# Bombardier Service Bulletin 100-27-20

Copy: Revision 01 ("SB100-27-20R1"), 18 pages: PDF https://openairdocs.org/files/sha256/b5/a5/b5a52873526dfd061ce7b1f8e3618b88c6d7c1fc55e4b9b52249624a03ca854b; text https://openairdocs.org/service-documents/bombardier/sb-100-27-20/file/b5a52873526d.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2023-0439; AD 2023-11-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-27-20
- Latest revision known: 100-27-20, Revision 01, dated December 1, 2020 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-27-20

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2023-11-04](https://openairdocs.org/ad/2023-11-04.md), effective Jul 21, 2023: Revision 01

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-27-20/proposed.md).

## Text (18 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2023-0439; AD 2023-11-04 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

Discard the Basic Issue of this Service Bulletin dated Nov 09/2020, and replace in its
entirety with this Revision 01.
Service Bulletin No. 100−27−20
Date of Basic Issue Nov 09/2020
Revision No. 01 Dated Dec 01/2020
This revision has no effect for aircraft on which the Basic Issue, of this Service
Bulletin was done thus no other action is necessary. Do not sign the log book if you
have not done this revision. Keep the previous log book entry. You may make an
entry as "Not Applicable" for this revision.
This revision is issued to:
1. Add, in Paragraph 1. Planning Information, a new NOTE (5) that this Service Bulletin
intent can be checked by verification of the airplane maintenance records.
2. Add, in Paragraph 2. Accomplishment Instruction NOTES, a new NOTE (4), on detail
verification instructions.
SERVICE BULLETIN
MODEL BD−100−1A10 (CH−300)
100−27−20
Page 1 of 1
REVISION TRANSMITTAL SHEET

### Page 2

SPECIAL CHECK/MODIFICATION – HORIZONTAL STABILIZER –
NO-BACK ASSEMBLY PAWL INSPECTION
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Within 5 years from this Service Bulletin
release date (Basic Issue)
EFFECTIVITY: A/C Serial No. 20003 to 20457
MANPOWER: Refer to Paragraph 1.F
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN YES NO
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive (AD) which will
make it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 27−40
FLIGHT CONTROLS
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 1 of 1
This Service Bulletin is available at:

### Page 3

SPECIAL CHECK/MODIFICATION – HORIZONTAL STABILIZER –
NO-BACK ASSEMBLY PAWL INSPECTION
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. Please contact your
Regional Manager (RM), Field Service Representative (FSR) or Customer
Service Representative (CSR) to schedule your aircraft as there is a
limited availability. The parts will be allocated on a first come first serve
basis. For more information on dedicated schedules, refer to
SB 100−00−002.
3. If the Horizontal Stabilizer Trim Actuator (HSTA) is removed, then the
personnel necessary is as follows:
− two persons for the removal and installation of the HSTA;
− two persons for the rigging check of the pitch trim system; and
− two persons for the operational test of the pitch trim system.
4. This Service Bulletin is also applicable for the HSTA’s in the operator’s
stock room.
5. In certain cases, the intent of this Service Bulletin can be satisfied through
a verification of the airplane maintenance records. Refer to Paragraph 2.A.
"ACCOMPLISHMENT INSTRUCTIONS" for more details.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 27−40
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2020 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 1 of 14
This Service Bulletin is available at:

### Page 4

A. Effectivity
BD−100−1A10 aircraft, Serial No. 20003 to 20457 with the HSTA Serial Numbers
listed in the table below:
TABLE 1 - HSTA SERIAL NUMBERS
PART NO. NOMENCLATURE SERIAL NUMBERS
C47100−003
C47100−004
HORIZONTAL
STABILIZER TRIM
ACTUATOR
0001, 0002A, 0003−0096, 0097A,
0098−0146, 0147A, 0148−0167, 0168A,
0169−0236, 0237A, 0238−0241, 0242A,
0243−0302, 0304−0324, 0326−0336,
0337A, 0338−0349, 0350A, 0351−0528,
0529A, 0530−0571, 0572A, 0573−0636,
0637A, 0638−0659, 0660A, 0661−0808,
0809, 0810, 0812−0817, 0818, 0819,
0820, 0821−0854, 0855A, and
0856−0886.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
Condition:
The horizontal stabilizer trim system has three means to prevent un−commanded
HSTA motion; the No−Back mechanism and the two motor brakes. Any of these
three devices will prevent uncommanded motion of the Horizontal Stabilizer
(HSTAB). The No−Back is a mechanical brake device located inside the HSTA.
The No−Back mechanism uses two tension pawls and two compression pawls to
prevent movement of the horizontal stabilizer control surface caused by external
loads during flight. It is possible that one of these pawls may have been installed
upside−down (inverted 180 Degree). Therefore, a one−time inspection of the
no−back assembly is necessary and if the installation is found not acceptable, the
HSTA will be replaced.
C. Description
This Service Bulletin gives instructions in PART A to:
− Get access to the HSTA and identify the serial numbers to make sure this
Service Bulletin is applicable to your aircraft.
This Service Bulletin gives instructions in PART B to:
− If applicable, Inspect and identify the HSTA in accordance with the Moog
VSB C47100−27−02.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 2 of 14

### Page 5

This Service Bulletin gives instructions in PART C to:
− If applicable, identify the HSTA in accordance with the Moog
VSB C47100−27−03.
This Service Bulletin gives instructions in PART D to:
− If applicable, replace the HSTA.
− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended within 5 years from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 100−00−02.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
2 man−hours are necessary to do PART A of this Service Bulletin.
NOTE: 0.5 man−hours is necessary to do PART A of this Service Bulletin if the
HSTA is not installed in an aircraft (example: HSTA in the stock room).
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 3 of 14

### Page 6

6 man−hours are necessary to do PART B of this Service Bulletin.
NOTE: 3 man−hours is necessary to do PART B of this Service Bulletin (Ref: VSB
C47100−27−02, On−bench instructions) if the HSTA is not installed in an
aircraft (example: HSTA in the stock room).
1 man−hour is necessary to do PART C of this Service Bulletin.
NOTE: 1 man−hours is necessary to do PART C of this Service Bulletin if the
HSTA is not installed in an aircraft (example: HSTA in the stock room).
16 man−hours are necessary to do PART D of this Service Bulletin.
1.5 man−hours are necessary to do Testing of this Service Bulletin.
The labor required to do PART A and PART B of this Service Bulletin is at no
cost if:
− the work is done during new aircraft warranty period,
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 60 months from its release date
(Basic Issue).
The labor required to do PART C and PART D of this Service Bulletin is at no
cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled in less than 60 months from its release date
(Basic Issue).
G. Material − Cost and Availability
No kit is necessary to do of this modification.
The parts in Paragraph 3.B. are necessary to do PART B, PART C and PART D of
this Service Bulletin.
The parts required to do PART B are available at no cost if:
− ordered during new aircraft warranty period, and
− a no−charge purchase order is sent to Bombardier Aviation in less than 60
months from this Service Bulletin release date (Basic Issue).
The parts required to do PART C and PART D are available at no cost for in and
out of warranty aircraft if a no−charge purchase order is sent to Bombardier
Aviation in less than 60 months from this Service Bulletin release date (Basic
Issue).
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 4 of 14

### Page 7

This Service Bulletin is covered by a dedicated schedule. To ensure a timely and
effective return/upgrade program, advance scheduling is required through our
In−Service Implementation Team (ISIT). Please contact your Regional Manager
(RM), Field Service Representative (FSR) or Customer Service Representative
(CSR) as soon as is practical to schedule your aircraft.
Bombardier Aviation is maintaining a rotable pool of replacement HSTA, to be
supplied to the operators under the terms and conditions given below:
NOTES: 1. The removed HSTA must be returned to Bombardier Aviation, Parts
Services in less than 10 days of receipt of replacement unit, with
documentation showing the serial number of the aircraft.
2. If the removed HSTA is not returned in less than 10 days, the
operator will be charged for the replacement unit.
Send removed HSTA, Part No. C47100−003 or C47100−004 for rework to
Bombardier Aviation at the address given below:
Learjet Inc. − Core Returns
251−A Wille Road,
Des Plaines, Illinois
60018−1861
USA
For all parts transactions, Bombardier Aviation’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
For those aircraft in new aircraft warranty at the time of Service Bulletin distribution,
Smart Parts does not pay for the kits or parts at any time.
For those aircraft out of new aircraft warranty at the time of Service Bulletin
distribution, Smart Parts pays only for the Kit CC84715−002 for up to 60 months
from the Service Bulletin distribution date (Basic Issue).
H. Tooling
The equipment and tools listed below are necessary to this modification.
GSE REFERENCE NO. PART NO. DESCRIPTION
20−00−04 − Inclonometer(See Note 4)
24−00−24 S4933959−501 Circuit Breaker Tag
27C−40−01 G1002740054−001 HSTA go−no go Gauge(See Note 4)
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 5 of 14

### Page 8

GSE REFERENCE NO. PART NO. DESCRIPTION
27C−40−05 CA14064−001
Tool, HSTA, Spanner,
Torque Adapter
(See Note 3)
27C−40−06 CA14065−001
Tool, HSTA Spanner
Wrench/Torque Adapter
(See Note 3)
27C−41−01 C84215−001 Shipping Bar(See Note 3)
27C−43−02 C47961−001 Jack, HSTA Scissor(See Note 3)
− CC92487−001
Leak Check Pressure
Tool Set
(See Note 5)
NOTES: 1. Refer to the BD−100 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM BD−100, for acceptable
GSE equivalents.
3. These tools are only necessary for PART D of this Service Bulletin.
4. These tools are only required for testing section.
5. This tool is only necessary for PART B of this Service Bulletin.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive (Pending).
− Bombardier Aviation, Restriction and/or Special Instruction (RSI),
C−100−000−27−0320, Rev. −−.
− MOOG, Service Bulletin C47100−27−02 (attached).
− MOOG, Service Bulletin C47100−27−03 (attached).
− Bombardier Aviation, SB 100−00−02, Service Bulletin Description and Policy.
− CH 300 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 27, 52 and 55.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 6 of 14

### Page 9

− CH 300 Aircraft Illustrated Parts Catalog (AIPC), Chapter 27.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapters 20 and 51.
− Bombardier Aviation, Structural Repair Manual (SRM), Chapter 51.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
− For the Challenger 350 aircraft, use Service Bulletin 350−27−009.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. If the HSTA is not installed in an aircraft (example: HSTA in the stock
room), go to step 2.B.(2) of this Service Bulletin.
2. All TASKs given in the procedures that follow are from the BD−100,
Aircraft Maintenance Manual unless otherwise specified.
3. All references made to zones, access panels and/or doors, are from the
BD−100, Aircraft Maintenance Manual, Chapter 6.
4. The intent of this Service Bulletin can be satisfied through a verification of
the airplane maintenance records if the part number of the installed HSTA
is C47100−004 and the serial number is found with suffix −K at the end
(example SER NO. 0000K). This means that these HSTA were already
inspected and repaired by the vendor (Moog) prior to release of the
Service Bulletin.
If it is the case, no inspection is required, and aircraft can be considered in
compliance with this Service Bulletin. If it is not the case, go to Paragraph
2.A. of this Service Bulletin.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all flight−control safety precautions. Refer to AMM 27−00−00−910−801.
(3) Install the applicable warning placards on the control wheels, control columns,
TRIM/STALL control panel, and from the area near the elevator control
surfaces and the horizontal stabilizer surface.
(4) Connect electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 7 of 14

### Page 10

(5) On the TRIM/STALL control panel, set the STAB trim switch to PRI.
(6) On the pilots control wheel, do the procedure that follows:
PROCEDURE APPLICABLE RESULT
Push in the pitch/roll trim switch, set
the switch to NOSE UP or NOSE
DOWN, and trim the horizontal
stabilizer surface to the neutral
position.
On the Engine Indication and Crew
Alerting System (EICAS) primary
page, make sure that the STAB trim
position indicator moves to the
neutral position and shows 1.9 to 2.1
units.
(7) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(8) Open the aft equipment−compartment door (182GL). Refer to
AMM 52−41−00−010−801.
(9) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP B15 PRI STAB TRIM / RUD LIM 211
RCBP B13 SEC STAB TRIM / RUD LIM 212
LDCPC A4 PRI STAB MOTOR 311
RDCPC A5 SEC STAB MOTOR 312
B. Special Check/Modification — PART A — Visual Check of the HSTA Serial
Numbers and Modification Plate
(1) Remove the forward access panel (346BR). Refer to
AMM 55−30−21−000−802.
(2) Examine the HSTA identification plate and make a record of the serial number.
If the serial number is found with suffix −K at the end (example
SER NO. 0000K), this means that these HSTA were already inspected and
repaired by the vendor (Moog) prior to release of the Service Bulletin and no
inspection is required. In this case, go to Paragraph 2.G (close out). If not, go
to step 2.B.(3).
(3) Examine the HSTA for modification plate installation as shown in Figure 3−11
of the Moog Service Bulletin C47100−27−02 or in Figure 3−1 of the Moog
Service Bulletin C47100−27−03. If the modification plate is not installed or if
SB C47100−27−02 or SB C47100−27−03 is not shown, go to step 2.B.(4). If
SB C47100−27−02 or SB C47100−27−03 is shown on the modification plate,
go to Paragraph 2.G (Close−out).
NOTE: Make sure to record the serial number on the Service Bulletin
Evaluation form, and fax or email the completed form to Bombardier
Aviation.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 8 of 14

### Page 11

(4) If the HSTA serial number is within the Moog SB C47100−27−02 effectivity list
referenced below, go to PART B of this Service Bulletin. If not, go to step
2.B.(5).
TABLE 2 - MOOG SB C47100-27-02 EFFECTIVITY
PART NO. NOMENCLATURE SERIAL NUMBERS
C47100−003
C47100−004
HORIZONTAL
STABILIZER
TRIM ACTUATOR
0001, 0002A, 0003−0096, 0098−0146,
0147A, 0148−0167, 0169−0236,
0238−0241, 0243−0302, 0304−0324,
0326−0336, 0338−0349, 0351−0528,
0530−0571, 0573−0636, 0638−0659,
0661−0808, 0812−0817, 0819, 0820
and 0825.
(5) If the HSTA serial number is within the Moog SB C47100−27−03 effectivity list
referenced below, go to PART C of this Service Bulletin.
TABLE 3 - MOOG SB C47100-27-03 EFFECTIVITY
PART NO. NOMENCLATURE SERIAL NUMBERS
C47100−003
C47100−004
HORIZONTAL
STABILIZER
TRIM ACTUATOR
0097A, 0168A, 0237A, 0242A, 0337A,
0350A, 0529A, 0572A, 0637A, 0660A,
0809, 0810, 0818, 0821−0824,
0826−0854, 0855A and 0856−0886.
NOTE: If none of the above conditions applies, contact Bombardier Aviation
for additional instructions.
C. Special Check/Modification — PART B — Moog SB C47100−27−02 − No−Back
Pawl Inspection and Re−identification
NOTES: 1. If it is not possible to complete all the instructions of this Service
Bulletin because of the configuration of the aircraft, submit an SRPSA
for analysis and to get an approved disposition to complete this
Service Bulletin.
2. Work instructions from Moog SB C47100−27−02 are separated into
two sections for "on−aircraft instructions" and for "on−bench
instructions". The on−bench instructions are only applicable if the
HSTA is not installed in an aircraft (example: HSTA in the stock
room). Refer to the applicable section of the SB C47100−27−02.
(1) Remove the forward access panel (346BL). Refer to
AMM 55−30−21−000−802.
(2) Get access to the HSTA no−back pawl assembly to perform visual inspection.
Refer to Moog Service Bulletin C47100−27−02.
(3) Incorporate Moog Service Bulletin C47100−27−02.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 9 of 14

### Page 12

(4) If the installed pawls are correctly installed,
(a) Complete Moog Service Bulletin C47100−27−02 and make sure to
re−identify the HSTA in accordance with Moog instruction, and
(b) Go to Paragraph 2.F (Testing).
(5) If the installed pawl are not correctly installed, go to PART D of this Service
Bulletin.
D. Special Check/Modification — PART C — Moog SB C47100−27−03 −
Modification Plate Addition
NOTE: If it is not possible to complete all the instructions of this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Get access to the HSTA to do installation of the modification plate. Refer to
Moog Service Bulletin C47100−27−03.
(2) Complete Moog Service Bulletin C47100−27−03 and make sure to re−identify
the HSTA in accordance with Moog instruction.
(3) Go to Paragraph 2.G (Close out).
E. Special Check/Modification — PART D — Replacement of HSTA
(1) Remove the HSTA, Part No. C47100−003 or C47100−004. Refer to
AMM 27−41−05−000−801.
(2) Send the removed HSTA, Part No. C47100−003 or C47100−004 for rework to
the address shown in Paragraph 1.G.
(3) Install a replacement unit HSTA, Part No. C47100−004. Refer to
AMM 27−41−05−400−801.
NOTE: The replacement HSTA shall have either a modification plate marked
with Moog SB C47100−27−02 or C47100−27−03 or identification
plate marked with the suffix −K at the end of the serial number.
(4) Go to Paragraph 2.F (Testing).
F. Testing
NOTE: Testing section is not applicable when the work is done on the bench.
Testing will be done per AMM instructions during HSTA installation
on−aircraft.
(1) Do the rigging check of the pitch trim system. Refer to
AMM 27−41−00−220−801.
(2) Do the operational test of the pitch trim system. Refer to
AMM 27−41−00−710−801.
(3) Go to Paragraph 2.G (Close out).
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 10 of 14

### Page 13

G. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) If applicable, install the LH−lower bullet−fairing panel (346CL). Refer to
AMM 55−30−21−400−804.
(2) If applicable, install the RH−lower bullet−fairing panel (346CR). Refer to
AMM 55−30−21−400−805.
(3) If applicable, install the forward access panel (346BL/346BR). Refer to
AMM 55−30−21−400−802.
(4) If applicable, install the lower visor fairing (346ALZ/346ARZ). Refer to
AMM 55−10−15−400−802.
(5) If applicable, install the upper visor fairing (346BLZ/346BRZ). Refer to
AMM 55−10−15−400−801.
(6) Remove the tag and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP B15 PRI STAB TRIM / RUD LIM 211
RCBP B13 SEC STAB TRIM / RUD LIM 212
LDCPC A4 PRI STAB MOTOR 311
RDCPC A5 SEC STAB MOTOR 312
(7) Close the aft equipment − compartment door (182GL). Refer to
AMM 52−41−00−410−801.
(8) Connect electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(9) On the TRIM/STALL control panel, set the STAB trim switch to PRI.
(10) Use the pilots control wheel to set the horizontal stabilizer to the neutral
position, refer to the procedure that follows:
PROCEDURE APPLICABLE RESULT
Push in the pitch/roll trim switch, set
the switch to NOSE UP or NOSE
DOWN, and trim the horizontal
stabilizer surface to the neutral
position.
On the engine indication and crew
alerting system (EICAS) primary
page, make sure that the STAB trim
position indicator moves to the
neutral position and shows 1.9 to
2.1 units.
(11) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 11 of 14

### Page 14

(12) Remove the warning placards from the control wheels, control columns,
TRIM/STALL control panel, elevator control surfaces, and the horizontal
stabilizer surface.
(13) Remove all tools, equipment and unwanted materials from the aircraft.
H. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
The part that follows is necessary to do PART B of this Service Bulletin and is
available from Bombardier Aviation Parts Services, Montreal.
NEW PART
NO. QTY ITEM USED PARTNO. INSTRUCTIONS-DISPOSITION
CA86497−003 1 KIT BRAYCO − −
CC84715−002 1 MATERIALKIT − −
The part that follows is necessary to do PART C of this Service Bulletin and is
available from Bombardier Aviation Parts Services, Montreal.
NEW PART
NO. QTY ITEM USED PARTNO. INSTRUCTIONS-DISPOSITION
CC89222−002 1 MOD PLATE − −
The part that follows is necessary to do PART D of this Service Bulletin and is
available from Bombardier Aviation Parts Services, Montreal.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 12 of 14

### Page 15

NEW PART NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
C47100−004
(See Note 2 and 3) 1
HORIZONTAL
STAB TRIM
ACTUATOR
C47100−003
or
C47100−004
Refer to
Paragraph 1.G.
NOTES: 1. The part number for the item listed above is subject to change without
revision to this Service Bulletin. In case of discrepancy between this
list and any other list, the Illustrated Parts Catalog prevails and shall
be used to determine the latest part number.
2. Only required when HSTA replacement is applicable (Pawls
installation not acceptable per VSB C47100−27−02).
3. The replacement HSTA shall have either a modification plate marked
with Moog SB C47100−27−02 or C47100−27−03 or identification
plate marked with the suffix −K at the end of the serial number.
C. Material
The materials that follow are necessary to do this Service Bulletin. These can be
purchased from a local supplier. Bombardier Aviation does not pay for these
consumables.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE)
Anti−Sabotage
Lacquer
or equivalent
(as noted in
the VSB
C47100−27−02)
(See Note 1)
C51205
or
C51428
or
EC 1252
(tamper proof)
or
F−910
or
equivalent
− As Necessary Code: A
Coating
Compound −
CLEAR
or equivalent
(as noted in
the VSB
C47100−27−02
and 03)
(See Note 2)
A38662
(CATALYST
X−310A)
(683−3−2
AKZO
NOBEL
or equivalent)
− As Necessary Code: A
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 13 of 14

### Page 16

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE)
Lockwire
CRES 0.020
in.
(See Note 3)
MS20995C20 − As Necessary Code: A
NOTES: 1. Refer to SPM 51−31−00, reference item 09−120 and 09−121 as
equivalent.
2. Refer to SRM 51−31−02 for equivalent that meet the BAMS 565−002
or 565−009 specification.
3. Refer to SPM 20−50−00, reference item 05−240. The manufacturer
reference/specification is MS20995C20.
4. Refer to the table that follows for each suppliers address listed by
codes.
5. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
6. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Commercially Available
D. Publications
No publications required.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Nov 09/2020
Revision 01: Dec 01/2020
100−27−20
Page 14 of 14

### Page 17

100−27−20 Rev. 01 Dec 01/2020
SPECIAL CHECK/MODIFICATION – HORIZONTAL STABILIZER –
NO−BACK ASSEMBLY PAWL INSPECTION
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 18

SERVICE BULLETIN INCORPORATION SHEET − "100−27−20"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
100−27−20 01
COMPLIED WITH
YES    NO    N/A
PART A
PART B
PART C
PART D
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
