# Bombardier Service Bulletin 100-25-21: Revision 02

- Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-1199; AD 2015-26-03 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.
- Document: [Bombardier Service Bulletin 100-25-21](https://openairdocs.org/service-documents/bombardier/sb-100-25-21.md)
- Title as filed: FAA-2015-1199 SB 100-25-21R2
- Pages: 19
- PDF: https://openairdocs.org/files/sha256/ff/e0/ffe06e2c0e870e5780859b6f5d152ac41accd3ccea81d107c5de05aeb02403e0
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-25-21/file/ffe06e2c0e87

## Text

Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

100-25-21  
 Page 1 of 1 
SERVICE BULLETIN 
REVISION TRANSMITTAL SHEET 
MODEL BD-100-1A10 (CL-300) 
Discard Revision 01 of this Service Bulletin dated May 02/2013 and replace in its 
entirety with this Revision 02. 
 
 
Service Bulletin No. 100-25-21
Date of Basic Issue Jun 30 /2008
Revision No. 01 Dated Ma y 02/2013
Revision No. 02 Dated Jul 25 /2013
 
 
For action applicable to aircraft on which the Basic Issue of this Service Bulletin 
was done, refer to the retroactive action box on Page 1 of this Service Bulletin. 
This revision is issued to: 
1. Add, in the Summary Sheet, a Note in reference to Airworthiness Directive, TCCA 
AD # CF-2010-06. 
2. Add, in Paragraph 1.K., a refer ence to Airworthiness Directive,  
TCCA AD # CF-2010-06. 
3. Add, in Paragraph 1.K., a refer ence to Advisory Wire AW300-21-0083. 
4. Change, in Paragraph 3.C., the supplier information for Code B. 
5. Make miscellaneous minor changes, as necessary, with no change of context.

### Page 2

Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013 Page 1 of 1 
SERVICE BULLETIN SUMMARY 
This Service Bulletin is available at: 
www.cic.bombardier.com  
BD-100-1A10 (CL-300) 
ATA 25-80 
EQUIPMENT / FURNISHINGS 
SPECIAL CHECK/REWORK – INSULATION – REMOVAL OF POSSIBLE FOREIGN 
MATERIAL IN THE AREA OF THE SAFETY VALVES  
The information below is provided for your reference.  For full details, please see 
corresponding paragraph contained within this bulletin. 
RECOMMENDED 
SPECIFIED TIME COMPLIANCE 
COMPLIANCE TIME 
At the next maintenance opportunity, 
but no later than July 2014 
EFFECTIVITY: A/C Serial No. 20003 to 20123, 20126, 20127, 20129 to 20133, 20135 
to 20138, 20140 to 20142, 20144, 20145 and 20147 
MANPOWER: See Paragraph 1.F. 
CONTINUED AIRWORTHINESS (CAW)  
FLEET CAMPAIGN 
YES  NO  
KITS and/or PARTS YES  NO  
TOOLING/GSE YES  NO  
PLANNING INFORMATION:  See important 
information at the start of Paragraph 1. YES  NO  
DEDICATED SCHEDULE YES  NO  
PREREQUISITE SERVICE BULLETINS: N/A 
NOTE: This Service Bulletin has an Airworthiness Directive, TCCA AD # CF-2010-06, 
which requires a revised maintenance schedule, cleaning of the safety valves 
and surrounding area and modification of the safety valves. 
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at: 
514-855-2999 or 1-866-538-1247

### Page 3

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this 
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards. 
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or 
by any means without the prior written consent of Bombardier Inc. and/or its affiliates. 
© 2008 - 2013 Bombardier Inc.  All rights reserved 
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries. 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 1 of 14 
SERVICE BULLETIN 
This Service Bulletin is available at: 
www.cic.bombardier.com  
BD-100-1A10 (CL-300) 
ATA 25-80 
EQUIPMENT / FURNISHINGS 
SPECIAL CHECK/REWORK – INSULATION – REMOVAL OF POSSIBLE FOREIGN 
MATERIAL IN THE AREA OF THE SAFETY VALVES 
 
RETROACTIVE ACTION 
THE ACTION THAT FOLLOWS IS RECOMMENDED FOR AIRCRAFT ON WHICH 
THE BASIC ISSUE OF THIS SERVICE BULLETIN WAS DONE:  
Do the Special Check/Rework as given in Paragraph 2.B., within the Compliance Time 
given in Paragraph 1.D. 
1. PLANNING INFORMATION 
A. Effectivity 
BD-100-1A10 aircraft, Serial No. 20003 to 20123, 20126, 20127, 20129 to 20133, 
20135 to 20138, 20140 to 20142, 20144, 20145 and 20147. 
NOTES: 1. Refer to Service Bulletin 100-25-14 for BD-100-1A10 aircraft,  
Serial No. 20124, 20125, 20128, 20134, 20139, 20143, 20146, 20148 
to 20173, 20176 and 20177. 
2. The instructions given in this Service Bulletin are only applicable to 
the systems and parts installed at the time of delivery of the aircraft  
or as changed by Bombardier Aerospace Service Bulletin(s).  
Before you do this bulletin, examine all STC, STA or equivalent  
action changes to make sure that this bulletin can be completed.

### Page 4

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 2 of 14 
B. Reason 
This Service Bulletin provides instructions to inspect for presence of foreign 
material in the area of the safety valves and contamination on the safety valves. 
Some events of cabin depressurization were reported and investigation 
demonstrated presence of black foam and incorrect installation of the insulation 
blankets in the area of the safety valves.  Any loose debris in this area could 
possibly block the safety valves and lead to cabin depressurization.  
Further events of cabin depressurization were reported following incorporation of 
the Basic Issue of this Service Bulletin, thus, this revision gives improved 
instructions to clean the area in front of the safety valves. 
C. Description 
This Service Bulletin gives instructions to: 
– Get access to the safety valves,  
– Inspect for presence of foreign material in the area surrounding the safety 
valves, 
– Remove foreign material, as required, 
– Inspect safety valves for presence of contamination. 
– Inspect for correct installation of the insulation blankets in safety valve area. 
– Clean or replace safety valve(s), as necessary, and 
– Do the necessary tests to make sure the replaced safety valve(s) operate(s) 
correctly, as necessary. 
D. Compliance 
Revision 01 or subsequent, of this Service Bulletin is recommended at the next 
maintenance opportunity, but no later than July 2014. 
NOTE: This Service Bulletin is in reference to Advisory Wire AW300-21-0083.

### Page 5

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013 Page 3 of 14 
E. Approval 
The technical content of this Service Bulletin has been approved under  
the authority of Transport Canada Civil Aviation (TCCA) Design Approval 
Organization (DAO) No. DAO #93-Q-02. 
NOTES: 1. The technical content of this  Service Bulletin is accepted by the  
FAA under the Canada/USA bilateral Aviation Safety Agreement. 
2. The technical content of this Service Bulletin is accepted by the  
JAA and by EASA in accordance with established procedures. 
F. Manpower 
NOTES: 1. The man-hours given are es timates to help you schedule the tasks  
given in this bulletin.  The estimates are for direct labor performed by  
an experienced crew and do not include the time for familiarization, 
planning, aircraft preparation in hangar such as towing and 
positioning of scaffolds, removal of interior furnishings, repainting, 
supervision and inspection. 
For more information related to the manpower estimates, refer to  
SB 100-00-02. 
2. This Service Bulletin may require consumable materials that have 
specific curing times (refer to Paragraph 3.).  The accumulated curing 
time is not included in the labor estimates and should be considered 
for planning purposes before you schedule this Service Bulletin. 
2 man-hours are necessary to do this special check/rework. 
2 additional man-hours are necessary to replace each safety valve, as required. 
Bombardier Aerospace pays for the labor to do this special check/modification 
until July 2014.

### Page 6

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 4 of 14 
G. Material – Cost and Availability 
If contamination that cannot be cleaned off is found per Paragraph 2.B.(4)(e),  
up to two safety valves, Part No. 81141A010303, may be necessary to do this 
Service Bulletin.  The valves are available at no cost if a no-charge purchase 
order is sent to Bombardier Aerospace Parts Services before July 2014.  For 
material data, refer to Paragraph 3. 
Send the removed safety valve(s), Part No. 81141A010303, to one of the two 
addresses given below in exchange for replacement unit(s): 
Learjet – Core Returns 
8219 West Irving, Bldg 9, Dock 9, 
Wichita, KS 67209 
USA 
or 
Distribution Centre Frankfurt – Core Returns 
Bombardier Aerospace Germany GmbH 
Hans-Boeckler-Strasse 9 
GROSS-GERAU Hesse 64521 
Germany 
Refer to your Material Return Authorization (MRA) form to find the applicable 
return address. 
NOTES: 1. Bombardier Aerospace is ma intaining a rotable pool of replacement 
safety valves, to be supplied to the operators under the terms and 
conditions given below: 
– The removed safety valves(s), Part No. 81141A010303, must be 
returned to one of the addresses given above in less than 10 days 
of receipt of replacement unit(s) with documentation showing the 
serial number of the aircraft. 
– If the removed safety valves(s), Part No. 81141A010303, are not 
returned in less than 10 days, the operator will be charged for the 
replacement unit(s). 
2. On the no-charge purchase order, write “For incorporation of  
SB 100-25-21. 
During or after the above free period, Smart Parts Plus does not pay for 
the parts.

### Page 7

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013 Page 5 of 14 
H. Tooling  
The equipment and tools listed below may be necessary to do this special  
check/rework: 
GSE REFERENCE NO. PART NO. DESCRIPTION 
20X-00-04 M1-G-KIT Portable Bonding 
Tester, or equivalent 
21C-31-04 SBE2221 Cabin Pressurization 
Safety Valve – Test Kit 
21C-31-05 MIL-H-5593-4-156-1OE  Adapter Hose Cabin 
Pressurization Safety 
Valve – Test Kit 
34C-10-04 ADTS-405F Air Data Test Set 
- Commercially Available Stopwatch 
- Commercially Available Wrench, Torque 
NOTES: 1. Refer to the BD-100 Illustra ted Tool and Equipment Manual (ITEM) to 
make sure that you use the correct equipment configuration. 
2. Refer to the Liability Statement  in the ITEM for acceptable GSE 
equivalents. 
3. This list is provided for quick reference.  In case of discrepancy 
between this list and the tools called in the SPM, WM, Chapter 20, 
then the tools called in the SPM, WM prevail.  Other approved 
alternative tools are acceptable and can also be used. 
I. Weight and Balance 
No change. 
J. Electrical Load Data 
No change.

### Page 8

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 6 of 14 
K. References 
– TCCA Airworthiness Directive, CF-2010-06. 
– Advisory Wire AW300-21-0083. 
– Bombardier Aerospace, Restriction and/or Special Instruction (RSI),  
C-100-000-21-0084, Rev. C. 
– BD-100 Aircraft Maintenance Manual (AMM), Chapters 6, 21, 25 and 51. 
– BD-100 Supplemental Maintenanc e Manual (SMM), Chapter 25. 
– BD-100 Aircraft Illustrated Part s Catalog (AIPC), Chapter 21. 
– Liebherr Aerospace Component Maintenance Manual (CMM), 21-31-40. 
– Service Not Incorporated Engi neering Order (SNIEO), 1005351038 S1. 
– Bombardier Aerospace, Installation Drawing M2013282. 
– Bombardier Aerospace, SB 100- 00-02, “Description and Policy”. 
L. Other Publications Affected 
None. 
M. Equivalent Service Bulletin 
None. 
2. ACCOMPLISHMENT INSTRUCTIONS 
NOTES: 1. All TASKs given in the proc edures that follow are from the BD-100, 
Aircraft Maintenance Manual unless otherwise specified. 
2. All references made to zones, access panels and/or doors, are from  
the BD-100 Aircraft Maintenance Manual, Chapter 6. 
A. Aircraft Setup 
Remove the baggage compartment headliner to get access to the safety valve area 
and the insulation blankets between the pressure bulkhead (FS 669.76) and the 
lavatory bulkhead (FS 629.25).  Refer to SMM Chapter 25-53-03.

### Page 9

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013 Page 7 of 14 
B. Special Check/Rework 
(1) Visually inspect for presence of: 
– Foreign material in the area surrounding the safety valves. 
– RTV silicone on all visible surfaces of the safety valves.  Refer to Figure 1. 
– Contamination (e.g. RTV, dust, lint) on the pressure sensing port.  Refer to 
Figure 1. 
– RTV or foam on the bulkhead stru cture.  Refer to Figure 1. 
– Tape or insulation within approximatel y 0.5 in (12.7 mm) minimum from the 
safety valves opening.  Refer to Figure 1. 
– Loose material, loose insulation, foam or any other foreign material in any 
part of the safety valve compartment and in the channel between the 
lavatory grill and the safety valve (above the baggage compartment 
ceiling). 
(2) Remove any foreign material, loose ma terial, loose insulation and foam in  
the area surrounding the safety valves, in the safety valve compartment  
and in the channel between the lavatory grill and the safety valve (above  
the baggage compartment ceiling).  There must be a clear path between  
the lavatory grill and the safety valves. 
(3) If RTV is found on the visible surfaces of the safety valves or on the Aft 
Pressure Bulkhead near the safety valves, do as follows: 
(a) Remove the RTV using a non-metallic scraper. 
(b) Clean the surfaces.  Refer to TASK 51-25-00-110-801. 
(c) If the RTV cannot be removed from the visible surfaces of the safety 
valves, do as follows: 
(i) Remove the safety valve, Part No. 81141A010303.  Refer to  
TASK 21-31-09-000-801. 
(ii) Send the safety valve, to the address shown in Paragraph 1.G. 
(iii) Install a new safety valve, Part No. 81141A010303.  Refer to  
TASK 21-31-09-400-801. 
(iv) Do the electrical bonding test of the safety valve.  Refer to SPM 
TASK 51-80-00-760-801. 
NOTE: Make sure that the resistance value is not more than  
0.5 ohm measured between the safety valve and the  
aircraft primary structure. 
(4) To check if there is any contaminati on (e.g. RTV, dust or lint) on the safety 
valve pressure sensing ports, do as follows: 
(a) Gently press the safety valve plunger to its fully open position to expose 
the outside diameter of the pressure sensing port conduit.  Refer to  
Figure 1.

### Page 10

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 8 of 14 
(b) Visually inspect the outside diameter  of the pressure sensing port conduit 
for the presence of contamination and release the safety valve plunger. 
(c) Visually inspect the inside diameter of the pressure sensing port conduit 
for presence of contamination. 
(d) For safety valves with no presence of contamination on the inside or 
outside diameter of the pressure sensing port conduit, go to Paragraph 
2.B.(5). 
(e) For safety valves with the presence of RTV or the presence of dust or lint 
contamination on the inside or outside diameter of the pressure sensing 
port conduit, do as follows: 
(i) Remove the safety valve, Part No. 81141A010303.  Refer to  
TASK 21-31-09-000-801. 
(ii) Send the safety valve, to the address shown in Paragraph 1.G. 
(iii) Install a new safety valve, Part No. 81141A010303.  Refer to  
TASK 21-31-09-400-801. 
(iv) Do the electrical bonding test of the safety valve.  Refer to SPM 
TASK 51-80-00-760-801. 
NOTE: Make sure that the resistance value is not more than  
0.5 ohm measured between the safety valve and the  
aircraft primary structure. 
(5) Remove any loose tape, loose insulation and frayed insulation found within 
approximately 0.5 in (12.7 mm) from the safety valve openings. 
(6) If the minimum area of 0.5 in (12.7 mm) surrounding the safety valves cannot 
be cleared, trim the insulation as far as possible from the opening of the safety 
valve and secure with PSA tape, Part No. 70-1C-2.  Refer to SPM  
TASK 51-28-01-390-803:

### Page 11 (OCR)

RDI
MODEL BD-100-1A10 (CL-300)
0.5 in (12.7 mm) Area around
Safety Valve Opening
CP9P1
Restore the insulation to
production configuration
Refer to Figures 2, 3 and 4
Plunger
Remove ALL foam from
Safety Valve Compartment
Pressure
Sensing Port
View A
View of Inspection Area around Safety Valves
Figure 1
Basic Issue: Jun 30/2008  100-25-21
Revision 02: Jul 25/2013  Page 9 of 14

### Page 12

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 10 of 14 
(7) Make sure that the insulati on blankets above the baggage compartment 
headliner are installed correctly. 
(a) Make sure that the insulation blankets do not hang down in the air 
channel between the lavatory grill and the safety valves.  Refer to  
Figures 2 and 3. 
(b) Make sure that the adhesive tape is bonded correctly. 
C. Testing 
If one or both safety valves were replaced, do the functional test of the positive 
and negative pressure relief.  Refer to TASK 21-31-09-720-801. 
D. Close-out 
(1) Remove all tools, equipment and unwanted materials from the aircraft. 
(2) Close the safety valve access panel. 
E. Recording 
When this Service Bulletin is completed, make an entry in the aircraft log and 
send the attached Incorporation Notice to Bombardier Business Aircraft Customer 
Services (BBACS). 
In an effort to improve the quality of our technical communications, we are 
requesting your feedback.  Please take a moment to fill out our easy on-line 
Service Bulletin survey: 
http://csefeedback.aero.bombardier.com

### Page 13

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013 Page 11 of 14 
3. MATERIAL INFORMATION 
A. Kit 
No kit is necessary to do this Service Bulletin. 
B. Parts 
The part that follows may be necessary to do this Service Bulletin and is available  
from Bombardier Aerospace Parts Services, Montreal: 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS -
DISPOSITION 
81141A010303 Up to 2 Safety Valve 81141A010303 Refer to 
Paragraph 1.G. 
NOTE: The part number for the item lis ted above is subject to change without 
revision to this Service Bulletin.  In case of discrepancy between this list 
and any other list, the Illustrated Parts Catalog prevails and shall be used 
to determine the latest part number. 
C. Material 
The consumable materials that follow, or equivalent, may be necessary to do this 
Service Bulletin.  These can be purchased from a local supplier.  Bombardier 
Aerospace does not pay for these consumables. 
DESCRIPTION PART 
No./NAME 
SPECIFICATION QUANTITY SUPPLIER
(See Note)
Acrylic 
Conformal 
Coating  
CT: 24 hours 
Humiseal Type 1B15 As 
Necessary 
Code: A 
Tape, Pressure 
Sensitive 
70-1C-2” - As 
Necessary 
Code: B 
Solvent HFE71DA - As 
Necessary 
Code: C 
Brush, Paint, 
Natural or 
Synthetic 
Bristle 
- - As 
Necessary 
Code: D 
Lockwire - Monel, 0.032 in 
(0.81 mm) 
As 
Necessary 
Code: D 
Scraper, 
Non-metallic 
- - As 
Necessary 
Code: D 
Solvent - TT-1-735 
Grade A or B 
As 
Necessary 
Code: D

### Page 14

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Jun 30/2008 100-25-21 
Revision 02: Jul 25/2013  Page 12 of 14 
NOTES: 1. Refer to the table that follo ws for each supplier’s address listed by  
codes. 
2. The Curing Time (CT), if applicable, for each consumable material  
is indicated with the description of each product. 
3. At time of release of this Service Bulletin, the information on the 
supplier was valid and accurate.  In the event that this information 
has changed, the operator is encouraged to use the World Wide Web 
to find a local supplier. 
SUPPLIERS ADDRESSES BY CODES 
Code: A 
Humiseal Division of Chase Corp. 
128 First Street 
Pittsburgh, PA 15238 
U.S.A. 
Tel.: (8660) 932-0800 
Web Site: www.humiseal.com 
Code: B 
E&H Laminating & Slitting Co. 
138 Grand Street 
Paterson, N.J. 07501 
U.S.A. 
Tel.: (973) 345-1725 
Fax: (973) 345-3224 
Web Site: www.ehlam.com 
Code: C 
3M Center 
2501 Hudson Road 
Maplewood, Minnesota 55144-1000 
U.S.A. 
Tel.: (888) 364-3577 
Web Site: www.3m.com 
Code: D 
Commercially Available 
D. Publications 
No publications required.

### Page 15

Baggage Compartment Air Channel 
Figure 2 
 
Basic Issue: Jun 30/2008 
Revision 02: Jul 25/2013 
100-25-21
Page 13 of 14
 
 
SB100-25-050-13282-C-S1 
A 
A 
A-A
BLANKET
(FOAM)
(REF)
FIRST LAYER OF INSULATION (REF)
SECOND LAYER OF INSULATION (REF)
(AIR CHANNEL)
BAGGAGE HEADLINER ASSY
SAFETY VALVE
(OVERHEAD PANEL LIGHT AND SMOKE DETECTOR REMOVED FOR CLARITY)
MESH
BLANKET
(FOAM)
(REF)
PSA TAPE
(BOTH SIDES)
SAFETY VALVE

### Page 16 (OCR)

Lavatory Bulkhead
Mesh Assembly  FS 629.25
Pressure Bulkead (with Safety Valves)  FS 669.76  PSA Tape
• PSA Tape  Mesh Assembly  Ducts
• 1.0 in (25 mm)  Air Channel
FORWARD →
Cross Section through Air Channel
Figure 3
Basic Issue:  Jun 30/2008  100-25-21
| Revision 02: Jul 25/2013  Page 14 of 14

### Page 17

SERVICE BULLETIN EVALUATION FORM 
(Your ideas will help us provide better bulletins) 
SERVICE BULLETIN: 100-25-21 ISSUE: Rev. 02 DATED: Jul 25/2013 
  
TITLE: Special Check/Rework – Insulation – Removal of Possible Foreign Material in the Area 
of the Safety Valves 
 
 
 
 
 
 
 
In an effort to improve the quality of our technical communications, we are replacing 
the standard Service Bulletin Evaluation Form with an on-line Service Bulletin 
Survey and we are requesting your feedback.  Please take a moment to fill out our 
easy on-line Service Bulletin survey:   
 
 
 
 
 
http://csefeedback.aero.bombardier.com

### Page 18

SERVICE BULLETIN INCORPORATION SHEET – “100-25-21” 
 
BOMBARDIER 
SUBMISSION Upon completion of the Service Bulletin, please fill-in, fax to 
(514) 855-8798 or e-mail to Fracas at fracas.montreal@aero.bombardier.com 
 
If your aircraft is registered on CAMP and you are reporting to them, 
please do not send the incorporation sheet to Bombardier. If your aircraft 
is on another tracking system, please contact Bombardier to make 
arrangements for automated data submission. 
 
 
           COMPLIED WITH  
 Service Bulletin 
Number 
 Rev.  * Parts 
Completed 
YES NO N/A Remarks/Reason 
 100-25-21  02  -     
 -  -  -     
 -  -  -     
 
 Actual hours to accomplish Service Bulletin:    
 
* NOTES:  
 
 
  
  
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, 
C, D, etc.) which can be carried out separately, indicate only those parts 
completed at this time. 
2. For repetitive checks (usually PART A) only the initial check should be reported 
unless otherwise stated in the Service Bulletin. 
3. When more than one part is carried out at the same time, each part should be 
reported. 
 
 Aircraft Serial No.   Aircraft Reg. No.   
 Airframe Hours:   Airframe Landings   
 S.B. Incorporation date   Service Order No.   
  (dd/mm/yy)  
 Facilit y Incorporating S.B. 
 Name  Signature  Date  
                               (dd/mm/yy) 
 
Signature not required if sent by E-Mail

### Page 19

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --  
 
 
 
 
 
Bombardier Business Aircraft Customer Services (BBACS) 
P.O. Box 6087, Station Centre-ville 
Montréal, Québec, Canada H3C 3G9 
 
Attention: Customer Support Department, Maintenance Engineering 
 
 
 
 
 
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
