# Bombardier Service Bulletin 40-78-03

Copy: Revision 1 ("Learjet Service Bulletin 4"), 16 pages: PDF https://openairdocs.org/files/sha256/e4/84/e484cf908db65f0ab5d4b9aa4ca30105326ac308f0fceadb4727721857385058; text https://openairdocs.org/service-documents/bombardier/sb-40-78-03/file/e484cf908db6.md. Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0010; AD 2014-13-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication.

## Details

- Manufacturer: [Bombardier](https://openairdocs.org/service-documents/bombardier.md)
- Type: Service bulletin (Service Bulletin)
- Number: 40-78-03
- Latest revision known: 40-78-03, Revision 1, dated November 5, 2012 (OpenAirDocs)
- Page: https://openairdocs.org/service-documents/bombardier/sb-40-78-03

## ADs that cite it (1) (OpenAirDocs)

Newest first, with the revision each names, as OpenAirDocs read it from the AD's text.

- [AD 2014-13-06](https://openairdocs.org/ad/2014-13-06.md), effective Aug 19, 2014: Revision 1

Also cited in [1 proposed AD](https://openairdocs.org/service-documents/bombardier/sb-40-78-03/proposed.md).

## Text (16 pages)

Rights: © Bombardier Inc. Filed by the FAA in regulations.gov docket FAA-2014-0010; AD 2014-13-06 incorporates this document by reference. Not covered by OpenAirDocs’ CC0 dedication. Some pages are OCR from a scan. OCR can misread letters and numbers. Each page's text from the PDF; open the PDF at a page with #page=N.

### Page 1

b 2
THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
LEARJET 40
RT 40-78-03
Revision Transmittal Sheet
RT 40-78-03
Page 1 of 2
Nov 5/12
APPROVED IN WHITE
This page transmits Revision 1 to Service Bulletin No. 40-78-03, “Installation of the Thrust Reverser and Ser-
vice Island Mounting Flange Gaskets.”
Rework:
No rework is required for aircraft which have complied with previous issues of this document.
Summary:
This revision adds E-Seal part number 0945 to the 4578330002-801 and -802 kits. A note has been added
to the each of the accomplishment inst ructions for the -801 and -802 kits  explaining the importance of fol-
lowing the Maintenance Manual instructions for removal of the high pressure bleed air manifold to avoid a
complete engine removal.
NOTE: Change bars are placed in the left margin of  pages where significant changes are located. This
revision incorporates the latest document form at for Learjet service instructions. The general
arrangement of this document may change from the previous issue.
Description of Changes
In the Material Information section:
Changed the 4578330002-801 kit information as follows:
Added part number NAS620C10L washer, quantity 29.
Added part number 0945 E-Seal to the kit parts list.
Changed the 4578330002-802 kit information as follows:
Added part number 0945 E-Seal to the kit parts list.
In the Accomplishment Instructions section:
Changed the Modification Instructions section as follows:
Added a note at two places following the steps to remove the high pressure bleed air manifold to
explain the importance of following the Mainte nance Manual procedures for removal of the high
pressure bleed air manifold.
In the Illustrations section:
Changed Figure 1, Sheet 1 as follows:
Changed callout from “AFT INNER FAIRIN G ASSEMBLY” to “AFT EN GINE MOUNT FAIRING
ASSEMBLY .”
Added callout to the inner fan duct.
Changed Figure 1, Sheet 6 as follows:
Changed verbiage at the end of Flagnote 5 from “...composite duct fan” to “...composite fan duct.”

### Page 2

LEARJET 40
Revision Transmittal Sheet
THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
RT 40-78-03
Page 2 of 2
Nov 5/12
Filing Instructions:
This is a COMPLETE revision. Remove and discard all pages of the prior issue and replace them with
pages of Revision 1. 
Record of Revisions:
ISSUE DISTRIBUTION  DATE
Basic Feb  27/12
Revision  1N o v  5/12

### Page 3

b 2
THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
Refer to applicable government agency regulations and requirements and make sure that the work described 
in this publication is performed in compliance with manufacturer’s recommendations and/or acceptable industry standards. 
This document is proprietary to Bombardier Inc. and/or its affiliates and may not be reproduced or copied in any form or by 
any means without the prior written consent of Bombardier Inc. and/or its affiliates. 
© 2012, Bombardier Inc. All rights reserved. 
Challenger*, Global Express*, Learjet*, are Trademarks of Bombardier Inc.
SB 40-78-03
Recommended
Page 1 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
Contact  Information Distribution  Date Rev .  No.  
Business Aircraft 
Learjet Inc.
MS 53
P .O. Box 7707
Wichita, Kansas 67277‐7707
Customer Response Center (CRC)
1‐866‐538‐0247 (Toll Free)
(316) 946‐6100 (Tel)
Push 2 for Parts Services or push 4 then 
push 1 for Technical Publications.
November 5, 2012 1
LEARJET 40
If you cannot complete the instructions in this publication because of an STC change to the aircraft, speak to
the STC holder or the regional Federal Aviation Administration (FAA) office for information and disposition.
Service Bulletin
These commodities, technology or software were exported from the United States in accordance
with the Export Administration Regulations. Diversion contrary to United States law is prohibited.
SB 40-78-03
Recommended
POWERPLANT - INSTALLATION OF THE THRU ST REVERSER AND SERVICE ISLAND MOUNT-
ING FLANGE GASKETS
1. Planning Information
A. Effectivity
(1) Learjet 45-2001 thru 45-2132 with composite fan duct installed.
B. Reason
(1) To improve the corrosion resistance of the thrust  reverser and service island flanges where they
attach to the engine composite fan duct. 
C. Description
(1) This service bulletin provides in structions to perform Nordam Service Bulletin 5045-78-13 and to
install the thrust reverser and service island mounting flange gaskets to prevent corrosion. A seal-
ant barrier is also applied between the composite fan duct mounting flange and the thrust reverser
and service island mounting flanges to improve corrosion resistance.

### Page 4

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 2 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
D. Compliance
(1) Recommended - Bombardier Learjet Inc. recomme nds that you complete these instructions within
the next 1200 flight hours or the next C phase inspection, whichever comes first.
E. Approval
(1) The Federal Aviation Administration (FAA) has ap proved the technical content in this publication
that has an effect on the airplane type design.
(2) The European Aviation Safety Agency (EASA) has  accepted the technical content in this publica-
tion that has an effect on the airplane type design.
F. Labor Hours - Estimated Accomplishment Time
NOTE: These labor hours are an estimate and ar e for planning purposes only. Facility and per-
sonnel capabilities may cause the labor hours to change.
When planning to complete these instructions, please contact Bombardier Aerospace,
Learjet Inc. Business Aircraft  Customer Service, Parts Serv ices for parts availability and
shipping times as necessary. (Refer to the title page of this document for contact informa-
tion.)
G. Expense Coverage
(1) Labor Coverage - Labor coverage applies to all aircraft affected by this publication.
NOTE: For labor coverage to apply, you must complete these instructions at a Bombardier
Business Aviation Service Fa cility or at a Bombardier Learjet Authorized Service
Facility. You must complete these instructions within 48 months from the Basic Issue
distribution date of this publication.
(2) Material Coverage - Material coverage applies to all aircraft affected by this publication.
NOTE: For material coverage to apply, you must place an order for these parts from Bombar-
dier Learjet within 48 months from the Basic Issue distribution date of this publication.
(3) Smart Parts Plus Coverage
(a) During or after the above free period, Smart Parts Plus does not pay for the kits.
‐801  KIT ‐802  KIT TASK
3.5 3.5 Labor  hours  to gain  access.
20.0 10.0 Labor  hours  to do the  aircraft  modification.
4.0 4.0 Labor  hours  to do a functional  test/operational  check.
3.5 3.5 Labor  hours  to return  the  aircraft  to airworthy  status.
31.0 21.0 Total  Labor  Hours

### Page 5

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 3 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
H. Material Required
NOTE: * One kit must be ordered for each engine.
Refer to Paragraph 2.A. to know which kit is necessary
The above prices can change.
(1) Other materials/parts necessary to complete these instructions.
I. Tools and Equipment
(1) Refer to Nordam Service Bulletin 5045-78-13.
(2) Refer to the Sections in Chapter 24 of the Maintenance Manual as follows:
(a) "Disconnection of Electrical Power from the Aircraft."
(b) "Connection of Electrical Power to the Aircraft."
(3) Refer to the Sections in Chapter 36 of the Maintenance Manual as follows:
(a) "Removal of the High Pressure (HP) Bleed Air Manifold Assembly."
(b) "Installation of the High Pressure (HP) Bleed Air Manifold Assembly."
(4) Refer to the Section in Chapter 78 of the Maintenance Manual as follows:
(a) "Removal of the TR Assembly."
PART  NUMBER QTY NOMENCLATURE PRICING
4578330002 ‐801
(* See  Note)
1S e r v i c e  Bulletin  Kit $1,476.85
4578330002 ‐802
(* See  Note)
1S e r v i c e  Bulletin  Kit $1,216.00
PART  
NUMBER NOMENCLATURE QTY MANUFACTURER
RTV  159  (Red)  
or equivalent
Adhesive As  
Req’ d
General  Electric
Waterford,  NY .
S408  
or equivalent
Parting  Agent  
(Dry  Film)
As 
Req’ d
Stoner
Quarryville,  PA.
ProSeal  890  B1/2,  
Class  B 
or equivalent
Sealing  Compound As  
Req’ d
PRC ‐Desoto  
International  
Glendale,  CA.
ProSeal  890  B2,  
Class  B 
or equivalent
Sealing  Compound As  
Req’ d
PRC ‐Desoto  
International  
Glendale,  CA.

### Page 6

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 4 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
J. Weight and Balance
(1) Change in basic weight and balance.
NOTE: The above weight and moment change is fo r one thrust reverser kit. If this modifica-
tion is done to both thrust reversers, the weight and moment must be doubled. 
K. References
(1) Learjet Maintenance Manual, Chapters 20, 24, 36, 71 and 78. 
(2) Nordam Service Bulletin 5045-78-13.
(3) Garrett TFE-731 Engine Maintenance Manual.
2. Material Information
A. Parts Required
(1) The 4578330002-801 kit is for aircraft 45-200 1 thru 45-2129 equipped with composite fan ducts
and contains the parts that follow:
NOTE: The kit that follows is for one thrust reverser. Two kits are required to do both thrust
reversers.
CHANGE  IN BASIC  WEIGHT CHANGE  IN BASIC  MOMENT
Plus  (+)  0.24  lbs
(See  Note)
Plus  (+)  106.2  in/lbs
(See  Note)
PART  
NUMBER QTY NOMENCLATURE ALTERNATE  PART  NUMBER
B0201076D3 ‐73 7 B o l t
VN936NP3C 37 Washer AS4987NP3C
NAS620C10L 29 Washer
4578300009 ‐001 1 Gasket,  Lower
4578300008 ‐001 1 Gasket,  Outboard
4578300007 ‐001 1 Gasket,  Upper
4578300006 ‐001 1 Gasket,  Service  Island
NAS1802 ‐3‐71 S c r e w
NAS1149C0316R 1 Washer
MS9592 ‐010 1 Bracket
MS21042 ‐31 N u t
MS21919WH4 1 Clamp
MS21919WH5 1 Clamp
0945 1 E ‐Seal

### Page 7

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 5 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
NOTE: Some hardware comes in pre-packaged quantities. When that occurs, the quantity in the
kit will be more that the quantity in the parts list.
(2) The 4578330002-802 kit is for aircraft 45-2130 thru 45-2132 and contains the parts that follow:
NOTE: The kit that follows is for one thrust reverser. Two kits are required to do both thrust
reversers.
NOTE: Some hardware comes in pre-packaged quantities. When that occurs, the quantity in the
kit will be more that the quantity in the parts list.
3. Accomplishment Instructions
A. Gain Access
(1) Disconnect external electrical power and the main and emergency batteries from the aircraft.
(Refer to Chapter 24 of the Maintenance Manual.)
(2) Remove the upper and lower engine cowling from  the engine that is being modified (LH, 450AL
and 450CL; RH, 460AR and 460CR). (Refer to Chapter 71 of the Maintenance Manual.)
(3) Remove the lower pylon access panels (LH, 340DL, 340EL, 340FL; RH, 340DR, 340ER, 340CR)
as required.
PART  
NUMBER QTY NOMENCLATURE
4578300009 ‐001 1 Gasket,  Lower
4578300008 ‐001 1 Gasket,  Outboard
4578300007 ‐001 1 Gasket,  Upper
4578300006 ‐001 1 Gasket,  Service  Island
NAS1802 ‐3‐71 S c r e w
NAS1149C0316R 1 Washer
MS9592 ‐010 1 Bracket
MS21042 ‐31 N u t
MS21919WH4 1 Clamp
MS21919WH5 1 Clamp
0945 1 E ‐Seal

### Page 8

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 6 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
B. Inspection/Modific ation of Aircraft
NOTE: The instructions th at follow are for the left engine. Instructions for the right engine are the
same.
(1) On aircraft 45-2001 thru 45-2129 (-801 kit) with composite fan ducts installed, do the steps that fol-
low:
(a) Remove the thrust reverser from the engine and discard the attaching hardware. Retain the
nutplate mounting rings for later installation. (Refer to Chapter 78 of the Maintenance Manual.)
(b) Remove the high pressure bleed air manifold. (Refer to Chapter 36 of the Maintenance Man-
ual.)
NOTE: It is important to follow the procedure steps for removal of the high pressure bleed
air manifold as outlined in Chapter 36 of the Maintenance Manual to avoid a com-
plete engine removal. These procedures al so include instruct ions for removal of
the service island, the aft engine mount assembly, and the aft engine mount fair-
ing assembly. 
(c) Remove and discard the service island mating flange hardware.
(d) Do Nordam Service Bulletin 5045-78-13.
(e) Solvent clean the composite fan duct flange. (Refer to Chapter 20 of the Maintenance Man-
ual.)
(f) Attach the thrust reverser and service island  to the composite fan bypass duct as follows:
1) Apply a coat of parting agent to the compos ite bypass duct flange and both sides of the
gasket and allow to dry to the touch before attaching the thrust reverser and service
island. (Refer to Chapter 20 of the Maintenance Manual.)
CAUTION: DO NOT ABRADE THE GREEN EPOXY PRIMED SURFACES.
2) To improve sealant adhesion, lightly abrade the gloss painted surfaces of the thrust
reverser and service island where the sealant is to be applied. DO NOT abrade green
epoxy primer. (See Figure 1, View E-E.) 
3) Solvent clean abraded area. (Refer to Chapter 20 of the Maintenance Manual.)
4) Apply Class B (890 B2) sealant to the thrust reverser and service island flanges.
NOTE: When applying sealant, completely cover the mating flange surfaces, outer
flange edge and a 1.0 (± 0.25) in [2.54 cm (± 6.35 mm)] band on inner sur-
faces around the entire circumference. (See  Figure 1 , View E-E.) Sealant
must reach a minimum of work life before  mating the thrust reverser and ser-
vice island to the composite fan duct.
5) Install the service island and gasket on th e engine composite fan duct mounting flange
using new attaching hardware. Install the fasteners wet with Class B (890 B1/2) sealant.
Do not torque the attaching hardware at this time. (Refer to Chapter 20 of the Mainte-
nance Manual.)
NOTE: Apply sealant to the shank of the bolt only. Do not apply sealant to the bolt
threads.
6) Install the high pressure bleed air manifold. (Refer to Chapter 36 of the Maintenance Man-
ual.)

### Page 9

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 7 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
7) Install the thrust reverser and gaskets to the composite bypass fan duct as follows:
a) Apply a coat of parting agent to the comp osite fan duct flange and both sides of the
gasket and allow to dry to the touch before attaching the thrust reverser and service
island. (Refer to Chapter 20 of the Maintenance Manual.)
b) Locate the thrust reverser ga skets in their correct positions.
c) Locate the thrust reverser  in its correct position.
d) Wet install the thrust reverser with the attaching hardware with Class B (890 B1/2)
sealant. DO NOT perform the functional test at this time as instructed in Chapter 78 of
the Maintenance Manual.
NOTE: Apply sealant to the shank of the bolt only. Do not apply sealant to the bolt
threads.
8) Torque the service island and thrust reverser attaching hardware to 50 to 70 in/lbs [5.64 to
7.90 Nm] above rundown torque. (Refer to Chapter 20 of the Maintenance Manual.)
9) Install the wiring and throttle clamps. (See  Figure 1, Detail F.)
(2) On aircraft 45-2130 thru 45-2132 (-802 kit) with composite fan ducts installed, do the steps that fol-
low:
(a) Remove the thrust reverser from the engine and retain the attaching hardware. (Refer to
Chapter 78 of the Maintenance Manual.)
(b) Remove the high pressure bleed air mani fold and retain the hardware. (Refer to Chapter 36 of
the Maintenance Manual.)
NOTE: It is important to follow the procedure steps for removal of the high pressure bleed
air manifold as outlined in Chapter 36 of the Maintenance Manual to avoid a com-
plete engine removal. These procedures al so include instruct ions for removal of
the service island, the aft engine mount assembly, and the aft engine mount fair-
ing assembly. 
(c) Inspect the thrust reverser flange for damage to the sealant.
(d) Apply Class B sealant (890 B2) to the thrust reverser flange and service island flange where
necessary. Sealant must reach a minimum of work  life before mating the thrust reverser and
service island to the composite fan duct. (See Figure 1.)
(e) Install the service island to the co mposite bypass fan duct as follows:
1) Apply a coat of parting agent to the compos ite bypass fan duct flange and both sides of
the gasket and allow to dry to the touch before attaching the thrust reverser and service
island. (Refer to Chapter 20 of the Maintenance Manual.)
2) Position the gasket between the service island and fan duct assembly.
3) Wet install the attaching hardware that was previously removed with Class B (890 B1/2)
sealant. Do not torque attaching hardware at this time.
NOTE: Apply sealant to the shank of the bolt only. Do not apply sealant to the bolt
threads.
(f) Install the high pressure bleed air manifold. (Refer to Chapter 36 of the Maintenance Manual.)
NOTE: Do not install the thrust reverser as instructed in Chapter 78 of the Maintenance
Manual. Refer to the steps that follow to install the thrust reverser.
(g) Install the thrust reverser and gaskets to  the composite bypass fan duct as follows: 
1) Apply a coat of parting agent to both sides of the gasket and allow to dry to the touch
before attaching the thrust reverser. (Refer to Chapter 20 of the Maintenance Manual.)

### Page 10

THIS PUBLICATION IS AVAILABLE AT:
www.cic.bombardier.com
SB 40-78-03
Recommended
Page 8 of 14
Basic Issue: Feb 27/12
Revision 1: Nov 5/12
LEARJET 40
Service Bulletin
2) Locate the gaskets between the thrust reverser and the composite bypass fan duct in their
correct positions. (See Figure 1, Detail D.)
3) Install the thrust reverser to the composite bypass fan du ct with previously removed
attaching hardware. Install fasteners wet with Class B (890 B1/2) sealant. (Refer to Chap-
ter 20 of the Maintenance Manual.)
NOTE: Apply sealant to the shank of the bolt only. Do not apply sealant to the bolt
threads.
(h) Torque the service island and thrust reverser attaching hardware to 50 to 70 in/lbs [5.64 to
7.90 Nm] above rundown torque. (Refer to Chapter 20 of the Maintenance Manual.)
(i) Install the wiring and throttle clamps. (See  Figure 1, Detail F.)
C. Functional Test/Operational Check.
(1) Connect the main and emergency batteries and exte rnal electrical power to  the aircraft. (Refer to
Chapter 24 of the Maintenance Manual.)
(2) Do the Engine Operation Check and examine for l eaks. (Refer to Garrett TFE-731 Engine Mainte-
nance Manual.)
(3) Do the Operational Check of Thrust Reverser  System and examine for leaks. (Refer to Chapter 78
of the Maintenance Manual.) 
(4) Do the Operational Check of the Bleed Air System and examine for leaks. (Refer to Chapter 36 of
the Maintenance Manual.)
NOTE: Make sure no leaks exist around the coupli ngs of the high pressure bleed air manifold.
D. Return Aircraft to Airworthy Status
(1) Install the lower pylon access panels (LH, 340D L, 340EL, 340FL; RH, 340DR, 340ER, 340CR) as
required.
(2) Install the upper and lower engine cowling (L H, 450AL and 450CL; RH, 460AR and 460CR).
(Refer to Chapter 71 of the Maintenance Manual.)
(3) If not already done, connect the main and emergency batteries to the aircraft. (Refer to Chapter 24
of the Maintenance Manual.)
E. Compliance Response Form
(1) Complete the compliance response form.
(2) Send the compliance response form to Learjet Inc. as soon as possible.
F. Aircraft Maintenance Records
(1) Complete the Aircraft Maintenance Records in accordance with the regulatory requirements of
your aircraft certification authority.

### Page 11 (OCR)

LEARJET 40
Service Bulletin
B
FWD
Detail A
AFT ENGINE MOUNT
FAIRING ASSEMBLY
(REF)
COMPOSITE
FAN DUCT
SERVICE  (REF)
INNER  ISLAND
FAN DUCT  (REF)
(REF)  AFT ENGINE
MOUNT
(REF)
HIGH PRESSURE
BLEED AIR  RETAINER
MANIFOLD  (REF)
(REF)
SCREW
HIGH PRESSURE  (REF)  HOSE  FWD
BLEED AIR  CLAMP
FIRE SEAL  (REF)
(REF)  BUMPER
PLATE  HIGH PRESSURE
(REF)  WASHER  BLEED AIR DUCT
(REF)
NOTE  (REF)
Notes information is found on  the last sheet of the figure.  Detail B
K40-407803-001-01
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 1 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 9 of 14

### Page 12 (OCR)

LEARJET 40
Service Bulletin
SERVICE
ISLAND
-(REF)
> AFT ENGINE
MOUNT FIRE
SEAL
/ (REF)
AFT ENGINE
MOUNT
(REF)
PLATE
(REF)
PAN
ASSEMBLY
(REF)
BOLT
(REF)  (3)
Detail C
K40-407803-001-02
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 2 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 10 of 14

### Page 13 (OCR)

LEARJET 40
Service Bulletin
BOLT
B0201076D3-7
WASHER (UNDER HEAD)
VN936NP3C
(1 EACH REQUIRED,
37 PLACES)
UPPER THRUST  WASHER
REVERSER GASKET  NACELLE  NAS620C10L
4578300007-001  BL  (1 EACH REQUIRED,
(1 REQUIRED)  0.00  28 PLACES LH AND
29 PLACES RH)
E
SERVICE
ISLAND
GASKET
4578300006-001  E  ALIGNMENT
PIN
(1 REQUIRED)
(REF)
NACELLE
WL
100.00
:10
LOWER THRUST  OUTBOARD THRUST
REVERSER GASKET  REVERSER GASKET
4578300009-001  4578300008-001
(1 REQUIRED)  (1 REQUIRED)
ENGINE ATTACH FLANGE
MEW LOOKING AFT, LH SHOWN, RH OPPOSITE)
Detail D
K40-407803-001-03
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 3 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 11 of 14

### Page 14 (OCR)

LEARJET 40
Service Bulletin
-1.00 in (‡ 0.25 in)
12.54 cm (‡ 6.35 mm)]
INNER SURFACE
• (REF)
5 SEALANT AREA
TO
ENGINE
C/L  FLANGE
(REF)
FWD C
THRUST REVERSER FLANGE CROSS SECTION
View E-E
LEFT
ENGINE  SERVICE
FLANGE  ISLAND
(REF)  (REF)
THROTTLE
CABLE
(REF)
' THROTTLE
G  BUNDLE  (REF)
LEFT ENGINE SERVICE ISLAND INSTALLATION
(FLANGE HARDWARE NOT SHOWN FOR CLARITY)
(VIEW ROTATED 180 DEGREES CLOCKWISE)
Detail F
K40-407803-001-04
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 4 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 12 of 14

### Page 15 (OCR)

LEARJET 40
Service Bulletin
н б  OIL TEMPERATURE
REGULATOR
(REF)
THROTTLE CONTROL
CABLE ASSEMBLY
(REF)
— FUEL PUMP
(REF)
ENGINE WIRE
BUNDLE
(REF)
View G-G
CLAMP
MS21919WH5
SCREW  (1 REQUIRED)  CLAMP
NAS1802-3-7  BRACKET  MS21919WH4
(1 REQUIRED)  MS9592-010  (1 REQUIRED)
(1 REQUIRED)
WASHER
NAS1149C0316R  FLANGE
(1 REQUIRED)  (REF)
FLANGE
NUT  - (REF)
MS21042-3
(1 REQUIRED)
(USE SECOND HOLE LOCATION
BELOW THE SERVICE ISLAND)
View H-H
(USE FIRST HOLE LOCATION
BELOW THE SERVICE ISLAND)
View J-J
K40-407803-001-05
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 5 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 13 of 14

### Page 16 (OCR)

LEARJET 40
Service Bulletin
NOTES
When removing RTV159 adhesive from the aft engine mount fire seal, make sure not to cut
the fire seal. If the fire seal is cut, torn or damaged, the engine will need to be removed to
replace the seal.
Apply RTV159 adhesive in the gap between the aft engine mount fire seal and the pan assembly.
Torque bolts to 50 to 70 in-Ibs [5.64 to 7.90 Nm], above rundown torque.
On aircraft 45-2001 thru 45-2129, equipped with composite fan ducts, apply parting
agent to entire circumference of the engine composite fan duct mounting flange.
On aircraft 45-2001 thru 45-2129, equipped with composite fan ducts, apply Class B (890 B2)
sealant to the thrust reverser and service island flanges. Completely cover the mating flange
surfaces, outer flange edge and a 1.00 in (‡ 0.25 in) [2.54 cm (+ 6.35 mm)] band on inner
surfaces around entire circumference. Sealant must reach a minimum of work life before
mating the thrust reverser and service island to the composite fan duct.
Do not install NAS620C10L washer in these six locations.
It is acceptable to install one NAS620C10L washer between the VN936N93C washer and the thrust
reverser flange to prevent the bolt shank from bottoming out on the nutplate (22 places).
It is acceptable to add or relocate clamps to secure the throttle cable and wire harness around the oil
temperature regulator. Relocate or add clamp for the wire bundle to the first hole location below the
service island. Relocate or add a clamp for the throttle cable in the second hole location below the
service island.
Do not install NAS620C10L washer in these two locations on the right engine.
Do not install NAS620C10L washer in these three locations on the left engine.
K40-407803-001-06
Installation of the Thrust Reverser and Service Island Mounting Flange Gaskets
Figure 1 (Sheet 6 of 6)
Basic Issue: Feb 27/12  THIS PUBLICATION IS AVAILABLE AT:  SB 40-78-03
Revision 1: Nov 5/12  www.cic.bombardier.com  Recommended
Page 14 of 14

---
OpenAirDocs.org is an independent research project of [Contrail Labs](https://contraillabs.com/). It is not affiliated with the FAA or the NTSB. Source documents are U.S. government works in the public domain, except the copies of manufacturers’ service documents, which belong to their rights holders.
