# Bombardier Service Bulletin 215-4423

Copy: Revision 5 ("SB 215-4423 Rev 5"), 44 pages: PDF https://openairdocs.org/files/sha256/8c/54/8c54c788923262f3b37c5c4c7f38e7772ae15ec3d614c0e0998ac68651c46e05; text https://openairdocs.org/service-documents/bombardier/sb-215-4423/file/8c54c7889232.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2017-0474; AD 2017-17-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 215-4423
- Latest revision known: 215-4423, Revision 5, dated March 17, 2016 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-215-4423

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2017-17-17](https://openairdocs.org/ad/2017-17-17.md), effective Oct 11, 2017: Revisions 1, 2, 3, 4, 5 and NC

## Text (44 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2017-0474; AD 2017-17-17 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

the evolution of mobility
Service Bulletin 215-4423March 17/16
ATA Ref: 27−20Page 1 of 1
MODEL CL-215-6B11 (415)
REVISION TRANSMITTAL SHEET
SERVICE BULLETIN
215−4423
FLIGHT CONTROLS
RELOCATION OF THE FLIGHT CONTROL HYDRAULIC ACCUMULATORS
Service Bulletin No.: 215 −4423 Date of Original Issue: April 4/11
Revision No.: 5 Date of Issue: March 17/16
NOTES: 1. FOR RETROACTIVE ACTION APPLICABLE TO AIRCRAFT
ALREADY MODIFIED IN ACCORDANCE WITH THE ORIGINAL
ISSUE OF THIS SERVICE BULLETIN, REFER TO THE BOX ON
PAGE1 OF THIS SERVICE BULLETIN.
2. This revision supersedes the previous issue of this Service Bulletin.
3. Black bars in the left margin of this Service Bulletin and the details on
this Revision Transmittal Sheet refer to changes made since the
previous issue.
This Revision is issued to:
1. Clarify various data and instructions in PART G − REWORK INSTALLATION (HARDWARE
REPLACEMENT) USING KIT NO. 215K4423E.

### Page 2

the evolution of mobility
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 1 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
MODEL CL-215-6B11 (415)
SERVICE BULLETIN
215−4423
FLIGHT CONTROLS
RELOCATION OF THE FLIGHT CONTROL HYDRAULIC ACCUMULATORS
1. Planning Information
THE FOLLOWING POTENTIAL REWORK ACTION IS RECOMMENDED FOR AIRCRAFT
ALREADY MODIFIED IN ACCORDANCE WITH REVISIONS NC, 1, 2, or 3 OF THIS SERVICE
BULLETIN:
1. Incorporate PART F of this Service Bulletin that installs the Rework Kit No. 215K4423D.
  This action is recommended for aircraft which have installed the Kit No. 215K4423A
  (K215T75051−4 Installation).
2. Incorporate Part G of this Service Bulletin that installs the Rework Kit No. 215K4423E.
  This action is recommended for aircraft having installed Kits No. 215K4423 (Basic) and
  the 215K4423B (K215T75013−2 Rework Installation).
A. Compliance
Installation of this Service Bulletin is recommended.
It should be incorporated before June 1st, 2015.
NOTE: This Service Bulletin is applicable only to aircraft in the condition as originally
delivered by Canadair and/or Bombardier Aerospace or as subsequently modified by
Canadair and/or Bombardier Aerospace Service Bulletin(s).  Prior to incorporation of
this Service Bulletin, the status of any related systems or structural modification(s)
introduced by Supplementary Type Approval (STA) or equivalent action must be
examined for compatibility with the modifications and test procedures (if applicable)
detailed in this Service Bulletin.

### Page 3

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 2 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
B. Approval
The technical content of this Service Bulletin has been approved under the authority of the
Design Approval Organization No: DAO #93-Q-02.
C. Effectivity
CL-215-6B11 (415) turboprop aircraft Serial Nos. 2001 to 2081.
D. Reason
Several accumulator screw cap failures have been reported on the Bombardier CRJ-200
aircraft.  The Bombardier 415 aircraft uses similar hydraulic accumulators from the same
vendor.  A case study was performed on the Bombardier 415 to see what systems and/or
structures could be damaged if the screw cap on any one of the accumulators should fail and
what is the safety impact in relocating the three accumulators.
NOTE: No events of accumulator screw cap failures have been experienced on any
Amphibious aircraft (CL-215, CL-215T, or  Bombardier 415) models.
E. Description
This Service Bulletin gives instructions to remove, relocate, and reinstall the aileron, elevator,
and rudder hydraulic accumulators approximately 40 inches (1000 millimeters) aft and
outboard of their current location.  Several new hydraulic line assemblies, brackets and
supports are required to be installed with this relocation.  A new access panel is made in the
existing skin to access the accumulators for inspection and regular maintenance tasks.  The
Brake accumulator is not relocated as part of this Service Bulletin.
F. Manpower
We estimate that it will take 2 technicians approximately 27 hours (54 man hours total) to
complete this Service Bulletin.
G. Material Availability
IMPORTANT KIT ORDERING AND CONFIGURATION CONTROL INFORMATION
(1) Kit No. 215K4423 (Basic) (K215T75051−2 Installation)
This kit is no longer intended for first time installation and is no longer available.
If you have installed this kit, and if the 215K4423B Rework Kit has not been installed, you
will further require the rework Kit 215K4423D.
If you have installed this kit, and if the 215K4423B Rework Kit has also been installed,
you will further require the rework kit 215K4423E.
If you have received this kit, and have not yet installed it, you will require the addition of
the rework Kit 215K4423D to incorporate the equivalent of the 215K4423C Kit
(K215T75051−10 Installation).

### Page 4

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 3 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(2) Kit No. 215K4423A (K215T75051−4 Installation)
This kit is no longer intended for first time installation and is no longer available.
If you have this (either installed or in stock) kit, you will further require the rework Kit
215K4423D to incorporate the equivalent of the 215K4423C Kit (K215T75051−10
Installation).
(3) Kit No. 215K4423B (K215T75013−2 Installation Rework Kit )
This rework kit, originally used in conjunction with the 215K4423 (Basic) kit, is no longer
available and is not sufficient to modify those kits (installed or not installed) to 215K4423C
Kit (K215T75051−10 Installation) standard.
If you have a 215K4423B rework kit in stock and had need to install it − order a
215K4423E to use in conjunction.  This will be necessary in order to rework your aircraft
installation to the equivalent of he 215K4423C Kit (K215T75051−10 Installation) standard.
(4) Kit No. 215K4423C (K215T75051−10 Installation)
This Kit is intended standard for new installations of this Service Bulletin as of Revision 4.
(5) Kit No. 215K4423D (K215T75013−4 Installation Rework Kit )
This rework kit is intended for those aircraft that have installed the 215K4423A
(K215T75051−4 Installation) kit.  You will need this kit to rework your aircraft installation
to the equivalent of the 215K4423C Kit (K215T75051−10 Installation) standard.
(6) Kit No. 215K4423E (Select Item Rework Kit)
Kit No. 215K4423E is intended as a second rework kit for aircraft having installed Kits
No. 215K4423 (Basic) and 215K4423B (K215T75013−2 Rework Installation).
Where necessary, a No. 215K4423 (Basic) and 215K4423B in inventory (not installed)
may be combined with a 215K4423E kit to modify an aircraft to the equivalent of the
215K4423C Kit (K215T75051−10 Installation) standard.
All parts contained in the available kits are free of charge to operators of the Bombardier 415
aircraft.  Please contact your Specialized and Amphibious Aircraft Customer Service
Representative (CSR) to place a “No Charge” Purchase Order (PO) for this kit.
H. Tool Availability
No special tools or equipment are necessary.
I. Weight and Balance
As a result of this modification, the aircraft basic weight will increase by 3.5 pounds, and the
out-of-balance moment change will be + 2647.5 pound-inches.
J. Electrical Load Data
Not affected.

### Page 5

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 4 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
K. References
For Bombardier Aerospace Reference only:
(Not Supplied with Kit)
Bombardier Aerospace Modification Summary: 415-79046, Revision B −3
415-79393, Revision A−1
415-79464, Revision B−1
415-79614, Revision B−1
415-79823, Revision C
415-79982, Revision B
Bombardier Aerospace Restriction and/or Special Instruction (RSI) C-3839, Revision, D.
Bombardier Aerospace Kit Drawing: K215T75051, Revision L.
K215T75013, Revision C
L. Publications Affected
PSP 492, Maintenance Manual, Chapter 27-12-00, 27-22-00, and 27-32-00
PSP 494, Illustrated Parts Catalogue, Chapter 27-12-00, 27-22-00, and 27-32-00.
M. Related Service Bulletin
None.
2. Accomplishment Instructions
NOTES: 1. For this modification, it is assumed that standard maintenance and repair practices
will be applied in accordance with applicable Product Support Publications (PSP).
2. For parts location, refer to the illustrations in this Service Bulletin.
3. When drilling new fastener holes, maintain a 2.0 inch fastener diameter edge distance
and an interpitch distance of 4.0 inch fastener head diameter unless otherwise
specified.
4. Bare metal areas must be treated with anodizing solution, MIL-C-5541 Class 1A, and
two coats of fluid resistant epoxy primer, BAMS 565-001.  Apply finishing topcoat,
BAMS 565-002, as required.  Refer to PSP 497, Chapter 51-71-02, CORROSION
PREVENTIVE TREATMENT − GENERAL PROCEDURES.
5. Install all parts with faying surface sealant, MIL-S-81733 Type 4.  Apply beading
sealant, MIL-S-81733 Type 2, as required to prevent water ingress.  Refer to
PSP 497, Chapter 51-23-01, SEALING − GENERAL PROCEDURES.

### Page 6

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 5 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
6. To help with the installation, mark all the individual pieces with location and item
numbers.
7. For specific and other general installation instructions, refer to the FLAG NOTES
(numbers in triangles) and the GENERAL NOTES on Sheets 4 and 5 of the Kit
Drawing Parts List.
8. This Service Bulletin describes the sequence that the structures are fitted on the
aircraft.  First, all the structures are fitted and secured with cleco pins.  Second, all the
structures are removed and subsequently riveted in place.
9. The instructions in this Service Bulletin do not call rivets or fasteners to be used.
Upon final installation of a part, refer to the detailed views on the Kit Drawings for
fastener call outs.
10.Take special note of all LZ and BB (countersink) rivet locations.  Mark their locations
on the aircraft interior/exterior skins for easy reference.
11. Take special note of all the rivet locations accompanied by a flag note.  Mark their
locations on the aircraft interior/exterior skins for proper rivet installation.
12.Upon final installation, install all items and rivets with faying surface sealant and/or
aerodynamic sealant as noted on the Kit Drawings.
13.In this Service Bulletin, the term “cleco pin” refers to a type of sheet metal fastener.  If
your organization does not utilize cleco pins, then use a similar replacement.
14.During structure fitting, use a #40 drill bit (3/32 or 0.098 inch) to drill all pilot holes.
For final installation, refer to the Kit Drawing for fastener size and drill full size
accordingly.
15.If any deviation exists, contact your Amphibious Aircraft Technical Representative for
further instructions.
16.For information regarding electrical bonding, refer to the PSP 492, Aircraft
Maintenance Manual, Chapter 51−80−00 ELECTRICAL BONDING − MAINTENANCE
PRACTICES.

### Page 7

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 6 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
A. PART A − PARTS REMOVAL
Refer to the illustrations in Figure 1.
WARNING: MAKE SURE THAT PERSONNEL AND EQUIPMENT ARE A SAFE DISTANCE
AWAY FROM ALL HYDRAULICALLY OPERATED SYSTEMS BEFORE YOU
REMOVE THE ELECTRICAL POWER.  IF YOU DO NOT DO THIS, INJURIES
TO PERSONNEL AND DAMAGE TO EQUIPMENT CAN OCCUR.
(1) Remove the electrical power.  Refer to PSP 492, Maintenance Manual, Chapter 24-00-00,
ELECTRICAL POWER − MAINTENANCE PRACTICES.
WARNING: WEAR RUBBER GLOVES, EYE PROTECTION, AND A RESPIRATOR WHEN
HANDLING HYDRAULIC FLUID.  CONTACT WITH HYDRAULIC FLUID OR ITS
VAPOURS MAY CAUSE IRRITATION TO THE SKIN, THE EYES, AND THE
LUNGS.  FAILURE TO WEAR PROPER PROTECTION MAY CAUSE INJURIES
TO PERSONNEL.
(2) Release the aircraft hydraulic pressure.  Refer to PSP 492, Chapter 29 −00−00,
HYDRAULIC POWER − MAINTENANCE PRACTICES.
(3) Release the aircraft accumulator pressure.  Refer to PSP 492, Chapter 12-14-29,
REPLENISHING HYDRAULIC SYSTEM − SERVICING.
(4) Remove the two large access panels 255-1 and 255-2 from the top of the aircraft.  Refer
to PSP 492, Chapter 6-44-00, WINGS, PYLONS, AND FLOATS − DESCRIPTION AND
OPERATION.
(5) Put an applicable container in position to collect hydraulic fluid if it spills when you
disconnect the hydraulic lines from the actuators.
(6) Refer to the DISPOSITION TABLE on Sheet 1, Zone 13 of the Kit drawing K215T75051
for a complete list of parts to be removed and re-installed or parts to be removed and
discarded/scrapped.
NOTE: The aircraft may have accumulator P/N MS28700 −3 or P/N 08 8423 010
installed.  All removal and relocation procedures will refer to the MS28700−3
accumulator as there is no physical difference between the two accumulators.
(a) Refer to PSP 494, Illustrated Parts Catalogue, Chapters 27-12-00, 27-22-00,
and 27-32-00 to help with locating parts to be removed.
(7) Remove and discard the aileron, elevator, and rudder hydraulic line assemblies as
follows:
(a) Disconnect the bonding jumper MS25083-5BB4 from the line assembly
215T75074-208 only (AFT side of aileron accumulator).  Discard the hardware.
(b) Disconnect the bonding jumper MS25083-5BB4 from the line assemblies
215T75074-208 and 215T75074-202.  Retain the bonding jumper and hardware.

### Page 8

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 7 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(c) Remove and retain the two fairleads 215T75103-2.
NOTE: The steps that follow may be accomplished at the technicians discretion.
Refer to kit drawing K215T75051, Sheet 2, View C-C.
1 Remove and discard the two support assemblies 215T75076-3 and
215T75076-4.
2 Plug the redundant holes in the aircraft structure with the rivets called.
(d) Remove and retain the three fairleads 215T75102-2 and the attaching hardware.
NOTE: These three fairleads will be re-worked and re-identified as K215T75051-8
(item 8) and then re-installed at the same location.
(e) Remove and discard the clamp MS21919WCG-4 that secures line assembly
215T75074-208.
(f) Disconnect line assembly 215T75074-208 from the AFT side of the aileron
accumulator MS28700-3.
1 Install protective closures, MIL−C−5501 or equivalent, on the open end of the
disconnected line (forward side of accumulator).
2 Remove bonding jumper as required to remove the line assembly
215T75074-208.
(g) Disconnect the other end of line assembly 215T75074-208 from line assembly
215T75074-202.  Discard the line assembly 215T75074-208 and union AN815-4J.
(h) Disconnect the other end of line assembly 215T75074-202 from the bulkhead union
AN823-4J (through aircraft ceiling).  Discard the line assembly 215T75074-202.
(i) Disconnect line assembly 215T75074-204 from the rudder accumulator and the
bulkhead union AN823-4J (through aircraft ceiling).  Discard the line assembly
215T75074-204.
(j) Disconnect line assembly 215T75074-206 from the elevator accumulator and the
bulkhead union AN823-4J (through aircraft ceiling).  Discard the line assembly
215T75074-206.
(k) Remove and discard line assembly 215T75074-10 connected to the rudder
accumulator MS28700-3.
(l) Remove and discard line assembly 215T75074-12 connected to the elevator
accumulator MS28700-3.

### Page 9

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 8 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(8) Remove and retain the aileron, elevator, and rudder hydraulic accumulators MS28700-3
as follows:
(a) Remove and retain the three (aileron, rudder, and elevator) accumulators from their
existing locations.
1 Remove and retain the reducers AN919-3J from the gas side of the three
accumulators.  Discard the packings.
2 Remove and retain the reducers AN919-10J and AN919-12J from the pressure
side of the three accumulators.  Discard the packings.
3 Install protective closures, MIL−C−5501 or equivalent, on the open ends of the
accumulators.
(b) Remove and retain the six bracket support clamps 215T75101-2.  Retain the
attaching hardware, and the six clamps 320−63P331−SH.
NOTE: On A/C Serial Nos. 2001 to 2015, the two aileron clamp P/Ns are
360-63-319-SH.
(c) Open the two holes in each clamp to the dimension indicated.

### Page 10

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 9 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − REMOVAL
FIGURE 1
LEGEND
REMOVE AND REINSTALL
REMOVE AND DISCARD (SCRAP)
REMOVE AND REWORK
215T75074−208
(LINE ASSY)
MS25083−5BB4
(BONDING JUMPER)
215T75102−2
(3 PLACES)
(FAIRLEAD)
215T75074−202
(LINE ASSY)
MS28700−3
(ACCUMULATOR)
215T75074−10
(LINE ASSY)
215T75074−202
(LINE ASSY)
AN815−4J
(UNION)
215T75074−208
(LINE ASSY)
MS21919WCG−4
(CLAMP)
215T75063−48
(EXISTING LINE
ASSY)
215T75101−2
(4 PLACES)
(BRACKET
CLAMP SUPPORT)
MS28778−5
(PACKING)
(2 PLACES)
MS28778−8
(PACKING)
(2 PLACES)
AN919−3J
(REDUCER)
(2 PLACES)
AN919−10J
(REDUCER)
(2 PLACES)
EFFECTIVITY
1
2
A/C 2001 TO 2015
A/C 2016 AND SUBS
360−63−319−SH
(4 PLACES)
320−62P331SH
(4 PLACES)
(CLAMP)
1
2

### Page 11

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 10 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − REMOVAL
FIGURE 1
MS28700−3
(AILERON ACCUMULATOR)
215T75101−2
(2 PLACES)
(BRACKET CLAMP SUPPORT)
AN919−3J
(REDUCER)
MS28778−5
(PACKING)
AN919−12J
(REDUCER)
MS28778−8
(PACKING)
LEGEND
REMOVE AND REINSTALL
REMOVE AND DISCARD (SCRAP)
360−63−319−SH
(2 PLACES)
320−62P331SH
(2 PLACES)
(CLAMP)
1
2
EFFECTIVITY
1
2
A/C 2001 TO 2015
A/C 2016 AND SUBS

### Page 12

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 11 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − REMOVAL
FIGURE 1
LEGEND
REMOVE AND REINSTALL
REMOVE AND DISCARD (SCRAP)
215T75074−204
(LINE ASSY)
215T75074−206
(LINE ASSY)
215T75074−12
(LINE ASSY)
MS28700−3
(ELEVATOR
ACCUMULATOR)
MS25083−5BB4
(BONDING
JUMPER)
MS25083−5BB5
(BONDING
JUMPER)
215T75074−202
(LINE ASSY)
MS28700−3
(RUDDER
ACCUMULATOR)
215T75076−4
(SUPPORT
 ASSY)
215T75076−3
(SUPPORT ASSY)
215T75103−2
(FAIRLEAD)
215T75103−2
(FAIRLEAD)

### Page 13

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 12 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
B. PART B − PARTS INSTALLATION / RELOCATION USING KIT NO. 215K4423 (BASIC)
THIS SECTION HAS BEEN SUPERSEDED
INSTALLATION INSTRUCTIONS FOR KIT NO. 215K4423 (BASIC), CONSISTING
OF THE THE K215T75051−2 INSTALLATION ARE DELETED.  
FIRST TIME INSTALLATION OF THIS SERVICE BULLETIN MUST BE DONE
USING KIT NO. 215K4423C, CONSISTING OF THE K215T75051−10
INSTALLATION.  REFER TO PARAGRAPH E.
FOR RETROACTIVE REWORK INSTRUCTIONS FOR AIRCRAFT WHICH HAVE
INSTALLED THE KIT NO. 215K4423 (BASIC), WITHOUT THE REWORK KIT
215K4423B, REFER TO PARAGRAPH F.
FOR RETROACTIVE REWORK INSTRUCTIONS FOR AIRCRAFT WHICH HAVE
INSTALLED THE KIT NO. 215K4423 (BASIC), WITH THE REWORK KIT
215K4423B, REFER TO PARAGRAPH G.
C. PART C − PARTS INSTALLATION / RELOCATION USING KIT NO. 215K4423A
THIS SECTION HAS BEEN SUPERSEDED
INSTALLATION INSTRUCTIONS FOR KIT NO. 215K4423A, CONSISTING OF THE
THE K215T75051−4 INSTALLATION ARE DELETED.  
FIRST TIME INSTALLATION OF THIS SERVICE BULLETIN MUST BE DONE
USING KIT NO. 215K4423C, CONSISTING OF THE K215T75051−10
INSTALLATION.  REFER TO PARAGRAPH G.
FOR RETROACTIVE REWORK INSTRUCTIONS FOR AIRCRAFT WHICH HAVE
INSTALLED THE KIT NO. 215K4423A, REFER TO PARAGRAPH F.

### Page 14

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 13 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
D. PART D − INSTALLATION OF REPLACEMENT HARDWARE USING REWORK KIT
NO. 215K4423B
THIS SECTION HAS BEEN SUPERSEDED
INSTALLATION INSTRUCTIONS FOR REWORK KIT NO. 215K4423B,
CONSISTING OF THE THE K215T75013−2 REWORK INSTALLATION ARE
DELETED.
THE STANDARD REWORK KIT TO BE USED, AS OF REVISION 4 OF THIS
SERVICE BULLETIN, IS THE KIT NO. 215K4423D, CONSISTING OF THE
K215T75013−4 REWORK INSTALLATION.  REFER TO PARAGRAPH F.
OPTIONS FOR AIRCRAFT PREVIOUSLY REWORKED WITH THIS KIT OR
FOR OPERATORS THAT HAVE ALREADY RECEIVED THIS KIT − BUT
HAVE NOT YET INSTALLED IT
IF THE KIT NO. 215K4423B WAS INSTALLED, THEN DO FURTHER REWORK
USING THE KIT NO. 215K4423E.  REFER TO PARAGRAPH G.
IF YOU HAVE A KIT NO. 215K4423B IN STOCK, AND YOU NEED TO REWORK
YOUR AIRCRAFT TO KIT NO. 215K4423C (K215T75051−10 INSTALLATION)
STANDARD, OBTAIN AND USE THE KIT NO. 215K4423E IN CONJUNCTION:
FOLLOW THE INSTRUCTIONS GIVEN IN PARAGRAPH F.

### Page 15

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 14 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
E. PART E − PARTS INSTALLATION / RELOCATION USING KIT NO. 215K4423C
The installation instructions of this paragraph (PART E) is intended to be the first-time
installation of this modification, as of Revision 4 of this Service Bulletin.
The parts used in the following instructions are drawn from the Kit No. 215K4423C.
If necessary, a combination of the contents of a Kit No. 215K4423 (Basic), a
Kit No. 215K4423B, and a Kit No. 215K4423D may be used to with the instructions of this
PART E to incorporate the equivalent of the Kit No. 215K4423C (K215T75051−10 Installation)
configuration.  If doing so, first combine and compare the kit inventories against the
Kit No. 215K4423C parts list.  Sort and substitute the superceded parts to create the
equivalent of the Kit No. 215K4423C.
NOTES: 1. All items are to be loose fitted until permanent location is determined.
2. All parts listed below without an “(item)” number are retained from the removal
section, PART A of this Service Bulletin.
3. Depending on the aircraft Serial Number, the aircraft may have accumulators
Part Numbers MS28700−3 or 08 8423 010 installed and there are no physical
differences between the two.  Further instructions given will refer only to the
MS28700−3 accumulator.
Refer to Figure 2 and Figure 3.
(1) Install the door panel assembly K215T75051-56 (item 56) as follows:
Refer to kit drawing K215T75051 Sheet 4, Detail A−A.
(a) Remove the sealant at FS 501.00 common to the access panel K215T75051-56
(item 56) installation.
(b) Remove the rivets in skin panel 215-30056 at FS 507.69 common to the access
panel K215T75051-56 (item 56) to obtain a flush surface to lay out the cut line for
the access panel K215T75051-56 (item 56).
(c) Position the door panel assembly K215T75051-56 (item 56) on the skin panel
215-30056 0.250 inch below FS 501.00 and in the centre of the two rows of rivets
between FS 501.00 and FS 514.36.  Mark a cut−out line around the access panel.
(d) Cut open the skin panel 215-30056 and the stringer at FS 507.69.
NOTE: There are no hydraulic line assemblies or electrical wires in this area.
(e) Remove the inboard, outboard, and the bottom row of rivets around the cut out.

### Page 16

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 15 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Refer to the various Sections, Views, and Notes on Sheet 4 and Figure 2 Detail C.
(f) Install the door panel assembly K215T75051-56 (item 56) support structure with the
parts that follows:
CAUTION: PAY SPECIAL ATTENTION DURING THE REMOVAL OF THE EXISTING
OUTBOARD BLIND RIVETS COMMON TO THE INSTALLATION OF ANGLE
215T75051-42 (ITEM 42).  DAMAGE TO THE WING SKIN COULD OCCUR.
REFER TO KIT DRAWING K215T75051, SHEET 4 VIEW AM-AM.
Quantity Description Part No. Item No.
1 Angle K215T75051-36 36
1 * Angle K215T75051-58 81
1 Bracket 215-30056-83 39
1 Angle K215T75051-42 42
1 Angle K215T75051-44 44
* For rivet call out on this Angle only, refer to kit drawing K215T75051, Sheet 5,  
  Section AD-AD.
(g) Install the 31 nutplates MS21059L3 (item 9) on the four angles K215T75051-36
(item 36), K215T75051-58 (item 81), K215T75051-42 (item 42), and
K215T75051-44 (item 44) as shown.
Refer to kit drawing K215T75051, Sheet 5, View AD-AD and DETAIL AE
(2) Refer to Sheet 5 and mark all stringers and Fuselage Stations (FS) on the aircraft ceiling
as necessary for quick reference.
Refer to Figure 2 Detail D.
(3) Mark the existing rivet locations on stringers L7 and L8 common to the footprint of the
accumulator mounting plate 215T75106-2 (item 4) and the angle 215T75051-50
(item 50).
CAUTION: DO NOT REMOVE THESE RIVETS FROM THE STRINGERS AT THIS
TIME.  REFER TO DETAILS AW AND AY.  THESE RIVETS SHOULD ONLY
BE REMOVED AFTER FINAL LOCATION OF THE ACCUMULATOR
MOUNTING PLATE 215T75106-2 (ITEM 4) HAS BEEN DETERMINED WITH
ALL SIX LINE ASSEMBLIES ATTACHED TO THE ACCUMULATORS WHEN
POSITIONED IN PLACE.  IT MAY BE NECESSARY TO MOVE THE
ACCUMULATOR MOUNTING PLATE FORWARD BY ONE RIVET
LOCATION TO PREVENT THE AILERON ACCUMULATOR FROM
FOULING ON THE STRUCTURE.
(4) Position the accumulator mounting plate 215T75106-2 (item 4) with the “Z” end of the
plate on stringer L8 just AFT of FS 501.00 as shown.

### Page 17

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 16 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(5) Use double sided tape to attach the two angles 215T75051-50 (item 50) on stringer L7
just AFT of FS 501.00 as shown.
(6) Install the fittings that follow on the elevator and rudder accumulators:
Pressure (Fluid) Side Item No. Gas Side Item No.
Reducer AN919-10J Retained Elbow AN939J5 29
Packing MS28778−8 A/R Union AN815-5J 34
Reducer AN919-3J Retained
Packing MS28778−5 A/R
(7) Install fittings that follow on the Pressure end of the aileron accumulator:
Pressure (Fluid) Side Item No. Gas Side Item No.
Reducer AN919-12J Retained Elbow AN939J5 29
Packing MS28778−8 A/R Union AN815-5J 34
Reducer AN919-3J Retained
Packing MS28778−5 A/R
(8) Secure each of the elevator and rudder accumulators MS28700-3 in the two bracket
support clamps 215T75101-2 with two clamps 320−62P331−SH.  Make sure the
accumulators are free to rotate in the clamps.
(9) Secure the aileron accumulator MS28700-3 in the two bracket support clamps
215T75101-2 with two clamps 320-62P331-SH.  Make sure the accumulator is free to
rotate in the clamps.  Refer to NOTE 38 for aircraft Serial Nos 2001 to 2015 to install two
new clamps 320-62P331SH (item 89) is required.
(10) Position the three accumulators on the mounting plate 215T75106-2 (item 4) as shown.
Refer to kit drawing K215T75051, Sheet 5, View AC-AC and DETAIL AE
(11) Install the new accumulator hydraulic line assemblies as follows:
WARNING: WEAR RUBBER GLOVES, EYE PROTECTION, AND A RESPIRATOR WHEN
HANDLING HYDRAULIC FLUID.  CONTACT WITH HYDRAULIC FLUID OR ITS
VAPOURS MAY CAUSE IRRITATION TO THE SKIN, THE EYES, AND THE
LUNGS.  FAILURE TO WEAR PROPER PROTECTION MAY CAUSE INJURIES
TO PERSONNEL.
(a) Use hydraulic fluid MIL-H-83282 to clean/flush the new line assemblies free of
contaminates prior to installation.
Refer to Figure 2 Detail A.
(b) Connect one end of line assembly 215T75074-270 (item 17) to the gas port of the
elevator accumulator and the other end to the bulkhead union AN823-4J (through
aircraft ceiling).

### Page 18

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 17 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(c) Connect one end of line assembly 215T75074-271 (item 18) to the gas port of the
rudder accumulator and the other end to the bulkhead union AN823-4J (through
aircraft ceiling).
(d) Connect one end of line assembly 215T75074-272 (item 19) to the gas port of the
aileron accumulator and the other end to the bulkhead union AN823-4J (through
aircraft ceiling).
NOTE: It maybe necessary to temporarily disconnect and reconnect some existing
hydraulic line assemblies to permit  installation of line assembly 215T75074-275
(item 22).
(e) Connect one end of line assembly 215T75074-275 (item 22) to the fluid port of the
aileron accumulator.
(f) Connect one end of line assembly 215T75074-273 (item 20) to the fluid port of the
elevator accumulator and the other end to the union AN815-4J in the tee fitting
AN938J4.
(g) Connect one end of line assembly 215T75074-274 (item 21) to the fluid port of the
rudder accumulator and the other end to the union AN815-4J in the tee fitting
AN938J4.
NOTE: It may be necessary to temporarily disconnect and reconnect some existing
bonding jumpers to permit installation of line assembly 215T75074-276 (item 23).
Refer to Figure 2 Detail E.
(h) Connect line assembly 215T75074-276 (item 23) between the existing aileron line
assembly 215T75063-48 and new line assembly 215T75074-275 (item 22) with two
unions AN815-6J (item 25).
Refer to Kit Drawing K215T75051, Sheet 5, View AD−AD, DETAIL PP, and SECTION F−F.
(12) Install new electrical bonding clamps and provisions for the line assemblies (Item 17, 18,
and 19) as follows:
(a) On the vertical channel, of the frame at FS 501.00, drill a 0.190 to 0.195 inch (4,83
to 4, 95 millimeter) hole at the location shown on DETAIL PP.
(b) Deburr the hole and apply anodizing solution to the bare metal areas.
(c) Install the three bonding jumpers MS25083 −2BB4 (Item 91) with the attaching
hardware as shown in SECTION F−F.
Refer to NOTE 19 of Kit Drawing Parts List.
(d) On each of the new line assemblies (Item 17, 18, and 19), fit a bonding clamp
AN735C4 (Item 61) and attach the lug end of the bonding jumpers MS25083−2BB4
(Item 91) with the attaching hardware as shown in SECTION F−F.
Refer to NOTE 19 of Kit Drawing Parts List.

### Page 19

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 18 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(13) Rework the three existing fairleads 215T75102-2 as follows:
Refer to Figure 2 Details F and J, and Kit Drawing K215T75051, Sheet 5, View AG-AG.
(a) Open up the existing hole to 0.375 inch (9.53 millimeters) diameter to suit the
installation of the new aileron line assemblies 215T75074-275 (item 22) and
215T75074-276 (item 23) as shown.
NOTE: Maintain a gap between the two fairlead halves prior to drilling the holes to
make sure that the two fairlead halves will have a tight fit around the line
assembly.
(b) Re-identify the fairlead as K215T75051-8.
Refer to kit drawing K215T75051, Sheet 5, View AG-AG.
(14) Install the three fairleads K215T75051-8 on the aircraft structure as shown by (item 8)
with bolts NAS6203−26 (item 87) and washers NAS1149D0332K (item 13) and new nuts
MS21042L3 (item 27).
Refer to Figure 2 Detail D and Kit Drawing K215T75051, Sheet 5, DETAIL AE.
(15) Install the accumulator mounting plate 215T75106-2 (item 4) as follows:
NOTE: All accumulator hydraulic line assemblies should remain attached to the
accumulators to locate the final position of the accumulator mounting plate on the
cabin ceiling in order to avoid pre-load and/or stress on the line assemblies.
(a) Do a final verification to make sure that the forward −inboard (pressure side) nutplate
will be located with a 0.85 inch (21.6 millimeters) distance from the edge of the
accumulator mounting plate 215T75106-2 (item 4) as shown.
(b) From the inside of the cabin, mark these rivet locations on the accumulator
mounting plate 215T75106-2 (item 4) and the angle 215T75051-50 (item 50).
1 Drill out the rivet locations, deburr and re-install the accumulator mounting plate
215T75106-2 and angle in place with Cleco pins.
2 Layout the rivet pitch and drill the 17 rivet locations in the two angles
215T75051-50 (item 50).  Secure the two together with Cleco pins.
(16) Mark the location of the six brackets support clamps 215T75101-2 on the accumulator
mounting plate 215T75106-2 (item 4).
(a) Install the 12 nutplates MS21059L4 (item 11) on the accumulator mounting plate as
shown.

### Page 20

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 19 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(17) Install the accumulator mounting plate 215T75106-2 (item 4) and two angles
215T75051-50 (item 50) on the cabin ceiling with rivets called.
(18) Secure the six bracket support clamps 215T75101-2 on the accumulator mounting plate
215T75106-2 (item 4) with 12 bolts NAS6204-3 (item 45) and 12 washers
NAS1149D0416K (item 46) and 12 shims 215T75057−2 (item 57).
(a) The two shims 215T75057 −2 (item 15) must be riveted to the accumulator mounting
plate with rivets called.  Refer to Figure 4 Detail C.
(19) Secure the three hydraulic line assemblies 215T75074-273 (item 20), 215T75074-274
(item 21), and  to the aircraft structure (and to the existing fuel line 215T64105-6) as
follows:
NOTE: To help with the drilling of the three holes in the frame at FS 501.00 and the
installation of the three nut plates to be installed in the frame at FS 481.50,
locally manufacture a drilling jig as shown in Figure 3.
Refer to kit drawing K215T75051, Sheet 5, Views AD-AD and AU-AU.
(a) Between stringers L3 and L5 at FS 501.00, drill three 0.189 to 0.192 inch (4.8 to 4.9
millimeters) diameter holes to the dimensions shown to suit the run of the three
hydraulic line assemblies.
1 Secure the three hydraulic line assemblies in place with three screws
MS35207-263 (item 14), three washers NAS1149D0332K (item 13), three nuts
B0203051-3 (item 33), and two clamps MS21919WDF4 (item 58), and one clamp
MS21919WDF6 (item 60).
Refer to Figure 2 Details H and K, and Kit Drawing K215T75051, Sheet 5, Views AR−AR
and AT−AT.
(b) Between stringers L3 and L5 at FS 481.50, install three nutplates MS21059L3
(item 9) to suit the run of the three hydraulic line assemblies.
1 Drill three 0.189 to 0.192 inch (4.8 to 4.9 millimeters) diameter holes to the
dimensions shown.
2 Secure the three hydraulic line assemblies in place with three screws
MS35207-267 (item 41), three washers NAS1149D0332K (item 13), and two
clamps MS21919WDF4 (item 58), one clamp MS21919WDF6 (item 60), and
three spacers NAS43DD3-31FC (item 31).
3 Secure the existing fuel line 215T64105-6 to the hydraulic line assembly
215T75074-275 (item 22) with a screw MS35207-269 (item 40), a washer
NAS1149D0332K (item 13), a nut B0203064-3 (item 15), a clamp
MS21919WDF6 (item 60), a clamp MS21919WDF16 (item 59) and a spacer
NAS43DD3-32FC (item 31).

### Page 21

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 20 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Refer to Figure 2 Detail H
(20) On the frame at FS 462.00 secure hydraulic line assembly 215T75074-275 (item 22) in
place on the bracket as shown with a clamp MS21919WDF6 (item 60), a screw
MS35207-263 (item 51), and a washer NAS1149C0332R (item 68).
(21) Secure the three hydraulic line assemblies 215T75074-270 (item 17), 215T75074-271
(item 18), and 215T75074-272 (item 19) to the aircraft structure as follows:
Refer to Figure 2 Detail G and Kit Drawing K215T75051 Sheet 2, Views AD-AD and
AF-AF.
(a) Install two nutplates MS21059L4 (item 9) on each of the supports K215T75051-54
(item 54) with rivets called to mate with the retained fairlead 215T75103-2.
(b) Install the two fairleads 215T75103-2 on the supports K215T75051-54 (item 54) and
clamp the three hydraulic line assemblies on the two fairleads 215T75103-2.
Secure with two bolts NAS6203−16 (item 65) and two washers NAS1149D0332K
(item 13).
(c) Determine the location of the support K215T75051-54 (item 54) on the channel
215-30077 and mark this location.
1 Install the supports on the channel 215-30077 with rivets called.
(22) Install the retained bonding jumpers as follows:
Refer to Figure 2 Details B and E, and Kit Drawing K215T75051 Sheet 5, VIEW AC-AC.
(a) Between the existing aileron hydraulic line assembly 215T75063-48 and the new
hydraulic line assembly 215T75074-208 (item 23), install one retained bonding
jumper MS25083-5BB4.  Secure the bonding jumper with:
NOTE: This was the location the aileron accumulator was installed.
Quantity Part No. Description Item No.
2 MS51958−65 Screw 55
2 AN735C6 Bonding Clamp 63
2 MS35338-138 Lock Washer 64
2 MS35650-304 Nut 86
6 NAS1149C0332R Washer 68

### Page 22

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 21 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(b) Between hydraulic line assembly 215T75074-208 (item 23) and  hydraulic line
215T75074-275 (item 22), install one retained bonding jumper MS25083-5BB4.
Secure the bonding jumper with:
Quantity Part No. Description Item No.
2 MS51958−65 Screw 55
2 AN735C6 Bonding Clamp 63
2 MS35338-138 Lock Washer 64
2 MS35650-304 Nut 86
6 NAS1149D0332R Washer 68
(c) Between hydraulic line assembly 215T75074-274 (item 21) and  hydraulic line
215T75074-273 (item 20), install one retained bonding jumper MS25083-5BB5 and
one bonding jumper MS25083-5BB4 as shown.  Secure the two bonding jumpers
with:
Quantity Part No. Description Item No.
3 MS51958−65 Screw 55
3 AN735C4 Bonding Clamp 61
3 MS35338-138 Lock Washer 64
3 MS35650-304 Nut 86
9 NAS1149D0332R Washer 68

### Page 23

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 22 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
215T75074−272
(LINE ASSY)
LEGEND
INSTALL NEW
REINSTALL
215T75074−275
(LINE ASSY)
215T75074−274
(LINE ASSY)
215T75074−273
(LINE ASSY)215T75074−276
(LINE ASSY)
215T75074−271
(LINE ASSY)
215T75074−270
(LINE ASSY)
AN832−4J
(BULKHEAD UNION)
(REF)

### Page 24

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 23 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
LEGEND
INSTALL NEW
REINSTALL
215T75051−56
(ACCESS PANEL ASSEMBLY)
K215T75051−58
(ANGLE)
K215T75051−36
(ANGLE)
K215T75051−44
(ANGLE)
K215T75051−42
(ANGLE)
215−30056−83
(BRACKET)
MS35207−263
(SCREW)NAS1149D0332K(WASHER)
MS35207−263
(SCREW)
NAS1149C0332R
(WASHER)
MS21919WDF6
(CLAMP)
AN735C4
(CLAMP)
MS51958−65
(SCREW)
MS35338−138
(LOCK WASHER)
MS35650−304
(NUT)
MS25083−5BB5
(BONDING
JUMPER)
MS25083−5BB4
(BONDING
JUMPER)
NAS1149C0332R
(WASHER)
NAS1149C0332R
(WASHER)

### Page 25

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 24 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
LEGEND
INSTALL NEW
REINSTALL
215T75106−2
(ACCUMULATOR MTG)
AN815−6J
(UNION)
MS25083−5BB4
(BONDING JUMPER)
K215T75051−50
(ANGLE)
K215T75051−50
(ANGLE)
NAS6204−3
(BOLT)
(CLAMP SUPPORT)
215T75101−2
(6 PLACES)
(RUDDER
MS28700−3
ACCUMULATOR)
(UNION)
AN815−5J
(3 PLACES)
(ELBOW)
AN939J5
(3 PLACES)
(PACKING)
MS28778−5
(9 PLACES)
215T75074−276
(LINE ASSY)
215T75074−275
(LINE ASSY)
(AILERON
MS28700−3
ACCUMULATOR)
(REDUCER)
AN919−3J
(3 PLACES)
(REDUCER)
AN919−12J
MS28778−5
(PACKING)
(REDUCER)
AN919−10J
MS28778−5
(PACKING)
(ELEVATOR
MS28700−3
ACCUMULATOR)
(REDUCER)
AN919−10J
MS28778−5
(PACKING)
NAS1149D0416K
(WASHER)
360−63−319−SH
(4 PLACES)
320−62P331SH
(4 PLACES)
(CLAMP)
1
2
360−63−319−SH
(2 PLACES)
320−62P331SH
(2 PLACES)
(CLAMP)
1
2
EFFECTIVITY
1
2
A/C 2001 TO 2015
A/C 2016 AND SUBS
NAS1149C0332R
(WASHER)
MS35338−138
(LOCK WASHER)
MS35650−304
(NUT)
MS51958−65
(SCREW)
AN735C6
(BONDING CLAMP)
(2 PLACES)
215T75057−2
(SHIM)
(6 PLACES)

### Page 26

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 25 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
MS21919WDF6
(CLAMP)
MS35207−263
(SCREW)
NAS1149D0332K
(WASHER)
MS35207−263
(SCREW)
NAS1149D0332K
(WASHER)
MS21919WDF4
(CLAMP)
LEGEND
INSTALL NEW
REINSTALL
215T75103−2
(FAIRLEAD)
K215T75051−54
(SUPPORT ASSY)
NAS1149D0332K
(WASHER)
1
NAS6203−16
(BOLT)
NAS1149D0332K
(WASHER)
REWORK EXISTING
FAIRLEAD 215T75102−2
AND REIDENTIFY AS
K215T75051−8
NAS6203−26
(BOLT)
NOTES
1 Use drilling jig to drill these
locations, refer to figure 3.
AN960−10L
(WASHER)
MS21042L3
(NUT)
REWORK EXISTING
FAIRLEAD 215T75102−2 AND
REIDENTIFY AS K215T75051−8
NAS6203−25
(BOLT)
B0203051−3
(NUT)
(3 PLACES)

### Page 27

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 26 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
LEGEND
INSTALL NEW
Use drilling jig to drill these
locations, refer to figure 3.
NOTE
1
1
MS21919WDF6
(CLAMP)
B0203064−3
(NUT)
NAS43DD3−32FC
(SPACER)
MS21919WDF16
(CLAMP)
MS35207−269
(SCREW)
MS21919WDF4
(CLAMP)
NAS1149D0332K
(WASHER)
(3 PLACES)
NAS43DD3−32FC
(SPACER)
(3 PLACES)
MS35207−267
(SCREW)
(3 PLACES)
215T64105−6
(FUEL LINE ASSY)
(REF)

### Page 28

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 27 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
MS51958−65
(SCREW)
(3 PLACES)
AN735C4
(BONDING CLAMP)
(3 PLACES)
MS35338−138
(LOCK WASHER)
(3 PLACES)
NAS1149C0332R
(WASHER)
(3 PLACES)
NAS1149C0332R
(WASHER)
(3 PLACES)
MS35650−304
(NUT)
(3 PLACES)
MS35207−267
(SCREW)
NAS1149D0332J
(WASHER)
(5 PLACES)
MS35338−43
(LOCK WASHER)
(2 PLACES)MS35650−302
(NUT)
(2 PLACES)
MS25083−2BB4
(BONDING JUMPER)
(3 PLACES)
215T75074−272
(LINE ASSY)
(REF)
215T75074−271
(LINE ASSY)
(REF)
215T75074−270
(LINE ASSY)
(REF)
RELOCATION OF THE  FLIGHT CONTROL HYDRAULIC ACCUMULATORS − INSTALLATION
FIGURE 2
LEGEND
INSTALL NEW

### Page 29

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 28 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
DRILLING JIG
FIGURE 3
DRILL JIG
DRILL JIG SHOWN
UPSIDE DOWN1
12
2
Refer to Kit drawing K215T75051
sheet 5 section AD for hole spacing.
2
Match the hole spacing with the hole
spacing in nut plate (MS21059L3).
3
3
4
Bolt with head turned down and drilled
in the middle to act as a metal sleeve.
4
NOTES
1 Locally make a drilling jig as shown to
install nut plates as shown on Kit drawing
K215T75051 sheet 5 views AV and AT−AT.

### Page 30

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 29 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
F. PART F − REWORK INSTALLATION (HARDWARE REPLACEMENT) USING
KIT NO. 215K4423D
The instructions of this paragraph (PART F) is intended for the rework of aircraft that have
installed the Kit No. 215K4423A (K215T75051−4 Installation).
The instructions that follow describe the necessary steps to rework the existing
(K215T75051−4 Installation to the equivalent of the 215K4423C Kit (K215T75051−10
Installation) standard.
The parts used in the following instructions are drawn from the Kit No. 215K4423D
(K215T75013−4 Installation).
Refer to Figure 4 Detail D and Kit Drawing K215T75013 Sheet 1 SECTION C−C.
(1) Release the flight control hydraulic system pressure.  Refer to PSP 492,
Chapter 29−00−00 HYDRAULIC POWER − MAINTENANCE PRACTICES.
(2) Remove the access panels 255-1, 255-2, and 255 −8.  Refer to PSP 492, Chapter
6−44−00, WING, PYLON, AND FLOAT ACCESS− DESCRIPTION AND OPERATION.
(3) Install the six shims 215T75057 −2 (item 4) as follows:
(a) Remove the aileron, rudder, and elevator accumulators.  Refer to the following
subjects in PSP 492, Chapter 27:
− 27−12−07 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph A.
− 27−22−03 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph A.
− 27−32−05 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph A.
(b) Remove and retain the 12 bolts NAS6204 −3, the 12 washers NAS1149D0416K, and
the six clamps 360−63−319−SH or 320−62P331SH.
NOTE: Clamp part number is aircraft Serial Number dependant.
(c) Drill out the existing rivets that secure the mounting plate 215T75106 −2 and the
angle K215T75051−50 to the aircraft structure.  Take care not to enlarge the existing
fastener holes.
(d) Install the six shims 215T75057 −2 (item 4) with the fasteners shown.
(e) Install the mounting plate 215T75106 −2 and the angle K215T75051−50 to the
aircraft structure with new rivets MS20470AD4−5A (item  14).
(f) Install the retained six clamps 360 −63−319−SH or 320−62P331SH using the
retained 12 bolts NAS6204−3 and the 12 washers NAS1149D0416K.
Torque the bolts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
NOTE: Clamp part number is aircraft Serial Number dependant.

### Page 31

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 30 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
(g) Install the aileron, rudder, and elevator accumulators.  Refer to the following
subjects in PSP 492, Chapter 27:
− 27−12−07 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph B.
− 27−22−03 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph B.
− 27−32−05 ACCUMULATOR − REMOVAL/INSTALLATION, Paragraph B.
Refer to Figure 4 Detail H and Kit Drawing K215T75013 Sheet 1, SECTION B−B and
SECTION E−E.
(4) Replace the attaching hardware for the 215T7503 −2 fairlead at FS 481.50 and FS 501.00
as follows:
(a) Remove and discard the existing two bolts AN3 −12 and the two washers
AN960KD10L.
(b) Install the two new attaching bolts NAS6203 −16 (tem 12) and two new washers
NAS1149D0332K (item 15).
Refer to Figure 4 Detail G and Kit Drawing K215T75013 Sheet 1, VIEW D−D.
(5) Replace the attaching hardware for the K215T75051 −8 fairlead at approximately FS 460
and BL 0.00  and BL 27.0 as follows:
NOTE: Fairlead  K215T75051 −8 was re-identified from 215T7503−2.
(a) Remove and discard the existing three bolts AN3 −17 and the three washers
AN960KD10L.  Retain the nuts MS21042L3.
(b) Install the three new attaching bolts NAS6203 −26 (item 13), three new washers L
NAS1149D0332K (item 15), and the three retained nuts MS21042L3.
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
Refer to Figure 4 Detail G and Kit Drawing K215T75013 Sheet 1, VIEW F−F.
(6) Replace the attaching hardware for the K215T75051 −8 fairlead at approximately
FS 460.00 and BL 13.5:
NOTE: Fairlead K215T75051 −8 was re-identified from 215T7503−2.
(a) Remove and discard the existing three bolts AN3 −17 and the three washers
AN960KD10L.  Retain the nuts MS21042L3.
(b) Install the three new attaching bolts NAS6203 −25 (tem 17), three new washers
NAS1149D0332K (item 15), and the three retained nuts MS21042L3.
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.

### Page 32

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 31 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Refer to Figure 4 Detail F and Kit Drawing K215T75013 Sheet 1, VIEW A−A.
(7) Replace the attaching hardware for the bonding jumper MS25083 −5BB4 at the
connection of the 215T75074−276 and the 215T75074−275 line assemblies at
approximately FS 462.00 and BL 6.00, as follows:
(a) Remove and discard the two MAS35207 −265 screws, the six AN960JD10L
washers, the two lock washers MS35338−43, the two nuts MS35650−302, and the
two bonding clamps AN735−6.  Retain the bonding jumper MS25085−5BB4.
(b) Re-install the bonding jumper MS25085 −5BB4 using the two new bonding clamps
AN735C6 (item 10), the two new screws MS51958−65 (item 3), the six new washers
NAS1149C0332R (item 5), the two new lock washers MS35338−138 (item 11), and
the two new nuts MS35650−304 (item 7).
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
Refer to Figure 4 Detail E and Kit Drawing K215T75013 Sheet 1, VIEW A−A.
(8) Replace the attaching hardware for the bonding jumper MS25083 −5BB4 at the
connection of the 215T75063−48 and the 215T75074−276 line assemblies at
approximately FS 450.00 and BL 45.00, as follows:
(a) Remove and discard the two MS35207 −265 screws, the six NAS1149D0332J
washers, the two lock washers MS35338−43, the two nuts MS35650−302, and the
two bonding clamps AN735−6.  Retain the bonding jumper MS25085−5BB4.
(b) Re-install the bonding jumper MS25085 −5BB4 using the two new bonding clamps
AN735C6 (item 10), the two new screws MS51958−65 (item 3), the six new washers
NAS1149C0332R (item 5), the two new lock washers MS35338−138 (item 11), and
the two new nuts MS35650−304 (item 7).
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
Refer to Figure 4 Detail C and Kit Drawing K215T75013 Sheet 1, VIEW A−A.
(9) Replace the attaching hardware for the clamp MS21919WDF −6 located approximately
along FS 462.00 and above stringer 3, left side as follows:
(a) Remove the screw MS35207 −263 and the washer AN960KD10L.  Retain the screw
and discard the washer.
(b) Install the screw MS35207 −263 and the new washer NAS1149C0332R (item 5).

### Page 33

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 32 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Refer to Figure 4 Detail J and Kit Drawing K215T75013 Sheet 1, VIEW A−A.
(10) Replace the attaching hardware for the bonding jumpers MS25083 −5BB4 and
MS25083−5BB5, that attach to the 215T75074−273, the 215T75074−274, and
215T75079−16 line assemblies, as follows:
(a) Remove the three screws MS35207 −265, the 9 washers AN960JD10L, the three
lock washer MS35338−43, the three nuts MS35650−302, and the two bonding
jumpers MS25083−5BB4 and MS25083−5BB5.
Retain the two bonding jumpers MS25083−5BB4 and MS25083−5BB5 and discard
all other parts.
(b) Fit three new bonding clamps AN735C4 (item 8) and re-install the two bonding
jumpers MS25083−5BB4 and MS25083−5BB5 using three new screws
MS51958−65 (item 3), 9 new washers NAS1149C0332R (item 5), three lock
washers MS338−138 (item 11), and three new nuts MS35650−304 (item 7).
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
(11) Install the access panel 255 −8.  Refer to PSP 492, Chapter 6−41−00, FUSELAGE
ACCESS− DESCRIPTION AND OPERATION.
(12) Perform the testing as described in Paragraph H.

### Page 34

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 33 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
REPLACEMENT / INSTALLATION OF COMMON HARDWARE
FIGURE 4
215T75074−273
(LINE ASSY)
(REF)
215T75074−274
(LINE ASSY)
(REF) 215T75074−275(LINE ASSY)
(REF)
215T75074−276
(LINE ASSY)
(REF)
MS35207−263
(SCREW)
AN960KD10L
NAS1149C0332R
(WASHER)
MS21919WDF−6
(CLAMP)
(REF)
LEGEND
REMOVE AND DISCARD (SCRAP)
REINSTALL
INSTALL NEW

### Page 35

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 34 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
REPLACEMENT / INSTALLATION OF COMMON HARDWARE
FIGURE 4
(CLAMP SUPPORT)
215T75101−2
(REF)
215T75057−2
(SHIM)
(6 PLACES)
NAS1149D0416K
(WASHER)
(12 PLACES)
NAS6204−3
(BOLT)
(12 PLACES)
(LINE ASSY)
215T75074−276
(REF)
LEGEND
REMOVE AND DISCARD (SCRAP)
REINSTALL
INSTALL NEW
AN735−6
AN735C6
(BONDING CLAMP)
MS35207−265
MS51958−65
(SCREW)
MS25083−5BB4
(BONDING JUMPER)
AN960JD10L
(WASHER)
MS35338−43
MS35338−138
(LOCK WASHER)
(LINE ASSY)
215T75074−275
(REF)
AN735−6
AN735C6
(BONDING CLAMP)
MS35207−265
MS51958−65
(SCREW)
NAS1149D0332J
NAS1149C0332R
(WASHER)
(LINE ASSY)
215T75074−276
(REF)
MS35338−43
MS35338−138
(LOCK WASHER)
MS25083−5BB4
(BONDING JUMPER)
MS35650−302
MS35650−304
(NUT)
MS35650−302
MS35650−304
(NUT)
NAS1149C0332R
(WASHER)

### Page 36

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 35 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
REPLACEMENT / INSTALLATION OF COMMON HARDWARE
FIGURE 4
215T75103−2
(FAIRLEAD)
REWORK EXISTING
FAIRLEAD 215T75102−2
AND REIDENTIFY AS
K215T75051−8
AN960KD10L
NAS1149D0332K
(WASHER)
AN735−4
AN735C4
(CLAMP)
MS35207−265
MS51958−65
(SCREW)
MS35338−43
MS35338−138
(LOCK WASHER)
MS35650−302
MS35650−304
(NUT)
MS25083−5BB5
(BONDING
JUMPER)
MS25083−5BB4
(BONDING
JUMPER)
LEGEND
REMOVE AND DISCARD (SCRAP)
REINSTALL
INSTALL NEW
AN3−12
NAS6203−16
(BOLT)
AN960KD10L
NAS1149D0332K
(WASHER)
K215T75051−54
(SUPPORT ASSY)
(REF)
NAS6203−26
(BOLT)
(BOLT)
AN3−17
MS21042L3
(NUT)
REWORK EXISTING
FAIRLEAD 215T75102−2 AND
REIDENTIFY AS K215T75051−8
AN960KD10L
NAS1149D0332K
(WASHER)
AN960JD10L
(WASHER)
NAS1149C0332R
(WASHER)
AN960JD10L
(WASHER)
NAS1149C0332R
(WASHER)
NOTE
1
1
For K215T75051−4 Installation.
AN3−17
(BOLT)
NAS6203−26
(BOLT)
NAS6203−25
(BOLT)

### Page 37

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 36 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
G. PART G − REWORK INSTALLATION (HARDWARE REPLACEMENT) USING KIT
NO. 215K4423E
Kit No. 215K4423E is intended as a second rework kit for aircraft having installed Kits
No. 215K4423 (Basic) and 215K4423B (K215T75013−2 Rework Installation).
The parts used in the following instructions are drawn from the Kit No. 215K4423E (a partial
K215T75013−4 Installation).
Refer to Figure 4 Details G and H, and Kit Drawing K215T75013 Sheet 1, VIEW D−D and
VIEW F−F.
(1) Remove the access panels 255-1, 255-2, and 255 −8.  Refer to PSP 492,
Chapter 6−44−00, WING PYLON, AND FLOAT ACCESS− DESCRIPTION AND
OPERATION.
(2) Replace the attaching hardware for the three K215T75051 −8 fairleads at approximately
FS 460 and BL 0.00, BL 13.5, and at BL 27.0 as follows:
NOTE: Fairlead  K215T75051 −8 was re-identified from 215T7503−2.
(a) At the three locations, remove and discard the existing bolts NAS6203 −26 and the
washers AN960KD10L.  Retain the nuts MS21042L3.
(b) At the three locations, install the three new attaching bolts NAS6203 −25 (tem 17),
three new washers NAS1149D0332K (item 15), and the three retained nuts
MS21042L3.
Torque the nuts to standard values.  Refer to PSP 492 Chapter 20−21−00
TORQUING OF THREADED FASTENERS − MAINTENANCE PRACTICES.
(3) Install the access panels 255-1, 255-2, and 255 −8.  Refer to PSP 492, Chapter 6−44−00,
WING, PYLON, AND FLOAT ACCESS− DESCRIPTION AND OPERATION.
(4) If rework is limited to the installation of this Kit No. 215K4423E, no testing is required.
Proceed to Paragraph I. Recording.

### Page 38

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 37 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
H. Testing
(1) Do a leak check as follows:
NOTE: Make sure a second technician verifies all line connections while the flight
controls are being cycled.
(a) Replenish the aileron, elevator, and rudder hydraulic and nitrogen systems.  Refer to
PSP 492, Maintenance Manual, Chapter 12.
(b) Apply leak test solution MIL-L-25567, Type 1 to all of the new line assembly
connections, unions, and reducers and do a leak check of each connection.
(c) Switch the aileron control system to NORMAL mode.  Refer to PSP 492,
Maintenance Manual, Chapter 27-10-00
(d) Switch the rudder control system to NORMAL mode.  Refer to PSP 492,
Maintenance Manual, Chapter 27-20-00
(e) Switch the elevator control system to NORMAL mode.  Refer to PSP 492,
Maintenance Manual, Chapter 27-30-00
(f) Cycle the three flight (aileron, rudder, and elevator) controls twice.  Check for leaks
at all new line connections.
(2) Do an operational test as follows:
(a) Remove DC power from the aircraft.  Refer to PSP 492, Chapter 24.
(b) Release the hydraulic test stand pressure.  Refer to PSP 492, Chapter 29.
(c) Verify that the accumulator pressure is sufficient to operate the ailerons.
1 Turn the control hand wheel completely to the left and then completely to the
right, a minimum of four times, to cycle the ailerons.
(d) Press the rudder pedals forward and aft to cycle the rudder a minimum of three
times.
(e) Verify that the accumulator pressure is sufficient to operate the elevators.
1 Push and pull the control column a minimum of three times to cycle the elevators.
I. Recording
When this Service Bulletin is completed, make the entry in the aircraft log book and send back
the attached Incorporation Notice to Specialized and Amphibious Aircraft Technical
Publications.

### Page 39

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 38 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
3. Material Information
A. Kit No. 215K4423 − Parts List
The Kit No. 215K4423 which consisted of the K215T75051−2 installation is no longer
available.  As of Revision 4 of this Service Bulletin, first time installation of this modification
should use the Kit 215K4423C.
If you have received this kit, and have not yet installed it, you will require the addition of the
rework Kit 215K4423D to incorporate the equivalent of the 215K4423C Kit (K215T75051−10
Installation).
B. Kit No. 215K4423A − Parts List
The Kit No. 215K4423A which consisted of the K215T75051−4 installation is no longer
available.  As of Revision 4 of this Service Bulletin, first time installation of this modification
should use the Kit 215K4423C.
If you have received this kit, and have not yet installed it, you will require the addition of the
rework Kit 215K4423D to incorporate the equivalent of the 215K4423C Kit (K215T75051−10
Installation).
C. Kit No. 215K4423B − Parts List
The Kit No. 215K4423B Rework Kit which consisted of the K215T75013−2 Installation is no
longer available. As of Revision 4 of this Service Bulletin, aircraft that have installed the Kit No.
215K4423 should install the rework kit 215K4423D.
If you have a 215K4423B rework kit in stock and had need to install it − order a 215K4423E to
use in conjunction.  This will be necessary in order to rework your aircraft installation to the
equivalent of the 215K4423C Kit (K215T75051−10 Installation) standard.
D. Kit No. 215K4423C − Parts List
Kit No. 215K4423C is necessary to do this Service Bulletin.  This Kit consists of the
K215T75051−10 Installation and includes the parts that follow:
NOTE: This Kit No. 215K4423C is intended, as of Revision 4 of this Service Bulletin, to be the
standard-first time installation of this modification and therefore supersedes
Kit No. 215K4423 and Kit No. 215K4423A.
PART NO. QUANTITY DESCRIPTION DRW ITEM
K215T75051−56 1 Door Panel Assembly 56
215T75106−2 1 Accumulator Mounting
Bracket
4
MS21059L3 38 Nut Plate 9

### Page 40

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 39 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Kit No. 215K4423C − Parts List (cont’d)
PART NO. QUANTITY DESCRIPTION DRW ITEM
MS21059L4 12 Nut Plate 11
NAS1149D0332K 45 Washer 13
MS35207−263 34 Screw 14
B0203064−3 1 Nut 15
215T75074−270 1 Line Assembly 17
215T75074−271 1 Line Assembly 18
215T75074−272 1 Line Assembly 19
215T75074−273 1 Line Assembly 20
215T75074−274 1 Line Assembly 21
215T75074−275 1 Line Assembly 22
215T75074−276 1 Line Assembly 23
AN815−6J 2 Union 25
MS21042L3 3 Nut 27
MS35338−43 2 Lockwasher 28
AN939J5 3 Elbow 29
NAS43DD3−32FC 4 Spacer 31
B0203051−3 3 Nut 33
AN815−5J 3 Union 34
K215T75051−36 1 Angle 36
215−30056−83 1 Bracket 39
MS35207−269 1 Screw 40
MS35207−267 4 Screw 41
K215T75051−42 1 Angle 42
K215T75051−44 1 Angle 44
NAS6204−3 12 Bolt 45
NAS1149D0416K 12 Washer 46
MS35650−302 2 Nut 48
NAS1149D0332J 5 Washer 49
K215T75051−50 2 Angle 50

### Page 41

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 40 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
Kit No. 215K4423C − Parts List (cont’d)
PART NO. QUANTITY DESCRIPTION DRW ITEM
MS35207−263 1 Screw 51
K215T75051−54 2 Support 54
MS51958−65 10 Screw 55
215T75057−2 6 Shim 57
MS21919WDF4 4 Clamp 58
MS21919WDF16 1 Clamp 59
MS21919WDF6 4 Clamp 60
AN735C4 6 Bonding Clamp 61
AN735C6 4 Bonding Clamp 63
MS35338−138 10 Lockwasher 64
NAS6203−16 4 Bolt 65
NAS1149C0332R 37 Washer 68
NAS1097AD3−4A 6 Rivet 70
MS20426AD3−3A 74 Rivet 71
MS20470AD4−3A 17 Rivet 72
MS20470AD4−4A 19 Rivet 73
MS20470AD4−5A 104 Rivet 74
MS20470AD5−5A 26 Rivet 75
NAS1738B5−2 23 Rivet 76
MS20470AD5−6A 17 Rivet 78
K215T75051−58 1 Angle 81
MS35650−304 10 Nut 86
NAS6203−26 6 Bolt 87
NAS9301B−4−04 17 Rivet 88
320−62P331SH 2 Band Clamp 89
NAS6203−25 3 Bolt 90
MS25083−2BB4 3 Bonding Jumper 91

### Page 42

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 41 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
E. Kit No. 215K4423D (Rework)  − Parts List
Kit No. 215K4423D (Rework) may be necessary to complete this Service Bulletin and consists
of the K215T75013−4 Installation that includes the parts that follow:
NOTES: 1. This Kit , as of Revision 4 of this Service Bulletin, is intended to be the standard
rework Kit for those aircraft which have installed Kits No. 215K4423
(K215T75051−2 Installation) only .  This Kit therefore supersedes the Rework
Kit No. 215K4423B
2. This Rework Kit will also be necessary to incorporate the equivalent of the
215K4423C Kit (K215T75051−10 Installation) for those aircraft which have
incorporated the 215K4423A (K215T75051−4 Installation) only.
PART NO. QUANTITY DESCRIPTION DRW ITEM
MS51958−65 7 Screw 3
215T75057−2 6 Shim 4
NAS1149C0332R 22 Washer 5
MS35650−304 7 Nut 7
AN735C4 3 Bonding Clamp 8
AN735C6 4 Bonding Clamp 10
MS35338−138 7 Lockwasher 11
NAS6203−16 4 Bolt 12
NAS6203−26 6 Bolt 13
MS20470AD4−5A 18 Rivet 14
NAS1149D0332K 13 Washer 15
MS21042L3 3 Nut 16
NAS6203−25 3 Bolt 17

### Page 43

MODEL CL-215-6B11 (415)
SERVICE BULLETIN
Bombardier 415
Service Bulletin 215-4423Rev. NC.  April 4/11
ATA Ref: 27-20Page 42 of 42
Rev 5  March 17/16
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this Service Bulletin is performed in compliance with manufacturer’s recommendations
and/or acceptable industry standards.  This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by any means without the prior 
written consent of Bombardier Inc. or its affiliates.  This disclaimer applies to this, and all Service Bulletins listed in the 215−4000 Index, and those posted on the Bombardier Amphibious Aircraft 
web site:  www.support.amphibious.bombardier.com.
F. Kit No. 215K4423E (Rework) − Parts List
Kit No. 215K4423E may be necessary to incorporate the equivalent of the 215K4423C Kit
(K215T75051−10 Installation) and consists of replacement bolts and washers (items 15 and17
only) from the K215T75013−4 Rework Installation.
This kit will be necessary if both the conditions that follow, are present:
− The Kit No. 215K4423 (K215T75051−2 Installation) has been installed.
− The Kit No. 215K4423B (K215T75013−2 Installation) has been installed.
PART NO. QUANTITY DESCRIPTION DRW ITEM
NAS1149D0332K 3 Washer 15
NAS6203−25 3 Bolt 17
G. The following materials, or equivalent, are necessary to do this Service Bulletin. You can buy
them locally:
DESCRIPTION PART NO./NAME SPECIFICATION QUANTITY
Aerodynamic 
Sealant
Pro Seal 870
Class B−2 or
equivalent
MIL-S-81733 
Type 2
A/R
Anodizing Solution Alodine 1200S
or equivalent
MIL-C-5541 
Class 1A
A/R
Faying Surface
Sealant
Pro Seal 870
Class C or 
equivalent
MIL-S-81733 
Type 4
A/R
Humiseal 1B15 − A/R
Fluid Resistant Epoxy
Primer
Commercial BAMS 565-001 or
equivalent
A/R
Packing MS28778−5 A/R
Packing MS28778−8 A/R

### Page 44

Upon completion of Service Bulletin(s), please fill in and return by fax to:
Service Bulletin Number(s) Rev.
Aircraft Serial No.
Date of Incorporation
Aircraft Reg. No.
Technical Publication,
Dept. 649-DBF−(9)
Bombardier Aerospace
Specialized &
Amphibious Aircraft
St. Laurent, Quebec
Fax No.: (514) 855−7602
Airframe Hours
Remarks
Name
SERVICE BULLETIN
INCORPORATION NOTICE
REPLY FAX
Customer/Operation
(Please Print)
the evolution of mobility

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
