# Bombardier Service Bulletin 100-27-22

Copy: No revision named ("SB 100-27-22 Revision Basic"), 34 pages: PDF https://openairdocs.org/files/sha256/dd/2d/dd2d87d282e1b08af2b71d3a8a20bf44fca345b0c27a76883cc6b9d41148f7e1; text https://openairdocs.org/service-documents/bombardier/sb-100-27-22/file/dd2d87d282e1.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-2023; AD 2025-02-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-27-22
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-27-22

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2025-02-01](https://openairdocs.org/ad/2025-02-01.md), effective Mar 17, 2025: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-27-22/proposed.md).

## Text (34 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2024-2023; AD 2025-02-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

MODIFICATION – PITCH TRIM SYSTEM –
INSTALLATION OF PITCH/ROLL TRIM SWITCH RELAYS
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 20003 to 20500
MANPOWER: 45 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION NOYES
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for kit, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 27−41
FLIGHT CONTROLS
Basic Issue: Dec 29/2022 100−27−22
Page 1 of 1
This Service Bulletin is available at:

### Page 2

MODIFICATION – PITCH TRIM SYSTEM –
INSTALLATION OF PITCH/ROLL TRIM SWITCH RELAYS
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. They can be reached at
bacs_isit@aero.bombardier.com. The parts will be allocated on a first
come first serve basis.
Should you require additional information, please contact your Regional
Sales Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 100−00−002.
A. Effectivity
BD−100−1A10 aircraft, Serial No. 20003 to 20500.
The intent of this Service Bulletin was met on the aircraft that follow with the
Pre−Published Service Bulletin 100−27−22 listed below:
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 27−41
FLIGHT CONTROLS
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2022 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Dec 29/2022 100−27−22
Page 1 of 31
This Service Bulletin is available at:

### Page 3

AIRCRAFT SERIAL NO. PRE-PUBLISHED DATE
20277 Oct 25/2022
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
It was found that the pilot and co−pilot trim Enable/Arm switch signals are not
segregated. This condition, combined with failure of the pilot pitch/roll trim
switch, can lead to an uncommanded horizontal stabilizer motion.
2. Objective/Benefit:
This Service Bulletin provides instructions to modify the electrical circuitry
connecting the pitch/roll trim switches to the aileron trim actuator and to the
HSTECU. Changes include, amongst other things, the introduction of new
relays and associated wiring. The changes ensure the pilot and co−pilot trim
Enable/Arm switch signals remain segregated in both roll and pitch axes.
C. Description
This Service Bulletin gives instructions to:
− Get access to the avionic rack,
− Rework the plate assembly,
− Install the relay bracket assembly,
− Install the relays,
− Do the wiring installation for the relays, and
− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Specified Time Compliance
Recommended within 3000 flight hours or 60 months, whichever comes first from
this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin. Standard
SRPSA fees may apply. Refer to the Services section of the Bombardier
customer portal for the latest prices, rates and fees.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 2 of 31

### Page 4

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU Bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 100−00−002.
2. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection. Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
45 man−hours are necessary to do this modification.
Bombardier Aviation does not pay for the labor to do this Service Bulletin.
G. Material − Cost and Availability
Kit 350K27−012 is necessary to do this modification. For material data, refer to
Paragraph 3.C.
KIT NO. PRICE
350K27−012
Please contact Bombardier Aviation Parts Services, in
Montreal, for delivery lead times and confirmation of
prices.
Bombardier Aviation does not pay for the kit to do this Service Bulletin.
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are
used to reserve and manage inventory due to limited availability of rotable stock,
parts and/or kits. Parts are limited, therefore, advance part scheduling with our
In−Service Implementation Team (ISIT) is recommended prior to a maintenance
visit. They can be reached at bacs_isit@aero.bombardier.com. The parts will be
allocated on a first come first serve basis.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 3 of 31

### Page 5

Should you require additional information, please contact your Regional Sales
Manager (RM) or Field Service Representative (FSR).
For more information on dedicated schedules, refer to SB 100−00−002.
For those aircraft in new aircraft warranty at the time of Service Bulletin distribution,
Smart Parts does not pay for the kit at any time.
For those aircraft out of new aircraft warranty at the time of Service Bulletin
distribution, Smart Parts pays for the kit up to 12 months from Service Bulletin
distribution date (Basic Issue).
H. Tooling
The equipment and tools listed below are necessary to do this modification:
GSE REFERENCE NO. PART NO. DESCRIPTION
24−00−24 S4933959−501 Tag, Circuit Breaker
Commercially Available − Brush, CRES Wire
Commercially Available − Grip Measurement Gauge
Commercially Available − Rivet Installation Tools
Commercially Available − Torque Wrench
NOTES: 1. Refer to the BD−100 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for the BD−100 for
acceptable GSE equivalents.
3. This list is provided for a quick reference. In case of discrepancy
between this list and the tool called out in the SPM−WM, Chapter 20,
then the tool called in the SPM−WM will prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
WEIGHT MOMENT
+0.14 pounds (0.06 kg) +45.03 pound−inches (0.52 kgm)
J. Electrical Load Data
This modification increases the continuous load as follows:
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 4 of 31

### Page 6

BUS AMPS KW KVAR
L ESS 0.05 amps(continuous) − −
R ESS 0.05 amps(continuous) − −
K. References
− TCCA Airworthiness Directive (pending).
− Bombardier Aviation, Modification Summary, BB100T011116, Rev. A−2.
− Bombardier Aviation, Kit Drawing K1000070494, Rev. A.
− Bombardier Aviation, Kit Drawing K1002710003, Rev. A.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapters 20 and 51.
− CH 300 Aircraft Maintenance Manual (AMM), Chapters 6, 24, 25, 26, 27, 32, 34
and 52.
− CH 300 Aircraft Illustrated Parts Catalog (AIPC), Chapters 25 and 27.
− CH 300 Structural Repair Manual (SRM), Chapter 51.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
− For the Challenger 350 aircraft, use Service Bulletin 350−27−012.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the BD−100,
Aircraft Maintenance Manual unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
BD−100, Aircraft Maintenance Manual, Chapter 6.
A. Aircraft Setup
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all electrostatic−discharge safety precautions. Refer to
AMM 24−00−00−910−802.
(3) Obey all flighty−control safety precautions. Refer to AMM 27−00−00−910−801.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 5 of 31

### Page 7

WARNING: DO NOT OPEN THE L OR R PROBE CTRL CIRCUIT BREAKERS
WITH ONE OR ALL OF THE PROBE POWER CIRCUIT BREAKERS
PUSHED IN. THE PROBES CAN BE HOT AND CAUSE INJURY TO
PERSONS AND DAMAGE TO THE EQUIPMENT.
(4) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(5) Remove the external DC power from the aircraft. Refer to
AMM 24−41−00−861−802.
(6) Put a warning placard on the external power control panel to make sure that
electrical power is not applied.
(7) Disconnect the batteries. Refer to AMM 24−32−00−040−801.
(8) Remove the equipment rack access panels (221AZ/222AZ, 221BZ, 221DZ,
222EZ). Refer to AMM 25−72−01−000−803.
(9) Open the aft equipment−compartment door (182GL). Refer to
AMM 52−41−01−010−801.
(10) Remove the aft lower nose−compartment panels (141BL/142BR). Refer to
AMM 52−45−01−000−801.
(11) Remove the bulkhead access panel. Refer to AIPC 25−12−13, Item 70.
(12) Remove the LRU and tray that follow from the L/H avionic rack:
(a) Remove the junction box JB3. Refer to AMM 24−63−09−000−802.
(b) Remove the JB3 tray. Refer to AMM 24−63−11−000−801.
(13) Remove the LRU and tray that follow from the R/H avionic rack:
(a) Remove the junction box JB4. Refer to AMM 24−63−13−000−802.
(b) Remove the JB4 tray. Refer to AMM 24−63−15−000−801.
(c) Remove the terrain−avoidance warning system (TAWS) computer. Refer
to AMM 34−42−01−000−802.
(14) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP B15 PRI STAB TRIM/RUD LIM 211
RCBP B13 SEC STAB TRIM/RUD LIM 212
RCBP B15 AIL TRIM 212
LDCPC A4 PRI STAB MOTOR 311
RDCPC A5 SEC STAB MOTOR 312
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 6 of 31

### Page 8

B. Modification — Installation of Pitch/Roll Trim Switch Relays
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the rework of the plate assembly, Part No. 1005336375, as follows. Refer
to Kit Drawing K1000070494, Section B−B.
(a) Drill holes (qty 2) of diameter 0.220 to 0.226 in (5.59 to 5.74 mm), thru the
plate assembly, Part No. 1005336375, at the locations shown in Kit
Drawing K1000070494, Section B−B.
(b) Install the nut plates, Part No. NAS1474A3 (qty 2), on the plate assembly,
Part No. 1005336375, with rivets, Part No. CCR244CS−3−04. Refer to
SRM 51−42−16.
(c) Re−identify the plate assembly as K1000070494−101 per best shop
practice.
(d) Prepare the mating surface to the bracket of the plate assembly, Part
No. K1000070494−101 for electrical bonding. Refer to
SPM−MM 51−80−00.
(2) Prepare the mating surfaces to plate of the bracket assembly, Part
No. 1005324754−001 for electrical bonding. Refer to SPM−MM 51−80−00.
(3) Install the relay bracket assembly, Part No. 1005324754−001, on the plate
assembly, Part No. K1000070494−101, with screws, Part
No. NAS1801−3−7 (qty 2), and washers, Part No. NAS1149F0332P (qty 2).
Refer to SRM 51−41−04 and Kit Drawing K1000070494, Section C−C.
(4) Do the electrical bonding resistance check of the bracket assembly, Part
No. 1005324754−001. Refer to SPM−MM 51−80−00. Make sure that the
maximum bonding resistance is 0.0025 Ω (2.5 mΩ).
(5) Install the relays, Part No. M83536/6−022M on the far side of relay bracket
assembly, Part No. 1005324754−001. Refer to SPM−MM 20−39−00−02 and
Kit Drawing K1000070494, Section D−D.
(6) Install the ground return stacks on the relay bracket assembly, Part
No. 1005324754−001, as follows. Refer to Kit Drawing K1000070494,
Section D−D.
(a) Prepare the surfaces of the ground return stack for electrical bonding.
Refer to SPM−MM 51−80−00.
(b) Install the screw, Part No. MS35206−231, and the washers, Part
No. MS35338−41 and NAS1149DN632J, on the far side of the relay
bracket assembly, Part No. 1005324754−001.
(c) Install the washer, Part No. NAS1149DN632J, and the nut, Part
No. MS35649−262, on the near side of the relay bracket assembly, Part
No. 1005324754−001. Refer to SRM 51−41−04.
(d) Install the bonding lug, washers, Part No. NAS1149DN632J and
MS35338−41, and the nut, Part No. MS35649−262. Refer to
SRM 51−41−04.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 7 of 31

### Page 9

(e) Do the electrical bonding test between the electrical ground stud and
primary structure. Refer to SPM−MM 51−80−00. Make sure that the
maximum bonding resistance is 0.0025 Ω (2.5 mΩ).
(f) Apply HumiSeal all around the ground return stacks. Refer to
SPM−MM 20−41−00.
(g) Prepare and install the applicable electrical idents, Part
No. K1000070494−003, near the ground return stacks. Refer to
SPM−MM 20−10−10 and 20−80−01.
(7) Touch−up the mating interface of the plate assembly, Part
No. K1000070494−101 and relay bracket assembly, Part
No. 1005324754−001, per finish code X060. Refer to SRM 51−01−04.
(8) Do the wiring installation for the relays, Part No. M83536/6−022M, as per Kit
Drawing K1002710003.
(9) Install the LRU and tray that follow in the L/H avionic rack:
(a) Install the JB3 tray. Refer to AMM 24−63−11−400−801.
(b) Install the junction box JB3. Refer to AMM 24−63−09−400−802.
(10) Install the LRU and tray that follow in the R/H avionic rack:
(a) Install the terrain−avoidance warning system (TAWS) computer. Refer to
AMM 34−42−01−400−802.
(b) Install the JB4 tray. Refer to AMM 24−63−15−400−801.
(c) Install the junction box JB4. Refer to AMM 24−63−13−400−802.
C. Testing
(1) Remove the tags and close the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP B15 PRI STAB TRIM/RUD LIM 211
RCBP B13 SEC STAB TRIM/RUD LIM 212
RCBP B15 AIL TRIM 212
LDCPC A4 PRI STAB MOTOR 311
RDCPC A5 SEC STAB MOTOR 312
(2) Connect the batteries. Refer to AMM 24−32−00−440−801.
(3) Connect the electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(4) Connect and energize the external DC power. Refer to
AMM 24−41−00−861−801.
(5) Install the equipment rack access panel (221AZ/222AZ, 221BZ, 221DZ,
222EZ). Refer to AMM 25−72−01−400−803.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 8 of 31

### Page 10

(6) Install the aft lower nose−compartment panels (141BL/142BR). Refer to
AMM 52−45−01−400−801.
(7) Install the bulkhead access panel. Refer to AIPC 25−12−13, Item 70.
(8) Do the aileron trim tab travel check as follows:
(a) With the tab at its neutral position, attach to the trim tab a suitable test
fixture to measure trim tab angular displacement. On the pilot’s handwheel
trim switch, depress the trim enable switch and move the trim knob to the
Left Wing down (LWD) position and hold. Verify that the tab moves
Trailing Edge Down (TED) until it reaches the travel stop. Release the trim
switch.
NOTE: While the aileron trim tab is in motion, verify that the analog
aileron trim indication needle on EICAS moves smoothly and
doesn’t stop moving while the actuator is still in motion.
(i) Record the tab deflection at the LWD full travel stop. Tab deflection
shall be 20°±1° TED.
(ii) Verify that the needle on the analog display indicates full LWD trim.
(b) On the pilot’s handwheel trim switch, depress the trim enable switch and
move the trim knob to the Right Wing Down (RWD) position and hold.
Verify that the tab moves Trailing Edge Up (TEU) until it reaches the travel
stops. Release the trim switch.
NOTE: While the aileron trim tab is in motion, verify that the analog
aileron trim indication needle on EICAS moves smoothly and
doesn’t stop moving while the actuator is still in motion.
(i) Record the tab deflection at the RWD full travel stop. Tab deflection
shall be 20°±1° TEU.
(ii) Verify that the needle on the analog display indicates at least full
RWD trim. (It is permissible for the analog needle to be beyond the
full RWD trim tick mark).
(c) Using the pilot’s handwheel trim switch, drive the aileron trim actuator
back to its neutral (’0’) position. With the tab at its neutral position, move
the pilot’s trim knob to the LWD and then RWD position without
depressing the trim enable switch and verify there is no movement in
either direction of the aileron trim tab.
(d) Return the tab to the neutral position using the pilot’s handwheel trim
switch. Repeat the tests of steps (a), (b) and (c), using the copilot’s trim
switch.
(e) Using the pilot’s handwheel trim switch, drive the aileron trim actuator
back to its neutral (’0’) position. With the tab at its neutral position, move
the pilot’s trim knob to the LWD and then RWD position while depressing
the copilot’s trim enable switch and verify there is no movement in either
direction of the aileron trim tab.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 9 of 31

### Page 11

(f) Using the copilot’s handwheel trim switch, drive the aileron trim actuator
back to its neutral (’0’) position. With the tab at its neutral position, move
the copilot’s trim knob to the LWD and then RWD position while
depressing the pilot’s trim enable switch and verify there is no movement
in either direction of the aileron trim tab.
(g) Return the tab to the neutral position. On the pilot’s handwheel, only
depress the trim enable switch without moving the trim knob. Verify there
is no movement of the aileron trim tab.
(h) Return the tab to the neutral position. On the copilot’s handwheel, only
depress the trim enable switch without moving the trim knob. Verify there
is no movement of the aileron trim tab.
(i) Using either the pilot’s or copilot’s handwheel trim switches (trim enable
switch and trim knob), command a full travel (stop to stop) actuation,
recording the travel time. The stop−to−stop, no−load travel time shall be
32 ± 6 seconds.
(9) Do the aileron trim tab pilot override check as follows:
(a) With the tab at the neutral position, depress the copilot’s trim enable
switch and move the trim knob to the LWD position and hold. Immediately
depress the pilot’s trim enable switch and move the trim knob to the RWD
position and hold. Verify that the pilot’s trim switch overrides the copilot’s
by ensuring that the tab moves TEU and the EICAS display is moving to
the right.
(b) Repeat step 7.(a) with an initial RWD command on the copilot’s trim
switch. Immediately command LWD on the pilot’s trim switch and hold.
Verify that the pilot’s trim switch overrides the copilot’s by ensuring that the
tab moves TED and the EICAS display is moving to the left.
(10) Do the master disconnect switch (MSW) check as follows:
(a) With the tab in the neutral position, depress the pilot’s trim enable switch
and move the trim knob to the LWD position and hold.
(i) While the tab is moving TED, depress the pilot’s wheel master
disconnect (MSW) switch on the handwheel and hold. Verify that tab
motion has stopped. Release the pilot’s wheel master switch (MSW)
and verify that the tab continues to move TED.
(b) While the tab is again moving TED, depress the copilot’s wheel master
disconnect switch (MSW) on the handwheel and hold. Verify that tab
motion has stopped. Release the copilot’s wheel master switch (MSW)
and verify that the tab continues to move TED.
(c) Repeat steps (a) through (b), using the copilot’s trim switch in the RWD
position (tab moving TEU) and again check both wheel master disconnect
switches.
(d) Return the actuator to the neutral position (’0’ trim units and centered
needle on EICAS) and open the AIL TRIM circuit breaker (CB2−B15).
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 10 of 31

### Page 12

(i) Depress the pilot’s trim enable switch and move the trim knob to the
LWD and then RWD positions verifying that the tab and EICAS
indications do not move. Repeat for the copilot’s handwheel trim
switch, verifying that neither the tab nor the EICAS indications move.
(ii) Close the AIL TRIM circuit breaker (CB2−B15).
(11) Make sure that circuit breakers that follow are closed:
CB PANEL CB NO. NAME ZONE
LCBP B6 L IAPS 211
RCBP B6 R IAPS 212
(12) Open the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP B15 PRI STAB TRIM/RUD LIM 211
RCBP B13 SEC STAB TRIM/RUD LIM 212
LDCPC A4 PRI STAB MOTOR 311
RDCPC A5 SEC STAB MOTOR 312
(13) Do the Power−On, Circuit Breaker, and Cockpit Switches Tests as follows:
(a) Set the Pitch Trim PRI/OFF/SEC switch to the PRI position.
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is
displayed on EICAS.
(b) Close the PRI STAB TRIM/RUD LIM circuit breaker (CB1−B15).
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is
displayed on EICAS.
(c) Close the SEC STAB MOTOR circuit breaker (CB6−A5).
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is
displayed on EICAS.
(d) Depress the pilot’s trim enable switch and move the trim knob in the nose
up (NU) and nose down (ND) directions.
(i) Make sure that no stabilizer trim motion occurs on the synoptic
display.
(e) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up (NU) and nose down (ND) directions.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 11 of 31

### Page 13

(i) Make sure that no stabilizer trim motion occurs on the synoptic
display.
(f) Open the SEC STAB MOTOR circuit breaker (CB6−A5).
(g) Close the PRI STAB MOTOR circuit breaker (CB5−A4).
(i) Make sure that no stabilizer trim messages are displayed on EICAS.
(h) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(i) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(j) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(k) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(l) Depress the pilot’s trim enable switch and move the copilot’s trim knob in
the nose up direction.
(i) Make sure that there is no stabilizer motion.
(m) Depress the pilot’s trim enable switch and move the copilot’s trim knob in
the nose down direction.
(i) Make sure that there is no stabilizer motion.
(n) Depress the co−pilot’s trim enable switch and move the pilot’s trim knob in
the nose up direction.
(i) Make sure that there is no stabilizer motion.
(o) Depress the co−pilot’s trim enable switch and move the pilot’s trim knob in
the nose down direction.
(i) Make sure that there is no stabilizer motion.
(p) Depress the pilot’s trim enable switch without moving the trim knob in the
nose up or down direction.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 12 of 31

### Page 14

(i) Make sure that there is no stabilizer motion.
(q) Depress the co−pilot’s trim enable switch without moving the trim knob in
the nose up or down direction.
(i) Make sure that there is no stabilizer motion.
(r) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
LWD direction.
(i) Make sure that there is no stabilizer motion.
(s) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
RWD direction.
(i) Make sure that there is no stabilizer motion.
(t) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the LWD direction.
(i) Make sure that there is no stabilizer motion.
(u) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the RWD direction.
(i) Make sure that there is no stabilizer motion.
(v) Select the Pitch Trim PRI/OFF/SEC switch to the OFF position.
(i) Make sure that the STAB TRIM OFF white (status) message is
displayed on EICAS.
(w) Depress the pilot’s trim enable switch and move the trim knob in the nose
up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(x) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(y) Select the Pitch Trim PRI/OFF/SEC switch to the SEC position.
(i) Make sure that the SEC STAB TRIM FAIL amber (caution) message
is displayed on EICAS.
(z) Depress the pilot’s trim enable switch and move the trim knob in the nose
up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(aa) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 13 of 31

### Page 15

(ab) Open the PRI STAB TRIM/RUD LIM circuit breaker (CB1−B15).
(ac) Close the SEC STAB TRIM/RUD LIM (CB2−B13) circuit breaker.
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) and a SEC
STAB TRIM FAIL amber (caution) message are displayed on EICAS.
(ad) Depress the pilot’s trim enable switch and move the trim knob in the nose
up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(ae) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(af) Open the PRI STAB MOTOR circuit breaker (CB5−A4).
(ag) Close the SEC STAB MOTOR circuit breaker (CB6−A5).
(i) Make sure that the SEC STAB TRIM ON white (status) message is
displayed on EICAS.
(ii) Make sure the PRI STAB TRIM FAIL amber (caution) message is
displayed on EICAS.
(ah) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(ii) Make sure that the stabilizer trim motion occurs.
(ai) Depress the pilot’s trim enable switch and move the pilot’s trim knob in the
nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(ii) Make sure that the stabilizer trim motion occurs.
(aj) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(ii) Make sure that the stabilizer trim motion occurs.
(ak) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 14 of 31

### Page 16

(ii) Make sure that the stabilizer trim motion occurs.
(al) Select the Pitch Trim PRI/OFF/SEC switch to the OFF position.
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message
and STAB TRIM OFF white (status) message are displayed on
EICAS.
(am)Depress the pilot’s trim enable switch and move the trim knob in the nose
up and nose down directions.
(i) Make sure that no stabilizer trim motion occurs.
(an) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up and nose down directions.
(i) Make sure that no stabilizer trim motion occurs.
(ao) Select the Pitch Trim PRI/OFF/SEC switch to the PRI position.
(i) Make sure that the PRI STAB TRIM FAIL amber (caution) message is
displayed on EICAS.
(ap) Depress the pilot’s trim enable switch and move the trim knob in the nose
up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(aq) Depress the co−pilot’s trim enable switch and move the trim knob in the
nose up and nose down directions.
(i) Make sure that no stabilizer trim occurs.
(ar) Close the PRI STAB TRIM/RUD LIM circuit breaker (CB1−B15).
(as) Close the PRI STAB MOTOR circuit breaker (CB5−A4).
(i) Make sure that no stabilizer trim EICAS messages are displayed.
(at) Select the Pitch Trim PRI/OFF/SEC switch to the SEC position.
(i) Make sure that the SEC STAB TRIM ON white (status) message is
displayed on EICAS, and no other stabilizer trim EICAS messages
are displayed.
(14) Do the Trim Rate, Trim Clacker, and Disconnect Switch Tests as follows:
(a) Set the Pitch Trim PRI/OFF/SEC switch to the SEC position.
(i) Using the stopwatch, measure how long it takes to trim NU 5 units.
(ii) Make sure that the Trim Clacker aural warning sounds after three (3)
seconds.
(iii) Make sure that the elapsed time is 25 +/−3 seconds.
(b) Using the stopwatch, measure how long it takes to trim ND 5 units.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 15 of 31

### Page 17

(i) Make sure that the Trim Clacker aural warning sounds after three (3)
seconds.
(ii) Make sure that the elapsed time is 25 +/−3 seconds.
(c) Command trim in the NU direction an press the pilot’s Disconnect Switch.
(i) Make sure that the trim motion stops immediately and then release
the pilot’s Disconnect Switch.
(d) Command trim in the ND direction and press the Co−pilot’s Disconnect
Switch.
(i) Make sure that the trim motion stops immediately and then release
the Co−pilot’s Disconnect Switch.
(e) Select the Pitch Trim PRI/OFF/SEC switch to the PRI position.
(f) Command the trim in the NU direction and press the pilot’s Disconnect
Switch.
(i) Make sure that trim motion stops immediately and then release the
pilot’s Disconnect Switch.
(g) Command trim in the ND direction and press the Co−pilot’s Disconnect
Switch.
(i) Make sure that the trim motion stops immediately and then release
the Co−pilot’s Disconnect Switch.
(h) Using the stopwatch, measure how long it takes to trim NU 5 units.
(i) Make sure that the Trim Clacker aural warning sounds after three (3)
seconds.
(ii) Make sure that no stabilizer trim EICAS messages are annunciated.
(iii) Make sure that the elapsed time is 12.5 +/−1.5 seconds.
(i) Using the stopwatch, measure how long it takes to trim ND 5 units.
(i) Make sure that the Trim Clacker aural warning sounds after three (3)
seconds.
(ii) Make sure that no stabilizer trim EICAS messages are annunciated.
(iii) Make sure that the elapsed time is 12.5 +/−1.5 seconds.
(15) Do the Pilot Override Authority Tests as follows:
(a) Set the Pitch Trim PRI/OFF/SEC switch to the PRI position.
(b) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 16 of 31

### Page 18

(c) While the trim is moving nose up, depress the pilot’s trim enable switch
and move the pilot’s trim knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(d) Release both the pilot’s and co−pilot’s trim switches.
(e) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(f) While the trim is moving nose down, depress the pilot’s trim enable switch
and move the pilot’s trim knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(g) Release both the pilot’s and co−pilot’s trim switches.
(h) Set the Pitch Trim PRI/OFF/SEC switch to the SEC position.
(i) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(j) While the trim is moving nose up, depress the pilot’s trim enable switch
and move the pilot’s trim knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(k) Release both the pilot’s and co−pilot’s trim switches.
(l) Depress the co−pilot’s trim enable switch and move the co−pilot’s trim
knob in the nose down direction.
(i) Make sure that the stabilizer trims in the nose down direction on the
synoptic display.
(m) While the trim is moving nose down, depress the pilot’s trim enable switch
and move the pilot’s trim knob in the nose up direction.
(i) Make sure that the stabilizer trims in the nose up direction on the
synoptic display.
(n) Release both the pilot’s and co−pilot’s trim switches.
(16) Do the functional test of the junction box JB3. Refer to
AMM 24−63−09−720−801.
(17) Do the operational test of the fire extinguishing system. Refer to
AMM 26−21−00−710−801.
(18) Do the operational test of the FIREX. Refer to AMM 26−11−00−710−801.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 17 of 31

### Page 19

(19) Do the operational test of the APU fire extinguishing system. Refer to
AMM 26−21−00−710−803.
(20) Do the operational test of the aileron trim actuator. Refer to
AMM 27−12−05−710−801.
(21) Do the functional test of the TCAS. Refer to AMM 34−43−00−710−801.
(22) Do the functional test of the junction box JB4. Refer to
AMM 24−63−13−720−801.
(23) Do the operational test of the TAWS computer. Refer to
AMM 34−42−01−710−802.
(24) Do the operational test of the extension and retraction system. Refer to
AMM 32−30−00−710−801.
D. Close−out
(1) On the TRIM/STALL control panel, set the STAB trim switch to PRI.
(2) Use the pilots control wheel to set the horizontal stabilizer to the neutral
position, refer to the procedure that follows:
PROCEDURE APPLICABLE RESULTS
Push in the pitch/roll trim switch,
set the switch to NOSE UP or
NOSE DOWN, and trim the
horizontal stabilizer surface to
the neutral position.
On the engine indication and crew
alerting system (EICAS) primary page,
make sure that the STAB trim position
indicator moves to the neutral position
and shows 1.9 to 2.1 units. − set the
aileron trim actuator to neutral
(3) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
(4) Remove the warning placards.
(5) Remove all tools, equipment and unwanted materials from the aircraft.
(6) Close the aft equipment−compartment door (182GL). Refer to
AMM 52−41−01−410−801.
E. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 18 of 31

### Page 20

3. MATERIAL INFORMATION
A. Kit
Kit 350K27−012 is necessary to do this Service Bulletin and contains the parts that
follow:
NEW PART NO. QTY ITEM USEDPART
NO.
INSTRUCTIONS
- DISPOSITION
CCR244CS−3−04 4 Rivet, Blind, 100° − −
K1000070494−003/01 1 Electrical Ident Kit − −
K1002710003/01 1 Wire Kit − −
MS35206−231 2 Screw, Pan Head − −
MS35338−41 4 Washer, Lock − −
MS35649−262 4 Nut, Plain,Hexagon − −
M12883/44−01 2 Relay, Socket − −
M83536/6−022M 2 Relay − −
NAS1149DN632J 6 Washer, Flat − −
NAS1149F0332P 2 Washer − −
NAS1474A3 2 Nutplate − −
NAS1801−3−7 2 Screw, Hex HD − −
1005324754−001 1 Bracket, Relay − −
NOTES: 1. In case of discrepancy between this list and the Service Bulletin Kit
Parts List contained in the respective kit, then the later list prevails.
2. The actual quantity for some of the hardware contained in the kit can
be greater than the amount shown in the table as these items are
supplied in prepackaged quantities.
B. Parts
No parts required.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 19 of 31

### Page 21

C. Material
The materials that follow are necessary to do this Service Bulletin. These can be
purchased from a local supplier. Bombardier Aviation does not pay for this
consumable.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Abrasive
paper − − As Necessary Code: A
Alodine
1132 − MIL−DTL−81706,Class 1A As Necessary Code: A
Cloth,
Cleaner,
Low−lint
− − As Necessary Code: A
Fluid resistant
Epoxy Primer − BAMS 565−001 As Necessary Code: A
HumiSeal − − As Necessary Code: A
Sharp Knife − − As Necessary Code: A
Spatula − − As Necessary Code: A
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Commercially Available
D. Publications
No publications required.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 29/2022 100−27−22
Page 20 of 31

### Page 22

SB350−27−012−70494−A−S1−PL 
MODEL BD−100−1A10 (CH−300)
PL K1000070494 − Kit − Trim Switch − Relay Installation
(Sheet 1 of 2, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 21 of 31

### Page 23

SB350−27−012−70494−A−S2−PL 
MODEL BD−100−1A10 (CH−300)
PL K1000070494 − Kit − Trim Switch − Relay Installation
(Sheet 2 of 2, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 22 of 31

### Page 24

SB350−27−012−70494−A−S1−1 
MODEL BD−100−1A10 (CH−300)
K1000070494 − Kit − Trim Switch − Relay Installation
(Sheet 1 of 1, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 23 of 31

### Page 25

SB350−27−012−70494−A−S1−2 
MODEL BD−100−1A10 (CH−300)
K1000070494 − Kit − Trim Switch − Relay Installation
(Sheet 1 of 1, Rev. A, continued)
Basic Issue: Dec 29/2022 100−27−22
Page 24 of 31

### Page 26

SB350−27−012−10003−A−S1 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Diagram Pitch/Roll Trim Enable Circuit
(Sheet 1 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 25 of 31

### Page 27

SB350−27−012−10003−A−S2 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 2 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 26 of 31

### Page 28

SB350−27−012−10003−A−S3 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 3 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 27 of 31

### Page 29

SB350−27−012−10003−A−S4 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 4 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 28 of 31

### Page 30

SB350−27−012−10003−A−S5 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 5 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 29 of 31

### Page 31

SB350−27−012−10003−A−S6 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 6 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 30 of 31

### Page 32

SB350−27−012−10003−A−S7 
MODEL BD−100−1A10 (CH−300)
K1002710003 − Kit − Wiring Digram Pitch/Roll Trim Enable Circuit
(Sheet 7 of 7, Rev. A)
Basic Issue: Dec 29/2022 100−27−22
Page 31 of 31

### Page 33

100−27−22 Basic Dec 29/2022
MODIFICATION – PITCH TRIM SYSTEM –
INSTALLATION OF PITCH/ROLL TRIM SWITCH RELAYS
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 34

SERVICE BULLETIN INCORPORATION SHEET − "100−27−22"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
100−27−22 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
