# MHI RJ Service Bulletin 670BA-32-062: Revision A

- Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-0885; AD 2022-21-10 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [MHI RJ Service Bulletin 670BA-32-062](https://openairdocs.org/service-documents/bombardier/670ba-32-062.md)
- Title as filed: 670BA-32-062A
- Pages: 33
- PDF: https://openairdocs.org/files/sha256/7b/4f/7b4fcd079ca3a1182f04144a96ed84a4dd1d603e856ff58dc809fd24d958b2c6
- Page: https://openairdocs.org/service-documents/bombardier/670ba-32-062/file/7b4fcd079ca3

## Text

Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SB 670BA−32−062
Page 1 of 2
Dec 02/2021
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
SERVICE BULLETIN 670BA−32−062
SUBJECT:  Landing Gear − Landing Gear System, General − Inspection of Landing
Gear Component(s) Maintenance Documentation and, if required, removal
of affected component(s) from service for overhaul
These Pages transmit:
Revision A of Service Bulletin 670BA−32−062, dated Dec 02/2021
and
Initial issue of Appendix A, dated Dec 02/2021.
The changes in this revision have no effect on aircraft that have had
this service bulletin incorporated.
Reason:
Revised Planning Information, paragraph 1., to:
Give more information and add notes in the Reason section.
Divide the existing PART B (removal, restoration and installation of the components)
into separate PARTS for the removal, the restoration and the installation of the NLG,
the left MLG and the right MLG to agree with Transport Canada Airworthiness
Directive (AD). The AD will only mandate the removal and installation of the affected
components.
Move the Component Calendar Age from the Procedure section to the Compliance
section.
Change the contact information of the Customer Response Center (CRC) Support
Team.
Revised Accomplishment Instructions, paragraph 2., to:
Remove some notes that are not applicable to the Job set−Up and Close−Out
sections.
Changed the title of PART B from /quoteblleftRemoval of the Landing gear Component for
Overhaul" to /quoteblleftRemoval of the NLG Component(s) from the Aircraft.
Add PART C −Overhaul of the NLG Component(s)
Add PART D − Installation of Serviceable NLG Component(s) on the Aircraft
Add PART E − Removal of the Left MLG Component(s) from the Aircraft

### Page 2

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 2 of 2
Dec 02/2021
Add PART F −Overhaul of the Left MLG Component(s)
Add PART G −Installation of Serviceable Left MLG Component(s) on the Aircraft
Add PART H − Removal of the Right MLG Component(s) from the Aircraft
Add PART I −Overhaul of the right MLG Component(s)
Add PART J − Installation of Serviceable Right MLG Component(s) on the Aircraft
Change the contact information of the Customer Response Center (CRC) Support
Team.
Add Appendix A to:
Facilitate component tracking.
This revision also includes small editorial changes that do not have an effect on the technical
content.
Instructions:  
Discard the copy of Service Bulletin 670BA−32−062, dated Dec 14/2020. Replace with
the copy attached.
Service Bulletin History:  
Initial issue, dated Dec 14/ 2020
1

### Page 3

SB 670BA−32−062
Page 1 of 29
Dec 14/2020
Revision A, Dec 02/2021
SERVICE BULLETIN
Technical
Publications
THIS SERVICE BULLETIN IS SENT TO EACH OPERATOR. IF THE OPERATOR HAS LEASED AIRCRAFT ,
TRANSFERRED SPARES IN THE LAST SIX MONTHS, SEND THIS SERVICE BULLETIN TO THE NEW
OWNER, UNLESS CONFIRMATION WAS RECEIVED THAT MHIRJ HAS INCLUDED THE NEW
OPERATOR ON THE DISTRIBUTION LIST .
SEND THIS SERVICE BULLETIN TO THE LESSEE. IF THE OPERATOR HAS SOLD AIRCRAFT OR
ATA SYSTEM: 32−00 NUMBER: 670BA−32−062
SUBJECT:  Landing Gear − Landing Gear System, General − Inspection of Landing
Gear Component(s) Maintenance Documentation and, if Required,
Removal of Affected Component(s) from Service for Overhaul
1. PLANNING INFORMATION
A. Effectivity
(1) Aircraft Affected:
AIRCRAFT
MODEL
SERVICE AIRCRAFT
SERIAL NUMBERS
PRODUCTION
AIRCRAFT
SERIAL NUMBERS
CL−600−2C10
and/or
CL−600−2C11
10002 thru 10999. [1]
CL−600−2D15
and/or
CL−600−2D24
15001 thru 15990. [1]
CL−600−2E25 19001 thru 19990. [1]
[1] There is no production effectivity.
(2) Spares Affected:
SPARES: Examine all NLG and MLG spare components and dothe procedures in this service bulletin.

### Page 4

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 2 of 29
Dec 14/2020
Revision A, Dec 02/2021
NOTE: The instructions in this service bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by MHIRJ service bulletins. Before you do this service
bulletin, examine all Supplemental Type Certificates (STCs) and
Supplemental Type Approvals (STAs) or equivalent action changes
to make sure you can complete this service bulletin.
B. Reason
(1) Condition
The Maintenance Requirements Manual (MRM) Part 1, specifies that the Nose
Landing Gear (NLG) and the Main Landing Gear (MLG) must be overhauled
each 20,000 flight cycles. The MRM does not specify a calendar cap to
perform the overhaul of these components.
(2) Evidence
None
(3) Objective/Benefit
This service bulletin gives the procedure to inspect all of the NLG and the
MLG component maintenance documents and, if necessary, to remove the
landing gear components for restoration (overhaul) and to install serviceable
part(s) before return into service. The removal of the affected component
must be done to comply with the phase−in schedule time line depending on
the landing gear age since Entry Into Service (EIS) or since last overhaul.
NOTE: Aircraft that follow the Low Utilization Maintenance Program (LUMP)
have a 120 month calendar cap. This service bulletin is recommended
to make sure that this calendar cap limit is maintained
NOTE: This service bulletin is recommended for all operators, including LUMP
operators.

### Page 5

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 3 of 29
Dec 14/2020
Revision A, Dec 02/2021
C. Description
This service bulletin is divided into ten parts: PART A, PART B, PART C, PART D,
PART E, PART F , PART G, PART H, PART I, and PART J.
PART A − Inspection of the NLG and the MLG Component Maintenance
Documents.
The component maintenance documents of the NLG and the MLG installed on the
aircraft and all the NLG and the MLG spare components are inspected to determine
the component calendar age.
Appendix A is added to facilitate component tracking as reference only.
PART B − Removal of the NLG Component(s) from the Aircraft
If the inspection of the NLG component maintenance documents (PART A)
identifies that the components that follow must be overhauled, then the affected
NLG component(s) is/are removed from the aircraft and tagged unserviceable.
−NLG Assembly
−NLG Drag Brace
−NLG Door Drive Link
−NLG Retract Actuator
−NLG Manual Release Actuator
−NLG Steering Actuator
PART C −Overhaul of the NLG Component(s)
If necessary, an overhaul (restoration) of the affected NLG component(s) is/are
done per the AMM and MRB tasks.
PART D − Installation of Serviceable NLG Component(s) on the Aircraft
If necessary, serviceable NLG component(s) are installed on the aircraft per the
AMM and MRB tasks.
PART E − Removal of the Left MLG Component(s) from the Aircraft
If the inspection of the left MLG component maintenance documents (PART A)
identifies that the components that follow must be overhauled, then the affected left
MLG component(s) is/are removed from the aircraft and tagged unserviceable.
−MLG Assembly
−MLG Side Stay
−MLG Shimmy Damper
−MLG Retract Actuator

### Page 6

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 4 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART F −Overhaul of the Left MLG Component(s)
If necessary, an overhaul (restoration) of the affected left MLG component(s) is/are
done per the AMM and MRB tasks.
PART G −Installation of Serviceable Left MLG Component(s) on the Aircraft
If necessary, serviceable left MLG component(s) are installed on the aircraft.
PART H − Removal of the Right MLG Component(s) from the Aircraft
If the inspection of the right MLG component maintenance documents (PART A)
identifies that the components that follow must be overhauled, then the affected
right MLG component(s) is/are removed from the aircraft and tagged
unserviceable.
−MLG Assembly
−MLG Side Stay
−MLG Shimmy Damper
−MLG Retract Actuator
PART I −Overhaul of the right MLG Component(s)
If necessary, an overhaul (restoration) of the affected right MLG component(s)
is/are done per the AMM and MRB tasks.
PART J − Installation of Serviceable Right MLG Component(s) on the Aircraft
If necessary, serviceable right MLG component(s) are installed on the aircraft.
D. Compliance
Recommended service bulletin.
PART A − Inspection of the NLG and the MLG Component Maintenance
Documents.
MHIRJ recommends that PART A of this service bulletin be done at no more than
three months from the release date of this service bulletin. Refer to the component
calendar age that follows to find out if some components on the NLG and the MLG
must be scheduled for an overhaul, unless otherwise directed by the airworthiness
authority of the operator.

### Page 7

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 5 of 29
Dec 14/2020
Revision A, Dec 02/2021
Component Calendar Age
If the component calendar age since EIS (without overhaul) or since last overhaul
is:
NOTE: The component’s calendar age is the calendar time since the aircraft
Certificate of Airworthiness (C of A) date (for components initially
installed on aircraft at time of delivery from the production line) or since
the component’s manufacturing date or since the component’s overhaul
date. 
The storage time of a new or an overhauled component can be
subtracted from the components age if the operator has correct
documentation and that the component was stored per the
manufacturer’s Component Maintenance Manual (CMM) and that the
component has not been installed on an aircraft before.
− Between 120 and 144 months (10 and 12 years):
Remove the component from service and tag it unserviceable before
it gets to 168 months (14 years) from EIS (without overhaul) or since
it was last overhauled and do the restoration (overhaul) on the
component at the operators discretion. (Refer to the COMPONENT
RESTORATION (OVERHAUL) TABLE for the AMM and MRB tasks).
− Between 144 and 168 months (12 and 14 years):
Remove the component from service and tag it unserviceable before
it gets to 24 months from the service bulletin PART A completion date
or before it gets to 186 months (15.5 years) from EIS (without
overhaul) or since it was last overhauled, whichever comes first and
do the restoration on the component at the operators discretion.
(Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for
the AMM and MRB tasks).
− Between 168 and 186 months (14 and 15.5 years):
Remove the component from service and tag it unserviceable before
it gets to 18 months from the service bulletin PART A completion date
or before it gets to 198 months (16.5 years) from EIS (without
overhaul) or since it was last overhauled, whichever comes first and
do the restoration on the component at the operators discretion.
(Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for
the AMM and MRB tasks).

### Page 8

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 6 of 29
Dec 14/2020
Revision A, Dec 02/2021
− Between 186 and 204 months (15.5 and 17 years):
Remove the component from service and tag it unserviceable before
it gets to 12 months from the service bulletin PART A completion date
or before it gets to 213 months (17.75 years) from EIS (without
overhaul) or since it was last overhauled, whichever comes first and
do the restoration on the component at the operators discretion.
(Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for
the AMM and MRB tasks).
− Between 204 and 216 months (17 and 18 years):
Remove the component from service and tag it unserviceable before
it gets to 9 months from the service bulletin PART A completion date
or before it gets to 222 months (18.5 years) from EIS (without
overhaul) or since it was last overhauled, whichever comes first and
do the restoration on the component at the operators discretion.
(Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for
the AMM and MRB tasks).
− Higher than 216 months (18 years):
Remove the component from service and tag it unserviceable before
it gets to 6 months from the service bulletin PART A completion date
and do the restoration (overhaul) on the component at the operators
discretion. (Refer to the COMPONENT RESTORATION (OVERHAUL)
TABLE for the AMM and MRB tasks).
PART B − Removal of the NLG Component(s) from the Aircraft
PART B is done if the inspection of the component maintenance documents (PART
A) identifies that some NLG component(s) must be overhauled.
If an overhaul of the NLG component(s) is/are required, the affected NLG gear
component(s) is removed from service unless otherwise directed by the
airworthiness authority of the operator:
PART C −Overhaul of the NLG Component(s)
PART C is done if the inspection of the component maintenance documents (PART
A) identifies that some NLG component(s) must be overhauled.
PART D − Installation of Serviceable NLG Component(s) on the Aircraft
PART D is done to install serviceable NLG components on the aircraft.

### Page 9

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 7 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART E − Removal of the Left MLG Component(s) from the Aircraft
PART E is done if the inspection of the component maintenance documents (PART
A) identifies that some left MLG component(s) must be overhauled.
If an overhaul of the left MLG component(s) is/are required, the affected left MLG
gear component(s) is removed from service unless otherwise directed by the
airworthiness authority of the operator:
PART F −Overhaul of the Left MLG Component(s)
PART F is done if the inspection of the component maintenance documents (PART
A) identifies that some left MLG component(s) must be overhauled.
PART G − Installation of Serviceable Left MLG Component(s) on the Aircraft
PART G is done to install serviceable left MLG components on the aircraft.
PART H − Removal of the Right MLG Component(s) from the Aircraft
PART H is done if the inspection of the component maintenance documents (PART
A) identifies that some right MLG component(s) must be overhauled.
If an overhaul of the right MLG component(s) is/are required, the affected right
MLG gear component(s) is removed from service unless otherwise directed by the
airworthiness authority of the operator:
PART I −Overhaul of the Right MLG Component(s)
PART I is done if the inspection of the component maintenance documents (PART
A) identifies that some right MLG component(s) must be overhauled.
PART J − Installation of Serviceable Right MLG Component(s) on the Aircraft
PART J is done to install serviceable right MLG components on the aircraft.

### Page 10

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 8 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART A, PART B, PART C,PART D, PART E, PART F , PART G, PART H, PART I
and PART J
NOTE: If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative
of MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or
e-mail at thd.crj@MHIRJ.com for analysis and to get an approved
disposition to complete this service bulletin.
This service bulletin does not affect Airworthiness Limitations (AWLs) or Damage
Tolerance Inspections (DTIs).
E. Approval
The technical content of this service bulletin has been approved under the authority
of the TCCA Design Approval Organization No: DAO #20−Q−01.
F . Manpower
The man-hours given below are estimates for direct labor done by an experienced
crew on an aircraft prepared for maintenance.
These estimates do not include the time necessary for:
−Administrative functions such as planning, liaising, familiarization, and report writing.
−Non-productive elapsed time such as rest time, having meals, and crew shift
changes.
−Elapsed time such as for paint to dry, sealant to cure, and fuel tank venting.
−Preparation for modification (unless specified in the Accomplishment
Instructions) such as cleaning and getting parts, tools, consumables, and
ground equipment.
−Quality assurance inspections, troubleshooting and/or correction of
discrepancies found when a task is done.
−All other activities that are not considered by MHIRJ as directly related to the
accomplishment of this procedure.
NOTE: For on-site labor assistance, please speak with a Fleet Services
representative for an estimate. Call the Fleet Services Team through the
CRC at  450−990−7CRC (450−990−7272) direct, 1−833−990−7CRC
(1−833−990−7272) toll free for North America or +1−450−990−7CRC
(+1−450−990−7272) for international callers or e-mail at
thd.crj@MHIRJ.com.

### Page 11

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 9 of 29
Dec 14/2020
Revision A, Dec 02/2021
It will take an estimated 4.5 man-hours to complete PART A of this service bulletin.
The man-hours are divided in the table that follows:
TASK MAN-HOURS
(1)  Job Set-Up 0.0
(2)  Procedure 4.0
(3)  Test 0.0
(4)  Job Close-Out 0.5
NOTE: The hours above are to do the inspection (PART A) of the
documentation only and do not include the time to remove and/or
overhaul and/or re−install the component(s) (PART B thru PART
J).
G. Material − Price and Availability
There are no kits for this service bulletin.
H. Tooling − Price and Availability
There are no tool kits for this service bulletin. Refer to paragraph 3.C. for a list of
special tools and equipment for this service bulletin.
I. Weight and Balance
Not changed.
J. Electrical Load Data
Not changed.
K. References
Refer to the SB Introduction document for definition or explanation of service
bulletin content.
For MHIRJ reference only: Restriction and/or Special Instruction (RSI) C−32−1913,
Revision C.
For MHIRJ reference only: PCR 77480
L. Other Publications Affected
None.
M. Relationship Chart
Not applicable.

### Page 12

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 10 of 29
Dec 14/2020
Revision A, Dec 02/2021
2. ACCOMPLISHMENT INSTRUCTIONS
PART A − Inspection of the NLG and the MLG Component Maintenance Documents.
A. Job Set-Up
(1) There is no Job set−up for the administrative inspection of the NLG and MLG
component maintenance documents.  If it is found necessary to do an
overhaul on a NLG and/or a MLG component, then refer to the AMM and MRB
tasks as noted in the Procedure section of PART B, PART C, PART D, PART E,
PART F , PART G, PART H, PART I and/or PART J.
B. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers  or
e-mail at thd.crj@MHIRJ.com for analysis and to get an approved disposition
to complete this service bulletin.
(2) Do an inspection of the NLG and the MLG component maintenance
documents of the components that follow to determine the component’s
calendar age.
−NLG Assembly
−NLG Drag Brace
−NLG Door Drive Link
−NLG Retract Actuator
−NLG Manual Release Actuator
−NLG Steering Actuator
−MLG Assembly
−MLG Side Stay
−MLG Shimmy Damper
−MLG Retract Actuator

### Page 13

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 11 of 29
Dec 14/2020
Revision A, Dec 02/2021
NOTE: The component calendar age is the calendar time since the aircraft
Certificate of Airworthiness (C of A) date (for components initially
installed on aircraft at time of delivery from the production line) or since
the component’s manufacturing date or since the component’s
overhaul date. 
The storage time of a new or an overhauled component can be
subtracted from the components age if the operator has correct
documentation and that the component was stored per the
manufacturer’s Component Maintenance Manual (CMM) and that the
component has not been installed on an aircraft before.
(3) Go to the Close−Out section of this service bulletin to record the completion
of PART A .
C. Job Close-Out
(1) When PART A of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation, PART A, incorporated."
PART B − Removal of the NLG Component(s) from the Aircraft
NOTE: PART B is to be done if the inspection of the NLG component
maintenance documents (PART A) identifies that some NLG
components must be removed from the aircraft.
Reference Information
REFERENCE DESIGNATION
AMM 12−00−00−867−801 Standard Aircraft Configuration for Maintenance
AMM 24−00−00−861−802 Remove Electrical Power from the Aircraft
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 32−21−01−000−801 Removal of the NLG Shock−Strut assembly
AMM 32−21−05−000−801 Removal of the NLG Drag Brace
AMM 32−22−07−000−802 Removal of the NLG Drive Link
AMM 32−32−09−000−801 Removal of the NLG Retract−Actuator

### Page 14

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 12 of 29
Dec 14/2020
Revision A, Dec 02/2021
REFERENCE DESIGNATION
AMM 32−34−16−000−801 Removal of the NLG
Alternate−Release−Actuator
AMM 32−52−01−000−801 Removal of the Steering Actuator/LVDT
D. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Make sure that the aircraft is in standard configuration for maintenance
(refer to AMM 12−00−00−867−801).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).
(3) Remove electrical power from the aircraft (refer to AMM
24−00−00−861−802).
E. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
(2) If necessary, remove the NLG shock−strut assembly (refer to AMM
32−21−01−000−801).

### Page 15

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 13 of 29
Dec 14/2020
Revision A, Dec 02/2021
(3) If necessary, remove the NLG drag brace (refer to AMM
32−21−05−000−801).
(4) If necessary, remove the NLG door drive link (refer to AMM
32−22−07−000−802).
(5) If necessary, remove the NLG retract−actuator (refer to AMM
32−32−09−000−801).
(6) If necessary, remove the NLG alternate−release−actuator (refer to AMM
32−34−16−000−801).
(7) If necessary, remove the NLG steering actuator (refer to AMM
32−52−01−000−801).
F . Job Close-Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) When PART B of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation, PART B, incorporated."
NOTE: PART B can only be recorded as /quoteblleftincorporated" once all identified
components to be overhauled have been removed from the aircraft.

### Page 16

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 14 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART C −Overhaul of the NLG Component(s)
NOTE: PART C is done if the inspection of the component maintenance
documents (PART A) identifies that some NLG component(s) must be
overhauled.
Reference Information
REFERENCE DESIGNATION
AMM 32−21−00−610−801 Restoration (Overhaul) of the
Nose Landing−Gear Assembly
AMM 32−21−05−610−801 Restoration (Overhaul) of the
Nose Landing−Gear Drag Brace
AMM 32−22−07−610−801 Restoration (Overhaul) of the
NLG Door Drive Link
AMM 32−32−09−610−801 Restoration (Overhaul) of the
Nose Landing−Gear Retract Actuator
AMM 32−34−16−610−801 Restoration (Overhaul) of the
Nose Landing−Gear Manual Release Actuator
AMM 32−52−01−610−801 Restoration (Overhaul) of the
Nose Landing−Gear Steering Actuator
G. Job Set-Up
NOTE: There are no specific Job Set−Up tasks for the restoration (overhaul) on
the component(s) for this service bulletin as all component(s) have been
removed from the aircraft in PART B.
H. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.

### Page 17

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 15 of 29
Dec 14/2020
Revision A, Dec 02/2021
(2) Do the restoration (overhaul) on the NLG component(s) that was identified in
PART A and removed from the aircraft in PART B as follows:
NOTE: Restoration (overhaul) on the component(s) as documented from PART
A is at the operators discretion.
(a) Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for the
AMM and MRB tasks to be used for the overhaul procedures of the NLG
component(s).
COMPONENT RESTORATION (OVERHAUL) TABLE
COMPONENT AMM TASK MRB TASK
NLG Assembly 32−21−00−610−801 320100−211
NLG Drag Brace 32−21−05−610−801 320100−226
NLG Door Drive Link 32−22−07−610−801 320100−232
NLG Retract Actuator 32−32−09−610−801 320100−223
NLG Manual Release Actuator 32−34−16−610−801 320100−225
NLG Steering Actuator 32−52−01−610−801 320100−224
I. Job Close-Out
(1) When PART C of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART C, incorporated."

### Page 18

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 16 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART D − Installation of Serviceable NLG Component(s) on the Aircraft
NOTE: PART D is done to install serviceable NLG components on the aircraft.
Reference Information
AMM 32−22−07−400−802 Installation of the NLG Drive Link
AMM 32−21−01−400−801 Installation of the NLG Shock−Strut assembly
AMM 32−21−05−400−801 Installation of the NLG Drag Brace
AMM 32−32−09−400−801 Installation of the NLG Retract−Actuator
AMM 32−34−16−000−801 Installation of the NLG
Alternate−Release−Actuator
AMM 32−52−01−400−801 Installation of the Steering Actuator/LVDT
J. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(1) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).
K. Procedure
(1) If removed, install a serviceable NLG shock−strut assembly (refer to AMM
32−21−01−400−801).
(2) If removed, install a serviceable NLG drag brace (refer to AMM
32−21−05−400−801).
(3) If removed, install a serviceable NLG door drive link (refer to AMM
32−22−07−400−802).

### Page 19

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 17 of 29
Dec 14/2020
Revision A, Dec 02/2021
(4) If removed, install a serviceable NLG retract−actuator (refer to AMM
32−32−09−400−801).
(5) If removed, install a serviceable NLG alternate−release−actuator (refer to
AMM 32−34−16−400−801).
(6) If removed, install a serviceable NLG steering actuator (refer to AMM
32−52−01−400−801).
L. Job Close-Out
(1) If necessary, remove all tools, equipment, and unwanted materials from the
work area.
(2) When PART D of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART D, incorporated."
NOTE: PART D can only be recorded as /quoteblleftincorporated" once all identified
components from PART A have been replaced with serviceable
components on the aircraft.

### Page 20

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 18 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART E − Removal of the Left MLG Component(s) from the Aircraft
NOTE: PART E is only required to be done if the inspection of the landing
component documents (PART A) identifies that some components must
be overhauled.
Reference Information
REFERENCE DESIGNATION
AMM 12−00−00−867−801 Standard Aircraft Configuration for Maintenance
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 24−00−00−861−802 Remove Electrical Power from the Aircraft
AMM 32−11−05−000−801 Removal of the MLG Shock−Strut Assembly
AMM 32−11−12−000−801 Removal of the MLG Side Stay Assembly
AMM 32−11−42−000−801 Removal of the MLG Shimmy Damper
AMM 32−32−05−000−801 Removal of the MLG Retraction−Actuator
M. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Make sure that the aircraft is in standard configuration for maintenance
(refer to AMM 12−00−00−867−801).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).
(3) Remove electrical power from the aircraft (refer to AMM
24−00−00−861−802).

### Page 21

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 19 of 29
Dec 14/2020
Revision A, Dec 02/2021
N. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(2) If necessary, remove the left MLG shock−strut assembly (refer to AMM
32−11−05−000−801).
(3) If necessary, remove the left MLG side stay assembly (refer to AMM
32−11−12−000−801).
(4) If necessary, remove the left MLG shimmy damper (refer to AMM
32−11−42−000−801).
(5) If necessary, remove the left MLG retraction actuator (refer to AMM
32−32−05−000−801).
O. Job Close-Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) When PART E of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation, PART E, incorporated."
NOTE: PART E can only be recorded as /quoteblleftincorporated" once all identified
components to be overhauled have been removed from the aircraft.

### Page 22

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 20 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART F −Overhaul of the Left MLG Component(s)
NOTE: PART F is done if the inspection of the component maintenance
documents (PART A) identifies that some NLG component(s) must be
overhauled.
Reference Information
COMPONENT RESTORATION (OVERHAUL) TABLE
COMPONENT AMM TASK MRB TASK
MLG Assembly 32−11−00−610−801 320100−210
MLG Side Stay 32−11−12−610−801 320100−227
MLG Shimmy Damper 32−11−42−610−801 320100−229
MLG Retract Actuator 32−32−05−610−801 320100−222
P . Job Set-Up
NOTE: There are no specific Job Set−Up tasks for the restoration (overhaul) on
the component(s) for this service bulletin as all component(s) have been
removed from the aircraft in PART E.
Q. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
(2) Do the restoration (overhaul) on the left MLG component(s) that was identified
in PART A and removed from the aircraft  in PART E as follows:
NOTE: Restoration (overhaul) on the component(s) as documented from PART
A is at the operators discretion.

### Page 23

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 21 of 29
Dec 14/2020
Revision A, Dec 02/2021
(a) Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for the
AMM and MRB tasks to be used for the overhaul procedures of the NLG
component(s).
AMM 32−11−00−610−801 Restoration (Overhaul) of the
Main Landing−Gear Assembly
AMM 32−11−12−610−801 Restoration (Overhaul) of the
Main Landing Gear Side Stay
AMM 32−11−42−610−801 Restoration (Belleville Washers Replacement) of
the MLG Shimmy Damper
AMM 32−32−05−610−801 Restoration (Overhaul) of the
Main Landing Gear Retraction−Actuator
R. Job Close-Out
(1) When PART F of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART F , incorporated."
PART G − Installation of Serviceable Left MLG Component(s) on the Aircraft
NOTE: PART G is done to install serviceable left MLG components on the
aircraft.
Reference Information
REFERENCE DESIGNATION
AMM 12−00−00−867−801 Standard Aircraft Configuration for Maintenance
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 32−11−05−400−801 Installation of the MLG Shock−Strut Assembly
AMM 32−11−12−400−801 Installation of the MLG Side Stay Assembly
AMM 32−11−42−400−801 Installation of the MLG Shimmy Damper
AMM 32−32−05−400−801 Installation of the MLG Retraction−Actuator

### Page 24

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 22 of 29
Dec 14/2020
Revision A, Dec 02/2021
S. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(1) Make sure that the aircraft is in standard configuration for maintenance
(refer to AMM 12−00−00−867−801).
(2) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).
T. Procedure
(1) If removed, Install a serviceable left MLG shock−strut assembly (refer to AMM
32−11−05−400−801).
(2) If removed, install a serviceable left MLG side stay assembly (refer to AMM
32−11−12−400−801).
(3) If removed, Install a serviceable left MLG shimmy damper (refer to AMM
32−11−42−400−801).
(4) If removed, install a serviceable left MLG retraction actuator (refer to AMM
32−32−05−400−801).

### Page 25

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 23 of 29
Dec 14/2020
Revision A, Dec 02/2021
U. Job Close-Out
(1) If necessary, remove all tools, equipment, and unwanted materials from the
work area.
(2) When PART G of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART G, incorporated."
NOTE: PART G can only be recorded as /quoteblleftincorporated" once all identified
components from PART A have been replaced with serviceable
components on the aircraft.
PART H − Removal of the Right MLG Component(s) from the Aircraft
NOTE: PART H is only required to be done if the inspection of the landing
component documents (PART A) identifies that some components must
be overhauled.
Reference Information
REFERENCE DESIGNATION
AMM 12−00−00−867−801 Standard Aircraft Configuration for Maintenance
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 24−00−00−861−802 Remove Electrical Power from the Aircraft
AMM 32−11−05−000−801 Removal of the MLG Shock−Strut Assembly
AMM 32−11−12−000−801 Removal of the MLG Side Stay Assembly
AMM 32−11−42−000−801 Removal of the MLG Shimmy Damper
AMM 32−32−05−000−801 Removal of the MLG Retraction−Actuator

### Page 26

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 24 of 29
Dec 14/2020
Revision A, Dec 02/2021
V. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(1) Make sure that the aircraft is in standard configuration for maintenance
(refer to AMM 12−00−00−867−801).
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(2) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).
(3) Remove electrical power from the aircraft (refer to AMM
24−00−00−861−802).
W. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
(2) If necessary, remove the right MLG shock−strut assembly (refer to AMM
32−11−05−000−801).
(3) If necessary, remove the right MLG side stay assembly (refer to AMM
32−11−12−000−801).

### Page 27

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 25 of 29
Dec 14/2020
Revision A, Dec 02/2021
(4) If necessary, remove the right MLG shimmy damper (refer to AMM
32−11−42−000−801).
(5) If necessary, remove the right MLG retraction actuator (refer to AMM
32−32−05−000−801).
X. Job Close-Out
(1) Remove all tools, equipment, and unwanted materials from the work area.
(2) When PART H of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation, PART H, incorporated."
NOTE: PART H can only be recorded as /quoteblleftincorporated" once all identified
components to be overhauled have been removed from the aircraft.
PART I −Overhaul of the Right MLG Component(s)
NOTE: PART I is done if the inspection of the component maintenance
documents (PART A) identifies that some right MLG component(s) must
be overhauled.
Reference Information
COMPONENT RESTORATION (OVERHAUL) TABLE
COMPONENT AMM TASK MRB TASK
MLG Assembly 32−11−00−610−801 320100−210
MLG Side Stay 32−11−12−610−801 320100−227
MLG Shimmy Damper 32−11−42−610−801 320100−229
MLG Retract Actuator 32−32−05−610−801 320100−222
Y . Job Set-Up
NOTE: There are no specific Job Set−Up tasks for the restoration (overhaul) on
the component(s) for this service bulletin as all component(s) have been
removed from the aircraft in PART H.

### Page 28

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 26 of 29
Dec 14/2020
Revision A, Dec 02/2021
Z. Procedure
(1) If it is not possible to complete all the instructions in this service bulletin
because of the configuration of the aircraft, speak with a representative of
MHIRJ in the CRC at 450−990−7CRC (450−990−7272) direct,
1−833−990−7CRC (1−833−990−7272) toll free for North America or
+1−450−990−7CRC (+1−450−990−7272) for international callers or e-mail
at thd.crj@MHIRJ.com for analysis and to get an approved disposition to
complete this service bulletin.
(2) Do the restoration (overhaul) on the right MLG component(s) that was
identified in PART A and removed from the aircraft in PART H as follows:
NOTE: Restoration (overhaul) on the component(s) as documented from PART
A is at the operators discretion.
(a) Refer to the COMPONENT RESTORATION (OVERHAUL) TABLE for the
AMM and MRB tasks to be used for the overhaul procedures of the NLG
component(s).
AMM 32−11−00−610−801 Restoration (Overhaul) of the
Main Landing−Gear Assembly
AMM 32−11−12−610−801 Restoration (Overhaul) of the
Main Landing Gear Side Stay
AMM 32−11−42−610−801 Restoration (Belleville Washers Replacement) of
the MLG Shimmy Damper
AMM 32−32−05−610−801 Restoration (Overhaul) of the
Main Landing Gear Retraction−Actuator
AA. Job Close-Out
(1) When PART I of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART I, incorporated."

### Page 29

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 27 of 29
Dec 14/2020
Revision A, Dec 02/2021
PART J − Installation of Serviceable Right MLG Component(s) on the Aircraft
NOTE: PART J is done to install serviceable right MLG components on the
aircraft.
Reference Information
REFERENCE DESIGNATION
AMM 12−00−00−867−801 Standard Aircraft Configuration for Maintenance
AMM 24−00−00−910−801 Electrical/Electronic Safety Precautions
AMM 32−11−05−400−801 Installation of the MLG Shock−Strut Assembly
AMM 32−11−12−400−801 Installation of the MLG Side Stay Assembly
AMM 32−11−42−400−801 Installation of the MLG Shimmy Damper
AMM 32−32−05−400−801 Installation of the MLG Retraction−Actuator
AB. Job Set-Up
NOTE: The steps in the Job Set-Up section of this service bulletin are
recommended steps. The steps give a recommendation to get access
to the work area. This recommendation is to give a safe work area and
to minimize possible damage to surrounding aircraft parts. Alternative
steps can be used at the operator discretion.
WARNING: OBEY ALL THE SAFETY PRECAUTIONS WHEN YOU DO
MAINTENANCE ON OR NEAR ELECTRICAL/ELECTRONIC
EQUIPMENT. IF YOU DO NOT OBEY THE SAFETY PRECAUTIONS,
INJURIES TO PERSONS AND/OR DAMAGE TO THE EQUIPMENT CAN
OCCUR.
(1) Make sure that the aircraft is in standard configuration for maintenance
(refer to AMM 12−00−00−867−801).
(2) Obey all the electrical/electronic safety precautions (refer to AMM
24−00−00−910−801).

### Page 30

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 28 of 29
Dec 14/2020
Revision A, Dec 02/2021
AC. Procedure
(1) If removed, Install a serviceable right MLG shock−strut assembly (refer to
AMM 32−11−05−400−801).
(2) If removed, install a serviceable right MLG side stay assembly (refer to AMM
32−11−12−400−801).
(3) If removed, Install a serviceable right MLG shimmy damper (refer to AMM
32−11−42−400−801).
(4) If removed, install a serviceable right MLG retraction actuator (refer to AMM
32−32−05−400−801).
AD. Job Close-Out
(1) If necessary, remove all tools, equipment, and unwanted materials from the
work area.
(2) When PART J of this service bulletin is completed, make this entry in the
applicable logbooks: /quoteblleft Service Bulletin 670BA−32−062, Revision A, Landing
Gear − Landing Gear System, General − Inspection of Landing Gear
Component(s) Maintenance Documentation and, if required, removal of
affected component(s) from service for overhaul, PART J, incorporated."
NOTE: PART J can only be recorded as /quoteblleftincorporated" once all identified
components from PART A have been replaced with serviceable
components on the aircraft.

### Page 31

SERVICE BULLETIN  670BA−32−062
SB 670BA−32−062
Page 29 of 29
Dec 14/2020
Revision A, Dec 02/2021
3. MATERIAL INFORMATION
A. Kit Information
None.
B. Consumable Information
For a list of consumables, refer to the different tasks that are given as references in
this service bulletin.
C. Special Tools and Equipment
For a list of special tools and equipment, refer to the different tasks that are given
as references in this service bulletin.
D. Disposition of Parts
Not applicable.
1

### Page 32

APPENDIX A
Page A1 of A2
Dec 02/2021
APPENDIX A
SERVICE BULLETIN 670BA−32−062
Inspection of Landing Gear Component(s) Maintenance Documentation and, if
Required, Removal of Affected Component(s) from Service for Overhaul
The procedure contained in this appendix is given as reference in the
Accomplishment Instructions of Service Bulletin 670BA−32−062.

### Page 33

APPENDIX A
SERVICE BULLETIN 670BA−32−062
APPENDIX A
Page A2 of A2
Dec 02/2021
In the table below, list all NLG and MLG components that must be removed from
the aircraft as a result of the findings in PART A of the service bulletin based on
Time Since New (TSN) or Time Since Overhaul (TSO).
NLG and MLG COMPONENT REMOVAL SCHEDULE
AIRCRAFT SERIAL NO.                                           
DATE TABLE COMPLETED                                        
COMPONENT(S) COMPONENT
PART
NUMBER
COMPONENT
SERIAL
NUMBER
COMPONENT
REMOVAL
DUE DATE
INSTALLED
COMPONENT
TSN/TSO
APPLICABLE NLG COMPONENT(S)
NLG Assembly
NLG Drag Brace
NLG Door Drive Link
NLG Retract Actuator
NLG Manual Release
Actuator
NLG Steering Actuator
APPLICABLE LEFT MLG COMPONENT(S)
MLG Assembly
MLG Side Stay
MLG Shimmy Damper
MLG Retract Actuator
APPLICABLE RIGHT MLG COMPONENT(S)
MLG Assembly
MLG Side Stay
MLG Shimmy Damper
MLG Retract Actuator

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
