# Bombardier Service Bulletin 100-25-35

Copy: Revision 02 ("SB100-25-35-rev02"), 35 pages: PDF https://openairdocs.org/files/sha256/cd/db/cddb003239169da5b6bbb640cbd7637a04446d6269698e68d13fd8daa516ae87; text https://openairdocs.org/service-documents/bombardier/sb-100-25-35/file/cddb00323916.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-1469; AD 2024-16-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-25-35
- Latest revision known: 100-25-35, Revision 02, dated January 11, 2016 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-25-35

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-16-04](https://openairdocs.org/ad/2024-16-04.md), effective Oct 23, 2024: Revisions 01 and 02

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-25-35/proposed.md).

## Text (35 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-1469; AD 2024-16-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

100-25-35Page 1 of 1
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
MODEL BD-100-1A10 (CH-300)
Discard the Revision 01 of this Service Bulletin dated Sep 23/2013 and the
Information Sheet dated Aug 04/2014, and replace in its entirety with this Revision 02.
Service Bulletin No. 100-25-35
Date of Basic Issue Nov 15/2012
Revision No. 01 Dated Sep 23/2013
Revision No. 02 Dated Jan 11/2016
This revision has no effect for aircraft on which the Basic Issue and Revision 01
of this Service Bulletin was done thus no other action is necessary.  Do not sign
the log book if you have not done this revision.  Keep the previous log book
entry.  You may make an entry as “Not Applicable” for this revision.
This revision is issued to:
1. Revise the Service Bulletin Summary Sheet, to add the TLMC reference.
2. Add, in Paragraph 1.H., a statement for the tools and equipment that are necessary.
3. Change, in Paragraph 2.B.(7)(k), the part no. of the fuse.
4. Change, in Paragraph 2.E.(7), the part no. of the fuse.
5. Change, in Paragraph 3.A., in Kit 100K25-35B, the quantity of fuse holder, Part No.
HFA-R, to 2.
6. Add, in Paragraph 3.A., in Kit 100K25-35B, a reference to fuse, Part No. MDA-5-R.
7. Incorporate the Information Sheet dated Aug 04/2014 that informed operators of a
typographical error in Paragraph 3.A., in the parts list of Kit 100K25-35B.
8. Make miscellaneous minor changes, as necessary, with no change of context.

### Page 2

Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 1 of 1
SERVICE BULLETIN SUMMARYThis Service Bulletin is available at:
www.cic.bombardier.com
BD-100-1A10 (CH-300)
ATA 25-53
EQUIPMENT/FURNISHINGS
MODIFICATION – BAGGAGE COMPARTMENT –
MODIFICATION TO THE LH & RH BAGGAGE BAY HEATER INSTALLATIONS AND
REACTIVATION OF THE LH BAGGAGE BAY HEATER AFTER MODIFICATION AND
RE-IDENTIFICATION AS PART NO. 3436-07
The information below is provided for your reference.  For full details, please
see corresponding paragraph contained within this bulletin.
RECOMMENDEDSPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 60 months of this
Service Bulletin release date (Basic Issue)
EFFECTIVITY: A/C Serial No. 20003 to 20364, 20366, 20367, 20369 and 20372
MANPOWER: Up to 12 man-hours (Refer to Paragraph 1.F.)
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN
YES NO
TLMC, CH 5 AFFECTED YES NO
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION:  See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at:
514-855-2999 or 1-866-538-1247

### Page 3

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
© 2012 - 2016 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 1 of 30
SERVICE BULLETINThis Service Bulletin is available at:
www.cic.bombardier.com
BD-100-1A10 (CH-300)
ATA 25-53
EQUIPMENT/FURNISHINGS
MODIFICATION – BAGGAGE COMPARTMENT –
MODIFICATION TO THE LH & RH BAGGAGE BAY HEATER INSTALLATIONS AND
REACTIVATION OF THE LH BAGGAGE BAY HEATER AFTER MODIFICATION AND
RE-IDENTIFICATION AS PART NO. 3436-07
1. PLANNING INFORMATION
A. Effectivity
BD-100-1A10 aircraft, Serial No. 20003 to 20364, 20366, 20367, 20369 and 20372.
All other BD-100-1A10 aircraft are scheduled for the modification before delivery.
NOTE: The instructions given in this Service Bulletin are only applicable to
the systems and parts installed at the time of delivery of the aircraft
or as changed by Bombardier Aerospace Service Bulletin(s).
Before you do this bulletin, examine all STC, STA or equivalent
action changes to make sure that this bulletin can be completed.
B. Reason
Alert Service Bulletin A100-25-30, which has an Airworthiness Directive,
TCCA AD # CF-2009-38 or FA AD # 2009-25-13, which require deactivation
of the LH baggage compartment heater if a heater mat Part No. 3436-06-1/0
is installed, was released in July 2009 to deactivate the left hand baggage
heater.  This was done to prevent over-heating of the baggage bay liner.
This Service Bulletin introduces a modification for the reactivation of the left
hand baggage heater.  It modifies and re-identifies the LH heater mat with a
new Part No.  It installs spacers between the LH sidewall panel and the
heater mat and it also connects the LH and RH heater mats in series to
reduce the power.  This will prevent overheating because the heat will be
transmitted at a lower power rate to the heater mats.
This Service Bulletin also gives instruction to install a coupling nut heater on
the water line located under the water tank.

### Page 4

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 2 of 30
C. Description
This Service Bulletin gives instructions to:
– Get access to the baggage compartment,
– Do the Baggage Bay Heater Placards installation in accordance with
Bombardier Aerospace, Drawing, BAS68038168,
– Do the Coupling Nut Heater installation under the water tank in accordance
with Bombardier Aerospace, Drawing, BAS68038169,
– Do the heater mat modification and identify as Part No. 3436-07,
– Do the LH baggage heater installation modification in accordance with
Bombardier Aerospace, Drawing, BAS68038170 or BAS68038171,
– Do the electrical modification of the heater mats wiring in accordance with
Bombardier Aerospace, Drawing, BAS68028059, and
– Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended within 60 months from this Service Bulletin release date
(Basic Issue).
E. Approval
The technical content of this Service Bulletin has been approved under
the authority of Transport Canada Civil Aviation (TCCA).
NOTES: 1. The technical content of this Service Bulletin is accepted by the
FAA under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by the
JAA and by EASA in accordance with established procedures.
F. Manpower
NOTES: 1. The man-hours given are estimates to help you schedule the
tasks given in this bulletin.  The estimates are for direct labor
performed by an experienced crew and do not include the time
for familiarization, planning, aircraft preparation in hangar such as
towing and positioning of scaffolds, removal of interior
furnishings, repainting, supervision and inspection.
For more information related to the manpower estimates, refer to
SB 100-00-02.
2. This Service Bulletin may require consumable materials that
have specific curing times (refer to Paragraph 3).  The
accumulated curing time is not included in the labor estimates
and should be considered for planning purposes before you
schedule this Service Bulletin.

### Page 5

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 3 of 30
Up to 12 man-hours may be necessary to do this modification.  These hours
are broken down as follows:
– 10 man-hours are necessary to do the modification of this Service Bulletin.
– An additional 2 man-hours are necessary to do the sidewall panel
modification as instructed in Paragraph 2.C., for aircraft Serial No. 20124,
20125, 20128, 20134, 20139, 20143, 20146 and 20148 to 20215.
The labor required to do this Service Bulletin is at no cost for aircraft in
Completion Warranty at the time of release of Alert Service Bulletin
A100-25-30 (Basic Issue, released on July 20th, 2009) if:
(i) the work is done at Bombardier Business Aviation Services
(BBAS) or Authorized Service Facilities (ASF), and
(ii) this Service Bulletin is scheduled in less than 60 months from its
release date (Basic Issue).
G. Material - Cost and Availability
The kits listed in Paragraph 3.A., may be necessary to do this Service Bulletin.
Refer to the table that follows for the applicable aircraft effectivity:
KIT/PART NO. ITEM PRICE AIRCRAFT
EFFECTIVITY
100K25-35 Kit Please contactBombardier
Aerospace Parts
Services, in
Montreal, for
delivery lead times
and confirmation
of prices.
20003 to 20284, 20286,
20288 and 20301
100K25-35A Kit 20003 to 20259
100K25-35B Kit 20003 to 20364, 20366,20367, 20369 and 20372
In addition to the kits shown above, the parts listed in Paragraph 3.B. may be
necessary to do this modification.
These kits and parts are available at no cost for aircraft in and out of warranty
if a no-charge purchase order is sent to Bombardier Aerospace in less than
60 months, from this Service Bulletin release date (Basic Issue).
During or after the above free period, Smart Parts Plus does not pay for the kits
and parts.

### Page 6

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 4 of 30
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
GSE 24-00-24 S4933959-501 Tag, Circuit Breaker
GSE 20X-00-04 M1-G-KIT Portable bonding tester
Commercially Available - Clamp on, Ammeter
Commercially Available - Wire, Stripper
(14 AWG wire)
Commercially Available - Heat Gun
Commercially Available
ERG-4002 Thomas & Betts,
Sta-Kon CrimperWT-112M
Commercially Available - Digital Multimeter
(range 0.1Ω to 50 MΩ)
Refer to the Standard Practices Manual (SPM), Wiring Manual (WM), Chapter 20,
and the table that follows for the tools applicable to the wiring modification:
LUG/CONTACT
TOOL (See NOTE 3)
CRIMP POSITIONER INSERTION EXTRACTION
M39029/22-191 M22520/7-01 M22520/7-11 M81969/14-01(GREEN) M81969/14-01(WHITE)
M39029/22-605 M22520/1-01 M22520/1-16 M81969/16-03(YELLOW) M81969/16-03(WHITE)
NOTES: 1. Refer to the BD-100 Illustrated Tool and Equipment Manual (ITEM)
to make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE
equivalents.
3. This list is provided for quick reference.  In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail.  Other approved
alternative tools are acceptable and can also be used.

### Page 7

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 5 of 30
I. Weight and Balance
A/C SERIAL NO. WEIGHT MOMENT
20003 to 20284,
20286, 20288, and
20301
(Kit 100K25-35)
+0.146 pound (0.066 kg) +93.41 pound-inches
(0.067 kgm)
20003 to 20259
(Kit 100K25-35A)
+0.000 pound (0.000 kg) +0.08 pound-inches
(0.000 kgm)
20003 to 20364,
20366, 20367,
20369 and 20372
(Kit 100K25-35B)
+0.304 pound (0.138 kg) +193.14 pound-inches
(0.139 kgm)
J. Electrical Load Data
This modification decreases the continuous load as follows:
BUS AMPS KW KVAR
28 V dc
R AUX BUS
17.7 amps
(continuous)
- -
K. References
– Transport Canada (TC) Supplemental Type Certificate (STC), SA04-112.
– ACS – NAI, Modification Data Summary (MDS), G874000 Rev. A.
– TCCA Airworthiness Directive, # CF-2009-38.
– FAA Airworthiness Directive, # 2009-25-13.
– Bombardier Aerospace, Drawing, BAS68028059, Rev. F.
– Bombardier Aerospace, Drawing, BAS68038168, Rev. A.
– Bombardier Aerospace, Drawing, BAS68038169, Rev. A.
– Bombardier Aerospace, Drawing, BAS68038170, Rev. C.
– Bombardier Aerospace, Drawing, BAS68038171, Rev. B.
– Bombardier Aerospace, Restriction and/or Special Instruction (RSI),
C-100-000-25-0015, Rev. --.
– Bombardier Aerospace, Functional Test Engineering Requirements
(FTER), BI100-21445101 Rev. B.
– Bombardier Aerospace Service Bulletin 100-00-02, “Service Bulletin
Description and Policy”.
– BD-100 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 25, 27
and 52.
– BD-100 Supplemental Maintenance Manual (SMM), Chapters 21 and 25.
– Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.

### Page 8

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 6 of 30
– BD-100 Instructions for Continued Airworthiness (ICA), Document Number
BAS68058003-ICA, Rev. B (attached).
– Cox & Co. Field Modification Instructions, D-11338.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
None.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs referenced in the procedures that follow are from the
BD-100 Aircraft Maintenance Manual, unless otherwise specified.
2. All references made to zones, access panels and/or doors, are
from the BD-100 Aircraft Maintenance Manual, Chapter 6.
3. Make sure that all surrounding equipment and furnishings are
properly protected.  Failure to do so may result in damage to
equipment or furnishings.
A. Aircraft Setup
(1) Obey all the electrical/electronic safety precautions.  Refer to
AMM 24-00-00-910-801.
(2) In the flight compartment, open and tag the circuit breaker that follows:
CB PANEL CB NO. NAME ZONE
RCBP D11 ENVIRONMENTAL CARGOHEATER 212
(3) Open the Aft Equipment-Compartment door 182GL.  Refer to
AMM 52-41-00-010-801.
(4) In the aft equipment compartment, open and tag the circuit breakers that
follow:
CB PANEL CB NO. NAME ZONE
RDCPC C6 ENVIRONMENTAL BAGCOMP HTR PWR 1 312
RDCPC C7(see Note) ENVIRONMENTAL BAGCOMP HTR PWR 2 312
Note: Circuit breaker C7 will already be open and tagged on aircraft Post
Alert SB, A100-25-30.
(5) Get access to the baggage compartment from the main cabin.

### Page 9

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 7 of 30
(6) Remove the baggage compartment headliner and keep the attaching
hardware for later installation.  Refer to SMM Chapter 25-53-03.
(7) Remove the L/H baggage compartment panels and keep the attaching
hardware for later installation.  Refer to SMM Chapter 25-53-05.
(8) Remove the insulation blankets in the ceiling area and in the LH sidewall
area as required to have access to the wire harness.
B. Modification – Baggage Bay Sidewall Panel and Heater Mat
For aircraft, Serial No. 20003 to 20123, 20126. 20127, 20129 to 20133, 20135
to 20138, 20140 to 20142, 20144, 20145 and 20147, do the modification to
the sidewall panel applicable to Precision Pattern Incorporated (PPI) interiors.
Refer to drawing BAS68038171.
For aircraft, Serial No. 20124, 20125, 20128, 20134, 20139, 20143, 20146,
20148 to 20284, 20286, 20288 and 20301, do the modification to the sidewall
panel applicable to the Fischer Advanced Composite Components (FACC)
interiors.  Refer to drawing BAS68038170.
(1) Remove the heater mat Part No. 3436-06-1/0 from the LH sidewall panel.
Refer to SMM Chapter 21-42-01.
NOTE: The heater mat may also be referred to as 3436-06-I/O or
3436-06.
(2) For aircraft, Serial No. 20124, 20125, 20128, 20134, 20139, 20143,
20146 and 20148 to 20215, with the heater mat glued to the sidewall
panel, rework the sidewall panel as instructed in Paragraph 2.C. before
you continue to step 2.B.(3).
(3) Discard the attaching hardware when you rework the sidewall panels
installed on the aircrafts identified in Paragraph 2.B. only; otherwise keep
the attaching hardware for later installation.
(4) Install the felt spacers (12) Part No. 253-44020-060 (qty 10) on the LH
sidewall panel as shown in Detail “B” and section E-E, with epoxy
adhesive DP-460, per manufacturer instructions.
(5) Install the felt spacers (12) Part No. 253-44020-060 (qty 6) on the panel
doubler as shown in Detail “B” and section D-D, with epoxy adhesive
DP-460, per manufacturer instructions.
(6) Locate the felt spacers (11) Part No. 253-44020-061 (qty 6) on the LH
sidewall panel attachment points as shown in section C-C.
(7) For aircraft, Serial No. 20003 to 20364, 20366, 20367, 20369 and 20372,
do the modification to the heater mat Part No. 3436-06-1/0 as follows:
Refer to Figure 1.
(a) Disconnect the heater’s two power leads (14 AWG White wires) from
the TM415 pin “D” and pin “E”.

### Page 10

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 8 of 30
(b) Select one of the two 14 AWG leads (White) from the heater mat and
cut it minimum 6 in (15.24 cm) from the clamp on the heater mat
and keep the cut section for later installation.
(c)  Strip 0.38 in (9.65 mm) of the wire insulation from the wire
connected to the heater mat.  Refer to SPM WM 20-11-00-02.
(d) Slide a piece of shrink sleeve approximately 0.75 in (19.05 mm) long
on the wire.
(e) Insert the stripped wire in the crimp barrel of the male half of the fuse
holder and crimp in position with the Sta-Kon manual crimper.
(f) Slide the shrink sleeve over the crimped connection and heat shrink
the sleeve with a heat gun per best shop practice.
(g) Strip 0.380 in (9.65 mm) of the wire insulation from the previously cut
section of wire.
(h) Slide a piece of shrink sleeve approximately 0.75 in (19.05 mm) long
on the wire.
(i) Insert the stripped wire in the crimp barrel of the female half of the
fuse holder and crimp in position with the Sta-Kon manual crimper.
(j) Slide the shrink sleeve over the crimped connection and heat shrink
the sleeve with a heat gun per best shop practice.
(k) Insert the fuse, Part No. MDA-8-R, in one of the fuse holder halves,
assemble the two fuse holder halves together and twist to tighten.
(l) Attach the “FIELD MODIFIED” label Part No. 3436-172, that identifies
the heater mat as Part No. 3436-07 to the lead wire with two cable
ties, Part No. MS3367-4-9.
(m) Use a permanent marker to black out the old Part No. “3436-06-1/0”
on the main surface of the heater mat.
NOTE: Part No. 3436-06-1/0 may also be referred to as
3436-06-I/O or 3436-06.
(n) After completion of the heater mat modification, measure the
resistance across the two lead wires.  The resistance should be
within the following range: 2.12 to 2.59 Ω.
NOTE: The resistance measurement should be performed in a
temperature environment between 12 and 32 °C (55 and
91 °F) with a digital multimeter capable of accurate
resistance measurement below 10 Ω.

### Page 11

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 9 of 30
Figure 1 – Heater Mat Modification/Re-Identification
(8) Connect the heater’s power leads (14 AWG White wires) in TM415 pin
“D” and “E”.
(9) Install the reworked heater mat Part No. 3436-07 on the LH sidewall
panel with the removed attaching hardware.  Refer to
SMM Chapter 21-42-01.
NOTES: 1. For aircraft, Serial No. 20003 to 20123, 20126. 20127, 20129
to 20133, 20135 to 20138, 20140 to 20142, 20144, 20145
and 20147, with PPI sidewall panels, use the new screws,
Part No. MS35206-243, and the new washers, Part No.
NAS1149GN832P.  Refer to drawing BAS68038171.
2. For aircraft, Serial No. 20124, 20125, 20128, 20134, 20139,
20143, 20146, 20148 to 20284, 20286, 20288 and 20301
with FACC sidewall panels, use the new screws, Part No.
MS35206-228, and the new washers, Part No.
NAS1149GN632P.  Refer to drawing BAS68038170.
(10) Rework the baggage heater wiring to have LHS and RHS sidewall heater
mats connected in series to reduce the power as follows:  Refer to
drawing BAS68028059.
(a) Relocate wire FBH4664-14 in TM415, from pin A to pin C as shown
on drawing.  Refer to SPM WM 20-31-00.
(b) Remove and discard ground wire FBH5385N-14 from TM418, pin B.
Refer to SPM WM 20-31-00.

### Page 12

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 10 of 30
(c) Install and connect wire 10BHT3524A-14 from TM415 pin A to
TM418, pin B.  Use existing cables support to attach in position with
cable tie per best shop practice.  Refer to SPM WM 20-16-00-02.
C. Modification – Baggage Bay - LH Sidewall Panel Blind Insert Installation
For aircraft, Serial No. 20124, 20125, 20128, 20134, 20139, 20143, 20146,
and 20148 to 20215.
(1) Before you remove the heater mat, mark the location of the fastener
holes as shown on drawing BAS68038170, sheet 2, detail “B”.
(2) Carefully drill pilot holes of 0.125 in (3.18 mm) diameter through the
heater mat and the first layer only of the sidewall panel.
(3) Carefully remove the heater mat from the sidewall panel.
(4) Open the holes in the heater mat to a diameter of 0.143 to 0.147 in
(3.63 to 3.73 mm).
(5) Use a counter bore to drill the holes, 0.452 to 0.457 in (11.48 to 11.60 mm)
in diameter in the sidewall panel, but do not drill all the way to the other
layer.  Refer to Figure 2.
(6) With an appropriate rotary file, undercut the sandwich panel core to
increase the potting cavity diameter to approximately 1.5 times the
diameter of the insert hole.  Refer to Figure 2.
Insert hole diameter D rotary file
remaining core, adhesive and skin
 maximum 0.062 in (1.57 mm).
undercut hole periphery 1 – 2 cells
(approximately 1.5D)
Figure 2
(7) Make sure to have a minimum clearance of 0.040 in (1.02 mm) between
the tail of the insert and the inside surface of the lower panel skin.
(8) Carefully vacuum the insert holes to remove the dust and any loose
material.
(9) Prepare the inserts, Part No. NAS1836-06-07, for installation as follows:
(a) Clean the insert with solvent.  Refer to SPM 51-25-00-110-801.

### Page 13

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 11 of 30
(b) Stick the self-adhesive installation tab, Part No. NAS 1837, on the
insert head.  Make sure that the holes in the tab are aligned with the
holes in the insert head surface.
NOTE: Handle the cleaned insert/tab assemblies by the tabs to
prevent contamination of the bond surfaces.
(10) Install the blind inserts as follows:
(a) Put the insert in the hole and press down firmly on the tab to make
sure you have full contact between the tab and the panel.  Refer to
Figure 3.
NOTE: Pre-potting is optional, unless otherwise specified.
(b) With an hypodermic syringe, inject the casting resin through one of
the tab fill/vent holes until the cavity is filled and that casting resin
comes out through the opposite fill/vent hole in the tab.  Refer to
Figure 3.
(c) Leave a small excess of casting resin on the tab fill and vent holes
to prevent voids from shrinkage when the casting resin cures.
(d) Cure the casting resin for 168 hours at 25 °C (77 °F) or five hours
at 25 °C (77 °F), then one hour at 65 °C (150 °F).
(e) After the casting resin has completely cured, remove the tab and trim
the casting resin flush with the surface.  Refer to Figure 3.
D. Modification – Baggage Heater Pictogram Installation
For aircraft, Serial No. 20003 to 20259 only:
(1) Install the RH side baggage heater pictogram Part No.
604DX1131000-373-B-L as shown in view A-A of drawing BAS68038168.
Refer to SPM MM 20-80-01-400-801.
(2) Install the LH side baggage heater pictogram Part No.
604DX1131000-373-B-L as shown in view B-B of drawing BAS68038168.
Refer to SPM MM 20-80-01-400-801.
E. Modification – Water Tank Heater Installation
(1) Locate the bracket harness support, Part No. B0816028-001 (qty 1), the
clip harness support, Part No. B0816025-001 (qty 5) and the mounting
base 4 way, Part No. B0816032 (qty 5), as shown in view A-A of drawing
BAS68038169 and bond with acrylic adhesive.  Refer to SPM 51-21-67.
NOTE: It is permissible to install the 4 way mounting base located at
FS643.64 as shown in Figure 4 as an alternate installation, if
there is a duct installed in the lightening hole that does not allow
the routing of the wires as shown in view A-A of drawing
BAS68038169.
(2) Install the heater tube coupling nut HR3BHT, Part No. 325-0296-01,
as shown in Detail “B” of drawing BAS68038169.  Refer to
SPM MM 20-21-00-910-801.

### Page 14

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 12 of 30
(3) Connect and route wire Part No. 10BHT3525B from TM415 pin F to the
heater tube coupling nut HR3BHT as shown on drawing BAS68038169
and drawing BAS68028059.
NOTE: For aircraft with a separate Navigation Interface Unit (NIU)
installed between FS653.00 and FS643.00, route wire
approximately as shown.  If a deviation is required, route wiring
per SPM-WM 20-12-00.
(4) Connect wire 10BHT3526N to ground stud GS3111 with terminal lug
Part No. MS25036-108 and route to the heater tube coupling nut HR3BHT
as shown on drawing BAS68038169 and drawing BAS68028059.
NOTE: For aircraft with a separate Navigation Interface Unit (NIU)
installed between FS653.00 and FS643.00, route wire
approximately as shown.  If a deviation is required, route wiring
per SPM-WM 20-12-00.
(5) Attach wiring to harness support and support structure as shown in view
A-A and detail B of drawing BAS68038169 with tie-wraps per best shop
practice.
(6) Connect wire Part No. 10BHT3525A to the heater HR3BHT with splice
SP1BHT Part No. M81824/1-2.
(7) Install the fuse holder and the fuse, Part No. MDA-5-R, between wire Part
No. 10BHT3525A and wire Part No. 10BHT3525B within 12.0 in. (30.48
cm) of heater tube coupling nut as shown on drawing BAS68028059.
Refer to SPM WM 20-16-00.
(8) Connect wire Part No. 10BHT3526N to the heater HR3BHT with splice
SP2BHT Part No. M81824/1-2 and to GS3111 with terminal lug Part No.
MS25036-108 as shown on drawing BAS68028059.  Refer to
SPM WM 20-31-01-04 and SPM WM 20-16-00.
(9) Apply humiseal on GS3111 as necessary.  Refer to
SPM WM 20-41-00-02.
F. Testing
(1) In the aft equipment compartment, remove the tags and close the circuit
breakers that follow:
CB PANEL CB NO. NAME ZONE
RDCPC C6 ENVIRONMENTAL BAGCOMP HTR PWR 1 312
RDCPC C7 ENVIRONMENTAL BAGCOMP HTR PWR 2 312

### Page 15

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 13 of 30
(2) In the flight compartment, remove the tag and close the circuit breaker that
follows:
CB PANEL CB NO. NAME ZONE
RCBP D11 ENVIRONMENTAL CARGOHEATER 212
(3) Do the functional test of the heater tube coupling nut located under the water
tank and the sidewall heater mat as follows:
NO. STEP EXPECTED RESULT
1
Perform CARGO
COMPARTMENT HEATERS
TEST, in the MDC
(Maintenance Data
Computer).
NOTE: Cargo compartment
heaters test is accessible on
IASC 1A in the LRU test.
· After several seconds, Heater
Command annunciates ON.
· Use a clamp on ammeter to
verify that at terminal TM415
location on wire 10BHT3525B-
14 the heater tube coupling
nut current is between 0.09A
(min) and 0.12A (max).
· Verify that the heater tube
coupling nut, is warm to the
touch.
NOTE: The baggage heaters will be turned off after five minutes of
continuous operation.  Also the baggage heater thermostats open at
125° F (37° C) and close at 80° F (26° C). High ambient
temperature may require the baggage compartment to be
cooled prior to test.
2
Select TURN OFF CARGO
COMPARTMENT HEATERS
TEST in the MDC.
· After several seconds, Heater
Command annunciates OFF.
· Use a clamp on ammeter to
verify that at terminal TM415
location on wire 10BHT3525B-
14 the heater tube coupling
nut current is zero ampere.
3
Perform again the CARGO
COMPARTMENT HEATERS
TEST, in the MDC.
· After several seconds, Heater
Command annunciates ON.
· At TM 415, use a clamp on
ammeter around the heater
mat lead to verify that the
current is between 4.6A (min)
and 6.8A (max).

### Page 16

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 14 of 30
NO. STEP EXPECTED RESULT
4
On the RCBP, open and tag
Circuit Breaker D11, to
remove electrical power
· When power is removed, after
several seconds Heater
Command annunciates OFF.
· Verify that mat heaters current
is zero.
5 Remove the tag and close circuit breaker D11 in RCBP.
NOTE:  On the ground and in flight with an aircraft altitude less than 20,000
feet (6096 m), the Cargo Heat Control Relay is not commanded and
no power is provided to the baggage heaters. Above 20,000 feet
(6096 m) IACS 1 Channel A energizes the relay and the cargo
compartment heating system is then turned ON.
(4) Install the removed LH baggage compartment panels with the removed
attaching hardware.  Refer to SMM Chapter 25-53-05.
(5) Do the operational test of the baggage compartment heat system.  Refer
to BAS68058003-ICA, SMM Chapter 21-42-50.
(6) Insert BAS68058003-ICA into the existing aircraft Specific Maintenance
Manual (SMM) in chapter 21-42.
G. Close-out
(1) Install the baggage compartment headliner panel with the removed
attaching hardware.  Refer to SMM Chapter 25-53-03.
(2) Make sure there are no loose materials, insulation and/or any FOD that
may obstruct the safety valve sensing port, before you install the
headliner panel.  Use insulation tape to attach any loose insulation
blankets if necessary.  Refer to SPM MM 51-28-01-350-801.
(3) Remove all tools, equipment and unwanted materials from the aircraft.
(4) Close the Aft Equipment-Compartment door 182GL.  Refer to
AMM 52-41-00-410-801.
H. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and
send the attached Incorporation Notice to Bombardier Business Aircraft
Customer Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback.  Please take a moment to fill out our easy on-line
Service Bulletin survey:
http://csefeedback.aero.bombardier.com

### Page 17

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 15 of 30
3. MATERIAL INFORMATION
A. Kit
Kit 100K25-35 is necessary to do this Service Bulletin on aircraft, Serial No.
20003 to 20284, 20286, 20288 and 20301 and contains the parts that follow:
NEW
PART NO.
QTY ITEM USED
PART NO.
INSTRUCTIONS -
DISPOSITION
253-44020-060 16 Felt Spacer - -
253-44020-061 6 Felt Spacer - -
MS35206-228 7 Screw - -
MS35206-243 7 Screw - -
NAS1149GN632P 7 Washer - -
NAS1149GN832P 7 Washer - -
NOTE: This kit contains screws and washers for both type of sidewall panels, PPI
and FACC, use the ones applicable to your aircraft’s configuration.
Kit 100K25-35A is necessary to do this Service Bulletin on aircraft, Serial No.
20003 to 20259 and contains the part that follows:
NEW
PART NO.
QTY ITEM USED
PART
NO.
INSTRUCTIONS -
DISPOSITION
604DX1131000-
373-B-L
2 Pictogram/
Baggage Heater
- -
Kit 100K25-35B is necessary to do this Service Bulletin on aircraft, Serial No.
20003 to 20364, 20366, 20367, 20369 and 20372 and contains the parts that
follow:
NEW
PART NO.
QTY ITEM USED
PART NO.
INSTRUCTIONS -
DISPOSITION
325-0296-01
(1005355949-001)
1 Heater, Tube
coupling Nut
- -
3436-172 1 Cox & Co., Label - -
ALBCBS-310-59-1
(B0816028-001)
1 Bracket Harness
Support
- -
ALBCBS-304-59-01
(B0816025-001)
5 Clip Harness
Support
- -
ABM1M-AT
(B0816032)
5 Base, Mounting 4
Way
- -

### Page 18

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 16 of 30
NEW
PART NO.
QTY ITEM USED
PART NO.
INSTRUCTIONS -
DISPOSITION
B0816019-001 30 Strap, Tie Down - -
BAS68028059/01 1 Wire Kit - -
HFA-R 2 Fuse Holder - -
MDA-5-R 1 Fuse - -
MDA-8-R 1 Fuse - -
M23053/5-106
(or equivalent)
2 Shrink, Sleeve - -
MS3367-4-9
(or equivalent)
2 Cable, Tie - -
NOTES: 1. In case of discrepancy between these lists and the “Service Bulletin Kit
Parts List” contained in the respective kit, then the latter list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
The part that follows may be necessary to do this Service Bulletin and is available
from Bombardier Aerospace Parts Services, Montreal:
NEW
PART NO.
QTY ITEM USED
PART NO.
INSTRUCTIONS -
DISPOSITION
NAS1836-06-07 6 Blind Insert - -
NOTE: The part number for the item listed above is subject to change without
revision to this Service Bulletin.  In case of discrepancy between this
list and any other list, the Illustrated Parts Catalog prevails and shall
be used to determine the latest part number.

### Page 19

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 17 of 30
C. Material
The materials that follow, or equivalent, are necessary to do this Service Bulletin.
These can be purchased from a local supplier.  Bombardier Aerospace does not
pay for these consumables.
DESCRIPTION PART
No./NAME
SPECIFICATION QUANTITY SUPPLIER
(See Note)
Acrylic
Adhesive
Lord 201 / 19 - As
Necessary
Code: A
Epoxy
Adhesive
Scotch Weld
DP460
- As
Necessary
Code: B
Tape,
Insulation
OT-57CW MMS-01-001
Type 1.
As
Necessary
Code: C
Epoxy
Adhesive
ATR 525 A/B BAMS532-002
Type II
As
Necessary
Code: D
Alcohol,
Isopropyl
- TT-I-735 As
Necessary
Code: E
Paper,
Abrasive
- 180-Grit As
Necessary
Code: E
NOTES: 1. Refer to the table that follows for each supplier’s address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material
is indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate.  In the event that this
information has changed, the operator is encouraged to use the
World Wide Web to find a local supplier.

### Page 20

MODEL BD-100-1A10 (CH-300)
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 18 of 30
SUPPLIERS ADDRESSES BY CODES
Code: A
Lord Corporation
World Headquarters
111 Lord Drive
Cary, NC 27511-7923
U.S.A.
Tel.: 1 877 275 5673
www.lord.com
Code: B
3M
Center BLDG 251-3
St-Paul, MN, 55144-1000
U.S.A.
Tel: 1-888-364-3577
www.3m.com
Code: C
Orcon Corporation
1570 Atlantic Street
Union City, California 94587-2040
USA
Tel: 510-489-8100
www.orcon-aerospace.com
Code: D
AAR Composites Inc.
14201 Myerlake Circ.
Clearwater FL, 33760
USA
Tel: 916-566-6014
www.aarcorp.com
Code: E
Commercially Available
D. Publications
The publication that follows is required after this Service Bulletin has been
incorporated.
– Instruction for Continued Airworthiness (ICA), Water Tank Connection
Heater and Baggage Compartment Heater Modification, Document Number
BAS68058003 - ICA.  Refer to Paragraph 1.K.

### Page 21 (OCR)

MODEL BD-100-1A10 (CH-300)
(a) Without Pre-potting  (b) With Pre-potting
Tab
Pre-potting of 1/3"
of the cavity
Insert installed
onto panci
Adhesive extruded
out in vent hole
Excess of adhesive
in vent hole
Adhesive trimmed
flush after curing
Figure 3 - Blind Insert Potting Installation
Basic Issue: Nov 15/2012  100-25-35
Revision 02: Jan 11/2016  Page 19 of 30

### Page 22

MODEL BD-100-1A10 (CH-300)
Figure 4 – Alternate Installation
Basic Issue: Nov 15/2012 100-25-35Revision 02: Jan 11/2016 Page 20 of 30
CSB2553_001
exclusive property of Bombardier Inc. and
their copy or reproduction by any third party
is strictly forbidden.
Drawings and data contained herein are the
A A
A-A
ALTERNATE
INSTALLATION

### Page 23

BAS68038168 – Baggage Heater – Placards – Installation
(Sheet 1 of 2, Rev. A)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 21 of 30

### Page 24

BAS68038168 – Baggage Heater – Placards – Installation
(Sheet 2 of 2, Rev. A)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 22 of 30

### Page 25

BAS68038169 – Water Tank – Heater Installation
(Sheet 1 of 2, Rev. A)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 23 of 30

### Page 26

BAS68038169 – Water Tank – Heater Installation
(Sheet 2 of 2, Rev. A)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 24 of 30

### Page 27

BAS68038170 – LH Sidewall Panel – Modification
(Sheet 1 of 2, Rev. C)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 25 of 30

### Page 28

BAS68038170 – LH Sidewall Panel – Modification
(Sheet 2 of 2, Rev. C)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 26 of 30

### Page 29

BAS68038171 – LH Sidewall Panel – Modification
(Sheet 1 of 2, Rev. B)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 27 of 30

### Page 30

BAS68038171 – LH Sidewall Panel – Modification
(Sheet 2 of 2, Rev. B)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 28 of 30

### Page 31

BAS68028059 – WD – Baggage Heat Wiring Modification
(Sheet 1 of 2, Rev. F)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 29 of 30

### Page 32

BAS68028059 – WD – Baggage Heat Wiring Modification
(Sheet 2 of 2, Rev. F)
Basic Issue: Nov 15/2012
Revision 02: Jan 11/2016
100-25-35Page 30 of 30

### Page 33

SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: 100-25-35 ISSUE: Rev. 02 DATED: Jan 11/2016
TITLE: Modification – Baggage Compartment – Modification to the LH & RH Baggage Bay
Heater Installations and Reactivation of the LH Baggage Bay Heater After Modification
and Re-identification as Part No. 3436-07
In an effort to improve the quality of our technical communications, we are replacing
the standard Service Bulletin Evaluation Form with an on-line Service Bulletin
Survey and we are requesting your feedback.  Please take a moment to fill out our
easy on-line Service Bulletin survey:
http://csefeedback.aero.bombardier.com

### Page 34

SERVICE BULLETIN INCORPORATION SHEET – “100-25-35”
BOMBARDIER
SUBMISSION Upon completion of the Service Bulletin, please fill-in, fax to
(514) 855-8798 or e-mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
     COMPLIED WITH
Service Bulletin
Number
 Rev. * Parts
Completed
 YES NO N/A Remarks/Reason
100-25-35  02 -
- - -
- - -
Actual hours to accomplish Service Bulletin:
* NOTES: 1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B,
C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be reported
unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should be
reported.
Aircraft Serial No.  Aircraft Reg. No.
Airframe Hours:  Airframe Landings
S.B. Incorporation date  Service Order No.
(dd/mm/yy)
Facility Incorporating S.B.
Name Signature Date
                          (dd/mm/yy)Signature not required if sent by E-Mail

### Page 35

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Bombardier Business Aircraft Customer Services (BBACS)
P.O. Box 6087, Station Centre-ville
Montreal, Québec, Canada H3C 3G9
Attention: Customer Support Department, Maintenance Engineering
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
