# Bombardier Service Bulletin 601R-57-046

Copy: Revision C ("SB 601R-57-046 Rev C"), 110 pages: PDF https://openairdocs.org/files/sha256/7c/f8/7cf85120c1199e47ac6f6710f45ac8c2a101505767d875378743cbd83da89756; text https://openairdocs.org/service-documents/bombardier/601r-57-046/file/7cf85120c119.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0801; AD 2019-08-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 601R-57-046
- Latest revision known: 601R-57-046, Revision C, dated December 20, 2012 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/601r-57-046

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2019-08-11](https://openairdocs.org/ad/2019-08-11.md), effective Jul 11, 2019: Revisions A, B and C

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/601r-57-046/proposed.md), [2 difficulty reports](https://openairdocs.org/service-documents/bombardier/601r-57-046/reports.md).

## Text (110 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0801; AD 2019-08-11 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB 601R- - - 57- - - 046
Page 1 of 1
Dec 20/2012
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
CL- - -600- - -2B19Canadair Regional Jet (CRJ) Aircraft
SERVICE BULLETIN 601R - - -57 - - -046
SUBJECT : Wings - - - Center Wing Primary Structure - - - Cold Working of Fastener
Holes in the Main Landing Gear (MLG) Trunnion Fitting
This page transmits:
Revision C of Service Bulletin 601R- - - 57- - - 046,
pages 1 thru 108, dated Dec 20/2012.
The changes in this revision have no effect on aircraft that have
incorporated a previous issue of this service bulletin.
Reason:
Revised Accomplishment Instructions, paragraph 2., to:
Revise some steps.
This revision also includes small editorial changes that do not have an effect on the technical
content.
Instructions:
Discard the copy of Service Bulletin 601R- - - 57- - - 046, Revision B, dated Aug 24/ 2012.
Replace with the copy attached.
Service Bulletin History:
Initial issue, dated Jul 17/2009.
Revision A, dated Dec 21/2009.
Revision B, dated Aug 24/2012.
1

### Page 2

SB 601R- - - 57- - - 046
Page 1 of 108
Jul 17/2009
Revision C, Dec 20/2012
SERVICE BULLETIN
T echnical
Publications
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS LEASED
HAS SOLD AIRCRAFT OR TRANSFERRED SPARES IN THE LAST SIX MONTHS, THIS SERVICE
BULLETIN MUST BE SENT TO THE NEW OWNER, UNLESS CONFIRMATION WAS RECEIVED
THAT BOMBARDIER REGIONAL AIRCRAFT DIVISION HAS INCLUDED THE NEW OPERATOR
AIRCRAFT , THIS SERVICE BULLETIN MUST BE SENT TO THE LESSEE. IF THE OPERATOR
ON THE DISTRIBUTION LIST .
ATA SYSTEM: 57- - -11 NUMBER: 601R - - -57- - -046
SUBJECT : Wings - - - Center Wing Primary Structure - - - Cold Working of Fastener
Holes in the Main Landing Gear (MLG) Trunnion Fitting
1. PLANNING INFORMATION
A. Effectivity
Service Bulletin: CL- - - 600- - - 2B19 Canadair Regional Jet (CRJ) Aircraft Serial
Numbers 7003 thru 7067, 7069 thru 7990 and 8000 thru
8106.
Production: This change will be incorporated before delivery on aircraft
with serial number 8107 and subsequent serial numbers.
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Service Bulletins. Before you do this service
bulletin, examine all Supplemental Type Certificates (STCs),
Supplemental Type Approvals (STAs) or equivalent changes to make
sure you can complete this service bulletin.
NOTE: The procedure in this service bulletin was validated on Aircraft 7731.

### Page 3

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 2 of 108
Jul 17/2009
Revision C, Dec 20/2012
B. Reason
(1) Condition
It is possible for cracks to start in the fastener holes of the lower flange of the
the MLG trunnion.
(2) Evidence
Engineering analysis has found that cracks can occur in the fastener holes of
the lower flange of the MLG trunnion.
(3) Objective/Benefit
This service bulletin gives the procedure to cold work the fastener holes in the
MLG trunnion. Cold work of the fastener holes will increase the life of the
MLG trunnion fitting.
C. Description
This service bulletin is divided into seven parts: PART A, PART B, PART C, PART D,
PART E, PART F and PART G.
For Aircraft 7003 - - -7010, 7013 - - -7067, 7069 - - -7990 and 8000 - - -8017
PART A - - - Cold Work of the Fastener Holes in the Left MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
PART B - - - Cold Work of the Fastener Holes in the Right MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.

### Page 4

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 3 of 108
Jul 17/2009
Revision C, Dec 20/2012
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
For Aircraft 7011 and 7012
PART C - - - Cold Work of the Fastener Holes in the Left MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
PART D - - - Cold Work of the Fastener Holes in the Right MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
For Aircraft 8018 - - -8106
PART E - - - Cold Work of the Fastener Holes in the Left MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.

### Page 5

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 4 of 108
Jul 17/2009
Revision C, Dec 20/2012
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
PART F - - - Cold Work of the Fastener Holes in the Right MLG Trunnion
The MLG lockpins are installed. The electrical power is applied to the aircraft. The
PCU safety tool is installed. The aircraft is put on jacks. The flaps are extended.
Electrical power is removed from the aircraft. Circuit breakers are opened.
Electrical harness is removed. An access panel is removed. MLG door is removed.
The fasteners are removed. The fastener holes are inspected, cold worked and new
oversized fasteners are installed in the lower wing plank, in the MLG trunnion fitting
and if necessary in the trunnion strap.
The access panel is installed. The electrical harness is installed. The PCU safety
tool is removed. Circuit breakers are closed. The flaps are retracted. MLG door is
installed. The aircraft is removed from jacks. The lockpins are removed from the
MLG.
For aircraft that have incorporated the initial issue or revision A of this service bulletin
PART G - - - Identification of the Left and Right MLG Trunnion
Lockpins are installed in the MLG. The left and right MLG trunnions are identified.
For all Aircraft
D. Compliance
Recommended Service Bulletin. Bombardier Aerospace recommends that PART A
and PART B or PART C and PART D or PART E and PART F of this service bulletin
be done before the aircraft have 34 900 flight cycles, unless otherwise directed by
the airworthiness authority of the operator.

### Page 6

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 5 of 108
Jul 17/2009
Revision C, Dec 20/2012
For aircraft that have incorporated the initial issue or revision A of this service bulletin
Recommended Service Bulletin. Bombardier Aerospace recommends that PART G
of this service bulletin be done before the aircraft have 38 900 flight cycles, unless
otherwise directed by the airworthiness authority of the operator.
NOTE: If the identification of the MLG trunnion was done with Service Bulletin
601R- - - 57- - - 047 or 601R- - - 57- - - 048, it is not necessary to do PART G of this
service bulletin.
For all Aircraft
This service bulletin affects Airworthiness Limitations (AWLs) and/or Damage
T olerance Inspections (DTIs). Reference applicable Post/Pre Modsum
TC601R17174 and/or Service Bulletin 601R- - - 57- - - 046 in the Maintenance
Requirements Manual (MRM).
E. Approval
The technical content of this service bulletin has been approved under the authority
of the TCCA Design Approval Organization No: DAO #93- - -Q- - -02.
F. M a n p o w e r
Man hours given below are estimates for direct labor done by an experienced crew
on an aircraft prepared for maintenance.
These estimates do not include the time necessary for:
 Administrative functions such as planning, liaison, familiarization, and report writing.
 Non productive elapsed time such as rest time, having meals, and crew shift
changes.
 Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
 Preparation for modification (unless specified in the accomplishment
instructions) such as cleaning and getting parts, tools, consumables, and
ground equipment.
 Quality assurance inspections, troubleshooting and/or correction of
discrepancies found when a task is done.
 All other activities that are not considered by Bombardier Aerospace as directly
related to the accomplishment of this procedure.

### Page 7

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 6 of 108
Jul 17/2009
Revision C, Dec 20/2012
NOTE: For on-site labor assistance, please speak with a Fleet Services
representative for a quote. The Fleet Services Team can be
contacted via the CRC at 514- - - 855- - - 8500 or email at
thd.crj@aero.bombardier.com.
For PART A
It will take an estimated 9.0 man-hours to complete PART A of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 2.0
(2) Procedure 5.0
(3) T est N/A
(4) Job Close- - -Out 2.0
For PART B
It will take an estimated 9.0 man-hours to complete PART B of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 2.0
(2) Procedure 5.0
(3) T est N/A
(4) Job Close- - -Out 2.0

### Page 8

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 7 of 108
Jul 17/2009
Revision C, Dec 20/2012
For PART C
It will take an estimated 5.0 ma-hours to complete PART C of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 1.0
(2) Procedure 3.0
(3) T est N/A
(4) Job Close- - -Out 1.0
For PART D
It will take an estimated 5.0 man-hours to complete PART D of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 1.0
(2) Procedure 3.0
(3) T est N/A
(4) Job Close- - -Out 1.0
For PART E
It will take an estimated 8.0 man-hours to complete PART E of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 2.0
(2) Procedure 4.0
(3) T est N/A
(4) Job Close- - -Out 2.0

### Page 9

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 8 of 108
Jul 17/2009
Revision C, Dec 20/2012
For PART F
It will take an estimated 8.0 man-hours to complete PART F of this service bulletin.
The man- - - hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 2.0
(2) Procedure 4.0
(3) T est N/A
(4) Job Close- - -Out 2.0
For PART G
It will take an estimated 0.25 man-hours to complete PART G of this service bulletin.
The man-hours are divided as shown in the table that follows:
TASK MAN-HOURS
( 1 ) J o b S e t --- U p 0.0
(2) Procedure 0.25
(3) T est 0.0
(4) Job Close- - -Out 0.0
G. Material - - - Price and Availability
(1) The kits in the table that follows are available from Bombardier Aerospace
Regional Aircraft. Refer to the paragraph below for terms and conditions.
NOTE: For a list of the kit contents, refer to paragraph 3.A.

### Page 10

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 9 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7003 - - -7010, 7013 - - -7067, 7069 - - -7990 and 8000 - - -8017
PART A
KIT NUMBER NAME
601R57- - - 046K1 Left MLG Trunnion Hardware
PART B
KIT NUMBER NAME
601R57- - - 046K2 Right MLG Trunnion Hardware
For Aircraft 7011 and 7012
PART C
KIT NUMBER NAME
601R57- - - 046K3 Left MLG Trunnion Hardware
PART D
KIT NUMBER NAME
601R57- - - 046K4 Right MLG Trunnion Hardware
For Aircraft 8018 - - -8106
PART E
KIT NUMBER NAME
601R57- - - 046K5 Left MLG Trunnion Hardware
PART F
KIT NUMBER NAME
601R57- - - 046K6 Right MLG Trunnion Hardware

### Page 11

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 10 of 108
Jul 17/2009
Revision C, Dec 20/2012
For all Aircraft
(2) Please send a purchase order to the address below to schedule the kits:
Bombardier
Customer Account Service T eam (CAST) - - - Kit Group
123 Garratt Blvd, N42- - - 24
Downsview, Ontario
Canada M3K 1Y5
Fax: 416- - - 375- - - 3060
Phone: 416- - - 375- - - 3920
Email: sbkits@aero.bombardier.com
(3) Refer to paragraph 3.C. for a list of consumables for this service bulletin.
H. T ooling - - - Price and Availability
(1) The tool kit in the table that follows is available from Bombardier Aerospace
Regional Aircraft. Refer to the paragraph below for the terms and conditions.
NOTE: For a list of the kit contents, refer to paragraph 3.A.
For PART A, PART B, PART C, PART D, PART E and PART F
KIT NUMBER NAME TERMS ANDCONDITIONS
601R57- - - 046K90 MLG Trunnion - - - Cold WorkT ools Refer toparagraph 1.H.(2).
601R57- - - 046K91 MLG Trunnion - - - Reamers Refer toparagraph 1.H.(2).
SBTOOL- - - 004K90 Hydraulic Powerpack Refer toparagraph 1.H.(2).
SBTOOL- - - 005K90 LB Puller Assy Refer toparagraph 1.H.(2).

### Page 12

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 11 of 108
Jul 17/2009
Revision C, Dec 20/2012
(2) Please send a purchase order to the address below to schedule the kits:
Bombardier
Customer Account Service T eam (CAST) - - - Kit Group
123 Garratt Blvd, N42- - - 24
Downsview, Ontario
Canada M3K 1Y5
Fax: 416- - - 375- - - 3060
Phone: 416- - - 375- - - 3920
Email: sbkits@aero.bombardier.com
NOTE: When this service bulletin is completed, tooling kits SBTOOL- - - 004K90
and SBTOOL- - - 005K90 must be returned to the address below. Please
contact the Customer Account Service T eam - - - Kit Group to get a Return
Material Approval (RMA):
Bombardier - - - Chicago Warehouse Distribution
251- - - A Wille Road
Des Plaines, Illinois
USA 60018- - - 1817
I. Weight and Balance
Not changed.
J. Electrical Load Data
Not changed.
K. References
Restriction and/or Special Instruction (RSI) C- - -A251, Revision C
Modification Summary TC601R17174, Revision D
Aircraft Maintenance Manual (AMM)
Structural Repair Manual (SRM)
Non Destructive T esting Manual (NDTM)
Refer to the SB Introduction document for definition or explanation of Service
Bulletin content.
For Bombardier Aerospace reference only: PCA 03993.
L. Other Publications Affected
Aircraft Illustrated Parts Catalogue (AIPC)
Maintenance Requirement Manual (MRM)

### Page 13

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 12 of 108
Jul 17/2009
Revision C, Dec 20/2012
M. Relationship Chart
PRE-SB
PART NUMBER NAME POST-SBPART NUMBER NAME
601R10031- - - 1 MLG Trunnion
K601R10032- - - 1¡
or
K601R10032- - - 3©
or
K601R10032- - - 9¢
MLG Trunnion
601R10031- - - 2 MLG Trunnion
K601R10032- - - 2¡
or
K601R10032- - - 4©
or
K601R10032- - - 10¢
MLG Trunnion
601R10031- - - 11 MLG Trunnion K601R10032- - - 3£ MLG Trunnion
601R10031- - - 12 MLG Trunnion K601R10032- - - 4£ MLG Trunnion
601R10068- - - 1 MLG Trunnion K601R10032- - - 5¤ MLG Trunnion
601R10068- - - 2 MLG Trunnion K601R10032- - - 6¤ MLG Trunnion
601R10068- - - 5 MLG Trunnion K601R10032- - - 7¥ MLG Trunnion
601R10068- - - 6 MLG Trunnion K601R10032- - - 8¥ MLG Trunnion
¡ For Aircraft 7003- - - 7010, 7013- - - 7067 and 7069- - - 7138 Pre- - - REO
601R- - - 57- - - 21- - - 003 and Pre- - - SB 601R- - - 32- - - 054 that have incorporated service
bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048.
© For Aircraft 7003- - - 7010, 7013- - - 7067 and 7069- - - 7138 Post- - - REO
601R- - - 57- - - 21- - - 003 or Post- - - SB 601R- - - 32- - - 054 that have incorporated service
bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048.
¢ For Aircraft 7011 and 7012 that have incorporated service bulletins 601R- - - 32- - - 097,
601R- - - 57- - - 046 and 601R- - - 57- - - 048.
£ For Aircraft 7139- - - 7990 and 8000- - - 8017 that have incorporated service bulletins
601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048.
¤ For Aircraft 8018- - - 8079 that have incorporated service bulletins 601R- - - 57- - - 046 and
601R- - - 57- - - 048.
¥ For Aircraft 8080- - - 8106 that have incorporated service bulletins 601R- - - 57- - - 046 and
601R- - - 57- - - 048.

### Page 14

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 13 of 108
Jul 17/2009
Revision C, Dec 20/2012
2. ACCOMPLISHMENT INSTRUCTIONS
For Aircraft 7003 - - -7010, 7013 - - -7067, 7069 - - -7990 and 8000 - - -8017
PART A - - - Cold Work of the Fastener Holes in the Left MLG Trunnion
A. Job S e t --- U p
Reference Information
REFERENCE DESIGNATION
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 1 Put the Aircraft on Jacks
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 4 Removal of the Aircraft from Jacks
A M M 1 0 --- 1 1 --- 0 0 --- 4 0 0 --- 8 0 2Installation of the Main Landing Gear Lockpins
A M M 1 0 --- 1 1 --- 0 0 --- 0 0 0 --- 8 0 2Removal of the Main Landing Gear Lockpins
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 1Pressurize Hydraulic Systems No. 1 and No. 2
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 2Release Hydraulic Pressure - - - Systems No. 1
and No. 2
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 1 Connect External AC Power
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 2 Remove External AC Power
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 2 Lockwire - - - Maintenance Practices
A M M 2 4 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Electrical/Electronic Safety Precautions
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 1 Electrical Extension of the Flaps
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 2 Electrical Retraction of the Flaps
A M M 2 9 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Hydraulic Safety Precautions
NDTM 53- - - 00- - - 097 General Procedure for Inspection of Surface
Cracks in Bolt Holes of Aluminum Alloy Parts
S R M 5 1 --- 2 1 --- 1 1 Corrosion Prevention Procedures
S R M 5 1 --- 2 3 --- 0 0 Pressure, Environment, Fuel Tank and Firewall
Sealing
S R M 5 1 --- 2 4 --- 3 8 Cold Working of Fastener Holes

### Page 15

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 14 of 108
Jul 17/2009
Revision C, Dec 20/2012
REFERENCE DESIGNATION
S R M 5 1 --- 2 5 --- 0 6 Fluid-Resistant (FR) Epoxy Primer
S R M 5 1 --- 2 5 --- 1 6 Fluid-Resistant (FR) Polyurethane Topcoat
S R M 5 1 --- 2 6 --- 0 0 Cleaning
S R M 5 1 --- 4 0 --- 1 1 How to Prepare Fastener Holes
S R M 5 1 --- 4 2 --- 2 1 Hi-Lite Fasteners
(1) Install the lockpins on the main landing gears
(Refer to AMM 10- - - 11- - - 00- - - 400- - - 802).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT . IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions
(Refer to AMM 24- - - 00- - - 00- - - 910- - - 801).
(3) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR:
--- F L I G H T C O N T R O L S
- - - FLIGHT CONTROL SURFACES AND
- - - COMPONENTS THAT MOVE.
MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT ON OR
NEAR THE FLIGHT CONTROL SURFACE. ACCIDENTAL MOVEMENT
OF THE FLIGHT CONTROL CAN CAUSE INJURIES TO PERSON
AND/OR DAMAGE TO EQUIPMENT .
(4) Install the PCU safety tool on the PCU of the inboard ground spoiler as
follows:
WARNING: OBEY ALL THE HYDRAULIC SAFETY PRECAUTIONS WHEN YOU
DO WORK ON ANY HYDRAULIC SYSTEM OR ON A HYDRAULIC
SYSTEM COMPONENT . IF YOU DO NOT OBEY THE SAFETY
PRECAUTIONS, YOU CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE TO EQUIPMENT .

### Page 16

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 15 of 108
Jul 17/2009
Revision C, Dec 20/2012
(a) Obey all the hydraulic safety precautions
(Refer to AMM 29- - - 00- - - 00- - - 910- - - 801).
(b) Pressurize hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 801).
( c ) M a k es u r et h a ty o uh a v et h ec o n d i t i o n st h a tf o l l o wt ol e tt h eg r o u n d
spoilers deploy:
- - - Power levers at IDLE.
- - - Both WOW circuits in a weight-on-wheels condition.
- - - Radio altitude indication at less than five feet.
(d) On the SPOILERS panel, set the GND LIFT DUMPING switch to MAN
ARM. Make sure that the applicable spoiler surfaces extend.
(e) Keep the AC electrical power on and the spoilers in the extended
position.
(f) Release the pressure from hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 802).
(g) When the hydraulic pressure is at zero, disconnect the external AC
power (Refer to AMM 12- - - 00- - - 07- - - 861- - - 802).
(h) Install the PCU safety tool on the PCU on the inboard ground spoiler.
(5) Put the aircraft on jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 801).
(6) Extend the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 801).
(7) On the inboard flap, pull the movable leading- - -edge vane to the flap. This will
l e ty o ug e ta c c e s st ot h ew o r ka r e ao nt h er e a rs p a r .
(8) Use a strap or equivalent to keep the movable leading-edge vane retracted.

### Page 17

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 16 of 108
Jul 17/2009
Revision C, Dec 20/2012
(9) Open, safety, and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(10) At WS56.17 and WS75.50, remove nuts (1), screws (3), and washers (2) from
clamps (4).
(11) If necessary, remove the proximity sensor (8) of the inboard ground spoiler
from the mounting bracket as follows:
(a) Remove nuts (5) and (7) and lock washer (6) from the proximity sensor.
(b) Put a plastic bag on the proximity sensor to prevent damage.
(c) Move the proximity sensor (8) and electrical harness away from the work
area.
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Post SB 601R - - -27 - - -115 and for Aircraft
7612 and 7645 - - -8017
Refer to Figure 2.
(12) If necessary, between WS56.17 and WS75.50, remove the connector P7GA as
follows:

### Page 18

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 17 of 108
Jul 17/2009
Revision C, Dec 20/2012
(a) Between WS56.17 and WS75.50, remove screws (1) and washers (2)
from the bracket (5).
(b) Remove the lockwire from the connector (3).
(c) On the inboard side of the proximity sensor of the inboard ground
spoiler, disconnect the connector (3) from the receptacle (4).
(d) Install a cap to prevent damage to the connector (3).
(e) Move the electrical harness away from the work area.
For all Aircraft
(13) Remove the access panel that follows from the upper wing surface:
ACCESS PANEL DESCRIPTION
540AT Access Panel
Refer to Figure 9.
(14) Remove the left MLG door (1) as follows:
For Aircraft with MLG door 601R31240 installed
(a) Remove the nut (2), washers (4) and bonding jumper (6) from the
ground stud (19).
For Aircraft with MLG door 601R31178 installed
(b) Remove the nut (3), washers (4), bolt (5) and bonding jumper (6) from
the MLG door (1).
For all Aircraft
(c) Remove and discard the cotter pin (7).
(d) Remove the nut (8), bolt (10) and the washer (9). Disconnect the rod end
(11) from the MLG door (1).
(e) Remove and discard cotter pins (12).
(f) Remove nuts (14), pins (18), washers (15) and (17) and shim washers
(16) from the door hinges (13).
(g) Remove the MLG door (1).

### Page 19

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 18 of 108
Jul 17/2009
Revision C, Dec 20/2012
B. Procedure
NOTE: Kits 601R57- - - 046K1, 601R57- - - 046K90 and 601R57- - - 046K91 are
necessary to do the procedure that follows.
Refer to Figure 3.
(1) Remove 23 Hi- - -Lite pins and collars from the MLG trunnion at the same
location as fasteners (1), (2), (3), and (4) (Refer to SRM 51- - - 42- - - 21).
(2) Make sure that you use the applicable clamping method to hold the strap, the
lower wing plank and the MLG trunnion together.
Refer to Figure 3 and 4.
(3) Cold work a hole for installation of Hi- - -Lite (1) in the MLG trunnion as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 8- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open a hole to a diameter between 0.2684 in. and 0.2694 in. (6.817 mm
and 6.843 mm) with the reamer (P/N 601R57046K91- - - 3).
(b) Do an eddy current inspection of the fastener hole
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 7), make sure the
fastener hole has a diameter of 0.2684 in. to 0.2694 in. (6.817 mm to
6.843 mm).
(e) Before cold working, enlarge the countersink of the fastener hole
sufficiently to receive the Hi- - -Lite (1).
(f) Cold work a hole in the MLG trunnion, the strap and the lower wing
plank (Refer to SRM 51- - - 24- - - 38).

### Page 20

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 19 of 108
Jul 17/2009
Revision C, Dec 20/2012
NOTE: U s e s t r a i g h t s l e e v e C B S --- 8 --- 2 --- N --- 2 4 S .
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 8 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 8- - - 2- - - N- - - 1- - - .2780), ream the
fastener hole to a final diameter of 0.2775 in. to 0.2792 in. (7.049 mm to
7.092 mm).
(4) Cold work 22 holes for installation of Hi- - -lites (2), (3) and (4) in the MLG
trunnion as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 10- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open 22 holes to a diameter between 0.3305 in. and 0.3320 in. (8.395
mm and 8.433 mm) with the reamer (P/N 601R57046K91- - - 5).
(b) Do an eddy current inspection of the fastener holes
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 9), make sure the
fastener holes have a diameter of 0.3305 in. to 0.3320 in. (8.395 mm to
8.433 mm).
(e) Before cold working, enlarge the countersinks of the fastener holes
sufficiently to receive Hi- - -Lites (2), (3) and (4).
(f) Cold work 22 fastener holes in the MLG trunnion (Refer to SRM
51- - - 24- - - 38).
NOTE: S t r a i g h t s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 2 S a r e n e c e s s a r y t o d o t h e
cold work through lower wing plank and MLG trunnion. Straight
s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 6 S a r e n e c e s s a r y t o d o t h e c o l d w o r k
through the trunnion strap, lower wing plank and MLG trunnion.

### Page 21

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 20 of 108
Jul 17/2009
Revision C, Dec 20/2012
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 1 0 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 10- - - 2- - - N- - - 1- - - .3405), ream the
fastener holes to a final diameter of 0.3400 in. to 0.3417 in. (8.636 mm to
8.679 mm).
(5) Make sure that the countersinks have no ridge(s).
(6) If ridge(s) is/are found, manually remove the ridge(s) with a countersink tool.
(7) Apply chemical conversion coating or equivalent in the fastener holes
( R e f e r t o S R M 5 1 --- 2 1 --- 1 1 ) .
( 8 ) W e t --- i n s t a l l H i --- l i t e s ( 2 ) a n d c o l l a r s ( 6 ) t h r o u g h t h e l o w e r w i n g p l a n k a n d t h e
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(9) Prepare the radius washer (7) as follows:
(a) Open the hole in the radius washer (7) to a diameter of 0.348
- - - 0.001/+0.006 in. (8.84 - - - 0.03/+0.15 mm).
(b) T emporarily put the radius washer (7) in position on the inner side of the
aft flange of the MLG trunnion.
(c) Make sure the radius washer (7) sits correctly in the radius.
(d) If necessary, remove unwanted material on the radius washer (7) to get a
correct installation.
(e) Make sure that you keep a minimum edge distance of 0.9D.
(f) Apply chemical conversion coating on the bare metal areas
(Refer to 51- - - 21- - - 11).
(g) Apply one layer of primer in the fastener hole (Refer to SRM 51- - - 25- - - 06).
(10) Install the radius washer (7) with faying surface sealant and wet- - - install
Hi- - - Lite (3) and collar (6) through the lower wing plank and MLG trunnion
( R e f e r t o S R M 5 1 --- 2 3 --- 0 0 a n d S R M 5 1 --- 4 2 --- 2 1 ) .
(11) Wet- - -install Hi- - -Lites (4) and collars (6) through the strap, lower wing plank

### Page 22

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 21 of 108
Jul 17/2009
Revision C, Dec 20/2012
and MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(12) Wet- - - install Hi- - - Lite (1) and collar (5) through the strap, lower wing plank and
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(13) Apply a layer of epoxy primer on Hi- - - Lites (1), (2), (3) and (4) and collars (5)
and (6) (Refer to SRM 51- - - 25- - - 06).
(14) Apply a layer of polyurethane topcoat on Hi- - - Lites (1), (2), (3) and (4) and
collars (5) and (6) (Refer to SRM 51- - - 25- - - 16).
(15) Do the identification of the MLG trunnion as follows:
(a) If a MLG trunnion was repaired or replaced, speak with a representative
of the Customer Response Centre (CRC) at 514- - - 855- - - 8500 for an
identification number.
For Aircraft 7003 - - -7010, 7013 - - -7067 and 7069 - - -7138 Pre-REO 601R - - -57 - - -21 - - -003 and
Pre-SB 601R - - -32 - - -054
(b) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 1.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .
For Aircraft 7003 - - -7010, 7013 - - -7067 and 7069 - - -7138 Post-REO 601R - - -57 - - -21 - - -003 or
Post-SB 601R - - -32 - - -054
(c) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 3.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .

### Page 23

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 22 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7139 - - -7990 and 8000 - - -8017
(d) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 3.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .
C. Close Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Install the access panel that follows on the upper wing surface:
ACCESS PANEL DESCRIPTION
540AT Access Panel
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(3) If removed, install the proximity sensor (8) of the inboard ground spoiler as
follows:
(a) Install the proximity sensor (8) of the inboard ground spoiler on the
mounting bracket with the lock washer (6) and nuts (5) and (7).
(b) Adjust the position of the proximity sensor (8). Make sure there is a
clearance of 0.035 to 0.055 in. (0.89 to 1.40 mm) between the proximity
sensor (8) and the target.
(c) Safety the proximity sensor (8) with lockwire.
(4) At WS56.17 and WS75.50, install clamps (4), screws (3), washers (2) and nuts
(1) to keep the electrical harness in position.

### Page 24

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 23 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Post SB 601R - - -27 - - -115 And for Aircraft
7612 and 7645 - - -8017
Refer to Figure 2.
(5) If removed, between WS56.17 and WS75.50, install the connector P7GA as
follows:
(a) Between WS56.17 and WS75.50, install the bracket (5) with screws (1)
and washers (2).
(b) At WS67.25, connect the connector (3) to the receptacle (4).
(c) Safety the connector (3) with lockwire.
For all Aircraft
(6) Remove the PCU safety tool from the PCU of the inboard ground spoiler.
(7) Remove the strap on the flap to extend the movable leading- - - edge vane.
(8) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
(9) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
(10) Retract the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 802).

### Page 25

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 24 of 108
Jul 17/2009
Revision C, Dec 20/2012
Refer to Figure 9.
(11) Install the left MLG door (1) as follows:
(a) Install pins (18) through door hinges (13) with washers (15) and (17),
shim washers (16) and nuts (14).
(b) T orque the nuts (14) to a maximum of 20 lbf Sin (2.26 NS m).
(c) Safety the nuts (14) with cotter pins (12).
(d) Attach the rod end (11) to the MLG door (1) with the bolt (10), washer (9)
and the nut (8).
(e) Safety the nut (8) with the cotter pin (7).
For Aircraft with MLG door 601R31240 installed
(f) Install the bonding jumper (6) on the ground stud (19) with washers (4)
and the nut (2).
For Aircraft with MLG door 601R31178 installed
(g) Install the bonding jumper (6) on the MLG door (1) with the bolt (5),
washers (4) and the nut (3).
For all Aircraft
(12) Remove the aircraft from jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 504).
(13) Remove the lockpins from the main landing gear
(Refer to AMM 10- - - 11- - - 00- - - 000- - - 802).
(14) When PART A of this service bulletin is completed, make this entry in the
applicable logbook(s): “Service Bulletin 601R- - - 57- - - 046, Revision C, Wings - - -
Center Wing Primary Structure - - - Cold Working of Fastener Holes in the Main
Landing Gear (MLG) Trunnion Fitting, PART A, incorporated.”

### Page 26

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 25 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of Proximity Sensor PS23GA (PS21GA)
Figure 1
rsb601r32097_016.dg, om, 30/11/04
TARGET
(REF)
MOUNTING
BRACKET
(REF)
1. Nut.
2. Washer.
3. Screw.
4. Clamp.
LEGEND
56.17
(REF)
WS
WS
75.50
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
7. Nut.
8. Proximity sensor
PS23GA (LH)
PS21GA (RH).5. Nut.
6. Lock washer.
5
6
7
8
1
4
2
2
3
3
4
1

### Page 27

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 26 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of Connector P7GA (P6GA)
Figure 2
1. Screw.
2. Washer.
LEGEND
56.177
WS
WS
75.50
ELECTRICAL
HARNESS
3. Connector
1
3
P7GA (LH)
P6GA (RH).
4. Receptacle
J7GA (LH)
J6GA (RH).
4
rsb601r57046_001.dg, mg, 14/09/09
(REF)
2
5
5. Bracket.
PROXIMITY
SENSOR
(REF)
STRUCTURE
(REF)

### Page 28

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 27 of 108
Jul 17/2009
Revision C, Dec 20/2012
Installation of Hi - - -Lites in the MLG Trunnion
Figure 3
1. Left side shown.
NOTE
MLG
TRUNNION
(REF)
rsb601r57046_005.dg mg Aug.25.09
A
A
LOWER
WING PLANK
(REF)
STRAP
(REF)
C
C VIEW LOOKING UP
FASTENER CODE
ITEM NUMBERSYMBOL
6
6
5
6
right side opposite.
LEGEND
1. Hi- -Lite HST411AG8- -16.
2. Hi- -Lite HST411AG10- -11.
3. Hi- -Lite HST411AG10- -13.
4. Hi- -Lite HST411AG10- -14.
5. Collar B0203038- -4.
6. Collar B0203038- -5.
7. Radius washer K601R10004- -5.
3
4
1
2
7
FORWARD
LUG (REF)
B
B
2. For Aircraft 7003- -7010, 7013- -7067,
7069- -7990 and 8000- -8017.

### Page 29

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 28 of 108
Jul 17/2009
Revision C, Dec 20/2012
Cold Working
Figure 4
1. Left side shown,
NOTES
MLG
TRUNNION
(REF)
rsb601r57046_009.dg mg Aug.25.09
A
ALOWER
WING PLANK
(REF)
STRAP
(REF)
C
C
VIEW LOOKING UP
FASTENER CODE
ITEM NUMBERSYMBOL
3
4
right side opposite.
LEGEND
1. Reamer 601R57046K91- -3.
2. Reamer 601R57046K91- -5.
3. Combination gage 601R57046K91- -7.
4. Combination gage 601R57046K91- -9.
5. Sleeve, straight CBS- -10- -2- -N- -16S.
6. Sleeve, straight CBS- -8- -2- -N- -24S.
1
2
FORWARD
LUG (REF)
6
5
B
B
0.2684 to 0.2694 in.
(6.817 to 6.843 mm).
2
0.3305 to 0.3320 in.
(8.395 to 8.433 mm).
3
FTI cold work process STDN 8- -2- -N.4
FTI cold work process STDN 10- -2- -N.5
2 4
3 5
For Aircraft 7003- -7010, 7013- -7067,6.
7069- -7990 and 8000- -8017.

### Page 30

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 29 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of the MLG Doors
Figure 9
rsb601r57046_012.dg, mg, 14/09/09
Right equipment shown,
left equipment opposite.
NOTE
1. MLG door.
2. Nut.
3. Nut.
4. Washer.
5. Bolt.
6. Bonding jumper.
7. Cotter pin.
8. Nut.
9. Washer.
10. Bolt.
11. Rod end.
12. Cotter pin.
13. Door hinge.
14. Nut.
15. Washer.
16. Shim washer.
17. Washer.
18. Pin.
HINGE (REF .)
LEGEND
7
8
9
10
11
1
2
4
4
5
6
12
13
1415
16
17
1716
18
19. Ground stud.
1
3
4
19
6
12
13
1415
16
17
1716
18
FOR AIRCRAFT WITH
DOOR 601R31178 INSTALLED
HINGE (REF .)
FOR AIRCRAFT WITH
DOOR 601R31240 INSTALLED

### Page 31

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 30 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7003 - - -7010, 7013 - - -7067, 7069 - - -7990 and 8000 - - -8017
PART B - - - Cold Work of the Fastener Holes in the Right MLG Trunnion
D. Job S e t --- U p
Reference Information
REFERENCE DESIGNATION
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 1 Put the Aircraft on Jacks
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 4 Removal of the Aircraft from Jacks
A M M 1 0 --- 1 1 --- 0 0 --- 4 0 0 --- 8 0 2Installation of the Main Landing Gear Lockpins
A M M 1 0 --- 1 1 --- 0 0 --- 0 0 0 --- 8 0 2Removal of the Main Landing Gear Lockpins
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 1Pressurize Hydraulic Systems No. 1 and No. 2
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 2Release Hydraulic Pressure - - - Systems No. 1
and No. 2
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 1 Connect External AC Power
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 2 Remove External AC Power
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 2 Lockwire - - - Maintenance Practices
A M M 2 4 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Electrical/Electronic Safety Precautions
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 1 Electrical Extension of the Flaps
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 2 Electrical Retraction of the Flaps
A M M 2 9 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Hydraulic Safety Precautions
NDTM 53- - - 00- - - 097 General Procedure for Inspection of Surface
Cracks in Bolt Holes of Aluminum Alloy Parts
S R M 5 1 --- 2 1 --- 1 1 Corrosion Prevention Procedures
S R M 5 1 --- 2 3 --- 0 0 Pressure, Environment, Fuel Tank and Firewall
Sealing
S R M 5 1 --- 2 4 --- 3 8 Cold Working of Fastener Holes
S R M 5 1 --- 2 5 --- 0 6 Fluid- - -Resistant (FR) Epoxy Primer

### Page 32

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 31 of 108
Jul 17/2009
Revision C, Dec 20/2012
REFERENCE DESIGNATION
S R M 5 1 --- 2 5 --- 1 6 Fluid- - -Resistant (FR) Polyurethane Topcoat
S R M 5 1 --- 2 6 --- 0 0 Cleaning
S R M 5 1 --- 4 0 --- 1 1 How to Prepare Fastener Holes
S R M 5 1 --- 4 2 --- 2 1 Hi- - -Lite Fasteners
(1) Install the lockpins on the main landing gears
(Refer to AMM 10- - - 11- - - 00- - - 400- - - 802).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT . IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions
(Refer to AMM 24- - - 00- - - 00- - - 910- - - 801).
(3) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR:
--- F L I G H T C O N T R O L S
- - - FLIGHT CONTROL SURFACES AND
- - - COMPONENTS THAT MOVE.
MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT ON OR
NEAR THE FLIGHT CONTROL SURFACE. ACCIDENTAL MOVEMENT
OF THE FLIGHT CONTROL CAN CAUSE INJURIES TO PERSON
AND/OR DAMAGE TO EQUIPMENT .
(4) Install the PCU safety tool on the PCU of the inboard ground spoiler as
follows:
WARNING: OBEY ALL THE HYDRAULIC SAFETY PRECAUTIONS WHEN YOU
DO WORK ON ANY HYDRAULIC SYSTEM OR ON A HYDRAULIC
SYSTEM COMPONENT . IF YOU DO NOT OBEY THE SAFETY
PRECAUTIONS, YOU CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE TO EQUIPMENT .

### Page 33

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 32 of 108
Jul 17/2009
Revision C, Dec 20/2012
(a) Obey all the hydraulic safety precautions
(Refer to AMM 29- - - 00- - - 00- - - 910- - - 801).
(b) Pressurize hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 801).
( c ) M a k es u r et h a ty o uh a v et h ec o n d i t i o n st h a tf o l l o wt ol e tt h eg r o u n d
spoilers deploy:
- - - Power levers at IDLE.
--- B o t h W O W c i r c u i t s i n a w e i g h t --- o n --- w h e e l s c o n d i t i o n .
- - - Radio altitude indication at less than five feet.
(d) On the SPOILERS panel, set the GND LIFT DUMPING switch to MAN
ARM. Make sure that the applicable spoiler surfaces extend.
(e) Keep the AC electrical power on and the spoilers in the extended
position.
(f) Release the pressure from hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 802).
(g) When the hydraulic pressure is at zero, disconnect the external AC
power (Refer to AMM 12- - - 00- - - 07- - - 861- - - 802).
(h) Install the PCU safety tool on the PCU on the inboard ground spoiler.
(5) Put the aircraft on jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 801).
(6) Extend the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 801).
(7) On the inboard flap, pull the movable leading- - -edge vane to the flap. This will
l e ty o ug e ta c c e s st ot h ew o r ka r e ao nt h er e a rs p a r .
(8) Use a strap or equivalent to keep the movable leading- - -edge vane retracted.

### Page 34

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 33 of 108
Jul 17/2009
Revision C, Dec 20/2012
(9) Open, safety, and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(10) At WS56.17 and WS75.50, remove nuts (1), screws (3), and washers (2) from
the clamp (4).
(11) If necessary, remove the proximity sensor (8) of the inboard ground spoiler
from the mounting bracket as follows:
(a) Remove nuts (5) and (7) and lock washer (6) from the proximity sensor.
(b) Cover the proximity sensor with a plastic bag to prevent damage.
(c) Move the proximity sensor (8) and electrical harness away from the work
area.
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Post SB 601R - - -27 - - -115 and for Aircraft
7612 and 7645 - - -8017
Refer to Figure 2.
(12) If necessary, between WS56.17 and WS75.50, remove the connector P6GA as
follows:

### Page 35

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 34 of 108
Jul 17/2009
Revision C, Dec 20/2012
(a) Between WS56.17 and WS75.50, remove screws (1) and washers (2)
from the bracket (5).
(b) Remove the lockwire from the connector (3).
(c) On the inboard side of the proximity sensor of the inboard ground
spoiler, disconnect the connector (3) from the receptacle (4).
(d) Install a cap to prevent damage to the connector (3).
(e) Move the electrical harness away from the work area.
For all Aircraft
(13) Remove the access panel that follows from the upper wing surface:
ACCESS PANEL DESCRIPTION
640AT Access Panel
Refer to Figure 9.
(14) Remove the right MLG door (1) as follows:
For Aircraft with MLG door 601R31240 installed
(a) Remove the nut (2), washers (4) and bonding jumper (6) from the
ground stud (19).
For Aircraft with MLG door 601R31178 installed
(b) Remove the nut (3), washers (4), bolt (5) and bonding jumper (6) from
the MLG door (1).
For all Aircraft
(c) Remove and discard the cotter pin (7).
(d) Remove the nut (8), bolt (10) and the washer (9). Disconnect the rod end
(11) from the MLG door (1).
(e) Remove and discard cotter pins (12).
(f) Remove nuts (14), pins (18), washers (15) and (17) and shim washers
(16) from door hinges (13).
(g) Remove the MLG door (1).

### Page 36

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 35 of 108
Jul 17/2009
Revision C, Dec 20/2012
E. Procedure
NOTE: Kits 601R57- - - 046K2, 601R57- - - 046K90 and 601R57- - - 046K91 are
necessary to do the procedure that follows.
Refer to Figure 3.
(1) Remove 23 Hi- - -Lites and collars from the MLG trunnion at the same location
as fasteners (1), (2), (3), and (4) (Refer to SRM 51- - - 42- - - 21).
(2) Make sure that you use the applicable clamping method to hold the strap, the
lower wing plank and the MLG trunnion together.
Refer to Figure 3 and 4.
(3) Cold work a hole for installation of Hi- - -Lite (1) in the MLG trunnion as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 8- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open one hole to a diameter between 0.2684 in. and 0.2694 in. (6.817
mm and 6.843 mm) with the reamer (P/N 601R57046K91- - - 3).
(b) Do an eddy current inspection of the fastener hole
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 7), make sure the
fastener hole has a diameter of 0.2684 in. to 0.2694 in. (6.817 mm to
6.843 mm).
(e) Before cold working, enlarge the countersink of the fastener hole
sufficiently to receive the Hi- - -Lite (1).
(f) Cold work one hole in the MLG trunnion, the strap and the lower wing
plank (Refer to SRM 51- - - 24- - - 38).

### Page 37

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 36 of 108
Jul 17/2009
Revision C, Dec 20/2012
NOTE: U s e s t r a i g h t s l e e v e C B S --- 8 --- 2 --- N --- 2 4 S .
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 8 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 8- - - 2- - - N- - - 1- - - .2780), ream the
fastener hole to a final diameter of 0.2775 in. to 0.2792 in. (7.049 mm to
7.092 mm).
(4) Cold work 22 holes for installation of Hi- - -Lites (2), (3) and (4) in the MLG
trunnion as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 10- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open 22 holes to a diameter between 0.3305 in. and 0.3320 in. (8.395
mm and 8.433 mm) with the reamer (P/N 601R57046K91- - - 5).
(b) Do an eddy current inspection of the fastener holes
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 9), make sure the
fastener holes have a diameter of 0.3305 in. to 0.3320 in. (8.395 mm to
8.433 mm).
(e) Before cold working, enlarge the countersinks of the fastener holes
sufficiently to receive Hi- - -Lites (2), (3) and (4).
(f) Cold work 22 holes in the MLG trunnion (Refer to SRM 51- - - 24- - - 38).

### Page 38

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 37 of 108
Jul 17/2009
Revision C, Dec 20/2012
NOTE: S t r a i g h t s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 2 S a r e n e c e s s a r y t o d o t h e
cold work through lower wing plank and MLG trunnion. Straight
s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 6 S a r e n e c e s s a r y t o d o t h e c o l d w o r k
through the trunnion strap, lower wing plank and MLG trunnion.
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 1 0 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 10- - - 2- - - N- - - 1- - - .3405), ream the
fastener holes to a final diameter of 0.3400 in. to 0.3417 in. (8.636 mm to
8.679 mm).
(5) Make sure that the countersinks have no ridge(s).
(6) If ridge(s) is/are found, manually remove the ridge(s) with a countersink tool.
(7) Apply chemical conversion coating or equivalent in the fastener holes
( R e f e r t o S R M 5 1 --- 2 1 --- 1 1 ) .
( 8 ) W e t --- i n s t a l l H i --- L i t e s ( 2 ) a n d c o l l a r s ( 6 ) t h r o u g h t h e l o w e r w i n g p l a n k a n d t h e
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(9) Prepare the radius washer (7) as follows:
(a) Open the hole in the radius washer (7) to a diameter of 0.348
- - - 0.001/+0.006 in. (8.84 - - - 0.03/+0.15 mm).
(b) T emporarily put the radius washer (7) in position on the inner side of the
aft flange of the MLG trunnion.
(c) Make sure that the radius washer (7) sits correctly in the radius.
(d) If necessary, remove unwanted material on the radius washer (7) to get a
correct installation.
(e) Make sure that you keep a minimum edge distance of 0.9D.
(f) Apply chemical conversion coating on the bare metal areas
(Refer to 51- - - 21- - - 11).
(g) Apply one layer of primer in the fastener hole (Refer to SRM 51- - - 25- - - 06).
(10) Install the radius washer (7) with faying surface sealant and wet- - - install the
Hi- - - Lite (3) and collar (6) through the lower wing plank and MLG trunnion
( R e f e r t o S R M 5 1 --- 2 3 --- 0 0 a n d S R M 5 1 --- 4 2 --- 2 1 ) .
(11) Wet- - -install Hi- - -Lites (4) and collars (6) through the strap, lower wing plank
and MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).

### Page 39

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 38 of 108
Jul 17/2009
Revision C, Dec 20/2012
(12) Wet- - - install Hi- - - Lite (1) and collar (5) through the strap, lower wing plank and
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(13) Apply a layer of epoxy primer on Hi- - - Lites (1), (2), (3) and (4) and collars (5)
and (6) (Refer to SRM 51- - - 25- - - 06).
(14) Apply a layer of polyurethane topcoat on Hi- - - Lites (1), (2), (3) and (4) and
collars (5) and (6) (Refer to SRM 51- - - 25- - - 16).
(15) Do the identification of the MLG trunnion as follows:
(a) If a MLG trunnion was repaired or replaced, speak with a representative
of the Customer Response Centre (CRC) at 514- - - 855- - - 8500 for an
identification number.
For Aircraft 7003 - - -7010, 7013 - - -7067 and 7069 - - -7138 Pre-REO 601R - - -57 - - -21 - - -003 and
Pre-SB 601R - - -32 - - -054
(b) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 2.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .
For Aircraft 7003 - - -7010, 7013 - - -7067 and 7069 - - -7138 Post-REO 601R - - -57 - - -21 - - -003 or
Post-SB 601R - - -32 - - -054
(c) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 4.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .

### Page 40

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 39 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7139 - - -7990 and 8000 - - -8017
(d) If service bulletins 601R- - - 57- - - 046, 601R- - - 57- - - 047 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 4.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .
F. C l o s e Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Install the access panel that follows on the upper wing surface:
ACCESS PANEL DESCRIPTION
640AT Access Panel
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(3) If removed, install the proximity sensor (8) of the inboard ground spoiler as
follows:
(a) Install the proximity sensor (8) of the inboard ground spoiler on the
mounting bracket with the lock washer (6) and nuts (5) and (7).
(b) Adjust the position of the proximity sensor (8). Make sure there is a
clearance of 0.035 to 0.055 in. (0.89 to 1.40 mm) between the proximity
sensor (8) and the target.
(c) Safety the proximity sensor (8) with lockwire.
(4) At WS56.17 and WS75.50, install clamps (4), screws (3), washers (2) and nuts
(1) to keep the electrical harness in position.

### Page 41

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 40 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7003 - - -7010, 7013 - - -7611, 7613 - - -7644 Post SB 601R - - -27 - - -115 and for Aircraft
7612 and 7645 - - -8017
Refer to Figure 2.
(5) If removed, between WS56.17 and WS75.50, install the connector P6GA as
follows:
(a) Between WS56.17 and WS75.50, install the bracket (5) with screws (1)
and washers (2).
(b) At WS67.25, connect the connector (3) to the receptacle (4).
(c) Safety the connector (3) with lockwire.
For all Aircraft
(6) Remove the PCU safety tool from the PCU of the inboard ground spoiler.
(7) Remove the strap on the flap to extend the movable leading- - - edge vane.
(8) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
(9) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
(10) Retract the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 802).

### Page 42

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 41 of 108
Jul 17/2009
Revision C, Dec 20/2012
Refer to Figure 9.
(11) Install the right MLG door (1) as follows:
(a) Install pins (18) through door hinges (13) with washers (15) and (17),
shim washers (16) and nuts (14).
(b) T orque the nuts (14) to a maximum of 20 lbf Sin (2.26 NS m).
(c) Safety the nuts (14) with cotter pins (12).
(d) Attach the rod end (11) to the MLG door (1) with the bolt (10), washer (9)
and the nut (8).
(e) Safety the nut (8) with the cotter pin (7).
For Aircraft with MLG door 601R31240 installed
(f) Install the bonding jumper (6) on the ground stud (19) with washers (4)
and nut (2).
For Aircraft with MLG door 601R31178 installed
(g) Install the bonding jumper (6) on the MLG door (1) with the bolt (5),
washers (4) and the nut (3).
For all Aircraft
(12) Remove the aircraft from jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 504).
(13) Remove the lockpins from the main landing gear
(Refer to AMM 10- - - 11- - - 00- - - 000- - - 802).
(14) When PART B of this service bulletin is completed, make this entry in the
applicable logbook(s): “Service Bulletin 601R- - - 57- - - 046, Revision C, Wings - - -
Center Wing Primary Structure - - - Cold Working of Fastener Holes in the Main
Landing Gear (MLG) Trunnion Fitting, PART B, incorporated.”

### Page 43

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 42 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft 7011 and 7012
PART C - - - Cold Work of the Fastener Holes in the Left MLG Trunnion
G. Job S e t --- U p
Reference Information
REFERENCE DESIGNATION
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 1 Put the Aircraft on Jacks
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 4 Removal of the Aircraft from Jacks
A M M 1 0 --- 1 1 --- 0 0 --- 4 0 0 --- 8 0 2Installation of the Main Landing Gear Lockpins
A M M 1 0 --- 1 1 --- 0 0 --- 0 0 0 --- 8 0 2Removal of the Main Landing Gear Lockpins
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 1Pressurize Hydraulic Systems No. 1 and No. 2
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 2Release Hydraulic Pressure - - - Systems No. 1
and No. 2
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 1 Connect External AC Power
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 2 Remove External AC Power
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 2 Lockwire - - - Maintenance Practices
A M M 2 4 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Electrical/Electronic Safety Precautions
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 1 Electrical Extension of the Flaps
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 2 Electrical Retraction of the Flaps
A M M 2 9 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Hydraulic Safety Precautions
NDTM 53- - - 00- - - 097 General Procedure for Inspection of Surface
Cracks in Bolt Holes of Aluminum Alloy Parts
S R M 5 1 --- 2 1 --- 1 1 Corrosion Prevention Procedures
S R M 5 1 --- 2 3 --- 0 0 Pressure, Environment, Fuel Tank and Firewall
Sealing
S R M 5 1 --- 2 4 --- 3 8 Cold Working of Fastener Holes
S R M 5 1 --- 2 5 --- 0 6 Fluid- - -Resistant (FR) Epoxy Primer

### Page 44

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 43 of 108
Jul 17/2009
Revision C, Dec 20/2012
REFERENCE DESIGNATION
S R M 5 1 --- 2 5 --- 1 6 Fluid- - -Resistant (FR) Polyurethane Topcoat
S R M 5 1 --- 2 6 --- 0 0 Cleaning
S R M 5 1 --- 4 0 --- 1 1 How to Prepare Fastener Holes
S R M 5 1 --- 4 2 --- 2 1 Hi- - -Lite Fasteners
(1) Install the lockpins on the main landing gears
(Refer to AMM 10- - - 11- - - 00- - - 400- - - 802).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT . IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions
(Refer to AMM 24- - - 00- - - 00- - - 910- - - 801).
(3) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR:
--- F L I G H T C O N T R O L S
- - - FLIGHT CONTROL SURFACES AND
- - - COMPONENTS THAT MOVE.
MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT ON OR
NEAR THE FLIGHT CONTROL SURFACE. ACCIDENTAL MOVEMENT
OF THE FLIGHT CONTROL CAN CAUSE INJURIES TO PERSON
AND/OR DAMAGE TO EQUIPMENT .
(4) Install the PCU safety tool on the PCU on the inboard ground spoiler as
follows:
WARNING: OBEY ALL THE HYDRAULIC SAFETY PRECAUTIONS WHEN YOU
DO WORK ON ANY HYDRAULIC SYSTEM OR ON A HYDRAULIC
SYSTEM COMPONENT . IF YOU DO NOT OBEY THE SAFETY
PRECAUTIONS, YOU CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE TO EQUIPMENT .

### Page 45

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 44 of 108
Jul 17/2009
Revision C, Dec 20/2012
(a) Obey all the hydraulic safety precautions
(Refer to AMM 29- - - 00- - - 00- - - 910- - - 801).
(b) Pressurize hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 801).
( c ) M a k es u r et h a ty o uh a v et h ec o n d i t i o n st h a tf o l l o wt ol e tt h eg r o u n d
spoilers deploy:
1 Power levers at IDLE.
2 Both WOW circuits in a weight- - -on- - -wheels condition.
3 Radio altitude indication at less than five feet.
(d) On the SPOILERS panel, set the GND LIFT DUMPING switch to MAN
ARM. Make sure that the applicable spoiler surfaces extend.
(e) Keep the AC electrical power on and the spoilers in the extended
position.
(f) Release the pressure from hydraulic system No. 1 and No. 2
(Refer to AMM 12- - - 00- - - 06- - - 863- - - 802).
(g) When the hydraulic pressure is at zero, disconnect the external AC
power (Refer to AMM 12- - - 00- - - 07- - - 861- - - 802).
(h) Install the PCU safety tool on the PCU of the inboard ground spoiler.
(5) Put the aircraft on jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 801).
(6) Extend the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 801).
(7) On the inboard flap, pull the movable leading- - -edge vane to the flap. This will
l e ty o ug e ta c c e s st ot h ew o r ka r e ao nt h er e a rs p a r .
(8) Use a strap or equivalent to keep the movable leading- - -edge vane retracted.

### Page 46

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 45 of 108
Jul 17/2009
Revision C, Dec 20/2012
(9) Open, safety, and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
For Aircraft 7011 and 7012 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(10) At WS56.17 and WS75.50, remove nuts (1), screws (3), and washers (2) from
the clamp (4).
(11) Remove the proximity sensor (8) of the inboard ground spoiler from the
mounting bracket as follows:
(a) Remove nuts (5) and (7) and the lock washer (6) from the proximity
sensor.
(b) Cover the proximity sensor with a plastic bag to prevent damage.
(c) Move the proximity sensor (8) and electrical harness away from the work
area.
For Aircraft 7011 and 7012 Post SB 601R - - -27 - - -115
Refer to Figure 2.
(12) Between WS56.17 and WS75.50, remove screws (1) and washers (2) from the
bracket (5).

### Page 47

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 46 of 108
Jul 17/2009
Revision C, Dec 20/2012
(13) Remove the lockwire from the connector (3).
(14) On the inboard side of the proximity sensor of the inboard ground spoiler,
disconnect the connector (3) from the receptacle (4).
(15) Install a cap to prevent damage to the connector (3).
(16) Move the electrical harness away from the work area.
For all Aircraft
(17) Remove the access panel that follows from the upper wing surface:
ACCESS PANEL DESCRIPTION
540AT Access Panel
Refer to Figure 9.
(18) Remove the left MLG door (1) as follows:
For Aircraft with MLG door 601R31240 installed
(a) Remove the nut (2), washers (4) and bonding jumper (6) from the
ground stud (19).
For Aircraft with MLG door 601R31178 installed
(b) Remove the nut (3), washers (4), bolt (5) and bonding jumper (6) from
the MLG door (1).
For all Aircraft
(c) Remove and discard the cotter pin (7).
(d) Remove the nut (8), bolt (10) and the washer (9). Disconnect the rod end
(11) from the MLG door (1).
(e) Remove and discard cotter pins (12).
(f) Remove nuts (14), pins (18), washers (15) and (17) and shim washers
(16) from door hinges (13).
(g) Remove the MLG door (1).

### Page 48

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 47 of 108
Jul 17/2009
Revision C, Dec 20/2012
H. Procedure
NOTE: Kits 601R57- - - 046K3, 601R57- - - 046K90 and 601R57- - - 046K91 are
necessary to do the procedure that follows.
Refer to Figure 5.
( 1 ) R e m o v e1 2H i - - - L i t e sa n dc o l l a r si n b o a r df r o mt h eM L Gb a yo nt h ee d g eo ft h e
MLG trunnion at the same location as fasteners (1), (2) and (3) (Refer to SRM
51- - - 42- - - 21).
(2) Make sure that you use the applicable clamping method to hold the strap, the
lower wing plank and the MLG trunnion together.
Refer to Figure 5 and 6.
(3) Cold work a hole for installation of Hi- - -Lite (1) in the MLG trunnion as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 8- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open a hole to a diameter between 0.2684 in. and 0.2694 in. (6.817 mm
and 6.843 mm) with the reamer (P/N 601R57046K91- - - 3).
(b) Do an eddy current inspection of the fastener hole
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 7), make sure the
fastener hole has a diameter of 0.2684 in. to 0.2694 in. (6.817 mm to
6.843 mm).
(e) Before cold working, enlarge the countersink of the fastener hole
sufficiently to receive the Hi- - -Lite (1).
(f) Cold work a hole in the MLG trunnion, the strap and the lower wing
plank (Refer to SRM 51- - - 24- - - 38).

### Page 49

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 48 of 108
Jul 17/2009
Revision C, Dec 20/2012
NOTE: U s e s t r a i g h t s l e e v e C B S --- 8 --- 2 --- N --- 2 4 S .
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 8 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 8- - - 2- - - N- - - 1- - - .2780), ream the
fastener hole to a final diameter of 0.2775 in. to 0.2792 in. (7.049 mm to
7.092 mm).
(4) Cold work 11 holes for installation of Hi- - -Lites (2) and (3) in the MLG trunnion
as follows:
NOTE: Low expansion cold work process will be used. Some values are
different than those given by Fatigue Technology Inc (FTI).
NOTE: Use the standard tool diameter number (STDN) 10- - -2- - -N.
NOTE: If you already have second oversize fasteners or larger installed in the
MLG trunnion, speak with a representative of the Customer Response
Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail at
thd.crj@aero.bombardier .com for a disposition.
CAUTION: MAKE SURE TO USE SUFFICIENT PROTECTION ON THE MLG
FITTING WHEN YOU REAM THE HOLE(S). IF YOU DO NOT DO
THIS, YOU CAN CAUSE DAMAGE TO THE MLG FITTING.
(a) Open 11 holes to a diameter between 0.3305 in. and 0.3320 in. (8.395
mm and 8.433 mm) with the reamer (P/N 601R57046K91- - - 5).
(b) Do an eddy current inspection of the fastener holes
(Refer to NDTM 53- - - 00- - - 097).
(c) If there is damage, speak with a representative of the Customer
Response Center (CRC) at phone number 514- - - 855- - - 8500 or by e- - - mail
at thd.crj@aero.bombardier .com for a disposition.
(d) With the combination gauge (P/N 601R57046K91- - - 9), make sure the
fastener holes have a diameter of 0.3305 in. to 0.3320 in. (8.395 mm to
8.433 mm).
(e) Before cold working, enlarge the countersinks of the fastener holes
sufficiently to receive Hi- - -Lites (2) and (3).
(f) Cold work 11 holes in the MLG trunnion, the strap and the lower wing
plank (Refer to SRM 51- - - 24- - - 38).
NOTE: S t r a i g h t s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 2 S a r e n e c e s s a r y t o d o t h e
cold work through lower wing plank and MLG trunnion. Straight
s l e e v e s C B S --- 1 0 --- 2 --- N --- 1 6 S a r e n e c e s s a r y t o d o t h e c o l d w o r k
through the trunnion strap, lower wing plank and MLG trunnion.

### Page 50

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 49 of 108
Jul 17/2009
Revision C, Dec 20/2012
(g) Make sure that the split in the sleeve points inboard or outboard.
( h ) W i t h t h e c o m b i n a t i o n g a u g e ( C B G --- 1 0 --- 2 --- N --- 1 ) , m a k e s u r e t h e h o l e i s
cold-worked.
(i) With the gauge finish reamer (CBR- - - 10- - - 2- - - N- - - 1- - - .3405), ream the
fastener holes to a final diameter of 0.3400 in. to 0.3417 in. (8.636 mm to
8.679 mm).
(5) Make sure that the countersinks have no ridge(s).
(6) If ridge(s) is/are found, manually remove the ridge(s) with a countersink tool.
(7) Apply chemical conversion coating or equivalent in the fastener holes
( R e f e r t o S R M 5 1 --- 2 1 --- 1 1 ) .
(8) Wet- - - install Hi- - - Lite (2) and collar (5) through the lower wing plank and the
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(9) Wet- - -install Hi- - -Lites (3) and collars (5) through the strap, lower wing plank
and MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(10) Wet- - - install Hi- - - Lite (1) and collar (4) through the strap, lower wing plank and
MLG trunnion (Refer to SRM 51- - - 23- - - 00 and SRM 51- - - 42- - - 21).
(11) Apply a layer of epoxy primer on Hi- - - Lites (1), (2) and (3) and collars (4) and
(5) (Refer to SRM 51- - - 25- - - 06).
(12) Apply a layer of polyurethane topcoat on Hi- - - Lites (1), (2) and (3) and collars
(4) and (5) (Refer to SRM 51- - - 25- - - 16).
(13) Do the identification of the MLG trunnion as follows:
(a) If an MLG trunnion was repaired or replaced, speak with a representative
of the Customer Response Centre (CRC) at 514- - - 855- - - 8500 for an
identification number.
(b) If service bulletins 601R- - - 32- - - 097, 601R- - - 57- - - 046 and 601R- - - 57- - - 048
have been incorporated, do as follows:
1 Clean the identification areas with solvent
( r e f e r t o S R M 5 1 --- 2 6 --- 0 0 ) .
2 Identify the MLG trunnion as K601R10032- - - 9.
3 Apply a layer of clear polyurethane topcoat on the identifications
( r e f e r t o S R M 5 1 --- 2 5 --- 1 6 ) .

### Page 51

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 50 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of Proximity Sensor PS23GA (PS21GA)
Figure 1
rsb601r32097_016.dg, om, 30/11/04
TARGET
(REF)
MOUNTING
BRACKET
(REF)
1. Nut.
2. Washer.
3. Screw.
4. Clamp.
LEGEND
56.17
(REF)
WS
WS
75.50
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
ELECTRICAL
HARNESS
7. Nut.
8. Proximity sensor
PS23GA (LH)
PS21GA (RH).5. Nut.
6. Lock washer.
5
6
7
8
1
4
2
2
3
3
4
1

### Page 52

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 51 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of Connector P7GA (P6GA)
Figure 2
1. Screw.
2. Washer.
LEGEND
56.177
WS
WS
75.50
ELECTRICAL
HARNESS
3. Connector
1
3
P7GA (LH)
P6GA (RH).
4. Receptacle
J7GA (LH)
J6GA (RH).
4
rsb601r57046_001.dg, mg, 14/09/09
(REF)
2
5
5. Bracket.
PROXIMITY
SENSOR
(REF)
STRUCTURE
(REF)

### Page 53

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 52 of 108
Jul 17/2009
Revision C, Dec 20/2012
Installation of Hi - - -Lites in the MLG Trunnion
Figure 5
rsb601r57046_006.dg mg Aug.25.09
C VIEW LOOKING UP
MLG
TRUNNION
(REF)
A
A
LOWER
WING PLANK
(REF)
STRAP
(REF)
C
FASTENER CODE
ITEM NUMBERSYMBOL
5
4
5
LEGEND
1. Hi- -Lite pin HST411AG8- -16.
2. Hi- -Lite pin HST411AG10- -11.
3. Hi- -Lite pin HST411AG10- -14.
4. Collar B0203038- -4.
5. Collar B0203038- -5.
3
1
2
FORWARD
LUG (REF)
B
B
1. Left side shown.
NOTE
right side opposite.
2. For Aircraft 7011 and 7012.

### Page 54

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 53 of 108
Jul 17/2009
Revision C, Dec 20/2012
Cold Working
Figure 6
1. Left side shown,
NOTES
MLG
TRUNNION
(REF)
rsb601r57046_009.dg mg Aug.25.09
A
ALOWER
WING PLANK
(REF)
STRAP
(REF)
C
C
VIEW LOOKING UP
FASTENER CODE
ITEM NUMBERSYMBOL
3
4
right side opposite.
LEGEND
1. Reamer 601R57046K91- -3.
2. Reamer 601R57046K91- -5.
3. Combination gage 601R57046K91- -7.
4. Combination gage 601R57046K91- -9.
5. Sleeve, straight CBS- -10- -2- -N- -16S.
6. Sleeve, straight CBS- -8- -2- -N- -24S.
1
2
FORWARD
LUG (REF)
6
5
B
B
0.2684 to 0.2694 in.
(6.817 to 6.843 mm).
2
0.3305 to 0.3320 in.
(8.395 to 8.433 mm).
3
FTI cold work process STDN 8- -2- -N.4
FTI cold work process STDN 10- -2- -N.5
2 4
3 5
For Aircraft 7011 and 7012.6.

### Page 55

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 54 of 108
Jul 17/2009
Revision C, Dec 20/2012
Removal/Installation of the MLG Doors
Figure 9
rsb601r57046_012.dg, mg, 14/09/09
Right equipment shown,
left equipment opposite.
NOTE
1. MLG door.
2. Nut.
3. Nut.
4. Washer.
5. Bolt.
6. Bonding jumper.
7. Cotter pin.
8. Nut.
9. Washer.
10. Bolt.
11. Rod end.
12. Cotter pin.
13. Door hinge.
14. Nut.
15. Washer.
16. Shim washer.
17. Washer.
18. Pin.
HINGE (REF .)
LEGEND
7
8
9
10
11
1
2
4
4
5
6
12
13
1415
16
17
1716
18
19. Ground stud.
1
3
4
19
6
12
13
1415
16
17
1716
18
FOR AIRCRAFT WITH
DOOR 601R31178 INSTALLED
HINGE (REF .)
FOR AIRCRAFT WITH
DOOR 601R31240 INSTALLED

### Page 56

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 55 of 108
Jul 17/2009
Revision C, Dec 20/2012
I. Close Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) Install the access panel that follows on the upper wing surface:
ACCESS PANEL DESCRIPTION
540AT Access Panel
For Aircraft 7011 and 7012 Pre SB 601R - - -27 - - -115
Refer to Figure 1.
(3) Install the proximity sensor (8) of the inboard ground spoiler as follows:
(a) Install the proximity sensor (8) of the inboard ground spoiler on the
mounting bracket with the lock washer (6) and nuts (5) and (7).
(b) Adjust the position of the proximity sensor (8). Make sure there is a
clearance of 0.035 to 0.055 in. (0.89 to 1.40 mm) between the proximity
sensor (8) and the target.
(c) Safety the proximity sensor (8) with lockwire.
(4) At WS56.17 and WS75.50, install clamps (4), screws (3), washers (2) and nuts
(1) to keep the electrical harness in position.
For Aircraft 7011 and 7012 Post SB 601R - - -27 - - -115
Refer to Figure 2.
(5) Between WS56.17 and WS75.50, install the bracket (5) with screws (1) and
washers (2).
(6) At WS67.25, connect the connector (3) to the receptacle (4).
(7) Safety the connector (3) with lockwire.
For all Aircraft
(8) Remove the PCU safety tool from the PCU of the inboard ground spoiler.
(9) Remove the strap on the flap to extend the movable leading- - - edge vane.

### Page 57

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 56 of 108
Jul 17/2009
Revision C, Dec 20/2012
(10) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
C B P --- 1 A2 HYD PUMP 3B 221
C B P --- 1 A5 HYD PUMP 2 221
C B P --- 1 F4 FLAPS CONT CH 1 221
C B P --- 1 G11 H Y DS Y S TA CP U M PC O N T3 B 221
C B P --- 1 G14 H Y DS Y S TA CP U M PC O N T2 221
C B P --- 2 A2 HYD PUMP 3A 222
C B P --- 2 A5 HYD PUMP 1 222
C B P --- 2 F4 FLAPS CONT CH 2 222
C B P --- 2 G14 H Y DS Y S TA CP U M PC O N T1 222
C B P --- 2 G15 H Y DS Y S TA CP U M PC O N T3 A 222
(11) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
(12) Retract the flaps (Refer to AMM 27- - - 54- - - 00- - - 866- - - 802).
Refer to Figure 9.
(13) Install the left MLG door (1) as follows:
(a) Install pins (18) through door hinges (13) with washers (15) and (17),
shim washers (16) and nuts (14).
(b) T orque the nuts (14) to a maximum of 20 lbf Sin (2.26 NS m).
(c) Safety the nuts (14) with cotter pins (12).
(d) Attach the rod end (11) to the MLG door (1) with the bolt (10), washer (9)
and the nut (8).
(e) Safety the nut (8) with the cotter pin (7).

### Page 58

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 57 of 108
Jul 17/2009
Revision C, Dec 20/2012
For Aircraft with MLG door 601R31240 installed
(f) Install the bonding jumper (6) on the ground stud (19) with washers (4)
and nut (2).
For Aircraft with MLG door 601R31178 installed
(g) Install the bonding jumper (6) on the MLG door (1) with the bolt (5),
washers (4) and the nut (3).
For all Aircraft
(14) Remove the aircraft from jacks (Refer to AMM 07- - - 11- - - 01- - - 582- - - 504).
(15) Remove the lockpins from the main landing gear
(Refer to AMM 10- - - 11- - - 00- - - 000- - - 802).
(16) When PART C of this service bulletin is completed, make this entry in the
applicable logbook(s): “Service Bulletin 601R- - - 57- - - 046, Revision C, Wings - - -
Center Wing Primary Structure - - - Cold Working of Fastener Holes in the Main
Landing Gear (MLG) Trunnion Fitting PART C, incorporated.”

### Page 59

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 58 of 108
Jul 17/2009
Revision C, Dec 20/2012
PART D - - - Cold Work of the Fastener Holes in the Right MLG Trunnion
For Aircraft 7011 and 7012
J. Job S e t --- U p
Reference Information
REFERENCE DESIGNATION
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 1 Put the Aircraft on Jacks
A M M 0 7 --- 1 1 --- 0 1 --- 5 8 2 --- 8 0 4 Removal of the Aircraft from Jacks
A M M 1 0 --- 1 1 --- 0 0 --- 4 0 0 --- 8 0 2Installation of the Main Landing Gear Lockpins
A M M 1 0 --- 1 1 --- 0 0 --- 0 0 0 --- 8 0 2Removal of the Main Landing Gear Lockpins
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 1Pressurize Hydraulic Systems No. 1 and No. 2
A M M 1 2 --- 0 0 --- 0 6 --- 8 6 3 --- 8 0 2Release Hydraulic Pressure - - - Systems No. 1
and No. 2
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 1 Connect External AC Power
A M M 1 2 --- 0 0 --- 0 7 --- 8 6 1 --- 8 0 2 Remove External AC Power
A M M 2 0 --- 2 4 --- 0 0 --- 9 1 0 --- 8 0 2 Lockwire - - - Maintenance Practices
A M M 2 4 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Electrical/Electronic Safety Precautions
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 1 Electrical Extension of the Flaps
A M M 2 7 --- 5 4 --- 0 0 --- 8 6 6 --- 8 0 2 Electrical Retraction of the Flaps
A M M 2 9 --- 0 0 --- 0 0 --- 9 1 0 --- 8 0 1 Hydraulic Safety Precautions
NDTM 53- - - 00- - - 097 General Procedure for Inspection of Surface
Cracks in Bolt Holes of Aluminum Alloy Parts
S R M 5 1 --- 2 1 --- 1 1 Corrosion Prevention Procedures
S R M 5 1 --- 2 3 --- 0 0 Pressure, Environment, Fuel Tank and Firewall
Sealing
S R M 5 1 --- 2 4 --- 3 8 Cold Working of Fastener Holes
S R M 5 1 --- 2 5 --- 0 6 Fluid- - -Resistant (FR) Epoxy Primer
S R M 5 1 --- 2 5 --- 1 6 Fluid- - -Resistant (FR) Polyurethane Topcoat

### Page 60

SERVICE BULLETIN 601R- - -57- - -046
SB 601R- - - 57- - - 046
Page 59 of 108
Jul 17/2009
Revision C, Dec 20/2012
REFERENCE DESIGNATION
S R M 5 1 --- 2 6 --- 0 0 Cleaning
S R M 5 1 --- 4 0 --- 1 1 How to Prepare Fastener Holes
S R M 5 1 --- 4 2 --- 2 1 Hi- - -Lite Fasteners
(1) Install the lockpins on the main landing gears
(Refer to AMM 10- - - 11- - - 00- - - 400- - - 802).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT . IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions
(Refer to AMM 24- - - 00- - - 00- - - 910- - - 801).
(3) Apply electrical power to the aircraft (Refer to AMM 12- - - 00- - - 07- - - 861- - - 801).
WARNING: PUT THE SAFETY DEVICES, THE WARNING SIGNS, AND THE
WARNING PLACARDS IN POSITION BEFORE YOU START A
PROCEDURE ON OR NEAR:
--- F L I G H T C O N T R O L S
- - - FLIGHT CONTROL SURFACES AND
- - - COMPONENTS THAT MOVE.
MAKE SURE THAT THERE ARE NO PERSONS OR EQUIPMENT ON OR
NEAR THE FLIGHT CONTROL SURFACE. ACCIDENTAL MOVEMENT
OF THE FLIGHT CONTROL CAN CAUSE INJURIES TO PERSON
AND/OR DAMAGE TO EQUIPMENT .
(4) Install the PCU safety tool on the PCU of the inboard ground spoiler as
follows:
WARNING: OBEY ALL THE HYDRAULIC SAFETY PRECAUTIONS WHEN YOU
DO WORK ON ANY HYDRAULIC SYSTEM OR ON A HYDRAULIC
SYSTEM COMPONENT . IF YOU DO NOT OBEY THE SAFETY
PRECAUTIONS, YOU CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE TO EQUIPMENT .
(a) Obey all the hydraulic safety precautions
(Refer to AMM 29- - - 00- - - 00- - - 910- - - 801).

The text continues at https://openairdocs.org/service-documents/bombardier/601r-57-046/file/7cf85120c119.md?from=61

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
