# Bombardier Service Bulletin 100-32-36

Copy: No revision named ("100-32-36"), 9 pages: PDF https://openairdocs.org/files/sha256/9a/0a/9a0a8f0d800950fccffa3df45c90d2d3da86a08a8830a55d5755c2d965e55a91; text https://openairdocs.org/service-documents/bombardier/sb-100-32-36/file/9a0a8f0d8009.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0658; AD 2021-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 100-32-36
- Page: https://openairdocs.org/service-documents/bombardier/sb-100-32-36

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2021-25-07](https://openairdocs.org/ad/2021-25-07.md), effective Feb 15, 2022: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-100-32-36/proposed.md).

## Text (9 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2021-0658; AD 2021-25-07 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND
INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
At operator’s earliest
convenience (See Paragraph
1.D. for details)
EFFECTIVITY: A/C Serial No. 20001, 20003 to 20500
MANPOWER: Refer to Paragraph 1.F
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS NOYES
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: N/A
NOTE: This Service Bulletin may be subject to an Airworthiness Directive (AD) which will
make it necessary to implement this Service Bulletin.
To place an order for parts or kits, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 32−00
LANDING GEAR
Basic Issue: Jun 25/2020 100−32−36
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND
INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. AMM 32 −32−07−400−801 Revision 67 dated Jan 15/2020 is a prerequisite
and must be incorporated into the AMM before doing inspection of
lockwire to check the requirement for installation of lockwire at LH and RH
main landing gear side brace actuator assembly nut interface.
A. Effectivity
BD−100−1A10 aircraft, Serial No. 20001, 20003 to 20500.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
Objective/Benefit:
This Service Bulletin introduces a special check for the lockwire installation to the
nut located at the interface with the LH and RH pin assembly of the main landing
gear side brace actuator assembly. Addition of the lockwire as a secondary
retention to the side brace actuator pin and nut improves the reliability.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−300)
ATA 32−00
LANDING GEAR
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
© 2020 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Jun 25/2020 100−32−36
Page 1 of 6
This Service Bulletin is available at:

### Page 3

C. Description
This Service Bulletin gives instructions to:
− Inspect the LH and RH main landing gear side brace actuator assembly nut for
lockwire, and if necessary install new lockwire.
D. Compliance
Recommended within 5 years from this Service Bulletin release date (Basic Issue).
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
F. Manpower
NOTES: 1. The man −hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 100−00−02.
2. This Service Bulletin may require consumable materials that have
specific curing times (refer to Paragraph 3). The accumulated curing
time is not included in the man−hours and should be considered for
planning purposes before you schedule this Service Bulletin.
1 man−hour is necessary to do this Service Bulletin.
Bombardier Aerospace does not pay for the labor to do special check/modification.
G. Material − Cost and Availability
No kit or parts are necessary to do this special check/modification. For material
data refer to Paragraph 3.C.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Jun 25/2020 100−32−36
Page 2 of 6

### Page 4

H. Tooling
The equipment and tool listed below is necessary to this special check/modification.
GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available − Glasses, Safety
NOTES: 1. Refer to the BD −100 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM BD −100, for acceptable
GSE equivalents.
3. This list is provided for quick reference. In case of discrepancy
between this list and the tools called in the SPM, WM, Chapter 20,
then the tools called in the SPM, WM prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− Bombardier Aviation, Restriction and/or Special Instruction (RSI),
C−100−000−32−0173, Rev. −−.
− Bombardier Aviation, Modification Summary, 100T505391, Rev. B−1.
− Bombardier Aviation, Standard Practices Manual (SPM), Chapter 20.
− CH 300 Aircraft Maintenance Manual (AMM), Chapters 6, 10 and 32.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
− For the Challenger 350 aircraft, use Service Bulletin 350−32−012.
2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the BD −100,
Aircraft Maintenance Manual unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
BD−100, Aircraft Maintenance Manual, Chapter 6.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Jun 25/2020 100−32−36
Page 3 of 6

### Page 5

A. Aircraft Setup
NOTE: The steps in the Aircraft Setup section of this Service Bulletin are
recommended steps. The steps give a recommendation to get access to
the work area. This recommendation is to give a safe work area and to
minimize possible damage to surrounding aircraft parts. Alternative steps
can be used at the operator’s discretion.
(1) Obey all landing −gear safety precautions. Refer to AMM 32−00−00−910−801.
(2) Install the lockpins in the main landing gear. Refer to
AMM 10−11−00−941−804.
B. Special Check − Inspection of the Lockwire
NOTE: AMM 32 −32−07−400−801 Revision 67 dated Jan 15/2020 is a prerequisite
and must be incorporated into the AMM before doing inspection of
lockwire to check the requirement for installation of lockwire at LH and RH
main landing gear side brace actuator assembly nut interface.
(1) Get access to the LH and/or RH main landing gear.
(2) Visually inspect the LH and RH main landing gear side brace actuator
assembly nut interface with pin, Part No. 40245−105 or 40254−106 for the
lockwire, Part No. MS20995C20 or MS20995C32.
(a) If lockwire, Part No. MS20995C20 or MS20995C32 is installed on the nut,
Part No. NAS509−18 of the side brace actuator assembly, Part No.
40310−103 or 40310−107, go to Paragraph 2.D.
(b) If lockwire, Part No. MS20995C20 or MS20995C32 is not installed on the
nut, Part No. NAS509−18 of the side brace actuator assembly, Part No.
40310−103 or 40310−107, go to Paragraph 2.C.
C. Modification − Installation of the Lockwire to the Nut
NOTE: If it is not possible to complete all the instructions of this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Install the lockwire, Part No. MS20995C20 or MS20995C32 on the nut, Part
No. NAS509−18 of the side brace actuator assembly, Part No. 40310−103 or
40310−107. Refer to SPM−MM 20−50−00−400−801.
D. Close −out
NOTE: The steps in the Close −out section of this Service Bulletin, except for the
return−to−service tests, are recommended steps. The steps give a
recommendation to install components removed during the Aircraft Setup.
This recommendation is to make sure that the aircraft is safe and ready to
return to service. Alternative steps can be used at the operator’s
discretion.
Remove all tools, equipment and unwanted materials from the aircraft.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Jun 25/2020 100−32−36
Page 4 of 6

### Page 6

E. Recording
When this Service Bulletin is completed, make an entry in the aircraft log and send
the attached Incorporation Notice to Bombardier Business Aircraft Customer
Services (BBACS).
For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
No parts required.
C. Material
The material that follows is necessary to do this Service Bulletin. It can be
purchased from a local supplier. Bombardier Aviation does not pay for this
consumable.
DESCRIPTION PARTNO./NAME SPECIFICATION QUANTITY SUPPLIER(SEENOTE)
Lockwire
MS20995C20
or
MS20995C32
− As Necessary Code: A
NOTES: 1. Refer to the table that follows for each suppliers address listed by
codes.
2. The Curing Time (CT), if applicable, for each consumable material is
indicated with the description of each product.
3. At time of release of this Service Bulletin, the information on the
supplier was valid and accurate. In the event that this information has
changed, the operator is encouraged to use the World Wide Web to
find a local supplier.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Jun 25/2020 100−32−36
Page 5 of 6

### Page 7

SUPPLIERS ADDRESSES BY CODES
Code: A
Commercially Available
D. Publications
No publications required.
MODEL BD−100−1A10 (CH−300)
Basic Issue: Jun 25/2020 100−32−36
Page 6 of 6

### Page 8

100−32−36 Basic Jun 25/2020
SPECIAL CHECK/MODIFICATION – LANDING GEAR – INSPECTION AND
INSTALLATION OF LOCKWIRE TO SIDE BRACE ACTUATOR NUT
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 9

SERVICE BULLETIN INCORPORATION SHEET − "100−32−36"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
100−32−36 Basic
COMPLIED WITH
YES    NO    N/A
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
