# Bombardier Service Bulletin 350-24-005

Copy: No revision named ("350-24-005"), 10 pages: PDF https://openairdocs.org/files/sha256/6e/52/6e52c3c1509cc95af0e514bfd4b41804a4d9b46ef0f20598f9701d3e7f4dad68; text https://openairdocs.org/service-documents/bombardier/sb-350-24-005/file/6e52c3c1509c.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1662; AD 2023-11-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 350-24-005
- Page: https://openairdocs.org/service-documents/bombardier/sb-350-24-005

## ADs that cite it (2) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2024-18-03](https://openairdocs.org/ad/2024-18-03.md), effective Nov 12, 2024: No revision named
- [AD 2023-11-01](https://openairdocs.org/ad/2023-11-01.md), effective Aug 15, 2023: No revision named

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-350-24-005/proposed.md).

## Text (10 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2022-1662; AD 2023-11-01 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

SPECIAL CHECK/MODIFICATION – DC POWER CENTER (DCPC) SYSTEM –
INSTALLATION OF PROTECTIVE TAPE ON THE LEFT DCPC CARD CAGE
The information below is provided for your reference. For full details, including labor and part
coverage, please see corresponding paragraph contained within this bulletin.
RECOMMENDED
SPECIFIED TIME COMPLIANCE
COMPLIANCE TIME
Refer to Paragraph 1.D.
EFFECTIVITY: A/C Serial No. 20501 to 20929, and 20931
MANPOWER: 2 man−hours
CONTINUED AIRWORTHINESS (CAW)
FLEET CAMPAIGN NOYES
TLMC, CH 5 AFFECTED NOYES
KITS and/or PARTS YES NO
TOOLING/GSE YES NO
PLANNING INFORMATION: See important
information at the start of Paragraph 1. YES NO
DEDICATED SCHEDULE NOYES
PREREQUISITE SERVICE BULLETINS: SB 350−24−004 is a prerequisite and must be
done before or at the same time as this Service Bulletin.
NOTE: This Service Bulletin may be subject to an Airworthiness Directive which will make
it necessary to implement this Service Bulletin.
To place an order for parts, please call Bombardier Aviation Parts Services at:
514−855−2999 or 1−866−538−1247
SERVICE BULLETIN SUMMARY
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−350)
ATA 24−61
ELECTRICAL POWER
Basic Issue: Nov 29/2022 350−24−005
Page 1 of 1
This Service Bulletin is available at:

### Page 2

SPECIAL CHECK/MODIFICATION – DC POWER CENTER (DCPC) SYSTEM –
INSTALLATION OF PROTECTIVE TAPE ON THE LEFT DCPC CARD CAGE
1. PLANNING INFORMATION
NOTES:1 . Before you do this Service Bulletin, examine all STC, STA or
equivalent action changes to make sure that this Service Bulletin can
be completed.
2. This Service Bulletin is only applicable for aircraft with left DC Power
Center (DCPC) part number 975GC02Y07.
3. SB 350−24−004 is a prerequisite and must be done before or at the same
time as this Service Bulletin.
A. Effectivity
BD−100−1A10 aircraft, Serial No. 20501 to 20929, and 20931.
NOTE: The instructions given in this Service Bulletin are only applicable to the
systems and parts installed at the time of delivery of the aircraft or as
changed by Bombardier Aviation Service Bulletin(s).
B. Reason
1. Condition:
Reports found that aircraft may experience penetration of dust on logic and
protection boards of left DC Power Center (DCPC), which can lead to
misleading indication.
SERVICE BULLETIN
my.businessaircraft.bombardier.com
MODEL BD−100−1A10 (CH−350)
ATA 24−61
ELECTRICAL POWER
Refer to applicable governmental agency regulations and requirements and make sure that the work described in this
Service Bulletin is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards.
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or
by any means without the prior written consent of Bombardier Inc. and/or its affiliates.
 2022 Bombardier Inc.  All rights reserved
Learjet, Challenger, Global, are registered trademarks of Bombardier Inc. or its subsidiaries.
Basic Issue: Nov 29/2022 350−24−005
Page 1 of 7
This Service Bulletin is available at:

### Page 3

2. Objective/Benefit:
This Service Bulletin instructs to install a protective layer of tape on the left
DCPC card cage to prevent future contamination of electronic boards and
thereby prevent misleading indication and repetitive cleaning.
C. Description
This Service Bulletin gives instructions to:
− Get access to the left DCPC, Part No. 975GC02Y07.
This Service Bulletin gives instructions in PART A, to:
− Establish the left DCPC total flight hours.
This Service Bulletin gives instructions in PART B, to :
− Do the modification of the left DCPC, Part No. 975GC02Y07, as given in the
attached Safran Electrical & Power (ECE), Service Bulletin 975GC02Y−24−020,
and
− Re−identify the left DCPC after modification.
After PART B, as applicable:
− Do the necessary tests to make sure that the system operates correctly.
D. Compliance
Recommended on or before Dec 31/2023.
NOTE: If it is not possible to complete all the instructions in this Service Bulletin
because of the aircraft configuration, submit an SRPSA for analysis and to
get an approved disposition to complete this Service Bulletin. Standard
SRPSA fees may apply. Refer to the Services section of the Bombardier
Customer Portal for the latest prices, rates and fees.
E. Approval
The technical content of this Service Bulletin has been approved under the
authority of Transport Canada Civil Aviation (TCCA) Design Approval Organization
(DAO) No. DAO #93−Q−02.
NOTES: 1. The technical content of this Service Bulletin is accepted by the FAA
under the Canada/USA bilateral Aviation Safety Agreement.
2. The technical content of this Service Bulletin is accepted by EASA
under the Canada/EU bilateral Aviation Safety Agreement.
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 2 of 7

### Page 4

F. Manpower
NOTES: 1. The man−hours given are to help you schedule the tasks given in this
Service Bulletin. The man−hours are for direct labor performed by an
experienced crew and do not include the time for familiarization,
planning, aircraft preparation in hangar such as towing and
positioning of scaffolds, removal of interior furnishings, repainting,
supervision and inspection.
For more information related to the manpower, refer to
SB 350−00−002.
2. Labor hours are based on the fact that the modification will be done at
the next scheduled maintenance task or inspection. Therefore no
man−hours are allotted to prepare the aircraft for maintenance or to
prepare for this Service Bulletin.
2 man−hours are necessary to do this modification.
The labor required to do this Service Bulletin is at no cost if:
− the work is done during new aircraft warranty period, and
− the work is done at Bombardier Business Aviation Services (BBAS) or
Authorized Service Facilities (ASF), and
− this Service Bulletin is scheduled on or before Dec 31/2023.
G. Material − Cost and Availability
No kit is necessary to do this modification.
The parts in Paragraph 3.B. are necessary to do this Service Bulletin.
The parts are available at no cost if:
− a no−charge purchase order is sent to Bombardier Aviation before Dec 31/2023.
For all parts transactions, Bombardier Aviation’s current Spare Parts and
Component Repair Price Catalogue General Terms and Conditions apply. These
terms and conditions are found on the Bombardier Customer Portal at:
my.businessaircraft.bombardier.com
For those aircraft out of new aircraft warranty at the time of Service Bulletin release,
Smart Parts pays for the parts for up to Dec 31/2023.
H. Tooling
The equipment and tools listed below are necessary to do this modification:
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 3 of 7

### Page 5

GSE REFERENCE NO. PART NO. DESCRIPTION
Commercially Available −
Permanent Marker
(or)
Label Printer
Commercially Available − Torque Wrench
NOTES: 1. Refer to the BD−100 Illustrated Tool and Equipment Manual (ITEM) to
make sure that you use the correct equipment configuration.
2. Refer to the Liability Statement in the ITEM for the BD−100 for
acceptable GSE equivalents.
3. This list is provided for a quick reference. In case of discrepancy
between this list and the tool called out in the SPM−WM, Chapter 20,
then the tool called in the SPM−WM will prevail. Other approved
alternative tools are acceptable and can also be used.
I. Weight and Balance
No change.
J. Electrical Load Data
No change.
K. References
− TCCA Airworthiness Directive (pending).
− Bombardier Aviation, Modification Summary, BB100T011121, Rev. A.
− Bombardier Aviation, Kit Drawing, K1000070496, Rev. −−.
− Safran Electrical & Power (ECE), Service Bulletin 975GC02Y−24−020
(Attached).
− Bombardier Aviation, Standard Practices Manual (SPM), Chapter 51.
− CH 350 Aircraft Maintenance Manual (AMM), Chapters 6, 24 and 52.
L. Other Publications Affected
None.
M. Equivalent Service Bulletin
− For the Challenger 300 aircraft, use Service Bulletin 100−24−30.
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 4 of 7

### Page 6

2. ACCOMPLISHMENT INSTRUCTIONS
NOTES: 1. All TASKs given in the procedures that follow are from the BD−100,
Aircraft Maintenance Manual (AMM) unless otherwise specified.
2. All references made to zones, access panels and/or doors, are from the
BD−100 Aircraft Maintenance Manual (AMM), Chapter 6.
A. Aircraft Setup
(1) Obey all the electrical/electronic safety precautions. Refer to
AMM 24−00−00−910−801.
(2) Obey all the electrostatic−discharge safety precautions. Refer to
AMM 24−00−00−910−802.
(3) Open the aft equipment compartment door (182GL). Refer to
AMM 52−41−00−010−801.
(4) Disconnect the batteries. Refer to AMM 24−32−00−040−801.
B. PART A — Special Check — Left DCPC Total Flight Hours and Aircraft
Delivery Date
NOTE: If it is not possible to establish the total flight hours of left DCPC, submit an
SRPSA by email at SRPSA@aero.bombardier.com and request for
assistance to determine the flight hours of the unit.
(1) Establish the left DCPC total flight hours (since date of manufacture) and
aircraft delivery date.
NOTE: For the original left DCPC units, the total flight hours accumulated is
the same than the aircraft total accumulated flight hours.
(a) For the original units (installed at aircraft delivery) with less than 3500 total
flight hours accumulated and SB 350−24−004 not incorporated, no further
action is required. Proceed to Paragraph 2.E. Close−out.
NOTE: This Service Bulletin is recommended before Dec 31/2023. Units
that have not reached the 3500 flight hours threshold at the
moment of this check might reach it before Dec 31/2023.
(b) If SB 350−24−004 is already incorporated on the aircraft, then incorporate
PART B of this SB 350−24−005.
(c) If SB 350−24−004 is not incorporated and the original unit has more than
3500 flight hours, do the SB 350−24−004 for replacement of left DCPC,
and
Go to Paragraph 2.E. Close−out of this Service Bulletin.
NOTE: PART B of this SB 350−24−005 will be incorporated by the
supplier at the same time as SB 350−24−004.
(d) If aircraft was delivered after January 2020 with original unit, then
incorporate PART B of this SB 350−24−005.
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 5 of 7

### Page 7

C. PART B — Modification — Installation of Protective Tape on the Left DCPC
Card Cage
NOTE: If it is not possible to complete all the instructions of this Service Bulletin
because of the configuration of the aircraft, submit an SRPSA for analysis
and to get an approved disposition to complete this Service Bulletin.
(1) Do the modification of the left DCPC, Part No. 975GC02Y07, to install the
protective tape, Part No. RUBATV090−13L100, as given in the attached
Safran Electrical & Power (ECE), Service Bulletin 975GC02Y−24−020.
NOTE: Make sure to cut to a length of 1.77 in (45 mm).
(2) After modification, re−identify the left DCPC, Part No. 975GC02Y07, as
975GC02Y08, with the identification label, Part No. NPP000114AAY00.
D. Testing
(1) Connect the batteries. Refer to AMM 24−32−00−440−801.
(2) Do the testing of DCPC logic and protection cards as follows:
(a) Energize the primary dc power supply. Refer to AMM 24−31−00−861−801.
(b) The Power−Up Built−In−Test (PBIT) starts automatically when you apply
electrical power to the aircraft. Make sure that the Engine Indication and
Crew Alerting System (EICAS) does not show the messages that follow:
EICAS MESSAGE LEVEL (COLOR)
ELECTRICAL FAULT Caution (amber)
ELECTRICAL FAULT Advisory (cyan)
(3) Do the operational test of the main generator to test the LH GCU card. Refer to
AMM 24−31−05−710−801.
E. Close−out
(1) Remove all tools, equipment and unwanted materials from the aircraft.
(2) Close the aft equipment compartment door (182GL). Refer to
AMM 52−41−00−410−801.
F. Recording
You can do each PART of this Service Bulletin independently. When any PART of
this Service Bulletin is completed, make an entry in the aircraft log and send the
attached Incorporation Notice to Bombardier Business Aircraft Customer Services
(BBACS).
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 6 of 7

### Page 8

For information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin
Group at the following email address:
bbad_SBgroup@aero.bombardier.com
3. MATERIAL INFORMATION
A. Kit
No kits required.
B. Parts
The parts that follow are necessary to do this Service Bulletin and are available
from Bombardier Aviation Parts Services, Montreal:
NEW PART NO. QTY ITEM USED PARTNO. INSTRUCTION-DISPOSITION
NPP000114AAY00 1 IdentificationLabel NP0000590ABY00 −
RUBATV090−13L100
(See Note 2)
2 in
(50.
8 mm)
Protective
Tape
(PTFE
Coated
Glass Fabric)
− −
NOTES: 1. The part numbers for the items listed above is subject to change
without revision to this Service Bulletin. In case of discrepancy
between this list and any other list, the Illustrated Parts Catalog
prevails and shall be used to determine the latest part number.
2. Make sure to cut to a length of 1.77 in (45 mm).
C. Material
No materials required.
D. Publications
No publications required.
MODEL BD−100−1A10 (CH−350)
Basic Issue: Nov 29/2022 350−24−005
Page 7 of 7

### Page 9

350−24−005 Basic Nov 29/2022
SPECIAL CHECK/MODIFICATION – DC POWER CENTER (DCPC)
SYSTEM – INSTALLATION OF PROTECTIVE TAPE ON THE LEFT DCPC
CARD CAGE
bbad_SBgroup@aero.bombardier.com
NOTE: Please use Salesforce only for troubleshooting issues or when Engineering
deviation is necessary to accomplish the Service Bulletin modification.
SERVICE BULLETIN EVALUATION FORM
(Your ideas will help us provide better bulletins)
SERVICE BULLETIN: ISSUE: DATED:
TITLE:
For any information, correction(s), comment(s) and/or feedback regarding Service
Bulletins released on the Customer Portal, please contact the Service Bulletin Group
at the following email address:

### Page 10

SERVICE BULLETIN INCORPORATION SHEET − "350−24−005"
Upon completion of the Service Bulletin, please fill−in, fax to
(514) 855−8798 or e−mail to Fracas at fracas.montreal@aero.bombardier.com
If you’re reporting Service Bulletin (SB) Incorporations to CAMP, sending
this Incorporation Sheet to Bombardier is not mandatory. If your aircraft is
on another tracking system, please contact Bombardier to make arrangements
for automated data submission.
350−24−005 Basic
COMPLIED WITH
YES    NO    N/A
PART A
PART B
Actual hours to accomplish Service Bulletin:
* NOTES:
Aircraft Serial No. Aircraft Reg. No.
Airframe Hours: Airframe Landings
S.B. Incorporation Date Service Order No.
Facility incorporating S.B.
Name Signature Date
BOMBARDIER
SUBMISSION
Service Bulletin
Number
Rev. * Parts
Completed
Remarks/Reason
(Mandatory if N/A)
1. Where the Service Bulletin is divided into a number of parts (e.g., PARTS A,
B, C, D, etc.) which can be carried out separately, indicate only those parts
completed at this time.
2. For repetitive checks (usually PART A) only the initial check should be
reported unless otherwise stated in the Service Bulletin.
3. When more than one part is carried out at the same time, each part should
be reported.
4. Fill in ’Remark/Reason’ to explain compliance method when N/A is selected.(E.g. Part
not installed, N/A by effectivity, N/A by Part Serial Number, etc.
5. PCW means ’Previously Complied With’.
(dd/mm/yy)
Signature not required if sent by E−Mail (dd/mm/yy)

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
