# Bombardier Service Bulletin 601R-27-160

## Copies (2)

Copies the FAA filed in AD dockets on regulations.gov, newest revision first. A newer revision may exist.

- Revision D ("601R-27-160D"), 99 pages: PDF https://openairdocs.org/files/sha256/e4/f0/e4f07e28c3df2046eaec995cc50dc5663cc220cd3d2df1b3da93baeffde44e78; text https://openairdocs.org/service-documents/bombardier/601r-27-160/file/e4f07e28c3df.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2016-7427; AD 2016-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Revision A ("U.S. DOT/FAA - SB 601R-27-160rA"), 22 pages: PDF https://openairdocs.org/files/sha256/e5/5c/e55cb957ea0a471756f6fa2eb59c28837009401fc840ba423dfc1468e7d44987; text https://openairdocs.org/service-documents/bombardier/601r-27-160/file/e55cb957ea0a.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2012-0639; AD 2013-02-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 601R-27-160
- Latest revision known: 601R-27-160, Revision D, dated October 22, 2015 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/601r-27-160

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2016-23-07](https://openairdocs.org/ad/2016-23-07.md), effective Dec 30, 2016: Revisions A, B, C and D
- [AD 2013-02-08](https://openairdocs.org/ad/2013-02-08.md), effective Mar 11, 2013: Revision A

Also cited in [2 proposed ADs](https://openairdocs.org/service-documents/bombardier/601r-27-160/proposed.md).

## Text (99 pages)

Revision D, the newest copy. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2016-7427; AD 2016-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

the evolution of mobility
SB 601R- - - 27- - - 160
Page 1 of 1
Oct 22/2015
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
CL- - -600- - -2B19 Canadair Regional Jet (CRJ) Aircraft
SERVICE BULLETIN 601R - - -27 - - -160
SUBJECT : Flight Controls - - - Horizontal Stabilizer Trim Actuator (HSTA) - - -
Serialization of the HSTA Pins and Trunnions
This page transmits:
Revision D of Service Bulletin 601R- - - 27- - - 160, dated Oct 22/2015
For aircraft that have had the initial issue or Revision A of this
service bulletin incorporated, it is necessary to do PART B of this
service bulletin.
The changes in this revision have no effect on aircraft that have had
Revision B or Revision C of this service bulletin incorporated.
Reason:
Revised Accomplishment Instructions, paragraph 2., to:
Add a note in the Job Set-Up section of PARTA
Add a step in the Procedure section of PART A
Add a note and change a table in the Procedure section of PART A
Add a note in the Job Close-Out section of PART A
Add a note in the Job Set-Up section of PART B
Add some steps and a note in the Procedure section of PART B
Add a note in the Job Close-Out section of PART B
This revision also includes small editorial changes that do not have an effect on the technical
content.
Instructions:
Discard the copy of Service Bulletin 601R- - - 27- - - 160, Revision C, dated May 04/2015.
Replace with the copy attached.
Service Bulletin History:
Initial issue, dated Sep 29/2011
Revision A, dated Oct 03/2012
Revision B, dated Feb 20/2015
Revision C, dated May 04/2015
1

### Page 2

the evolution of mobility
SB 601R−27−160
Page 1 of 97
Sep 29/2011
Revision D, Oct 22/2015
SERVICE BULLETIN
Technical
Publications
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS LEASED AIRCRAFT ,
TRANSFERRED SPARES IN THE LAST SIX MONTHS, SEND THIS SERVICE BULLETIN TO THE NEW
OWNER, UNLESS CONFIRMATION WAS RECEIVED THAT BOMBARDIER HAS INCLUDED THE NEW
OPERATOR ON THE DISTRIBUTION LIST .
SEND THIS SERVICE BULLETIN TO THE LESSEE. IF THE OPERATOR HAS SOLD AIRCRAFT OR
ATA SYSTEM: 27−42 NUMBER: 601R−27−160
SUBJECT:  Flight Controls − Horizontal Stabilizer Trim Actuator (HSTA) −
Serialization of the HSTA Pins and Trunnions
1. PLANNING INFORMATION
A. Effectivity
(1) Aircraft Affected:
Service Bulletin: CL−600−2B19 aircraft with serial numbers 7003 thru 7067,
7069 thru 7990, 8000 thru 8113.
Production: Aircraft serial number 8114 and subsequent serial numbers
will have an equivalent modification incorporated before
delivery.
 NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier service bulletins. Before you do this service
bulletin, examine all Supplemental Type Certificates (STCs), and
Supplemental Type Approvals (STAs) or alternative action changes
to make sure you can complete this service bulletin.

### Page 3

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 2 of 97
Sep 29/2011
Revision D, Oct 22/2015
B. Reason
(1) Condition
The pins and the trunnions of the HSTA are not serialized. Therefore, it is
not possible to keep a record of the life of the pins and the trunnions
installed on the HSTA. 
The pins and/or the trunnions of the HSTA can have a non-conformance
report (NCR) condition, and it is possible that the pins and/or the
trunnions of the HSTA are not properly identified.
(2) Evidence
Operators have reported HSTA pins and trunnions with a NCR condition.
(3) Objective/Benefit
This service bulletin gives the procedure to inspect the HSTA pins, the
trunnions, and their attach holes, and the aircraft structure attach holes. This
service bulletin also gives the procedure to identify and serialize the pins and
the trunnions.
The inspection of the attach holes will make sure that the pins and the
trunnions are installed correctly. The identification and the serialization of the
pins and the trunnions, on the attachments of the HSTA, will give traceability
and service history to agree with Federal Aviation Regulation FAR 25.1529.
C. Description
This service bulletin is divided into 2 parts: PART A and PART B.
PART A − Inspection and Serialization of the HSTA Pins, and Trunnions
Access panels are removed. Circuits breakers are opened. The HSTA is removed.
An inspection is done to the HSTA pins, the trunnions, and their attach holes, and
to the aircraft structure attach holes. The pins and the trunnions are identified, and
serialized. If necessary, the pins and/or the trunnions are replaced. The HSTA is
installed. Return-to-service tests are done.
PART B − Inspection of the Attach Holes of the HSTA Pins, and Trunnions
Access panels are removed. Circuits breakers are opened. The HSTA is removed.
An inspection is done to the attach holes of the HSTA pins and trunnions, and to
the aircraft structure attach holes. If necessary, the identification of the pins and/or
the trunnions are changed. If necessary, the pins and/or the trunnions are replaced.
The HSTA pins and the trunnions are examined for damage. The HSTA is installed.
Return-to-service tests are done.

### Page 4

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 3 of 97
Sep 29/2011
Revision D, Oct 22/2015
D. Compliance
Recommended service bulletin.
For aircraft that have not incorporated the initial issue or Revision A of this service
bulletin.
Bombardier recommends that PART A of this service bulletin be done at no more
than 5000 flight hours, or no later than 5 years from the initial release date of this
service bulletin, or no later than the subsequent inspection of Airworthiness
Limitation (AWL) 27−40−102 of the Maintenance Requirements Manual (MRM) Part
2, Appendix B, whichever comes first, or unless otherwise directed by the
airworthiness authority of the operator.
For aircraft that have had the initial issue or Revision A of this service bulletin
incorporated
Bombardier recommends that PART B of this service bulletin be done at no more
than 9600 flight hours, or no later than 5 years from the release date of revision B of
this service bulletin, which ever comes first, unless otherwise directed by the
airworthiness authority of the operator.
For all aircraft
NOTE: If it is not possible to complete all th e instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
Bombardier in the Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com for analysis and to get an approved
disposition to complete this service bulletin.
This service bulletin affects Airworthiness Limitations (AWLs) and/or Damage
Tolerance Inspections (DTIs). Reference applicable Pre/Post Modsum
TC601R18078, TC601R18419, and/or service bulletin 601R−27−160 in the (MRM).
E. Approval
The technical content of this service bulletin has been approved under the authority
of the TCCA Design Approval Organization No: DAO #93−Q−02.
F . Manpower
The man-hours given below are estimates for direct labor done by an experienced
crew on an aircraft prepared for maintenance.
These estimates do not include the time necessary for:
−Administrative functions such as planning, liaising, familiarization, and report writing.
−Non-productive elapsed time such as rest time, having meals, and crew shift
changes.

### Page 5

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 4 of 97
Sep 29/2011
Revision D, Oct 22/2015
−Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
−Preparation for modification (unless specified in the Accomplishment
Instructions) such as cleaning and getting parts, tools, consumables, and
ground equipment.
−Quality assurance inspections, troubleshooting and/or correction of
discrepancies found when a task is done.
−All other activities that are not considered by Bombardier as directly related to the
accomplishment of this procedure.
NOTE: For on-site labor assistance, please speak with a Fleet Services
representative for an estimate. Call the Fleet Services Team through the
CRC at 1−844−272−2720 (1−844−CRC−CRC0) or 1−514−855−8500 or
e-mail at thd.crj@aero.bombardier.com.
PART A − Inspection and Serialization of the HSTA Pins, and Trunnions
It will take an estimated 22.0 man-hours to complete PART A of this service
bulletin. The man-hours are divided in the table that follows (elapsed cure time
is not included in the man-hour summary given above):
TASK MAN-HOURS
(1)  Job Set-Up 8.0
(2)  Procedure 3.0
(3)  Test 3.0
(4)  Job Close-Out 8.0
NOTE: The man-hours for the procedure do not include the hours to replace
damaged parts.
PART B − Inspection of the Attach Holes of the HSTA Pins and Trunnions
It will take an estimated 20.0 man-hours to complete PART B of this service
bulletin. The man-hours are divided in the table that follows (elapsed cure time
is not included in the man-hour summary given above):
TASK MAN-HOURS
(1)  Job Set-Up 8.0
(2)  Procedure 1.0

### Page 6

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 5 of 97
Sep 29/2011
Revision D, Oct 22/2015
TASK MAN-HOURS
(3)  Test 3.0
(4)  Job Close-Out 8.0
NOTE: The man-hours for the procedure do not include the hours to replace
damaged parts.
G. Material − Price and Availability
(1) The parts in the table that follows are/can be necessary to do this service
bulletin and are available from Bombardier.
PART NUMBER NAME QTY ALTERNATIVE PARTNUMBER /C0001
601R92309−3 Lower pin 2 601R92309−1 or601R92309−1PP
601R92310−3 Upper pin 2 601R92310−1 or601R92310−1PP
601R92386−3 Trunnion 4 601R92386−1
NAS42DD6−25 Spacer 4 −
NAS42DD8−25 Spacer 4 −
K601R92308−51 /C0019 Trunnion 4 −
K601R92308−53 /C0019 Lower pin 2 −
K601R92308−55 /C0019 Upper pin 2 −
NAS1580A3R8DX Bolt, 1st oversize 4 −
NAS1580A3R8DY Bolt, 2nd oversize 4 −
NAS1580A3R13DX Bolt, 1st oversize 4 −
NAS1580A3R13DY Bolt, 2nd oversize 4 −
NAS8604D8 Bolt, nominal 4 −
NAS8604D8X Bolt, 1st oversize 4 −
NAS8604D8Y Bolt, 2nd oversize 4 −
/C0001 If the alternative part number is ordered, it is necessary to give a serial number and
change the identification of the part as given in this service bulletin.
/C0019 These parts are necessary only if a NCR condition is found during the inspection.

### Page 7

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 6 of 97
Sep 29/2011
Revision D, Oct 22/2015
(2) Please send a purchase order to the address below to schedule part
delivery:
Bombardier
Service Bulletin Kit Support Team
123 Garratt Blvd, N42−24
Toronto, Ontario
Canada  M3K 1Y5
Fax:     416-375-3060
Phone: 416-375-3920
e-mail: sbkits@aero.bombardier.com
Please contact the Service Bulletin Kit Support Team at the address above for
terms and conditions.
(3) The kits in the tables that follow are available from Bombardier.
 NOTE: For a list of kit contents, refer to paragraph 3.A.
KIT NUMBER NAME
601R27−160K1/C0001 HSTA − Laminated Shims Kit
601R27−160K2/C0001 HSTA − Nominal Hardware Kit
601R27−160K3/C0019 HSTA − Trunnion Oversize Hardware Kit
601R27−160K4/C0019 HSTA − Pin Oversize Hardware Kit
/C0001 One kit for each aircraft.
/C0019 One kit for each operator. To replace parts taken from the kit
601R27−160K3 and 601R27−160K4, speak with a representative of the
Service Bulletin Kit Support Team at the address below.
(4) Please send a purchase order to the address below to schedule kit delivery:
Bombardier
Service Bulletin Kit Support Team
123 Garratt Blvd, N42−24
Toronto, Ontario
Canada  M3K 1Y5
Fax:     416-375-3060
Phone: 416-375-3920
e-mail: sbkits@aero.bombardier.com
Please contact the Service Bulletin Kit Support Team at the address above for
terms and conditions.
(5) Refer to paragraph 3.B. for a list of consumables for this service bulletin.

### Page 8

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 7 of 97
Sep 29/2011
Revision D, Oct 22/2015
For Business/Corporate Operators
All Business/Corporate operators (i.e. operators who do not have a commercial airline
operation) refer to SB 800-00-004 for commercial policy coverage and logistics/planning
arrangements (refer to www.cic.bombardier.com/technical library/service
bulletins/challenger/850/SB 800-00-004).
To place an order for parts or kits, please call Bombardier Parts Logistics at
514-855-2999 or 1-866-538-1247.
H. Tooling − Price and Availability
There are no tool kits for this service bulletin. Refer to paragraph 3.C. for a list of special
tools and equipment for this service bulletin.
I. Weight and Balance
Not changed.
J. Electrical Load Data
Not changed.
K. References
Refer to the SB Introduction document for definition or explanation of service
bulletin content.
Restriction and/or Special Instruction (RSI) C−A275, Revision F
Modification Summary TC601R18078, Revision D−1
Modification Summary TC601R18419, Revision D
Generic Repair Engineering Order (GREO) 601R−27−42−007, Rev B or latest
approved version
Generic Repair Engineering Order (GREO) 601R−27−42−008, Rev A, or latest
approved revision
Aircraft Maintenance Manual (AMM)
Structural Repair Manual (SRM)
Maintenance Requirement Manual (MRM)
Nondestructive Testing Manual (NDTM)
For Bombardier reference only: PCA 05479 and PCA 06879
L. Other Publications Affected
Aircraft Maintenance Manual (AMM)
Aircraft Illustrated Parts Catalogue (AIPC)
Maintenance Requirement Manual (MRM)

### Page 9

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 8 of 97
Sep 29/2011
Revision D, Oct 22/2015
M. Relationship Chart
PART A − Inspection and Serialization of the HSTA Pins, and Trunnions
PRE-SB
PART NUMBER NAME POST -SBPART NUMBER NAME
600−92383−5 Lower Pin
601R92309−3 or
K601R92308−11 or
K601R92308−33 or
K601R92308−53
Lower Pin
600−92383−7 Lower Pin
601R92309−3 or
K601R92308−13 or
K601R92308−33 or
K601R92308−53
Lower Pin
601R92309−1 /C0019 Lower Pin
601R92309−3 or
K601R92308−15 or
K601R92308−33 or
K601R92308−53
Lower Pin
601R92309−3 Lower Pin
601R92309−3 or
K601R92308−33 or
K601R92308−53
Lower Pin
NCR# xxxxxx−x /C0001 Lower Pin K601R92308−33 orK601R92308−53 Lower Pin
600−92384−5 Upper Pin
601R92310−3 or
K601R92308−5 or
K601R92308−35 or
K601R92308−55
Upper Pin
600−92384−7 Upper Pin
601R92310−3 or
K601R92308−7 or
K601R92308−35 or
K601R92308−55
Upper Pin
601R92310−1 /C0019 Upper Pin
601R92310−3 or
K601R92308−9 or
K601R92308−35 or
K601R92308−55
Upper Pin
601R92310−3 Upper Pin
601R92310−3 or
K601R92308−35 or
K601R92308−55
Upper Pin

### Page 10

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 9 of 97
Sep 29/2011
Revision D, Oct 22/2015
PRE-SB
PART NUMBER NAMEPOST -SBPART NUMBERNAME
NCR# xxxxxx−x /C0001 Upper Pin K601R92308−35 orK601R92308−55 Upper Pin
601R92386−1 Trunnion
601R92386−3 or
K601R92308−19 or
K601R92308−31 or
K601R92308−51
Trunnion
601R92386−3 Trunnion
601R92386−3 or
K601R92308−31 or
K601R92308−51
Trunnion
NCR# xxxxxx−x /C0001 Trunnion K601R92308−31 orK601R92308−51 Trunnion
/C0001 P/N NCR# xxxxxx−x Can be any numerical and/or letter combination which
identifies a Non-Conformance Part (NCR)
/C0019 Lower pin P/N 601R92309−1PP is an alternative to P/N 601R92309−1 and
upper pin P/N 601R92310−1PP is an alternative to P/N 601R92310−1.
PART B − Inspection of the Attach Holes of the HSTA Pins and Trunnions
PRE-SB
PART NUMBER NAME POST -SBPART NUMBER NAME
601R92309−3 Lower Pin
601R92309−3 or
K601R92308−33 or
K601R92308−53
Lower Pin
K601R92308−11 Lower Pin
601R92309−3 or
K601R92308−11 or
K601R92308−33 or
K601R92308−53
Lower Pin
K601R92308−13 Lower Pin
601R92309−3 or
K601R92308−13 or
K601R92308−33 or
K601R92308−53
Lower Pin
K601R92308−15 Lower Pin
601R92309−3 or
K601R92308−15 or
K601R92308−33 or
K601R92308−53
Lower Pin

### Page 11

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 10 of 97
Sep 29/2011
Revision D, Oct 22/2015
PRE-SB
PART NUMBER NAMEPOST -SBPART NUMBERNAME
NCR# xxxxxx−x /C0001 Lower Pin K601R92308−33 orK601R92308−53 Lower Pin
601R92310−3 Upper Pin
601R92310−3 or
K601R92308−35 or
K601R92308−55
Upper Pin
K601R92308−5 Upper Pin
601R92310−3 or
K601R92308−5 or
K601R92308−35 or
K601R92308−55
Upper Pin
K601R92308−7 Upper Pin
601R92310−3 or
K601R92308−7 or
K601R92308−35 or
K601R92308−55
Upper Pin
K601R92308−9 Upper Pin
601R92310−3 or
K601R92308−9 or
K601R92308−35 or
K601R92308−55
Upper Pin
NCR# xxxxxx−x /C0001 Upper Pin K601R92308−35 orK601R92308−55 Upper Pin
601R92386−3 Trunnion
601R92386−3 or
K601R92308−31 or
K601R92308−51
Trunnion
K601R92308−19 Trunnion
601R92386−3 or
K601R92308−19 or
K601R92308−31 or
K601R92308−51
Trunnion
NCR# xxxxxx−x /C0001 Trunnion K601R92308−31 orK601R92308−51 Trunnion
/C0001 P/N NCR# xxxxxx−x Can be any numerical and/or letter combination which
identifies a Non-Conformance Part (NCR)

### Page 12

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 11 of 97
Sep 29/2011
Revision D, Oct 22/2015
2. ACCOMPLISHMENT INSTRUCTIONS
PART A − Inspection and Serialization of the HSTA Pins and Trunnions
Reference Information
REFERENCE DESIGNATION
AMM 12−00−07−861−801 Connect External AC Power
AMM 20−21−00−910−801 Torque procedures for Threaded Fasteners
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 27−40−00−710−802 Operational Test of the Horizontal Stabilizer Trim
System
AMM 27−41−00−740−801 Functional Check (Ground Maintenance Test) of
the HSTCU
AMM 27−42−01−000−801 Removal of the Horizontal-Stabilizer Trim 
Actuator (HSTA)
AMM 27−42−01−400−801 Installation of the Horizontal-Stabilizer Trim 
Actuator (HSTA)
AMM 51−26−00−110−801 Solvent Cleaning
AMM 55−32−05−000−806 Removal of the Middle Upper Fairing
AMM 55−32−05−400−806 Installation of the Middle Upper Fairing
AMM 55−32−05−000−807 Removal of the Middle Lower Fairing
AMM 55−32−05−400−807 Installation of the Middle Lower Fairing
NDTM 51−20−09−PART 1 Visual-Inspection Procedures
SRM 51−10−06 Damage
SRM 51−21−11 Corrosion Prevention Procedures
SRM 51−23−00 Pressure, Environmental, Fuel Tank and Firewall
Sealing
SRM 51−25−06 Fluid-Resistant (FR) Epoxy Primer
SRM 51−25−16 Fluid-Resistant (FR) Polyurethane Topcoat

### Page 13

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 12 of 97
Sep 29/2011
Revision D, Oct 22/2015
REFERENCE DESIGNATION
SRM 51−26−00 Cleaning
SRM 51−40−11 How to Prepare Fastener Holes
SRM 51−41−02 Bolts, Screws and Related Items
Tolerance Information
Linear Tolerances Angular Tolerance
X.XX in. (X.X mm) X.XXX in. (X.XX mm)
+/−0° 30"+/− 0.03 in. +/− 0.010 in.
+/− 0.8 mm +/− 0.25 mm
NOTE: The tolerances above apply to the dimensions given in this service
bulletin, except when specified differently.
A. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Obey all the electrical/electronic safety precautions
(refer to AMM 24−00−00−910−801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR: FLIGHT CONTROLS FLIGHT CONTROL
SURFACES COMPONENTS THAT MOVE. MAKE SURE THAT THERE
ARE NO PERSONS OR EQUIPMENT ON OR NEAR THE FLIGHT
CONTROL SURFACES. ACCIDENTAL MOVEMENT OF THE FLIGHT
CONTROLS CAN CAUSE INJURIES TO PERSONS AND/OR DAMAGE
TO EQUIPMENT .
(2) Install the applicable warning placards on the pilot’s and the copilot’s control
wheels and the STAB TRIM/MACH TRIM panel.
CAUTION: MAKE SURE THAT THE REAR FUSELAGE SUPPORT IS PUT DIRECTLY
BELOW THE RIVET LINE AT FS755.00 (37 INCHES AFT OF THE
BAGGAGE COMPARTMENT DOOR). IF THE REAR FUSELAGE SUPPORT
IS NOT DIRECTLY BELOW THE RIVET LINE, DAMAGE TO THE AIRCRAFT
CAN OCCUR.

### Page 14

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 13 of 97
Sep 29/2011
Revision D, Oct 22/2015
(3) Remove the access panels that follow:
PANEL NAME REFERENCE
Middle Upper
Fairing Access panel AMM 55−32−05−000−806
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Middle Lower 
Fairing
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Access panel
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
AMM 55−32−05−000−807
B. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
Bombardier in the Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com for analysis and to get an approved disposition
to complete this service bulletin.
NOTE: In the steps and the Figures of this service bulletin, lower pin P/N
601R92309−1PP is an alternative to P/N 601R92309−1 and upper pin
P/N 601R92310−1PP is an alternative to P/N 601R92310−1.
Refer to Figure 1 and/or 2.
(2) Remove the HSTA (20), the trunnions (9), and the pins (1) and (13) from the
aircraft (refer to AMM 27−42−01−000−801 and the steps that follow).
(3) Record the position of the removed trunnions (9), and the pins (1) and (13).
(4) Discard the cotter pins (2), (12), and (18), the laminated shims (8), the
washers (10), the nuts (3), (11), and (17).
(5) Measure the diameter of the bolts (7), (15), and (19) that attach the trunnions
(9), and do the steps that follow:
(a) Discard the bolt(s) (7), (15), and/or (19) that have a nominal diameter of
0.375 in. (9.53 mm).
Refer to Figure 1.
(b) For the bolt(s) (7), (15), and/or (19) that have an oversize diameter of
0.390 in. (9.91 mm) or more, do as follows:
1 It is permissible to keep the oversize bolt(s) (7), (15), and/or (19)
for a subsequent step.

### Page 15

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 14 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: It is possible that the bolt(s) (7), (15), and/or (19) with a
different diameter can be necessary to install at the end of
this procedure.
2 Make sure that the oversize bolt(s) (7), (15), and (19) are the
correct length before the installation of the trunnions (9) in a
subsequent step (refer to Table 5).
Refer to Figure 1 and/or 2.
(6) Measure the diameter of the bolts (6) and (14) that attach the upper pins
(1) and the lower pins (13), and do the steps that follow:
Refer to Figure 2.
(a) For the bolt(s) (6) and/or (14) that have a nominal diameter of 0.189
in. (4.80 mm) do as follows:
1 It is permissible to keep the nominal diameter bolt(s) (6) and/or
(14) for a subsequent step.
2 It is permissible to keep the washer(s) (4) and/or (16) for a
subsequent step.
Refer to Figure 1.
(b) For the bolt(s) (6) and/or (14) that have an oversize diameter of
0.205 in. (5.21 mm) or more, do as follows:
1 It is permissible to keep the oversize diameter bolt(s) (6)
and/or (14) for a subsequent step.
NOTE: It is possible that the bolt(s) (6) and/or (14) with a
different diameter can be necessary to install at the end
of this procedure.
2 Make sure that the oversize bolt(s) (6) and (14) are the correct
length before the installation of the upper pins (1) and the lower
pins (13) in a subsequent step (refer to Table 7 and Table 9).
3 Discard the washer(s) (4) and/or (16).
Refer to Figure 1 and/or 2.
(7) For the trunnions (9), do the procedure that follows.
 NOTE: This procedure is applicable to all four trunnions (9). The procedure
that follows is written for only one trunnion (9).

### Page 16

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 15 of 97
Sep 29/2011
Revision D, Oct 22/2015
(a) Clean the aircraft structure with solvent where the trunnion was
installed (refer to SRM 51−26−00).
(b) Measure the diameter of the two attach holes in the aircraft
structure.
TABLE 1 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND TRUNNION
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE TRUNNION
HOLE
CONDITION NCR CONDITION
0.375 to 0.380 in.
(9.53 to 9.65 mm)
0.375 to 0.380 in.
(9.53 to 9.65 mm) Nominal No
0.391 to 0.396 in.
(9.93 to 10.06 mm)
0.391 to 0.396 in.
(9.93 to 10.06 mm) 1st oversize Yes
0.406 to 0.411 in.
(10.31 to 10.44 mm)
0.406 to 0.411 in.
(10.31 to 10.44 mm) 2nd oversize Yes
0.438 to 0.443 in.
(11.13 to 11.25 mm)
0.438 to 0.443 in.
(11.13 to 11.25 mm) Next size Yes
0.453 to 0.458 in.
(11.51 to 11.63 mm)
0.453 to 0.458 in.
(11.51 to 11.63 mm) 1st oversize Yes
0.469 to 0.474 in.
(11.91 to 12.04 mm)
0.469 to 0.474 in.
(11.91 to 12.04 mm) 2nd oversize Yes
0.500 to 0.505 in.
(12.70 to 12.83 mm)
0.500 to 0.505 in.
(12.70 to 12.83 mm) Next size Yes
(8) If the diameter of the attach hole(s) in the aircraft structure do not agree with
Table 1, speak with a representative of the Bombardier Customer Response
Center at +1−844−272−2720 (1−844−CRC−CRC0) or +1−514−855−8500
or e-mail at thd.crj@aero.bombardier.com to get an approved disposition.
(9) If the diameter of the attach holes in the aircraft structure are a nominal
dimension of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to Table 1), do as
follows:
(a) Measure the diameter of the attach holes in the trunnion (9).
(b) If the diameter of the attach hole(s) in the trunnion (9) is/are more than
0.380 in. (9.65 mm), do as follows:
1 Discard the trunnion (9).
2 Get a trunnion (9) P/N 601R92386−3 or alternative.
NOTE: Trunnion P/N 601R92386−1 is a permitted alternative if
trunnion P/N 601R92386−3 is not available.

### Page 17

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 16 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: The identification and the serialization procedure is not
necessary because the trunnion P/N 601R92386−3 is
identified and serialized.
3 Increase the diameter of the attach holes in the trunnion (9) to a
diameter of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to Table 1).
4 Remove the burrs and the sharp edges from the trunnion (9).
5 Apply a chemical conversion coating on the bare metal surfaces of
the trunnion (9) (refer to SRM 51−21−11).
(c) If the diameter of the attach hole(s) in the trunnion (9) is/are a nominal
dimension of 0.375 to 0.380 in. (9.53 to 9.65 mm), do as follows:
1 Do a detailed visual inspection of the trunnion (9) for gouge(s),
scratch(es), and corrosion (refer to NDTM 51−20−09 PART 1).
2 If gouge(s), and/or scratch(es), and/or corrosion is/are found on
the trunnion (9), do revision B or the latest approved revision of
GREO 601R−27−42−007.
3 If the trunnion (9) cannot be repaired with revision B or the latest
approved revision of GREO 601R−27−42−007, do as follows:
a Discard the trunnion (9).
b Get a trunnion (9) P/N 601R92386−3 or alternative.
NOTE: Trunnion P/N 601R92386−1 is a permitted alternative
if trunnion P/N 601R92386−3 is not available.
NOTE: The identification and serialization procedure is not
necessary because the trunnion P/N 601R92386−3 is
identified and serialized.
c Increase the diameter of the attach holes in the trunnion (9) to
a diameter of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to
Table 1).
d Remove the burrs and the sharp edges from the trunnion (9).
e Apply a chemical conversion coating on the bare metal
surfaces of the trunnion (9) (refer to SRM 51−21−11).
(d) If the trunnion (9) is replaced with P/N 601R92386−3, record the serial
number in the applicable logbooks.
(e) If the trunnion (9) is replaced with the trunnion P/N 601R92386−1, refer
to step 2.B.(24) to change the identification to K601R92308−19 and to
add a serial number.

### Page 18

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 17 of 97
Sep 29/2011
Revision D, Oct 22/2015
(f) If the trunnion (9) is repaired with revision B or the latest approved
revision of GREO 601R−27−42−007, or if no gouge(s), and/or
scratch(es), and/or corrosion is/are found, do as follows:
1 For the trunnion (9) P/N 601R92386−1, refer to step 2.B.(24) to change
the identification and to add a serial number.
2 For the trunnion (9) P/N 601R92386−3, the identification and
serialization procedure is not necessary because the trunnion is
identified and serialized.
(10) If the diameter of the attach hole(s) in the aircraft structure is/are an oversized
dimension of more than 0.380 in. (9.65 mm) and equal to or less than 0.505 in.
(12.83 mm) (refer to Table 1), do as follows:
(a) Measure the diameter of the related attach holes in the trunnion (9).
(b) If the diameters of the attach holes in the trunnion (9) agree with the
diameter of the related attach holes in the aircraft structure
(refer to Table 1), do as follows:
1 Make sure that the edge distance of the attach holes in the trunnion
(9) are a minimum of 0.9D.
2 If the edge distance of the attach hole(s) in the trunnion (9) is/are less
than 0.9D, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get
an approved disposition.
3 Do a detailed visual inspection of the trunnion (9) for gouge(s),
scratch(es) and corrosion (refer to NDTM 51−20−09 PART 1).
4 If gouge(s), and/or scratch(es), and/or corrosion is/are found, do
revision B or the latest approved revision of GREO
601R−27−42−007.
5 If the trunnion (9) cannot be repaired with revision B or the latest
approved revision of GREO 601R−27−42−007, go to step 2.B.(11)
for the replacement of the trunnion (9).
(c) If the diameter of the attach hole(s) in the trunnion (9) do not agree with
the diameter of the related attach hole(s) in the aircraft structure (refer to
Table 1), do as follows:
1 If the diameter of the related attach hole(s) in the trunnion (9) is/are
larger than the related attach hole(s) in the aircraft structure, do as
follows:

### Page 19

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 18 of 97
Sep 29/2011
Revision D, Oct 22/2015
a Discard the trunnion (9).
b Go to step 2.B.(11) for the replacement of the trunnion (9).
2 If the diameter of the attach hole(s) in the trunnion (9) is/are smaller
than the related attach hole(s) in the aircraft structure, do as
follows:
a Increase the diameter of the attach hole(s) in the trunnion (9) to
agree with the related NCR condition in the aircraft structure (refer
to Table 1).
b Make sure that the edge distance for the attach holes in the
trunnion (9) are a minimum of 0.9D.
c If the edge distance for the attach hole(s) in the trunnion (9) is/are
less than 0.9D, speak with a representative of the Bombardier
Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
d Remove the burrs and the sharp edges from the trunnion (9).
e Apply a chemical conversion coating on the bare metal
surfaces of the trunnion (9) (refer to SRM 51−21−11).
f Do a detailed visual inspection of the trunnion (9) for
gouge(s), scratch(es), and corrosion
(refer to NDTM 51−20−09 PART 1).
g If gouge(s), and/or scratch(es) and/or corrosion is/are found,
do revision B, or the latest approved revision of GREO
601R−27−42−007.
h If the trunnion (9) cannot be repaired with revision B or the
latest approved revision of GREO 601R−27−42−007, go to
step 2.B.(11) for the replacement of the trunnion (9).
(d) If the trunnion (9) is repaired with revision B, or the latest approved
revision of GREO 601R−27−42−007, or if no gouge(s), and/or
scratch(es), and/or corrosion is/are found, go to step 2.B.(24) to change
the identification and to add a serial number.

### Page 20

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 19 of 97
Sep 29/2011
Revision D, Oct 22/2015
(11) To replace the trunnion (9) that has an oversized attach hole(s) (NCR
condition) in the aircraft structure of more than 0.380 in. (9.65 mm) and equal
to or less than 0.505 in. (12.83 mm) do as follows:
(a) Replace the trunnion (9) where there is a NCR condition with trunnion
P/N K601R92308−51.
 NOTE: The identification and the serialization procedure is not necessary as the
trunnion P/N K601R92308−51 is identified and serialized.
(b) Align the center hole of the trunnion (9) with the center hole of the
aircraft structure and attach temporarily.
(c) As necessary, make marks on the trunnion (9) to find the correct center
points of the aircraft structure attach holes.
(d) Remove the temporarily attached trunnion (9) from the aircraft
structure.
(e) Make sure that the edge distance for the attach holes in the trunnion (9)
are a minimum of 0.9D.
(f) If the edge distance for the attach hole(s) in the trunnion (9) is/are less
than 0.9D, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get
an approved disposition.
(g) Drill the center point of the attach holes in the trunnion (9) to a diameter
of .098 in. (2.49 mm).
(h) Increase the diameter of the attach holes in the trunnion (9) to agree with
the related NCR condition in the aircraft structure (refer to Table 1).
(i) Remove the burrs and sharp edges from the trunnion (9).
(j) Apply a chemical conversion coating on the bare metal surfaces of the
trunnion (9) (refer to SRM 51−21−11).
(k) Record the serial number of the trunnion (9) in the applicable logbooks.
(12) For the upper pins (1), do the procedure that follows.
 NOTE: This procedure is applicable to the two upper pins (1). The procedure
that follows is written for only one upper pin (1).

### Page 21

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 20 of 97
Sep 29/2011
Revision D, Oct 22/2015
(a) Clean the aircraft structure with solvent where the pin is attached
(refer to SRM 51−26−00).
(b) Measure the diameter of the two attach holes in the aircraft structure.
TABLE 2 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND UPPER PIN
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE UPPER PIN
HOLE CONDITION NCR CONDITION
0.189 to 0.195 in
(4.80 to 4.95 mm)
0.215 to 0.225 in
(5.46 to 5.72 mm) Nominal No
0.205 to 0.210 in
(5.21 to 5.33 mm)
0.225 to 0.235 in
(5.72 to 5.97 mm) 1st oversize Yes
0.221 to 0.226 in
(5.61 to 5.74 mm)
0.239 to 0.249 in
(6.07 to 6.32 mm) 2nd oversize Yes
0.250 to 0.255 in
(6.35 to 6.48 mm)
0.270 to 0.280 in
(6.86 to 7.11 mm) Next size Yes
0.265 to 0.270 in
(6.73 to 6.86 mm)
0.284 to 0.294 in
(7.21 to 7.47 mm) 1st oversize Yes
0.281 to 0.286 in
(7.14 to 7.26 mm)
0.299 to 0.309 in
(7.59 to 7.85 mm) 2nd oversize Yes
(13) If the diameter of the attach hole(s) in the aircraft structure do not agree with the
diameters in Table 2, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get an
approved disposition.
(14) If the diameter of the attach holes in the aircraft structure are a nominal
dimension of 0.189 to 0.195 in. (4.80 to 4.95 mm) (refer to Table 2),
do as follows:
(a) Measure the diameter of the attach hole(s) in the upper pin (1).
(b) If the diameter of the attach hole(s) in the upper pin (1) is/are more than
0.225 in. (5.72 mm) (refer to Table 2), do as follows:
1 Discard the upper pin (1).
2 Get an upper pin (1) P/N 601R92310−3 or alternative.
NOTE: Upper pin P/N 600−92384−5, or P/N 600−92384−7, or P/N
601R92310−1 are permitted alternatives if upper pin P/N
601R92310−3 is not available.

### Page 22

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 21 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: If the upper pin (1) is replaced with P/N 601R92310−3, the
identification and the serialization procedure is not
necessary because the new part is identified and serialized.
(c) If the diameter of the attach holes in the upper pin (1) are a nominal
dimension of 0.215 to 0.225 in. (5.46 to 5.72 mm) (refer to Table 2), do
as follows:
1 Do a detailed visual inspection of the upper pin (1) for gouge(s),
scratch(es), and corrosion (refer to NDTM 51−20−09 PART 1).
2 If gouge(s), and/or scratch(es), and/or corrosion is/are found, do
revision A, or the latest approved revision of GREO
601R−27−42−008.
3 If the upper pin (1) cannot be repaired with revision A or the latest
approved revision of GREO 601R−27−42−008, do as follows:
a Discard the upper pin (1).
b Get an upper pin (1) P/N 601R92310−3 or alternative.
NOTE: Upper pin P/N 600−92384−5 or 600−92384−7 or
601R92310−1 are permitted alternatives if P/N
601R92310−3 is not available.
NOTE: If the upper pin (1) is replaced with an upper pin P/N
601R92310−3, the identification and the serialization
procedure is not necessary because the new part is
identified and serialized.
(d) If the upper pin (1) is replaced with P/N 601R92310−3, record the serial
number in the applicable logbooks.
(e) If the upper pin (1) is replaced with P/N 600−92384−5 or 600−92384−7
or 601R92310−1, go to step 2.B.(24) for the identification and the
serialization procedure.
(f) If the upper pin (1) is repaired with revision A or the latest approved
revision of GREO 601R−27−42−008, or if no gouge(s), and/or
scratch(es), and/or corrosion is/are found do as follows:
1 For the upper pin (1) P/N 600−92384−5, or 600−92384−7, or
601R92310−1, refer to step 2.B.(24) to change the identification and to
add a serial number.
2 For the upper pin (1) P/N 601R92310−3, the identification and
serialization procedure is not necessary because the pin is identified
and serialized.

### Page 23

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 22 of 97
Sep 29/2011
Revision D, Oct 22/2015
(15) If the diameter of the attach hole(s) in the aircraft structure is/are an oversized
dimension of more than 0.195 in. (4.95 mm) and equal to or less than 0.286
in. (7.26 mm) (refer to Table 2), do as follows:
(a) Measure the diameter of the attach holes in the upper pin (1).
(b) If the diameters of the attach holes in the upper pin (1) agree with the
diameter of the related attach holes in the aircraft structure (refer to Table 2),
do as follows:
1 Make sure that the edge distance for the attach holes in the upper
pin (1) are a minimum of 0.9D.
2 If the edge distance for the attach hole(s) in the upper pin (1) is/are less
than 0.9D, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get
an approved disposition.
3 Do a detailed visual inspection of the upper pin (1) for gouge(s),
scratch(es), and corrosion (refer to NDTM 51−20−09 PART 1).
4 If gouge(s), and/or scratch(es) and/or corrosion is/are found, do
revision A or the latest approved revision of GREO
601R−27−42−008.
5 If the upper pin (1) cannot be repaired with revision A or the latest
approved revision of GREO 601R−27−42−008, go to step 2.B.(16)
for the replacement of the upper pin (1).
(c) If the diameter of the attach hole(s) in the upper pin (1) do not agree with
the diameter of the related attach hole(s) in the aircraft structure (refer to
Table 2), do as follows:
1 If the diameter of the related attach hole(s) in the upper pin (1)
is/are larger than the permitted diameter for the related attach
hole(s) in the aircraft structure (refer to Table 2), do as follows:
a Discard the upper pin (1).
b Go to step 2.B.(16) for the replacement of the upper pin (1).
2 If the diameter of the attach hole(s) in the upper pin (1) is/are
smaller than the related attach hole(s) in the aircraft structure
(refer to Table 2), do as follows:

### Page 24

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 23 of 97
Sep 29/2011
Revision D, Oct 22/2015
a Gradually drill or ream the related attach hole(s) of the upper pin
(1) until the diameter is/are a minimum of 0.015 in. (0.39 mm) less
than the specified hole dimension in Table 2
(refer to SRM 51−40−11).
CAUTION: BE CAREFUL WHEN YOU DRILL OR REAM THE
ATTACH HOLE(S) AS THE MATERIAL IS MADE
FROM HIGH STRENGTH STEEL.
b Make sure to use lubricant when you drill or ream the upper
pin (1) (refer to SRM 51−40−11).
c Use a reamer to remove the last minimum 0.015 in. (0.39 mm)
of material in the related attach hole(s) of the upper pin (1) to
get the specified hole dimension in Table 2
(refer to SRM 51−40−11).
NOTE: The use of a reamer is the only permitted tool to get the
last specified hole dimension.
CAUTION: BE CAREFUL WHEN YOU REAM THE ATTACH
HOLE(S) AS THE MATERIAL IS MADE FROM HIGH
STRENGTH STEEL.
d Make sure to use lubricant when you ream the upper pin (1)
(refer to SRM 51−40−11).
e Make sure that the edge distance for the attach holes in the
upper pin (1) are a minimum of 0.9D.
f If the edge distance for the attach hole(s) in the upper pin (1)
is/are less than 0.9D, speak with a representative of the
Bombardier Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
g Remove the burrs and sharp edges from the upper pin (1).
h Apply fluid resistant primer on the bare metal surfaces of the
upper pin (1) (refer to SRM 51−25−06).
i Do a detailed visual inspection of the upper pin (1) for
gouge(s), scratch(es), and corrosion
(refer to NDTM 51−20−09 PART 1).
j If gouge(s), and/or scratch(es) and/or corrosion is/are found,
do revision A or the latest approved revision of GREO
601R−27−42−008.

### Page 25

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 24 of 97
Sep 29/2011
Revision D, Oct 22/2015
k If the upper pin (1) cannot be repaired with revision A or the
latest approved revision of GREO 601R−27−42−008, go to
step 2.B.(16) for the replacement of the upper pin (1).
(d) If the upper pin (1) is repaired with revision A or the latest approved
revision of GREO 601R−27−42−008, or if no gouge(s), and/or
scratch(es), and/or corrosion is/are found, go to step 2.B.(24) to change
the identification and to add a serial number.
(16) To replace the upper pin (1) that has an oversized attach hole(s) (NCR condition) in
the aircraft structure of more than 0.195 in. (4.80 mm) and equal to or less than
0.286 in. (7.26 mm), do as follows:
(a) Replace an upper pin (1) where there is a NCR condition with upper pin
P/N K601R92308−55.
NOTE: The identification and the serialization procedure is not necessary
because the upper pin P/N K601R92308−55 is identified and
serialized.
(b) Align the upper pin (1) with the center hole of the aircraft structure and
attach temporarily.
(c) As necessary, make marks on the upper pin (1) to find the correct center
points of the aircraft structure attach holes.
(d) Remove the temporarily attached upper pin (1) from the aircraft
structure.
(e) Make sure that the edge distance for the attach holes in the upper pin
(1) are a minimum of 0.9D.
(f) If the edge distance for the attach hole(s) in the upper pin (1) are less
than 0.9D, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0)
or+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get
an approved disposition.
(g) Drill the center points of the attach holes in the upper pin (1) to a
diameter of .098 in. (2.49 mm) (refer to SRM 51−40−11).
CAUTION: BE CAREFUL WHEN YOU DRILL THE ATTACH HOLES AS
THE MATERIAL IS MADE FROM HIGH STRENGTH STEEL.
(h) Make sure to use lubricant when you drill or ream the upper pin (1) (refer
to SRM 51−40−11).

### Page 26

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 25 of 97
Sep 29/2011
Revision D, Oct 22/2015
(i) Gradually drill or ream the attach holes of the upper pin (1) until the
diameters are a minimum of 0.015 in. (0.39 mm) less than the specified
hole dimension in Table 2 (refer to SRM 51−40−11).
CAUTION: BE CAREFUL WHEN YOU REAM THE ATTACH HOLES AS
THE MATERIAL IS MADE FROM HIGH STRENGTH STEEL.
(j) Make sure to use lubricant when you drill or ream the upper pin (1) (refer
to SRM 51−40−11).
(k) Use a reamer to remove the last minimum 0.015 in. (0.39 mm) of
material in the attach holes of the upper pin (1) to get the last specified
hole dimension in Table 2. (refer to SRM 51−40−11).
NOTE: The use of a reamer is the only permitted tool to get the last
specified hole dimension.
CAUTION: BE CAREFUL WHEN YOU REAM THE ATTACH HOLES AS
THE MATERIAL IS MADE FROM HIGH STRENGTH STEEL.
(l) Make sure to use lubricant when you ream the upper pin (1) (refer to
SRM 51−40−11).
(m) Remove the burrs and sharp edges from the upper pin (1).
(n) Apply fluid resistant primer on the bare metal surfaces of the upper pin
(1) (refer to SRM 51−25−06).
(o) Record the serial number of the upper pin (1) in the applicable
logbooks.
Refer to Figure 1.
(17) Do a visual inspection of the four oversize (NCR condition) spacers (5) for
damage (refer to SRM 51−10−06 and to NDTM 51−20−09 PART 1).
(18) If damage to the oversize (NCR condition) spacer(s) (5) is/are found, replace
the spacer(s) (5) as follows:
(a) For a spacer bolt diameter of 0.205 to 0.221 in. (5.21 to 5.61 mm) replace
spacer (5) with P/N NAS42DD6−25 and do as follows:
1 Increase the diameter of the hole in the spacer(s) (5) to have a
maximum clearance of 0.010 in. (0.25 mm) with the related bolt (6)
diameter (refer to Table 7).
2 Remove burrs and sharp edges from the spacer(s) (5).

### Page 27

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 26 of 97
Sep 29/2011
Revision D, Oct 22/2015
3 Apply a chemical conversion coating on the bare metal surfaces of
the spacer(s) (5) (refer to SRM 51−21−11).
4 Apply one layer of fluid-resistant primer on the bare metal surfaces
of the spacer(s) (5) (refer to SRM 51−25−06).
(b) For a spacer bolt diameter of 0.250 to 0.281 in. (6.35 to 7.14 mm) replace
spacer (5) with P/N NAS42DD8−25 and do as follows:
1 Increase the diameter of the hole in the spacer(s) (5) to have a
maximum clearance of 0.010 in. (0.25 mm) with the related bolt (6)
diameter (refer to Table 7).
2 Remove burrs and sharp edges from the spacer(s) (5).
3 Apply a chemical conversion coating on the bare metal surfaces of
the spacer(s) (5) (refer to SRM 51−21−11).
4 Apply one layer of fluid-resistant primer on the bare metal surfaces
of the spacer(s) (5) (refer to SRM 51−25−06).
(19) For the lower pins (13), do the procedure that follows.
 NOTE: This procedure is applicable to the two lower pins (13). The procedure
that follows is written for only one lower pin (13).
(a) Clean the aircraft structure with solvent where the lower pin (13) is
attached (refer to SRM 51−26−00).
(b) Measure the diameter of the two attach holes in the aircraft structure.
TABLE 3 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND LOWER PIN
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE LOWER PIN
HOLE CONDITION NCR CONDITION
0.200 to 0.210 in.
(5.08 to 5.33 mm)
0.190 to 0.200 in.
(4.83 to 5.08 mm) Nominal No
0.215 to 0.225 in.
(5.46 to 5.72 mm)
0.205 to 0.215 in.
(5.21 to 5.46 mm) 1st oversize Yes
0.231 to 0.241 in.
(5.87 to 6.12 mm)
0.221 to 0.231 in.
(5.61 to 5.87 mm) 2nd oversize Yes
0.260 to 0.270 in.
(6.60 to 6.86 mm)
0.250 to 0.260 in.
(6.35 to 6.60 mm) Next size Yes

### Page 28

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 27 of 97
Sep 29/2011
Revision D, Oct 22/2015
TABLE 3 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND LOWER PIN
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE LOWER PIN
HOLE CONDITION NCR CONDITION
0.275 to 0.285 in.
(6.99 to 7.24 mm)
0.265 to 0.275 in.
(6.73 to 6.99 mm) 1st oversize Yes
0.291 to 0.301 in.
(7.39 to 7.65 mm)
0.281 to 0.291 in.
(7.14 to 7.39 mm) 2nd oversize Yes
(20) If the diameter of the attach hole(s) in the aircraft structure do not agree with the
diameters in Table 3, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get an
approved disposition.
(21) If the diameter of the attach hole(s) in the aircraft structure is/are a nominal
dimension of 0.200 to 0.210 in. (5.08 to 5.33 mm) (refer to Table 3), do as
follows:
(a) Measure the diameter of the attach holes in the lower pin (13).
(b) If the diameter of the attach hole(s) in the lower pin (13) is/are more than
0.200 in. (5.08 mm) (refer to Table 3), do as follows:
1 Discard the lower pin (13).
2 Get a lower pin (13) P/N 601R92309−3 or alternative.
NOTE: Lower pin P/N 600−92383−5 or 600−92383−7 or
601R92309−1 are permitted alternatives if P/N 601R92309−3
is not available.
NOTE: If the lower pin (13) is replaced with P/N 601R92309−3, the
identification and serialization procedure is not necessary
because the new part is identified and serialized.
(c) If the diameter of the attach holes in the lower pin (13) are a nominal
dimension of 0.190 to 0.200 in. (4.83 to 5.08 mm) (refer to Table 3), do
as follows:
1 Do a detailed visual inspection of the lower pin (13) for gouge(s),
scratch(es), and corrosion (refer to NDTM 51−20−09 PART 1).
2 If gouge(s), and/or scratch(es), and/or corrosion is/are found, do
revision A or the latest approved revision of GREO
601R−27−42−008.

### Page 29

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 28 of 97
Sep 29/2011
Revision D, Oct 22/2015
3 If the lower pin (13) cannot be repaired with revision A or the latest
approved revision of GREO 601R−27−42−008, do as follows:
a Discard the lower pin (13).
b Get a lower pin (13) P/N 601R92309−3 or alternative.
NOTE: Lower pin P/N 600−92383−5 or 600−92383−7 or
601R92309−1 are permitted alternatives if P/N
601R92309−3 is not available.
NOTE: If the lower pin (13) is replaced with lower pin P/N
601R92309−3, the identification and serialization
procedure is not necessary because the new part is
identified and serialized.
(d) If the lower pin (13) is replaced with P/N 601R92309−3, record the serial
number in the applicable logbooks.
(e) If the lower pin (13) is replaced with P/N 600−92383−5 or
600−92383−7 or 601R92309−1, go to step 2.B.(24) for the identification
and the serialization procedure.
(f) If the lower pin (13) is repaired with revision A or the latest approved
revision of GREO 601R−27−42−008, or if no gouge(s), and/or
scratch(es), and/or corrosion is/are found do as follows:
1 For the lower pin (13) P/N 600−92383−5, or 600−92383−7, or
601R92309−1, refer to step 2.B.(24) to change the identification and to
add a serial number.
2 For the lower pin (13) P/N 601R92309−3, the identification and
serialization procedure is not necessary because the pin is identified
and serialized.
(22) If the diameter of the attach hole(s) in the aircraft structure is/are an oversized
dimension of more than 0.215 in. (5.46 mm) and equal to or less than 0.301
in. (7.65 mm) (refer to Table 3), do as follows:
(a) Measure the diameter of the attach holes in the lower pin (13).
(b) If the diameter of the related attach holes in the lower pin (13) agree with
the diameter of the related attach holes in the aircraft structure (refer to
Table 3), do as follows:
1 Make sure that the edge distance for the attach holes in the lower
pin (13) are a minimum of 0.9D.

### Page 30

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 29 of 97
Sep 29/2011
Revision D, Oct 22/2015
2 If the edge distance for the attach holes in the lower pin (13) is/are less
than 0.9D, speak with a representative of the Bombardier Customer
Response Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get
an approved disposition.
3 Do a visual inspection of the lower pin (13) for gouge(s),
scratch(es), and corrosion (refer to NDTM 51−20−09 PART 1).
4 If gouge(s), and/or scratch(es) and/or corrosion is/are found, do
revision A or the latest approved revision of GREO
601R−27−42−008.
5 If the lower pin (13) cannot be repaired with revision A or the latest
approved revision of GREO 601R−27−42−008, go to step 2.B.(23)
for the replacement of the lower pin (13).
(c) If the diameter of the attach hole(s) in the lower pin (13) do not agree
with the diameter of the related attach hole(s) in the aircraft structure
(refer to Table 3), do as follows:
1 If the diameter of the attach hole(s) in the lower pin (13) is/are
larger than the related attach hole(s) in the aircraft structure (refer
to Table 3), do as follows:
a Discard the lower pin (13).
b Go to step 2 B (23) for the replacement of  the lower pin (13).
2 If the diameter of the attach hole(s) in the lower pin (13) is/are
smaller than the permitted diameter to the related attach hole(s) in
the aircraft structure (refer to Table 3), do as follows:
a Gradually drill or ream the related attach hole(s) of the lower
pin (13) until the diameter is/are a minimum of 0.015 in. (0.39
mm) less than the specified hole dimension in Table 3
(refer to SRM 51−40−11).
CAUTION: BE CAREFUL WHEN YOU DRILL OR REAM THE
ATTACH HOLE(S) AS THE MATERIAL IS MADE
FROM HIGH STRENGTH STEEL.
b Make sure to use lubricant when you drill or ream the lower
pin (13) (refer to SRM 51−40−11).
c Use a reamer to remove the last minimum 0.015 in. (0.39 mm)
of material in the related attach hole(s) of the lower pin (13) to
get the specified hole dimension in Table 3.
(refer to SRM 51−40−11).

### Page 31

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 30 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: The use of a reamer is the only permitted tool to get the
last specified hole dimension.
CAUTION: BE CAREFUL WHEN YOU REAM THE ATTACH
HOLE(S) AS THE MATERIAL IS MADE FROM HIGH
STRENGTH STEEL.
d Make sure to use lubricant when you ream the lower pin (13)
(refer to SRM 51−40−11).
e Make sure that the edge distance for the attach holes in the
lower pin (13) are a minimum of 0.9D.
f If the edge distance of the attach hole(s) in the lower pin (13)
is/are less than 0.9D, speak with a representative of the
Bombardier Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
g If necessary, do a countersink in the attach holes on the
outboard side of the lower pin (13) to get the correct
installation of the bolt (refer to SRM 51−41−02).
CAUTION: BE CAREFUL WHEN YOU DO A COUNTERSINK IN
THE ATTACH HOLE(S) AS THE MATERIAL IS
MADE FROM HIGH STRENGTH STEEL.
h Make sure to use lubricant when you countersink the lower
pin (13) (refer to SRM 51−40−11).
i Remove the burrs and sharp edges from the lower pin (13).
j Apply fluid resistant primer on the bare metal surfaces of the
lower pin (13) (refer to SRM 51−25−06).
k Do a detailed visual inspection of the lower pin (13) for
gouge(s), scratch(es), and corrosion
(refer to NDTM 51−20−09 PART 1).
l If gouge(s), and/or scratch(es) and/or corrosion is/are found,
do revision A or the latest approved revision of GREO
601R−27−42−008.
m If the lower pin (13) cannot be repaired with revision A or the
latest approved revision of GREO 601R−27−42−008, go to
step 2.B.(23) for the replacement.

### Page 32

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 31 of 97
Sep 29/2011
Revision D, Oct 22/2015
(d) If lower pin (13) is repaired with revision A or the latest approved revision
of GREO 601R−27−42−008, or if no gouge(s), and/or scratch(es),
and/or corrosion is/are found, go to step 2.B.(24) to change the
identification and to add a serial number.
(23) To replace the lower pin (13) that has an oversized attach hole(s) (NCR
condition) in the aircraft structure of more than 0.215 in. (5.46 mm) and equal
to or less than 0.301 in. (7.65 mm) (refer to Table 3), do as follows:
(a) Replace a lower pin (13) where there is a NCR condition with P/N
K601R92308−53.
NOTE: The identification and serialization procedure is not necessary
because the lower pin P/N K601R92308−53 is identified and
serialized.
(b) Align the lower pin (13) with the center hole of the aircraft structure and
attach temporarily.
(c) As necessary, make marks on the lower pin (13) to find the correct
center points of the aircraft structure attach holes.
(d) Remove the temporarily attached lower pin (13) from the aircraft
structure.
(e) Make sure that the edge distance for the two attach holes in the lower
pin (13) are a minimum of 0.9D.
(f) If the edge distance for the attach hole(s) in the lower pin (13) are less than
0.9D, speak with a representative of the Bombardier Customer Response
Center at +1−844−272−2720 (1−844−CRC−CRC0) or
+1−514−855−8500 or e-mail at thd.crj@aero.bombardier.com to get an
approved disposition.
(g) Drill the center points of the two attach holes in the lower pin (13) to a
diameter of .098 in. (2.49 mm) (refer to SRM 51−40−11).
CAUTION: BE CAREFUL WHEN YOU DRILL THE ATTACH HOLES AS
THE MATERIAL IS MADE FROM HIGH STRENGTH STEEL.
(h) Make sure to use lubricant when you drill or ream the lower pin (13)
(refer to SRM 51−40−11).
(i) Gradually drill or ream the two attach holes of the lower pin (13) until the
diameters are a minimum of 0.015 in. (0.39 mm) less than the specified
hole dimensions in Table 3 (refer to SRM 51−40−11).

### Page 33

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 32 of 97
Sep 29/2011
Revision D, Oct 22/2015
CAUTION: BE CAREFUL WHEN YOU DRILL OR REAM THE ATTACH
HOLES AS THE MATERIAL IS MADE FROM HIGH STRENGTH
STEEL.
(j) Make sure to use lubricant when you drill or ream the lower pin (13)
(refer to SRM 51−40−11).
(k) Use a reamer to remove the last minimum 0.015 in. (0.39 mm) of
material in the attach holes of the lower pin (13) to get the last specified
hole dimension in Table 3. (refer to SRM 51−40−11).
NOTE: The use of a reamer is the only permitted tool to get the last
specified hole dimension.
CAUTION: BE CAREFUL WHEN YOU REAM THE ATTACH HOLES AS
THE MATERIAL IS MADE FROM HIGH STRENGTH STEEL.
(l) Make sure to use lubricant when you ream the lower pin (13) (refer to
SRM 51−40−11).
(m) Do a countersink in the attach holes on the outboard side of the lower
pin (13) to get the correct installation of the bolt (14)
(refer to SRM 51−41−02).
CAUTION: BE CAREFUL WHEN YOU DO A COUNTERSINK IN THE
ATTACH HOLES AS THE MATERIAL IS MADE FROM HIGH
STRENGTH STEEL.
(n) Make sure to use lubricant when you countersink the lower pin (13)
(refer to SRM 51−40−11).
(o) Remove the burrs and sharp edges from the lower pin (13).
(p) Apply fluid resistant primer on the bare metal surfaces of the lower pin
(13). (refer to SRM 51−25−06).
(q) Record the serial number of the lower pin (13) in the applicable
logbooks.
Refer to Figure 3.
(24) Change the identification of the trunnions (9), the upper pins (1) and the lower
pins (13) that are not damaged and add a serial number as follows:
 NOTE: It is permitted to use this step to change the identification of the spare
parts.
 NOTE: If trunnions P/N 601R92386−3, or P/N K601R92308−51, lower pins P/N
601R92309−3 or P/N K601R92308−53, and upper pins P/N
601R92310−3 or P/N K601R92308−55 are used to replace the
defective parts, it is not necessary to do this step.

### Page 34

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 33 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART
NAME
PART NUMBER
(PRE-MOD)
PART NUMBER
WITHOUT NCR
CONDITION
(POST -MOD)
PART NUMBER
WITH NCR
CONDITION
(POST -MOD)
SERVICE SERIAL 
NUMBER
Upper pin 600−92384−5 K601R92308−5 K601R92308−35 orK601R92308−55 /C0019 SS/N RJ/XXXYYYYY /C0004
Upper pin 600−92384−7 K601R92308−7 K601R92308−35 orK601R92308−55 /C0019 SS/N RJ/XXXYYYYY /C0004
Upper pin 601R92310−1 /C0006 K601R92308−9 K601R92308−35 orK601R92308−55 /C0019 SS/N RJ/XXXYYYYY /C0004
Upper pin 601R92310−3 601R92310−3 K601R92308−35 orK601R92308−55 /C0019 SS/N RJ/XXXYYYYY /C0004
Lower pin 600−92383−5 K601R92308−11 K601R92308−33 orK601R92308−53 /C0019 SS/N RJ/XXXYYYYY /C0004
Lower pin 600−92383−7 K601R92308−13 K601R92308−33 orK601R92308−53 /C0019 SS/N RJ/XXXYYYYY /C0004
Lower pin 601R92309−1 /C0006 K601R92308−15 K601R92308−33 orK601R92308−53 /C0019 SS/N RJ/XXXYYYYY /C0004
Lower pin 601R92309−3 601R92309−3 K601R92308−33 orK601R92308−53 /C0019 SS/N RJ/XXXYYYYY /C0004
Trunnion 601R92386−1 K601R92308−19 K601R92308−31 orK601R92308−51 /C0019 SS/N RJ/XXXYYYYY /C0004
Trunnion 601R92386−3 601R92386−3 K601R92308−31 orK601R92308−51 /C0019 SS/N RJ/XXXYYYYY /C0004
Trunnion NCR# xxxxxx−x /C0001 − K601R92308−31 orK601R92308−51 /C0019 SS/N RJ/XXXYYYYY /C0004
Lower Pin NCR# xxxxxx−x /C0001 − K601R92308−33 orK601R92308−53 /C0019 SS/N RJ/XXXYYYYY /C0004
Upper pin NCR# xxxxxx−x /C0001 − K601R92308−35 orK601R92308−55 /C0019 SS/N RJ/XXXYYYYY /C0004
/C0001 Can be any numerical and/or letter combination which identifies a Non-Conformance Part (NCR)
/C0019 P/N K601R92308−51, P/N K601R92308−53, and P/N K601R92308−55 are replacement parts for a
NCR condition.
/C0004 XXX, is for the three-letter airline designator code that the International Civil 
    Aviation Organization (ICAO) gave to the airline.
    YYYYY , is for the five-digit sequence number that the operator chose.
/C0006 Upper pin P/N 601R92310−1PP is an alternative to P/N 601R92310−1 and lower pin P/N
601R92309−1PP is an alternative to P/N 601R92309−1.

### Page 35

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 34 of 97
Sep 29/2011
Revision D, Oct 22/2015
(a) If the ICAO airline designator code is not available, write the serial
number as follows:
SS/N RJ/BA(aircraft serial number)−1 or subsequent number.
When the identification of the serial number is done on a spare part, the
aircraft serial number of one of the aircraft of the fleet and a subsequent
number is used.
Example:
AIRCRAFT
SERIAL
NUMBER
PART NUMBER SERVICE SERIALNUMBER
8999 K601R92308−9 SS/N RJ/BA8999−1
8999 K601R92308−9 SS/N RJ/BA8999−2
7900 K601R92308−15 SS/N RJ/BA7900−1
7901 K601R92308−15 SS/N RJ/BA7901−1
Spare K601R92308−19 SS/N RJ/BA7901−2
7821 K601R92308−19 SS/N RJ/BA7821−1
7500 K601R92308−35 SS/N RJ/BA7500−1
(b) Prepare the surface for identification of the upper pins (1), the lower pins
(13), and the trunnions (9) as follows:
1 If necessary, remove the initial identification.
2 Lightly rub the surface of the identification area with a Scotch Brite
pad or alternative, and make sure not to remove the paint.
3 Clean the area with a solvent cleaner
(refer to AMM 51−26−00−110−801).
(c) With indelible ink or an adhesive label, change the identification of the
upper pins (1), the lower pins (13), and the trunnions (9) as follows:
1 If adhesive labels are used, cut the edge of the adhesive labels as
necessary to get a correct fit with the surface of the parts.
2 Write the part number and the serial number on the upper pins (1)
at approximately 0.52 in. (13.2 mm) and at approximately 0.10 in.
(2.5 mm) from the edges of the upper pin (1) (refer to Figure 3).

### Page 36

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 35 of 97
Sep 29/2011
Revision D, Oct 22/2015
3 Write the part number and the serial number on the lower pins (13)
at approximately 0.52 in. (13.2 mm) and at approximately 0.13 in.
(3.3 mm) from the edges of the lower pin (13) (refer to Figure 3).
4 Write the part number and the serial number on the trunnions (9) at
one of the two locations that follows:
−At approximately 0.66 in. (16.8 mm) and at approximately 0.04
   in. (1.1 mm) from the edges of the trunnion (9)
   (refer to Figure 3).
OR
−At two places (one location for the serial number and one
   location for the identification) approximately 0.40 in. from the
   attaching holes of the trunnion (9) and at approximately 0.05 in.
   from the edge of the trunnion (9) (refer to Figure 3).
(d) Apply a layer of clear polyurethane topcoat on the identification and the
serial number of the upper pins (1), the lower pins (13), and the
trunnions (9) (refer to SRM 51−25−16).
NOTE: For the installation of the adhesive labels, the clear polyurethane
topcoat must be applied 0.25 in. (6.4 mm) more than the size of
the adhesive labels.
(e) Make sure that you can read the identification and the serial number.
(25) Record the serial number of the trunnions (9), the upper pins (1) and the lower
pins (13) in the applicable logbooks.
NOTE: To find the history of the part at the time of serialization refer to ATA
Report 51−93−01 /quoteblleftStructural Maintenance Program Guidelines For
Continuing Airworthiness" paragraph 4.6, /quoteblleftRemovable Structural
Components". If a part has been mixed between aircraft certified at
51,000 lb MTOW and 53,000 lb MTOW, the intervals applicable to
53,000 lb MTOW must apply to the part.
Refer to Figure 1 and/or 2.
(26) Use AMM 27−42−01−400−801 with the steps that follow to install the
HSTA (20), the trunnions (9), the upper pins (1), and the lower pins (13)
with the bolts (6), (7), (14), (15), (19), the new laminated shim (8), the
washers (4), (10), (16), the spacers (5), the nuts (3), (11), (17), and the
cotter pins (2), (12), (18).
(a) Drill the holes of the new laminated shim(s) (8) to agree with the
dimensions of the bolts (7), (15) and (19) (refer to Table 4).

### Page 37

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 36 of 97
Sep 29/2011
Revision D, Oct 22/2015
(b) Remove the burrs and the sharp edges from the new laminated shim(s) (8).
(c) If the new laminated shim(s) (8) was/were peeled, apply a layer of
fluid-resistant primer on the bare metal surfaces of the laminated shims (8)
(refer to SRM 51−25−06).
(d) Make sure that the nuts (11), and the cotter pins (12) that are used to install
the trunnions (9) and the HSTA (20) are new.
(e) If necessary, do a countersink to the attach holes of the lower pin (13) to get
the correct installation of the bolt(s) (14) (refer to SRM 51−41−02).
(f) Make sure to use lubricant when you countersink the lower pin (13)
(refer to SRM 51−40−11).
(g) If necessary, apply fluid resistant primer on the bare metal surfaces of the
lower pin (13). (refer to SRM 51−25−06).
(h) Make sure that the nuts (3) and the cotter pins (2) that are used to attach the
upper pins (1) and the HSTA (20) are new.
(i) Make sure that the nuts (17) and the cotter pins (18) that are used to attach
the lower pins (13) and the HSTA (20) are new.
(j) Before the installation of the bolts (7), (15), (19), the washers (10), and the
nuts (11), make sure that the hardware agrees with the hole dimensions of
the aircraft structure and trunnion (9) (refer to Table 4).
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N NAS1149F0632P with washer P/N NAS1149F0616P, or to
add washer P/N NAS1149F0616P to washer P/N NAS1149F0632P.
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N B0202013S2520−32 with washer P/N
B0202013S2520−16, or to add washer P/N B0202013S2520−16 to
washer P/N B0202013S2520−32.
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N B0202013S2620−32 with washer P/N
B0202013S2620−16, or to add washer P/N B0202013S2620−16 to
washer P/N B0202013S2620−32.
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N NAS1149F0732P with washer P/N NAS1149F0716P, or to
add washer P/N NAS1149F0716P to washer P/N NAS1149F0732P.
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N B0202013S2924−32 with washer P/N
B0202013S2924−16, or to add washer P/N B0202013S2924−16 to
washer P/N B0202013S2924−32.

### Page 38

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 37 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N B0202013S3024−32 with washer P/N
B0202013S3024−16, or to add washer P/N B0202013S3024−16 to
washer P/N B0202013S3024−32.
NOTE: To prevent over-torque of the nuts (11), it is permitted to replace the
washer P/N with washer P/N NAS1149F0816P, or to add washer P/N
NAS1149F0816P to washer P/N NAS1149F0832P.
TABLE 4 − AIRCRAFT STRUCTURE AND TRUNNION − HOLE-DIMENSION/HARDWARE
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE TRUNNION
BOLT
DIAMETER
BOLT
P/N
NUT P/N
WASHER P/N
0.375 to 0.380 in.
(9.53 to 9.65 mm)
0.375 to 0.380 in.
(9.53 to 9.65 mm)
0.375 in
(9.53 mm) NAS6206−( )D
MS17826−6
NAS1149F0616P
and/or
NAS1149F0632P
0.391 to 0.396 in
(9.93 to 10.06 mm)
0.391 to 0.396 in
(9.93 to 10.06 mm)
0.390 in
(9.91 mm) NAS6206−( )DX
MS17826−6
B0202013S2520−16
and/or
B0202013S2520−32
0.406 to 0.411 in
(10.31 to 10.44 mm)
0.406 to 0.411 in
(10.31 to 10.44 mm)
0.406 in
(10.31 mm) NAS6206−( )DY
MS17826−6
B0202013S2620−16
and/or
B0202013S2620−32
0.438 to 0.443 in
(11.13 to 11.25 mm)
0.438 to 0.443 in
(11.13 to 11.25 mm)
0.437 in
(11.10 mm) NAS6207−( )D
MS17826−7
NAS1149F0716P
and/or
NAS1149F0732P
0.453 to 0.458 in
(11.51 to 11.63 mm)
0.453 to 0.458 in
(11.51 to 11.63 mm)
0.453 in
(11.51 mm) NAS6207−( )DX
MS17826−7
B0202013S2924−16
and/or
B0202013S2924−32
0.469 to 0.474 in
(11.91 to 12.04 mm)
0.469 to 0.474 in
(11.91 to 12.04 mm)
0.468 in
(11.89 mm) NAS6207−( )DY
MS17826−7
B0202013S3024−16
and/or
B0202013S3024−32

### Page 39

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 38 of 97
Sep 29/2011
Revision D, Oct 22/2015
TABLE 4 − AIRCRAFT STRUCTURE AND TRUNNION − HOLE-DIMENSION/HARDWARE
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE TRUNNION
BOLT
DIAMETER
BOLT
P/N
NUT P/N
WASHER P/N
0.500 to 0.505 in
(12.70 to 12.83 mm)
0.500 to 0.505 in
(12.70 to 12.83 mm)
0.500 in
(12.70 mm) NAS6208−( )D
MS17826−8
NAS1149F0816P
and/or
NAS1149F0832P
(k) Before the installation of the trunnions (9), make sure that the bolt(s)
(7), (15), and (19) that have an oversize diameter of 0.390 in. (9.91
mm) or more have the correct P/N (refer to Table 5 ).
TABLE 5 − TRUNNION − OVERSIZE BOLT DIAMETERS AND P/N’s
UPPER TRUNNION LOWER TRUNNION
BOLT
DIAMETER BOLT P/N BOLT P/N
0.390 in
(9.91 mm)
1st oversize
NAS6206−14DX
and
NAS6206−20DX
NAS6206−8DX
0.406 in
(10.31 mm)
2nd oversize
NAS6206−14DY
and
NAS6206−20DY
NAS6206−8DY
0.437 in
(11.10 mm)
Next size
NAS6207−14D
and
NAS6207−20D
NAS6207−8D
0.453 in
(11.51 mm)
1st oversize
NAS6207−14DX
and
NAS6207−20DX
NAS6207−8DX
0.468 in
(11.89 mm)
2nd oversize
NAS6207−14DY
and
NAS6207−20DY
NAS6207−8DY
0.500 in
(12.70 mm)
Next size
NAS6208−14D
and
NAS6208−20D
NAS6208−8D

### Page 40

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 39 of 97
Sep 29/2011
Revision D, Oct 22/2015
(l) Before the installation of the bolts (6), the washers (4), and the nuts (3), make
sure that the hardware agrees with the hole dimensions of the aircraft
structure and the upper pins (1) (refer to Table 6).
TABLE 6 − AIRCRAFT STRUCTURE AND UPPER PIN − HOLE-DIMENSION/HARDWARE
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF
THE ATTACH
HOLES IN
THE UPPER PIN
BOLT
DIAMETER
BOLT
P/N
NUT P/N
WASHER P/N
0.189 to 0.195 in.
(4.80 to 4.95 mm)
0.215 to 0.225 in.
(5.46 to 5.72 mm)
0.189 in.
(4.80 mm) NAS1203−13D MS17826−3NAS1149F0332P
0.205 to 0.210 in.
(5.21 to 5.33 mm)
0.225 to 0.235 in.
(5.72 to 5.97 mm)
0.205 in.
(5.21 mm) NAS1580A3R13DX MS17826−3B0202013S1516−32
0.221 to 0.226 in.
(5.61 to 5.74 mm)
0.239 to 0.249 in.
(6.07 to 6.32 mm)
0.221 in.
(5.61 mm) NAS1580A3R13DY
MS17826−3
B0202013S1516−32
0.250 to 0.255 in.
(6.35 to 6.48 mm)
0.270 to 0.280 in.
(6.86 to 7.11 mm)
0.250 in.
(6.35 mm) NAS1204−13D
MS17826−4
NAS1149F0432P
0.265 to 0.270 in.
(6.73 to 6.86 mm)
0.284 to 0.294 in.
(7.21 to 7.47 mm)
0.265 in.
(6.73 mm) NAS1580A4R13DX MS17826−4B0202013S1716−32
0.281 to 0.286 in.
(7.14 to 7.26 mm)
0.299 to 0.309 in.
(7.59 to 7.85 mm)
0.281 in.
(7.14 mm) NAS1580A4R13DY
MS17826−4
B0202013S1816−32
(m) Before the installation of the upper pins (1), make sure that the bolt(s) (6)
that have an oversize diameter of 0.205 in. (5.21 mm) or more have the
correct P/N (refer to Table 7).
TABLE 7
UPPER PIN − OVERSIZE BOLT DIAMETERS
AND P/N’s
UPPER PIN
BOLT
DIAMETER BOLT P/N
0.205 in.
(5.21 mm)
1st oversize
NAS1580A3R13DX
0.221 in.
(5.61 mm)
2nd oversize
NAS1580A3R13DY

### Page 41

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 40 of 97
Sep 29/2011
Revision D, Oct 22/2015
TABLE 7
UPPER PIN − OVERSIZE BOLT DIAMETERS
AND P/N’s
UPPER PIN
BOLT
DIAMETER BOLT P/N
0.250 in.
(6.35 mm)
Next size
NAS1204−13D
0.265 in.
(6.73 mm)
1st oversize
NAS1580A4R13DX
0.281 in.
(7.14 mm)
2nd oversize
NAS1580A4R13DY
(n) Before the installation of the bolts (14), the washers (16), and the nuts
(17), make sure that the hardware agrees with the hole dimensions of
the aircraft structure and the lower pins (13) (refer to Table 8).
TABLE 8 − AIRCRAFT STRUCTURE AND LOWER PIN − HOLE-DIMENSION/HARDWARE
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF
THE ATTACH
HOLES IN
THE LOWER PIN
BOLT
DIAMETER
BOLT
P/N
NUT P/N
WASHER P/N
0.200 to 0.210 in.
(5.08 to 5.33 mm)
0.190 to 0.200 in.
(4.83 to 5.08 mm)
0.189 in.
(4.80 mm) NAS1203−8D
MS17826−3
NAS1149F0332P
0.215 to 0.225 in.
(5.46 to 5.72 mm)
0.205 to 0.215 in.
(5.21 to 5.46 mm)
0.205 in.
(5.21 mm) NAS1580A3R8DX MS17826−3B0202013S1516−32
0.231 to 0.241 in.
(5.87 to 6.12 mm)
0.221 to 0.231 in.
(5.61 to 5.87 mm)
0.221 in.
(5.61 mm) NAS1580A3R8DY MS17826−3B0202013S1516−32
0.260 to 0.270 in.
(6.60 to 6.86 mm)
0.250 to 0.260 in.
(6.35 to 6.60 mm)
0.250 in.
(6.35 mm) NAS8604D8 MS17826−4NAS1149F0432P
0.275 to 0.285 in.
(6.99 to 7.24 mm)
0.265 to 0.275 in.
(6.73 to 6.99 mm)
0.265 in.
(6.73 mm) NAS8604D8X
MS17826−4
B0202013S1716−32
0.291 to 0.301 in.
(7.39 to 7.65 mm)
0.281 to 0.291 in.
(7.14 to 7.39 mm)
0.281 in.
(7.14 mm) NAS8604D8Y
MS17826−4
B0202013S1816−32

### Page 42

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 41 of 97
Sep 29/2011
Revision D, Oct 22/2015
(o) Before the installation of the lower pins (13), make sure that the bolt(s) (14)
that have an oversize diameter of 0.205 in. (5.21 mm) or more have the
correct P/N (refer to Table 9).
TABLE 9
LOWER PIN − OVERSIZE BOLT DIAMETERS
AND P/N’s
LOWER PIN
BOLT
DIAMETER BOLT P/N
0.205 in.
(5.21 mm)
1st oversize
NAS1580A3R8DX
0.221 in.
(5.61 mm)
2nd oversize
NAS1580A3R8DY
0.250 in.
(6.35 mm)
Next size
NAS8604D8
0.265 in.
(6.73 mm)
1st oversize
NAS8604D8X
0.281 in.
(7.14 mm)
2nd oversize
NAS8604D8Y
(p) Torque the installed fasteners (refer to AMM 20−21−00−910−801).

### Page 43

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 42 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − NCR Condition − Removal/Installation
Figure 1 (Sheet 1 of 4)
rsb601r27160_003, kp, Feb. 6, 2015
1
LEGEND
  1. Upper pin.
  2. Cotter pin.
  3. Nut.
  4. Washer.
  5. Spacer.
  6. Bolt.
  7. Bolt.
  8. Laminated shim.
  9. Trunnion.
10. Washer.
11. Nut.
12. Cotter pin.
13. Lower pin.
14. Bolt.
15. Bolt.
16. Washer.
17. Nut.
18. Cotter pin.
19. Bolt.
20. HSTA.
NOTES
      To prevent over−torque, it is
      permissible to replace a
      0.032 in. (0.81 mm) thick washer
      with a 0.016 in. (0.41 mm) thick
      washer, or to add a 0.016 in.
      (0.41 mm) thick washer to a
      0.032 in. (0.81 mm) thick washer.
2.   For part number, refer to table A.
1
7
12
11
10
9
8
9
12
11
10
8
9
13
18
1716
1314
15
AIRCRAFT
STRUCTURE
(REF)
AIRCRAFT
STRUCTURE (REF)
1
19
5
1
3
2
4
20
6
A
A

### Page 44

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 43 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − NCR Condition − Removal/Installation
Figure 1 (Sheet 2 of 4)
rsb601r27160_004, kp, Feb. 6, 2015
K601R92308−35
K601R92308−55
NCR #xxxxxx−x
P/NNAME
Upper pin
(Pre−Mod)
Nut
Washer
Spacer
ITEM
1
2
4
5
6
7
8
9
ALTERNATE PART
(Post−Mod)
Cotter pin MS24665−153
MS17826−3
B0202013S1516−32
NAS1149F0432P
B0202013S1716−32
B0202013S1816−32
B0202013−1816−32
MS17826−4
B0202013A1516−32
B0202013−1516−32
B0202013A1716−32
B0202013−1716−32
B0202013A1816−32
(Post−Mod)
3 (Post−Mod)
(Post−Mod)
NAS42DD6−25N
NAS42DD8−25N(Post−Mod)
Bolt
NAS1580A3R13DX
NAS1580AR13DY
NAS1204−13D
NAS1580A4R13DX
NAS1580A4R13DY
(Post−Mod)
NAS6206−14DX
NAS6206−14DY
NAS6207−14DX
NAS6207−14DY
NAS6207−14D
NAS6208−14D
(Post−Mod)
Laminated shim 601R92303−17(Post−Mod)
Trunnion K601R92308−31
NCR #xxxxxx−x(Pre−Mod)
(Post−Mod) K601R92308−51
TABLE A
Bolt

### Page 45

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 44 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − NCR Condition − Removal/Installation
Figure 1 (Sheet 3 of 4)
rsb601r27160_005, kp, Feb. 6, 2015
11
P/NNAME
Nut
ITEM ALTERNATE PART
MS17826−6
MS17826−7(Post−Mod)
TABLE A
10 Washer
B0202013S2520−16
B0202013A2520−16
B0202013−2520−16
B0202013S2520−32
B0202013A2520−32
B0202013−2520−32
B0202013S2620−16
B0202013A2620−16
B0202013−2620−16
B0202013S2620−32
B0202013A2620−32
B0202013−2620−32
B0202013S2924−16
B0202013A2924−16
B0202013−2924−16
B0202013S2924−32
B0202013A2924−32
B0202013−2924−32
B0202013S3024−16
B0202013A3024−16
B0202013−3024−16
B0202013S3024−32
B0202013A3024−32
B0202013−3024−32
NAS1149F0716P
NAS1149F0732P
NAS1149F0816P
NAS1149F0832P
(Post−Mod)
MS17826−8
12 Cotter pin (Post−Mod) MS24665−300
Lower pin13
(Post−Mod)
(Pre−Mod) NCR #xxxxxx−x
 K601R92308−33
K601R92308−53
Bolt14 (Post−Mod)
NAS1580A3R8DX
NAS1580A3R8DY
NAS8604D8X
NAS8604D8Y
NAS8604D8

### Page 46

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 45 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − NCR Condition − Removal/Installation
Figure 1 (Sheet 4 of 4)
rsb601r27160_006, kp, Feb. 6, 2015
P/NNAMEITEM ALTERNATE PART
TABLE A
Nut
Washer
18
16
Cotter pin MS24665−153
MS17826−3
B0202013S1516−32
NAS1149F0432P
B0202013S1716−32
B0202013S1816−32
B0202013−1816−32
MS17826−4
B0202013A1516−32
B0202013−1516−32
B0202013A1716−32
B0202013−1716−32
B0202013A1816−32
(Post−Mod)
17 (Post−Mod)
(Post−Mod)
Bolt15 (Post−Mod)
NAS6206−8DX
NAS6206−8DY
NAS6207−8D
NAS6207−8DX
NAS6207−8DY
NAS6208−8D
Bolt19 (Post−Mod)
NAS6206−20DX
NAS6206−20DY
NAS6207−20DX
NAS6207−20DY
NAS6207−20D
NAS6208−20D

### Page 47

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 46 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − Nominal Condition − Removal/Installation
Figure 2 (Sheet 1 of 3)
rsb601r27160_003, kp, Feb. 6, 2015
1
LEGEND
  1. Upper pin.
  2. Cotter pin.
  3. Nut.
  4. Washer.
  5. Spacer.
  6. Bolt.
  7. Bolt.
  8. Laminated shim.
  9. Trunnion.
10. Washer.
11. Nut.
12. Cotter pin.
13. Lower pin.
14. Bolt.
15. Bolt.
16. Washer.
17. Nut.
18. Cotter pin.
19. Bolt.
20. HSTA.
NOTES
      To prevent over−torque, it is
      permissible to replace a
      0.032 in. (0.81 mm) thick washer
      with a 0.016 in. (0.41 mm) thick
      washer, or to add a 0.016 in.
      (0.41 mm) thick washer to a
      0.032 in. (0.81 mm) thick washer.
2.   For part number, refer to table B.
1
7
12
11
10
9
8
9
12
11
10
8
9
13
18
1716
1314
15
AIRCRAFT
STRUCTURE
(REF)
AIRCRAFT
STRUCTURE (REF)
1
19
5
1
3
2
4
20
6
A
A

### Page 48

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 47 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − Nominal Condition − Removal/Installation
Figure 2 (sheet 2 of 3)
rsb601r27160_007, kp, Feb. 9, 2015
600−92384−5
K601R92308−5
601R92310−3
600−92384−7
K601R92308−7
601R92310−3
601R92310−1
K601R92308−9
601R92310−3
MS24665−134
MS24665−153
MS17826−3
NAS6206−14D
601R92303−17
601R92386−1
K601R92308−19
AN960−616L
NAS1149F0632P
MS17826−6
MS24665−134
MS24665−283
MS24665−300
601R92386−3
P/NNAME
Upper pin
(Pre−Mod)
Nut
Washer
ITEM
1
2
7
8
9
(Post−Mod)
Cotter pin
3
Laminated shim
Trunnion
TABLE B
Bolt
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
10 (Pre−Mod)
(Post−Mod)
Nut11
12 Cotter pin
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
601R92310−3
(Pre−Mod)
S8225−06−14D
(Post−Mod) NAS6206−14D
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
(Pre−Mod)
(Post−Mod)
601R92386−3

### Page 49

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 48 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − Nominal Condition − Removal/Installation
Figure 2 (Sheet 3 of 3)
601R92309−1
601R92309−3
NAS6206−8D
MS24665−134
MS24665−153
NAS6206−20D
K601R92308−15
Lower pin
600−92383−5
K601R92308−11
600−92383−7
K601R92308−13
P/NNAMEITEM
TABLE B
13
(Pre−Mod)
(Post−Mod)
601R92309−3
(Pre−Mod)
(Post−Mod)
601R92309−3
(Pre−Mod)
(Post−Mod)
15 Bolt
18 Cotter pin (Pre−Mod)
(Post−Mod)
19 Bolt
(Pre−Mod)
(Post−Mod) 601R92309−3
(Pre−Mod)
(Post−Mod)
S8225−06−8D
NAS6206−8D
NAS6206−20D
S8225−06−20D
(Pre−Mod)
(Post−Mod)
rsb601r27160_008, kp, Feb. 9, 2015

### Page 50

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 49 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART A − HSTA Pins and Trunnions − Identification and Serialization
Figure 3 (Sheet 1 of 1)
A
rsb601r27160_002, kp, Feb. 10, 2015
NOTES
For Upper pin P/N 601R92310−3 and
K601R92308−55, the identification and
serialization procedure is not necessary.
For Trunnion P/N 601R92386−3 and K601R92308−51,
the identification and serialization procedure is not necessary.
It is permissible to divide the identification between the sides.
For Lower pin P/N 601R92309−3 and
K601R92308−53, the identification and
serialization procedure is not necessary.
1. XXX is for the three−letter airline designator that
the International Civil Aviation Organization (ICAO)
gave to the airline.
The Accomplishment Instructions gives an alternate
for the operators that do not have an ICAO code.
YYYYY is the five−digit sequence number
that the operator selected and recorded.
The letter Z shown in the part number is
replaced with the applicable dash number
listed in the legend for the upper pin (1)
and the lower pin (13).
The dimensions are approximate
and shown as reference only.
The identification of the trunnion (9) is
done with View A or B.
2
3
4
5
6
7
LEGEND
1.  Upper pin
     600−92384−5 (Pre−Mod)
     K601R92308−5 (Post−Mod), or
     600−92384−7 (Pre−Mod)
     K601R92308−7 (Post−Mod), or
     601R92310−1 (Pre−Mod)
     K601R92308−9 (Post−Mod), or
9.  Trunnion
     601R92386−1 (Pre−Mod)
     K601R92308−19 (Post−Mod), or
13.Lower pin
     600−92383−5 (Pre−Mod)
     K601R92308−11 (Post−Mod), or
     600−92383−7 (Pre−Mod)
     K601R92308−13 (Post−Mod), or
     601R92309−1 (Pre−Mod)
     K601R92308−15 (Post−Mod), or
     NCR #xxxxxx−x (Pre−Mod)
     K601R92308−35 (Post−Mod).
     NCR #xxxxxx−x (Pre−Mod)
     K601R92308−31 (Post−Mod).
     NCR #xxxxxx−x (Pre−Mod)
     K601R92308−33 (Post−Mod).
0.40 in
(10.2 mm)
0.05 in
(1.3 mm)
0.05 in
(1.3 mm)0.40 in
(10.2 mm)
4 6 5
2 6
5
5
5
5
53
0.52 in.
(13.2 mm)
0.13 in.
(3.3 mm)
13
0.52 in.
(13.2 mm)
1
0.10 in.
(2.5 mm)
0.66 in.
(16.8 mm)
9 0.04 in.(1.1 mm)
5
5
5
5
B
B
7
7

### Page 51

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 50 of 97
Sep 29/2011
Revision D, Oct 22/2015
C. Job Close-Out
NOTE: The steps in the Job Close-Out section of this service bulletin, except for
the return-to-service tests, are recommended steps. The steps give a
recommendation to install components removed during the Job Set-Up.
This recommendation is to make sure that the aircraft is safe and ready
to return to service. Alternative steps can be used at the operator
discretion.
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Install the access panels that follow:
ACCESS DESIGNATION REFERENCE
Middle Upper
Fairing
Access panel AMM 55−32−05−400−806
Middle Lower 
Fairing
Access panel AMM 55−32−05−400−807
(3) Apply external AC power to the aircraft (Refer to AMM 12−00−07−861−801).
(4) Do the operational test of the HSTA trim system
(AMM 27−40−00−710−802).
(5) Do the functional test of the HSTCU (AMM 27−41−00−740−801).
(6) Remove the applicable warning placards from the pilot’s and the copilot’s
control wheels and the STAB TRIM/MACH TRIM panel.
(7) When PART A of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleftService Bulletin 601R−27−160, Revision D, Flight
Controls − Horizontal Stabilizer Trim Actuator (HSTA) − Serialization of the
HSTA Pins and Trunnions, PART A, incorporated."

### Page 52

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 51 of 97
Sep 29/2011
Revision D, Oct 22/2015
PART B − Inspection of the Attach Holes of the HSTA Pins and Trunnions
Reference Information
REFERENCE DESIGNATION
AMM 12−00−07−861−801 Connect External AC Power
AMM 20−21−00−910−801 Torque procedures for Threaded Fasteners
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 27−40−00−710−802 Operational Test of the Horizontal Stabilizer Trim
System
AMM 27−41−00−740−801 Functional Check (Ground Maintenance Test) of
the HSTCU
AMM 27−42−01−000−801 Removal of the Horizontal-Stabilizer Trim 
Actuator (HSTA)
AMM 27−42−01−400−801 Installation of the Horizontal-Stabilizer Trim 
Actuator (HSTA)
AMM 51−26−00−110−801 Solvent Cleaning
AMM 55−32−05−000−806 Removal of the Middle Upper Fairing
AMM 55−32−05−400−806 Installation of the Middle Upper Fairing
AMM 55−32−05−000−807 Removal of the Middle Lower Fairing
AMM 55−32−05−400−807 Installation of the Middle Lower Fairing
SRM 51−10−06 Damage
SRM 51−21−11 Corrosion Prevention Procedures
SRM 51−23−00 Pressure, Environmental, Fuel Tank and Firewall
Sealing
SRM 51−25−06 Fluid−Resistant (FR) Epoxy Primer
SRM 51−25−16 Fluid−Resistant (FR) Polyurethane Topcoat
SRM 51−26−00 Cleaning
SRM 51−40−11 How to Prepare Fastener Holes

### Page 53

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 52 of 97
Sep 29/2011
Revision D, Oct 22/2015
REFERENCE DESIGNATION
SRM 51−41−02 Bolts, Screws and Related Items
Tolerance Information
Linear Tolerances Angular Tolerance
X.XX in. (X.X mm) X.XXX in. (X mm)
+/−0° 30"+/− 0.03 in. +/− 0.01 in.
+/− 0.8 mm +/− .25 mm
NOTE: The tolerances above apply to the dimensions given in this service
bulletin, except when specified differently.
D. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Obey all the electrical/electronic safety precautions
(refer to AMM 24−00−00−910−801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR: FLIGHT CONTROLS FLIGHT CONTROL
SURFACES COMPONENTS THAT MOVE. MAKE SURE THAT THERE
ARE NO PERSONS OR EQUIPMENT ON OR NEAR THE FLIGHT
CONTROL SURFACES. ACCIDENTAL MOVEMENT OF THE FLIGHT
CONTROLS CAN CAUSE INJURIES TO PERSONS AND/OR DAMAGE
TO EQUIPMENT .
(2) Install the applicable warning placards on the pilot’s and the copilot’s control
wheels and the STAB TRIM/MACH TRIM panel.
CAUTION: MAKE SURE THAT THE REAR FUSELAGE SUPPORT IS PUT DIRECTLY
BELOW THE RIVET LINE AT FS755.00 (37 INCHES AFT OF THE
BAGGAGE COMPARTMENT DOOR). IF THE REAR FUSELAGE SUPPORT
IS NOT DIRECTLY BELOW THE RIVET LINE, DAMAGE TO THE AIRCRAFT
CAN OCCUR.

### Page 54

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 53 of 97
Sep 29/2011
Revision D, Oct 22/2015
(3) Remove the access panels that follow:
PANEL NAME REFERENCE
Middle Upper
Fairing Access panel AMM 55−32−05−000−806
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Middle Lower 
Fairing
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁ
Access panel
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
AMM 55−32−05−000−807
E. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
Bombardier in the Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com for analysis and to get an approved
disposition to complete this service bulletin.
Refer to Figure 4 and/or 5.
(2) Remove the HSTA (20), the trunnions (9), and the pins (1) and (13) from the
aircraft (refer to AMM 27−42−01−000−801 and the steps that follow).
(3) Make sure that the removed trunnions (9), and the pins (1) and (13) have a
serial number or are identified with a NCR part number.
 NOTE: NCR# xxxxxx−x can be any numerical and/or letter combination which
identifies a Non-Conformance Part (NCR).
(4) If the trunnion(s) (9) and/or the pin(s) (1) and/or (13) do not have a serial
number or are not identified with a NCR part number, speak with a
representative of Bombardier in the Customer Response Center at
+1−844−272−2720 (1−844−CRC−CRC0) or +1−514−855−8500 or
e-mail at thd.crj@aero.bombardier.com for analysis and to get an
approved disposition to complete this service bulletin.
(5) Record the position of the removed trunnions (9), and the pins (1) and (13).
(6) Discard the cotter pins (2), (12), and (18), the laminated shims (8), the nuts
(3), and (17).
(7) It is permissible to keep the bolts (7), (15), (19), the washers (10), and the
nuts (11) for a subsequent step.

### Page 55

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 54 of 97
Sep 29/2011
Revision D, Oct 22/2015
 NOTE: It is possible that the bolt(s) (7), (15), and/or (19) with a different
diameter can be necessary to install at the end of this procedure.
(8) Measure the diameter of the bolts (7), (15), and (19) that attach the trunnions
(9) and do as follows:
(a) Make sure that any oversize bolt(s) (7), (15), and (19) are the correct
length before the installation of the trunnions (9) in a subsequent step
(refer to Table 5).
(9) Measure the diameter of the bolts (6) and (14) that attach the upper pins (1)
and the lower pins (13) and do the steps that follow:
Refer to Figure 5.
(a) For the bolt(s) (6) and/or (14) that have a nominal diameter of 0.189 in.
(4.80 mm) do as follows:
1 It is permissible to keep the nominal diameter bolt(s) (6) and/or
(14) for a subsequent step.
2 It is permissible to keep the washer(s) (4) and/or (16) for a
subsequent step.
Refer to Figure 4.
(b) For the bolt(s) (6) and/or (14) that have an oversize diameter of 0.205 in.
(5.21 mm) or more, do as follows:
1 It is permissible to keep the oversize diameter bolt(s) (6) and/or
(14) for a subsequent step.
NOTE: It is possible that the bolt(s) (6) and/or (14) with a different
diameter can be necessary to install at the end of this
procedure.
2 Make sure that the oversize bolt(s) (6) and (14) are the correct
length before the installation of the upper pins (1) and the lower
pins (13) in a subsequent step (refer to Table 7 and Table 9).
3 Discard the washer(s) (4) and/or (16).
Refer to Figure 4 and/or 5.
(10) For the trunnions (9), do the procedure that follows.
 NOTE: This procedure is applicable to all four trunnions (9). The procedure that
follows is written for only one trunnion (9).

### Page 56

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 55 of 97
Sep 29/2011
Revision D, Oct 22/2015
(a) Clean the aircraft structure with solvent where the trunnion was installed
(refer to SRM 51−26−00).
(b) Measure the diameter of the two attach holes in the aircraft structure.
TABLE 1 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND TRUNNION
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE TRUNNION
HOLE
CONDITION NCR CONDITION
0.375 to 0.380 in.
(9.53 to 9.65 mm)
0.375 to 0.380 in.
(9.53 to 9.65 mm) Nominal No
0.391 to 0.396 in.
(9.93 to 10.06 mm)
0.391 to 0.396 in.
(9.93 to 10.06 mm) 1st oversize Yes
0.406 to 0.411 in.
(10.31 to 10.44 mm)
0.406 to 0.411 in.
(10.31 to 10.44 mm) 2nd oversize Yes
0.438 to 0.443 in.
(11.13 to 11.25 mm)
0.438 to 0.443 in.
(11.13 to 11.25 mm) Next size Yes
0.453 to 0.458 in.
(11.51 to 11.63 mm)
0.453 to 0.458 in.
(11.51 to 11.63 mm) 1st oversize Yes
0.469 to 0.474 in.
(11.91 to 12.04 mm)
0.469 to 0.474 in.
(11.91 to 12.04 mm) 2nd oversize Yes
0.500 to 0.505 in.
(12.70 to 12.83 mm)
0.500 to 0.505 in.
(12.70 to 12.83 mm) Next size Yes
(11) If the diameter of the attach hole(s) in the aircraft structure do not agree with
Table 1, speak with a representative of the Bombardier Customer Response
Center at +1−844−272−2720 (1−844−CRC−CRC0) or +1−514−855−8500
or e-mail at thd.crj@aero.bombardier.com to get an approved disposition.
(12) If the diameter of the attach holes in the aircraft structure are a nominal
dimension of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to Table 1), do as
follows:
(a) Measure the diameter of the attach holes in the trunnion (9).
(b) If the diameter of the attach hole(s) in the trunnion (9) is/are more than
0.380 in. (9.65 mm), do as follows:
1 Discard the trunnion (9).
2 Get a trunnion (9) P/N 601R92386−3 or alternative.

### Page 57

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 56 of 97
Sep 29/2011
Revision D, Oct 22/2015
NOTE: Trunnion P/N K601R92308−19 is a permitted alternative, if
trunnion P/N 601R92386−3 is not available.
3 Increase the diameter of the attach holes in the trunnion (9) to a
diameter of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to Table 1).
4 Remove the burrs and the sharp edges from the trunnion (9).
5 Apply a chemical conversion coating on the bare metal surfaces of
the trunnion (9) (refer to SRM 51−21−11).
(c) If the diameter of the related attach hole(s) in the trunnion (9) is/are a
nominal dimension of 0.375 to 0.380 in. (9.53 to 9.65 mm), do as follows:
1 Examine the general condition of the trunnion (9) for damage(s)
(refer to SRM 51−10−06).
2 If damage is found on the trunnion (9), do revision B or the latest
approved revision of GREO 601R−27−42−007.
3 If the trunnion (9) cannot be repaired with revision B or the latest
approved revision of GREO 601R−27−42−007, do as follows:
a Discard the trunnion (9).
b Get a trunnion (9) P/N 601R92386−3 or alternative.
NOTE: Trunnion P/N K601R92308−19 is a permitted
alternative, if trunnion P/N 601R92386−3 is not
available.
c Increase the diameter of the attach holes in the trunnion (9) to
a diameter of 0.375 to 0.380 in. (9.53 to 9.65 mm) (refer to
Table 1).
d Remove the burrs and the sharp edges from the trunnion (9).
e Apply a chemical conversion coating on the bare metal
surfaces of the trunnion (9) (refer to SRM 51−21−11).
(d) If the trunnion (9) is replaced with P/N 601R92386−3 or
K601R92308−19, record the serial number in the applicable logbooks.
(13) If the diameter of the attach hole(s) in the aircraft structure is/are an oversized
dimension of more than 0.380 in. (9.65 mm) and equal to or less than 0.505
in. (12.83 mm) (refer to Table 1), do as follows:
(a) Measure the diameter of the attach holes in the trunnion (9).

### Page 58

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 57 of 97
Sep 29/2011
Revision D, Oct 22/2015
(b) If the diameters of the related attach holes in the trunnion (9) agree with
the diameter of the related attach holes in the aircraft structure
(refer to Table 1), do as follows:
1 Make sure that the edge distance for the attach holes in the
trunnion (9) are a minimum of 0.9D.
2 If the edge distance for the related attach hole(s) in the trunnion (9)
is/are less than 0.9D, speak with a representative of the Bombardier
Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
3 Examine the general condition of the trunnion (9) for damage(s)
(refer to SRM 51−10−06).
4 If damage(s) is/are found, do revision B or the latest approved
revision of GREO 601R−27−42−007.
5 If the trunnion (9) cannot be repaired with revision B or the latest
approved revision of GREO 601R−27−42−007, go to step 2.E.(14)
for the replacement of the trunnion (9).
(c) If the diameter of the related attach hole(s) in the trunnion (9) do not
agree with the diameter of the related attach hole(s) in the aircraft
structure (refer to Table 1), do as follows:
1 If the diameter of the related attach hole(s) in the trunnion (9) is/are
larger than the related attach hole(s) in the aircraft structure, (refer
to Table 1), do as follows:
a Discard the trunnion (9).
b Go to step 2.E. (14) for the replacement of the trunnion (9).
2 If the diameter of the related attach hole(s) in the trunnion (9) is/are
smaller than the related attach hole(s) in the aircraft structure, do
as follows:
a Increase the diameter of the attach hole(s) in the trunnion (9) to
agree with the related NCR condition in the aircraft structure (refer
to Table 1).
b Make sure that the edge distance for the related attach holes
in the trunnion (9) are a minimum of 0.9D.

### Page 59

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 58 of 97
Sep 29/2011
Revision D, Oct 22/2015
c If the edge distance for the related attach hole(s) in the trunnion
(9) is/are less than 0.9D, speak with a representative of the
Bombardier Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
d Remove the burrs and the sharp edges from the trunnion (9).
e Apply a chemical conversion coating on the bare metal
surfaces of the trunnion (9) (refer to SRM 51−21−11).
f Examine the general condition of the trunnion (9) for
damage(s) (refer to SRM 51−10−06).
g If damage(s) is/are found, do revision B or the latest
approved revision of GREO 601R−27−42−007.
h If the trunnion (9) cannot be repaired with revision B or the latest
approved revision of GREO 601R−27−42−007, go to step
2.E.(14) for the replacement of the trunnion (9).
(d) If the trunnion (9) is repaired with revision B or the latest approved
revision of GREO 601R−27−42−007, or if no damage(s) is/are found,
go to step 2.E.(27) to change the identification of the trunnion (9) to
K601R92308−31.
(14) To replace the trunnion (9) that has an oversized attach hole(s) (NCR
condition) in the aircraft structure of more than 0.380 in. (9.65 mm) and equal
to or less than 0.505 in. (12.83 mm) (refer to Table 1), do as follows:
(a) Replace the trunnion (9) where there is a NCR condition with trunnion
P/N K601R92308−51.
 NOTE: The identification procedure is not necessary as the trunnion P/N
K601R92308−51 is identified.
(b) Align the center hole of the trunnion (9) with the center hole of the
aircraft structure and attach temporarily.
(c) As necessary, make marks on the trunnion (9) to find the correct
center points of the aircraft structure attach holes.
(d) Remove the temporarily attached trunnion (9) from the aircraft
structure.
(e) Make sure that the edge distance for the attach holes in the trunnion
(9) are a minimum of 0.9D.

### Page 60

SERVICE BULLETIN  601R−27−160
SB 601R−27−160
Page 59 of 97
Sep 29/2011
Revision D, Oct 22/2015
(f) If the edge distance for the attach hole(s) in the trunnion (9) is/are
less than 0.9D, speak with a representative of the Bombardier
Customer Response Center at +1−844−272−2720
(1−844−CRC−CRC0) or +1−514−855−8500 or e-mail at
thd.crj@aero.bombardier.com to get an approved disposition.
(g) Drill the center point of the attach holes in the trunnion (9) to a
diameter of .098 in. (2.49 mm) (refer to SRM 51−40−11).
(h) Increase the diameter of the attach holes in the trunnion (9) to agree
with the related NCR condition in the aircraft structure (refer to Table
1).
(i) Remove the burrs and sharp edges from the trunnion (9).
(j) Apply a chemical conversion coating on the bare metal surfaces of
the trunnion (9) (refer to SRM 51−21−11).
(k) Record the serial number of the trunnion (9) in the applicable
logbooks.
(15) For the upper pins (1), do the procedure that follows:
 NOTE: This procedure is applicable to the two upper pins (1). The
procedure that follows is written for only one upper pin (1).
(a) Clean the aircraft structure with solvent where the pin attaches
(refer to SRM 51−26−00).
(b) Measure the diameter of the two attach holes in the aircraft
structure.
TABLE 2 − ATTACH HOLE DIMENSIONS − AIRCRAFT STRUCTURE AND UPPER PIN
DIAMETER OF THE
ATTACH HOLES IN
THE AIRCRAFT
STRUCTURE
DIAMETER OF THE
ATTACH HOLES IN
THE UPPER PIN
HOLE CONDITION NCR CONDITION
0.189 to 0.195 in
(4.80 to 4.95 mm)
0.215 to 0.225 in
(5.46 to 5.72 mm) Nominal No
0.205 to 0.210 in
(5.21 to 5.33 mm)
0.225 to 0.235 in
(5.72 to 5.97 mm) 1st oversize Yes
0.221 to 0.226 in
(5.61 to 5.74 mm)
0.239 to 0.249 in
(6.07 to 6.32 mm) 2nd oversize Yes
0.250 to 0.255 in
(6.35 to 6.48 mm)
0.270 to 0.280 in
(6.86 to 7.11 mm) Next size Yes

The text continues at https://openairdocs.org/service-documents/bombardier/601r-27-160/file/e4f07e28c3df.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
