# Bombardier Service Bulletin 100-24-24

Copy: No revision named ("FAA-2015-0929 SB 100-24-24"), 17 pages: PDF https://openairdocs.org/files/sha256/ed/b7/edb76e8a7000e4b29c106e225e0060dd4cb5e27727320e680129ce7093faafc2; text https://openairdocs.org/service-documents/bombardier/sb-100-24-24/file/edb76e8a7000.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-0929; AD 2015-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-24-24
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-24-24

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-23-07](https://openairdocs.org/ad/2015-23-07.md), effective Dec 22, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-24-24/proposed.md).

## Text (17 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-0929; AD 2015-23-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MODIFICATION - PRIMARY DC-POWER SYSTEM - REROUTING OF THE WIRING
HARNESS AT PRESSURE BULKHEAD FS669.759
The information below is provided for your reference. For full details, please see
corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
        Recommended within 36
        months from this Service
        Bulletin release date (Basic
Issue).
EFFECTIVITY: A/C Serial No. 20003 to 20382, 20384 and 20386
MANPOWER: 4 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin is expected to be the subject of an Airworthiness Directive
which will make it necessary to implement this Service Bulletin.
To place an order for kits, please call Bombardier Aerospace Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
www.cic.bombardier.com
MODEL BD−100−1A10 (CL−300)
ATA 24−31
ELECTRICAL POWER
Basic Issue: Jun 06/2014 100−24−24
Page 1 of 1
This Service Bulletin is available at:

### Page 2

MODIFICATION - PRIMARY DC-POWER SYSTEM - REROUTING OF THE WIRING
HARNESS AT PRESSURE BULKHEAD FS669.759
1. PLANNING INFORMATION
A. Effectivity
BD−100−1A10 aircraft, Serial No. 20003 to 20382, 20384 and 20386.
All other BD−100−1A10 aircraft were scheduled for the modification in production.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent action
changes to make sure that this bulletin can be completed.
B. Reason
In some instances, it was found that a wiring harness, in the aft equipment bay, was
in contact with the hydraulic line. This had resulted in wear on the electrical
harness. There is a small possibility that this could eventually cause an electrical
short circuit or a system malfunction.
SERVICE BULLETIN
www.cic.bombardier.com
MODEL BD−100−1A10 (CL−300)
ATA 24−31
ELECTRICAL POWER
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2014 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jun 06/2014 100−24−24
Page 1 of 14
This Service Bulletin is available at:

### Page 3

This Service Bulletin introduces a modification to reroute the wiring harness to
prevent contact with the hydraulic line.
C. Description
This Service Bulletin gives instructions to:
− Get access to the wiring harness,
− Do the modification to reroute the wiring harness, and
− Do the necessary tests to make sure that the systems operate correctly.
D. Compliance
Recommended within 36 months from this Service Bulletin release date (Basic
Issue).
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA in
accordance with established procedures.
F. Manpower
NOTES: 1. The man−hours given are estimates to help you schedule the tasks
given in this bulletin. The estimates are for direct labor performed by
an experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower estimates, refer to SB
100−00−02.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the labor estimates and should be considered
for planning purposes before you schedule this Service Bulletin.
4 man−hours are necessary to do this modification.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 2 of 14

### Page 4

The labor required to do this Service Bulletin is at no cost if:
− the aircraft is in the new aircraft warranty period at the time of the Service
Bulletin (Basic Issue) release, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled during the compliance time.
G. Material − Cost and Availability
Kit 100K24−24 is necessary to do this modification.
KIT NO. PRICE
100K24−24
Please contact Bombardier Aerospace
Parts Services in Montreal, for delivery
lead times and confirmation of prices.
This kit is available at no cost if:
− the aircraft is in the new aircraft warranty period at the time of the Service
Bulletin (Basic Issue) release, and
− a no−charge purchase order is sent to Bombardier Aerospace during the
compliance time.
For those aircraft out of the new aircraft warranty at the time of the Service Bulletin
release, Smart Parts Plus pays for the kit during the compliance time stated in this
Service Bulletin.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
20X−00−04 M1−G−KIT Portable Bonding Tester,or equivalent
24−00−24 S4933959−501 Tag, Circuit Breaker
− Commercially Available Digital Multimeter
− Commercially Available Wrench, Torque
NOTES: 1. Refer to the BD−100 Illustrated Tool and equipment Manual to make
sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE
equivalents.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 3 of 14

### Page 5

I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Modification Summary, BB100T010748, Rev. C.
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI),
C−100−000−24−0095, Rev. A.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20 and 51.
− Bombardier Aerospace, Kit Drawing K1000070302, Rev. B.
− Bombardier Aerospace, SB 100−00−02, Service Bulletin Description and Policy.
− BD−100 Aircraft Maintenance Manual (AMM), Chapters 6, 24 and 52.
− BD−100 Structural Repair Manual (SRM), Chapter 51.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
None.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 4 of 14

### Page 6

2. ACCOMPLISHMENT INSTRUCTIONS
NOTE: All references made to zones, access panels and/or doors, are from the
BD−100 AMM, Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Open the aft equipment−compartment door, 182GL. Refer to
AMM 52−41−00−010−801.
B. Modification
(1) Remove the Auxiliary DC Power Center (Aux DCPC). Refer to
AMM 24−64−01−000−801.
(2) Stow the disconnected cables out of the way.
(3) Visually examine the wiring harness for wear, where it touches the hydraulic
tube. Refer to Figure 1.
(4) Repair any damage to the wiring harness per Bombardier Aerospace Standard
Practices Manual (SPM). For damage that is more than the repair limits in the
SPM, submit a Service Request for Product Support Action (SRPSA) to
Customer Support Engineering (CSE) for evaluation and to get an Approved
Repair, by email to:
SRPSA@aero.bombardier.com
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 5 of 14

### Page 7 (OCR)

MODEL BD-100-1A10 (CL-300)
WIRE
ELECTRICAL  CHAFING
HARNESS  AREA
A
WIRE CHAFING
AREA
HYDRAULIC
• LINE
CSB2431_001
Harness Contact Location
Figure 1
Basic Issue: Jun 06/2014  100-24-24
Page 6 of 14

### Page 8

(5) Do the modifications at the location shown in Kit Drawing K1000070302, as
follows:
(a) Rework the stand−off, Part No. B0204034AL−10W, supplied in the kit, as
follows:
(i) Enlarge the two mounting holes to make them 0.164 to 0.167 in (4.17
to 4.24 mm) diameter.
(ii) Deburr the holes.
(b) Remove and discard the tiedown strap.
(c) Remove and keep the screw, Part No. NAS1801−3−10, washer, Part No.
NAS1149D0332J, and cable support, Part No, B0816005−10159.
(d) Drill out the rivets, then remove and discard the stand−off, Part No.
B0204034AL−10W. Refer to SRM 51−42−16.
(e) Enlarge the two holes in the vertical beam to make them 0.159 to 0.162 in
(4.04 to 4.11 mm) diameter.
(f) Install two Hi−Lites, Part No. B0206001AG5−2, and collars, Part No.
B0203013−08, in the holes where the stand−off was located.
(g) Drill two holes, for the new stand−off, 0.159 to 0.162 in (4.04 to 4.11 mm)
diameter at the location shown in the vertical beam, Part No. 1005351606.
Refer to Kit Drawing K1000070302, Section A−A.
(h) Install the new reworked stand−off, Part No. B0204034AL−10W, with two
Hi−Lites, Part No. B0206001AG5−3, and collars, Part No. B0203013−08,
on the outboard side of the vertical beam as shown. Refer to Kit Drawing
K1000070302, Section A−A and SRM 51−42−36.
(i) Install the previously removed cable support on the stand−off and attach
with screw, Part No. NAS1801−3−10 and washer, Part No.
NAS1149D0332J.
(j) Attach the wiring harness to the cable support with two new tiedown
straps, Part No. B0816019−003.
(6) Reroute the wiring harness as follows:
(a) Remove and discard the screw, Part No. NAS1801−3−10 and washer,
Part No. NAS1149D0332J, from harness support, Part No. B0816018−11.
(b) Attach the wiring harness to the harness support, Part No. B0816018−11,
with clamp, Part No. B03090A9S13, screw, Part No. NAS1801−3−18,
washer, Part No. NAS1149D0332J, and spacer, Part No.
NAS43DD3−32FC. Make sure that there is a minimum clearance of 0.50
in (12.7 mm) between the electrical harness and the hydraulic tubing.
NOTE: If necessary, loosen and reposition surrounding clamps on the
wiring harness to make sure you have the correct routing and
clearance with the adjacent structure. If the harness does not
have enough slack, clamp Part No. B03090A9S13, screw, Part
No. NAS1801−3−18, washer, Part No. NAS1149D0332J, and
spacer, Part No. NAS43DD3−32FC can be omitted.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 7 of 14

### Page 9

(7) Install the Aux DCPC. Refer to AMM 24−64−01−400−801.
C. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Close the aft equipment−compartment door, 182GL. Refer to
AMM 52−41−00−410−801.
D. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
3. MATERIAL INFORMATION
A. Kits
Kit 100K24−24 is necessary to do this Service Bulletin and contains the parts that
follow:
NEW PART NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
B0203013−08 5 Collar − −
B0204034AL−10W 1 Stand−off − −
B0206001AG5−2 3 Hi−Lite − −
B0206001AG5−3 3 Hi−Lite − −
B0305090A9S13 1 Clamp − −
B0816019−003 2 Strap,Tiedown − −
NAS1149D0332J 3 Washer − −
NAS1801−3−18 1 Screw − −
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 8 of 14

### Page 10

NEW PART NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
NAS43DD3−32FC 1 Spacer − −
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
No parts required.
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier. Bombardier Aerospace does not pay
for these consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Coating,
Chemical
Conversion
Alodine 1000
MIL−C−81706
Class III, Type II,
Method B
As Necessary Code: A
Brush, Paint,
Natural or
Synthetic
Bristle
− − As Necessary Code: B
NOTES: 1. Refer to the table that follows for each supplier’s address listed by
codes.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 9 of 14

### Page 11

2. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Henkel Canada Corporation
2225 Meadowpine Boulevard
Mississauga, Ontario
Canada, L5N 7P2
Tel.: (905) 814−6511
Fax.: (905) 814−6522
www.henkelna.com
Code: B
Commercially Available
D. Publications
No publications required.
MODEL BD−100−1A10 (CL−300)
Basic Issue: Jun 06/2014 100−24−24
Page 10 of 14

### Page 12

K1000070302B_002−PL
MODEL BD−100−1A10 (CL−300)
PLK1000070302 − Kit − Harness Rerouting, Pressure Bulkhead FS669.759
(Sheet 1 of 2, Rev. B)
Basic Issue: Jun 06/2014 100−24−24
Page 11 of 14

### Page 13

K1000070302B_001−PL
MODEL BD−100−1A10 (CL−300)
PLK1000070302 − Kit − Harness Rerouting, Pressure Bulkhead FS669.759
(Sheet 2 of 2, Rev. B)
Basic Issue: Jun 06/2014 100−24−24
Page 12 of 14

### Page 14

K1000070302B−S1−001
K1000070302 − Kit − Harness Rerouting, Pressure Bulkhead FS669.759
(Sheet 1 of 1 , Rev. B)
Basic Issue: Jun 06/2014 100−24−24
Page 13 of 14

### Page 15

K1000070302B−S1−002
K1000070302 − Kit − Harness Rerouting, Pressure Bulkhead FS669.759
(Sheet 1 of 1, Rev. B, continued)
Basic Issue: Jun 06/2014 100−24−24
Page 14 of 14

### Page 16

100−24−24 Basic Jun 06/2014
MODIFICATION − PRIMARY DC−POWER SYSTEM − REROUTING OF
THE WIRING HARNESS AT PRESSURE BULKHEAD FS669.759
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 17

SERVICE BULLETIN INCORPORATION SHEET − "100−24−24"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
100−24−24 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
