# Bombardier Service Bulletin 100-32-30

Copy: No revision named ("100-32-30 Basic"), 17 pages: PDF https://openairdocs.org/files/sha256/f3/78/f378584fb4347d4e7e0f31b738c7a47a25c10d7dfd2806e3c8e7fb564d833d35; text https://openairdocs.org/service-documents/bombardier/sb-100-32-30/file/f378584fb434.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0965; AD 2019-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-32-30
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-32-30

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2019-07-06](https://openairdocs.org/ad/2019-07-06.md), effective May 28, 2019: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-32-30/proposed.md).

## Text (17 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2018-0965; AD 2019-07-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/MODIFICATION - MAIN-GEAR RETRACTION ACTUATOR -
INSPECTION AND REPLACEMENT IF NECESSARY OF THE MLG SIDE BRACE
ACTUATOR SPLIT BALL BEARING
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 20003 to 20500
MANPOWER: PART A: 0.5 man−hour, PART B: Up to 8 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE YES NO
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts , please call Bombardier Aerospace Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 32−32
LANDING GEAR
Basic Issue: Dec 18/2017 100−32−30
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/MODIFICATION - MAIN-GEAR RETRACTION ACTUATOR -
INSPECTION AND REPLACEMENT IF NECESSARY OF THE MLG SIDE BRACE
ACTUATOR SPLIT BALL BEARING
1. PLANNING INFORMATION
NOTES:1 . Before you do this bulletin, examine all STC, STA or equivalent
action changes to make sure that this bulletin can be completed.
2. This Service Bulletin is covered by a dedicated schedule. Dedicated
schedules are used to reserve and manage inventory due to limited
availability of rotable stock, parts and/or kits. Parts are limited, therefore,
advance part scheduling with our In−Service Implementation Team (ISIT)
is recommended prior to a maintenance visit. Please contact your
Regional Manager (RM), Field Service Representative (FSR) or Customer
Service Representative (CSR) to schedule your aircraft as there is a
limited availability. The parts will be allocated on a first come first serve
basis.
For more information on dedicated schedules, refer to SB 100−00−02.
3. A completed Certificate of Scrap, for the removed split ball bearing, Part
No. 104467672, must be submitted within six weeks of the incorporation of
this Service Bulletin to Triumph Actuation Systems − Yakima.
Send a scanned copy of the completed Certificate of Scrap by e−mail to:
JLRoybal@triumphgroup.com and RFarabee@triumphgroup.com, and
make sure to include the Part Number and the Serial Number of the top
assembly in the subject line of the e−mail.
If the Certificate of Scrap is not received within six weeks of the
incorporation of this Service Bulletin, the operator will be charged, by
Triumph Actuation Systems − Yakima, for the replacement split ball
bearing.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 32−32
LANDING GEAR
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2017 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Dec 18/2017 100−32−30
Page 1 of 14
This Service Bulletin is available at:

### Page 3

A. Effectivity
BD−100−1A10 aircraft, Serial No. 20003 to 20500.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aerospace Service Bulletin(s).
B. Reason
Bombardier Aerospace was informed by its supplier that some MLG side stay
actuators were supplied with a non conforming split ball bearing, Part
No.104467672. Material properties of the non conforming split ball bearings do not
meet the requirements of AMS4640H.
This Service Bulletin introduces a Special Check/Modification, that gives
instructions to verify the serial number of both side stay actuators installed on the
aircraft, and replace any non conforming split ball bearing if necessary. The
replacement of the discrepant split ball bearings will greatly reduce the risk of
bearing seizure. The benefits to the customer are improved reliability and reduced
maintenance costs.
C. Description
This Service Bulletin gives instructions in PART A to:
− Verify the serial number of the LEFT and RIGHT side brace actuator, and
− Take the appropriate action.
This Service Bulletin gives instructions in PART B to:
− Remove the existing discrepant split ball bearing,
− Install a new split ball bearing, and
− Do the necessary tests to make sure the system operates correctly.
D. Compliance
Recommended at or before 3750 flight cycles (since new) or within 48 months from
Service Bulletin release date (Basic Issue), whichever comes first.
NOTES: 1. For units with more than 3350 flight cycles (since new) at the time of
Service Bulletin release date (Basic Issue), comply within 12 months
or 400 flight cycles, whichever comes first.
2. If it is not possible to complete all the instructions in this Service
Bulletin because of the configuration of the aircraft, submit an SRPSA
for analysis and to get an approved disposition to complete this
Service Bulletin.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 2 of 14

### Page 4

E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to SB
100−00−02.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
0.5 man−hour is necessary to do PART A of this Special Check/Modification.
Bombardier Aerospace does not pay for the labor to do PART A of this Special
Check/Modification.
Up to 8 man−hours are necessary to do PART B of this Special Check/Modification
and are divided as follows:
− 2.5 man−hours per side,
− 2 man−hours for the testing, and
− 1 man−hour for the Close−Out.
The labor required to do PART B of this Special Check/Modification is at no cost if:
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled at or before 3750 flight cycles (since new) or
within 48 months from Service Bulletin release date (Basic Issue), whichever
comes first.
NOTE: For units with more than 3350 flight cycles (since new) at the time of
Service Bulletin release date (Basic Issue), schedule within 12 months or
400 flight cycles, whichever comes first.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 3 of 14

### Page 5

G. Material − Cost and Availability
No kit is necessary to do PART B of this. For material data, refer to Paragraph 3.
For the part necessary to do PART B of this Special Check/Modification, refer to
Paragraph 3.B.
The part is available at no cost if:
− a no−charge purchase order is sent to Bombardier Aerospace in less than 48
months from this Service Bulletin release date (Basic Issue).
NOTE: For units with more than 3350 flight cycles (since new) at the time of
Service Bulletin release date (Basic Issue), purchase order must be sent
within 12 months from this Service Bulletin release date (Basic Issue).
This Service Bulletin is covered by a dedicated schedule. Dedicated schedules are
used to reserve and manage inventory due to limited availability of rotable stock,
parts and/or kits. Parts are limited, therefore, advance part scheduling with our
In−Service Implementation Team (ISIT) is recommended prior to a maintenance
visit. Please contact your Regional Manager (RM), Field Service Representative
(FSR) or Customer Service Representative (CSR) to schedule your aircraft as there
is a limited availability. The parts will be allocated on a first come first serve basis.
For more information on dedicated schedules, refer to SB 100−00−02.
A completed Certificate of Scrap, for the removed split ball bearing, Part No.
104467672, must be submitted within six weeks of the incorporation of this Service
Bulletin to Triumph Actuation Systems − Yakima.
Send a scanned copy of the completed Certificate of Scrap by e−mail to:
JLRoybal@triumphgroup.com and RFarabee@triumphgroup.com Make sure to
include the Part Number and the Serial Number of the top assembly in the subject
line of the e−mail.
If the Certificate of Scrap is not received within six weeks of the incorporation of this
Service Bulletin, the operator will be charged, by Triumph Actuation Systems −
Yakima, for the replacement split ball bearing.
For all parts transactions, Bombardier Aerospace’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
During or after the above free period, Smart Parts Plus does not pay for the parts.
H. Tooling
The equipment and tools listed below are necessary to do this Special
Check/Modification:
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 4 of 14

### Page 6

GSE REFERENCE NO. PART NO. DESCRIPTION
07−10−01 − Pad, Jacking
07−10−02 − Jack, Tripod Wing
07−10−03 − Jack, Forward Fuse
07C−10−04 − Axle Jack, MLG/NLG
07C−10−06 − Support, Rear Fuselage
10−10−10 − Wheel Chocks, Rubber
12−20−03 − Strut Servicing Kit(Air/Nitrogen)
12−30−01 − Nitrogen Charging Adapter
24−00−24 S4933959−501 Tag, Circuit Breaker
29C−00−01 Hydraulic Power Unit
Commercially Available −
Gauge Digital, Nitrogen
Pressure 938 to 3943−psi
(6467 to 27186−kPa)
Commercially Available − Wrench, Torque
Refer to the Standard Practices Manual (SPM), Wiring Manual (WM), Chapter 20,
and the table that follows for the tools applicable to the wiring modification:
NOTES: 1. Refer to the CH 300 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for acceptable GSE
equivalents.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aerospace, Restriction and/or Special Instruction (RSI),
C−100−000−32−0168, Rev. −−2.
− Bombardier Aerospace, Standard Practices Manual (SPM), Chapter 20.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 5 of 14

### Page 7

− Bombardier Aerospace, SB 100−00−02, Service Bulletin Description and Policy.
− Safran Landing Systems, Service Bulletin SB100−32−024.
− Triumph Actuation Systems − Yakima, Service Bulletin 40310−32−2.
− Triumph Actuation Systems − Yakima, Certificate of Scrap (attached).
− CH 300 Aircraft Maintenance Manual (AMM), Chapters 6, 7, 24, 29 and 32.
− CH 300 Illustrated Tool and Equipment Manual (ITEM), Chapters 7, 10 and 24.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
For the Challenger 350, refer to Service Bulletin 350−32−006.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTE: All references made to zones, access panels and/or doors, are from the
CH 300 AMM, Chapter 6.
A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all hydraulic safety precautions. Refer to AMM 29−00−00−910−801.
(3) Obey all hydraulic technical precautions. Refer to AMM 29−00−00−910−802.
(4) Obey all landing−gear safety precautions. Refer to AMM 32−00−00−910−801.
(5) Release the hydraulic pressure from the left and right hydraulic systems. Refer
to AMM 29−10−00−862−802.
(6) Open and tag the circuit breakers that follow:
CB PANEL CB NO. NAME ZONE
LCBP C13 WOW A/RET/EXT 211
LCBP C14 WOW B 211
RCBP C13 WOW B/RET 212
RCBP C14 WOW A/RET 212
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 6 of 14

### Page 8

B. PART A − Special Check
(1) Examine the serial number of the LEFT and RIGHT MLG side brace actuator
assembly, Part No. 40310−103, for applicability.
(2) If the serial number is not listed in Table 1, no further action is required.
(3) If the serial number is listed in Table 1, continue to Paragraph 2.C.
TABLE 1 - IMPACTED SERIAL NO.
0097, 0170, 0220, 0281, 0283, 0306, 0310, 0363, 0386, 0410, 0468, 0530,
0865, 0961 to 0963, 0966 and 0969
C. PART B− Modification − Replacement of the Split Ball Bearing
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Lift the complete aircraft with jacks. Refer to AMM 07−10−01−582−801.
(2) Release the nitrogen pressure from the MLG strut and compress it enough to
facilitate the removal and installation of the side brace pin assembly (11).
(3) Replace the split ball bearing as follows, refer to Figure 1:
(a) Remove and discard the cotter pin (1). Refer to
SPM−MM 20−50−00−000−802.
(b) Remove and discard the nut (2).
(c) Remove and discard the washer (3).
(d) Move the bell crank (4) away from the side brace pin assembly (11).
(e) Remove and discard the countersunk washer (5).
(f) Remove and discard the tab lock washer (7) and the nut (6). Refer to
SPM−MM 20−50−00−000−803.
NOTE: If installed, remove the lockwire between the nut (6) and the lock
plate (8). Refer to SPM−MM 20−50−00−000−801.
(g) Support the MLG side brace actuator (10), per best shop practices.
(h) Remove the side brace pin assembly (11).
(i) Remove the split ball bearing (9) from the side brace actuator rod end
assembly and scrap.
NOTE: Make sure you fill and submit the Certificat of Scrap. Refer to
Paragraph 1.G.
(j) Install new split ball bearing, Part No. 104467672 (9) in the side brace
actuator rod end assembly. Make sure that the witness marks on the
bearing faces are matched together.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 7 of 14

### Page 9

(k) Apply a layer of grease on the side brace pin assembly (11).
(l) Install the side brace pin assembly (11) through the side brace actuator
(10) and the main fitting (12).
NOTE: Make sure the flat area on the side brace pin assembly (11) is
aligned with the flat area in the lock plate (8).
(m) Install the new tab washer, Part No. 32228−1 (7).
NOTE: Make sure the tab is in the slot in the lock plate.
(n) Install the new nut, Part No. NAS509−18 (6).
(o) Tighten the new nut (6) by hand, and make sure the flat area on the side
brace pin assembly (11) is aligned with the flat area in the lock plate (8).
Make sure the tab on the tab washer (7) stays in the slot in the lock plate
(8).
(p) Hold the head of the side brace pin assembly (11) in position to prevent
rotation and forward −and−aft movement.
(q) Torque the new nut (6) from 83.34 to 100 lb ft (113 to 135.58 Nm). Refer
to SPM−MM 20−21−00−910−801.
NOTE: Make sure that the tab washer (7) did not turn when you applied
the torque.
(r) Bend the tabs of the tab washer (7) on the nut (6). Refer to
SPM−MM 20−50−00−400−803.
(s) If previously removed, install lockwire between the nut (6) and the lock
plate (8). Refer to SPM20−50−00−400−801.
(t) Install the new countersunk washer, Part No. MS20002C12 (5) on the side
brace pin assembly (11).
(u) Move the bell crank (4) back in position on the side brace pin
assembly (11).
(v) Install the new washer, Part No. NAS1149E0963P (3).
(w) Install the new nut, Part No. MS14145L9 (2).
(x) Torque the nut (2) from 60 to 100 lb in (6.78 to 11.30 Nm). Refer to
SPM−MM 20−21−00−910−801.
(y) Install the new cotter pin, Part No. MS24665−304 (1). Refer to
SPM−MM 20−50−00−400−802.
(4) Lubricate the spherical bearing and the bell crank. Refer to AMM 
12−22−00−640−802.
(5) Identify the reworked Side Stay Actuator with the Service Bulletin identifier
number (40310−32−2) with permanent ink per best shop practices. Refer to
Figure 2.
(6) Apply one coat of polyurethane clear coat over the ink marking per best shop
practices. Refer to Figure 2.
(7) Do the Servicing of the MLG Shock−Strut with Nitrogen Only. Refer to
AMM 12−17−00−614−803.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 8 of 14

### Page 10

D. Testing
(1) Remove the tags and close the circuit breakers that follows:
CB PANEL CB NO. NAME ZONE
LCBP C13 WOW A/RET/EXT 211
LCBP C14 WOW B 211
RCBP C13 WOW B/RET 212
RCBP C14 WOW A/RET 212
(2) Connect electrical power to the aircraft. Refer to AMM 24−00−00−861−801.
(3) Make sure that the landing−gear control handle is in the DOWN position.
(4) Set the throttle levers to the CLB position.
(5) Install aluminum tape on the radio altimeter receiver antenna.
(6) Make sure that the flaps are not at the 30 degree position. Refer to
AMM 27−52−00−610−801.
(7) Make sure that the indication on the primary page of the engine indication and
crew alerting system (EICAS) shows DN (Green).
(8) Remove the lockpin from the nose−landing−gear (NLG). Refer to
AMM 10−11−00−941−801.
(9) Remove the lockpins from the main−landing−gear (MLG). Refer to AMM 
10−11−00−941−803.
WARNING: MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE NOT
NEAR THE LANDING GEAR. EXTENSION/RETRACTION OF THE
LANDING GEAR CAN CAUSE INJURY TO PERSONS AND
DAMAGE TO THE EQUIPMENT.
(10) Pressurize the Left and Right Hydraulic Systems. Refer to
AMM 29−10−00−862−801.
(11) Do three retraction/extension cycles.
NOTE: Make sure that all the parts move freely.
(12) On the EICAS primary page, make sure that the message that follows is not
shown:
EICAS NMESSAGE LEVEL (COLOR)
GEAR DISAGREE Caution (amber)
(13) Do one landing−gear emergency−extension cycle as follows:
(a) Move the landing−gear control−handle to the UP position.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 9 of 14

### Page 11

(b) When the landing gear is up and locked, make sure that the gear
indication on the EICAS primary page shows UP (white).
(c) Release pressure from the Right hydraulic systems. Refer to
AMM 29−10−00−862−802.
(d) Pull the landing−gear manual−release handle until the landing gears
extend.
(e) Make sure that the NLG and MLG extend smoothly.
(f) Move the landing−gear control−handle to the DOWN position.
(g) Stow the landing−gear manual−release handle.
(14) Pressurize the Left and Right Hydraulic Systems. Refer to
AMM 29−10−00−862−801.
(15) Do a final retraction/extension cycle.
(16) Release hydraulic pressure from the Left and Right hydraulic systems. Refer to
AMM 29−10−00−862−802.
(17) Install the lockpin in the NLG, and make sure that it goes in freely. Refer to
AMM  10−11−00−941−802.
(18) Install the lockpins in the MLG, and make sure that it goes in freely. Refer to
AMM 10−11−00−941−804.
(19) Remove the electrical power from the aircraft. Refer to
AMM 24−00−00−861−802.
E. Close−out
NOTE: The steps in the Close−out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Lower the complete aircraft. Refer to AMM 07−10−01−586−801.
F. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
In an effort to improve the quality of our technical communications, we are
requesting your feedback. Please take a moment to fill out our easy on−line Service
Bulletin survey:
http://csefeedback.aero.bombardier.com
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 10 of 14

### Page 12

3. MATERIAL INFORMATION
A. Kits
No kit required.
B. Parts
The part that follows is necessary to do this Service Bulletin and is available from
Bombardier Aerospace Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PARTNO. INSTRUCTIONS- DISPOSITION
DMK378−101 Up to2 Kit, MessierDowty − −
NOTE: The part number for the item listed above is subject to change without
revision to this Service Bulletin. In case of discrepancy between this list
and any other list, the Illustrated Parts Catalog prevails and shall be used
to determine the latest part number.
C. Material
The material that follows, or equivalent, is necessary to do this Service Bulletin. It
can be purchased from a local supplier. Bombardier Aerospace does not pay for
this consumable.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Clear Coat,
Polyurethane
CT: 4 hours
PF−6
Series/PH36
or
PG−6 Series
− As Necessary Code: A
Grease,
Aircraft and
Instrument,
Gear and
Actuator
Screw
Aeroshell 33 MIL−PRF−23827CType I As Necessary Code: B
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 11 of 14

### Page 13

DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY
SUPPLIER
(SEE
NOTE)
Tape,
Aluminum No. 425 − As Necessary Code: C
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
SUPPLIERS ADDRESSES BY CODES
Code: A
Axon Hentzen Aerospace
307 Echelon Road,
Greenville, SC 29605–5234
U.S.A.
Tel.: 416−746−2233
www.hentzel.com
Code: B
Shell Canada Limited
400 4th Avenue S.W.
Calgary, Alberta
Canada, T2P 0J4
Tel.: 1−877−656−3111
www.shell.ca
Code: C
3M Co.
Building 304−1−01
St−Paul, MN
55144−1000
U.S.A.
Tel.: 651−737−6501
Tel: 800−364−3577
www.3m.com
D. Publications
No publications required.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Dec 18/2017 100−32−30
Page 12 of 14

### Page 14

CSB3232_012
A 
A
11
10
9
12
8
7
6 5
4
3
2
1
MODEL BD−100−1A10 (CH−300)
Split Ball Bearing Replacement
FIGURE 1
Basic Issue: Dec 18/2017 100−32−30
Page 13 of 14

### Page 15

CSB3232_010
SIDE BRACE ACTUATOR
M−B−DT P/N
TAS−Y P/N
INSP.
SER. NO.
40300−
40310−
DATE
DESIGNED AND MANUFACTURED BY
TRIUMPH ACTUATION − YAKIMA
FSCM 97415
40310−32−2
CYLINDER ASSEMBLY
IDENTIFICATION PLATE (4−180B)
POLYURETHANE
COATINGINK MARKING
Messier−Bugatti−Dowty
YAKIMA, WA USA
PHOSPHATE ESTER FLUID PER AS1241 ONLY
MODEL BD−100−1A10 (CH−300)
Ink Marking Detail
FIGURE 2
Basic Issue: Dec 18/2017 100−32−30
Page 14 of 14

### Page 16

100−32−30 Basic Dec 18/2017
SPECIAL CHECK/MODIFICATION − MAIN−GEAR RETRACTION
ACTUATOR − INSPECTION AND REPLACEMENT IF NECESSARY OF
THE MLG SIDE BRACE ACTUATOR SPLIT BALL BEARING
In an effort to improve the quality of our technical communications, we are replacing the
standard Service Bulletin Evaluation Form with an on−line Service Bulletin Survey
and we are requesting your feedback. Please take a moment to fill out our easy on−line
Service Bulletin survey at:
http://csefeedback.aero.bombardier.com
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:

### Page 17

SERVICE BULLETIN INCORPORATION SHEET − "100−32−30"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If your aircraft is registered on CAMP and you are reporting to them,
please do not send the incorporation sheet to Bombardier. If your aircraft
is on another tracking system, please contact Bombardier to make
arrangements for automated data submission.
100−32−30 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
