# Bombardier Service Bulletin 100-27-16

Copy: No revision named ("U.S. DOT/FAA - SB 100-27-16 Basic"), 12 pages: PDF https://openairdocs.org/files/sha256/7d/8c/7d8cfce222a37ffc9bacdf8fb55767df24d30f09d5df955b5816a1f95d917201; text https://openairdocs.org/service-documents/bombardier/sb-100-27-16/file/7d8cfce222a3.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-0088; AD 2015-15-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-27-16
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-27-16

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2015-15-08](https://openairdocs.org/ad/2015-15-08.md), effective Aug 28, 2015: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-27-16/proposed.md).

## Text (12 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2015-0088; AD 2015-15-08 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Basic Issue: Oct 31/2013 100-27-16 
  Page 1 of 1 
SERVICE BULLETIN SUMMARY 
This Service Bulletin is available at: 
www.cic.bombardier.com  
MODEL BD-100-1A10 (CL-300) 
ATA 27-61 
FLIGHT CONTROLS 
SPECIAL CHECK/MODIFICATION – CONTROL AND INDICATION SYSTEM – 
SOFTWARE CHANGE TO IMPROVE SPOILER ELECTRONIC CONTROL UNIT 
(SECU) RELIABILITY AND TO ELIMINATE A NON-COMPLIANCE IN THE ROLL 
DISCONNECT LOGIC 
The information below is provided for your reference.  For full details, please 
see corresponding paragraph contained within this bulletin. 
RECOMMENDED
SPECIFIED TIME COMPLIANCE 
COMPLIANCE TIME 
Before 31 Oct 2018 
 
EFFECTIVITY: A/C Serial No. 20003 to 20407 
MANPOWER: 4 man-hours are necessary to upgrade one SECU. 
6 man-hours are necessary to upgrade two SECUs. 
CONTINUED AIRWORTHINESS (CAW)  
FLEET CAMPAIGN 
YES  NO  
KITS and/or PARTS YES  NO  
TOOLING/GSE YES  NO  
PLANNING INFORMATION:  See important 
information at the start of Paragraph 1. YES  NO  
DEDICATED SCHEDULE YES  NO  
PREREQUISITE SERVICE BULLETINS: SB 100-27-09 is a prerequisite and must be 
done before or at the same time as this Service Bulletin. 
NOTE: This Service Bulletin is expected to become the subject of an Airworthiness 
Directive which will make it necessary to implement this Service Bulletin. 
To place an order for parts or kits, please call Bombardier Aerospace Parts Services at: 
514-855-2999 or 1-866-538-1247

### Page 2

Refer to applicable governmental agency regulations and requirements and make sure that the work described in this 
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards. 
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or 
by any means without the prior written consent of Bombardier Inc. and/or its affiliates. 
© 2013 Bombardier Inc.  All rights reserved 
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries. 
Basic Issue: Oct 31/2013 100-27-16 
  Page 1 of 8 
SERVICE BULLETIN 
This Service Bulletin is available at: 
www.cic.bombardier.com  
MODEL BD-100-1A10 (CL-300) 
ATA 27-61 
FLIGHT CONTROLS 
SPECIAL CHECK/MODIFICATION – CONTROL AND INDICATION SYSTEM – 
SOFTWARE CHANGE TO IMPROVE SPOILER ELECTRONIC CONTROL UNIT 
(SECU) RELIABILITY AND TO ELIMINATE A NON-COMPLIANCE IN THE ROLL 
DISCONNECT LOGIC 
1. PLANNING INFORMATION  
NOTE: This Service Bulletin also includes In structions for SECUs in the operator’s 
stockroom. 
A. Effectivity 
BD-100-1A10 aircraft, Serial No. 20003 to 20407. 
All other subsequent BD-100-1A10 aircraft are scheduled for the modification  
in production (Ref.:  Modification Summary 100T010596). 
NOTE: The instructions given in this Service Bulletin are only applicable to  
the systems and parts installed at the time of delivery of the aircraft  
or as changed by Bombardier Aerospace Service Bulletin(s).  
Before you do this bulletin, examine all STC, STA or equivalent  
action changes to make sure that this bulletin can be completed.

### Page 3

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 2 of 8 
B. Reason 
As the throttle lever is moved slowly from “AT IDLE” position, the throttle quadrant 
assembly (TQA) switch will pass through an indeterminate state. If the duration of 
the indeterminate state is more than the Spoiler Systems monitor threshold, a 
cyan “SPOILERS FAULT” or an amber “SPOILERS FAIL” Engine Indication and 
Crew Alerting System (EICAS)” message will be posted by the Spoiler System.  
The SECU software has been improved to disable TQA switch monitoring when 
the Throttle Lever is in the range of the switch’s intermediate state. 
Also, an extremely unlikely timing difference between Command and Monitor 
channels, coupled with an intermittently failed Roll Disconnect Switch, could 
cause the complete loss of spoiler functionality. 
This Service Bulletin introduces a modification to the SECU software to correct 
this timing error and prevent the loss of both SECUs under these conditions thus 
maintaining spoiler functionality. 
C. Description 
This Service Bulletin gives instructions to: 
– Get access to the SECU, 
– Verify the SECU Part Number, 
– Remove the SECU if necessary, 
– Upgrade the SECU software if necessary, 
– Reidentify the upgraded SECU if necessary, 
– Install the upgraded SECU if necessary, and 
– Do the necessary tests to make sure that the system operates correctly. 
D. Compliance 
Recommended to be incorporated before 31 Oct 2018. 
E. Approval 
The technical content of this Service Bulletin has been approved under  
the authority of Transport Canada Civil Aviation (TCCA) Design Approval 
Organization (DAO) No. DAO #93-Q-02. 
NOTES: 1. The technical content of this Service Bulletin is accepted by the  
FAA under the Canada/USA bilateral Aviation Safety Agreement. 
2. The technical content of this Service Bulletin is accepted by EASA  
in accordance with established procedures.

### Page 4

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 3 of 8 
F. Manpower 
NOTES: 1. The man-hours given are estimates to help you schedule the tasks  
given in this bulletin.  The estimates are for direct labor performed by  
an experienced crew and do not include the time for familiarization, 
planning, aircraft preparation in hangar such as towing and 
positioning of scaffolds, removal of interior furnishings, repainting, 
supervision and inspection.  
For more information related to the manpower estimates, refer to  
SB 100-00-02. 
2. This Service Bulletin may require consumable materials that have 
specific curing times (refer to Paragraph 3).  The accumulated curing 
time is not included in the labor estimates and should be considered 
for planning purposes before you schedule this Service Bulletin. 
4 man-hours are necessary to upgrade one SECU. 
6 man-hours are necessary to upgrade two SECUs. 
The labor required to do this Service Bulletin is at no cost if:  
(i) the work is done during new aircraft warranty period, and  
(ii) the work is done at Bombardier  Business Aviation Services (BBAS) 
or Authorized Service Facilities (ASF), and 
(iii) this Service Bulletin is scheduled within the compliance time. 
G. Material - Cost and Availability 
No kit is necessary to do this modification.  For the parts necessary to do this 
modification on SECU Part No. C47330-006, C47330-007 or C47330-008,  
refer to Paragraph 3.B. 
These parts are available at no cost if  a no-charge purchase order is sent to 
Bombardier Aerospace within the compliance time. 
For SECUs, Part No, C47330-006, C47330-007 and C47330-008 in the operator’s 
stock room, send units for upgrade by Moog, to Bombardier Aerospace at one of 
the two addresses given below: 
Learjet – Core Returns 
8219 West Irving, Bldg 9, Dock 9, 
Wichita, KS 67209 
USA 
or 
Distribution Centre Frankfurt – Core Returns 
Bombardier Aerospace Germany GmbH 
Hans-Boeckler-Strasse 9 
GROSS-GERAU Hesse 64521 
Germany

### Page 5

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 4 of 8 
Refer to your Material Return Authorization (MRA) form to find the applicable 
return address. 
During or after the above free period, Smart Parts Plus does not pay for the parts 
required to complete this software change. 
H. Tooling 
The equipment and tools listed below are necessary to do this modification: 
GSE REFERENCE NO. PART NO. DESCRIPTION 
20X-00-04 M1-G-KIT or 
equivalent 
Portable Bonding Tester 
24-00-24 S4933959-501 Tag, Circuit Breaker 
- CB59838-001 Wire Harness (Note 3) 
- CB60286-001 Software, CDROM (Note 3) 
Commercially Available - Laptop with Windows XP or 
Windows 7 operating system, 
an RS-232 Serial or USB 2.0 
Port, a USB-to-Serial adapter 
cable and a CD drive. 
Commercially Available - Power Supply (28Vdc and 2A) 
NOTES: 1. Refer to the BD-100 Illustrat ed Tool and Equipment Manual (ITEM)  
to make sure that you use the correct equipment configuration. 
2. Refer to the Liability Statement in the ITEM for acceptable GSE  
equivalents. 
3. The wire harness and CDROM necessary to complete this Service 
Bulletin will be available at each BAS and from Bombardier Aerospace 
Parts Services for rental. 
I. Weight and Balance 
No change. 
J. Electrical Load Data 
No change.

### Page 6

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 5 of 8 
K. References 
– Bombardier Aerospace, Modification Summary, 100T010596, Rev. C. 
– Bombardier Aerospace, Modification Summary, BB100T010721, Rev. A. 
– Bombardier Aerospace, Restriction and/or Special Instruction (RSI),  
C-100-000-27-0300, Rev. --1. 
– Bombardier Aerospace, Kit Drawing K1000070295, Rev. --. 
– Bombardier Aerospace, Standard Pr actices Manual (SPM), Chapter 51. 
– Bombardier Aerospace, SB 100-00-02 “Ser vice Bulletin Description and Policy”. 
– Bombardier Aerospace, SB 100-27-09, Re v. 02 “Modification – Multi-Function 
Spoiler – Introduction of the Spoiler Electronic Control Unit (SECU) Part No. 
C47330-006 or C47330-007”. 
– BD-100 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 27 and 51. 
– BD-100 Aircraft Illustrated Part s Catalog (AIPC), Chapter 27. 
– Moog, Service Bulletin C47330-27-02, Rev. 1 “Flight Controls: Spoiler 
Electronic Control Unit (SECU) Software Upgrade” (attached). 
– Moog, Service Bulletin C47330-27-03, Rev. 1 “Flight Controls: Spoiler 
Electronic Control Unit (SECU) Software Upgrade” (attached). 
– Moog, Service Bulletin C47330-27-04, Rev. 1 “Flight Controls: Spoiler 
Electronic Control Unit (SECU) Software Upgrade” (attached). 
L. Other Publications Affected 
BD-100 Aircraft Illustrated Parts Catalog (AIPC), Chapter 27. 
M. Equivalent Service Bulletins 
None.

### Page 7

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 6 of 8 
2. ACCOMPLISHMENT INSTRUCTIONS 
NOTES: 1. All TASKs given in the procedur es that follow are from the BD-100 
Aircraft Maintenance Manual unless otherwise specified. 
2. All references made to zones, access panels and/or doors, are from  
the BD-100 Aircraft Maintenance Manual, Chapter 6. 
A. Aircraft Setup 
(1) Obey all electrical/electronic safety precautions.  Refer to  
TASK 24-00-00-910-801. 
(2) Obey all electrostatic safety pr ecautions.  Refer to TASK 24-00-00-910-802. 
B. PART A – Inspection of SECU A118 and SECU A119 
Verify the part number of SECU A118 and SECU A119. 
NOTES: 1. The SECU A118 and SECU A119 are located in the right equipment 
rack.  Refer to TASK 27-61-00-992-801. 
 2. For SECU Part No. C47330-006, C47330-007 or C47330-008 in the 
operator’s stock room, refer to Paragraph 1.G. for disposition. 
(a) For aircraft with SECU Part No. C47330-006, C47330-007 or  
C47330-008, continue with PART B of this Service Bulletin. 
(b) For aircraft with SECU Part No. C47330-009, C47330-010 or  
C47330-011, continue with Close-out. 
C. PART B – Modification of SECU, Part No. C47330-006, C47330-007 or  
C47330-008 
CAUTION: OBEY ALL ELECTROSTATIC DISCHARGE SAFETY PRECAUTIONS 
WHEN YOU DO MAINTENANCE ON ELECTROSTATIC DISCHARGE 
SENSITIVE (ESDS) COMPONENTS.  STATIC VOLTAGE CAN CAUSE 
DAMAGE TO ESDS COMPONENTS. 
(1) Remove SECU A118 and/or SECU A119 as necessary.  Refer to  
TASK 27-61-05-000-801. 
(2) Incorporate the applicable Moog Service Bulletin as follows: 
SECU Part No. Moog Service Bulletin. 
C47330-006 C47330-27-02 
C47330-007 C47330-27-03 
C47330-008 C47330-27-04 
(3) Re-identify the upgraded SECU per t he related Moog Service Bulletin. 
(4) Install the upgraded SECU A118 and/or SECU A119 as necessary.  Refer to  
TASK 27-61-05-400-801.

### Page 8

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 7 of 8 
(5) Do the electrical bonding of the SECU A118 and/or SECU A119.  Refer to 
SPM TASK 51-80-00-760-801. 
NOTE: The maximum allowable resistance is 5 milliohms between the 
avionics rack and the bare screws at the bottom of the front face  
of the SECU. 
D. Testing 
(1) Do the electronic rigging of the SECU A118 and/or SECU A119 as necessary.  
Refer to TASK 27-61-05-820-802. 
(2) Do the operational test of the spoiler system.  Refer to  
TASK 27-61-00-710-801. 
E. Close-out 
Remove all tools, equipment and unwanted materials from the aircraft. 
F. Recording 
When this Service Bulletin is completed, make an entry in the aircraft log and 
send the attached Incorporation Notice to Bombardier Business Aircraft Customer 
Services (BBACS). 
In an effort to improve the quality of our technical communications, we are 
requesting your feedback.  Please take a moment to fill out our easy on-line 
Service Bulletin survey: 
http://csefeedback.aero.bombardier.com 
3.  MATERIAL INFORMATION 
A. Kit 
No kits required. 
B. Parts 
The parts that follow are necessary to do this Service Bulletin and are available  
from Bombardier Aerospace Parts Services, Montreal. 
NEW  
PART NO. 
QTY ITEM USED 
PART NO. 
INSTRUCTIONS - 
DISPOSITION 
CB68209-001 
or 
CB68210-001 
or 
CB68211-001 
2 Label (Note 1) 
 
Label (Note 2) 
 
Label (Note 3) 
- - 
NOTES: 1. For SECU, Part No, C47330-006, upgraded to Part No. C47330-006A. 
2. For SECU, Part No, C47330-007, upgraded to Part No. C47330-007A. 
3. For SECU, Part No, C47330-008, upgraded to Part No. C47330-008A.

### Page 9

MODEL BD-100-1A10 (CL-300) 
Basic Issue: Oct 31/2013 100-27-16 
  Page 8 of 8 
C. Material 
The materials that follow are necessary to do this Service Bulletin.  These can be 
purchased from a local supplier.  Bombardier Aerospace does not pay for these 
consumables. 
DESCRIPTION PART 
No./NAME 
SPECIFICATION QUANTITY SUPPLIER
(See Note)
Isopropyl 
Alcohol 
- TT-I-735  As 
Necessary 
Code: A 
Sealant 
CT: 5 hours 
 
 
or 
Clear Coat 
- MIL-V-173C 
or 
A38662-20 
or equivalent 
As 
Necessary 
Code: A 
NOTES: 1. Refer to the table that follows for the supplier’s address listed by 
code. 
2. At time of release of this Service Bulletin, the information on the 
supplier was valid and accurate.  In the event that this information 
has changed, the operator is encouraged to use the World Wide Web 
to find a local supplier. 
SUPPLIERS ADDRESSES BY CODES 
Code: A 
Commercially Available 
D. Publications 
No publications required.

### Page 10

SERVICE BULLETIN EVALUATION FORM 
(Your ideas will help us provide better bulletins) 
SERVICE BULLETIN: 100-27-16 ISSUE: Basic DATED: Oct 31/2013 
      
TITLE: Special Check/Modification – Control and Indication System – Software Change to 
Improve Spoiler Electronic Control Unit (SECU) Reliability and to Eliminate a  
Non-Compliance in the Roll Disconnect Logic 
 
 
 
 
 
 
 
In an effort to improve the quality of our technical communications, we are replacing 
the standard Service Bulletin Evaluation Form with an on-line Service Bulletin 
Survey and we are requesting your feedback.  Please take a moment to fill out our 
easy on-line Service Bulletin survey:   
 
 
 
 
 
http://csefeedback.aero.bombardier.com

### Page 11

SERVICE BULLETIN INCORPORATION SHEET – “100-27-16” 
 
BOMBARDIER 
SUBMISSION Upon completion of the Service Bulletin, please fill-in, fax to 
(514) 855-8798 or e-mail to Fracas at fracas.montreal@aero.bombardier.com 
 
If your aircraft is registered on CAMP and you are reporting to them, 
please do not send the incorporation sheet to Bombardier. If your aircraft 
is on another tracking system, please contact Bombardier to make 
arrangements for automated data submission. 
 
 
           COMPLIED WITH  
 Service Bulletin 
Number 
 Rev.  * Parts 
Completed 
YES NO N/A Remarks/Reason 
 100-27-16  Basic  PART A     
 “  “  PART B     
 -  -  -     
 
 Actual hours to accomplish Service Bulletin:    
 
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A, B, 
C, D, etc.) which can be carried out separately, indicate only those parts 
completed at this time. 
2. For repetitive checks (usually PART A) only the initial check should be reported 
unless otherwise stated in the Service Bulletin. 
* NOTES:  
 
 
  
  3. When more than one part is carried out at the same time, each part should be 
reported. 
 
 Aircraft Serial No.   Aircraft Reg. No.   
 Airframe Hours:   Airframe Landings   
 S.B. Incorporation date   Service Order No.   
  (dd/mm/yy)    
 Facility Incorporating S.B.  
 Name  Signature  Date  
                               (dd/mm/yy) Signature not required if sent by E-Mail

### Page 12

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --  
 
 
 
 
 
Bombardier Business Aircraft Customer Services (BBACS) 
P.O. Box 6087, Station Centre-ville 
Montreal, Québec, Canada H3C 3G9 
 
Attention: Customer Support Department, Maintenance Engineering 
 
 
 
 
 
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
