# MHI RJ Service Bulletin 601R-25-206

Copy: No revision named ("601R-25-206"), 38 pages: PDF https://openairdocs.org/files/sha256/cd/7c/cd7c014c0a13b9d561df04da4f20da480e26fd160f7e10e41d98a85855ce4850; text https://openairdocs.org/service-documents/bombardier/601r-25-206/file/cd7c014c0a13.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-0995, the docket of AD 2024-24-07. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md) (issued as MHI RJ)
- Type: Service bulletin (Service Bulletin)
- Number: 601R-25-206
- Page: https://openairdocs.org/service-documents/bombardier/601r-25-206

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-24-07](https://openairdocs.org/ad/2024-24-07.md), effective Jan 13, 2025: No revision named

## Text (38 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-0995, the docket of AD 2024-24-07. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB 601R-25-206
Page 1 of 38
Jun 29/2023
SERVICE BULLETIN
Technical
Publications
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS LEASED AIRCRAFT ,
TRANSFERRED SPARES IN THE LAST SIX MONTHS, SEND THIS SERVICE BULLETIN TO THE NEW
OWNER, UNLESS CONFIRMATION WAS RECEIVED THAT MHIRJ HAS INCLUDED THE NEW
OPERATOR ON THE DISTRIBUTION LIST .
SEND THIS SERVICE BULLETIN TO THE LESSEE. IF THE OPERATOR HAS SOLD AIRCRAFT OR
ATA SYSTEM: 25-20 NUMBER: 601R-25-206
SUBJECT:  Equipment / Furnishings - Storage Compartment - Replacement of
Overhead Bins Serrated Hooks and Support Tubes and Installation of a
Shear Pin
1. PLANNING INFORMATION
A. Effectivity
(1) Aircraft Affected:
Service Bulletin: CL-600-2B19 CRJ Series aircraft with serial numbers 7673
thru 7683, 7685 thru 7689, 7691 thru 7696, 7698 thru 7703,
7705 thru 7788, 7790 thru 7990, 8000 thru 8042, 8044, 8045,
8047, 8049, 8050, 8058, 8059, 8061, 8062 and 8064.
Production: There is no production effectivity.
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by MHIRJ service bulletins. Before you do this service
bulletin, examine all Supplemental Type Certificates (STCs), and
Supplemental Type Approvals (STAs) or equivalent action changes
to make sure you can complete this service bulletin.

### Page 2

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 2 of 38
Jun 29/2023
B. Reason
(1) Condition
Some overhead storage compartments (written as the overhead bins in this
Service Bulletin) with a serration attachment system could move in case of an
emergency landing (9G load test).
(2) Evidence
The serration attachment system that holds the overhead bins in position on
the serrated outboard tube assemblies did not perform as expected during a
recent 9G load certification test.
(3) Objective/Benefit
This service bulletin gives the procedure to replace the serrated hooks and
support tubes and install a shear pin on the overhead bins.
C. Description
The passenger door is opened. The overhead bins are removed. The applicable
Safran VSB J070000-25-07 or J070000-25-08 or J070000-25-09 or
J070000-25-10 is done to replace the serrated hooks and support tubes. The
overhead bins are installed with a new shear pin. The passenger door is closed.
D. Compliance
Recommended service bulletin.
MHIRJ recommends that this service bulletin be done at no more than 6000 flight
hours or no later than 44 months from the release date on this service bulletin,
whichever comes first, unless otherwise directed by the airworthiness authority of
the operator.
NOTE: If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative
of MHIRJ in the CRC at 450-990-7CRC (450-990-7272) direct,
1-833-990-7CRC (1-833-990-7272) toll free for North America or
+1-450-990-7CRC (+1-450-990-7272) for international callers or
e‐mail at thd.crj@MHIRJ.com for analysis and to get an approved
disposition to complete this service bulletin.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).

### Page 3

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 3 of 38
Jun 29/2023
E. Approval
The technical content of this service bulletin has been approved under the authority
of the TCCA Design Approval Organization No: DAO #20-Q-01.
F . Manpower
The man‐hours given below are estimates for direct labor done by an experienced
crew on an aircraft prepared for maintenance.
These estimates do not include the time necessary for:
-Administrative functions such as planning, liaising, familiarization, and report writing.
-Non‐productive elapsed time such as rest time, having meals, and crew shift
changes.
-Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
-Preparation for modification (unless specified in the Accomplishment
Instructions) such as cleaning and getting parts, tools, consumables, and
ground equipment.
-Quality assurance inspections, troubleshooting and/or correction of
discrepancies found when a task is done.
-All other activities that are not considered by MHIRJ as directly related to the
accomplishment of this procedure.
NOTE: For on‐site labor assistance, please speak with a Fleet Services
representative for an estimate. Call the Fleet Services Team through the
CRC at 450-990-7CRC (450-990-7272) direct, 1-833-990-7CRC
(1-833-990-7272) toll free for North America or +1-450-990-7CRC
(+1-450-990-7272) for international callers or e‐mail at
thd.crj@MHIRJ.com.

### Page 4

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 4 of 38
Jun 29/2023
It will take an estimated 14.75 man‐hours to complete this service bulletin. The
man‐hours are divided in the table that follows (elapsed cure time is not included in
the man‐hour summary given above):
TASK MAN‐HOURS
(1)  Job Set‐Up 0.25
(2)  Procedure 13.5
(3)  Test 0.5
(4)  Job Close‐Out 0.5
NOTE: These estimates do not include the man-hours necessary to do the
Safran Service Bulletins J070000-25-07 or J070000-25-08 or
J070000-25-09 or J070000-25-10.
G. Material - Price and Availability
For aircraft 7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696,
7698, 7699, 7701 thru 7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747
thru 7783, 7786 thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru
7861, 7863, 7865, 7867 thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949,
7951 thru 7957, 7959 thru 7972, 7974, 7976 thru 7980, 7982, 7983, 7985 thru 7988,
8000 thru 8007, 8009, 8011 thru 8042, 8044, 8045, 8047, 8050, 8059 and 8062
Refer to Safran Service Bulletin J070000-25-07.
For Aircraft 7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866,
7901, 7902, 7910, 7915, 7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010,
8058, 8061 and 8064
Refer to Safran Service Bulletin J070000-25-09.
For Aircraft 7676, 7686, 7784 and 7807
Refer to Safran Service Bulletin J070000-25-08.
For Aircraft 8049
Refer to Safran Service Bulletin J070000-25-10.
For all aircraft
H. Tooling - Price and Availability
Refer paragraph 3.C and to Safran Service Bulletin J070000-25-07 or
J070000-25-08 or J070000-25-09 or J070000-25-10 for a list of special tools
and equipment for this service bulletin.

### Page 5

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 5 of 38
Jun 29/2023
I. Weight and Balance
For aircraft 7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696,
7698, 7699, 7701 thru 7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747
thru 7783, 7786 thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru
7861, 7863, 7865, 7867 thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949,
7951 thru 7957, 7959 thru 7972, 7974, 7976 thru 7980, 7982, 7983, 7985 thru 7988,
8000 thru 8007, 8009, 8011 thru 8042, 8044, 8045, 8047, 8050, 8059 and 8062
WEIGHT ARM MOMENT ¡
-1.1 lb +452.0 in. -0.497 (1000 lb‐in.)
-0.50 kg +11.48 m -0.0057 (1000 kg‐m)
¡ The value in the Moment column is divided by 1000.
Refer to Weight and Balance Manual.
For Aircraft 7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866,
7901, 7902, 7910, 7915, 7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010,
8058, 8061 and 8064
WEIGHT ARM MOMENT ¡
-1.1 lb +456.5 in. -0.502 (1000 lb‐in.)
-0.50 kg +11.60 m -0.0058 (1000 kg‐m)
¡ The value in the Moment column is divided by 1000.
Refer to Weight and Balance Manual.
For Aircraft 7676, 7686, 7784 and 7807
WEIGHT ARM MOMENT ¡
-1.1 lb +452.5 in. -0.498 (1000 lb‐in.)
-0.50 kg +11.49 m -0.0057 (1000 kg‐m)
¡ The value in the Moment column is divided by 1000.
Refer to Weight and Balance Manual.

### Page 6

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 6 of 38
Jun 29/2023
For Aircraft 8049
WEIGHT ARM MOMENT ¡
-1.2 lb +459.1 in. -0.551 (1000 lb‐in.)
-0.54 kg +11.66 m -0.0063 (1000 kg‐m)
¡ The value in the Moment column is divided by 1000.
Refer to Weight and Balance Manual.
For all aircraft
J. Electrical Load Data
Not changed.
K. References
Refer to the SB Introduction document for definition or explanation of service
bulletin content.
For MHIRJ reference only: Restriction and/or Special Instruction (RSI) C-A316,
Revision NC
Modification Summary 601R18705 Revision B
Safran Service Bulletin VSB J070000-25-07 , dated Apr/26/2023
Safran Service Bulletin VSB J070000-25-08, dated Apr/26/2023
Safran Service Bulletin VSB J070000-25-09, Revision 1,  dated Jun/07/2023
Safran Service Bulletin VSB J070000-25-10, dated Apr/26/2023
For MHIRJ reference only: PCA 7476
L. Other Publications Affected
Aircraft Maintenance Manual (AMM)
Aircraft Illustrated Parts Catalogue (AIPC)
Component Maintenance Manual (CMM)

### Page 7

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 7 of 38
Jun 29/2023
M. Relationship Chart
PRE‐SB
PART NUMBER NAME POST ‐SBPART NUMBER
3861151-501 Overhead Bin Support Assembly KCM601R41057-1
3861151-503 Overhead Bin Support Assembly KCM601R41057-3
3861151-505 Overhead Bin Support Assembly KCM601R41057-5
3861151-507 Overhead Bin Support Assembly KCM601R41058-7
3861151-509 Overhead Bin Support Assembly KCM601R41057-9
3861151-511 Overhead Bin Support Assembly KCM601R41057-11
3861151-513 Overhead Bin Support Assembly KCM601R41057-13
3861151-515 Overhead Bin Support Assembly KCM601R41057-15
3861151-517 Overhead Bin Support Assembly KCM601R41058-17
C671151-503 Overhead Bin Support Assembly KCM601R41060-3
C671151-505 Overhead Bin Support Assembly KCM601R41060-5
C671151-507 Overhead Bin Support Assembly KCM601R41060-7
C671151-509 Overhead Bin Support Assembly KCM601R41060-9
C671151-511 Overhead Bin Support Assembly KCM601R41060-11
C671151-513 Overhead Bin Support Assembly KCM601R41060-13

### Page 8

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 8 of 38
Jun 29/2023
2. ACCOMPLISHMENT INSTRUCTIONS
Reference Information
REFERENCE DESIGNATION
AMM 20-21-00-910-801 Torquing - Maintenance Practices
AMM 20-60-13-930-801 Identification of Aircraft Parts and Assemblies
AMM 25-23-01-000-802 Removal of the Overhead Storage
Compartment (North American Configuration)
AMM 25-23-01-000-804 Removal of the Overhead Storage
Compartment (European Configuration)
AMM 25-23-01-000-805 Removal of the Overhead Storage
Compartment (North American Configuration)
AMM 25-23-01-000-806 Removal of the Overhead Storage
Compartment (European Configuration)
AMM 25-23-01-400-805 Installation of the Overhead Storage
Compartment (North American Configuration
AMM 25-23-01-400-806 Installation of the Overhead Storage
Compartment (European Configuration)
SRM 51-21-11 Corrosion Prevention Procedures
SRM 51-21-16 Finish Codes
SRM 51-26-00 Cleaning
SRM 51-40-11 Preparation of Fasteners Holes
Tolerance Information
LINEAR TOLERANCES ANGULAR TOLERANCE
X.XX in. (X.X mm) X.X in. (X mm)
±0° 30”±0.03 in. ±0.1 in.
±0.8 mm ±3 mm
NOTE: The tolerances above apply to the dimensions given in this service
bulletin, except when specified differently.

### Page 9

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 9 of 38
Jun 29/2023
A. Job Set‐Up
NOTE: The steps in the Job Set‐Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Open the passenger door.
B. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft or if damage is found, speak with a
representative of MHIRJ in the CRC at 450-990-7CRC (450-990-7272)
direct, 1-833-990-7CRC (1-833-990-7272) toll free for North America or
+1-450-990-7CRC (+1-450-990-7272) for international callers or e‐mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
Refer to Figure 1.
(2) Remove the overhead bins as follows:
(a) Temporarily identify the left and right overhead bins and their location in
the aircraft as shown on Figure 1.
NOTE: It is important to respect the identification method (from 1R to 5R
and from 1L to 5L) as shown in the Figure 1 to make sure the
overhead bins are installed at the same location.
(b) Remove the left overhead bins (1L), (2L), (3L), (4L) and (5L) (refer to
AMM 25-23-01-000-802, AMM 25-23-01-000-804).
(c) Remove the right overhead bins (1R), (2R), (3R), (4R) and (5R) (refer to
AMM 25-23-01-000-802, AMM 25-23-01-000-804).

### Page 10

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 10 of 38
Jun 29/2023
For aircraft 7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696,
7698, 7699, 7701 thru 7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747
thru 7783, 7786 thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru
7861, 7863, 7865, 7867 thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949,
7951 thru 7957, 7959 thru 7972, 7974, 7976 thru 7980, 7982, 7983, 7985 thru 7988,
8000 thru 8007, 8009, 8011 thru 8042, 8044, 8045, 8047, 8050, 8059 and 8062
NOTE: Shear pin assemblies, screws and tools (drill bushing and double margin
step drill) are parts of kits from Safran service bulletin. They will be used
to complete the installation of the overhead bins.
(3) Do the Safran service bulletin J070000-25-07 on the left overhead bins (1L),
(2L), (3L), (4L), (5L) and their support assemblies (6L), (7L), (8L), (9L) and
(10L).
(4) Do the Safran service bulletin J070000-25-07 on the right overhead bins
(1R), (2R), (3R), (4R), (5R) and their support assemblies (6R), (7R), (8R), (9R)
and (10R).
For Aircraft 7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866,
7901, 7902, 7910, 7915, 7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010,
8058, 8061 and 8064
NOTE: Shear pin assemblies, screws and tools (drill bushing and double margin
step drill) are parts of kits from Safran service bulletin. They will be used
to complete the installation of the overhead bins.
(5) Do the Safran service bulletin J070000-25-09 on the left overhead bins (1L),
(2L), (3L), (4L), (5L) and their support assemblies (6L), (7L), (8L), (9L) and
(10L).
(6) Do the Safran service bulletin J070000-25-09 on the right overhead bins
(1R), (2R), (3R), (4R), (5R) and their support assemblies (6R), (7R), (8R), (9R)
and (10R).
For Aircraft 7676, 7686, 7784 and 7807
NOTE: Shear pin assemblies, screws and tools (drill bushing and double margin
step drill) are parts of kits from Safran service bulletin. They will be used
to complete the installation of the overhead bins.
(7) Do the Safran service bulletin J070000-25-08 on the left overhead bins (1L),
(2L), (3L), (4L), (5L) and their support assemblies (6L), (7L), (8L), (9L) and
(10L).
(8) Do the Safran service bulletin J070000-25-08 on the right overhead bins
(1R), (2R), (3R), (4R), (5R) and their support assemblies (6R), (7R), (8R), (9R)
and (10R).

### Page 11

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 11 of 38
Jun 29/2023
For Aircraft 8049
NOTE: Shear pin assemblies, screws and tools (drill bushing and double margin
step drill) are parts of kits from Safran service bulletin. They will be used
to complete the installation of the overhead bins.
(9) Do the Safran service bulletin J070000-25-10 on the left overhead bins (1L),
(2L), (3L), (4L), (5L) and their support assemblies (6L), (7L), (8L), (9L) and
(10L).
(10) Do the Safran service bulletin J070000-25-10 on the right overhead bins
(1R), (2R), (3R), (4R), (5R) and their support assemblies (6R), (7R), (8R), (9R)
and (10R).
For all aircraft
(11) Make sure that all support tubes from the left overhead bin support assembly
(6L), (7L), (8L), (9L) and (10L) have no serrations.
(12) Make sure that all support tubes from the right overhead bin support
assembly (6R), (7R), (8R), (9R) and (10R) have no serrations.
(13) Install the left and right overhead bins as follows:
(a) Temporarily install the left overhead bins (1L), (2L), (3L), (4L) and (5L) at
the correct location as follows:
CAUTION: IT IS IMPORTANT TO CORRECTLY LOCATE ALL THE OVERHEAD
BINS BEFORE DRILLING THE OUTBOARD TUBES FOR THE
SHEAR PIN HOLES. IF THE SHEAR PIN HOLE IN THE OUTBOARD
TUBE IS NOT CORRECTLY LOCATED, THE OUTBOARD TUBE
MUST BE REPLACED. IT IS NOT PERMITTED TO DRILL A SECOND
HOLE OR DRILL AN OVAL HOLE.
1 Temporarily install the left overhead bins (1L), (2L), (3L), (4L) and
(5L) (refer to AMM 25-23-01-400-805 and AMM
25-23-01-400-806).
NOTE: Use the AMM tasks even if the shear pins are not installed
yet.
NOTE: Do not do the steps for the following items:
−  Air conditioning ducts.
−  Electrical connectors and bonding-jumpers.
−  Thermal insulation blanket.
−  Trim strips, covers between overhead bins and end filler.
−  Overhead bin door adjustment.
−  Close Out section.

### Page 12

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 12 of 38
Jun 29/2023
2 Make sure that all the distances between the left overhead bins
(1L), (2L), (3L), (4L) and (5L) are approximately 0.25 in (6.4 mm) as
shown in Figure 1, view A-A.
(b) Temporarily install the right overhead bins (1R), (2R), (3R), (4R) and (5R)
at the correct location as follows:
CAUTION: IT IS IMPORTANT TO CORRECTLY LOCATE ALL THE OVERHEAD
BINS BEFORE DRILLING THE OUTBOARD TUBES FOR THE
SHEAR PIN HOLES. IF THE SHEAR PIN HOLE IN THE OUTBOARD
TUBE IS NOT CORRECTLY LOCATED, THE OUTBOARD TUBE
MUST BE REPLACED. IT IS NOT PERMITTED TO DRILL A SECOND
HOLE OR DRILL AN OVAL HOLE.
1 Temporarily install the right overhead bins (1R), (2R), (3R), (4R)
and (5R) (refer to AMM 25-23-01-400-805 and AMM
25-23-01-400-806).
NOTE: Use the AMM tasks even if the shear pins are not installed
yet.
NOTE: Do not do the steps for the following items:
−  Air conditioning ducts.
−  Electrical connectors and bonding-jumpers.
−  Thermal insulation blanket.
−  Trim strips, covers between overhead bins and end filler.
−  Overhead bin door adjustment.
−  Close Out section.
2 Make sure that all the distances between the right overhead bins
(1R), (2R), (3R), (4R) and (5R) are approximately 0.25 in (6.4 mm)
as shown in Figure 1, view A-A.
Refer to Figure 1, Sheet 12 and Figure 2.
(14) Drill the hole for the shear pin (3) in the left overhead bin support assemblies
(6L), (7L), (8L), (9L) and (10L) as follows:
(a) On a 5/32 in. (0.1563 in.) (3.970 mm) drill bit, install a drill stop at 
1.750 in (44.5 mm) from the tip of the drill bit.
NOTE: It is important to install the drill stop to prevent damage on the
components behind the overhead bins.

### Page 13

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 13 of 38
Jun 29/2023
Refer to Figure 2.
(b) Install the drill bushing (15) on the upper hook as follows:
1 Find the location of the aft hook in the overhead bin.
2 Open the lower hook to its fully open position to have access to the
upper hook.
3 Locate the hole with a diameter of 0.315 to 0.322 in. (8.00 to 8.18
mm) on the upper hook.
4 Make sure you clearly see the outboard tube through the hole of
the upper hook.
5 Install the drill bushing (15) on the upper hook.
6 Make sure that the drill bushing (15) is flat against the upper hook.
7 Hold the bushing (15) in position
NOTE: It is recommended to use a bushing handle or an equivalent.
(c) With the 5/32 in. (0.1563 in.) (3.970 mm) drill bit and the drill bushing
(15), drill a pilot hole through the inboard and outboard walls of the
overhead bin support assemblies (refer to SRM 51-40-11) that follow:
NOTE: If necessary, use lubricant (Boelube or equivalent).
−  The left overhead bin support assembly (6L).
−  The left overhead bin support assembly (7L).
−  The left overhead bin support assembly (8L).
−  The left overhead bin support assembly (9L).
−  The left overhead bin support assembly (10L).
(d) Remove the left overhead bins (1L), (2L), (3L), (4L) and (5L) (refer to
AMM 25-23-01-000-805, AMM 25-23-01-000-806).
(e) On the double margins step drill (16), install a drill stop (or an
equivalent) at 2.85 in (72.4 mm) from the tip of the double margin step
drill.
NOTE: It is important to install the drill stop (or an equivalent) to have the
proper hole diameter in the tube walls as shown in Figure 2.

### Page 14

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 14 of 38
Jun 29/2023
(f) Open the 5/32 in. (0.1563 in.) (3.970 mm) pilot hole on the overhead bin
support assemblies (6L), (7L), (8L), (9L) and (10L) to the final dimension
of the shear pin as follows:
1 Engage the pilot section of the double margins step drill (16) in the
two 5/32 in. (0.1563 in.) (3.970 mm) pilot holes of the outboard
tube of the overhead bin support assembly (6L).
2 Make sure that the pilot section of the double margin step drill
goes through the outboard tube (from one wall to the other).
3 Carefully open the 5/32 in. (0.1563 in.) (3.970 mm) pilot hole on the
inboard and outboard walls of the outboard tube to 0.198 to 0.204
in. (5.03 to 5.18 mm) as shown on Figure 2 (refer to SRM
51-40-11).
NOTE: 0.198 to 204 in. (5.03 to 5.18 mm) is the center section of the
double-margin step-drill.
NOTE: If necessary, use lubricant (Boelube or equivalent).
4 Carefully open the 0.198 to 0.204 in. (5.03 to 5.18 mm) hole on the
inboard wall of the outboard tube to 0.311 to 0.318 in. (7.90 to 8.08
mm) as shown on Figure 2 (refer to SRM 51-40-11).
NOTE: 0.311 to 0.318 in. (7.90 to 8.08 mm) is the larger section of
the double-margin step-drill.
NOTE: If necessary, use lubricant (Boelube or equivalent).
5 Make sure to only open the inboard wall of the outboard tube to
0.311 to 0.318 in. (7.90 to 8.08 mm) as shown on Figure 2.
6 Do the steps above for the outboard tube of the overhead bin
support assemblies (7L), (8L), (9L) and (10L).
(g) Carefully remove the burrs and the sharp edges from the shear pin holes
on the outboard tube of the left overhead bin support assemblies (6L),
(7L), (8L), (9L) and (10L) (refer to SRM 51-26-00).
(h) Clean the shear pin hole area and the outer surface of the outboard tube
of the overhead bin support assemblies (6L), (7L), (8L), (9L) and (10L)
(refer to SRM 51-26-00).
(i) Remove the chips and clean the inner walls of the overhead bin support
assemblies (6L), (7L), (8L), (9L) and (10L) (refer to SRM 51-26-00).
(j) Apply a conversion coating (MIL-DTL-81706 class 1A) on the bare
surface of the two shear pin holes on the overhead bin support
assemblies (6L), (7L), (8L), (9L) and (10L) (refer to SRM 51-21-11 and
SRM 51-21-16).

### Page 15

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 15 of 38
Jun 29/2023
Refer to Figure 1, Sheet 12 and Figure 2.
(15) Drill the hole for the shear pin (3) in the right overhead bin support assemblies
(6R), (7R), (8R), (9R) and (10R) as follows:
(a) On a 5/32 in. (0.1563 in.) (3.970 mm) drill bit, install a drill stop at 
1.750 in (44.5 mm) from the tip of the drill bit.
NOTE: It is important to install the drill stop to prevent damage on the
components behind the overhead bins.
Refer to Figure 2.
(b) Install the drill bushing (15) on the upper hook as follows:
1 Find the location of the aft hook in the overhead bin.
2 Open the lower hook to its fully open position to have access to the
upper hook.
3 Locate the hole with a diameter of 0.315 to 0.322 in. (8.00 to 8.18
mm) on the upper hook.
4 Make sure you clearly see the outboard tube through the hole of
the upper hook.
5 Install the drill bushing (15) on the upper hook.
6 Make sure that the drill bushing (15) is flat against the upper hook.
7 Hold the bushing (15) in position
NOTE: It is recommended to use a bushing handle or an equivalent.
(c) With the 5/32 in. (0.1563 in.) (3.970 mm) drill bit and the drill bushing
(15), drill a pilot hole through the inboard and outboard walls of the
overhead bin support assemblies (refer to SRM 51-40-11) that follow:
NOTE: If necessary, use lubricant (Boelube or equivalent).
−  The right overhead bin support assembly (6R).
−  The right overhead bin support assembly (7R).
−  The right overhead bin support assembly (8R).

### Page 16

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 16 of 38
Jun 29/2023
−  The right overhead bin support assembly (9R).
−  The right overhead bin support assembly (10R).
(d) Remove the right overhead bins (1R), (2R), (3R), (4R) and (5R) (refer to
AMM 25-23-01-000-805, AMM 25-23-01-000-806).
(e) On the double margins step drill (16), install a drill stop (or an
equivalent) at 2.85 in (72.4 mm) from the tip of the double margin step
drill.
NOTE: It is important to install the drill stop (or an equivalent) to have the
proper hole diameter in the tube walls as shown in Figure 2.
(f) Open the 5/32 in. (0.1563 in.) (3.970 mm) pilot hole on the overhead bin
support tube assemblies (6R), (7R), (8R), (9R) and (10R) to the final
dimension of the shear pin as follows:
1 Engage the pilot section of the double margins step drill (16) in the
two 5/32 in. (0.1563 in.) (3.970 mm) pilot holes of the outboard
tube of the overhead bin support assembly (6R).
2 Make sure that the pilot section of the double-margin step-drill
goes through the outboard tube (from one wall to the other).
3 Carefully open the 5/32 in. (0.1563 in.) (3.970 mm) pilot hole on the
inboard and outboard walls of the outboard tube to 0.198 to 0.204
in. (5.03 to 5.18 mm) as shown on Figure 2 (refer to SRM
51-40-11).
NOTE: 0.198 to 0.204 in. (5.03 to 5.18 mm) is the center section of
the double-margin step-drill.
NOTE: If necessary, use lubricant (Boelube or equivalent).
4 Carefully open the 0.198 to 0.204 in. (5.03 to 5.18 mm) hole on the
inboard wall of the outboard tube to 0.311 to 0.318 in. (7.90 to 8.08
mm) as shown on Figure 2 (refer to SRM 51-40-11).
NOTE: 0.311 to 0.318 in. (7.90 to 8.08 mm) is the larger section of
the double-margin step-drill.
NOTE: If necessary, use lubricant (Boelube or equivalent).

### Page 17

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 17 of 38
Jun 29/2023
5 Make sure to only open the inboard wall of the outboard tube to
0.311 to 0.318 in. (7.90 to 8.08 mm) as shown on Figure 2.
6 Do the steps above for the outboard tube of the overhead bin
support assemblies (7R), (8R), (9R) and (10R).
(g) Carefully remove the burrs and the sharp edges from the shear pin holes
on the outboard tube of the right overhead bin support assemblies (6R),
(7R), (8R), (9R) and (10R) (refer to SRM 51-26-00).
(h) Clean the shear pin hole area and the outer surface of the outboard tube
of the overhead bin support assemblies (6R), (7R), (8R), (9R) and (10R)
(refer to SRM 51-26-00).
(i) Remove the chips and clean the inner walls of the overhead bin support
assemblies (6R), (7R), (8R), (9R) and (10R) (refer to SRM 51-26-00).
(j) Apply a conversion coating (MIL-DTL-81706 class 1A) on the bare
surface of the two shear pin holes on the overhead bin support
assemblies (6R), (7R), (8R), (9R) and (10R) (refer to SRM 51-21-11
and SRM 51-21-16).
For Aircraft 7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696,
7698, 7699, 7701 thru 7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747
thru 7783, 7786 thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru
7861, 7863, 7865, 7867 thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949,
7951 thru 7957, 7959 thru 7972, 7974, 7976 thru 7980, 7982, 7983, 7985 thru 7988,
8000 thru 8007, 8009, 8011 thru 8042, 8044, 8045, 8047, 8050, 8059 and 8062
Refer to Figure 1, sheet 3.
(16) Identify the left overhead bin support assemblies (6L), (7L), (8L), (9L) and
(10L) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6L) on the outboard tube as
KCM601R41057-9 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7L) on the outboard tube as
KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8L) on the outboard tube as
KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9L) on the outboard tube as
KCM601R41057-5 (refer to AMM 20-60-13-930-801).

### Page 18

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 18 of 38
Jun 29/2023
(e) Identify the overhead bin support assembly (10L) on the outboard tube
as KCM601R41057-13 (refer to AMM 20-60-13-930-801).
(17) Identify the right overhead bin support assemblies (6R), (7R), (8R), (9R) and
(10R) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6R) on the outboard tube
as KCM601R41057-11 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7R) on the outboard tube
as KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8R) on the outboard tube
as KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9R) on the outboard tube
as KCM601R41057-5 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10R) on the outboard tube
as KCM601R41057-15 (refer to AMM 20-60-13-930-801).
For Aircraft 7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866,
7901, 7902, 7910, 7915, 7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010,
8058, 8061 and 8064
Refer to Figure 1, sheet 5.
(18) Identify the left overhead bin support assemblies (6L), (7L), (8L), (9L) and
(10L) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6L) on the outboard tube as
KCM601R41057-9 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7L) on the outboard tube as
KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8L) on the outboard tube as
KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9L) on the outboard tube as
KCM601R41057-5 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10L) on the outboard tube
as KCM601R41058-17 (refer to AMM 20-60-13-930-801).

### Page 19

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 19 of 38
Jun 29/2023
(19) Identify the right overhead bin support assemblies (6R), (7R), (8R), (9R) and
(10R) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6R) on the outboard tube
as KCM601R41058-7 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7R) on the outboard tube
as KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8R) on the outboard tube
as KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9R) on the outboard tube
as KCM601R41057-5 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10R) on the outboard tube
as KCM601R41058-17 (refer to AMM 20-60-13-930-801).
For Aircraft 7676, 7686, 7784 and 7807
Refer to Figure 1, sheet 7.
(20) Identify the left overhead bin support assemblies (6L), (7L), (8L), (9L) and
(10L) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6L) on the outboard tube as
KCM601R41057-9 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7L) on the outboard tube as
KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8L) on the outboard tube as
KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9L) on the outboard tube as
KCM601R41057-5 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10L) on the outboard tube
as KCM601R41058-17 (refer to AMM 20-60-13-930-801).

### Page 20

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 20 of 38
Jun 29/2023
(21) Identify the right overhead bin support assemblies (6R), (7R), (8R), (9R) and
(10R) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6R) on the outboard tube
as KCM601R41057-11 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7R) on the outboard tube
as KCM601R41057-3 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8R) on the outboard tube
as KCM601R41057-1 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9R) on the outboard tube
as KCM601R41057-5 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10R) on the outboard tube
as KCM601R41057-15 (refer to AMM 20-60-13-930-801).
For Aircraft 8049
Refer to Figure 1, sheet 9.
(22) Identify the left overhead bin support assemblies (6L), (7L), (8L), (9L) and
(10L) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6L) on the outboard tube as
KCM601R41060-3 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7L) on the outboard tube as
KCM601R41060-5 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8L) on the outboard tube as
KCM601R41060-7 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9L) on the outboard tube as
KCM601R41060-9 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10L) on the outboard tube
as KCM601R41060-13 (refer to AMM 20-60-13-930-801).

### Page 21

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 21 of 38
Jun 29/2023
(23) Identify the right overhead bin support assemblies (6R), (7R), (8R), (9R) and
(10R) on the outboard tubes as follows:
(a) Identify the overhead bin support assembly (6R) on the outboard tube
as KCM601R41060-3 (refer to AMM 20-60-13-930-801).
(b) Identify the overhead bin support assembly (7R) on the outboard tube
as KCM601R41060-5 (refer to AMM 20-60-13-930-801).
(c) Identify the overhead bin support assembly (8R) on the outboard tube
as KCM601R41060-7 (refer to AMM 20-60-13-930-801).
(d) Identify the overhead bin support assembly (9R) on the outboard tube
as KCM601R41060-9 (refer to AMM 20-60-13-930-801).
(e) Identify the overhead bin support assembly (10R) on the outboard tube
as KCM601R41060-11 (refer to AMM 20-60-13-930-801).
For all aircraft
Refer to Figure 1, sheet 12.
(24) Install the shear pin (3) on the left overhead bin (1L), (2L), (3L), (4L) and (5L)
lower hook as follows:
(a) On the shear pin (3), press the two spring loaded pins.
(b) Put the two spring loaded pins in line with the slits on the lower hook.
(c) Release the two spring loaded pins.
(d) Make sure that the two spring loaded pins are engaged in the slits of the
lower hook.
(e) Make sure that the shear pin (3) can move freely up and down in the slits
of the lower hook.

### Page 22

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 22 of 38
Jun 29/2023
(25) Install the shear pin (3) on the right overhead bin (1R), (2R), (3R), (4R) and
(5R) lower hook as follows:
NOTE: For aircraft 8049, the overhead bin (4R) is installed with the shear pin (5)
instead of shear pin (3).
(a) On the shear pin (3), press the two spring loaded pins.
(b) Put the two spring loaded pins in line with the slits on the lower hook.
(c) Release the two spring loaded pins.
(d) Make sure that the two spring loaded pins are engaged in the slits of the
lower hook.
(e) Make sure that the shear pin (3) can move freely up and down in the slits
of the lower hook.
(26) Install the left overhead bins (1L), (2L), (3L), (4L) and (5L) (refer to AMM
25-23-01-400-805 and AMM 25-23-01-400-806).
NOTE: Torque value for screw (4) on lower hook is 20.0-25.0 lb.in 
(2.3 -2.8 Nm) (refer to AMM 20-21-00-910-801).
(27) Install the right overhead bins (1R), (2R), (3R), (4R) and (5R) (refer to AMM
25-23-01-400-805 and AMM 25-23-01-400-806).
NOTE: Torque value for screw (4) on lower hook is 20.0-25.0 lb.in 
(2.3 -2.8 Nm) (refer to AMM 20-21-00-910-801).

### Page 23

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 23 of 38
Jun 29/2023
C. Job Close‐Out
NOTE: The steps in the Job Close‐Out section of this service bulletin, except for
the return‐to‐service tests, are recommended steps. The steps give a
recommendation to install components removed during the Job Set‐Up.
This recommendation is to make sure that the aircraft is safe and ready
to return to service. Alternative steps can be used at the operator
discretion.
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Close the passenger door.
(3) When this service bulletin is completed, add the weight and balance data
shown in paragraph 1.I. of this service bulletin to the Weight and Balance
Manual. Under `Description of Change' enter “Service Bulletin 601R-25-206,
incorporated.”
(4) When this service bulletin is completed, make this entry in the applicable
logbooks: “Service Bulletin 601R-25-206, Equipment / Furnishings -
Storage Compartment - Replacement of Overhead Bins Serrated Hooks and
Support Tubes and Installation of a Shear Pin, incorporated.”

### Page 24

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 24 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 1 of 12)
rsb601r25206_007.cgm, gd, gb, may17/2023
B
FS350.50
1R
FS405.00
2R
7R
FS409.00
+86.00 FS457.00
3R 8R 4R 9R
FS547.00
5R
FS559.00
+48.00
10R
RBL21.79
BL0.00
LBL21.79
10L
FS559.00
+80.50
5L9L4L8L3LC7L2L1L6L
RBL29.31
LBL29.31
6R
A A
A
TYIPCAL (4 PLACES)
RIGHT SIDE SHOWN
LEFT SIDE OPPOSITE
OUTBOARD TUBE ASSEMBLY
NOT SHOWN FOR CLARITY
OF BIN JOINT
BIN ASSY
(REF)
CL
FS405.00
FS409.00 +86.00
FS457.00
FS547.00
BIN ASSY
(REF)
0.25 in.
(6.4 mm)
- A
B
OVERHEAD BIN LAYOUT
EFFECTIVITY:
7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696, 7698, 7699, 7701 thru
7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747 thru 7783, 7786
thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru 7861, 7863, 7865, 7867
thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949, 7951 thru 7957, 7959 thru 7972,
7974, 7976 thru 7980, 7982, 7983,7985 thru 7988, 8000 thru 8007, 8009, 8011 thru
8042, 8044, 8045, 8047, 8050, 8059 and 8062.
NOTE
For legend refer to next pages.

### Page 25

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 25 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 2 of 12)
rsb601r25206_008.cgm, gd, gb, may17/2023
LEGEND FOR ITEMS 1L TO 5L AND 1R TO 5R BIN ASSENBLIES
BIN ASSY
LOCATION PART NUMBER
3862016C523
1L
3862016N523
3862016N547
3862016Z547
3862016AK555
3862017AK501
3862017BB525
3862017BF527
3862016C507
3862016N507
3862016Z507
3862016AK507
3862017AK507
3862017BB507
3862017BF507
3862016C511
3862016N511
3862016Z511
3862016AK511
3862017AK511
3862017BB511
3862017BF511
3862016C515
3862016N515
3862016Z515
3862016AK515
3862017AK515
3862017BB515
3862017BF515
3862016C527
3862016N527
3862016Z527
3862016AK527
3862017AK519
3862017BB523
3862017BF529
2L
3L
4L
5L
BIN ASSY
LOCATION PART NUMBER
3862016C525
1R
3862016N525
3862016Z525
3862016AK525
3862016AK565
3862017AK503
3862017BB521
3862017BF521
3862016C509
3862016N509
3862016Z509
3862016AK509
3862017AK509
3862017BB509
3862017BF509
3862016C513
3862016N513
3862016Z513
3862016AK513
3862017AK513
3862017BB513
3862017BF513
3862016C517
3862016N517
3862016Z517
3862016AK517
3862017AK517
3862017BB517
3862017BF517
3862016N561
3862016C563
3862016N563
3862016Z563
3862016AK563
3862017AK505
3862017BB505
2R
3R
4R
5R
3862017BF505EFFECTIVITY:
7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696, 7698, 7699, 7701 thru
7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747 thru 7783, 7786
thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru 7861, 7863, 7865, 7867
thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949, 7951 thru 7957, 7959 thru 7972,
7974, 7976 thru 7980, 7982, 7983,7985 thru 7988, 8000 thru 8007, 8009, 8011 thru
8042, 8044, 8045, 8047, 8050, 8059 and 8062.

### Page 26

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 26 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 3 of 12)
rsb601r25206_009.cgm, gd, gb, may17/2023
LEGEND FOR ITEMS 6L TO 10L AND 6R TO 10R
OVERHEAD BIN SUPPORT ASSEMBLIES
BIN SUPPORT
ASSY
LOCATION
PRE-MOD
PART NUMBER
POST-MOD
PART NUMBER
6L
7L
8L
9L
10L
6R
7R
8R
9R
10R
KCM601R41057-9
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41057-13
KCM601R41057-11
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41057-15
3861151-509
3861151-503
3861151-501
3861151-505
3861151-513
3861151-511
3861151-503
3861151-501
3861151-505
3861151-515
EFFECTIVITY:
7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696, 7698, 7699, 7701 thru
7703, 7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747 thru 7783, 7786
thru 7788, 7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru 7861, 7863, 7865, 7867
thru 7900, 7903 thru 7909, 7911 thru 7914, 7916 thru 7949, 7951 thru 7957, 7959 thru 7972,
7974, 7976 thru 7980, 7982, 7983,7985 thru 7988, 8000 thru 8007, 8009, 8011 thru
8042, 8044, 8045, 8047, 8050, 8059 and 8062.

### Page 27

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 27 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 4 of 12)
B
A
rsb601r25206_001.cgm, gd, gb, may9/2023
TYIPCAL (4 PLACES)
RIGHT SIDE SHOWN
LEFT SIDE OPPOSITE
OUTBOARD TUBE ASSEMBLY
NOT SHOWN FOR CLARITY
OF BIN JOINT
BIN ASSY
(REF)
CL
FS405.00
FS409.00 +86.00
FS457.00
FS547.00
BIN ASSY
(REF)
0.25 in.
(6.4 mm)
-
RBL21.79
BL0.00
LBL21.79
10R
FS559.00
+84.00
5R
FS547.00
9R4R
FS457.00
3R 8R
FS409.00
+86.00
7R
2R
FS405.00
FS380.00
1R
6R
FS349.75
6L 1L 2L 7L
C 3L 8L 4L 9L 5L 10L
OVERHEAD BIN LAYOUT
A
A A
EFFECTIVITY:
7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866, 7901, 7902, 7910, 7915,
7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010, 8058, 8061 and 8064.
B
RBL29.31
LBL29.31
NOTE
For legend refer to next page.

### Page 28

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 28 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 5 of 12)
BIN SUPPORT
ASSY
LOCATION
PRE-MOD
PART NUMBER
POST-MOD
PART NUMBER
6L
7L
8L
9L
10L
6R
7R
8R
9R
10R
3861151-509
3861151-503
3861151-501
3861151-505
3861151-517
3861151-507
3861151-503
3861151-501
3861151-505
3861151-517
KCM601R41057-9
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41058-17
KCM601R41058-7
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41058-17
LEGEND FOR ITEMS 6L TO 10L AND 6R TO 10R
OVERHEAD BIN SUPPORT ASSEMBLIES
rsb601r25206_002.cgm, gd, gb, may17/2023
EFFECTIVITY:
7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866, 7901, 7902, 7910, 7915,
7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010, 8058, 8061 and 8064.
LEGEND FOR ITEMS 1L TO 5L AND 1R TO 5R BIN ASSEMBLIES
3862016-539
3862016B539
3862016N539
3862016N559
3862016-507
3862016B507
3862016N507
3862016-511
3862016B511
3862016N511
3862016-515
3862016B515
3862016N515
3862016B519
3862016N519
3862016-535
3862016N535
3862016N545
1L
2L
3L
4L
5L
BIN ASSY
LOCATION PART NUMBER
3862016-505
3862016B505
3862016N505
3862016-509
3862016B509
3862016N509
3862016-513
3862016B513
3862016N513
3862016-517
3862016B517
3862016N517
3862016B521
3862016-537
3862016N537
BIN ASSY
LOCATION PART NUMBER
1R
2R
3R
4R
5R

### Page 29

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 29 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 6 of 12)
A
rsb601r25206_010.cgm, gd, gb, may17/2023
TYIPCAL (4 PLACES)
RIGHT SIDE SHOWN
LEFT SIDE OPPOSITE
OUTBOARD TUBE ASSEMBLY
NOT SHOWN FOR CLARITY
OF BIN JOINT
BIN ASSY
(REF)
CL
FS405.00
FS409.00 +86.00
FS457.00
FS547.00
BIN ASSY
(REF)
0.25 in.
(6.4 mm)
- A
FS349.75
1R
6R
FS559.00
+51.50FS547.00FS457.00FS409.00+86.00FS405.00
2R 7R 3R 8R 4R 9R 5R 10R
10L
RBL21.79
BL0.00
LBL21.79
RBL29.31
LBL29.31
A A
C FS559.00
+84.00
6L 1L 2L 7L 3L 8L 4L 9L 5L
B
B
OVERHEAD BIN LAYOUT
7676, 7686, 7784 and 7807.
NOTE
For legend refer to next page.
EFFECTIVITY:

### Page 30

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 30 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 7 of 12)
rsb601r25206_011.cgm, gd, gb, may17/2023
LEGEND FOR ITEMS 1L TO 5L AND
1R TO 5R BIN ASSEMBLIES
3862016N547
3862016N507
3862016N511
3862016N515
3862016N535
3862016N525
3862016N509
3862016N513
3862016N517
3862016N549
1L
2L
3L
4L
5L
BIN ASSY
LOCATION PART NUMBER
1R
2R
3R
4R
5R
LEGEND FOR ITEMS 6L TO 10L AND 6R TO 10R
OVERHEAD BIN SUPPORT ASSEMBLIES
BIN SUPPORT
ASSY
LOCATION
PRE-MOD
PART NUMBER
POST-MOD
PART NUMBER
6L
7L
8L
9L
10L
6R
7R
8R
9R
10R
3861151-509
3861151-503
3861151-501
3861151-505
3861151-517
3861151-511
3861151-503
3861151-501
3861151-505
3861151-515
KCM601R41057-9
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41058-17
KCM601R41057-11
KCM601R41057-3
KCM601R41057-1
KCM601R41057-5
KCM601R41057-15
EFFECTIVITY:
7676, 7686, 7784 and 7807.

### Page 31

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 31 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 8 of 12)
rsb601r25206_012.cgm, gd, gb, may9/2023
OF BIN JOINT
BIN ASSY
(REF)
CL
FS409.00 +22.00
FS466.48
FS547.84
BIN ASSY
(REF)
0.25 in.
(6.4 mm)
B
FS353.00
1R
FS559.00
+32.00FS547.84FS466.48
FS409.00
+100.00
2R 7R 3R 8R 4R 9R 5R 10R6R
FS409.00
+22.00
FS409.00
+104.00
RBL21.79
BL0.00
LBL21.79
RBL29.31
LBL29.31
10L
FS559.00
+64.50
6L1L 2L 7L 3L 8L 4L 9L 5L
A A
C
B
OVERHEAD BIN LAYOUT
A
TYIPCAL (3 PLACES)
RIGHT SIDE SHOWN
LEFT SIDE OPPOSITE
OUTBOARD TUBE ASSEMBLY
NOT SHOWN FOR CLARITY
- A
NOTE
For legend refer to next page.
EFFECTIVITY:
8049.

### Page 32

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 32 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 9 of 12)
rsb601r25206_013.cgm, gd, gb, may17/2023
LEGEND FOR ITEMS 1L TO 5L AND
1R TO 5R BIN ASSEMBLIES
LEGEND FOR ITEMS 6L TO 10L AND 6R TO 10R
OVERHEAD BIN SUPPORT ASSEMBLIES
BIN SUPPORT
ASSY
LOCATION
PRE-MOD
PART NUMBER
POST-MOD
PART NUMBER
6L
7L
8L
9L
10L
6R
7R
8R
9R
10R
C671151-503
C671151-505
C671151-507
C671151-509
C671151-513
C671151-503
C671151-505
C671151-507
C671151-509
C671151-511
KCM601R41060-3
KCM601R41060-5
KCM601R41060-7
KCM601R41060-9
KCM601R41060-13
KCM601R41060-3
KCM601R41060-5
KCM601R41060-7
KCM601R41060-9
KCM601R41060-11
C673101CX101
C673102CX101
C673103CX101
C673104CX101
C673105CX101
C673101CX102
C673102CX102
C673151CX102
C673152CX102
C673153CX102
1L
2L
3L
4L
5L
BIN ASSY
LOCATION PART NUMBER
1R
2R
3R
4R
5R
EFFECTIVITY:
8049.

### Page 33

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 33 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 10 of 12)
LEGEND
11. Hook assy with serrations.
12. Outboard tube assy
      (with serrations).
rsb601r25206_003.cgm, gd, gb, may17/2023
LBL
29.31
DC
PRE-MOD
OVERHEAD BIN SHOWN (TYPICAL)
LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE
VIEW LOOKING DOWN
All aircraft.
7673 thru 7675, 7677 thru 7683, 7685, 7687 thru 7689, 7691 thru 7696, 7698, 7699, 7701 thru 7703,
7707 thru 7731, 7733 thru 7737, 7739 thru 7745, 7747 thru 7783, 7786 thru 7788,
7790 thru 7806, 7808 thru 7845, 7847 thru 7850, 7852 thru 7861, 7863, 7865, 7867 thru 7900,
7903 thru 7909, 7911 thru 7914, 7916 thru 7949, 7951 thru 7957, 7959 thru 7972, 7974,
7976 thru 7980, 7982, 7983, 7985 thru 7988, 8000 thru 8004, 8006, 8007, 8009, 8011 thru 8042,
8044, 8045, 8047, 8050 and 8059.
7700, 7705, 7706, 7732, 7738, 7746, 7785, 7846, 7851, 7862, 7864, 7866, 7901, 7902, 7910,
7915, 7950, 7958, 7973, 7975, 7981, 7984, 7989, 7990, 8008, 8010, 8058, 8061 and 8064.
7676, 7686 and 7807.
8049.
01
04
LOCATION OF VSB:
01
02
03
04
J070000-25-07
J070000-25-08
J070000-25-09
J070000-25-10
EFFECTIVITY:
1112
D
PRE-MOD
AFT A TTACHMENT SHOWN (TYPICAL)
LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE
VIEW LOOKING DOWN
03
02

### Page 34

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 34 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 11 of 12)
D
LBL
29.31
LEGEND
  3. Pin assy, shear
      3862134-501.
  5. Pin assy, shear
      3862134-503.
13. Hook assy (no serrations).
14. Outboard tube assy
      (no serrations).
3
5
1314
D
POST-MOD
AFT A TTACHMENT SHOWN (TYPICAL)
LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE
VIEW LOOKING DOWN
E
E
rsb601r25206_004.cgm, gd, gb, may9/2023
C
POST-MOD
OVERHEAD BIN SHOWN (TYPICAL)
LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE
VIEW LOOKING DOWN
EFFECTIVITY:
All aircraft.
NOTE
Only installed on aircraft 8049 on overhead bin assembly 4R.1
1

### Page 35

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 35 of 38
Jun 29/2023
Overhead Bin Rework
Figure 1 (Sheet 12 of 12)
UPPER HOOK
ASSY (REF)
F
3
5
4 OUTBOARD TUBEASSY (REF)
LOWER HOOK
(REF)
DRILL HOLE DIAMETER
0.311 TO 0.318 in.
(7.90 TO 8.08 mm)
OUTBOARD TUBE
ASSY (INBOARD HOLE) (REF)
DRILL HOLE DIAMETER
0.198 TO 0.204 in.
(5.03 TO 5.18 mm)
OUTBOARD TUBE
ASSY (OUTBOARD HOLE) (REF)
DIAMETER
0.315 TO 0.322 in.
(8.00 TO 8.18 mm)
UPPER HOOK ASSY (REF)
SHEAR PIN AXIS 
F
POST-MOD
OUTBOARD TUBE DIMENSIONS SHOWN FOR BIN INSTALLATION (TYPICAL)
LOWER HOOK AND SHEAR PIN ASSY NOT SHOWN
FOR CLARITY
LEGEND
3. Pin assy, shear
    3862134-501
4. Screw, csk head
    NAS514P1032-6
5. Pin assy, shear
    3862134-503
rsb601r25206_005.cgm, gd, gb, may9/2023
POST-MOD
TYPICAL 10 PLACES
VIEW LOOKING AFT ON AFT BIN A TTACHMENT
LEFT SIDE SHOWN
RIGHT SIDE OPPOSITE
EFFECTIVITY:
All aircraft.
E - E
SPRING LOADED PIN
(2 PLACES)
NOTE
Only installed on aircraft 8049 on overhead bin assembly 4R.1
1
3
5 1

### Page 36

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 36 of 38
Jun 29/2023
Drill Bushing and Double Margins Step Drill
Figure 2
DRILL HOLE DIAMETER
0.156 in. (3.97 mm)
15
OUTBOARD TUBE (REF)
DRILL BUSHING LOCATION FOR 5/32 DRILLING PROCESS
(TYPICAL 10 PLACES)
LOWER HOOK NOT SHOWN FOR CLARITY
16
DOUBLE MARGINS STEP DRILL
OUTBOARD TUBE
INBOARD WALL (REF)
OUTBOARD TUBE
OUTBOARD WALL (REF)
HOLE DIAMETER
0.311 TO 0.318 in.
(7.90 TO 8.08 mm)
OUTBOARD TUBE (REF)
LEGEND
15. Drill Bushing.
16. Double Margin Step Drill.
UPPER HOOK A SSY (REF)
DIAMETER
0.315 TO 0.322 in.
(8.00 TO 8.18 mm)
rsb601r25206_006.cgm, gd, gb, may17/2023
HOLE DIAMETER
0.198 TO 0.204 in.
(5.03 TO 5.18 mm)
OUTBOARD TUBE (REF)

### Page 37

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 37 of 38
Jun 29/2023
3. MATERIAL INFORMATION
A. Kit Information
None.
NOTE: To complete this service bulletin, a quantity of ten shear pins
3862134-501 and ten screws (NAS514P1032-6) are supplied in the
Safran parts kit (except for aircraft 8049 the quantity is nine shear pins
3862134-501 and one shear pin 3862134-503).
B. Consumable Information
The materials that follow are necessary to do this service bulletin. You can order
them from MHIRJ or purchased directly from industry sources. If the material is
ordered from MHIRJ, there can be some lead time because of the shelf life of the
material.
CONSUMABLES
SPECIFICATION QTY NAME REFERENCE
MIL-DTL-81706
Class1A
As
necessary
Chemical
Conversion Coating
05-025 ¡
¡  Refer to AMM 51-31-00-990-801
NOTE: To complete this list of consumables, refer to the different tasks and the
Safran service bulletins that are given as references in this service bulletin
C. Special Tools and Equipment
For a list of special tools and equipment, refer to the different tasks and the Safran
service bulletins that are given as references in this service bulletin.
NOTE: Tool kit 3861101-507-RTK (drill bushing and double margin step drill)
is supplied by Safran.
D. Disposition of Parts
PRE‐SB
PART NUMBER
NAME QTY DC POST ‐SB
PART NUMBER
3861151-501 Overhead Bin SupportAssembly 2 MOD KCM601R41057-1

### Page 38

SERVICE BULLETIN  601R-25-206
SB 601R-25-206
Page 38 of 38
Jun 29/2023
PRE‐SB
PART NUMBER
POST ‐SB
PART NUMBER
DCQTYNAME
3861151-503 Overhead Bin SupportAssembly 2 MOD KCM601R41057-3
3861151-505 Overhead Bin SupportAssembly 2 MOD KCM601R41057-5
3861151-507 Overhead Bin SupportAssembly 1 MOD KCM601R41058-7
3861151-509 Overhead Bin SupportAssembly 1 MOD KCM601R41057-9
3861151-511 Overhead Bin SupportAssembly 1 MOD KCM601R41057-11
3861151-513 Overhead Bin SupportAssembly 1 MOD KCM601R41057-13
3861151-515 Overhead Bin SupportAssembly 1 MOD KCM601R41057-15
3861151-517 Overhead Bin SupportAssembly 1 or2 MOD KCM601R41058-17
C671151-503 Overhead Bin SupportAssembly 2 MOD KCM601R41060-3
C671151-505 Overhead Bin SupportAssembly 2 MOD KCM601R41060-5
C671151-507 Overhead Bin SupportAssembly 2 MOD KCM601R41060-7
C671151-509 Overhead Bin SupportAssembly 2 MOD KCM601R41060-9
C671151-511 Overhead Bin SupportAssembly 1 MOD KCM601R41060-11
C671151-513 Overhead Bin SupportAssembly 1 MOD KCM601R41060-13
Disposition code (DC):
MOD: Modification: For modification of part, refer to the procedure given in this
service bulletin.
1

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
