# Bombardier Alert Service Bulletin A601-0627: Revision 02

- Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-0082; AD 2015-02-23 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bombardier Alert Service Bulletin A601-0627](https://openairdocs.org/service-documents/bombardier/a601-0627.md)
- Title as filed: U.S. DOT/FAA - A601-0627 Revision02
- Pages: 24
- PDF: https://openairdocs.org/files/sha256/bc/bc/bcbc5d845c33378b8b0226a53bcadf152cdfb2dee3d3353dc324d08bbcfb8d8c
- Page: https://openairdocs.org/service-documents/bombardier/a601-0627/file/bcbc5d845c33

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

A601-0627Page 1 of 1
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
MODEL CL-600-2A12 & CL-600-2B16
Discard the Revision 01 of this Service Bulletin dated Feb 26/2013, and replace in its
entirety with this Revision 02.
Service Bulletin No. A601-0627
Date of Basic Issue Sep 26/2013
Revision No. 01 Dated Feb 26/2014
Revision No. 02 Dated Dec 09/2014
For action applicable to aircraft on which the Basic Issue or Revision 01 of this
Service Bulletin was done, refer to the retroactive action box on Page 1 of this
Service Bulletin.
This revision has no effect for aircraft on which PART B or PART C of this
Service Bulletin was done thus no other action is necessary.  Do not sign the
log book if you have not done this revision.  Keep the previous log book entry.
You may make an entry as “Not Applicable” for this revision.
This revision is issued to:
1. Change the Service Bulletin Summary Sheet and Paragraph 1.D., Compliance Time,
to reflect the Restriction and/or Special Instruction (RSI), C-4095, Rev. D.
2. Add in the Service Bulletin Summary Sheet, in the Planning Information note and in
Paragraph 1.D., Compliance, a note for the Airworthiness Directive
3. Add a retroactive action box.
4. Change, in Paragraph 1.K., the revision of the Restriction and/or Special Instruction
(RSI), C-4095, to Rev. D.
5. Make miscellaneous minor changes, as necessary, with no change of context.

### Page 2

Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 1 of 1
ALERT SERVICE BULLETIN SUMMARYThis Service Bulletin is available at:
www.cic.bombardier.com
MODEL CL-600-2A12 & CL-600-2B16
ATA 57-40
WINGS
SPECIAL CHECK/MODIFICATION – ATTACHMENT FITTINGS –
INBOARD FLAP HINGE BOX FORWARD ATTACHMENT FITTINGS FASTENERS
The information below is provided for your reference.  For full details, please
see corresponding paragraph contained within this bulletin.
ALERTSPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
PART A is recommended within 100 landings
from this Alert Service Bulletin release date
(Basic Issue) or within 50 landings from this
Alert Service Bulletin release date (Revision 02)
and must be repeated every 10 landings until
modification in PART B is complied with or
PART C is completed.
PART B is recommended no later than
24 months from this Alert Service Bulletin
release date (Revision 02).
EFFECTIVITY: A/C Serial No. 3001 to 3066
A/C Serial No. 5001 to 5194
MANPOWER: 1 man-hour for the special check in PART A
58 man-hours for the modification in PART B
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
TLMC, CH 5 AFFECTED YES NO
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION:  See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTES 1. Defueling and venting of the fuel tanks must be done to do PART B of this
Service Bulletin.
2. To minimize aircraft downtime and cost, it is recommended to do     Service Bulletin
601-0631, in conjunction with PART B of     this Service Bulletin.
3. This Service Bulletin is mandated by Airworthiness Directive (AD) CF-2013-39R1.
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:
514-855-2999 or 1-866-538-1247

### Page 3

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry
standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
© 2013 - 2014 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 1 of 19
ALERT SERVICE
BULLETINThis Alert Service Bulletin is available at:
www.cic.bombardier.com
MODEL CL-600-2A12 & CL-600-2B16
ATA 57-40
WINGS
SPECIAL CHECK/MODIFICATION – ATTACHMENT FITTINGS –
INBOARD FLAP HINGE BOX FORWARD ATTACHMENT FITTINGS FASTENERS
RETROACTIVE ACTION
1. RETROACTIVE ACTION APPLICABLE TO AIRCRAFT THAT HAVE
INCORPORATED THE BASIC ISSUE  OR REVISION 01 OF PART A OF THIS
SERVICE BULLETIN:
A. FOR THE AIRCRAFT WITH THE INCORRECTLY ORIENTED FORWARD
FASTENERS HEADS (FIGURE 2 in PART A), PART A MUST BE DONE
WITHIN 10 LANDINGS FROM THIS ALERT SERVICE BULLETIN RELEASE
DATE (REVISION 02) AND MUST BE REPEATED EVERY 10 LANDINGS
UNTIL PART B IS COMPLIED WITH.
– NO FURTHER ACTION IS REQUIRED, ONCE PART B IS
INCORPORATED.
OR
B. FOR THE AIRCRAFT WITH THE CORRECTLY ORIENTED FORWARD
FASTENERS HEADS (FIGURE 1 in PART A).
– NO FURTHER ACTION IS REQUIRED, ONCE PART C IS COMPLETED.
2. NO RETROACTIVE ACTION IS REQUIRED FOR AIRCRAFT THAT HAVE
INCORPORATED PART B OR PART C OF THE BASIC ISSUE OR REVISION 01
OF THIS SERVICE BULLETIN.

### Page 4

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 2 of 19
2. PLANNING INFORMATION
NOTES: 1. To minimize aircraft downtime and cost, it is recommended to do
 Service Bulletin 601-0631, in conjunction with PART B of     this Service
Bulletin.
2. This Service Bulletin is mandated by Airworthiness Directive (AD)
CF-2013-39R1.
A. Effectivity
CL-600-2A12 aircraft, Serial No. 3001 to 3066.
CL-600-2B16 aircraft, Serial No. 5001 to 5194.
NOTE: The instructions given in this Alert Service Bulletin are only applicable
to the systems and parts installed at the time of delivery of the aircraft
or as changed by Bombardier Aerospace Alert Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent
action changes to make sure that this bulletin can be completed.
B. Reason
On a Challenger 605 zonal inspection, one of the two forward fasteners
attaching the inboard flap hinge box forward hinge fitting at Wing Station (WS)
76.50 was found with its head missing.
The investigation shows that when installed with their head outside, those
fasteners will experience premature failure caused by higher pre-load due to
clamping and alignment.
This Alert Service Bulletin provides instructions to inspect and repair the
forward fasteners attaching the forward fittings at WS 76.50 and WS 127.25
at both wings.
C. Description
This Alert Service Bulletin gives instructions in:
PART A, to:
– Do the inspection of the forward inboard flap fasteners on the hinge box wing
forward fitting.
PART B, to:
– Remove the forward and aft inboard flap hinge-fairings,
– Remove the applicable upper and lower access panels,
– Do the inboard flap fasteners modifications as per APPENDIX 1 on the hinge
box wing forward fittings,
– Install the removed wing upper and lower access panels, and
– Re-install the forward and aft inboard flap hinge-fairings.

### Page 5

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 3 of 19
In PART C, to:
– Confirm that the forward fasteners heads are correctly oriented.
In Testing, to:
– Do the necessary testing to ensure that the inboard flaps operate correctly.
D. Compliance
PART A is recommended within 100 landings from this Alert Service Bulletin
release date (Basic Issue) or within 50 landings from this Alert Service Bulletin
release date (Revision 02) and must be repeated every 10 landings until
modification in PART B is complied with or until PART C is completed to confirm
that the forward fasteners heads are correctly oriented.
PART B is recommended no later than 24 months from this Alert Service
Bulletin release date (Revision 02).
NOTES:  1. At any time, if any of the forward fasteners heads are found
missing, PART B must be implemented before further flight.
2. If the modification in PART B is incorporated or if the forward
fasteners heads are correctly oriented as per PART C, no further
action is required.
3. This Service Bulletin is mandated by Airworthiness Directive (AD)
CF-2013-39R1.
E. Approval
The technical content of this Service Bulletin has been approved under
the authority of Transport Canada Civil Aviation (TCCA) Design Approval
Organization (DAO) No. DAO #93-Q-02.
NOTES: 1. The technical content of this Alert Service Bulletin is accepted by the
FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
in accordance with established procedures.

### Page 6

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 4 of 19
F. Manpower
NOTES: 1. The man-hours given are estimates to help you schedule the tasks
given in this bulletin.  The estimates are for direct labor performed
by an experienced crew and do not include the time for
familiarization, planning, aircraft preparation in hangar such as
towing and positioning of scaffolds, removal of interior furnishings,
repainting, supervision and inspection.
For more information related to the manpower estimates, refer to
SB 601-0002.
2. This Alert Service Bulletin may require consumable materials
that have specific curing times (refer to Paragraph 3).  The
accumulated curing time is not included in the labor estimates
and should be considered for planning purposes before you
schedule this Alert Service Bulletin.
1 man-hour is necessary to do the special check in PART A.
58 man-hours are necessary to do this modification in PART B.
Bombardier does not pay for the special check in PART A and the Fuel
Disposal fee at any time.
The labor required to do the modification in PART B is at no cost if:
(i) the work is done at Bombardier Business Aviation Services (BBAS)
or Authorized Service Facilities (ASF), and
(ii) this Service Bulletin is scheduled in less than 48 months from
its release date (Basic Issue).
G. Material - Cost and Availability
No kits or parts are necessary to do the special check in PART A or to confirm that
the forward fasteners heads are correctly oriented as per PART C.
When applicable, submit an SRPSA to Customer Support Engineering (CSE) to
obtain the kit and part details necessary to do PART B of this modification.
If applicable, the kit for PART B is available at no cost if a no-charge purchase
order is sent to Bombardier Aerospace in less than 48 months from this Service
Bulletin release date (Basic Issue).
Bombardier does not pay for the bushings that may be necessary, to do PART B,
of this Service Bulletin.
Bombardier does not pay for the Fuel Disposal fee at any time.
During or after the above free period, Smart Parts Plus does not pay for the kit.

### Page 7

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 5 of 19
H. Tooling
The tools that follow, or equivalent, are necessary to do PART A of this Alert
Service Bulletin:
GSE REFERENCE NO. PART NO. DESCRIPTION
24-00-24 S4933959−501 Tag, Circuit Breaker
Commercially Available - Borescope
The tools that follow, or equivalent, are necessary to do PART B of this Alert
Service Bulletin:
GSE REFERENCE NO. PART NO. DESCRIPTION
24-00-24 S4933959−501 Tag, Circuit Breaker
28-00-06 8320000 Fuel Fumes Detector
Commercially Available - Torque Wrench 20 to 25 lbfin (2.26 to 2.82 Nm)
Commercially Available - Torque Wrench 30 to 35 lbfin (3.39 to 3.95 Nm)
The tools listed below or commercially available equivalent tools are required
for the removal of the bushings.
REFERENCE NO. PART NO. DESCRIPTION
Commercially Available - C-Clamp
See Note 3 - Support Block
NOTES: 1. Refer to the Illustrated Tool and Equipment Manual (ITEM), PSP611
to make sure that you use the correct equipment configuration.
2. Refer to the Introduction of the publication listed in NOTE 1 for
acceptable GSE equivalents.
3. For the support block manufacturing details, refer to Appendix 2.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.

### Page 8

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 6 of 19
K. References
– Bombardier Aerospace, Restriction and/or Special Instruction (RSI),
C-4095, Rev. D.
– CL-601 Maintenance Manual, PSP 601-2, Chapters 6, 12, 24, 28, and 57.
– CL-601 Illustrated Parts Catalog (IPC), PSP 601-4, Chapter 57.
– CL-601 Structural Repair Manual (SRM), PSP 607, Chapter 51.
– CL-601 Illustrated Tool and Equipment Manual (ITEM), PSP 611,
Chapters 24 and 28.
– Bombardier Aerospace, Modification Summary IS600-57-0001, Rev. A.
– Bombardier Aerospace, Repair Engineering Order (REO), 600-57-26-001.
– Bombardier Aerospace, Kit Drawing K600-10110, Rev. --.
– Bombardier Aerospace, Appendix 1 (attached).
– Bombardier Aerospace, Appendix 2 (attached).
L. Other Publications Affected
None
M. Equivalent Service Bulletins
– For the Challenger 605 aircraft, use SB A605-57-004.
– For the Challenger 604 aircraft, use SB A604-57-006.
– For the Challenger 600 aircraft, use SB A600-0763.
3. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. If no other manual references are given, the procedures that follow
are from the Maintenance Manual, PSP601-2, unless otherwise
specified.
2. All references made to zones, access panels and/or doors, are
from the Maintenance Manual PSP601-2, Chapter 6.
A. Aircraft Setup
(1) Install the safety devices and the warning signs in the applicable positions
and the warning placard on the flap control lever.
(2) Obey all electrical/electronic safety precautions. Refer to Chapter 24-00-00,
ELECTRICAL POWER - Removal/Installation.
(3) Connect the external ac power. Refer to Chapter 12-00-00, SERVICING.
(4) Set the flap control lever to 45 and make sure that the flaps are fully
extended.
(5) Remove the external ac power.  Refer to Chapter 12-00-00, SERVICING.

### Page 9

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 7 of 19
(6) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
(A/C: 3001–3066) (A/C: 5001–5194)
CBP-A 20 20 FLAP MOTOR 1 221
CBP-A 77 77 FLAP CONT 1 221
CBP-B 176 20 FLAP MOTOR 2 222
CBP-B 233 77 FLAP CONT 2 222
CBP-B 188 - BATT CHGR 222
B. PART A: Special Check − Inboard Flap Fasteners on the Hinge Box Wing
Forward Fitting
(1) Do a detailed borescope inspection of the inboard flap fasteners of the
hinge box wing forward fitting of both wings.  Refer to the steps that follow,
Figure 1 and Figure 2.
NOTE: If the fairing is already removed, a visual inspection can be carried
out instead of a borescope inspection.
(a) Examine the orientation of the forward attachments of the inboard flap
hinge boxes at WS 76.50 and WS 127.25.  Refer to Figure 1 and
Figure 2.
Figure 1
(i) If all of the forward fasteners heads of the inboard flap hinge boxes
at WS 76.50 and WS 127.25 of both wings, are correctly oriented
as per Figure 1, proceed to PART C in Paragraph 2.D.

### Page 10

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 8 of 19
Figure 2
(ii) If any of the forward fasteners heads are found missing as per
Figure 2, proceed to PART B in Paragraph 2.C.
(iii) If any of the forward fasteners heads are incorrectly oriented as per
Figure 2 but no fasteners heads are found missing, then the
borescope inspection of the forward inboard flap fasteners, hinge
box wing forward fitting, must be repeated every 100 landings, until
the modification, provided in PART B of this SB is complied with.
As applicable, proceed to PART B or to the Close-out in
Paragraph 2.F.
C. PART B: Modification − Incorrectly Oriented Inboard Flap Fasteners on the
Hinge Box Wing Forward Fitting
(1) Remove fillet seal from perimeter around the forward and aft inboard flap
hinge fairings making contact with the wing surface and the inboard flap
respectively.  Refer to SRM, Chapter 51-57-00, SEALING - Description.
(2) Remove the forward and aft inboard flap hinge-fairings that follow, to gain
access to inboard flap hinge boxes.  Refer to Chapter 6-53-00,
REMOVABLE FAIRINGS - General:
ACCESS DESIGNATION
571-CB (671-CB) Fairing, Forward Inboard Flap Hinge
571-FB (671-FB) Fairing, Forward Inboard Flap Hinge
572-DB (672-DB) Fairing, Rear Inboard Flap Hinge
572-GB (672-GB) Fairing, Rear Inboard Flap Hinge
(3) Obey all the fuel system safety precautions.  Refer to Chapter 28-10-11,
FUEL TANKS - Maintenance Practices.

### Page 11

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 9 of 19
(4) Defuel the aircraft.  Refer to Chapter 12-10-28, FUEL SYSTEM -
Replenishing.
(5) Drain, purge and prepare the main left and right fuel tanks for access.
Refer to Chapter 28-10-11, FUEL TANKS – Maintenance Practices.
(6) Remove the access panels that follow.  Refer to Chapter 6-51-00, ACCESS
PANELS AND DOORS:
ACCESS DESIGNATION
571BB (671BB) Wing Lower Surface – Access Panel
571AB (671AB) Wing Lower Surface – Access Panel
540FB (640FB) Fuel Tank – Access Panels
540GB (640GB) Fuel Tank – Access Panels
NOTE: You can use the Fuel Fumes Detector, Part No. 8320000, as an
alternative to the explosiometer.
(7) Remove and isolate the electrical power from the aircraft.  Refer to Chapter
24-00-00, ELECTRICAL POWER - Maintenance Practices.
(8) Put a DO NOT CONNECT − FUEL TANK MAINTENANCE placard on the
battery.
(9) Put a DO NOT CONNECT − FUEL TANK MAINTENANCE placard on the ac
and the dc ground power receptacles.
(10) Remove and replace each of the HI-LOK/Hi-LITE forward fasteners on
the left and right wing at WS 76.50 and WS 127.25 as per Appendix 1,
PART A, and Figure 3.
(11) If it is not possible to follow all instructions from Appendix 1, Part A or Part B
(REO 600-57-26-001) due to the configuration of the aircraft structures,
submit an SRPSA to Customer Support Engineering (CSE) for evaluation
and to obtain an Approved Repair in order to allow completion of the Service
Bulletin, by email at:  SRPSA@aero.bombardier.com
Figure 3

### Page 12

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 10 of 19
(12) For each wing, disconnect one flap hinge box at a time from the forward
attachment fitting and aft attachment fitting.   Refer to the steps that follow:
CAUTION: ONLY ONE FLAP HINGE BOX IS TO BE DISCONNECTED AT A
TIME.  THE FLAP HINGE BOX MUST BE SUPPORTED DURING
THE MODIFICATION SO AS NOT TO DAMAGE THE FLAPS AND
ATTACHED COMPONENTS.
NOTES: 1. The flap will be supported by the other attached flap hinge
box/arm and both actuators.
2.  To reduce the load on the other attached flap hinge box/arm
and actuators, the flaps should also be supported per best
shop practice or with a bench and padding.  Refer to Figure 4.
Figure 4
(a) Disconnect the inboard flap hinge box (1) at location WS 76.50 and
WS 127.25 as follows:  Refer to Figure 5 and Figure 6.
(i) If necessary, remove and keep the hardware that attach the
bonding jumpers to the flap hinge box (1).
(ii) For the flap hinge box (1) located at WS 76.50 only, do as follows:
(aa) If necessary, disconnect the electrical connector wire from
any attached location on the structure, to allow downward
movement of the flap hinge box.
(bb) Remove and discard the cotter pin (4).  Refer to
Maintenance Manual (PSP 601-2), 20-80-00 Safetying
Devices.
(cc) Remove and keep the nut (5), washer (6) and bolt (7) and
disconnect the control rod (2) from the lever (8) of the flap
position transmitter.
(dd) If necessary, put protective covers on the open ends of the
electrical connector (3) and on the electrical connection of
the position transmitter.

### Page 13

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 11 of 19
(iii) For the flap hinge box (1) located WS 76.50 and WS 127.25,
remove and keep the nuts (9), washers (10) and (11), bolts (12),
and hinge bushings (13), to disconnect the flap hinge box (1) from
the forward attachment fitting.  Refer to Figure 5 and Figure 6.
CAUTION: TO REMOVE AND INSTALL THE HINGE
BUSHINGS USE A C-CLAMP METHOD WITH
THE SUPPORT BLOCK.  USE LIGHT  ANTI-
SEIZE LUBRICANT (LPS-1 OR SIMILAR) IF
THE BUSHINGS ARE SEIZED OR DIFFICULT
TO REMOVE, MAKE SURE THAT THE
LATERAL FORCE DOES NOT EXCEED
200 LBS AND DO NOT USE A HAMMER TO
REMOVE THE BUSHINGS, THIS CAN CAUSE
DAMAGE.
BEFORE YOU INSTALL THE C-CLAMP, MAKE
SURE YOU INSTALL A SUPPORT BLOCK
BETWEEN THE FITTINGS, SHIMS IN ALL
GAPS AS REQUIRED TO AVOID BENDING
AND DAMAGE FROM THE CLAMP FORCE.
OTHER METHOD THAN C-CLAMP COULD BE
USED, PROVIDED LUGS ARE SUPPORTED
AND LATERAL FORCE DOES NOT EXCEED
200 LBS TO AVOID DAMAGE.
Figure 5
(aa) Inspect the hinge bushings, Part No. 600-10300-611 (13) for
damage and/or corrosion, if applicable, replace any damaged
or corroded hinge bushings.
(iv) For the flap hinge box (1) located WS 76.50 and WS 127.25,
remove and keep the nuts (14), washers (15) and (16), bolts (17),
and hinge bushings (18), to disconnect the hinge box (1) from the
aft attachment fitting.  Refer to Figure 5 and Figure 6.
(aa) Inspect the hinge bushings, Part No. 600-10300-609 (18) for
damage and/or corrosion, if applicable, replace any damaged
or corroded hinge bushings.
Install the support block,
manufactured as per
Appendix 2 or an
equivalent commercially
available tool between
the fittings.
Shim all gaps as
required.

### Page 14 (OCR)

ČHÄLLÈNGÉR 601
MODEL CL-600-2A12 & CL-600-2B16
(b) Carefully pull the flap hinge box (1) downward to allow access to the
forward attachment fitting.
FANSATTER  5  FAIRING
BRACKET
SUPPORT
CAUTION: ONLY ONE FLAP HINGE BOX IS TO BE
DISCONNECTED AT A TIME. THE FLAP
HINGE BOX MUST BE SUPPORTED
DURING THE MODIFICATION SO AS NOT
TO DAMAGE THE FLAPS AND ATTACHED
COMPONENTS.
ATTACHMENT FITTING
FORWARD
ATTACHMENT FITTING
10.
Figure 6
Basic Issue: Sep 26/2013  A601-0627
Revision 02: Dec 09/2014  Page 12 of 19

### Page 15 (OCR)

CHALLENGER 601
MODEL CL-600-2A12 & CL-600-2B16
(13) Remove and replace each of the HI-LOK/Hi-LITE AFT fasteners on the left
and right wing at WS 76.50 and WS 127.25 as per Appendix 1, PART B,
and Figure 7.
(14) If it is not possible to follow all instructions from Appendix 1, Part A or Part B
(REO 600-57-26-001) due to the configuration of the aircraft structures,
submit an SRPSA to Customer Support Engineering (CSE) for evaluation
and to obtain an Approved Repair in order to allow completion of the Service
Bulletin, by email at: SRPSA@aero.bombardier.com
• FORWARD ATTACHMENT
HINGE FITTING
Remove and replace each of the
the left and right wing forward  HI-LOK/Hi-LITE AFT fasteners on  FLAP HINGE  ARM
attachment hinge fitting at
WS 76.50 and WS 127.25 as per
Appendix 1, PART B
CAUTION
DO NOT DRILL OFF HEADS OF HI-LOKS/HI-LITES AND
DRIVE SHANK INTO WING-BOX AS THIS COULD CAUSE
SEVERE SCORING OF THE HOLES. REMOVE COLLAR AND
DRIVE HI-LOKS/HI-LITES FROM THREADED END.
FLAP HINGE
BOX
Figure 7
(15) Attach the inboard flap hinge box (1) at locations WS 76.50 and WS 127.25.
Refer to the steps that follow Figure 5 and Figure 6:
(a) Apply one layer of Mastinox 6856K to the hinge bushings (13) and hinge
bushings (18) on installation.
(b) Put the flap-hinge-box (1) in position.
(c) Install the bushings (18) on the flap hinge box (1) and aft attachment
fitting.
(d) Install the bushings (13) on the forward lugs of the flap hinge box (1)
and forward attachment fitting.
Basic Issue: Sep 26/2013  A601-0627
Revision 02: Dec 09/2014  Page 13 of 19

### Page 16

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 14 of 19
(e) Install bolts (17), washers (15) and (16), and nuts (14) to attach the flap
hinge box (1) to the aft attachment fitting.
NOTE: Make sure the sum of the gap measurement between the aft
attachment fitting and lower surface of bolt head (17), and
between the aft attachment fitting and the lower surface of
washer (15), is 0.020 in to 0.105 in (0.508 mm to 2.667 mm).
(f) Install the bolts (12), washers (10) and (11), and nuts (9) to attach
the flap hinge box (1) to the forward attachment fitting.
NOTE: Make sure the sum of the gap measurement between the
forward attachment fitting and lower surface of bolt head
(12), and between the forward attachment fitting and the
lower surface of washer (10), is 0.015 in to 0.060 in
(0.381mm to 1.524 mm).
(g) Torque the nuts (9), and (14) from 30 to 35 lbf in (3.39 to 3.95 Nm).
Refer to Maintenance Manual (PSP 601-2), 20-20-00 Torquing.
(h) Attach the control rod (2) and electrical connector (3) to the flap
position transmitter as follows:
(i) Align the eye of the control rod (2) with the lever (8).
(ii) Install the bolt (7), washer (6) and the nut (5).
(iii) Torque the nut (5), from 20 to 25 lbf in (2.26 to 2.82 Nm).  Refer to
Maintenance Manual (PSP 601-2), 20-20-00 Torquing.
(iv) Install the cotter pin (4).  Refer to Maintenance Manual (PSP 601-2),
20-80-00 Safetying Devices.
(v) Remove the protective covers from the open ends of the electrical
connector (3) and from the electrical connection of the position
transmitter.
(vi) Connect the electrical connector (3) to the flap position transmitter.
NOTE: If detached, attach the electrical connector wire to the
necessary locations on the structure.
(i) Install the bonding jumper on the flap hinge box (1).  Refer to
Maintenance Manual, PSP 601-2, Chapter 57-40-01, FLAP HINGE
BOX, Removal/Installation.
(j) Do the electrical bonding test for the applicable flap hinge box (1).
Refer to Maintenance Manual, PSP 601-2, Chapter 51-80-00,
ELECTRICAL BONDING.

### Page 17

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 15 of 19
(16) Install the access panels that follow:
ACCESS DESIGNATION
571BB (671BB) Wing Lower Surface – Access Panel
571AB (671AB) Wing Lower Surface – Access Panel
540FB (640FB) Fuel Tank – Access Panels
540GB (640GB) Fuel Tank – Access Panels
(17) Remove the DO NOT CONNECT − FUEL TANK MAINTENANCE placard
from the battery.
(18) Remove the DO NOT CONNECT − FUEL TANK MAINTENANCE placard
from the ac and the dc ground power receptacles.
(19) Restore the electrical power on the aircraft.  Refer to Chapter 24-00-00,
ELECTRICAL POWER - Maintenance Practices.
(20) Proceed to the Testing in Paragraph 2.E.
D. PART C:  Correctly Oriented Inboard Flap Fasteners on the Hinge Box
Wing Forward Fitting
If the forward fasteners heads are correctly oriented as per Figure 1, you
already meet the intention of this Service Bulletin and no further action is
required, proceed to the Close-out in Paragraph 2.F.
E. Testing
(1) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
(A/C: 3001–3066) (A/C: 5001–5194)
CBP-A 20 20 FLAP MOTOR 1 221
CBP-A 77 77 FLAP CONT 1 221
CBP-B 176 20 FLAP MOTOR 2 222
CBP-B 233 77 FLAP CONT 2 222
CBP-B 188 - BATT CHGR 222
(2) Connect the external ac power.  Refer to Chapter 12-00-00, SERVICING.
(3) Do an operational test of the inboard flaps to make sure the flap hinge box
assemblies move freely, before installing the flap hinge-fairings.  Refer to
Chapter 27-50-00, WING FLAP SYSTEM – Maintenance Practices.

### Page 18

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 16 of 19
(4) Remove the external ac power.  Refer to Chapter 12-00-00, SERVICING.
(5) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
(A/C: 3001–3066) (A/C: 5001–5194)
CBP-A 20 20 FLAP MOTOR 1 221
CBP-A 77 77 FLAP CONT 1 221
CBP-B 176 20 FLAP MOTOR 2 222
CBP-B 233 77 FLAP CONT 2 222
CBP-B 188 - BATT CHGR 222
(6) Install the forward and aft inboard flap hinge-fairings that follow.  Refer to
Chapter 6-53-00, REMOVABLE FAIRINGS - General:
ACCESS DESIGNATION
571-CB (671-CB) Fairing, Forward Inboard Flap Hinge
571-FB (671-FB) Fairing, Forward Inboard Flap Hinge
572-DB (672-DB) Fairing, Rear Inboard Flap Hinge
572-GB (672-GB) Fairing, Rear Inboard Flap Hinge
(7) Install fillet seal around perimeter of forward and aft inboard flap hinge-
fairings making contact with the wing surface and the inboard flap
respectively.  Refer to SRM, Chapter 51-57-00, SEALING – Description,
Aerodynamic Sealing.
(8) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
(A/C: 3001–3066) (A/C: 5001–5194)
CBP-A 20 20 FLAP MOTOR 1 221
CBP-A 77 77 FLAP CONT 1 221
CBP-B 176 20 FLAP MOTOR 2 222
CBP-B 233 77 FLAP CONT 2 222
CBP-B 188 - BATT CHGR 222
(9) Connect the external ac power.  Refer to Chapter 12-00-00, SERVICING.
(10) Carry out a flap operational test and check corresponding flap position
indications in the flight compartment.  Refer to Chapter 27-50-00, WING
FLAP SYSTEM – Maintenance Practices.

### Page 19

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 17 of 19
F. Close-out
(1) If not already done, remove the tags and close the circuit breakers that
follow:
CB PANEL CB NO. NAME ZONE
(A/C: 3001–3066) (A/C: 5001–5194)
CBP-A 20 20 FLAP MOTOR 1 221
CBP-A 77 77 FLAP CONT 1 221
CBP-B 176 20 FLAP MOTOR 2 222
CBP-B 233 77 FLAP CONT 2 222
CBP-B 188 - BATT CHGR 222
(2) Remove all tools, equipment and unwanted materials from the aircraft.
G. Recording
You can do each PART of this Alert Service Bulletin independently.  When any
PART of this Alert Service Bulletin is completed, make an entry in the aircraft
log and send the attached Incorporation Notice to Bombardier Business Aircraft
Customer Services (BBACS).
This Alert Service Bulletin must be repeated every 100 landings and can only
be closed when:
- The modification in PART B is completed.
or
- PART C is completed to confirm that the forward fasteners heads are
correctly oriented.
In an effort to improve the quality of our technical communications, we are
requesting your feedback.  Please take a moment to fill out our easy on-line
Alert Service Bulletin survey:
http://csefeedback.aero.bombardier.com
4. MATERIAL INFORMATION
A. Kit
When Applicable, submit an SRPSA to Customer Support Engineering (CSE) to
obtain kit and parts details necessary to do PART B of this modification.
B. Parts
When Applicable, submit an SRPSA to Customer Support Engineering (CSE) to
obtain kit and parts details necessary to do PART B of this modification.

### Page 20

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 18 of 19
C. Material
The materials that follow, or equivalent, are necessary to do PART B of this Alert
Service Bulletin.  These can be purchased from a local supplier.  Bombardier
Aerospace does not pay for these consumables.
DESCRIPTION PART
No./NAME
SPECIFICATION QUANTITY SUPPLIER
(See Note)
Corrosion
inhibitor
Compound
Mastinox 6856K - AsNecessary Code: A
Integral Fuel
Tank Sealant
CT: (9 hours) B1/2
(20 hours) B2
P/S 870B MIL-PRF-81733Type II AsNecessary Code: A
Sealant
CT: (12 hours) B1/2
(24 hours) B2
PR1776M B1/2
or
PR1776M B2
- AsNecessary Code: A
Durathane High
Gloss Enamel
CT: (12 hours)
7600 line BAMS 565-002 AsNecessary Code: B
Epoxy Primer
Grey
CT: (2 hours)
4500-P-40B
(16473, FS 595B) BAMS 565-001 AsNecessary Code: B
Conversion
Coating Alodine 1201  MIL-DTL-81706B Type II AsNecessary Code: C
Epoxy Resin
CT: (24 hours)
Hysol
EA9309.3NA AS9354002 AsNecessary Code: C
Fuel Tank
Coatings
(Primer Yellow)
CT: (24 hours)
20P1-10 BAMS 565-010 AsNecessary Code: D
Anti-Seize
Lubricant LPS-1 - AsNecessary Code: E
Brush, Natural or
Synthetic Bristle - - AsNecessary Code: E
Scraper,
Non-Metallic - - AsNecessary Code: E
Spatula - - AsNecessary Code: E
NOTES: 1. Refer to the table that follows for each supplier’s address listed by codes.
2. The Curing Time (CT), if applicable, for each consumable material
is indicated with the description of each product.

### Page 21

MODEL CL-600-2A12 & CL-600-2B16
Basic Issue: Sep 26/2013 A601-0627Revision 02: Dec 09/2014 Page 19 of 19
3. At time of release of this Alert Service Bulletin, the information on
the supplier was valid and accurate.  In the event that this
information has changed, the operator is encouraged to use the
World Wide Web to find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
PRC – Desoto International
5430 San Fernando Road,
PO Box 1800, Glendale,
CA, U.S.A. 91209
Tel.: 1-800-228-5635
Fax: (818)-549-7790
Web Site: www.ppg.com/prc-desoto
Code: B
Tempo Aerospace Inc
205 Fenmar Drive,
Toronto, Ontario, Canada
M9L 2X4
Tel.: 1-416-746-2233
Fax.: 1-416-746-2235
E-mail: sales@tempo-aerospace.com
Web Site: www.tempo-aerospace.com
Code: C
Henkel Corporation
2850 Willow Pass Road
Bay Point, California 94565
Tel.: 1-925-458-8000
Fax: 1-925-458-8030
Web Site: www.henkelna.com
Code: D
AkzoNobel Aerospace Coatings.
1 East Water Street
Waukegan, IL 60085
USA
Tel.: 1-847-623-4200
Fax.: 1-847-625-3200
E-mail: customer.service@akzonobel.com
Web Site: www.akzonobel.com
Code: E
Commercially Available
D. Publications
No publications required.

### Page 22

ALERT SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: A601-0627 ISSUE: Rev. 02 DATED: Dec 09/2014
TITLE: Special Check/Modification – Attachment Fittings – Inboard Flap Hinge Box Forward
Attachment Fittings Fasteners
In an effort to improve the quality of our technical communications, we are replacing
the standard Service Bulletin Evaluation Form with an on-line Service Bulletin
Survey and we are requesting your feedback.  Please take a moment to fill out our
easy on-line Service Bulletin survey:
http://csefeedback.aero.bombardier.com

### Page 23

ALERT SERVICE BULLETIN INCORPORATION SHEET –
“A601-0627”
BOMBARDIER
SUBMISSION Upon completion of the Service Bulletin, please fill-in, fax to
(514) 855-8798 or e-mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier.  If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
     COMPLIED WITH
Alert Service
Bulletin Number
Rev. * Parts
Completed
YES NO N/A Remarks/Reason
A601-0627 02 PART A
“ “ PART B
“ “ PART C
Actual hours to accomplish Service Bulletin:
* NOTES: 1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should be
reported.
Aircraft Serial No.  Aircraft Reg. No.
Airframe Hours:  Airframe Landings
S.B. Incorporation date  Service Order No.
(dd/mm/yy)
Facility Incorporating S.B.
Name Signature Date
                          (dd/mm/yy)Signature not required if sent by E-Mail

### Page 24

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Bombardier Business Aircraft Customer Services (BBACS)
P.O. Box 6087, Station Centre-ville
Montreal, Québec, Canada H3C 3G9
Attention: Customer Support Department, Maintenance Engineering
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
