DATE  OF SB 
INCORPOARTION

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
